SWITCH BLADE
5 ft. & 6 ft. Sickle Bar Mower
Model With Spring Break-A-Way
Rev 08-11
Part No. 02974374P
PART'S MANUAL
An Operator's Manual was shipped with the equipment in the Manual Canister.
This Operator's Manual is an integral part of the safe operation of this machine
and must be maintained with the unit at all times. READ, UNDERSTAND, and
FOLLOW the Safety and Operation Instructions contained in this manual before
operating the equipment. If the Operator's Manual is not with the equipment,
contact your dealer or Alamo Industrial (800-356-6286) to obtain a Free copy
before operating the equipment.
ALAMO INDUSTRIAL
1502 E. Walnut
®
®
Seguin, Texas 78155
210-372-3551
© 2011 Alamo Group Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
TO THE OWNER/OPERATOR/DEALER
All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recog-
nizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with
all its safety equipment properly attached to minimize the chance of accidents.
BEFORE YOU START!!Read the safety messages on the implement and shown in your manual.
Observe the rules of safety and common sense!
WARRANTY INFORMATION:
Read and understand the completeWarranty Statement found in this Manual. Fill out theWarranty Registration Form in full and return
it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that
you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT TORQUE
Mounting procedures for mowers will require a significant amount of bolt nut and washer installation.
Frame and structure mounting bolts should be installed using Red Loctite, and torqued to the dry values
listed in the torque chart based on the bolt size and hardness.
Other structures such as pump mounting bolts should be installed with Blue Loctite and torqued to the dry
values indicated in the chart.
Bolt tightness should be completed with and checked with a suitable torque wrench.
Torque checks should be completed throughout the life of the mower in accordance with the maintenance
chart provided in this manual.
Loose bolts on a frame or in a casting may be a result of:
● Vibration from the mower due to imbalance of the mower blades
● Pulled threads due to over tightening
● Distortion of the hole due to under tightening during installation
Bolts broken or sheared in the mounting structure or tractor may be the result of:
● Improper alignment of the Mounting Plate or Structure such that it is not sitting flat on the mating
surface
● Distortion of the bolt due to over-tightening
● Under tightening of the bolts
Check the bolt torque during installation and prior to delivery with a suitable torque wrench.
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS
SECTION
Parts Section – 1
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING GUIDE
The following instructions are offered to help eliminate needless delay and error in processing
purchase orders for the equipment in this section.
1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the
basic machine featured in this manual. Part Numbers and Descriptions are given to help locate
the parts and quantities required.
2. ThePurchaseOrdermustincludethenameandaddressofthepersonororganizationordering
the parts, who should be charged, and if possible, the serial number of the machine for which
the parts are ordered.
3. The Purchase Order must clearly list the quantity of each part, the complete and correct part
number (be sure to include all periods), and the basic name of the part.
4. The Manufacturer reserves the right to substitute parts where applicable.
5. Some parts are unlisted items which are special production items not normally stocked and
are subject to special handling. Request a quotation for such parts before sending a Purchase
Order.
6. The Manufacturer reserves the right to change prices without prior notice.
Note: Please refer to The Safety Section in the front of this Manual for the proper part number
when ordering replacement safety decals.
For maximum safety and to guarantee optimum product reliability, always use
genuineAlamo Industrial Parts. The use of inferior replacement parts may cause
premature or catastrophic failure which could result in serious injury or death.
Direct any questions regarding parts to:
ALAMO INDUSTRIAL
1502 E. Walnut
®
Seguin, Texas 78155
®
830-379-1480
©2011 Alamo Group Inc.
Parts Section – 2
Download from Www.Somanuals.com. All Manuals Search And Download.
PART NAME INDEX
CARRIAGE ARM ASY - LH WG - PN 02977721........................................................................................................................................ 4
CARRIAGE ARM ASY - RH WG - PN 02974362....................................................................................................................................... 6
COMMON COMPONENT BOX - PN 02974368......................................................................................................................................... 8
CUTTER BAR ASY - 5 FT LH WG - PN 02977715.................................................................................................................................... 9
CUTTER BAR ASY - 5 FT RH WG - PN 02974360.................................................................................................................................. 11
CUTTER BAR ASY - 6 FT LH WG - PN 02977717.................................................................................................................................. 13
CUTTER BAR ASY - 6 FT RH WG - PN 02974372.................................................................................................................................. 15
HYD CYL ASY - BAR TILT - PN 0693500A............................................................................................................................................ 17
HYD CYL ASY - CURB LIFT - PN 0693400A......................................................................................................................................... 18
HYD DIVERTER VALVE - CYL CONTROL - PN 02977622................................................................................................................. 19
HYD DIVERTER VALVE - MOTOR CONTROL - PN 02977621........................................................................................................... 20
HYD DIVERTER VALVES - PN 02977621 & PN 02977622................................................................................................................... 21
HYD FILTER ASY - PN 02974309............................................................................................................................................................ 22
HYD MOTOR ASY - PN 02974301 & PN 02974301A............................................................................................................................. 23
HYD MOTOR DRIVE ASY - PN 02974300 & PN 02974300A................................................................................................................ 25
HYD PUMP ASY - PN 02974302 (SN 10361 09-04 & DOWN)............................................................................................................... 26
HYD PUMP ASY - PN 02974302A (SN 10362 10-04 TO 10770)............................................................................................................. 27
HYD PUMP ASY - PN 02974302B (SN 10771 09-08 & UP).................................................................................................................... 29
HYD PUMP ASY - TANDEM PN 02974303B.......................................................................................................................................... 31
HYD SCHEMATIC - SINGLE WG............................................................................................................................................................ 33
HYD TANK ASY - PN 02981705............................................................................................................................................................... 35
HYD VALVE ASY W-FITTINGS - PN 02982077..................................................................................................................................... 37
HYD VALVE ASY W-O FITTINGS - PN 02974306................................................................................................................................. 39
HYD VALVE REMOTE CONTROL CABLES......................................................................................................................................... 41
HYD VALVE SOLENOID ASY - PN 02988789....................................................................................................................................... 43
KNIFE BAR - 5 FT RH WG - PN 02974361 - W/ SERRATED KNIVES................................................................................................. 44
KNIFE BAR - 6 FT RH WG - PN 02974373 - W/ SERRATED KNIVES................................................................................................. 45
KNIFE BAR - 5 FT LH WG - PN 02977716 - W/ SERRATED KNIVES................................................................................................. 46
KNIFE BAR - 6 FT LH WG - PN 02977718 - W/ SERRATED KNIVES................................................................................................. 47
SHOE & BRK-A-WAY PRE-ASY RH MOUNT - PN 02975986.............................................................................................................. 49
SHOE & BRK-A-WAY PRE-ASY LH MOUNT - PN 02977726.............................................................................................................. 51
SHOE, DRIVE & BRK-A-WAY ASY RH MOUNT - PN 02975194........................................................................................................ 53
SHOE, DRIVE & BRK-A-WAY ASY LH MOUNT - PN 02977727......................................................................................................... 55
WIRING HARNESS - DUAL WG - PN 02977754.................................................................................................................................... 57
WIRING HARNESS - SINGLE WG - PN 02974318................................................................................................................................. 58
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -3
Download from Www.Somanuals.com. All Manuals Search And Download.
