Husqvarna Lawn Mower 2748 GLS User Manual
2008-01  
Operator's  
Manual  
O0802013  
Ride Mower  
2748 GLS  
96043004600  
03002  
Operator's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY RULES  
Safe Operation Practices for Ride-On Mowers  
GENERAL SERVICE  
III. CHILDREN  
•
•
Never operate machine in a closed area.  
Keep all nuts and bolts tight to be sure the equipment  
is in safe working condition.  
Never tamper with safety devices. Check their proper  
operation regularly.  
Keep machine free of grass, leaves, or other debris  
build-up. Clean oil or fuel spillage and remove any  
fuel-soaked debris. Allow machine to cool before  
storing.  
If you strike a foreign object, stop and inspect the  
machine. Repair, if necessary, before restarting.  
Nevermakeanyadjustmentsorrepairswiththeengine  
running.  
Tragic accidents can occur if the operator is not alert to  
the presence of children. Children are often attracted to  
the machine and the mowing activity. Never assume that  
children will remain where you last saw them.  
•
•
•
•
•
•
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Never allow children to operate the machine.  
Useextracarewhenapproachingblindcorners,shrubs,  
trees, or other objects that may block your view of a  
child.  
•
•
•
Check grass catcher components and the discharge  
guard frequently and replace with manufacturer's rec-  
ommended parts, when necessary.  
•
•
•
•
•
Mower blades are sharp. Wrap the blade or wear  
gloves, and use extra caution when servicing them.  
Check brake operation frequently. Adjust and service  
as required.  
Maintain or replace safety and instruction labels, as  
IV. TOWING  
•
Tow only with a machine that has a hitch designed for  
towing. Do not attach towed equipment except at the  
hitch point.  
•
•
•
•
Follow the manufacturer's recommendation for weight  
limits for towed equipment and towing on slopes.  
Never allow children or others in or on towed equip-  
ment.  
On slopes, the weight of the towed equipment may  
cause loss of traction and loss of control.  
Travel slowly and allow extra distance to stop.  
•
Be sure the area is clear of bystanders before operat-  
ing. Stop machine if anyone enters the area.  
Never carry passengers.  
Do not mow in reverse unless absolutely necessary.  
Always look down and behind before and while back-  
ing.  
•
•
V. SERVICE  
SAFE HANDLING OF GASOLINE  
•
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Mow up and down slopes (15° Max), not across.  
Choose a low ground speed so that you will not have  
to stop or shift while on the slope.  
Avoid starting, stopping, or turning on a slope. If the  
tires lose traction, disengage the blades and proceed  
slowly straight down the slope.  
To avoid personal injury or property damage, use extreme  
careinhandlinggasoline. Gasolineisextremelyflammable  
and the vapors are explosive.  
•
Extinguish all cigarettes, cigars, pipes, and other  
sources of ignition.  
•
•
•
•
•
Use only approved gasoline container.  
Never remove gas cap or add fuel with the engine  
running. Allow engine to cool before refueling.  
Never fuel the machine indoors.  
Never store the machine or fuel container where there  
is an open flame, spark, or pilot light such as on a water  
heater or other appliances.  
•
•
•
•
•
•
Never fill containers inside a vehicle or on a truck or  
trailer bed with plastic liner. Always place containers  
on the ground away from your vehicle when filling.  
Remove gas-powered equipment from the truck or  
trailer and refuel it on the ground. If this is not possible,  
then refuel such equipment with a portable container,  
rather than from a gasoline dispenser nozzle.  
Keepthenozzleincontactwiththerimofthefueltankor  
container opening at all times until fueling is complete.  
Do not use a nozzle lock-open device.  
•
•
•
If machine stops while going uphill, disengage blades,  
shift into reverse and back down slowly.  
Do not turn on slopes unless necessary, and then, turn  
slowly and gradually downhill, if possible.  
•
•
•
If fuel is spilled on clothing, change clothing immedi-  
ately.  
Never overfill fuel tank. Replace gas cap and tighten  
securely.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT SPECIFICATIONS  
CUSTOMER RESPONSIBILITIES  
Gasoline Capacity  
and type:  
4 Gallons  
•
•
Read and observe the safety rules.  
Unleaded Regular  
Follow a regular schedule in maintaining, caring for  
and using your tractor.  
Oil Type (API-SG-SL):  
SAE 30 (above 32°F)  
SAE 5W-30 (below 32°F)  
•
Follow the instructions under “Maintenance” and “Stor-  
age” sections of this owner’s manual.  
Oil Capacity:  
w/Filter: 64 oz  
w/o Filter: 60 oz  
Spark Plug:  
Champion QC12YC  
(Gap: .040")  
WARNING: This tractor is equipped with an internal com-  
bustion engine and should not be used on or near any un-  
improved forest-covered, brush-covered or grass-covered  
land unless the engine’s exhaust system is equipped with  
a spark arrester meeting applicable local or state laws (if  
any). If a spark arrester is used, it should be maintained  
in effective working order by the operator.  
Ground Speed (MPH):  
Forward:  
Reverse:  
0 – 5.5  
0 – 2.4  
Charging System:  
Battery:  
16 AMPS  
AMP/HR:  
MIN. CCA:  
Case Size:  
28  
230  
U1R  
In the state of California the above is required by law  
(Section 4442 of the California Public Resources Code).  
Other states may have similar laws. Federal laws apply  
on federal lands.  
Blade Bolt Torque:  
45-55 FT. LBS.  
