All-Flex Mower
AFM4011 And AFM40133
16683
315-470P
Parts Manual
Read the Operator's manual entirely. When
you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception.Your life and the lives of
others depend on it!
© Copyright 2008 Printed 04/02/08
Cover photo may show optional equipment not
supplied with standard unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
Alphabetized Table of Contents
B
H
L
P
R
S
T
C
D
F
G
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Frame
Land Pride
Center Deck Pivot
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg14474
Drawing Image Number
1.
2.
3.
4.
5.
5.
6.
7.
8.
9.
810-005C
800-080C
807-026C
804-025C
315-175H
315-144H
805-228C
315-136H
803-007C
315-487D
CYL 2X8X1.12 ROD SINGLE ACTING
GREASE ZERK 1/4-28 THD FORMING
PIVOT STOP SPRING
WASHER FLAT 3/4 SAE PLT
DECK LOCK-UP LATCH
REAR LOCK-UP LATCH AFM133
PIN CLEVIS 3/4 X 3 3/4 USEABLE
REAR DECK PIVOT TUBE AFM133
NUT LOCK 1/4-20 PLT
REAR DECK CYL LUG PIN
HHCS 1/4-20X2 GR5
REAR DECK CYL LUG WELD
HHCS 1/2-13X1 1/2 GR5
WASHER LOCK SPRING 1/2 PLT
GREASE ZERK STRAIGHT 1/4-28
PUSH, PIVOT TUBE HALF CLAMP
PIVOT TUBE WEAR PAD
WASHER FLAT 1/2 SAE PLT
PIN COTTER 5/32 X 1 1/4 LG
PIN CLEVIS 1 X 2 3/4 USABLE LG
PIN ROLL 3/16X1 1/4 PLT
(S/N 129748+)
(S/N 129747-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
10. 802-152C
11. 315-183H
12. 802-091C
13. 804-015C
14. 800-001C
15. 175-061D
16. 175-060D
17. 804-016C
18. 805-045C
19. 805-004C
20. 805-023C
20. 805-088C
S/N ______+
S/N ______-
PIN, HAIR COTTER 3/16 WIRE DIA
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Frame
Land Pride
Pull Latch Cord Lock-Up
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg12691
Drawing Image Number
1.
890-337C
CORD-PARACHUTE 3/16 DIA.
Right hand 30" Long; Left hand 30"
Long and Center 30" Long. Frame to
Tractor 120" Long. Total Length 18
Ft. Sold only in 12" increments
2.
3.
4.
890-589C
890-332C
315-166S
5/32 I.D. OVAL SLEEVE
WELDED RING 1/4 X 2
DECK LATCH PULL ROPE ASSEMBLY
NOTE:
When Installing Cord to Deck Latchs Be Sure to
Apply Tension to Cord For Poper Operation.
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Frame
Land Pride
Right Hand and Left Hand Deck Pivot
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg12647
Drawing Image Number
1.
2.
3.
4.
5.
6.
7.
8.
9.
315-153A
315-155A
315-486D
802-152C
803-007C
800-136C
890-331C
315-134H
807-026C
AFM133 L.H. DECK ASSY
AFM133 R.H. DECK ASSY
TOOLBAR PIN
HHCS 1/4-20X2 GR5
NUT LOCK 1/4-20 PLT
ZERK 1/4-28 X 45 DEG SELF-TAP
BUSHING 1 X 3/4 X 1
R.H. TOOLBAR AFM133
PIVOT STOP SPRING
10. 805-142C
11. 315-142H
12. 800-080C
13. 890-005C
14. 315-137H
15. 810-150C
16. 315-135H
17. 315-485D
18. 804-025C
19. 805-045C
20. 802-204C
21. 803-026C
22. 802-370C
PIN CLEVIS 3/4 X 3 1/2 PLT
DECK LOCK-UP LATCH AFM133
GREASE ZERK 1/4-28 THD FORMING
BUSHING CYL 1 1/4 X 1 X 1
WING CYL FLEX LUG AFM133
CYL 2.5X12X1.25 ROD (TIE ROD)
L.H. TOOLBAR AFM133
WING CYLINDER LUG PIN
WASHER FLAT 3/4 SAE PLT
PIN COTTER 5/32 X 1 1/4 LG
HHCS 3/4-10X3 3/4 GR5
NUT LOCK 3/4-10 PLT
(S/N 176350+)
(S/N 176350+)
(S/N 176350+)
(S/N 176349-)
(S/N 176349-)
HHCS 1/4-20X1 3/4 GR5
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Frame
Land Pride
Transport Frame
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg13785
Drawing Image Number
1.
315-449H
AFM4011 TRANSPORT FRAME
(S/N 289110+)
Rev. 3 not compat. w/Rev. 2;
Rev. 4
2.
3.
315-277H
315-147H
RPBY 315-458S 133 FRAME
RPBY 315-445A
(S/N 176350 Ö 289109)
For S/N 176349-order with items 6
through 13.
Rev. 2 not compat. w/Rev. 1
Rev. 1
4.
5.
6.
7.
8.
9.
890-118C
805-109C
804-016C
803-027C
804-023C
401-372D
SCREW JACK 2000#
PIN COTTER 1/8 X 1 1/4 PLT
WASHER FLAT 1/2 SAE PLT
NUT HEX 3/4-10 PLT
WASHER LOCK SPRING 3/4 PLT
WASHER, SAFETY CHAIN
FRONT HITCH LUG WELDMENT
RPBY 315-274H
PIN HITCH 3/4 X 4 3/8
HHCS 3/4-10X7 GR5
HHCS 3/4-10X6 1/2
FRONT P.T.O. MOUNT
10. 315-274H
11. 315-197H
12. 805-081C
13. 802-095C
14. 802-360C
15. 315-139H
16. 890-182C
(S/N 176350+)
(S/N 176349-)
Rev. 2
Rev 1; Use up stock
SAFETY CHAIN 10000 LB
When Ording New Chain Also Order
401-472D
17. 803-031C
18. 804-027C
19. 804-028C
20. 315-004H
21. 802-075C
22. 802-074C
23. 802-205C
24. 803-038C
25. 315-754D
26. 803-148C
27. 315-369H
28. 315-753D
29. 802-235C
30. 802-060C
31. 804-019C
32. 315-768D
33. 802-114C
34. 803-013C
35. 315-452E
36. 315-453E
37. 315-459A
NUT HEX 1-8 PLT
(S/N 153376-)
(S/N 153376-)
(S/N 153376-)
(S/N 153376-)
(S/N 153376-)
(S/N 153376-)
WASHER LOCK SPRING 1 PLT
WASHER FLAT 1 USS PLT
TRANSPORT HITCH LUG
HHCS 1-8X7 GR5
HHCS 1-8X6 1/2 GR5
HHCS 1-8X5 1/2 GR5
NUT HEX 1-8 NYLON INSERT PLT
BALL SWIVEL MOUNT BOTTOM PLATE
NUT HEX NYLOCK 5/8-11 PLT
BALL SWIVEL MOUNT PLATE
HITCH SPACER TUBE
HHCS 1-8X5 GR5
HHCS 5/8-11X4 GR5
WASHER FLAT 5/8 USS PLT
SPINDLE 1in
HHCS 3/8-16X2 1/2 GR5
NUT LOCK 3/8-16 PLT
AFM4011 RH BOLTIN SPIN. ARM
AFM4011 LH BOLTIN SPIN. ARM
4011 BOLT-IN SPIN SHIPOUT
(S/N 289110+)
(S/N 289110+)
(S/N 289110+)
(S/N 289108-)
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Frame
Land Pride
Transport Frame Tire and Hub
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg12645
Drawing Image Number
1.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10-097
518081
492107
TR-412
803-159C
890-614C
805-045C
803-053C
804-025C
822-030C
CARLISLE TIRE 18 X 9.5-8 4PLY
RP BY 10-097
CARLISLE RIM FOR 18X9.5-8 TIRE
T1. VALVE MARTIN
NUT LUG 1/2-20 X 60 DEG PLT
GREASE CAP #1505
PIN COTTER 5/32 X 1 1/4 LG
NUT HEX SLOTTED 3/4-16
WASHER FLAT 3/4 SAE PLT
BEARING CONE 1
Rev. 2
Rev 1; Use up stock
10. 822-080C
11. 815-104C
11. 815-001C
12. 802-125C
13. 816-014C
14. 800-001C
15. 814-118C
BEARING CUP L44610
HUB 4-BOLT W/ZERK COMPLETE
TINE GW HUB W/O ZERK COMPLETE
BHSNB 1/2-20X1 3/8 GR5
TINE GAUGE WHEEL HUB SEAL
GREASE ZERK STRAIGHT 1/4-28
TIRE & WHL ASSY 18X9.50-8 4PLY
(S/N 216927+) With zerk
(S/N 216926-) Without zerk
(S/N 216927+)
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Drivelines
Land Pride
Driveline Arrangement
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg12653
Drawing Image Number
1.
2.
3.
3.
3.
4.
5.
6.
7.
8.
802-458C
804-015C
826-274C
826-097C
826-124C
826-125C
826-126C
315-145H
802-444C
826-127C
HHCS M12X1.75X30 GR8.8
WASHER LOCK SPRING 1/2 PLT
GBOX DIVIDER OMNI 250559 1:1
RPBY 315-447A
4-WAY SPLITTER BOX 1:1 RATIO
PTO CV 2380 X 41.73
PTO 2200 X 19.09 W/CLUTCH
SPLITTER BOX COVER AFM133
HHCS M12X1.75X50 GR8.8
PTO 2200 X 23.23 W/CLUTCH
(S/N 272760+)
(S/N 125861 <-> 272759)
(S/N 125860-)
Rev. 3 not compat. w/Rev. 2
Rev. 2 not compat. w/Rev. 1
Rev. 1
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Drivelines
Land Pride
Driveline Center Deck (826-127C) Walterscheid
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg12887
826-127C
Drawing Image Number
PTO 2200 X 23.23 W/CLUTCH
WS FRICTION CLUTCH
WALTSCHEID CROSS & BRG KIT
WS SPRING PIN
1.
2.
3.
4.
5.
6.
7.
8.
9.
9.
053313
044439
020614
041065
048755
390002
377234
377240
392045
389965
WS INBOARD YOKE
WS INNER PROFILE OV
WS OUTER PROFILE &
WS SHIELD CONE-4 RIB
WS SHIELD CONE-10RIB
WS OUTER SHIELD OVL.
RPBY 392045
(S/N 259230+)
(S/N 259229-)
(S/N 259230+)
(S/N 259229-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
Rev. 2 not compat. w/Rev. 1
Rev. 1
10. 392046
10. 384488
11. 087279
12. 044321
13. 365305
14. 818-552C
15. 818-540C
16. 196837
16. 380905
17. 390404
17. 381908
18. 818-450C
19. 380371
20. 355154
WS INNER SHIELD RND.
RPBY 392046
WS BEARING RING
DRIVELINE SHIELD SAFETY CHAIN
WS SCREW
DECAL DANGER PTO DRIVELINE
DECAL DANGER GUARD MISS PTO
WS ASGE YOKE 1 3/8-6 SPL.
RPBY 196837
WS ASGE COLLAR KIT
(RPBY 390404)WS QCK DSCNCT KIT
DECAL PTO 826-127C
WS ZERK
Rev. 2
Rev 1; Use up stock
Rev. 2
Rev 1; Use up stock
(S/N 259230+)
(S/N 259230+)
WS SUPPORT BEARING
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Drivelines
Land Pride
Driveline CV (826-125C) Walterscheid
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg12660
826-125C
Drawing Image Number
PTO CV 2380 X 41.73
1.
2.
3.
4.
5.
6.
7.
8.
9.
382710
384517
020672
366862
382701
020616
319624
388954
041577
WS YOKE 1 3/8-6 SPL AS
WS DOUBLE YOKE
WS GREASE ZERK
WS INBOARD YOKE
WS CROSS & BEARING KIT
WS SPRING PIN
WS INNER PROFILE
WS PROFILE & SLEEVE W.A.
WS INBORD YOKE
10. 196839
10. 380906
11. 044444
12. 087276
13. 389961
14. 388957
15. 386163
16. 172762
17. 377335
18. 365305
19. 044321
20. 818-552C
21. 818-540C
22. 355155
23. 380371
24. 390404
24. 381908
25. 818-448C
WS YOKE 1 3/8-6 SPL ASGE
RPBY 196839
Rev. 2
Rev 1; Use up stock
WS CROSS & BRG KIT
WS BEARING RING - SC25
WS OUTER SHIELD TUBE OVL.
WS INNER SHIELD TUBE ROUND
WS CV CONE & BEARING ASSY
WS SHIELD CONE 3 RIB
WS SHIELD CONE - 5 RIB
WS SCREW
DRIVELINE SHIELD SAFETY CHAIN
DECAL DANGER PTO DRIVELINE
DECAL DANGER GUARD MISS PTO
WS SUPPORT BEARING
WS ZERK
WS ASGE COLLAR KIT
(RPBY 390404
DECAL PTO 826-125C
Rev. 2
Rev 1; Use up stock
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Drivelines
Land Pride
Driveline Left & Right Hand Deck Deck (826-126C) Walterscheid
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg12661
826-126C
Image Reference: 12661
PTO 2200 X 19.09 W/CLUTCH
WS FRICTION CLUTCH
WALTSCHEID CROSS & BRG KIT
WS SPRING PIN
1.
2.
3.
4.
5.
6.
6.
7.
8.
9.
053313
044439
020614
041065
180909
392047
390001
041068
377234
377240
WS INBOARD YOKE
WS INNER PROFILE OVAL
WS OUTER PROFILE 1L
RPBY 392047
(S/N 259230+)
(S/N 259229-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
WS INBOARD YOKE
WS SHIELD CONE-4 RIB
WS SHIELD CONE-10RIB
WS OUTER SHIELD OVL.
RPBY 392048
WS INNER SHIELD RND.
RPBY 392049
WS BEARING RING
DRIVELINE SHIELD SAFETY CHAIN
WS SCREW
DECAL DANGER PTO DRIVELINE
DECAL DANGER GUARD MISS PTO
WS ASGE YOKE 1 3/8-6 SPL.