CARRIAGE ARM ASY - LH WG - PN 02977721
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -4
Download from Www.Somanuals.com. All Manuals Search And Download.
CARRIAGE ARM ASY - LH WG - PN 02977721
Continued...
ITEM PART NO. QTY.
DESCRIPTION
CARRIAGE ARM ASY, LH WING
RED LUBRICAPS
02977721
1
2
2
4
2
2
3
1
1
1
4
1
1
1
1
000206
2
00752670
00755153
0112700
GREASE FITTING
3
COTTER PIN
4
CARRIAGE PIN
5
0113400
PIN ROLL
6
02045200
02965475
02970702
02977719
02977720
0424200
ELBOW
8
HOSE, # 4 - 18" LG
9
HYD. ADAPTER
10
11
12
14
15
CARRIAGE ARM WLD’MT, LH
PIVOT MOUNT WLD’MT
PIN FOR CYLINDER LUGS
CURB STOP CYLINDER ASY
BAR LIFT CYLINDER ASY
0693400A
0693500A
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -5
Download from Www.Somanuals.com. All Manuals Search And Download.
CARRIAGE ARM ASY - RH WG - PN 02974362
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -6
Download from Www.Somanuals.com. All Manuals Search And Download.
CARRIAGE ARM ASY - RH WG - PN 02974362
Continued...
ITEM PART NO. QTY.
DESCRIPTION
02974362
1
2
2
4
2
2
3
1
1
1
1
4
1
1
CARRIAGE ARM ASY.
1
000206
NO. 2 RED LUBRICAPS<
FITTING,GREASE STRAIGHT 1/4-28
PIN,COTTER 3/16 X 1-1/2 PLATED
CARRIAGE PIN
2
00752670
00755153
0112700
3
4
5
0113400
PIN ROLL 3/8 X2-1/2
6
02045200
02965475
02970702
02974324
02974329
0424200
ADP HYD ELBOW 4MP-4MJ90
HOSE #4 - 4FJX - 4FJX - 18LG
ADP HYD TEE 4MJ-4MJ-4FJX
CARRIAGE ARM CASTING
PIVOT MOUNT CASTING
PIN CLEVIS 7/8 X2-3/4
8
9
10
11
12
14
15
0693400A
0693500A
CURB STOP CYLINDER
BAR LIFT CYLINDER
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -7
Download from Www.Somanuals.com. All Manuals Search And Download.
COMMON COMPONENT BOX - PN 02974368
ITEM PART NO. QTY.
DESCRIPTION
02974368
02964028
02982367
02974310
02974318
02974321
02974322
02974348
02974364
02974962
02975270
1
1
1
1
1
1
1
1
1
1
1
COMMON COMPONENT BOX SINGLE
2
PUSH PULL SWITCH
3
SWITCH KNOB
6
FILTER ELEMENT
7
WIRE HARNESS
8
DECAL, VALVE & SWITCH OPERATION
3 - POSITION TOGGLE SWITCH
HYDRAULIC TANK ASY.
VALVE ASY.
9
10
11
12
13
TOGGLE SWITCH BOOT COVER
DECAL, REVERSING SWITCH INSTRUCTION
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -8
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTER BAR ASY - 5 FT LH WG - PN 02977715
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -9
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTER BAR ASY - 5 FT LH WG - PN 02977715
Continued...
ITEM PART NO. QTY.
DESCRIPTION
5 FT CUTTER BAR ASY LH WING
NUT
02977715
00001200
00019600
00022200
000516
1
1
1
2
1
LOCKWASHER
3
2
LOCKWASHER
4
1
CARRIAGE BOLT
5
02983841
0046400
00999316
0569500
0129000
02983841
02974345
0532600
0571100
0571800
0571900
0593500
0593700
0596200
12666000
02983843
5
LOW ARCH HOLD DOWN CLIP
PLOW BOLT
6
10
22
1
7
NUT
8
OUTER SHOE SOLE, LH
CARRIAGE BOLT
9
1
10
11
12
13
14
15
16
17
18
19
20
4
LOW ARCH HOLD DOWN CLIP
CUTTER BAR, 5 FT
WEAR PLATE
1
4
1
OUTER SHOE ASSEMBLY
PLOW BOLT
10
1
WEAR PLATE
1
OUTER ROCK GUARD
CENTER ROCK GUARD
INNER ROCK GUARD, LH
CARRIAGE BOLT
18
1
1
5
PLASTIC WEAR STRIP .188 THICK
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -10
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTER BAR ASY - 5 FT RH WG - PN 02974360
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -11
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTER BAR ASY - 5 FT RH WG - PN 02974360
Continued...
ITEM PART NO. QTY.
DESCRIPTION
5 FT CUTTER BAR ASY. RH WING
NUT
02974360
00001200
00019600
00022200
000516
1
1
1
2
1
LOCKWASHER
3
2
LOCKWASHER
4
1
CARRIAGE BOLT
5
02983841
0046400
00999316
0123800
0129000
02974345
0532600
0570900
0571800
0571900
0593600
0593700
0593800
12666000
4527
5
LOW ARCH HOLD DOWN CLIP
PLOW BOLT
6
10
12
1
7
NUT
8
OUTER SHOE SOLE, RH
CARRIAGE BOLT
9
1
10
11
12
13
14
15
16
17
18
19
20
4
CUTTERBAR 5 FT
4
WEAR PLATE
1
OUTER SHOE ASSEMBLY, RH
PLOW BOLT
10
1
WEAR PLATE
1
OUTER ROCK GUARD, RH
CENTER ROCK GUARD
INNER ROCK GUARD, RH
CARRIAGE BOLT
18
1
1
10
5
NUT,LOCK FLG WHIZ 7/16-14NC PL
PLASTIC WEAR STRIP .188 THICK
02983843
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -12
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTER BAR ASY - 6 FT LH WG - PN 02977717
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -13
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTER BAR ASY - 6 FT LH WG - PN 02977717
Continued...