CONGRATULATIONS on your purchase of a new tractor.  
Ithasbeendesigned,engineeredandmanufacturedtogive  
you the best possible dependability and performance.  
A spark arrester for the muffler is available through your  
nearestauthorizedservicecenter/department (SeeREPAIR  
PARTS section of this manual).  
Shouldyouexperienceanyproblemyoucannoteasilyrem-  
edy, please contact your nearest authorized servicecenter/  
department We have competent, well-trained technicians  
and the proper tools to service or repair this tractor.  
Please read and retain this manual. The instructions will  
enable you to assemble and maintain your tractor properly.  
Always observe the “SAFETY RULES”.  
TABLE OF CONTENTS  
SAFETY RULES .........................................................2-3  
PRODUCT SPECIFICATIONS....................................... 4  
CUSTOMER RESPONSIBILITIES................................. 4  
ASSEMBLY.................................................................5-6  
OPERATION .............................................................7-13  
MAINTENANCE SCHEDULE ...................................... 14  
MAINTENANCE..................................................... 14-17  
SERVICE AND ADJUSTMENTS............................18-23  
STORAGE.................................................................... 24  
TROUBLESHOOTING............................................25-26  
REPAIR PARTS ......................................................28-43  
WARRANTY................................................................. 44  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
UNASSEMBLED PARTS  
Slope Sheet  
Key  
(1) Oil Drain Tube  
(2) Keys  
ASSEMBLY  
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.  
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use  
the correct tools as necessary to insure proper tightness.  
TOOLS REQUIRED FOR ASSEMBLY  
A socket wrench set will make assembly easier. Standard  
wrench sizes are listed.  
(1) 3/4" wrench  
(1) 9/16" wrench  
Pliers  
Tire pressure gauge  
Utility knife  
L
Whenrightorlefthandismentionedinthismanual,itmeans  
when you are in the operating position (seated behind the  
steering wheel).  
TO REMOVE TRACTOR FROM  
CARTON  
02931  
FIG. 1  
UNPACK CARTON  
•
•
•
Remove all accessible loose parts and parts cartons  
from carton.  
ADJUST SEAT (See Fig. 2)  
Cut along dashed lines on all four panels of carton.  
Remove end panels and lay side panels flat.  
Check for any additional loose parts or cartons and  
remove.  
•
•
Sit in seat.  
Lift up adjustment lever (A) and slide seat until a com-  
fortable position is reached which allows you to press  
clutch/brake pedal all the way down.  
•
Release lever to lock seat in position.  
CHECK BATTERY (See Fig. 1)  
•
Lift hood to raised position.  
NOTE:Ifthisbatteryisputintoserviceaftermonthandyear  
indicated on label (L) (label is located between terminals)  
charge battery for minimum of one hour at 6-10 amps.  
(See "BATTERY" in Maintenance section of this manual  
for charging instructions).  
A
FIG. 2  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
NOTE: You may now roll or drive your tractor off the skid.  
Follow the appropriate instruction below to remove the  
tractor from the skid.  
CHECK FOR PROPER POSITION OF ALL  
BELTS  
See the figures that are shown for replacing motion and  
mower blade drive belts in the Service and Adjustments  
section of this manual. Verify that the belts are routed  
correctly.  
WARNING:Beforestarting,read,understandandfollow  
all instructions in the Operation section of this manual. Be  
sure tractor is in a well-ventilated area. Be sure the area in  
front of tractor is clear of other people and objects.  
CHECK BRAKE SYSTEM  
Afteryoulearnhowtooperateyourtractor,checktoseethat  
the brake is operating properly. See “TO CHECK BRAKE”  
in the Service and Adjustments section of this manual.  
TO ROLL TRACTOR OFF SKID (See Op-  
eration section for location and function of  
controls)  
1. Raise attachment lift lever to its highest position.  
2. Release parking brake by depressing brake pedal.  
✓CHECKLIST  
BEFORE YOU OPERATE YOUR NEW TRACTOR, WE  
WISH TO ASSURE THAT YOU RECEIVE THE BEST  
PERFORMANCE AND SATISFACTION FROM THIS  
QUALITY PRODUCT.  
3. Place freewheel control in disengaged position to dis-  
engage transmission (See “TO TRANSPORT” in the  
Operation section of this manual).  
4. Roll tractor forward off skid.  
PLEASE REVIEW THE FOLLOWING CHECKLIST:  
TO DRIVE TRACTOR OFF SKID (See Op-  
eration section for location and function of  
✓
✓
✓
✓
✓
All assembly instructions have been completed.  
No remaining loose parts in carton.  
Battery is properly prepared and charged.  
Seat is adjusted comfortably and tightened securely.  
All tires are properly inflated. (For shipping purposes,  
the tires were overinflated at the factory).  
controls)  
1. Be sure all the above assembly steps have been com-  
pleted.  
2. Check engine oil level and fill fuel tank with gasoline.  
3. Place freewheel control in "transmission engaged"  
position (see "TO TRANSPORT" in Operation section  
of this manual).  
4. Sit on seat in operating position, depress brake pedal  
and set the parking brake.  
✓
Be sure mower deck is properly leveled side-to-side/  
front-to-rear for best cutting results. (Tires must be  
properly inflated for leveling).  
✓
✓
✓
Check mower and drive belts. Be sure they are routed  
properly around pulleys and inside all belt keepers.  
Check wiring. See that all connections are still secure  
and wires are properly clamped.  
Before driving tractor, be sure freewheel control is in  
“transmission engaged” position (see “TO TRANS-  
PORT” in the Operation section of this manual).  