RPBY 196837
WS ASGE COLLAR KIT
RPBY 3904
DECAL PTO 826-126C
WS ZERK
WS SUPPORT BEARING
10. 392048
10. 386424
11. 392049
11. 385365
12. 087279
13. 044321
14. 365305
15. 818-552C
16. 818-540C
17. 196837
17. 380905
18. 390404
18. 381908
19. 818-449C
20. 380371
21. 355154
(S/N 259230+)
(S/N 259229-)
(S/N 259230+)
(S/N 259229-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
Rev. 2 not compat. w/Rev. 1
Rev. 1
Rev. 2
Rev 1; Use up stock
Rev. 2
Rev 1; Use up stock
(S/N 259230+)
(S/N 259230+)
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Drivelines
Land Pride
Friction Clutch (053313)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg10600
053313
Drawing Image Number
WS FRICTION CLUTCH
WS SNAP RING
WS FLANGED RING
WS LOCK COLLAR
WS COMPRESSION SPRNG
WS BACK UP RING
WS BALL
1.
2.
3.
4.
5.
6.
7.
8.
9.
304149
338531
045790
045793
047825
020692
381957
043487
381495
WS HEX NUT M8
WS BELLEVILLE SPRING
WS THRUST PLATE
WS FRICTION DISK
WS HUB 1 3/8-6 SPL
WS CLUTCH HOUSING
WS Q.D. FLG. KIT
10. 168556
11. 051551
12. 041180
13. 341953
Includes one each of items 1 through
5 and three of item 6.
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Decks
Land Pride
Belt Drive Center (S/N 239258+)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg17278
Drawing Image Number
1.
1.
1.
1.
2.
3.
4.
5.
6.
7.
8.
9.
890-326C
890-322C
890-324C
890-701C
803-115C
804-014C
803-022C
804-022C
816-142C
310-251S
802-229C
310-051D
MWR BLD 1/4X16 7/8SD ML CCW
MWR BLD 1/4X16 7/8SD HL CCW
MWR BLD 1/4X16 7/8SD LL CCW
MWR BLD MULCH 1/4X16 7/8SD CCW
NUT HEX 7/16-20 PLT
WASHER LOCK 7/16 PLT
NUT HEX 5/8-18 PLT
WASHER LOCK SPRING 5/8 PLT
V-BELT B93 95.75 E.L. KEVLAR
CCW TG SPNDL HUB ASSY 5" PULL
HHCS 7/16-20X1 1/2 GR8
Standard Medium Lift
Optional High Lift
Optional Low Lift
Optional Mulch Blades
Includes items 25 through 34
IDLER SPACER
10. 808-073C
11. 802-237C
12. 315-143S
FLAT IDLE PULLEY 6 1/4 O.D.
HHCS 5/8-18X4 GR5
CEN-RH. IDLER TAKE-UP SUB
Includes one each of items 5; 10 &
13,15, 23, & 24 and two of item 22.
13. 802-051C
14. 803-014C
15. 310-165H
16. 802-567C
17. 310-095H
18. 800-099C
19. 310-094H
20. 807-068C
21. 802-228C
22. 803-024C
23. 310-353D
24. 310-354D
25. 800-001C
26. 803-228C
27. 172-242D
28. 804-093C
29. 808-075C
30. 822-161C
31. 310-457D
32. 310-631D
32. 310-455D
33. 822-006C
34. 315-494D
35. 802-696C
35. 802-447C
36. 804-110C
HHCS 5/8-11X1 1/2 GR5
NUT HEX 3/8-16 PLT
IDLER MOUNT BAR
SP EYE 3/8-16X4
SPRING EYE-BOLT BRACKET
SNAP RING EXT 7/16
OVER-CENTER LATCH-90
SPRING EXT BELT HANDLE
HHCS 5/8-11X1 1/2 GR5 NYL
NUT LOCK 5/8-11 PLT
IDLER LINK BAR LONG
IDLER LINK BAR SHORT
GREASE ZERK STRAIGHT 1/4-28
NUT HEX 3/4-16LH NYLOC COLLAR
1/4 SQ. KEY X 7/8 LG
WASHER FLAT 3/4 HARD ASTMF436
B-GROOVE PULLEY 5 O.D.
BEARING 6206 W/ METAL SHIELD
BLADE HUB MACHINED TOP GREASE
BLADE SPINDLE SHAFT CCW TG
RPBY 310-350S
BEARING 206
BLADE HUB C.C.W.
HFS 1/2-20X2 LH GR8
HFS 1/2-20X1 1/4 LH GR5
WASHER BLADE 2ODX.56THKX.51ID
(S/N 329661+)
(S/N 329660-)
Rev. 2 not compat. w/Rev. 1
(S/N 329661+)
(S/N 329660-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Decks
Land Pride
Belt Drive Center and Right Hand (S/N 212180-)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg12829
Drawing Image Number
1.
1.
1.
1.
2.
3.
4.
5.
6.
7.
890-326C
890-322C
890-324C
890-701C
803-115C
804-014C
803-022C
804-022C
816-142C
315-169S
MWR BLD 1/4X16 7/8SD ML CCW
MWR BLD 1/4X16 7/8SD HL CCW
MWR BLD 1/4X16 7/8SD LL CCW
MWR BLD MULCH 1/4X16.87SD CCW
NUT HEX 7/16-20 PLT
WASHER LOCK 7/16 PLT
NUT HEX 5/8-18 PLT
WASHER LOCK SPRING 5/8 PLT
V-BELT B93 95.75 E.L. KEVLAR
CCW SPDLE HUB ASSY 5"PULL 3"TB
Standard Medium Lift
Optional High Lift
Optional Low Lift
Optional Mulch Blades
Includes items 26 through 35, 37, 38
& 39
8.
9.
802-229C
310-051D
HHCS 7/16-20X1 1/2 GR8
IDLER SPACER
10. 808-073C
11. 802-237C
12. 315-143S
FLAT IDLE PULLEY 6 1/4 O.D.
HHCS 5/8-18X4 GR5
CEN-RH. IDLER TAKE-UP SUB
Includes one each of items 5, 10,
13,15, 23 & 24; and two of item 22
13. 802-051C
14. 803-014C
14. 803-006C
15. 310-165H
16. 802-567C
16. 802-443C
17. 310-095H
18. 800-099C
19. 310-094H
20. 807-068C
21. 802-228C
22. 803-024C
23. 310-353D
24. 310-354D
25. 315-176S
26. 802-447C
26. 802-696C
27. 310-043D
28. 315-494D
29. 315-493D
30. 822-006C
31. 310-224D
32. 808-075C
33. 172-242D
34. 803-228C
35. 800-075C
36. 310-176D
37. 804-093C
37. 804-025C
38. 822-161C
38. 822-006C
39. 310-312D
HHCS 5/8-11X1 1/2 GR5
NUT HEX 3/8-16 PLT
NUT HEX 1/4-20 PLT
IDLER MOUNT BAR
SP EYE 3/8-16X4
SP EYE 1/4-20X4 1/4-4 1/2
SPRING EYE-BOLT BRACKET
SNAP RING EXT 7/16
OVER-CENTER LATCH-90
SPRING EXT BELT HANDLE
HHCS 5/8-11X1 1/2 GR5 NYL
NUT LOCK 5/8-11 PLT
IDLER LINK BAR LONG
IDLER LINK BAR SHORT
CCW SPDLE HUB ASSY 5PULL 9.8TB
HFS 1/2-20X1 1/4 LH GR5
HFS 1/2-20X2 LH GR8
(S/N 174815+)
(S/N 174814-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
(S/N 174815+)
(S/N 174814-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
Includes items 26 through 38
Used with counter bored shaft
RPBY 804-110C
BLADE HUB C.C.W.
RPBY 310-352S
BEARING 206
BLADE HUB- MACH.-90
B-GROOVE PULLEY 5 O.D.
1/4 SQ. KEY X 7/8 LG
NUT HEX 3/4-16LH NYLOC COLLAR
ZERK 5/16-24 STRAIGHT #1711B
72 CENTER GREASE TUBE
WASHER FLAT 3/4 HARD ASTMF436
WASHER FLAT 3/4 SAE PLT
BEARING 6206 W/ METAL SHIELD
BEARING 206
Rev. 2
Rev 1; Use up stock
Rev. 2
Rev 1; Use up stock
LUBE FITTING 3" EXTENSION
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Decks
Land Pride
Belt Drive Center and Right Hand (S/N 212181 to 239257)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg16511
Drawing Image Number
1.
1.
1.
1.
2.
3.
4.
5.
6.
7.
8.
9.
890-326C
890-322C
890-324C
890-701C
803-115C
804-014C
803-022C
804-022C
816-142C
315-377S
802-229C
310-051D
MWR BLD 1/4X16 7/8SD ML CCW
MWR BLD 1/4X16 7/8SD HL CCW
MWR BLD 1/4X16 7/8SD LL CCW
MWR BLD MULCH 1/4X16.87SD CCW
NUT HEX 7/16-20 PLT
WASHER LOCK 7/16 PLT
NUT HEX 5/8-18 PLT
WASHER LOCK SPRING 5/8 PLT
V-BELT B93 95.75 E.L. KEVLAR
CCW SPINDLE HUB ASSEMBLY 5"
HHCS 7/16-20X1 1/2 GR8
Standard Medium Lift
Optional High Lift
Optional Low Lift
Optional Mulch Blades
Includes items 27 through 36
IDLER SPACER
10. 808-073C
11. 802-237C
12. 315-143S
FLAT IDLE PULLEY 6 1/4 O.D.
HHCS 5/8-18X4 GR5
CEN-RH. IDLER TAKE-UP SUB
Includes one each of items 5, 10,
13,15, 23 & 24; and two of item 22
13. 802-051C
14. 803-014C
15. 310-165H
16. 802-567C
17. 310-095H
18. 800-099C
19. 310-094H
20. 807-068C
21. 802-228C
22. 803-024C
23. 310-353D
24. 310-354D
25. 800-193C
26. 990-109R
27. 800-157C
28. 803-228C
29. 172-242D
30. 804-093C
31. 808-075C
32. 822-161C
33. 310-224D
34. 315-493D
35. 822-006C
36. 315-494D
37. 804-110C
38. 802-447C
38. 802-696C
HHCS 5/8-11X1 1/2 GR5
NUT HEX 3/8-16 PLT
IDLER MOUNT BAR
SP EYE 3/8-16X4
SPRING EYE-BOLT BRACKET
SNAP RING EXT 7/16
OVER-CENTER LATCH-90
SPRING EXT BELT HANDLE
HHCS 5/8-11X1 1/2 GR5 NYL
NUT LOCK 5/8-11 PLT
IDLER LINK BAR LONG
IDLER LINK BAR SHORT
GREASE ZERK 1/8NPT 45-DEG
TUBE NYLON 1/4OD X 062WL
FTG TUBE,CONNECTOR 1/8 MNPT
NUT HEX 3/4-16LH NYLOC COLLAR
1/4 SQ. KEY X 7/8 LG
Order Per Foot as Required
WASHER FLAT 3/4 HARD ASTMF436
B-GROOVE PULLEY 5 O.D.
BEARING 6206 W/ METAL SHIELD
BLADE HUB - MACH
RPBY 310-352S
BEARING 206
BLADE HUB C.C.W.
WASHER BLADE 2ODX.56THKX.51ID
HFS 1/2-20X1 1/4 LH GR5
HFS 1/2-20X2 LH GR8
Used with counter bored shaft
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Decks
Land Pride
Belt Drive Left Hand Deck (S/N 212180-)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg12830
Drawing Image Number
1.
1.
1.
1.
2.
3.
4.
5.
6.
7.
890-325C
890-219C
890-323C
890-700C
803-115C
804-014C
803-022C
804-022C
816-142C
310-132S
MWR BLD 1/4X16 7/8SD ML CW
MWR BLD 1/4X16 7/8SD HL CW
MWR BLD 1/4X16 7/8SD LL CW
MWR BLD MULCH 1/4X16.87SD CW
NUT HEX 7/16-20 PLT
WASHER LOCK 7/16 PLT
NUT HEX 5/8-18 PLT
WASHER LOCK SPRING 5/8 PLT
V-BELT B93 95.75 E.L. KEVLAR
CW SPDLE HUB ASSY 5"PULL 3"TB
Standard Medium Lift
Optional High Lift
Optional Low Lift
Optional Mulch Blades
Includes items 26 through 35, 37, 38
& 39
8.
9.
802-229C
310-051D
HHCS 7/16-20X1 1/2 GR8
IDLER SPACER
10. 808-073C
11. 802-237C
12. 310-166S
FLAT IDLE PULLEY 6 1/4 O.D.
HHCS 5/8-18X4 GR5
IDLER TAKE-UP SUB
Includes one each of items 5, 10,
13,15, 23 & 24 and two of item 22
13. 802-051C
14. 803-014C
14. 803-006C
15. 310-165H
16. 802-567C
16. 802-443C
17. 310-095H
18. 800-099C
19. 310-094H
20. 807-068C
21. 802-228C
22. 803-024C
23. 310-353D
24. 310-354D
25. 310-139S
26. 802-384C
26. 802-695C
27. 804-110C
27. 310-043D
28. 310-300D
29. 310-348S
29. 310-361D
30. 822-006C
31. 310-224D
32. 808-075C
33. 172-242D
34. 803-114C
35. 800-075C
36. 310-176D
37. 804-093C
37. 804-025C
38. 822-161C
38. 822-006C
39. 310-312D
40. 804-110C
HHCS 5/8-11X1 1/2 GR5
NUT HEX 3/8-16 PLT
NUT HEX 1/4-20 PLT
IDLER MOUNT BAR
SP EYE 3/8-16X4
SP EYE 1/4-20X4 1/4-4 1/2
SPRING EYE-BOLT BRACKET
SNAP RING EXT 7/16
OVER-CENTER LATCH-90
SPRING EXT BELT HANDLE
HHCS 5/8-11X1 1/2 GR5 NYL
NUT LOCK 5/8-11 PLT
IDLER LINK BAR LONG
IDLER LINK BAR SHORT
CW SPDLE HUB ASSY 5"PULL 9.8TB
HFS 1/2-20X1 1/4 GR5
(S/N 174815+)
(S/N 174814-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
(S/N 174815+)
(S/N 174814-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
Includes items 26 through 38
HFS 1/2-20X2 GR8
WASHER BLADE 2ODX.56THKX.51ID
RPBY 804-110C
BLADE HUB
SPDL 310-637D CW W/BOLT
RPBY 310-348S
Used with countered bpred shaft
Rev 1; Use up stock
BEARING 206
BLADE HUB- MACH.-90
B-GROOVE PULLEY 5 O.D.