ITEM PART NO. QTY.
DESCRIPTION
6 FT CUTTER BAR ASY. LH WING
NUT
02977717
00001200
00019600
00022200
000516
1
1
1
2
1
LOCKWASHER
3
2
LOCKWASHER
4
1
CARRIAGE BOLT
5
02983841
0046400
00999316
0569500
0129000
02974346
0571900
0571100
0571800
0593500
0593700
0596200
12666000
4527
6
LOW ARCH HOLD DOWN CLIP
PLOW BOLT
6
12
14
1
7
NUT
8
OUTER SHOE SOLE, LH
CARRIAGE BOLT
9
1
10
11
12
13
14
15
16
17
18
19
20
1
CUTTER BAR, 6 FT
WEAR PLATE
1
1
OUTER SHOE ASSEMBLY, LH
PLOW BOLT
12
1
OUTER ROCK GUARD
CENTER ROCK GUARD
INNER ROCK GUARD
CARRIAGE BOLT
22
1
1
12
5
FLANGE NUT
0532600
02983843
PLASTIC WEAR INSERTS
PLASTIC WEAR STRIP .188 THICK
6
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -14
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTER BAR ASY - 6 FT RH WG - PN 02974372
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -15
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTER BAR ASY - 6 FT RH WG - PN 02974372
Continued...
ITEM PART NO. QTY.
DESCRIPTION
6 FT CUTTER BAR ASY. RH WING
NUT
02974372
00001200
00019600
00022200
000516
1
1
1
2
1
LOCKWASHER
3
2
LOCKWASHER
4
1
CARRIAGE BOLT
5
02983841
0046400
00999316
0123800
0129000
02974346
0571900
0570900
0571800
0593600
0593700
0593800
12666000
4527
6
LOW ARCH HOLD DOWN CLIP
PLOW BOLT
6
12
14
1
7
NUT
8
OUTER SHOE SOLE, RH
CARRIAGE BOLT
9
1
10
11
12
13
14
15
16
17
18
19
20
1
CUTTER BAR, 6 FT
WEAR PLATE
1
1
OUTER SHOE ASSEMBLY, RH
PLOW BOLT
12
1
OUTER ROCK GUARD, RH
CENTER ROCK GUARD
INNER ROCK GUARD, RH
CARRIAGE BOLT
22
1
1
12
5
FLANGE NUT
0532600
02983843
PLASTIC WEAR INSERTS
PLASTIC WEAR STRIP .188 THICK
6
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -16
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD CYL ASY - BAR TILT - PN 0693500A
ITEM PART NO. QTY.
DESCRIPTION
0693500A
1
1
1
1
1
1
1
1
1
1
BAR LIFT CYLINDER ASY.
1
2
3
4
5
6
7
8
9
02977114
TUBE WLD’MT
02977116
CYL HEAD
02977115
ROD WLD’MT
---------------
---------------
---------------
---------------
---------------
02977121
* O-RING
* BACK-UP SEAL RING
* ROD SEAL
* ROD WIPER
* WIRE RING
SEAL KIT, ( * INCLUDES ITEMS 4, 5, 6, 7 & 8 )
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -17
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD CYL ASY - CURB LIFT - PN 0693400A
ITEM PART NO. QTY.
DESCRIPTION
0693400A
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
CURB STOP CYLINDER ASY.
1
02977114
TUBE WLD’MT
2
02977116
CYLINDER HEAD
PISTON
3
02977118
4
02977122
ROD WLDMT
5
02977123
CYLINDER ROD
6
02716500
LOCKNUT
7
---------------
---------------
---------------
---------------
---------------
---------------
---------------
02977121
* PSP SEAL
8
* O-RING
9
* BACK-UP RING
* ROD SEAL
10
11
12
13
14
* NYLON WEAR RING
* SNAP IN ROD SEAL
* WIRE RING
SEAL KIT, ( * INCLUDES ITEMS 7, 8, 9, 10, 11, 12 & 13 )
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -18
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD DIVERTER VALVE - CYL CONTROL - PN 02977622
ITEM PART NO. QTY.
DESCRIPTION
1
02977622
02988755
02988756
02988819
02988820
1
1
1
1
1
VALVE SOLENOID DIVERTER
SELECTOR, 6WAY, 6GPM SAE-4
COIL, 12 VDC, 6 WAY VS125
SOLENOID, VALVE, SELECTOR
CONNECTOR, DIN, STANDARD
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -19
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD DIVERTER VALVE - MOTOR CONTROL - PN 02977621
ITEM PART NO. QTY.
DESCRIPTION
1
02977621
1
VALVE, SOLENOID DIVERTER (USE W/ DUAL WINGS)
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -20
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD DIVERTER VALVES - PN 02977621 & PN 02977622
ITEM PART NO. QTY.
DESCRIPTION
1
02974962
02977825
02977826
02977622
02962181
02977915
02977621
02962214
00696800
02761100
02977754
1
1
1
1
4
2
1
2
4
2
1
BOOT, TOGGLE SWITCH COVER
DECAL, INSTUCT. LEFT & RIGHT SWITCH
SWITCH, 2-POSITION "ON" & "OFF"
DIVERTER VALVE & SOLENOID, # 4 PORTS
HYD. ADAPTER STRAIGHT
2
3
4
5
6
HYD. ADAPTER ELBOW
7
DIVERTER VALVE & SOLENOID DIVERTER, # 8 PORTS
HYD. ADAPTER ELBOW
8
9
HYD. ADAPTER STRAIGHT
10
11
HYD. ADAPTER ELBOW
WIRE HARNESS, LH DUAL WINGS
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -21
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD FILTER ASY - PN 02974309
ITEM PART NO. QTY.
DESCRIPTION
1
2
3
4
5
6
7
02976906
02976907
02976908
02974319
02976909
02974310
02976910
1
1
1
1
1
1
1
BOWL
FILTER CONDITION GAUGE
FILTER RETAINER SPRING
AIR BREATHER ELEMENT
AIR BREATHER KIT
FILTER ELEMENT
SEAL KIT
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -22
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD MOTOR ASY - PN 02974301 & PN 02974301A
ITEM PART NO. QTY.