5. Raise attachment lift lever to its highest position.  
6. Remove key from bag and start the engine (see "TO  
START ENGINE" in the Operation section of this  
manual).Afterenginehasstarted,movethrottlecontrol  
to idle (slow) position.  
7. Release parking brake.  
8. Slowly depress forward drive pedal and drive tractor  
off skid.  
WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY  
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT  
ITEMS:  
9. Apply brake to stop tractor and set parking brake.  
10. Turn ignition key to "STOP" position.  
✓
Engine oil is at proper level.  
✓
Fuel tank is filled with fresh, clean, regular unleaded  
gasoline.  
Continue with the instructions that follow.  
✓
Become familiar with all controls, their location and  
function. Operate them before you start the engine.  
CHECK TIRE PRESSURE  
The tires on your tractor were overinflated at the factory  
for shipping purposes. Correct tire pressure is important  
for best cutting performance.  
✓
✓
Be sure brake system is in safe operating condition.  
Be sure Operator Presence System and Reverse Op-  
eration System (ROS) are working properly (See the  
Operation and Maintenance sections in this manual).  
It is important to purge the transmission before op-  
erating your tractor for the first time. Follow proper  
starting and transmission purging instructions (See  
“TOSTARTENGINE”and“PURGETRANSMISSION”  
in the Operation section of this manual).  
•
Reduce tire pressure to PSI shown on tires.  
✓
CHECK DECK LEVELNESS  
For best cutting results, mower housing should be prop-  
erly leveled. See “TO LEVEL MOWER HOUSING” in the  
Service and Adjustments section of this manual.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.  
FAST  
SLOW  
REVERSE  
HIGH  
LOW  
NEUTRAL  
CHOKE  
IGNITION SWITCH  
MOWER LIFT  
ENGINE START  
MOWER HEIGHT  
ENGINE ON  
PARKING BRAKE  
REVERSE  
OPERATION  
SYSTEM (ROS)  
ENGINE OFF  
CLUTCH/BRAKE  
PEDAL  
LIGHTS ON  
CRUISE CONTROL  
BATTERY  
REVERSE  
FUEL  
FORWARD  
15  
15  
ATTACHMENT  
CLUTCH ENGAGED  
DANGER, KEEP HANDS  
AND FEET AWAY  
ATTACHMENT  
CLUTCH DISENGAGED  
SLOPE HAZARDS  
KEEP AREA CLEAR  
(SEE SAFETY RULES SECTION)  
DANGER indicates a hazard which, if not avoided,  
will result in death or serious injury.  
WARNING indicates a hazard which, if not avoided,  
could result in death or serious injury.  
FREE WHEEL  
(Automatic Models only)  
CAUTION indicates a hazard which, if not avoided,  
might result in minor or moderate injury.  
CAUTION when used without the alert symbol,  
indicates a situation that could result in damage  
to the tractor and/or engine.  
Failure to follow instructions  
could result in serious injury or  
death. The safety alert symbol  
is used to identify safety inform-  
ation about hazards which can  
result in death, serious injury  
and/or property damage.  
HOT SURFACES indicates a hazard which,  
if not avoided, could result in death, serious injury  
and/or property damage.  
FIRE indicates a hazard which, if not avoided,  
could result in death, serious injury and/or  
property damage.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOW YOUR TRACTOR  
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR  
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.  
Save this manual for future reference.  
H
D
E
G
P
B
N
F
J
C
Q
A
M
FIG. 3  
Our tractors conform to the applicable safety standards of the American National Standards Institute.  
(A) ATTACHMENT LIFT LEVER – Used to raise and lower  
(G) REVERSE OPERATION SYSTEM (ROS) "ON" PO-  
SITION – Allows operation of mower or other powered  
attachment while in reverse.  
the mower or other attachments mounted to your tractor.  
(B) CLUTCH/BRAKE PEDAL – Used for declutching and  
braking the tractor and starting the engine.  
(H) LIGHT SWITCH – Turns the headlights on and off.  
(C) PARKING BRAKE – Locks clutch/brake pedal into the  
brake position.  
(J) MOTION CONTROL LEVER - Selects the speed and  
direction of the tractor.  
(D) THROTTLE CONTROL – Used to control engine  
(M) FREEWHEEL CONTROL – Disengages transmission  
for pushing or slowly towing the tractor with the engine  
off.  
speed.  
(E) ATTACHMENT CLUTCH SWITCH – Used to engage  
the mower blades, or other attachments mounted to your  
tractor.  
(N) CHOKE CONTROL – Used when starting a cold  
engine.  
(F) IGNITION SWITCH – Used for starting and stopping  
the engine.  
(P)SERVICEREMINDER/HOURMETER– Indicateswhen  
service is required for the engine and mower.  
(Q) 12-VOLT POWER PORT – Used for 12-volt acces-  
sories.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The operation of any tractor can result in foreign objects thrown into the eyes, which  
can result in severe eye damage. Always wear safety glasses or eye shields while  
operating your tractor or performing any adjustments or repairs. We recommend a  
wide vision safety mask over spectacles or standard safety glasses.  
IMPORTANT: Leaving the ignition switch in any position  
other than "STOP" will cause the battery to discharge and  
go dead.  
HOW TO USE YOUR TRACTOR  
TO SET PARKING BRAKE(See Fig. 4)  
NOTE: Under certain conditions when tractor is standing  
idlewiththeenginerunning, hotengineexhaustgasesmay  
cause “browning” of grass. To eliminate this possibility, al-  
ways stop engine when stopping tractor on grass areas.  