1/4 SQ. KEY X 7/8 LG
NUT LOCK 3/4-16 NYLOC COLLAR
ZERK 5/16-24 STRAIGHT #1711B
72 CENTER GREASE TUBE
WASHER FLAT 3/4 HARD ASTMF436
WASHER FLAT 3/4 SAE PLT
BEARING 6206 W/ METAL SHIELD
BEARING 206
Rev. 2
Rev 1; Use up stock
Rev. 2
Rev 1; Use up stock
LUBE FITTING 3" EXTENSION
WASHER BLADE 2ODX.56THKX.51ID
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Decks
Land Pride
Belt Drive Left Hand Deck (S/N 212181 to 239257)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg16522
Drawing Image Number
1.
1.
1.
1.
2.
3.
4.
5.
6.
7.
8.
9.
890-325C
890-219C
890-323C
890-700C
803-115C
804-014C
803-022C
804-022C
816-142C
315-375S
802-229C
310-051D
MWR BLD 1/4X16 7/8SD ML CW
MWR BLD 1/4X16 7/8SD HL CW
MWR BLD 1/4X16 7/8SD LL CW
MWR BLD MULCH 1/4X16.87SD CW
NUT HEX 7/16-20 PLT
Standard Medium Lift
Optional High Lift
Optional Low Lift
Optional Mulch Blades
WASHER LOCK 7/16 PLT
NUT HEX 5/8-18 PLT
WASHER LOCK SPRING 5/8 PLT
V-BELT B93 95.75 E.L. KEVLAR
CW SPINDLE HUB ASSEMBLY 5IN.
HHCS 7/16-20X1 1/2 GR8
IDLER SPACER
Includes items 27 through 36
10. 808-073C
11. 802-237C
12. 310-166S
FLAT IDLE PULLEY 6 1/4 O.D.
HHCS 5/8-18X4 GR5
IDLER TAKE-UP SUB
Includes one each of items 5, 10,
13,15, 23 & 24 and two of item 22.
13. 802-051C
14. 803-014C
15. 310-165H
16. 802-567C
17. 310-095H
18. 800-099C
19. 310-094H
20. 807-068C
21. 802-228C
22. 803-024C
23. 310-353D
24. 310-354D
25. 800-193C
26. 990-109R
27. 800-157C
28. 803-114C
29. 172-242D
30. 804-093C
31. 808-075C
32. 822-161C
33. 310-224D
34. 310-348S
34. 310-361D
35. 822-006C
36. 310-300D
37. 802-695C
37. 802-384C
38. 804-110C
HHCS 5/8-11X1 1/2 GR5
NUT HEX 3/8-16 PLT
IDLER MOUNT BAR
SP EYE 3/8-16X4
SPRING EYE-BOLT BRACKET
SNAP RING EXT 7/16
OVER-CENTER LATCH-90
SPRING EXT BELT HANDLE
HHCS 5/8-11X1 1/2 GR5 NYL
NUT LOCK 5/8-11 PLT
IDLER LINK BAR LONG
IDLER LINK BAR SHORT
GREASE ZERK 1/8NPT 45-DEG
TUBE NYLON 1/4OD X 062WL
FTG TUBE,CONNECTOR 1/8 MNPT
NUT LOCK 3/4-16 NYLOC COLLAR
1/4 SQ. KEY X 7/8 LG
WASHER FLAT 3/4 HARD ASTMF436
B-GROOVE PULLEY 5 O.D.
BEARING 6206 W/ METAL SHIELD
BLADE HUB - MACH
SPDL 310-637D CW W/BOLT
RPBY 310-348S
Order Per Foot as Required
BEARING 206
BLADE HUB - 7/8
HFS 1/2-20X2 GR8
HFS 1/2-20X1 1/4 GR5
Used with countered bored shaft
WASHER BLADE 2ODX.56THKX.51ID
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Decks
Land Pride
Belt Drive Left Hand Deck (S/N 239258+)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg17280
Drawing Image Number
1.
1.
1.
1.
2.
3.
4.
5.
6.
7.
8.
9.
890-219C
890-325C
890-323C
890-700C
803-115C
804-014C
803-022C
804-022C
816-142C
315-375S
802-229C
310-051D
MWR BLD 1/4X16 7/8SD HL CW
MWR BLD 1/4X16 7/8SD ML CW
MWR BLD 1/4X16 7/8SD LL CW
MWR BLD MULCH 1/4X16.87SD CW
NUT HEX 7/16-20 PLT
Optional High Lift
Standard Medium Lift
Optional Low Lift
Optional Mulch Blades
WASHER LOCK 7/16 PLT
NUT HEX 5/8-18 PLT
WASHER LOCK SPRING 5/8 PLT
V-BELT B93 95.75 E.L. KEVLAR
CW SPINDLE HUB ASSEMBLY 5IN.
HHCS 7/16-20X1 1/2 GR8
IDLER SPACER
Includes items 27 through 36
10. 808-073C
11. 802-237C
12. 310-166S
FLAT IDLE PULLEY 6 1/4 O.D.
HHCS 5/8-18X4 GR5
IDLER TAKE-UP SUB
Includes one each of items 5, 10,
13,15, 23 & 24 and two of item 22
13. 802-051C
14. 803-014C
15. 310-165H
16. 802-567C
17. 310-095H
18. 800-099C
19. 310-094H
20. 807-068C
21. 802-228C
22. 803-024C
23. 310-353D
24. 310-354D
25. 800-193C
26. 990-109R
27. 800-157C
28. 803-114C
29. 172-242D
30. 804-093C
31. 808-075C
32. 822-161C
33. 310-224D
34. 310-348S
34. 310-361D
35. 822-006C
36. 310-300D
37. 800-001C
38. 310-457D
39. 310-630D
39. 310-454D
40. 310-248S
HHCS 5/8-11X1 1/2 GR5
NUT HEX 3/8-16 PLT
IDLER MOUNT BAR
SP EYE 3/8-16X4
SPRING EYE-BOLT BRACKET
SNAP RING EXT 7/16
OVER-CENTER LATCH-90
SPRING EXT BELT HANDLE
HHCS 5/8-11X1 1/2 GR5 NYL
NUT LOCK 5/8-11 PLT
IDLER LINK BAR LONG
IDLER LINK BAR SHORT
GREASE ZERK 1/8NPT 45-DEG
TUBE NYLON 1/4OD X 062WL
FTG TUBE,CONNECTOR 1/8 MNPT
NUT LOCK 3/4-16 NYLOC COLLAR
1/4 SQ. KEY X 7/8 LG
WASHER FLAT 3/4 HARD ASTMF436
B-GROOVE PULLEY 5 O.D.
BEARING 6206 W/ METAL SHIELD
BLADE HUB - MACH
Order Per Foot as Required
SPDL 310-637D CW W/BOLT
RPBY 310-348S
BEARING 206
BLADE HUB - 7/8
GREASE ZERK STRAIGHT 1/4-28
BLADE HUB MACHINED TOP GREASE
BLADE SPINDLE SHAFT CW TG
RPBY 310-349S
(S/N 329661+)
(S/N 329660-)
Includes items 28 through 32 and 35
through 39
Rev. 2 not compat. w/Rev. 1
Rev. 1
CW TG SPINDLE HUB ASSY 5" PULL
41. 802-695C
41. 802-384C
42. 804-110C
HFS 1/2-20X2 GR8
HFS 1/2-20X1 1/4 GR5
WASHER BLADE 2ODX.56THKX.51ID
(S/N 329661+)
(S/N 329660-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Decks
Land Pride
Belt Drive Right Hand (S/N 239258+)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg17279
Drawing Image Number
1.
1.
1.
2.
3.
4.
5.
6.
7.
8.
9.
890-326C
890-322C
890-324C
803-115C
804-014C
803-022C
804-022C
816-142C
310-251S
802-229C
310-051D
MWR BLD 1/4X16 7/8SD ML CCW
MWR BLD 1/4X16 7/8SD HL CCW
MWR BLD 1/4X16 7/8SD LL CCW
NUT HEX 7/16-20 PLT
WASHER LOCK 7/16 PLT
NUT HEX 5/8-18 PLT
WASHER LOCK SPRING 5/8 PLT
V-BELT B93 95.75 E.L. KEVLAR
CCW TG SPNDL HUB ASSY 5" PULL
HHCS 7/16-20X1 1/2 GR8
IDLER SPACER
Standard Medium Lift
Optional High Lift
Optional Low Lift
Includes items 28 through 37
10. 808-073C
11. 802-237C
12. 315-143S
FLAT IDLE PULLEY 6 1/4 O.D.
HHCS 5/8-18X4 GR5
CEN-RH. IDLER TAKE-UP SUB
Includes one each of items 5, 10, 13,
15,23 & 24 and two of item 22
13. 802-051C
14. 803-014C
15. 310-165H
16. 802-567C
17. 310-095H
18. 800-099C
19. 310-094H
20. 807-068C
21. 802-228C
22. 803-024C
23. 310-353D
24. 310-354D
25. 800-193C
26. 990-109R
27. 800-157C
28. 803-228C
29. 172-242D
30. 804-093C
31. 808-075C
32. 822-161C
33. 310-457D
34. 310-631D
34. 310-455D
35. 822-006C
36. 315-494D
37. 800-001C
38. 310-224D
39. 310-352S
39. 315-493D
40. 315-377S
HHCS 5/8-11X1 1/2 GR5
NUT HEX 3/8-16 PLT
IDLER MOUNT BAR
SP EYE 3/8-16X4
SPRING EYE-BOLT BRACKET
SNAP RING EXT 7/16
OVER-CENTER LATCH-90
SPRING EXT BELT HANDLE
HHCS 5/8-11X1 1/2 GR5 NYL
NUT LOCK 5/8-11 PLT
IDLER LINK BAR LONG
IDLER LINK BAR SHORT
GREASE ZERK 1/8NPT 45-DEG
TUBE NYLON 1/4OD X 062WL
FTG TUBE,CONNECTOR 1/8 MNPT
NUT HEX 3/4-16LH NYLOC COLLAR
1/4 SQ. KEY X 7/8 LG
WASHER FLAT 3/4 HARD ASTMF436
B-GROOVE PULLEY 5 O.D.
BEARING 6206 W/ METAL SHIELD
BLADE HUB MACHINED TOP GREASE
BLADE SPINDLE SHAFT CCW TG
RPBY 310-350S
BEARING 206
BLADE HUB C.C.W.
GREASE ZERK STRAIGHT 1/4-28
BLADE HUB - MACH
SPDL 310-636D CCW W/BOLT
RPBY 310-352S
Order Per Foot as Required
(S/N 329661+)
(S/N 329660-)
Rev. 2 not compat. w/Rev. 1
CCW SPINDLE HUB ASSEMBLY 5"
Includes items 27 through 32, 35, 36,
38 & 39
41. 802-696C
41. 802-447C
42. 804-110C
HFS 1/2-20X2 LH GR8
HFS 1/2-20X1 1/4 LH GR5
WASHER BLADE 2ODX.56THKX.51ID
(S/N 329661+)
(S/N 329660-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Decks
Land Pride
Channel Center Deck
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg16523
Drawing Image Number
1.
2.
3.
4.
4.
5.
6.
6.
6.
6.
7.
8.
805-017C
11-007
PIN COTTER 3/16 X 1 3/4 PLT
ITG 1"-14 SLOTTED HEX NUT
WASHER FLAT 1 SAE PLT
B-GROOVE PULLEY 12" CAST-IRON
B-GROOVE DRIVE PULLEY 12 OD
KEY 1/4" X 11/16" LONG
GBOX MOWER 50 HP 1:2.8 CCW
RPBY 826-327C
RPBY 826-295C
804-029C
808-336C
808-182C
310-331D
826-327C
826-295C
826-205C
826-123C
817-050C
315-411H
Rev. 2
Rev 1; Use up stock
Service Only
Rev. 4
Rev. 3
(S/N 214222-340848)
(S/N 214222 )
(S/N 214221-)
(S/N 218010-)
(S/N 239258+)
Rev. 2 not compat. w/Rev. 1
Rev. 1
RPBY 826-205C
GEARBOX SHAFT PROTECTOR
AFM4011 CENTER GB CHANNEL WELD
Rev. 3 not compat. w/Rev. 2 or
1
8.
315-391H
11AFM CENTER GEARBOX MNT WLDMT
(S/N 225160-239257)
Rev. 3 not compat. w/Rev. 2 or
1
8.
8.
9.
9.
315-276H
315-151H
803-037C
803-020C
133 CEN. GEAR BOX CHANNEL
G.B. MOUNT CHANNEL-CEN AFM133
NUT HEX WHIZ 1/2-13 PLT
NUT HEX 1/2-13 PLT
WASHER LOCK SPRING 1/2 PLT
HFSS 1/2-13X1 1/2 GR5
HHCS 1/2-13X1 1/4 GR5
HHCS 5/8-18X1 3/4 GR5
WASHER LOCK SPRING 5/8 PLT
NUT HEX 5/8-18 PLT
WASHER FLAT 1/2 SAE PLT
HFSS 1/2-13X1 1/2 GR5
HHCS 1/2-13X1 1/2 GR5
SMV MOUNT BAR SPRING STEEL
SMV MOUNT BAR
DECAL SLOW MOVING-GALV. BACKED
NUT HEX FLANGE LOCK 1/4-20 PLT
NUT SQ 1/4-20 PLT
WASHER LOCK SPRING 1/4 PLT
SCREW RD HD 1/4-20 X 5/8
SMV PACKAGE
(S/N 176350-225159)
(S/N 176349-)
(S/N 286810+)
(S/N 286809-)
(S/N 286809-)
(S/N 286810+)
(S/N 286809-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
Rev. 2 not compat. w/Rev. 1
Rev. 1
10. 804-015C
11. 802-203C
11. 802-034C
12. 802-246C
13. 804-022C
14. 803-022C
15. 804-016C
16. 802-203C
16. 802-091C
17. 807-176C
17. 315-478D
18. 818-055C
19. 803-293C
19. 803-005C
20. 804-006C
21. 801-018C
22. 315-037V
23. 802-005C
24. 816-298C
25. 310-041D
Rev. 2 not compat. w/Rev. 1
Rev. 1
(S/N 286809-)
(S/N 286810+)
(S/N 286809-)
(S/N 239258+)
(S/N 239257-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
Rev. 2
Rev 1; Use up stock
Rev. 2
Rev 1; Use up stock
Not required with lock nut
Includes items 18 through 22
HHCS 1/4-20X1 GR5
RUBBER PLUG 1 3/8 W/CROSS SLIT
GEAR BOX SPACER
(S/N 211744-)
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Decks
Land Pride
Channel Left Hand Deck
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg16524
Drawing Image Number
1.
