Stiga Lawn Mower Accessory 8211 1227 02 User Manual

STIGA

COLLECTOR 30

INSTRUCTIONS FOR USE

8211-1227-02

Download from Www.Somanuals.com. All Manuals Search And Download.

SVENSKA

10.

11.

12.

Download from Www.Somanuals.com. All Manuals Search And Download.

SVENSKA

13.

14.

15.

17.

19.

16.

18.

Download from Www.Somanuals.com. All Manuals Search And Download.

ENGLISH

Assembly of brush unit

Figures and letters in brackets refer to the figures.

SAFETY INSTRUCTIONS

1. See fig. 3. Undo the existing nuts in the middle

on the front of the brush unit (1). Remove the

flat washers. Position the connecting rod (15)

on the carriage bolts. Install the washers and the

nuts. Do not tighten the nuts yet.

1. Never allow anyone to use the collector without

correct instructions.

2. Do not allow children to use the collector.

3. Do not operate the machine too close to naked

flames, as the hopper bag and the brushes are

highly flammable.

2. See fig. 3. Install the strut (9) on the brush unit

with the aid of two screws (D) with the heads on

the inside of the brush unit. Position two wash-

ers (I) and two locking nuts (G) on the outside.

Do not tighten the nuts yet.

4. Do not attempt to remove objects that have be-

come caught up in the brush (e.g. pieces of

string) while the brush is rotating.

5. Move at reduced speed over uneven surfaces

and on slopes to ensure you do not lose control

or the machine does not tip over. Watch out for

holes and other hidden dangers.

3. See fig. 3. The installation of the angle (14) de-

termines the height of the hopper bag above the

ground (see below).

•

The bottom of the hopper bag must be horizon-

tal.

6. This collector is not intended to be driven on

public roads. Watch out for traffic when using

the machine close to streets and roads.

•

The distance to the ground must be 8-10 cm

when the height setting arm (7) is in the central

position.

7. Ensure that all screws and nuts are tightened so

that the collector is in good condition.

•

Never allow the hopper bag to drag on the

ground.

8. Stop and check the collector for damage follow-

ing a collision. Any damage must be repaired

before the collector is used again.

By installing the angle on the top or bottom of

the connecting rod (15), along with the spacers,

many different heights can be obtained.

9. Follow all the instructions in this set of instruc-

tions regarding maintenance of the collector.

•

Test which installation best suits the lawnmow-

er in question.

DELIVERY

Continue assembly as follows:

Install the angle (14) on the connecting rod with

a screw (B) and a locking nut (F) in the front

hole. Use a longer screw (A), the bracket (V)

and a locking nut (F) in the rear hole. Position

the strut (9) under the bracket (V). Do not tight-

en the nuts yet.

The delivery comprises a box containing the com-

ponents in fig. 2 as well as a bag. The bag contains

the installation components in fig. 1. The follow-

ing number (x) indicates the quantity of the rele-

vant component.

4. Tighten the nuts that were installed under point

3 above. Do not tighten too hard, as this could

deform the tube. Press the connecting rod (15)

down so that the strut (9) comes under the

bracket (V), and press against the screw (A).

Tighten all the screws and nuts that have been

installed.

ASSEMBLY

Tools

The following tools are required for assembly:

•

Adjustable wrench

Box wrenches 3/8 - 7/16 - 1/2 - 9/6

Screwdriver

5. See fig. 4. Undo both locking nuts on the height

setting tube (6). Remove the dished washers.

Install the height setting lever (7) on the tube.

Screw in the height setting lever.

Pliers

Hammer

6. Press the handle (S) onto the height setting lever

with the finger grip facing forwards.

7. See fig. 4. Install the angle (W) on the connect-

ing rod with a screw (C) and a locking nut (G).

Download from Www.Somanuals.com. All Manuals Search And Download.

ENGLISH

8. Install the height setting strut (8) on the angle

The hopper bag supports are made of

powerful spring steel. Wear protective

goggles during assembly.

(W). Position the spacer (K) on the screw (E).

Insert the screw with the spacer through the

hole in the height setting strut and into the hole

in the angle. Lock in place with the locking

washer (J) and the nut (H).

11.See fig. 13. Tension the two sprung struts (11)

in the rear part of the hopper bag.

12.See fig. 14. Locate the holes in the sides of the

hopper bag and make holes with an awl or sim-

ilar.

9. Attach the other end of the height setting strut

(8) to the height setting arm (7). Position the

groove in the height setting strut opposite the

square hole in the arm.

13.See fig. 15. Install the hopper bag locks (X), the

pins (P) and the locking pins (M) in both sides

of the hopper bag.

10.Screw into place with a carriage bolt (D), a flat

washer (I) and the locking wheel (T).