Your tractor is equipped with an operator presence sens-  
ing switch. When engine is running, any attempt by the  
operator to leave the seat without first setting the parking  
brake will shut off the engine.  
•
•
Depress brake pedal (B) all the way down and hold.  
CAUTION: Always stop tractor com-  
pletely, as described above, before  
leaving the operator's position.  
Pull parking brake lever (C) up and hold, release pres-  
sure from brake pedal (B), then release parking brake  
lever. Pedal should remain in brake position. Make  
sure parking brake will hold tractor secure.  
B
D
C
N
F
FIG. 4  
STOPPING  
FIG. 6  
MOWER BLADES -  
TO USE THROTTLE CONTROL - D (See Fig. 6)  
Always operate engine at full speed (fast).  
•
To stop mower blades, push attachment clutch switch in  
to disengaged position (O).  
•
Operating engine at less than full speed (fast) reduces  
engines operating efficiency.  
•
Full speed (fast) offers the best bagging and mower  
performance.  
TO USE CHOKE CONTROL - N (See Fig. 6)  
Usechokecontrolwheneveryouarestartingacoldengine.  
Do not use to start a warm engine.  
(I) ATTACHMENT  
(O) PUSH-IN TO  
•
To engage choke control, pull knob out. Slowly push  
knob in to disengage.  
CLUTCH SWITCH  
“DISENGAGED”  
PULL OUT TO “ENGAGE”  
FIG. 5  
GROUND DRIVE -  
•
To stop ground drive, depress brake pedal all the way  
down.  
ENGINE -  
Move throttle control (D) between half and full speed  
(fast) position.  
•
NOTE: Failure to move throttle control between half and  
full speed (fast) position, before stopping, may cause en-  
gine to “backfire”.  
•
Turn ignition key (F) to “STOP” position and remove  
key. Alwaysremovekeywhenleavingtractortoprevent  
unauthorized use.  
•
Never use choke to stop engine.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO MOVE FORWARD AND BACKWARD  
(See Fig. 7)  
NOTE: Adjust gauge wheels with tractor on a flat level  
surface.  
The direction and speed of movement is controlled by the  
Motion Control Lever (J).  
•
Adjust mower to desired cutting height (See “TO AD-  
JUST MOWER CUTTING HEIGHT” in this section of  
manual).  
•
With mower in desired height of cut position, gauge  
wheels should be assembled so they are slightly off  
the ground. Install gauge wheel in appropriate hole.  
Tighten securely.  
•
Repeat for all, installing gauge wheel in same adjust-  
ment hole.  
J
FIG. 7  
•
Start tractor with motion control lever in neutral (N)  
position.  
•
•
Release parking brake.  
Slowly move motion control lever to desired position.  
FIG.9  
TO OPERATE MOWER  
TO ADJUST MOWER CUTTING HEIGHT  
(See Fig. 8)  
The position of the attachment lift lever (A) determines the  
cutting height.  
Yourtractorisequippedwithanoperatorpresencesensing  
switch. Any attempt by the operator to leave the seat with  
the engine running and the attachment clutch engaged will  
shut off the engine. You must remain fully and centrally  
positioned in the seat to prevent the engine from hesitat-  
ing or cutting off when operating your equipment on rough,  
rolling terrain or hills.  
•
•
Select desired height of cut with attachment lift lever.  
Start mower blades by engaging attachment clutch  
control.  
A
TO STOP MOWER BLADES -  
disengage attachment clutch control.  
CAUTION: Do not operate the mower  
without either the entire grass catcher,  
onmowerssoequipped,orthedeflector  
shield (S) in place.  
FIG. 8  
•
Put attachment lift lever in desired cutting height slot.  
The cutting height range is approximately 1" to 4". The  
heights are measured from the ground to the blade tip with  
the engine not running. These heights are approximate  
and may vary depending upon soil conditions, height of  
grass and types of grass being mowed.  
S
•
Theaveragelawnshouldbecuttoapproximately2-1/2  
inches during the cool season and to over 3 inches  
during hot months. For healthier and better looking  
lawns, mow often and after moderate growth.  
•
For best cutting performance, grass over 6 inches  
in height should be mowed twice. Make the first cut  
relatively high; the second to desired height.  
FIG. 10  
REVERSE OPERATION SYSTEM (ROS)  
TO ADJUST GAUGE WHEELS (See Fig. 9)  
Your tractor is equipped with a Reverse Operation System  
(ROS). Any attempt by the operator to travel in the reverse  
direction with the attachment clutch engaged will shut off  
the engine unless ignition key is placed in the ROS "ON"  
position.  
Gaugewheels areproperlyadjustedwhentheyareslightly  
off the ground when mower is at the desired cutting height  
in operating position. Gauge wheels then keep the deck  
in proper position to help prevent scalping in most terrain  
conditions.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
NOTE: To protect hood from damage when transporting  
WARNING: Backing up with the attachment clutch en-  
gaged while mowing is strongly discouraged. Turning the  
ROS "ON", to allow reverse operation with the attachment  
clutch engaged, should only be done when the operator  
decides it is necessary to reposition the machine with the  
attachment engaged. Do not mow in reverse unless  
absolutely necessary.  
your tractor on a truck or a trailer, be sure hood is closed  
and secured to tractor. Use an appropriate means of tying  
hood to tractor (rope, cord, etc.).  