2.
3.
4.
4.
5.
6.
6.
6.
6.
805-017C
11-007
PIN COTTER 3/16 X 1 3/4 PLT
ITG 1"-14 SLOTTED HEX NUT
WASHER FLAT 1 SAE PLT
B-GROOVE PULLEY 12" CAST-IRON
B-GROOVE DRIVE PULLEY 12 OD
KEY 1/4" X 11/16" LONG
GBOX MOWER 50 HP 1:2.8 CW
RPBY 826-326C
804-029C
808-336C
808-182C
310-331D
826-326C
826-296C
826-206C
826-085C
Rev. 2
Rev. 1
Service Only
(S/N 214222-340848)
(S/N 214222+)
(S/N 214221-) If the new gear box
826-206C is ordered then part
number 315-141H item 15 must also
be ordered.
Rev. 3
Rev. 2
Rev. 1
RPBY 826-296C
RPBY 826-206C
7.
8.
817-050C
315-158S
GEARBOX SHAFT PROTECTOR
AFM4011 LH GB CHANNEL ASSY CW
(S/N 218010-)
Includes items 1 through 7, 9, 10, 11
& 21
9.
9.
9.
315-392H
315-275H
315-150H
11AFM WING GEARBOX MNT WLDMT
133 WING GEAR BOX CHANNEL
(S/N 225160+)
Rev. 2 not compat. w/Rev. 1;
Rev. 3
Rev. 2 not compat. w/Rev. 1;
Rev. 2
(S/N 176350-225159)
(S/N 176349-)
G.B. MOUNT CHANNEL-WING AFM133
NUT HEX 5/8-18 PLT
WASHER LOCK SPRING 5/8 PLT
NUT HEX WHIZ 1/2-13 PLT
NUT HEX 1/2-13 PLT
WASHER LOCK SPRING 1/2 PLT
HFSS 1/2-13X1 1/2 GR5
HHCS 1/2-13X1 1/4 GR5
Rev. 1
10. 803-022C
11. 804-022C
12. 803-037C
12. 803-020C
13. 804-015C
14. 802-203C
14. 802-034C
15. 315-141H
(S/N 286810+)
(S/N 286809-)
(S/N 286809-)
(S/N 286810+)
Rev. 2 not compat. w/Rev. 1
Rev. 1
Rev. 2 not compat. w/Rev. 1
Rev. 1
(S/N 286809-)
WING DECK FLEX ARM
(S/N 214222+) This weldment was
revised to fit the new gear box
826-206C.
16. 890-331C
17. 804-022C
18. 803-021C
19. 802-203C
19. 802-091C
20. 802-055C
21. 804-016C
22. 802-246C
23. 315-488D
24. 802-370C
25. 803-007C
26. 310-041D
27. 800-080C
BUSHING 1 X 3/4 X 1
WASHER LOCK SPRING 5/8 PLT
NUT HEX 5/8-11 PLT
HFSS 1/2-13X1 1/2 GR5
HHCS 1/2-13X1 1/2 GR5
HHCS 5/8-11X2 GR5
WASHER FLAT 1/2 SAE PLT
HHCS 5/8-18X1 3/4 GR5
DECK TO TOOLBAR PIN
HHCS 1/4-20X1 3/4 GR5
NUT LOCK 1/4-20 PLT
(S/N 286810+)
(S/N 286809-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
(S/N 286809-)
GEAR BOX SPACER
GREASE ZERK 1/4-28 THD FORMING
(S/N 211744-)
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Decks
Land Pride
Channel Right Hand Deck
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg16525
Drawing Image Number
1.
2.
3.
4.
805-017C
11-007
804-029C
808-336C
PIN COTTER 3/16 X 1 3/4 PLT
ITG 1"-14 SLOTTED HEX NUT
WASHER FLAT 1 SAE PLT
B-GROOVE PULLEY 12" CAST-IRON 2nd
revision
4.
5.
6.
6.
6.
6.
808-182C
310-331D
826-327C
826-295C
826-205C
826-123C
B-GROOVE DRIVE PULLEY 12 OD 1st revision
KEY 1/4" X 11/16" LONG
GBOX MOWER 50 HP 1:2.8 CCW
RPBY 826-327C
RPBY 826-295C
RPBY 826-205C
Service Only
(S/N 214222 <-> 340848)
(S/N 214222+)
(S/N 214221-) If the new gear box
826-205C is ordered then part
number 315-141H item 15 must also
be ordered.
Rev. 3
Rev. 2
Rev. 1
7.
8.
9.
817-050C
802-246C
315-392H
GEARBOX SHAFT PROTECTOR
HHCS 5/8-18X1 3/4 GR5
11AFM WING GEARBOX MNT WLDMT
(S/N 218010-)
(S/N 225160+)
Rev. 2 not compat. w/Rev. 1;
Rev. 3
9.
9.
315-275H
315-150H
133 WING GEAR BOX CHANNEL
G.B. MOUNT CHANNEL-WING AFM133
NUT HEX 5/8-18 PLT
WASHER LOCK SPRING 5/8 PLT
NUT HEX WHIZ 1/2-13 PLT
NUT HEX 1/2-13 PLT
WASHER LOCK SPRING 1/2 PLT
HFSS 1/2-13X1 1/2 GR5
HHCS 1/2-13X1 1/4 GR5
(S/N 176350 <-> 225159)
(S/N 176349-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
10. 803-022C
11. 804-022C
12. 803-037C
12. 803-020C
13. 804-015C
14. 802-203C
14. 802-034C
15. 315-141H
(S/N 286810+)
(S/N 286809-)
(S/N 286809-)
(S/N 286810+)
Rev. 2 not compat. w/Rev. 1
Rev. 1
Rev. 2 not compat. w/Rev. 1
Rev. 1
(S/N 286809-)
WING DECK FLEX ARM
(S/N 214222+) This weldment was
revised to fit the new gear box
826-205C.
16. 890-331C
17. 804-022C
18. 803-021C
19. 802-203C
19. 802-091C
20. 802-055C
21. 804-016C
22. 315-488D
23. 802-370C
24. 803-007C
25. 310-041D
26. 800-080C
BUSHING 1 X 3/4 X 1
WASHER LOCK SPRING 5/8 PLT
NUT HEX 5/8-11 PLT
HFSS 1/2-13X1 1/2 GR5
HHCS 1/2-13X1 1/2 GR5
HHCS 5/8-11X2 GR5
WASHER FLAT 1/2 SAE PLT
DECK TO TOOLBAR PIN
HHCS 1/4-20X1 3/4 GR5
NUT LOCK 1/4-20 PLT
(S/N 286810+)
(S/N 286809-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
(S/N 286809-)
GEAR BOX SPACER
GREASE ZERK 1/4-28 THD FORMING
(S/N 211744-)
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Decks
Land Pride
Deck and Roller
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg12652
Drawing Image Number
1.
1.
2.
3.
4.
5.
6.
6.
7.
8.
8.
9.
315-133H
310-319H
817-082C
804-013C
803-014C
803-114C
315-409D
310-533D
802-017C
800-163C
800-115C
800-116C
FRONT ROLLER BRKT L.H.
LOW LH FRONT ROLLER WELDMENT
4 X 5 1/2 FRONT ROLLER
WASHER LOCK SPRING 3/8 PLT
NUT HEX 3/8-16 PLT
NUT LOCK 3/4-16 NYLOC COLLAR
FRONT ROLLER MOUNT-R.H.
LOW FRONT ROLLER RH BRACKET
HHCS 3/8-16X1 GR5
CLIP U-TYPE NUT 1/4-20 SLF-RET
CLIP, U-TYPE NUT
NYLON PUSH-ON RETAINER
REP BY 817-192C & 800-163C
KNOB 3 PRONG 1/4-20 X 1/2 LG
NUT LOCK 1/2-13 PLT
(S/N 176001+)
(S/N 176000-)
Rev. 2
Rev 1; Use up stock
(S/N 176001+)
(S/N 176000-)
Rev. 2
Rev 1; Use up stock
(S/N 143133<->176349)
(S/N 143132-)
(S/N 143132-)
(S/N 143132-)
(S/N143133<->176349)
Rev. 2 not compat. w/Rev. 1
Rev. 1
10. 800-114C
11. 817-192C
12. 803-019C
13. 817-195C
13. 315-234D
ROLLER ANTI-SCALP 2 OD 2nd revision
RPBY 817-195C Use up existing stock; revision
1
14. 802-041C
15. 315-789D
HHCS 1/2-13X3 1/2 GR5
AFM4011 BELT COVER
(S/N 239258+)
Rev. 2 not compat. w/Rev. 1 or
3; Rev. 4
15. 315-776D
AFM4011 BELT GUARD
(S/N 225160 <-> 229257)
Rev. 2 not compat. w/Rev. 1;
Rev. 3
15. 315-618D
16. 315-481D
17. 817-259C
18. 803-231C
19. 315-281H
19. 315-120H
19. 315-282H
19. 315-121H
40133 BELT GUARD
(S/N 176350 <-> 225159)
(S/N 176349-)
(S/N 176350+)
(S/N 176350+)
(S/N 17650+)
(S/N 176349-)
(S/N 176350+
(S/N 176349-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
48" DECK BELT GUARD
KNOB 3/8-16 FEMALE THD 2 3/8OD
NUT WING 3/8-16 PLT
133 L.H. DECK WELD
RPBY 315-506A
Rev. 2 not compat. w/Rev. 1
Rev. 1
Rev. 2 not compat. w/Rev. 1
Rev. 1
133 CEN.-R.H. DECK WELD
RPBY 315-209A OR 315-217A
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Gauge Wheels
Land Pride
Gauge Wheel Castered (176349-)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg12700
Drawing Image Number
1.
2.
3.
4.
5.
6.
7.
8.
9.
315-156S
310-024D
814-071C
310-328D
804-015C
803-018C
818-238C
310-149H
802-350C
RPBY 310-105S
GAUGE WHEEL SPACER - SHORT
TIRE 10 X 4 TUBELESS AIR
SPACER TUBE GA. WHL. 5 1/8 LG
WASHER LOCK SPRING 1/2 PLT
NUT HEX 1/2-20 PLT
DECAL TIRES INJECTED W/SEALANT
GAUGE WHEEL YOKE(5 1/8 INSIDE)
HHCS 1/2-20X6 1/2 GR5
SPACER 1"
10. 827-002C
11. 827-001C
12. 805-126C
SPACER 1/2"
PIN LYNCH 1/4 X 1 3/4 PLT
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Gauge Wheels
Land Pride
Gauge Wheel Castered (S/N 176350 to 225159-)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg10500
Drawing Image Number
11X4.00 CASTER GW YOKE
11X400-5 (LITE FOAM) RIB TIRE
11 X 400-5 RIB TIRE W 3/4 BRGS
NUT HEX 3/4-10 PLT NYLOCK
11' GW YOKE 5 1/8X5 1/8 INSIDE
HHCS 3/4-10X7 GR5
SPACER 1"
SPACER 1/2"
PIN LYNCH 1/4 X 1 3/4 PLT
1.
1.
2.
3.
4.
5.
6.
7.
8.
315-291S
814-191C
814-144C
803-025C
315-300H
802-095C
827-002C
827-001C
805-126C
Optional foam filled tire
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Gauge Wheels
Land Pride
Gauge Wheel Center Deck (S/N 225159-)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg12648
Drawing Image Number
1.
1.
2.
3.
4.
5.
6.
7.
8.
9.
315-282H
315-121H
803-014C
804-013C
315-130H
802-017C
827-001C
817-152C
817-151C
315-484D
133 CEN.-R.H. DECK WELD
R.H. & CEN. 48" DECK WELD
NUT HEX 3/8-16 PLT
WASHER LOCK SPRING 3/8 PLT
REAR DECK SUPPORT MT. AFM133
HHCS 3/8-16X1 GR5
(S/N 176350+)
(S/N 176349-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
SPACER 1/2"
GW SNAP ON SPACER - 1" THICK
GW SNAP ON SPACER - 1/4" THICK
CEN DECK CARRIER ROD
PIN ROLL 3/8 X 1 3/4 LG PLT
DECK SUPPORT MOUNT PLATE
10. 805-161C
11. 315-399D
(S/N 176349-) Replaced by
806-047C.
(S/N 176349-) Replaced by
806-047C.
Use up stock
Use up stock
12. 802-024C
HHCS 3/8-16X3 GR5
13. 802-079C
14. 315-333H
14. 315-131H
15. 315-334H
15. 315-132H
16. 805-126C
17. 315-291S
17. 315-156S
18. 800-001C
19. 817-048C
20. 806-047C
21. 804-012C
HHCS 3/8-16X1 1/4 GR5
AFM40133 CEN. DECK CARRIER-RH
RPBY 315-333H
AFM40133 CEN. DECK CARRIER-LH
RPBY 315-334H
PIN LYNCH 1/4 X 1 3/4 PLT
11X4.00 CASTER GW YOKE
CASTERED G.W.YOKE ASSY
GREASE ZERK STRAIGHT 1/4-28
SPINDLE BUSHING
Rev. 2
Rev 1; Use up stock
Rev. 2
Rev 1; Use up stock
(S/N 176350 <-> 225159)
(S/N 176349-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
U-BOLT 3/8-16 X 1 17/32 X2 3/4
WASHER FLAT 3/8 SAE PLT
(S/N 176350+)
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Gauge Wheels
Land Pride
Gauge Wheel Center Deck (S/N 225160+)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg16679
Drawing Image Number
1.