NOTE! The hopper bag locks must be able to

move about freely.

11.See fig. 5. Install the two securing arms (5) on

the outside of the brush unit. Screw the securing

arms into the rear, lower holes with four screws

(B) and four locking nuts (F).

14.See fig. 16. Install the line (15).

15.Install the wind protection on the rear upper

section of the hopper bag.

NOTE! The grooves in the securing arms must

be facing up.

16.See fig. 17, 18. Install the hopper bag on the

brush unit.

12.Install the hitch pin (U) and the two spacers (L)

in the connecting rod. Lock with the locking

pins (N).

USING THE MACHINE

Assembling the hopper bag

Figures and letters in brackets refer to the figures.

Operating

Be careful when driving on slopes.

1. See fig. 6, 7. Insert the left-hand, upper hopper

bag tube (1) in the hopper bag flap. Start at the

cut-out in the middle of the hopper bag’s upper

section. The holes in fig. 6 must be facing

down.

The vehicle’s braking characteristics and stability

can be affected by installed accessories or optional

extras. Be particularly careful when driving on

slopes.

2. Install the right-hand, upper hopper bag tube (1)

in the same way and press the tubes together.

Hopper bag height

Set the hopper bag so that its bottom is horizontal

and is 8-10 cm above the ground when driving. See

point 3 under “ASSEMBLY”.

3. Secure the tubes by pressing in a plastic plug

(R) through the holes.

4. See fig. 7. Locate the holes in the sides of the

two upper hopper bag tubes. These will be used

later.

Brush height setting

5. See fig. 9. Assemble the two lower hopper bag

tubes (3, 4).

Set the brushes to the correct height by undoing the

locking wheel and then moving the arm up or

down, see fig. 19. If the arm is moved down, the

brushes are raised. The best results are obtained if

the brushes sweep the top of the grass without

touching the soil below. The brushes must not be

lowered so much that the collector’s wheels slide

or slip.

6. See fig. 9. Secure the tubes by pressing in a

plastic plug (R) through the holes.

7. Position the lower hopper bag tubes inside the

hopper bag.

8. See fig. 10. Assemble the two upper and lower

hopper bag tubes’ ends using the pins (Q) and

the locking pins (M).

Speed

9. See fig. 11. Attach the hopper bag’s front strut

to the lower hopper bag tubes using the pins (O)

and the locking pins (M).

•

Test which speed produces the best results.

•

The speed should be selected so that the grass is

thrown to the rear part of the hopper bag.

10.See fig. 12. Snap the hopper bag together

around the bag tubes using the snap fasteners.

•

Recommended speed: 4.8 - 6.4 km/h.

Download from Www.Somanuals.com. All Manuals Search And Download.

ENGLISH

Emptying

The collector’s hopper bag is easily emptied by

pulling the cord from the driver’s seat.

STORAGE

The hopper bag can be folded up if both the hopper

bag supports (11) are removed. Requires less room

for storage.

Do not secure the cord to the ride-on mower in

such a way that it catches in the wheels or in other

rotating parts.

Do not drive too close to naked flames when using

or emptying, as the hopper bag and the brushes can

be damaged by heat or fire.

Always empty the hopper bag after each use.

Damp or wet grass and leaves can cause damage if

stored for an extended period.

MAINTENANCE

The collector must be cleaned after each use. Dried

on grass remains damage the collector and impair

its performance. Carefully clean the inside of the

hopper bag and clean the brushes of twigs etc.

Take care when rinsing with water. Make

sure that no water penetrates into bearings

and other moving parts.

Every two years, the wheels should be dismantled

and the gear rim and the cog wheels lubricated

with oil or thin grease.

To dismantle the wheel, snap off the wheel cap,

disconnect the locking ring, remove the flat washer

and then remove the wheel.

The collector’s bearings are lubricated in the facto-

ry. However, you are recommended to apply a few

drops of oil on the brush axle bearings a couple of

times a year.

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

....................................................................................................................................................................

Download from Www.Somanuals.com. All Manuals Search And Download.

M O W I N G A H E A D

GGP Sweden AB

Box 1006

SE-573 28 TRANÅS

www.st iga.co m

Download from Www.Somanuals.com. All Manuals Search And Download.

Billy Goat Lawn Mower KV600 User Manual
Craftsman Lawn Aerator 48624326 User Manual
Dixon Lawn Mower ZTR 3II User Manual
Exmark Lawn Mower 4500 872 User Manual
Exmark Lawn Mower Lazer Z User Manual
Land Pride Lawn Mower ZSR60 User Manual
McCulloch Lawn Mower 96141014601 User Manual
Snapper Lawn Mower L21500 User Manual
Snapper Lawn Mower P2187520BVE (7800432) User Manual
Troy Bilt Lawn Mower 634A User Manual