Transmission Engaged  
USING THE REVERSE OPERATION SYSTEM -  
Only use if you are certain no children or other bystanders  
will enter the mowing area.  
•
•
Depress brake pedal all the way down.  
Withenginerunning,turnignitionkeycounterclockwise  
to ROS "ON" position.  
•
•
Look down and behind before and while backing.  
Slowly depress reverse drive pedal to start move-  
ment.  
When use of the ROS is no longer needed, turn the  
ignition key clockwise to engine "ON" position.  
Transmission Disengaged  
FIG. 11  
•
SERVICE REMINDER/HOUR METER  
ROS "ON" POSITION  
ENGINE "ON" POSITION  
(NORMAL OPERATING)  
Serviceremindershowsthetotalnumberofhourstheengine  
has run and flashes to indicate that the engine or mower  
needs servicing. When service is required, the service  
reminder will flash for two hours. To service engine and  
mower, see the Maintenance section of this manual.  
NOTE: Service reminder runs when the ignition key is in  
any position but "STOP". For accurate reading, be sure  
key remains in the "STOP" position when engine is not  
running.  
TO OPERATE ON HILLS  
TOWING CARTS AND OTHER ATTACHMENTS  
CAUTION: Do not drive up or down  
hills with slopes greater than 15° and  
do not drive across any slope.  
Tow only the attachments that are recommended by and  
complywithspecificationsofthemanufacturerofyourtrac-  
tor. Use common sense when towing. Too heavy of a load,  
while on a slope, is dangerous. Tires can lose traction with  
the ground and cause you to lose control of your tractor.  
•
Choose the slowest speed before starting up or down  
hills.  
•
•
Avoid stopping or changing speed on hills.  
If stopping is absolutely necessary, push brake pedal  
quickly to brake position and engage parking brake.  
BEFORE STARTING THE ENGINE  
CHECK ENGINE OIL LEVEL  
•
•
•
Torestartmovement, slowlyreleaseparkingbrakeand  
brake pedal.  
Slowly depress appropriate drive pedal to slowest set-  
ting.  
The engine in your tractor has been shipped, from the  
factory, already filled with summer weight oil.  
•
•
Check engine oil with tractor on level ground.  
Pull up and remove oil fill cap/dipstick; wipe oil off.  
Reinsertthedipstickintothetubeandpushdownfirmly  
into place. Remove and read oil level. If necessary,  
add oil until “FULL” mark on dipstick is reached. Do  
not overfill.  
Make all turns slowly.  
TO TRANSPORT (See Figs. 3 and 11)  
When pushing or towing your tractor, be sure to disengage  
transmission by placing freewheel control in freewheeling  
position. Free wheel control is located at the rear drawbar  
of tractor.  
•
•
•
•
•
•
For cold weather operation you should change oil for  
easier starting (See “OIL VISCOSITY CHART” in the  
Maintenance section of this manual).  
To change engine oil, see the Maintenance section in  
this manual.  
Raiseattachmentlifttohighestpositionwithattachment  
lift control.  
Pull freewheel control out and down into the slot and  
release so it is held in the disengaged position.  
Do not push or tow tractor at more than two (2)  
MPH.  
To reengage transmission, reverse above procedure.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
COLD WEATHER STARTING ( 50° F and below)  
ADD GASOLINE  
•
Whenenginestarts, allowenginetorunwiththethrottle  
controlinthechokepositionuntiltheenginerunsroughly,  
then move throttle control to fast position. This may re-  
quire an engine warm-up period from several seconds  
to several minutes, depending on the temperature.  
•
Fill fuel tank to bottom of filler neck. Do not overfill. Use  
fresh,clean,regularunleadedgasolinewithaminimumof  
87 octane. (Use of leaded gasoline will increase carbon  
and lead oxide deposits and reduce valve life). Do not  
mix oil with gasoline. Purchase fuel in quantities that can  
be used within 30 days to assure fuel freshness.  
AUTOMATIC TRANSMISSION WARM UP  
•
Beforedrivingtheunitincoldweather, thetransmission  
should be warmed up as follows:  
CAUTION: Wipe off any spilled oil or  
fuel. Do not store, spill or use gasoline  
near an open flame.  
•
•
Be sure the tractor is on level ground.  
Release the parking brake and let the brake slowly  
return to operating position.  
IMPORTANT: WHEN OPERATING IN TEMPERATURES  
BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE  
GASOLINE TO HELP INSURE GOOD COLD WEATHER  
STARTING.  
•
Allowoneminutefortransmissiontowarmup. This  
can be done during the engine warm up period.  
•
The attachments can also be used during the engine  
warm-upperiodafterthetransmissionhasbeenwarmed  
up.  
CAUTION: Alcohol blended fuels (called gasohol  
or using ethanol or methanol) can attract moisture  
which leads to separation and formation of acids  
during storage. Acidic gas can damage the fuel  
systemofanenginewhileinstorage. Toavoidengine  
problems, the fuel system should be emptied before  
storage of 30 days or longer. Drain the gas tank,  
start the engine and let it run until the fuel lines and  
carburetor are empty. Use fresh fuel next season.  
See Storage Instructions for additional information.  
Never use engine or carburetor cleaner products in  
the fuel tank or permanent damage may occur.  
NOTE: If at a high altitude (above 3000 feet) or in cold  
temperatures (below 32 F) the carburetor fuel mixture may  
need to be adjusted for best engine performance. See “TO  
ADJUST CARBURETOR” in the Service and Adjustments  
section of this manual.  