2.
2.
3.
4.
5.
6.
7.
8.
9.
315-282H
805-126C
805-065C
310-359D
310-252D
310-251D
890-202C
800-001C
315-401H
802-305C
133 CEN.-R.H. DECK WELD
PIN LYNCH 1/4 X 1 3/4 PLT
PIN WIRE RETAINING 1/4 X 1 3/4
GW SPACER 1/4
G.W. SPACER 1/2
G.W. SPACER 1
GAUGE WHEEL SFT PIVOT BUSHING
GREASE ZERK STRAIGHT 1/4-28
13X5 CENTER DECK LH CARRIER
HHCS 1/2-20X8 GR5
(S/N 264391+)
(S/N 264390-)
Rev. 2
Rev 1; Use up stock
10. 310-090H
11. 804-015C
12. 803-018C
13. 827-056C
14. 814-172C
15. 315-399S
90 GAUGE WHEEL YOKE
WASHER LOCK SPRING 1/2 PLT
NUT HEX 1/2-20 PLT
SPACER GW 3/4ODX33/64IDX6 3/8L
TIRE 13X5W/HLS&3/4IDTAPER BRGS
13X5 CASTER GW YOKE SUB
Includes items 2 through 5 and 9
through 14
16. 802-079C
17. 804-011C
18. 804-013C
19. 803-014C
20. 315-397H
21. 827-001C
22. 817-152C
23. 817-151C
24. 315-543D
24. 315-484D
25. 805-126C
25. 805-161C
26. 315-544D
HHCS 3/8-16X1 1/4 GR5
WASHER FLAT 3/8 USS PLT
WASHER LOCK SPRING 3/8 PLT
NUT HEX 3/8-16 PLT
13X5 CENTER DECK RH CARRIER
SPACER 1/2"
GW SNAP ON SPACER - 1" THICK
GW SNAP ON SPACER - 1/4" THICK
11' CEN DCK CARRIER ROD W/GRV
CEN DECK CARRIER ROD
PIN LYNCH 1/4 X 1 3/4 PLT
PIN ROLL 3/8 X 1 3/4 LG PLT
C SPACER COLLAR 1/2 THK X 1 ID
(S/N 241418-)
(S/N 241418-)
(S/N 241418-)
(S/N 241419+)
(S/N 241418-)
(S/N 241419+)
(S/N 241418-)
(S/N 241419+)
Rev. 2 not compat. w/Rev. 1
Rev. 1
Rev. 2 not compat. w/Rev. 1
Rev. 1
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Gauge Wheels
Land Pride
Gauge Wheel Left & Right Hand Deck (S/N 225159-)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg16526
Drawing Image Number
1.
1.
2.
2.
3.
4.
5.
5.
6.
7.
8.
9.
315-291S
315-156S
315-294S
315-157S
817-048C
800-001C
315-299H
315-126H
802-017C
805-126C
804-013C
803-014C
11X4.00 CASTER GW YOKE
CASTERED G.W.YOKE ASSY
11X4.00 CASTER GW ARM ASSEMBLY
CASTERED G.W. ARM ASSY
SPINDLE BUSHING
GREASE ZERK STRAIGHT 1/4-28
AFM40133 CASTERED GW ARM FRONT
WING DECK G.W. ARM FR. AFM133
HHCS 3/8-16X1 GR5
(S/N 176350+)
(S/N 176349-)
(S/N 176350+)
(S/N 176349-)
Rev. 2
Rev 1; Use up stock
Rev. 2 not compat. w/Rev. 1
Rev. 1
(S/N 176350+)
(S/N 176349-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
PIN LYNCH 1/4 X 1 3/4 PLT
WASHER LOCK SPRING 3/8 PLT
NUT HEX 3/8-16 PLT
10. 827-001C
11. 817-152C
12. 817-151C
13. 805-177C
14. 315-125H
15. 802-058C
16. 804-022C
17. 803-021C
18. 315-124H
19. 315-271H
19. 315-270H
20. 315-292S
20. 315-159S
21. 315-301H
21. 315-127H
22. 804-012C
23. 802-079C
SPACER 1/2"
(S/N 176349-)
(S/N 176349-)
(S/N 176349-)
(S/N 176349-)
(S/N 176349-)
(S/N 176349-)
(S/N 176349-)
(S/N 176349-)
(S/N 176349-)
(S/N 176350+)
(S/N 176350+)
(S/N 176350+)
(S/N 176349-)
(S/N 176350+)
(S/N 176349-)
GW SNAP ON SPACER - 1" THICK
GW SNAP ON SPACER - 1/4" THICK
PIN ROLL 5/16 X 1 3/4 PLT
WING DECK CORNER ROD AFM133
HHCS 5/8-11X2 1/2 GR5
WASHER LOCK SPRING 5/8 PLT
NUT HEX 5/8-11 PLT
WING DECK CORNER CARRIER AFM133
133 LH INSIDE NONCASTER ARM
133 RH INSIDE NONCASTER ARM
11X4.00 NONCASTER GW YOKE
NON-CASTERED G.W.YOKE ASSY
11' WING DECK OUTER GW ARM
WING DECK G.W. ARM RE. AFM133
WASHER FLAT 3/8 SAE PLT
HHCS 3/8-16X1 1/4 GR5
Rev. 2
Rev 1; Use up stock
Rev. 2 not compat. w/Rev. 1
Rev. 1
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Gauge Wheels
Land Pride
Gauge Wheel Left & Right Hand Deck (S/N 225160+)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg16680
Drawing Image Number
1.
2.
2.
3.
4.
5.
6.
7.
8.
9.
802-079C
315-396H
315-395H
804-011C
804-013C
803-014C
814-172C
827-056C
803-018C
804-015C
HHCS 3/8-16X1 1/4 GR5
13X5 INNER LH NON-CASTER ARM
13X5 INNER RH NON-CASTER ARM
WASHER FLAT 3/8 USS PLT
WASHER LOCK SPRING 3/8 PLT
NUT HEX 3/8-16 PLT
TIRE 13X5W/HLS&3/4IDTAPER BRGS
SPACER GW 3/4ODX33/64IDX6 3/8L
NUT HEX 1/2-20 PLT
WASHER LOCK SPRING 1/2 PLT
90 GAUGE WHEEL YOKE
10. 310-090H
11. 802-305C
12. 310-251D
13. 310-252D
14. 310-359D
15. 805-126C
15. 805-065C
16. 890-202C
17. 800-001C
18. 315-393H
19. 315-402S
20. 315-248D
21. 315-247D
22. 315-246D
23. 315-245D
24. 315-098H
25. 315-399S
26. 315-400S
HHCS 1/2-20X8 GR5
G.W. SPACER 1
G.W. SPACER 1/2
GW SPACER 1/4
PIN LYNCH 1/4 X 1 3/4 PLT
PIN WIRE RETAINING 1/4 X 1 3/4
GAUGE WHEEL SFT PIVOT BUSHING
GREASE ZERK STRAIGHT 1/4-28
13X5 CASTER GAUGE WHEEL ARM
13X5 CASTER GW ARM ASSEMBLY
1 1/4 SQ BAR TOP CAP
1 1/4 SQ BAR SPACER 1/4 LG
1 1/4 SQ BAR SPACER 1/2 LG
1 1/4 SQ BAR SPACER 1 LG
NON-CASTER GW YOKE WELD
13X5 CASTER GW YOKE SUB
13X5 NONCASTER GW YOKE SUB
(S/N 264391+)
(S/N 264390-)
Rev. 2
Rev 1; Use up stock
Includes items 16, 17 & 18
Includes items 6 through 15
Includes items 6 through 9, 11, 15 &
20 through 24
27. 315-394H
28. 315-494A
29. 315-500H
30. 315-499H
31. 315-498H
32. 803-169C
33. 802-226C
13X5 OUTER NON-CASTER WHL ARM
AFM4011 BOLT-ON SQ HL TB UPGRD
11 OUTSIDE BOLT-ON NONCSTR MNT
11RH INSIDE BOLTON NONCSTR MNT
11LH INSIDE BOLTON NONCSTR MNT
NUT HEX FLG. LOCK 1/2-13 PLT.
HHCS 1/2-13X2 3/4 GR5
(S/N 225160+)
(S/N 225160+)
(S/N 225160+)
(S/N 225160+)
(S/N 225160+)
(S/N 225160+)
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Gauge Wheels
Land Pride
Gauge Wheel Non-Castered (S/N 176349-)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg12656
Drawing Image Number
1.
2.
3.
4.
5.
6.
7.
8.
9.
310-024D
814-117C
310-328D
315-122H
802-350C
315-479D
315-480D
805-126C
818-238C
GAUGE WHEEL SPACER - SHORT
TIRE AIR 10X4 TBLESS, W/HOLES
SPACER TUBE GA. WHL. 5 1/8 LG
NON-CASTER G.W.YOKE AFM133
HHCS 1/2-20X6 1/2 GR5
TUBE 1 1/2X1 1/2X 11GAX 1 PLT
TUBE 1 1/2X1 1/2X 11GAX1/4 PLT
PIN LYNCH 1/4 X 1 3/4 PLT
DECAL TIRES INJECTED W/SEALANT
WASHER LOCK SPRING 1/2 PLT
NUT HEX 1/2-20 PLT
10. 804-015C
11. 803-018C
12. 315-159S
NON-CASTERED G.W.YOKE ASSY
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Gauge Wheels
Land Pride
Gauge Wheel Non-Castered (S/N 176350 to 225159)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg10501
Drawing Image Number
1.
2.
2.
3.
4.
5.
6.
7.
8.
315-292S
814-144C
814-191C
803-025C
315-302H
802-095C
315-479D
315-480D
805-126C
11X4.00 NONCASTER GW YOKE
11 X 400-5 RIB TIRE W 3/4 BRGS
11X400-5 (LITE FOAM) RIB TIRE
NUT HEX 3/4-10 PLT NYLOCK
11X4.00 NONCASTER YOKE
HHCS 3/4-10X7 GR5
TUBE 1 1/2X1 1/2X 11GAX 1 PLT
TUBE 1 1/2X1 1/2X 11GAX1/4 PLT
PIN LYNCH 1/4 X 1 3/4 PLT
Optional foam filled tire
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Gauge Wheels
Land Pride
Gauge Wheel Tire (814-071C) (814-117C)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg13629
Drawing Image Number
1.
1.
2.
3.
4.
814-117C
814-071C
53-182
53-164
53-189
TIRE AIR 10X4 TBLESS, W/HOLES
TIRE 10 X 4 TUBELESS AIR
TILDEN BRG 3/4IDX1 3/8ODX3 1/4
TILDEN RTNR 3/4IDX1 3/8ODX1/4L
TILDEN BRG 3/4ID1.34ODX15/16L
Rims with drain holes
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Gauge Wheels
Land Pride
Gauge Wheel Tire (814-144C) (S/N 225159-) (814-172C) (S/N 225160)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg10499
Drawing Image Number
1.
2.
3.
4.
5.
5.
6.
6.
6.
HSS-34
GS-3
MRTN HGH SPD SPCR3/4ID 1.125OD
MRTN GREASE SEAL 1.125(1.78OD)
BEARING CONE #LM 11949
BEARING CUP #LM 11910
TIRE 13X5 W/HLS & 3/4 ID TAPER BRGS
11 X 400-5 RIB TIRE W 3/4 BRGS
TIRE MARTIN
822-045C
822-050C
814-172C
814-144C
506-4R-I
814-144C
814-172C
(S/N 225160+)
(S/N 225159-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
Gauge Wheel Tire
Gauge Wheel Tire
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Gearboxes
Land Pride
Gearbox 4-Way Splitter (826-124C) Comer (S/N 125860-)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg12659
826-124C
Drawing Image Number
4-WAY SPLITTER BOX 1:1 RATIO
CO SNAP RING EXT 35 UN17435
CO GEAR Z18 M5
RPBY A.259.500
CO SHAFT
CO PARALLEL KEY A 10X8X25
REP BY 822-167C
CO EXTENSION HUB
BEARING BALL 6207
RPBY 822-166C
CO OIL SEAL 35 X 72 X 10
CO CO BOLT M12 X 25 8.8
CO GASKET
1.
2.
3.
4.
5.
6.
7.
8.
8.
9.
8.5.1.00005
0.259.5000.01
0.259.7500.00
0.259.2220.00
8.4.1.00232
8.0.9.00026
0.259.1300.00
822-166C
Rev. 2
Rev. 1
8.0.1.00025
8.7.3.00055
Use up existing stock
10. 8.1.1.00090
11. 0.259.7200.00
12. 8.6.5.00006
13. 0.259.0511.00
14. 8.7.3.00028
15. 0.259.4610.00
16. 0.259.1523.00
17. 8.6.6.00201
CO OIL PLUG 3/8
CO CASING (CASTING)
REP BY 060127
CO SHAFT 1 3/8
CO COVER
CO PLUG 3/8 GAS
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Gearboxes
Land Pride
Gearbox 4-Way Splitter (826-097C) Comer (S/N 125861 to 272759)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg11787
826-097C
Drawing Image Number
RPBY 315-447A
1.
2.
3.
4.
5.
6.
6.
7.
8.
9.