DESCRIPTION
02974301
02974301A
02976883
02976884
02976885
02976886
02976887
02976888
02976889
02976890
02976890A
02976891
02976892
02976893
02976894
1
1
1
1
7
4
1
1
1
1
1
1
1
1
1
HORIZONTAL KNIFE DRIVE ASY (W/ 5/16" KEY WAY) SWB6-10672 & DOWN
HORIZONTAL KNIFE DRIVE ASY (W/ 1/4" KEY WAY) SWB5-10673 & UP
1
2
3
4
5
6
7
8
INTERNAL DRIVE SHAFT
STAR & HOUSING SET
HOUSING TIE SCREW
FLANGE ATTACHMENT SCREW
FLANGE MOUNT
THRUST BEARING RACE
THRUST BEARING
OUTPUT SHAFT, (W/ 5/16" KEY WAY) SWB6-10672 & DOWN
OUTPUT SHAFT, (W/ 1/4" KEY WAY) SWB5-10673 & UP
MOTOR HOUSING
9
10
11
12
PLUG
SPACER PLATE
END CAP
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -23
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD MOTOR ASY - PN 02974301 & PN 02974301A
Continued...
ITEM PART NO. QTY.
DESCRIPTION
13
MA000229
1
1
1
1
KEY, 5/16" X 5/16" X 1" LG KEY SWB6-10672 & DOWN
KEY, 1/4" X 1/4" X 1" LG KEY SWB5-10673 & UP
KEY, STEPPED 1/4" X 5/16" X 1" LG KEY (AS NEEDED)
SEAL KIT, GEROTOR MOTOR
102268
03200521
02976895
14
NOTE:THERE WERE TWO DIFFERENT SIZE KEYS USED, A 1/4 INCH AND A 5/16 INCH. TO MIX THESE COMPONENTS THERE IS A STEPPED KEY
AVAILABLE THAT IS 1/4 AND 5/16 INCH. CHECK WHICH IS NEEDED.
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -24
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD MOTOR DRIVE ASY - PN 02974300 & PN 02974300A
ITEM PART NO. QTY.
DESCRIPTION
02974300
02974300A
02974311
02974315
02974315A
02974317
02977820
02980453
02967570
1
1
1
1
1
1
2
1
2
HORIZONTAL KNIFE DRIVE ASY (W/ 5/16" KEY WAY) SWB6-10672 & DOWN
HORIZONTAL KNIFE DRIVE ASY (W/ 1/4" KEY WAY) SWB5-10168 & DOWN
FLYWHEEL
1
2
HUB ADAPTER (W/ 5/16" KEY WAY) SWB5-10673 & UP
HUB ADAPTER (W/ 1/4" KEY WAY) SWB6-10169 & UP
KNIFE DRIVE STUD ASY.
3
4*
5
SOCKET HEAD CAPSCREW, (TORQUE TO 35 FT. LBS)
SUPPORT HORIZONTAL KNIFE DRIVE
HEX BOLT
6
NOTE:TORQUE BOLTS ITEM #4 TO 35 FT. LBS.
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -25
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD PUMP ASY - PN 02974302 (SN 10361 09-04 & DOWN)
ITEM PART NO. QTY.
DESCRIPTION
02974302
02976923
02976922
02976921
02976920
02976919
02976918
02976917
02976916
02976915
02976914
02976913
02976912
02976911
02976924
1
1
1
1
1
1
1
1
4
2
2
1
4
4
1
PUMP ASY, 1.16/0.49 CID/REV (STEEL MOUNTING FLANGE & END CAP)
1
CONNECTING SHAFT
GEAR SET
2
3
GEAR SET
4
END CAP (STEEL END CAP)
MOUNTING FLANGE (STEEL MOUNTING FLANGE)
GEAR HOUSING
5
6
7
GEAR HOUSING
8
HOUSING TIE BOLT
DOWEL PIN
9
10
11
12
13
*
DOWEL PIN
MID SPACER PLATE
THRUST BLOCK
WASHER
SEAL KIT ( INCLUDES ITEMS W / * )
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -26
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD PUMP ASY - PN 02974302A (SN 10362 10-04 TO 10770)
ITEM PART NO. QTY.
DESCRIPTION
02974302A
02980846
02980847
02980848
02976913
02980849
--------------
02980850
02980851
02980852
02980853
--------------
02980856
02980857
-------------
02976911
02980854
02980855
--------------
02976915
02976914
02976923
02980858
1
1
1
1
1
1
4
1
1
1
1
1
1
4
4
4
4
4
4
2
2
1
1
PUMP ASY, 1.16/0.49 CID/REV (ALUMINUM MOUNTING FLANGE & END CAP)
MOUNTING FLANGE, (ALUMINUM MOUNTING FLANGE)
END CAP, (ALUMINUM END CAP)
HOUSING, (F/ LARGE GEAR SECTION)
MID SECTION SPACER PLATE
1
2
3
4
5
HOUSING, (F/ SMALL GEAR SECTION)
SEAL, BACK UP (INCLUDED N SEAL KIT)
DRIVE GEAR, (LARGE GEAR)
6
7
8
DRIVEN GEAR, (LARGE GEAR)
DRIVE GEAR, (SMALL GEAR)
9
10
11
12
13
14
15
16
17
18
19
20
21
22
DRIVEN GEAR, (SMALL GEAR)
SHAFT SEAL, (INCLUDED IN SEAL KIT)
SNAP RING
THRUST BLOCK, (F/ LARGE OR SMALL GEAR SECTION)
CHANNEL SEAL, (INCLUDED IN SEAL KIT)
WASHER
FASTENER, (173MM)
NUT
SECTIONAL SEAL, (INCLUDED IN SEAL KIT)
PIN, DOWEL, (SHORT PIN)
PIN, DOWEL, (LONG PIN)
CONNECTING, SHAFT
SEAL KIT, (F/ LARGE GEAR SECTION)
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -27
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD PUMP ASY - PN 02974302A (SN 10362 10-04 TO 10770)
Continued...
ITEM PART NO. QTY.
DESCRIPTION
23
02980859
1
SEAL KIT, (F/ SMALL GEAR SECTION)
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -28
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD PUMP ASY - PN 02974302B (SN 10771 09-08 & UP)
ITEM PART NO. QTY.