PURGE TRANSMISSION  
CAUTION: Never engage or disengage  
freewheel lever while the engine is  
running.  
TO START ENGINE (See Fig. 3)  
When starting the engine for the first time or if the engine  
has run out of fuel, it will take extra cranking time to move  
fuel from the tank to the engine.  
To ensure proper operation and performance, it is recom-  
mended that the transmission be purged before operating  
tractor for the first time. This procedure will remove any  
trapped air inside the transmission which may have de-  
veloped during shipping of your tractor.  
IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE  
REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD  
BE PURGED AFTER REINSTALLATION BEFORE OPERATING  
THE TRACTOR.  
•
Be sure freewheel control is in the transmission en-  
gaged position.  
•
Sit on seat in operating position, depress brake pedal  
and set parking brake.  
•
•
Move attachment clutch to “DISENGAGED” position.  
Move throttle control to choke position.  
•
Place tractor safely on level surface with engine off and  
parking brake set.  
NOTE: Before starting, read the warm and cold starting  
procedures below.  
•
Disengage transmission by placing freewheel control  
in freewheeling position (See “TO TRANSPORT” in  
this section of manual).  
•
Insertkeyintoignitionandturnkeyclockwiseto“START”  
position and release key as soon as engine starts.  
Do not run starter continuously for more than fifteen  
seconds per minute. If the engine does not start after  
several attempts, move throttle control to fast position,  
wait a few minutes and try again. If engine still does  
not start, move the throttle control back to the choke  
position and retry.  
•
•
Sitting in the tractor seat, start engine. After the engine  
is running, move throttle control to slow position. Dis-  
engage parking brake  
Depress forward drive pedal to full forward position,  
hold for five (5) seconds and release pedal. Depress  
reverse drive pedal to full reverse position, hold for five  
(5) seconds and release pedal. Repeat this procedure  
three (3) times.  
WARM WEATHER STARTING (50° F and above)  
•
When engine starts, move the throttle control to the  
fast position.  
NOTE: During this procedure there will be no movement  
of drive wheels. The air is being removed from hydraulic  
drive system.  
•
The attachments and ground drive can now be used. If  
the engine does not accept the load, restart the engine  
and allow it to warm up for one minute using the choke  
as described above.  
•
•
Shut- off engine and set parking brake.  
Engage transmission by placing freewheel control in  
engaged position (See “TO TRANSPORT” in this sec-  
tion of manual).  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
•
•
Sitting in the tractor seat, start engine. After the engine  
is running, move throttle control to half (1/2) speed.  
Disengage parking brake.  
Drive tractor forward for approximately five feet then  
backwards for five feet. Repeat this driving procedure  
three times.  
Your transmission is now purged and now ready for normal  
operation.  
MOWING TIPS  
•
Mower should be properly leveled for best mowing  
performance. See “TO LEVEL MOWER HOUSING” in  
the Service and Adjustments section of this manual.  
FIG. 12  
•
If grass is extremely tall, it should be mowed twice to  
reduce load and possible fire hazard from dried clip-  
pings. Make first cut relatively high; the second to the  
desired height.  
Do not mow grass when it is wet. Wet grass will plug  
mower and leave undesirable clumps. Allow grass to  
dry before mowing.  
Always operate engine at full throttle when mow-  
ing to assure better mowing performance and proper  
discharge of material. Regulate ground speed by  
selecting a low enough gear to give the mower cutting  
performance as well as the quality of cut desired.  
When operating attachments, select a ground speed  
that will suit the terrain and give best performance of  
the attachment being used.  
•
•
The left hand side of mower should be used for trim-  
ming.  
Drive so that clippings are discharged onto the area  
that has been cut. Have the cut area to the right of the  
machine. This will result in a more even distribution of  
clippings and more uniform cutting.  
•
•
•
When mowing large areas, start by turning to the right  
so that clippings will discharge away from shrubs,  
fences, driveways, etc. After one or two rounds, mow  
in the opposite direction making left hand turns until  
finished (See Fig. 12).  
•
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
BEFORE  
EACH  
USE  
EVERY  
8
HOURS  
EVERY  
25  
HOURS  
EVERY  
50  
HOURS  
EVERY  
100  
HOURS  
EVERY  
SEASON  
BEFORE  
STORAGE  
MAINTENANCE  
SCHEDULE  
Check Brake Operation  
T Check Tire Pressure  
R Check Operator Presence & ROS Systems  
A Check for Loose Fasteners  
Check/Replace Mower Blades  
3
4
C
T
0
Lubrication Chart  
Check Battery Level  
Clean Battery and Terminals  
Check Transaxle Cooling  
Check Mower Levelness  
Check V-Belts  
R
Check Engine Oil Level  
1,2  
Change Engine Oil (with oil filter)  
1,2  
E Change Engine Oil (without oil filter)  
N Clean Air Filter  
2
2
G Clean Air Screen  
Inspect Muffler/Spark Arrester  
I
N
1,  
2
2
Replace Oil Filter (If equipped)  
E Clean Engine Cooling Fins  
Replace Spark Plug  
Replace Air Filter Paper Cartridge  
Replace Fuel Filter  
2
1 - Change more often when operating under a heavy load or  
in high ambient temperatures.  
3 - Replace blades more often when mowing in sandy soil.  
4 - Not required if equipped with maintenance-free battery.  
2 - Service more often when operating in dirty or dusty conditions.  