8.1.1.00073
8.3.6.00020
0.257.1743.00
0.242.7200.00
8.7.3.00055
822-166C
8.0.1.00870
0.241.5001.00
0.267.4212.00
8.3.3.00384
CO BOLT M10 X 30 8.8
CO SPRING WASHER 10.2DIN798
CO COVER
CO GASKET
CO OIL SEAL 35 X 72 X 10
BEARING BALL 6207
RPBY 822-166C
CO GEAR Z14 M6.5
CO SHAFT
Rev. 2
Rev 1; Use up stock
CO WASHER M8
10. 0.257.0505.00
11. 0.107.7100.01
12. 8.5.1.00005
13. 8.0.9.00026
14. 8.1.1.00045
15. 8.4.1.00021
16. 0.242.2101.00
17. 0.256.1314.00
18. 8.6.5.00006
19. 0.257.1742.00
20. A.259.500
CO CASTING
CO OIL FILTER PLUG
CO SNAP RING EXT 35 UN17435
REP BY 822-167C
CO BOLT M8 X 10 8.8
CO PARALLEL KEY A 10 X 8 X 35
CO OUTPUT SHAFT
CO EXTENSION
CO OIL PLUG 3/8
CO COVER
CO ADJUSTMENT SPACER, 35.3 X48
CO OIL SEAL 35 X 56 X 8
21. 8.7.3.00071
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Gearboxes
Land Pride
Gearbox 4-Way Splitter (826-274C) OMNI (S/N 272760+)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg18259
826-274C
Drawing Image Number
GBOX DIVIDER OMNI 250559 1:1
OMNI SEAL-THROUGH CAP (3-LIP)
HHCS 5/16-18X1 GR5
WASHER LOCK SPRING 5/16 PLT
OMNI CAP, THRU
OMNI GASKET, CAP 0.10MM
OMNI GASKET, CAP 0.20MM
OMNI GASKET, CAP 0.30MM
OMNI PLUG REL1/2-14NPTF,DPSTCK
OMNI HOUSING, 400 SER. 5B MODI
LOCK NUT, BEARING M30X1.5
LOCKWASHER, BEARING M30
OMNI GEAR, OUTPUT 20T (1:1)
REP BY 050172 CUP
1.
2.
3.
4.
5.
6.
7.
8.
9.
060133
802-159C
804-009C
020166
070218
070219
070220
140055
010180
10. 120126
11. 130146
12. 030512
13. 050170
14. 050172
15. 020164
16. 040345
17. 060134
18. 200142
19. 040343
20. 200141
21. 090099
22. 030467
23. 140004
REP BY 822-167C
OMNI CAP CANTILEVERED
OMNI SHAFT-OUTPUT 1 3/8-6A SPL
OMNI SEAL, CANT. CAP (3-LIP)
OMNI RETAINING RING, 35MM
OMNI SHAFT-INPUT 1 3/8-6A SPL
OMNI RTNG. RING 38MM RC DSH-38
OMNI SPACER
OMNI GEAR, INPUT 20T (1:1)
OMNI PLUG, SOCKET HD. 1/2 PIPE
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Gearboxes
Land Pride
Gearbox Center & Right Deck (826-123C) ITG (S/N 214221-)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg12735
826-327C
826-295C
826-123C
Drawing Image Number
GBOX MOWER 50 HP 1:2.8 CCW
RPBY 826-327C
Rev. 3
Rev. 2
Rev. 1
RPBY 826-205C
1.
2.
2.
3.
4.
5.
6.
7.
8.
9.
18-010
822-166C
04-004
09-002
02-034
21-012
03-043
08-004A
08-004B
07-001
ITG HOUSING
BEARING BALL 6207
RPBY 822-166C
REP BY 140000
Rev. 2
Rev 1; Use up stock
ITG INPUT SHAFT
ITG RETAINING RING
ITG 34 TOOTH INPUT GEAR
ITG INPUT CAP GASKET 0.25MM
ITG INPUT CAP GASKET 0.10MM
RPBY 804-158C
10. 06-012
11. 20-007
12. 09-009
13. 08-005A
14. 08-005B
15. 20-003
16. 05-005
17. 805-017C
18. 11-007
19. 07-007
20. 03-042
21. 10-002
22. 04-003
23. 05-002
24. 310-331D
25. 16-013
ITG M10 X 1.5 X 25 CAP SCREW
ITG INPUT CAP
ITG CAP PLUG
ITG OUTPUT CAP GASKET 0.25MM
ITG OUTPUT CAP GASKET 0.10MM
ITG OUTPUT CAP
ITG OUTPUT OIL SEAL
PIN COTTER 3/16 X 1 3/4 PLT
ITG 1"-14 SLOTTED HEX NUT
ITG WASHER
ITG 12 TOOTH OUTPUT PIN & SHFT
ITG BEARING SPACER
REP BY 822-188C
ITG INPUT OIL SEAL
KEY 1/4" X 11/16" LONG
REP BY 8.6.7.00269
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Gearboxes
Land Pride
Gearbox Center & Right Deck (826-205C) OMNI (S/N 214222 to 340848)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg16506
826-205C
Drawing Image Number
RC-25 1:2.8 CCW 90 BOX(RC25HS)
OMNI SCREW-5/16"-18UNC X 7/8"
REP BY 804-009C
1.
2.
3.
4.
5.
6.
7.
8.
9.
110192
130006
020224
070249
070248
070247
070246
060127
050170
OMNI CAP-INPUT
OMNI GASKET-INPUT 0.50MM
OMNI GASKET-INPUT 0.30MM
OMNI GASKET-INPUT 0.20MM
OMNI GASKET-INPUT 0.10MM
OMNI SEAL-INPUT CR13930
REP BY 050172 CUP
10. 050172
11. 040335
12. 030457
13. 200141
14. 200140
15. 090181
16. 090180
17. 090179
18. 110009
19. 130028
20. 240280
21. 010175
22. 140047
23. 140000
23. 140033
23. 8.6.7.00269
24. 030456
25. 090182
26. 090183
27. 090184
28. 050197
29. 050195
30. 090185
31. 090186
32. 090187
33. 090188
34. 200000
35. 070250
36. 070251
37. 070252
38. 070253
39. 060128
40. 020225
41. 120050
42. 100001
43. 140017
REP BY 822-167C
OMNI SHAFT-INPUT 1-3/8"-6 SPLN
OMNI GEAR INPUT, 34T
OMNI RTNG. RING 38MM RC DSH-38
OMNI RTNG. RING 38MM RC DSH-38
OMNI SHIM INPUT 0.30MM
OMNI SHIM INPUT 0.20MM
REP BY 090180
OMNI SCREW-1/4"-20 UNC X 3/4"
OMNI LOCKWASHR 1/4" SPLIT TYPE
OMNI INSPECTION COVER
OMNI HOUSING-RC-25
OMNI PLUG SQ.HD.1/2-14NPT W/DP
OMNI PIPE PLUG 1/2' SQ HEAD
OMNI PLUG VENT 1/2-14 NPTF
CO 1/2" GAS BREATHER PLUG
OMNI PINION-OUTPUT 12T
OMNI SHIM OUTPUT 0.10MM
OMNI SHIM OUTPUT 0.20MM
OMNI SHIM OUTPUT 0.30MM
REP BY 822-191C
(S/N 215411+)
(S/N 215410-) 3-5 Lbp.
7.5-15 Lbs. (Owners Choice)
Rev. 2 not compat. w/Rev. 1
Rev. 1
REP BY 050197 CUP
OMNI SPACER OUTPUT
OMNI SHIM OUTPUT 0.10MM
OMNI SHIM OUTPUT 0.20MM
OMNI SHIM OUTPUT 0.30MM
OMNI RETAINING RING
OMNI GASKET-OUTPUT 0.10MM
OMNI GASKET-OUTPUT 0.20MM
OMNI GASKET-OUTPUT 0.30MM
OMNI GASKET-OUTPUT 0.50MM
OMNI SEAL-OUTPUT CR15822
OMNI CAP-OUTPUT
OMNI NUT HEX SLOTTED, 1-14UNC
OMNI COTTER PIN 5 X 50
OMNI PLUG PIPE SQ HD1/8-27NPTF
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Gearboxes
Land Pride
Gearbox Center & Right Deck (826-295C) OMNI (S/N 214222 to 340848)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg18641
826-295C
Drawing Image Number
RC-25 1:2.8 CCW 90 BOX(RC25HS)
OMNI SCREW-5/16"-18UNC X 7/8"
REP BY 804-009C
1.
2.
3.
4.
5.
6.
7.
8.
9.
110192
130006
020224
070249
070248
070247
070246
060127
050170
OMNI CAP-INPUT
OMNI GASKET-INPUT 0.50MM
OMNI GASKET-INPUT 0.30MM
OMNI GASKET-INPUT 0.20MM
OMNI GASKET-INPUT 0.10MM
OMNI SEAL-INPUT CR13930
REP BY 050172 CUP
10. 050172
11. 040491
12. 030457
13. 200141
14. 200140
15. 090181
16. 090180
17. 090179
18. 110009
19. 130028
20. 240280
21. 010252
22. 140047
23. 140000
24. 030456
25. 090182
26. 090183
27. 090184
28. 050197
29. 050195
30. 090185
31. 090186
32. 090187
33. 090188
34. 200000
35. 070250
36. 070251
37. 070252
38. 070253
39. 060128
40. 020225
41. 120050
42. 100001
43. 140017
44. 090341
REP BY 822-167C
OMNI SHAFT INPUT 1 3/8" - 6A
OMNI GEAR INPUT, 34T
OMNI RTNG. RING 38MM RC DSH-38
OMNI RTNG. RING 38MM RC DSH-38
OMNI SHIM INPUT 0.30MM
OMNI SHIM INPUT 0.20MM
OMNI SHIM INPUT 0.10MM
OMNI SCREW-1/4"-20 UNC X 3/4"
OMNI LOCKWASHR 1/4" SPLIT TYPE
OMNI INSPECTION COVER
OMNI HOUSING RC-25 SERIES
OMNI PLUG SQ.HD.1/2-14NPT W/DP
OMNI PIPE PLUG 1/2' SQ HEAD
OMNI PINION-OUTPUT 12T
OMNI SHIM OUTPUT 0.10MM
OMNI SHIM OUTPUT 0.20MM
OMNI SHIM OUTPUT 0.30MM
REP BY 822-191C
REP BY 050197 CUP
OMNI SPACER OUTPUT
OMNI SHIM OUTPUT 0.10MM
OMNI SHIM OUTPUT 0.20MM
OMNI SHIM OUTPUT 0.30MM
OMNI RETAINING RING
OMNI GASKET-OUTPUT 0.10MM
OMNI GASKET-OUTPUT 0.20MM
OMNI GASKET-OUTPUT 0.30MM
OMNI GASKET-OUTPUT 0.50MM
OMNI SEAL-OUTPUT CR15822
OMNI CAP-OUTPUT
OMNI NUT HEX SLOTTED, 1-14UNC
OMNI COTTER PIN 5 X 50
OMNI PLUG PIPE SQ HD1/8-27NPTF
OMNI SPACER, INPUT
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Gearboxes
Land Pride
Gearbox Center & Right Deck (826-327C) Comer Service Only
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg19550
826-327C
Drawing Image Number
GBOX MOWER 50 HP 1:2.8 CCW
CO OIL PLUG 3/8
CO BOLT M8X22 HHB
CO COVER
CO INPUT SHAFT 1" 3/8 Z6
CO CAP 72 X 10
CO SNAP RING INT 72 UN17437
COMER SHIM KIT 71.7
1.
2.
3.
4.
5.
6.
7.
8.
9.
8.6.5.00006
8.1.1.00501
0.195.1300.00
0.195.2000.00
8.7.0.00744
8.5.2.00131
A.248.500
822-166C
8.5.1.00680
BEARING BALL 6207
CO SNAP RING 40 UNI 7436
CO SHIM 35.3 X 48 X 2.5
CO HOUSING
CO ROLLER BEARING 32208 CL-B
CO NUT M40 X 1.5
CO OIL SEAL 35 X 80 X 10 RTA35
CO PROTECTIVE FLAT WASHER
CO SNAP RING SB 81
CO FLAT WASHER 25 X 44 X 4
NUT CASTLE M 24 X 2
CO COTTER PIN B5 X 50
CO SHIM 40.3 X 51.5 826-067C
CO PINION Z12 M4.7
CO ROLLER BEARING 30207 CL-B
CO OIL SEAL 35 X 72 X 10
CO CROWN GEAR Z33 M4.7
10. 0.259.7525.00
11. 0.195.0300.00
12. 8.0.9.00102
13. 0.278.7103.00
14. 8.7.3.00081
15. 1.195.7100.00
16. 8.5.3.00955
17. 8.3.2.00409
18. 8.2.2.01144
19. 8.4.7.00516
20. A244.501
21. 0.195.5000.00
22. 8.0.9.00026
23. 8.7.3.00055
24. 0.195.6000.00
25. U0.195.7101.00 CO OIL LEVEL PLUG 3/8" GAS
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Gearboxes
Land Pride
Gearbox Left Deck (826-085C) IEG (S/N 214221-)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg10891
826-085C
Drawing Image Number
RPBY 826-204C & 826-206C
ITG GEARBOX HOUSING
BEARING BALL 6207
RPBY 822-166C
REP BY 140000
ITG INPUT SHAFT
ITG RETAINING RING
ITG 34 TOOTH INPUT GEAR
ITG INPUT CAP GASKET 0.25MM
ITG INPUT CAP GASKET 0.10MM
RPBY 804-158C
1.
2.
2.
3.
4.
5.
6.
7.
8.
9.
18-021
822-166C
04-004
09-002
02-034
21-012
03-043
08-004A
08-004B
07-001
Rev. 2
Rev 1; Use up stock
10. 06-012
11. 20-007
12. 09-009
13. 08-005A
14. 08-005B
15. 20-003
16. 05-005
17. 805-017C
18. 11-007
19. 07-007
20. 03-042
21. 10-002
22. 04-003
23. 05-002
24. 310-331D
25. 16-013
26. 811-320C
ITG M10 X 1.5 X 25 CAP SCREW
ITG INPUT CAP
ITG CAP PLUG
ITG OUTPUT CAP GASKET 0.25MM
ITG OUTPUT CAP GASKET 0.10MM
ITG OUTPUT CAP
ITG OUTPUT OIL SEAL
PIN COTTER 3/16 X 1 3/4 PLT
ITG 1"-14 SLOTTED HEX NUT
ITG WASHER
ITG 12 TOOTH OUTPUT PIN & SHFT
ITG BEARING SPACER
REP BY 822-188C
ITG INPUT OIL SEAL
KEY 1/4" X 11/16" LONG
REP BY 8.6.7.00269
SP SAFETY VALVE 1/8MNPT
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Gearboxes
Land Pride
Gearbox Left Deck (826-206C) OMNI (S/N 214222 to 340848)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg15934
826-206C
Drawing Image Number
RC-25 1:2.8 CW 90 BOX(RC25HR)
OMNI SCREW-5/16"-18UNC X 7/8"
REP BY 804-009C
1.