DESCRIPTION
PUMP TANDEM GEAR 1.16/.50 CID
PUMP FLANGE
02974302B
02985005
02985006
02988046
02988047
02988048
02988049
02988050
02988051
02985014
02985015
02985016
02985017
02988051
02985018
1
1
1
4
1
1
1
1
1
1
1
1
8
1
1
1
2
REAR COVER
3
THRUST PLATE
4
DRIVE GEAR
5
SHAFT, DRIVE GEAR
DRIVEN GEAR
6
7
SHAFT, DRIVEN GEAR
KIT, M10 BOLT & WASHER, 4 EA.
RETAINING RING
8
9
10
11
12
MID-PLATE SPACER
SPLINED CONNECTING SHAFT
PIN, DOWEL
BOLTS AND WASHERS KIT
SEAL KIT
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -29
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE INTENTIONAL LEFT BLANK
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -30
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD PUMP ASY - TANDEM PN 02974303B
ITEM PART NO. QTY.
DESCRIPTION
02974303B
02985003
02985004
02985005
02985006
02985007
02985008
02985009
02985010
02985011
02985012
02985013
02985017
02985015
02985014
1
1
1
1
1
4
1
1
1
1
4
4
8
1
1
TANDEM PUMP ASSEMBLY
BODY, (.38 CID SECTION)
BODY, (.98 CID SECTION)
PUMP FLANGE
1
2
3
4
REAP COVER
5
THRUST PLATE (NOT INCLUDED IN SEAL KIT)
DRIVE GEAR, (.38 CID SECTION)
DRIVE GEAR, (.98 CID SECTION)
DRIVEN GEAR, (.38 CID SECTION)
DRIVEN GEAR, (.98 CID SECTION)
BOLT, HEX HEAD M10 X 165MM
WASHER, M10
6
7
8
9
10
11
12
13
14
DOWEL PIN
MID PLATE SPACER
RETAINING RING
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -31
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD PUMP ASY - TANDEM PN 02974303B
Continued...
ITEM PART NO. QTY.
DESCRIPTION
15
02985016
1
SPLINED CONNECTING SHAFT
16
02985018
1
SEAL KIT
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -32
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD SCHEMATIC - SINGLE WG
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -33
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD SCHEMATIC - SINGLE WG
Continued...
ITEM PART NO. QTY.
DESCRIPTION
1
02974302
02974303
02981705
02974309
02974312
02988789
02981527
0693400A
0693500A
02982296
02965521
00751003
02823100
00016200
00750940
02982478
02981979
02974301
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
PUMP TANDEM GEAR, 1.16/0.49 CID
PUMP TANDEM GEAR, 0.98/0.37 CID
HYDRAULIC TANK ASY. ( NCLUDES NEXT 4 ITEMS )
FILTER ASY.
2
SUCTION STRAINER
CONTROL VALVE SOLENOID
TANK WLDMT
3
4
5
CURB STOP CYLINDER ASY
BAR LIFT CYLINDER ASY
BREAK-A-WAY VALVE ASY ( CONSIST OF THE FOLLOWING 6 ITEMS )
VALVE BODY ONLY
PIPE PLUG
HYD. ADAPTER ELBOW
BOLT
LOCKNUT
RELIEF CARTRIDGE ( 1550 PSI SETTING )
ROTARY ACTUATOR ASY.
MOTOR, 2.8 CID
6
7
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -34
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD TANK ASY - PN 02981705
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -35
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD TANK ASY - PN 02981705
Continued...
ITEM PART NO. QTY.
DESCRIPTION
02981705
00017000
001891
1
8
1
3
2
1
5
1
1
1
1
1
1
1
1
1
1
8
2
1
1
2
2
3
3
1
1
1
ASSEMBLY HYDRAULIC TANK
LOCKWASHER 1/4 PL STD
ADP HYD ELBOW 4MP-6MJ90
ADP HYD STGHT 8MJ-8MB
HHCS 5/16 NC 1 PL5
1
2
3
00696800
10119000
0117100
4
5
MAGNETIC DRAIN PLUG
NUT TOPLOCK 1/4 NC PLB
ADP HYD ELBOW 8MB-8MJ 90
GAUGE SIGHT TEMPERATURE
VALVE SOLENOID CONTROL
FILTER HOUSING W/FILTER GUAGE
SUCTION STRAINER
6
02959924
02962213
02968880
02988789
02974309
02974312
02974320
02981527
02974369
02974370
064600D
00002100
10074000
02974997
000752
7
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
HOSE #8-8FJX-8FJX-15LG "
WELDMENT HYDRAULIC TANK
COVER TANK ACCESS
ADP HYD ELBOW SPCL 8MJ-12MB 90 W/4FP
COVER GASKET
HHCS 1/4 NC 1/2 PL5
HHCS 1/4 NC 3 PL5
DECAL,NAME SWITCH BLADE
ELBOW 2MP-2FP 90
000752
SEAL WASHER 1/4
00011700
00024100
10058000
00776031
02974374CA
02977417
5/16 LOCKWASHER
1/4 FLATWASHER
HHCS 1/4 NC 1 PL5
CANISTER, PARTS MANUAL
MANUAL OPERATORS, SWITCH BLADE
DECAL, OPERTOR`S MANUAL INSIDE
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -36
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD VALVE ASY W-FITTINGS - PN 02982077
ITEM PART NO. QTY.
DESCRIPTION
02982077
02974306
02968850
03200284
02965166
02981896
1
1
2
2
2
2
VALVE ASY, W/ FITTINGS ( 2-SPOOL )
VALVE, DIRECTIONAL CONTROL
HYD. ADAPTER STRAIGHT
HYD. ADAPTER STRAIGHT
HYD. TEE ADAPTER
1
2
3
4
5
HYD. ADAPTER
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -37
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE INTENTIONAL LEFT BLANK
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -38
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD VALVE ASY W-O FITTINGS - PN 02974306
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -39
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD VALVE ASY W-O FITTINGS - PN 02974306
Continued...
ITEM PART NO. QTY.
DESCRIPTION
VALVE ASY, 2 SPOOL W/O FITTINGS
UNLOAD PLUNGER
POPPET ASY.
SPACER
02974306
02976934
02966645
02966646
02976933
02966648
02966649
02966650
02966651
02966652
02966653
02966654
02976932
02976931
02976930
02966657
02966658
02966659
02966660
02966661
02966662
02976946
02976945
02966669
02976944
02976943
02976942
02976941
02976940
02976939
02976938
02976937
02976936
02976935
02966671
02976957
1
2
2
1
2
4
2
2
2
2
1
1
1
1
1
4
2
1
1
1
1
1
1
1
2
1
1
3
1
1
1
1
1
1
2
2
1
2
3
4
SPOOL
5
SEAT ASY.