GENERAL RECOMMENDATIONS  
LUBRICATION CHART  
The warranty on this tractor does not cover items that have  
beensubjectedtooperatorabuseornegligence. Toreceive  
full value from the warranty, operator must maintain tractor  
as instructed in this manual.  
➀ Spindle  
➀ Spindle  
Zerk  
Zerk  
➀ Front Wheel  
Some adjustments will need to be made periodically to  
properly maintain your tractor.  
At least once a season, check to see if you should make  
any of the adjustments described in the Service and  
Adjustments section of this manual.  
• At least once a year you should replace the spark  
plug, clean or replace air filter, and check blades and  
belts for wear. A new spark plug and clean air filter  
assure proper air-fuel mixture and help your engine  
run better and last longer.  
Bearing zerk  
➀ Front Wheel  
Bearing zerk  
➁ Engine  
➀ Steering  
Sector Gear  
Teeth  
➀ Mandrel  
Zerks  
02956  
BEFORE EACH USE  
➀ General Purpose Grease  
•
•
•
•
Check engine oil level.  
➁ Refer to Maintenance “ENGINE” Section  
Check brake operation.  
Check tire pressure.  
Check operator presence and  
ROS systems for proper operation.  
Check for loose fasteners.  
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS  
WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS  
LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL  
SHORTENTHELIFEOFTHESELF-LUBRICATINGBEARINGS.  
IFYOUFEELTHEYMUSTBELUBRICATED,USEONLYADRY,  
POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY.  
•
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
BLADE CARE  
For best results mower blades must be sharp. Replace  
worn, bent or damaged blades.  
TRACTOR  
Always observe safety rules when performing any main-  
tenance.  
CAUTION: Use only a replacement  
blade approved by the manufacturer of  
yourtractor.Usingabladenotapproved  
by the manufacturer of your tractor is  
hazardous, could damage your tractor  
and void your warranty.  
BRAKE OPERATION  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be serviced. (See “TO CHECK  
BRAKE” in the Service and Adjustments section of this  
manual).  
BLADE REMOVAL (See Fig. 13)  
TIRES  
•
Raise mower to highest position to allow access to  
blades.  
•
•
•
Maintain proper air pressure in all tires (See PSI on  
tires).  
NOTE: Protect your hands with gloves and/or wrap blade  
with heavy cloth.  
Keep tires free of gasoline, oil, or insect control chemi-  
cals which can harm rubber.  
Avoid stumps, stones, deep ruts, sharp objects and  
other hazards that may cause tire damage.  
•
•
Remove blade bolt by turning counterclockwise.  
Install new blade with stamped "GRASS SIDE" facing  
the ground.  
NOTE: To seal tire punctures and prevent flat tires due  
to slow leaks, tire sealant may be purchased from your  
local parts dealer. Tire sealant also prevents tire dry rot  
and corrosion.  
IMPORTANT: To ensure proper assembly, center hole in  
blade must align with star on mandrel assembly.  
•
Install and tighten blade bolt securely (45-55 Ft. Lbs.  
torque).  
OPERATOR PRESENCE SYSTEM AND REVERSE OP-  
ERATION SYSTEM (ROS)  
IMPORTANT: Special blade bolt is heat treated.  
Mandrel  
Assembly  
Be sure operator presence and reverse operation systems  
are working properly. If your tractor does not function as  
described, repair the problem immediately.  
•
The engine should not start unless the brake pedal is  
fully depressed, and the attachment clutch control is  
in the disengaged position.  
Blade  
CHECK OPERATOR PRESENCE SYSTEM  
Blade Bolt  
(Special)  
•
•
•
Whentheengineisrunning,anyattemptbytheoperator  
to leave the seat without first setting the parking brake  
should shut off the engine.  
When the engine is running and the attachment clutch  
is engaged, any attempt by the operator to leave the  
seat should shut off the engine.  
025  
45  
Star  
Center Hole  
FIG. 13  
The attachment clutch should never operate unless  
the operator is in the seat.  
BATTERY  
Yourtractorhasabatterychargingsystemwhichissufficient  
for normal use. However, periodic charging of the battery  
with an automotive charger will extend its life.  
Engine "ON" Position  
ROS "ON" Position  
(Normal Operating)  
•
•
•
•
Keep battery and terminals clean.  
Keep battery bolts tight.  
Keep small vent holes open.  
Recharge at 6-10 amperes for 1 hour.  
NOTE: The original equipment battery on your tractor is  
maintenance free. Do not attempt to open or remove caps  
or covers. Adding or checking level of electrolyte is not  
necessary.  
CHECK REVERSE OPERATION (ROS) SYSTEM  
•
When the engine is running with the ignition switch in  
the engine "ON" position and the attachment clutch  
engaged, any attempt by the operator to shift into  
reverse should shut off the engine.  
TO CLEAN BATTERY AND TERMINALS  
Corrosion and dirt on the battery and terminals can cause  
the battery to “leak” power.  
•
When the engine is running with the ignition switch in  
the ROS "ON" position and the attachment clutch en-  
gaged, any attempt by the operator to shift into reverse  
should NOT shut off the engine.  
•
•
Remove terminal guard.  
Disconnect BLACK battery cable first then RED bat-  
tery cable and remove battery from tractor.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
•
•
Rinse the battery with plain water and dry.  
Clean terminals and battery cable ends with wire brush  
until bright.  
TO CHANGE ENGINE OIL (See Figs. 14 and 15)  
Determine temperature range expected before oil change.  
All oil must meet API service classification SG-SL.  
•
•
Coat terminals with grease or petroleum jelly.  