2.
3.
4.
5.
6.
7.
8.
9.
110192
130006
020224
070249
070248
070247
070246
060127
050170
OMNI CAP-INPUT
OMNI GASKET-INPUT 0.50MM
OMNI GASKET-INPUT 0.30MM
OMNI GASKET-INPUT 0.20MM
OMNI GASKET-INPUT 0.10MM
OMNI SEAL-INPUT CR13930
REP BY 050172 CUP
10. 050172
11. 200140
12. 040335
13. 200141
14. 030457
15. 090181
16. 090180
17. 090179
18. 110009
19. 130028
20. 240280
21. 010175
22. 140047
23. 140000
23. 140033
23. 8.6.7.00269
24. 030456
25. 090182
26. 090183
27. 090184
28. 050197
29. 050195
30. 090185
31. 090186
32. 090187
33. 090188
34. 200000
35. 070250
36. 070253
37. 070252
38. 070251
39. 060128
40. 020225
41. 120050
42. 100001
43. 140017
REP BY 822-167C
OMNI RTNG. RING 38MM RC DSH-38
OMNI SHAFT-INPUT 1-3/8"-6 SPLN
OMNI RTNG. RING 38MM RC DSH-38
OMNI GEAR INPUT, 34T
OMNI SHIM INPUT 0.30MM
OMNI SHIM INPUT 0.20MM
OMNI SHIM INPUT 0.10MM
OMNI SCREW-1/4"-20 UNC X 3/4"
OMNI LOCKWASHR 1/4" SPLIT TYPE
OMNI INSPECTION COVER
OMNI HOUSING-RC-25
OMNI PLUG SQ.HD.1/2-14NPT W/DP
OMNI PIPE PLUG 1/2' SQ HEAD
OMNI PLUG VENT 1/2-14 NPTF
CO 1/2" GAS BREATHER PLUG
OMNI PINION-OUTPUT 12T
OMNI SHIM OUTPUT 0.10MM
OMNI SHIM OUTPUT 0.20MM
OMNI SHIM OUTPUT 0.30MM
REP BY 822-191C
(S/N 215411+) 3-5 Lbs.
(S/N 215410-)
7.5-15 Lbs. (Owner choice)
Rev. 2 not compat. w/Rev. 1
Rev. 1
REP BY 050197 CUP
OMNI SPACER OUTPUT
OMNI SHIM OUTPUT 0.10MM
OMNI SHIM OUTPUT 0.20MM
OMNI SHIM OUTPUT 0.30MM
OMNI RETAINING RING
OMNI GASKET-OUTPUT 0.10MM
OMNI GASKET-INPUT 0.50MM
OMNI GASKET-INPUT 0.30MM
OMNI GASKET-INPUT 0.20MM
OMNI SEAL-OUTPUT CR15822
OMNI CAP-OUTPUT
OMNI NUT HEX SLOTTED, 1-14UNC
OMNI COTTER PIN 5 X 50
OMNI PLUG PIPE SQ HD1/8-27NPTF
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Gearboxes
Land Pride
Gearbox Left Deck (826-296C) OMNI (S/N 214222 to 340848)
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg18948
826-296C
Drawing Image Number
Gearbox OMNI Left Hand Deck
OMNI SCREW-5/16"-18UNC X 7/8"
REP BY 804-009C
1.
2.
3.
4.
5.
6.
7.
8.
9.
110192
130006
020224
070249
070248
070247
070246
060127
050170
OMNI CAP-INPUT
OMNI GASKET-INPUT 0.50MM
OMNI GASKET-INPUT 0.30MM
OMNI GASKET-INPUT 0.20MM
OMNI GASKET-INPUT 0.10MM
OMNI SEAL-INPUT CR13930
OMNI BEARING CUP 30207
OMNI BEARING CONE 30207
OMNI RTNG. RING 38MM RC DSH-38
OMNI SHAFT-INPUT 1-3/8"-6 SPLN
OMNI RTNG. RING 38MM RC DSH-38
OMNI GEAR INPUT, 34T
OMNI SHIM INPUT 0.30MM
OMNI SHIM INPUT 0.20MM
REP BY 090180
OMNI SCREW-1/4"-20 UNC X 3/4"
OMNI LOCKWASHR 1/4" SPLIT TYPE
OMNI INSPECTION COVER
OMNI HOUSING-RC-25
OMNI PLUG SQ.HD.1/2-14NPT W/DP
OMNI PIPE PLUG 1/2' SQ HEAD
OMNI PLUG VENT 1/2-14 NPTF
CO 1/2" GAS BREATHER PLUG
OMNI PINION-OUTPUT 12T
REP BY 090183
OMNI SHIM OUTPUT 0.20MM
OMNI SHIM OUTPUT 0.30MM
REP BY 822-191C
10. 050172
11. 200140
12. 040491
13. 200141
14. 030457
15. 090181
16. 090180
17. 090179
18. 110009
19. 130028
20. 240280
21. 010252
22. 140047
23. 140000
23. 140033
23. 8.6.7.00269
24. 030456
25. 090182
26. 090183
27. 090184
28. 050197
29. 050195
30. 090185
31. 090186
32. 090187
33. 090188
34. 200000
35. 070250
36. 070251
37. 070252
38. 070253
39. 060128
40. 020225
41. 120050
42. 100001
43. 140017
44. 090341
(S/N 215411+) 3-5 Lbs.
(S/N 215410-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
7.7-15 Lbs. (Owners choice)
REP BY 050197 CUP
OMNI SPACER OUTPUT
OMNI SHIM OUTPUT 0.10MM
OMNI SHIM OUTPUT 0.20MM
OMNI SHIM OUTPUT 0.30MM
OMNI RETAINING RING
OMNI GASKET-OUTPUT 0.10MM
OMNI GASKET-OUTPUT 0.20MM
OMNI GASKET-OUTPUT 0.30MM
OMNI GASKET-OUTPUT 0.50MM
OMNI SEAL-OUTPUT CR15822
OMNI CAP-OUTPUT
OMNI NUT HEX SLOTTED, 1-14UNC
OMNI COTTER PIN 5 X 50
OMNI PLUG PIPE SQ HD1/8-27NPTF
OMNI SPACER, INPUT
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Gearboxes
Land Pride
Gearbox Left Deck (826-326C) Comer Service Only
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg19549
826-326C
Drawing Image Number
GBOX MOWER 50 HP 1:2.8 CW
CO OIL PLUG 3/8
CO BOLT M8X22 HHB
CO COVER
1.
2.
3.
4.
5.
6.
7.
8.
9.
8.6.5.00006
8.1.1.00501
0.195.1300.00
0.195.2000.00
8.7.0.00744
8.5.2.00131
A.248.500
CO INPUT SHAFT 1" 3/8 Z6
CO CAP
72 X 10
CO SNAP RING INT 72 UN17437
COMER SHIM KIT 71.7
CO ROLLER BEARING 30207 CL-B
CO SNAP RING 40 UNI 7436
CO SHIM 35.3 X 48 X 2.5
CO HOUSING
CO ROLLER BEARING 32208 CL-B
CO NUT M40 X 1.5
CO OIL SEAL 35 X 80 X 10 RTA35
CO PROTECTIVE FLAT WASHER
CO SNAP RING SB 81
CO FLAT WASHER 25 X 44 X 4
NUT CASTLE M 24 X 2
CO COTTER PIN B5 X 50
CO SHIM 40.3 X 51.5 826-067C
CO PINION Z12 M4.7
8.0.9.00026
8.5.1.00680
10. 0.259.7525.00
11. 0.195.0300.00
12. 8.0.9.00102
13. 0.278.7103.00
14. 8.7.3.00081
15. 1.195.7100.00
16. 8.5.3.00955
17. 8.3.2.00409
18. 8.2.2.01144
19. 8.4.7.00516
20. A244.501
21. 0.195.5000.00
22. 822-166C
BEARING BALL 6207
23. 8.7.3.00055
24. 0.195.6000.00
CO OIL SEAL 35 X 72 X 10
CO CROWN GEAR Z33 M4.7
25. U0.195.7101.00 CO OIL LEVEL PLUG 3/8" GAS
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Hydraulics
Land Pride
Folding Hydraulics
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg13562
Drawing Image Number
1.
2.
3.
4.
5.
6.
7.
7.
8.
9.
810-150C
811-447C
811-445C
811-444C
811-442C
811-443C
811-119C
811-332C
811-119C
810-005C
CYL 2.5X12X1.25 ROD (TIE ROD)
ORPL 1/32 9/16MORB
HH1/4R2 035 9/16FJIC 3/8MORB90
HH1/4R2 020 9/16FJIC 3/8MORB90
HH1/4R2 028 9/16FJIC
HH1/4R2 036 9/16FJIC
EL 3/8MNPT 9/16MJIC
OREL 1/32 9/16MJIC 3/8MNPT
EL 3/8MNPT 9/16MJIC
CYL 2X8X1.12 ROD SINGLE ACTING
CP 3/4FORB MALE QD
HH1/4R2 096 9/16FJIC 3/4 MORB
HHCS 1/4-20X4 GR5
HHCS 1/4-20X3 1/4 GR5
WASHER LOCK SPRING 1/4 PLT
NUT HEX 1/4-20 PLT
SPCR 1/2 OD X .28ID X 1 3/8
SPCR 1/2 OD X .28 ID X 5/8
AD 9/16MORB 9/16MJIC
SP-8 PORT RELIEF 9/16-18FORB (S/N
176350+)
SP 4 PORT MANIFOLD 9/16-18MJIC
CABLE TIE .19X14.25 3DIA 50LB
SPRING HOSE LOOP
(S/N 233151-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
10. 811-394C
11. 811-441C
12. 802-451C
12. 802-308C
13. 804-006C
14. 803-006C
15. 315-743D
15. 315-492D
16. 811-170C
17. 811-495C
Rev. 2
Rev 1; Use up stock
Rev. 2
Rev 1; Use up stock
Rev. 2 not compat. w/Rev. 1
Rev. 1
17. 811-438C
18. 800-060C
19. 807-023C
20. 802-079C
21. 804-012C
22. 804-013C
23. 803-014C
24. 8026
(S/N 176349-)
(S/N 176350+)
(S/N 176350+)
(S/N 176350+)
(S/N 176350+)
(S/N 176350+)
HHCS 3/8-16X1 1/4 GR5
WASHER FLAT 3/8 SAE PLT
WASHER LOCK SPRING 3/8 PLT
NUT HEX 3/8-16 PLT
SHMKR CRTRDG RELIEF VALVE ASSY
RPBY 8026
Rev. 2
Rev 1; Use up stock
24. 1497
25. 805-004C
26. 805-088C
27. 811-694C
27. 811-170C
PIN CLEVIS 1 X 2 3/4 USABLE LG
PIN, HAIR COTTER 3/16 WIRE DIA
ORAD 1/32 9/16MORB 9/16MJIC
AD 9/16MORB 9/16MJIC
(S/N 233152+)
(S/N 233151-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Hydraulics
Land Pride
Hydraulic Cylinder (810-150C) Midway
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg11421
810-150C
6M3118
1D1505-3
2A0012
Drawing Image Number
CYL 2.5X12X1.25 ROD (TIE ROD)
MW BASE
1.
1.
2.
2.
3.
4.
4.
5.
5.
6.
6.
7.
7.
8.
8.
9.
9.
BASE CROSS
MW NUT CLEVIS & TIE ROD
CROSS NUT, CLEVIS & TIE ROD
O-RING
2A0235-6
Only found in seal kit 19.
7M3320
2A0578-1675
5M3120
1D0005-1450
2A0006
2A0079-616
2A0208
1D1551-16275 CROSS CLEVIS PIN
2A0132
2A0308-1
1M6010
1D1003-5
MW TIE ROD
TIE ROD CROSS
MW TUBE
TUBE CROSS
REPL. BY 802-023C
CROSS SCREW, CAP
MW CLEVIS PIN
MW PIN CLIP
REP BY 805-032C
MW CLEVIS STD. DUTY
CROSS ROD CLEVIS
MW NUT CLEVIS & TIE ROD
CROSS NUT, CLEVIS & TIE ROD
MW ROD
ROD CROSS
WIPER
BACKUP ROD
O-RING
10. 2A0012
10. 2A0235-6
11. 2M3418
11. 1D0206-1675
12.
Only found in seal kit 19.
Only found in seal kit 19.
Only found in seal kit 19.
13.
14.
15. 3M3406
15. 1D1155-17
16.
17. 4M3102
17. 1D1401-250
18. 2A0022
18. 2A0246-12
19. 810-177C
19. 810-178C
MW HEAD
HEAD CROSS
BACKUP PISTON
REPL. BY 4M3108
PISTON CROSS
MW NUT, PISTON
CROSS NUT, PISTON
SEAL KIT MW 2.5X1.25ROD 3A3104
SEAL KIT CROSS 2.5 CYL 1C4982
Only found in seal kit 19.
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Hydraulics
Land Pride
Hydraulic Cylinder (810-150C) Red Lion
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg25899
810-150C
Drawing Image Number
CYL 2.5X12X1.25 ROD (TIE ROD)
*
1.
2.
3.
4.
5.
6.
7.
8.
9.