PLUG ASY.
PLUG ASY.
BUSHING
6
7
8
9
LOCKOUT SPRING
CAP ASY.
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
PLUG ASY.
BODY
POPPET
SEAT
O-RING
RETAINING RING
WASHER
WASHER
WASHER
WASHER
CAP ASY.
SPRING
SPRING
PLUG ASY.
WASHER
WASHER
BALL
SPRING
SPRING
CONE
SPACER
ADAPTER CAP
WASHER
WIPER SEAL
HANDLE KIT
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -40
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD VALVE REMOTE CONTROL CABLES
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -41
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD VALVE REMOTE CONTROL CABLES
Continued...
ITEM PART NO. QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
00015800
2
2
2
3
2
2
2
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
6
3
1
LOCKNUT
000354
BOLT
001636
BOLT
00750940
02959924
02966687
02966688
02968698
02971200
02971201
02971202
02971203
02974296
02974299
02974323
02964028
02982367
02982366
02982365
02964318
02974321
02974322
02982077
02974962
00023500
02733700
02975270
LOCKNUT
LOCKNUT
ADJUSTING YOKE END
CLEVIS PIN
COTTER PIN
CABLE, REMOTE CONTROL - 48" LG
CABLE, REMOTE CONTROL - 60" LG
CABLE, REMOTE CONTROL - 72" LG
CABLE, REMOTE CONTROL - 102" LG
SWITCH MOUNT WLD’MT
ANGLE, MOUNT
10
11
12
13
14
ANGLED SINGLE AXIS CONTROL ASY.
SWITCH, PUSH PULL ( W/ ITEMS 14 )
KNOB ( REPLACEMENT KNOB F/ ITEM # 13 )
JAM NUT ( REPLACEMENT F/ ITEM # 13 )
NUT ( REPLACEMNT F/ ITEM # 13 )
RELIEF VALVE ( SET @ 2500 PSI )
DECAL INSTRUCT VALVE & SWITCH
3 - POSITION TOGGLE SWITCH
VALVE ASY, W/ FITTINGS
BOOT, TOGGLE SWITCH COVER
FLATWASHER
15
16
17
18
19
20
21
22
BOLT
DECAL INSTRUCTIONS, REVERSING SWITCH
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -42
Download from Www.Somanuals.com. All Manuals Search And Download.
HYD VALVE SOLENOID ASY - PN 02988789
ITEM PART NO. QTY.
DESCRIPTION
02988789
02979345
02979346
02979190
02989041
02988802
02988803
02988804
*
1
1
1
1
1
1
1
1
1
1
1
VALVE SOLENOID ASY.
1
2
3
4
5
6
7
*
BODY
RELIEF CARTRIDGE
BOLT KIT
*SOLENOID ASY.
STEM TUBE ASY.
COIL SOLENOID
COIL NUT
CONSISTS OF REPLACEMENT PARTS - STEM TUBE, COIL SOLENOID, COIL NUT
SEAL KIT (NOT SHOWN)
02988805
02979191
SEAL KIT/RELIEF CARTRIDGE (NOT SHOWN)
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -43
Download from Www.Somanuals.com. All Manuals Search And Download.
KNIFE BAR - 5 FT RH WG - PN 02974361 - W/ SERRATED KNIVES
ITEM PART NO. QTY.
DESCRIPTION
02974361
02982752
0189900
1
5’ CUTTER BAR, ASY, SERRATED KNIFE
SERRATED KNIFE SECTION
KNIFE PROTECTOR,CARDBOARD 63"
INSERT NYLON DRIVE BRG CLAMP
KNIFE HEAD WLD’MT
BOLT
1
2
3
4
21
1
02974316
02974349
00756328
02976270
02976271
02976272
0530100M
1
1
1
5
6
7
8
35
7
SECTION BOLT
HEAD BOLT
42
1
LOCKNUT
BACKING STRIP 5’
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -44
Download from Www.Somanuals.com. All Manuals Search And Download.
KNIFE BAR - 6 FT RH WG - PN 02974373 - W/ SERRATED KNIVES
ITEM PART NO. QTY.
DESCRIPTION
02974373
02982752
0687800
1
ASSEMBLY 6`SERR KNIFE BAR
KNIFE SECTION TOP SER CHRM PLT
ANGLE, BOARD 84"
1
2
3
4
5
6
7
8
25
1
02974316
02974349
02976270
02976271
02976272
0531900
1
INSERT NYLON DRIVE BRG CLAMP
WELDMENT KNIFE HEAD
SECTION BOLT 5/8 LONG
HEAD BOLT 1-1/64 LONG
SECTION LOCKNUT (CONE)
BACKING STRIP 6`
1
43
7
50
1
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -45
Download from Www.Somanuals.com. All Manuals Search And Download.
KNIFE BAR - 5 FT LH WG - PN 02977716 - W/ SERRATED KNIVES
ITEM PART NO. QTY.
DESCRIPTION
02977716
02982752
0189900
1
5’ KNIFE BAR ASY, LH WING
SERRATED KNIFE SECTION
KNIFE PROTECTOR, CARDBOARD 63"
INSERT NYLON DRIVE BRG CLAMP
KNIFE HEAD WLD’MT
BOLT
1
2
3
4
21
1
02974316
02974349
00756328
02976270
02976271
02976272
0530100M
1
1
1
5
6
7
8
35
7
SECTION BOLT
HEAD BOLT
42
1
LOCKNUT
BACKING STRIP, 5’
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -46
Download from Www.Somanuals.com. All Manuals Search And Download.
KNIFE BAR - 6 FT LH WG - PN 02977718 - W/ SERRATED KNIVES
ITEM PART NO. QTY.
DESCRIPTION
02977718
02982752
0189900
1
6’ KNIFE BAR ASY, LH WING
SERRATED KNIFE SECTION
KNIFE PROTECTOR, CARDBOARD 63"
INSERT NYLON DRIVE BRG CLAMP
KNIFE HEAD WLD’MT
BOLT
1
2
3
4
25
1
02974316
02974349
00756328
02976270
02976271
1
1
1
5
6
43
7
SECTION BOLT
HEAD BOLT
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -47
Download from Www.Somanuals.com. All Manuals Search And Download.
KNIFE BAR - 6 FT LH WG - PN 02977718 - W/ SERRATED KNIVES
Continued...
ITEM PART NO. QTY.
DESCRIPTION
LOCKNUT
7
02976272
50
8
0531900
1
BACKING STRIP, 6’
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -48
Download from Www.Somanuals.com. All Manuals Search And Download.
SHOE & BRK-A-WAY PRE-ASY RH MOUNT - PN 02975986
ITEM PART NO. QTY.
DESCRIPTION
SHOE & BRK-A-WAY PRE-ASY RH MOUNT
FLATWASHER
02975986
00011100
03101646
00002000
03200250
02974363
00019600
00019300
1
1
1
1
1
6
1
1
1
2
3
5
6
7
8
LOCKWASHER
BOLT
RUBBER BUMPER PAD
WASHER
LOCKWASHER
BOLT
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -49
Download from Www.Somanuals.com. All Manuals Search And Download.
SHOE & BRK-A-WAY PRE-ASY RH MOUNT - PN 02975986
Continued...
NOTE:THIS ITEM IS SPRING LOADED AT THE FACTORY. ALL OTHER PARTS NOT LISTED ARE NOT AVAILABLE FOR INDIVIDUAL SALE. DO NOT
ATTEMPT TO REMOVE ANY PART FROM THIS ASSEMBLY OTHER THAN THE SHOWN LISTED PARTS.
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -50
Download from Www.Somanuals.com. All Manuals Search And Download.
SHOE & BRK-A-WAY PRE-ASY LH MOUNT - PN 02977726
ITEM PART NO. QTY.
DESCRIPTION
SHOE & BRK-A-WAY PRE-ASY LH MOUNT
FLATWASHER
02977726
00011100
03101646
00002000
03200250
02974363
00019600
00019300
1
1
1
1
1
6
1
1
1
2
3
5
6
7
8
LOCKWASHER
BOLT
RUBBER BUMPER PAD
WASHER
LOCKWASHER
BOLT
NOTE:THIS ITEM IS SPRING LOADED AT THE FACTORY. ALL OTHER PARTS NOT LISTED ARE NOT AVAILABLE FOR INDIVIDUAL SALE. DO NOT
ATTEMPT TO REMOVE ANY PART FROM THIS ASSEMBLY OTHER THAN THE SHOWN LISTED PARTS.
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -51
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE INTENTIONAL LEFT BLANK
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -52
Download from Www.Somanuals.com. All Manuals Search And Download.
SHOE, DRIVE & BRK-A-WAY ASY RH MOUNT - PN 02975194
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -53
Download from Www.Somanuals.com. All Manuals Search And Download.
SHOE, DRIVE & BRK-A-WAY ASY RH MOUNT - PN 02975194
Continued...
ITEM PART NO. QTY.
DESCRIPTION
02975194
00000200
00001200
00001800
00002701
00011100
00015800
5C8130
1
5
1
8
2
2
2
1
3
2
2
1
1
2
1
1
2
3
3
1
1
4
4
1
2
1
2
ASY SHOE DRIVE SPRING BRKWY
1
NUT 3/4 NC HEX PL
2
NUT 1/2 NC HEX PL
3
LOCKNUT TLM 1/2 NC PLB
FLATWASHER,3/4,TYPE AW,ZP
FLATWASHER STD 3/8
LOCKNUT TLM 3/8-NC PLC
HEXNUT 1/2 JAM ZP
5
6
7
8
9
000206
NO. 2 RED LUBRICAPS<
TUBE 1-1/4 OD X 9/16 ID X3-3/4
HHCS 1/2-13UNC 1-3/4 PL5
SOLE SKID SHOE
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
02974343
00749130
02974344
00752670
00753642
02974354
02974358
02042300
02931300
02972570
02974300A
02974301A
02976853
02976854
02974313
02974342
02975986
02988071
FITTING,GREASE STRAIGHT 1/4-28
HEXB
3/8 NC X 1-1/4 PL5
SPACER CUTTER BAR
ROD DEFLECTOR
ADP HYD STGHT 10MB-8MJ
HHCS,3/4NC X 2,ZP,GRD5
LOCKWASHER 3/4 PL STD
ASY HORIZ KNIFE DRV 1"X1/4"KEY
MOTOR GEROTOR 2.8CID 1"X1/4"KY
PLOW BOLT #3 1/2 NC 2-1/2 PL8
PLOW BOLT #3 1/2 NC
7
PL8
BRACKET HYDRAULIC MOTOR ADAPTR
TUBE 1-1/4 OD X 9/16 ID X4-5/8
PREASY SKIDSHOE & BREAKAWAY
FLANGE NUT, 1/2" NC
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -54
Download from Www.Somanuals.com. All Manuals Search And Download.
SHOE, DRIVE & BRK-A-WAY ASY LH MOUNT - PN 02977727
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -55
Download from Www.Somanuals.com. All Manuals Search And Download.
SHOE, DRIVE & BRK-A-WAY ASY LH MOUNT - PN 02977727
Continued...
ITEM PART NO. QTY.
DESCRIPTION
02977727
00000200
00001200
00001800
00002701
00011100
00015800
5C8130
1
5
1
8
2
2
2
1
3
2
2
1
1
2
1
1
2
3
3
1
1
4
4
1
2
1
2
ASY LH SHOE DRIVE SPRING BRKWY
1
NUT 3/4 NC HEX PL
2
NUT 1/2 NC HEX PL
3
LOCKNUT TLM 1/2 NC PLB
FLATWASHER,3/4,TYPE AW,ZP
FLATWASHER STD 3/8
LOCKNUT TLM 3/8-NC PLC
HEXNUT 1/2 JAM ZP
5
6
7
8
9
000206
NO. 2 RED LUBRICAPS<
TUBE 1-1/4 OD X 9/16 ID X3-3/4
HHCS 1/2-13UNC 1-3/4 PL5
SOLE SKID SHOE
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
02974343
00749130
02974344
00752670
00753642
02974354
02977740
02042300
02931300
02972570
02974300A
02974301A
02976853
02976854
02974313
02974342
02977726
02988071
FITTING,GREASE STRAIGHT 1/4-28
HEXB
3/8 NC X 1-1/4 PL5
SPACER CUTTER BAR
ROD LH DEFLECTOR
ADP HYD STGHT 10MB-8MJ
HHCS,3/4NC X 2,ZP,GRD5
LOCKWASHER 3/4 PL STD
ASY HORIZ KNIFE DRV 1"X1/4"KEY
MOTOR GEROTOR 2.8CID 1"X1/4"KY
PLOW BOLT #3 1/2 NC 2-1/2 PL8
PLOW BOLT #3 1/2 NC
7
PL8
BRACKET HYDRAULIC MOTOR ADAPTR
TUBE 1-1/4 OD X 9/16 ID X4-5/8
PREASY LH SKID SHOE & BREAKAWY
FLANGE NUT, 1/2" NC
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -56
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING HARNESS - DUAL WG - PN 02977754
ITEM PART NO. QTY.