803-014C
130556
134953
135995
801-023C
186561
N/A
NUT HEX 3/8-16 PLT
MON PISTON NUT
LION PIN
MON CLEVIS PIN COTTER
SCREW SET SH 3/8-16X3/8 TYPE C
PLUG 9/16-18UNF MORB SOCKET HD
MON ROD SEAL
Only Found in Kit #20
Only Found in Kit #20
Only Found in Kit #20
Only Found in Kit #20
Only Found in Kit #20
Only Found in Kit #20
N/A
N/A
MON PISTON SEAL
MON END CAP BACKUP WASHERS
MON END CAP O-RING
SEAL WIPER ROD
MON PISTON WEAR RING
LION CYL TUBE 2.5 X 12
LION TIE ROD 3/8, 12 CYL
LION ROD 1.25 X 12
LION ROD CLEVIS 1 1/8-12UNF
LION CLEVIS CAP 2.5, 9/16 ORB
LION ROD CAP 2.5X1.25 9/16 ORB
MON PISTON
10. N/A
11. N/A
12. N/A
13. 491672
14. 492222
15. 492647
16. 492650
17. 492688
18. 492724
19. 494768
20. 645004
MON SEALS REPAIR KIT
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 8: Labels
Land Pride
Label Placement
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg17590
Drawing Image Number
1.
1.
2.
3.
4.
5.
6.
7.
7.
7.
8.
9.
818-892C
818-165C
818-190C
818-448C
818-449C
818-138C
818-298C
818-919C
818-713C
818-567C
818-450C
818-488C
DECAL LP W/TREE 10" - 3 COLOR
LP LOGO SMALL BUCKSKIN
DECAL FLAG
DECAL PTO 826-125C
DECAL PTO 826-126C
DECAL GREASE EVERY 25 HOURS
DECAL GREASE 25HRS BLACK/WHITE
DECAL AFM4011-BROWN
DECAL AFM4011 LP BLACK
DECAL 40133 -LP BLACK
(S/N 253841+)
(S/N 253840-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
(S/N 253841+)
(S/N 231068 <-> 253840)
(S/N 231067-)
Rev. 3 not compat. w/Rev. 2
Rev. 2 not compat. w/Rev. 1
Rev. 1
DECAL PTO 826-127C
DECAL PTO MAINTENANCE CV
DECAL NOTICE TO OWNER-NO WARRA
RPBY 818-560C 1st revision
DECAL IMPORTANT - SLIP CLUTCH
DECAL LANDPRIDE 6"- BEIGE
LP LOGO SMALL BUCKSKIN
10. 818-560C
10. 818-559C
11. 818-680C
12. 838-036C
12. 818-165C
Rev. 2 not compat. w/Rev. 1
Rev. 1
(S/N 253841+)
(S/N 253840-)
Rev. 2 not compat. w/Rev. 1
Rev. 1
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 8: Labels
Land Pride
Safety Label Placement
Applies to AFM4011 and AFM40133
Ref. Part No.
Part Description
Comments
Revision
dwg10504
Drawing Image Number
1.
2.
3.
4.
5.
6.
7.
8.
9.
818-019C
818-339C
818-558C
818-229C
818-552C
818-351C
818-293C
818-130C
818-556C
DECAL WARNING NEG TONGUE WT
DECAL WARNING HIGH PRESSUR SML
DECAL WARNING GEN SAFE MOWER
DECAL AMBER REFLECTOR
DECAL DANGER PTO DRIVELINE
DECAL CAUTION TRANSP LOCK ENGD
DECAL CAUTION V-BELT INST 1548
DECAL CAUTION 540 RPM
DECAL DANGER THROWN OBJ CUTTER
DECAL DANGER ROTATE BLADE
DECAL DANGER DRIVELINE SHIELD
DECAL RED REFLECTOR
DECAL WARNING 20 MPH TRANS SML
DECAL CAUTION TRANSP LOCK DISE
DECAL CAUTION V-BELT INST 48
DECAL DANGER CANNOT READ ENG
DECAL DANGER RAISED WING HAZAR
DECAL DANGER GUARD MISS PTO
DECAL SLOW MOVING-GALV. BACKED
DECAL WARNING PINCH PT/CRUSH
DECAL DANGER PD GUARD MISS SML
10. 818-555C
11. 818-187C
12. 818-230C
13. 818-337C
14. 818-353C
15. 818-456C
16. 818-557C
17. 818-561C
18. 818-540C
19. 818-055C
20. 818-045C
21. 818-543C
Beneath all belt guards (S/N
253841+)
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Number Index
The Part Number Index is a numeric index of all part numbers included in this manual. The index shows what page(s) the part is used on.
Part Number
Page
Part Number
Page
Part Number
Page
Part Number
Page
0.107.7100.01 ...........71
0.241.5001.00 ...........71
0.242.2101.00 ...........71
0.242.7200.00 ...........71
0.256.1314.00 ...........71
0.257.0505.00 ...........71
0.257.1742.00 ...........71
0.257.1743.00 ...........71
0.259.0511.00 ...........69
0.259.1300.00 ...........69
0.259.1523.00 ...........69
0.259.2220.00 ...........69
0.259.4610.00 ...........69
0.259.5000.01 ...........69
0.259.7200.00 ...........69
0.259.7500.00 ...........69
0.267.4212.00 ...........71
010180 ......................73
020164 ......................73
020166 ......................73
020616 ......................21
020672 ......................21
020692 ......................25
030467 ......................73
030512 ......................73
040343 ......................73
040345 ......................73
041068 ......................23
041180 ......................25
041577 ......................21
043487 ......................25
044444 ......................21
045790 ......................25
045793 ......................25
047825 ......................25
048755 ......................19
060133 ......................73
060134 ......................73
070218 ......................73
070219 ......................73
070220 ......................73
087276 ......................21
196839 ......................21
1D0005-1450 .............93
1D0206-1675 .............93
1D1003-5 ...................93
1D1155-17 .................93
1D1401-250 ...............93
1D1505-3 ...................93
1D1551-16275 ...........93
1M6010 .....................93
315-004H ...................13
315-037V ...................41
315-098H ...................59
315-120H ...................47
315-122H ...................61
315-124H ...................57
315-125H ...................57
315-126H ...................57
315-127H ...................57
315-130H ...................53
315-131H ...................53
200142 ......................73
2A0006 ......................93
2A0012 ......................93
2A0022 ......................93
2A0079-616 ...............93
2A0132 ......................93
2A0208 ......................93
2A0235-6 ...................93
2A0246-12 .................93
2A0308-1 ...................93
2A0578-1675 .............93
2M3418 .....................93
304149 ......................25
315-133H ...................47
315-134H ...................11
315-135H ...................11
315-136H ...................7
315-137H ...................11
315-139H ...................13
315-142H ...................11
315-144H ...................7
315-145H ...................17
315-147H ...................13
315-151H ...................41
315-153A ...................11
315-155A ...................11
315-157S ...................57
315-158S ...................43
315-166S ...................9
315-169S ...................29
315-175H ...................7
315-176S ...................29
315-183H ...................7
315-197H ...................13
315-234D ...................47
315-245D ...................59
315-246D ...................59
315-247D ...................59
315-248D ...................59
315-270H ...................57
315-271H ...................57
315-274H ...................13
315-276H ...................41
315-277H ...................13
315-281H ...................47
315-294S ...................57
090099 ......................73
10-097 .......................15
310-132S ...................33
120126 ......................73
130146 ......................73
130556 ......................95
134953 ......................95
135995 ......................95
140004 ......................73
140055 ......................73
1497 ..........................91
168556 ......................25
310-149H ...................49
310-248S ...................37
310-319H ...................47
310-352S ...................39
310-454D ...................37
310-533D ...................47
310-630D ...................37
315-300H ...................51
315-301H ...................57
315-302H ...................63
315-333H ...................53
315-334H ...................53
315-369H ...................13
315-391H ...................41
315-393H ...................59
315-394H ...................59
315-395H ...................59
051551 ......................25
175-061D ...................7
18-010 .......................75
18-021 .......................83
180909 ......................23
186561 ......................95
100
AFM4011 And AFM40133 All-Flex Mower 315-470P
04/02/08
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Number Index (continued)
Part Number
Page
Part Number
Page
Part Number
Page
Part Number
Page
315-396H ...................59
315-397H ...................55
315-399D ...................53
315-400S ...................59
315-401H ...................55
315-402S ...................59
315-409D ...................47
315-411H ...................41
315-449H ...................13
315-452E ...................13
315-453E ...................13
315-459A ...................13
315-478D ...................41
315-481D ...................47
315-485D ...................11
315-486D ...................11
315-487D ...................7
315-492D ...................91
315-494A ...................59
315-498H ...................59
315-499H ...................59
315-500H ...................59
315-543D ...................55
315-544D ...................55
315-618D ...................47
315-743D ...................91
315-753D ...................13
315-754D ...................13
315-768D ...................13
315-776D ...................47
315-789D ...................47
319624 ......................21
338531 ......................25
341953 ......................25
355155 ......................21
366862 ......................21
377335 ......................21
380906 ......................21
381495 ......................25
381957 ......................25
382701 ......................21
382710 ......................21
384488 ......................19
384517 ......................21
385365 ......................23
386163 ......................21
386424 ......................23
388954 ......................21
388957 ......................21
389961 ......................21
389965 ......................19
390001 ......................23
390002 ......................19
392045 ......................19
392046 ......................19
392047 ......................23
392048 ......................23
392049 ......................23
3M3406 .....................93
401-372D ...................13
491672 ......................95
492107 ......................15
492222 ......................95
492647 ......................95
492650 ......................95
492688 ......................95
492724 ......................95
494768 ......................95
4M3102 .....................93
506-4R-I ....................67
518081 ......................15
53-164 .......................65
53-182 .......................65
53-189 .......................65
5M3120 .....................93
645004 ......................95
6M3118 .....................93
7M3320 .....................93
8.0.1.00025 ...............69
8.0.1.00870 ...............71
8.1.1.00045 ...............71
8.1.1.00073 ...............71
8.1.1.00090 ...............69
8.3.3.00384 ...............71
8.3.6.00020 ...............71
8.4.1.00021 ...............71
8.4.1.00232 ...............69
8.6.6.00201 ...............69
8.7.3.00028 ...............69
8.7.3.00071 ...............71
803-169C ...................59
803-231C ...................47
803-293C ...................41
804-009C ...................73
802-058C ...................57
802-060C ...................13
802-074C ...................13
802-075C ...................13
802-114C ...................13
802-125C ...................15
802-159C ...................73
802-204C ...................11
802-205C ...................13
802-226C ...................59
802-235C ...................13
802-308C ...................91
802-360C ...................13
802-444C ...................17
802-451C ...................91
802-458C ...................17
8026 ..........................91
803-005C ...................41
803-013C ...................13
804-019C ...................13
804-023C ...................13
804-027C ...................13
804-028C ...................13
805-023C ...................7
805-081C ...................13
805-109C ...................13
805-142C ...................11
805-177C ...................57
805-228C ...................7
806-047C ...................53
807-023C ...................91
807-176C ...................41
803-019C ...................47
800-060C ...................91
810-177C ...................93
810-178C ...................93
811-119C ...................91
811-170C ...................91
811-320C ...................83
811-332C ...................91
811-394C ...................91
811-438C ...................91
811-441C ...................91
811-442C ...................91
811-443C ...................91
811-444C ...................91
811-445C ...................91
811-447C ...................91
811-495C ...................91
800-114C ...................47
800-115C ...................47
800-116C ...................47
800-136C ...................11
800-163C ...................47
801-018C ...................41
801-023C ...................95
802-005C ...................41
802-024C ...................53
802-041C ...................47
803-026C ...................11
803-027C ...................13
803-031C ...................13
803-038C ...................13
803-053C ...................15
803-148C ...................13
803-159C ...................15
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Number Index (continued)
Part Number
Page
Part Number
Page
Part Number
Page
811-694C ...................91
814-118C ...................15
815-001C ...................15
815-104C ...................15
816-014C ...................15
dwg16679 ..................55
dwg16680 ..................59
dwg17278 ..................27
dwg17279 ..................39
dwg17280 ..................37
dwg17590 ..................97
dwg18259 ..................73
dwg18641 ..................79
dwg18948 ..................87
dwg19549 ..................89
dwg19550 ..................81
816-298C ...................41
817-082C ...................47
817-192C ...................47
817-195C ...................47
817-259C ...................47
818-019C ...................99
818-045C ...................99
818-130C ...................99
818-138C ...................97
818-165C ...................97
818-187C ...................99
818-190C ...................97
818-229C ...................99
818-230C ...................99
818-293C ...................99
818-298C ...................97
818-337C ...................99
818-339C ...................99
818-351C ...................99
818-353C ...................99
818-456C ...................99
818-488C ...................97
818-543C ...................99
818-555C ...................99
818-556C ...................99
818-557C ...................99
818-558C ...................99
818-559C ...................97
818-560C ...................97
818-561C ...................99
818-567C ...................97
818-680C ...................97
818-713C ...................97
818-892C ...................97
818-919C ...................97
838-036C ...................97
890-005C ...................11
890-118C ...................13
890-182C ...................13
890-332C ...................9
GS-3 ..........................67
HSS-34 ......................67
N/A ............................95
TR-412 ......................15
890-337C ...................9
890-589C ...................9
890-614C ...................15
A.259.500 ..................71
dwg10499 ..................67
dwg10500 ..................51
dwg10501 ..................63
dwg10504 ..................99
dwg10600 ..................25
dwg10891 ..................83
dwg11421 ..................93
dwg11787 ..................71
dwg12645 ..................15
dwg12647 ..................11
dwg12648 ..................53
dwg12652 ..................47
dwg12653 ..................17
dwg12656 ..................61
dwg12659 ..................69
dwg12660 ..................21
dwg12661 ..................23
dwg12691 ..................9
dwg12700 ..................49
dwg12735 ..................75
dwg12829 ..................29
dwg12830 ..................33
dwg12887 ..................19
dwg13562 ..................91
dwg13629 ..................65
dwg13785 ..................13
dwg14474 ..................7
dwg15934 ..................85
dwg16506 ..................77
dwg16511 ..................31
dwg16522 ..................35
dwg16523 ..................41
dwg16524 ..................43
dwg16525 ..................45
dwg16526 ..................57
822-030C ...................15
822-045C ...................67
822-050C ...................67
822-080C ...................15
102
AFM4011 And AFM40133 All-Flex Mower 315-470P
04/02/08
Download from Www.Somanuals.com. All Manuals Search And Download.
This Page Intentionally Left Blank
04/02/08
AFM4011 And AFM40133 All-Flex Mower 315-470P
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Great Plains Manufacturing, Inc.
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|