DESCRIPTION
02977754
1
WIRE HARNESS LH DUAL WING
2
02965731
1
FUSE 10 AMP, TYPE ATO
NOTE:TOGGLE SWITCH IS SHOWN FOR ILLUSTRATION ONLY AND IS NOT INCLUDED WITH WIRE HARNESS. THIS WIRE HARNESS IS ONLY USED
WHEN LH WING IS MOUNTED. IT DOES NOT REPLACE THE RH HARNESS BUT IS USED WITH IT.
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -57
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING HARNESS - SINGLE WG - PN 02974318
ITEM PART NO. QTY.
DESCRIPTION
02974318
1
2
1
WIRE HARNESS SINGLE WING
CONNECTOR, COIL-HRSCHMANN TYPE
FUSE 10 AMP, TYPE ATO
1
2
002504
02965731
NOTE:THIS WIRE HARNESS IS USED WITH A RH WING MOWER, WIRE HARNESS WILL NOT INCLUDE PUSH PULL SWITCH OR TOGGLE SWITCH. IF
LH WING IS USED THIS WIRE HARNESS WILL STILL BE USED AND THE LH WING HARNESS WILL ALSO BE USED.
Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11
©2011 Alamo Group Inc.
Parts Section -58
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
TO THE OWNER/OPERATOR/DEALER
To keep your implement running efficiently and safely, read your manuals thoroughly and follow these directions and
the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the
information you need.
The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of
tractor operators:
REQUIRED OF THE OWNER
1. Provide a Roll-Over-Protective Structure that meets the requirements of this standard.
2. Provide seat belts that meet the requirements of this paragraph of this standard and SAE J4C.
3. Ensure that each employee uses such seat belt while the tractor is moving.
4. Ensure that each employee tightens the seat belt sufficiently to confine the employee to the
protected area provided by the ROPS.
REQUIRED OF THE OPERATOR
1. Securely fasten seat belt if the tractor has a ROPS.
2. Where possible, avoid operating the tractor near ditches, embankments, and holes.
3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.
4. Stay off slopes too steep for safe operation.
5. Watch where you are going, especially at row ends, on roads, and around trees.
6. Do not permit others to ride.
7. Operate the tractor smoothly, no jerky turns, starts, or stops.
8. Hitch only to the draw bar and hitch points recommended by the tractor manufacturer.
9. When the tractor is stopped, set brakes securely and use park lock, if available.
Keep children away from danger all day, every day...
Equip tractors with rollover protection (ROPS) and keep all machinery guards
in place...
Please work, drive, play and live each day with care and concern for your safety
and that of your family and fellow citizens.
Download from Www.Somanuals.com. All Manuals Search And Download.
ALAMO INDUSTRIAL
Limited Warranty
1. Limited Warranties
1.01. Alamo industrial warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser
(“purchaser”) and warrants for six months to the original commercial or industrial purchaser (“purchaser”) that the goods purchased
are free from defects in material or workmanship.
1.02. Manufacturer will replace for the purchaser any part or parts found, upon examination at one of its factories, to be defective under
normal use and service due to defects in material or workmanship.
1.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence,
alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served
its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades,
shields, guards, or pneumatic tires except as specifically found in your operator’s manual.
1.04. Except as provided herein, no employee, agent, dealer, or other person is authorized to give any warranties of any nature on behalf
of manufacturer.
2. Remedies And Procedures
2.01. This limited warranty is not effective unless the purchaser returns the registration and warranty form to manufacturer within 30 days of
purchase.
2.02. Purchaser claims must be made in writing to the authorized dealer (“dealer”) from whom purchaser purchased the goods or an approved
authorized dealer (“dealer”) within 30 days after purchaser learns of the facts on which the claim is based.
2.03. Purchaser is responsible for returning the goods in question to the dealer.
2.04. If after examining the goods and/or parts in question, manufacturer finds them to be defective under normal use and service due to
defects in material or workmanship, manufacturer will:
(A) repair or replace the defective goods or part(s) or
(B) reimburse purchaser for the cost of the part(s) and reasonable labor charges (as determined by manufacturer) if purchaser
paid for the repair and/or replacement prior to the final determination of applicability of the warranty by manufacturer. The choice of
remedy shall belong to manufacturer.
2.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by manufacturer and for returning the
goods to the dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s)
from the dealer to the designated factory.
3. Limitation Of Liability
3.01. Manufacturer disclaims any express (except as set forth herein) and implied warranties with respect to the goods including, but not
limited to, merchantability and fitness for a particular purpose.
3.02. Manufacturer makes no warranty as to the design, capability, capacity, or suitability for use of the goods.
3.03. Except as provided herein, manufacturer shall have no liability or responsibility to purchaser or any other person or entity with respect
to any liability, loss, or damage caused or alleged to be caused directly or indirectly by the goods including, but not limited to, any
indirect, special, consequential, or incidental damages resulting from the use or operation of the goods or any breach of this warranty.
Not withstanding the above limitations and warranties, manufacturer’s liability hereunder for damages incurred by purchaser or others
shall not exceed the price of the goods.
3.04. No action arising out of any claimed breach of this warranty or transactions under this warranty may be brought more than two (2)
years after the cause of action has occurred.
4. Miscellaneous
4.01. Proper venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe county, Texas.
4.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be
a waiver of any other term.
4.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such
provision shall not invalidate any other provisions herein.
4.04. Applicable law may provide rights and benefits to purchaser in addition to those provided herein.
Keep for your records
Attention: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification
when applying for warranty.
Alamo Industrial Implement Model ____________________________ Serial Number ________________________________
Date Purchased __________________________________________ Dealer ______________________________________
Attention:
Read your operator’s manual
ALAMO INDUSTRIAL
1502 E. Walnut
Seguin, Texas 78155
830-379-1480
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch Blade 5 ft. & 6 ft (02/05)
P/N 02974374P
Download from Www.Somanuals.com. All Manuals Search And Download.
|