•
•
•
•
Be sure tractor is on level surface.  
Oil will drain more freely when warm.  
Catch oil in a suitable container.  
Remove oil fill cap/dipstick. Be careful not to allow dirt  
to enter the engine when changing oil.  
Reinstall battery (See “REPLACING BATTERY" in  
the SERVICE AND ADJUSTMENTS section of this  
manual).  
V-BELTS  
•
•
Remove yellow cap from end of drain valve and install  
the drain tube onto the fitting.  
Unlock drain valve by pushing inward and turning  
counterclockwise.  
Check V-belts for deterioration and wear after 100 hours  
of operation and replace if necessary. The belts are not  
adjustable. Replace belts if they begin to slip from wear.  
TRANSAXLE COOLING  
OIL DRAIN VALVE  
The transmission fan and cooling fins should be kept clean  
to assure proper cooling.  
Do not attempt to clean fan or transmission while engine  
is running or while the transmission is hot. To prevent pos-  
sible damage to seals, do not use high pressure water or  
steam to clean transaxle.  
CLOSED  
AND  
LOCKED  
POSITION  
•
Inspect cooling fan to be sure fan blades are intact and  
clean.  
•
Inspect cooling fins for dirt, grass clippings and other  
materials. To prevent damage to seals, do not use  
compressed air or high pressure sprayer to clean  
cooling fins.  
YELLOW  
CAP  
DRAIN  
TUBE  
TRANSAXLE PUMP FLUID  
The transaxle was sealed at the factory and fluid mainte-  
nance is not required for the life of the transaxle. Should  
the transaxle ever leak or require servicing, contact your  
nearest authorized service center/department.  
FIG. 15  
To open, pull out on the drain valve.  
After oil has drained completely, close and lock the  
drain valve by pushing inward and turning clockwise  
until the pin is in the locked position as shown.  
•
•
ENGINE  
LUBRICATION  
Only use high quality detergent oil rated with API service  
classification SG-SL. Select the oil’s SAE viscosity grade  
according to your expected operating temperature.  
•
•
Remove the drain tube and replace the cap onto to the  
bottom fitting of the drain valve.  
Refill engine with oil through oil fill dipstick tube. Pour  
slowly. Do not overfill. For approximate capacity see  
“PRODUCT SPECIFICATIONS” section of this man-  
ual.  
SAE VISCOSITY GRADES  
•
Use gauge on oil fill cap/dipstick for checking level.  
For accurate reading, insert dipstick into the tube  
and push down firmly into place before removing.  
Keep oil up to, but not over, the “FULL” line on dip-  
stick. Push dipstick down firmly into the tube when  
finished.  
SAE 30  
5W-30  
-20  
0
30  
32 40  
0
100  
60  
80  
F
C
-20  
10  
-30  
-10  
20  
30  
40  
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE  
oil_visc_chart1_e  
FIG. 14  
CLEAN AIR SCREEN  
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)  
improvestartingincoldweather,theywillresultinincreased  
oilconsumptionwhenusedabove32°F. Checkyourengine  
oil level more frequently to avoid possible engine damage  
from running low on oil.  
Air screen must be kept free of dirt and chaff to prevent  
engine damage from overheating. Clean with a wire brush  
or compressed air to remove dirt and stubborn dried gum  
fibers.  
AIR FILTER  
Your engine will not run properly using a dirty air filter.  
Service air cleaner more often under dusty conditions.  
See Engine Manual.  
Change the oil after every 50 hours of operation or at least  
once a year if the tractor is not used for 50 hours in one  
year.  
Check the crankcase oil level before starting the engine  
and after each eight (8) hours of operation. Tighten oil fill  
cap/dipstick securely each time you check the oil level.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
ENGINE OIL FILTER  
2. Make sure the PTO (Blade Engage) is not engaged,  
set the parking brake, and stop the engine.  
3. Threadthenozzleadapter(packagedwithyourtractor’s  
Operator’s Manual) onto the end of your garden hose.  
Replace the engine oil filter every season or every other  
oil change if the tractor is used more than 100 hours in  
one year.  
MUFFLER  
Inspect and replace corroded muffler and spark arrester  
(if equipped) as it could create a fire hazard and/or dam-  
age.  
Hose  
Nozzle Adapter  
Washout Port  
SPARK PLUGS  
Replace spark plugs at the beginning of each mowing  
season or after every 100 hours of operation, whichever  
occurs first. Spark plug type and gap setting are shown in  
“PRODUCT SPECIFICATIONS” section of this manual.  
IN-LINE FUEL FILTER (See Fig. 16A)  
The fuel filter should be replaced once each season. If fuel  
filter becomes clogged, obstructing fuel flow to carburetor,  
replacement is required.  
•
•
•
•
With engine cool, remove filter and plug fuel line sec-  
tions.  
Place new fuel filter in position in fuel line with arrow  
pointing towards carburetor.  
Be sure there are no fuel line leaks and clamps are  
properly positioned.  
Immediately wipe up any spilled gasoline.  
FIG. 16B  
4. Pull back the lock collar of the nozzle adapter and push  
the adapter onto the deck washout port at the left end  
of the mower deck. Release the lock collar to lock the  
adapter on the nozzle.  
CLAMP  
IMPORTANT: Tug hose ensuring connection is secure.  
CLAMP  
5. Turn the water on.  
6. While sitting in the operator’s position on the tractor,  
re-start the engine and place the throttle lever in the  
Fast " " position.  
FUEL FILTER  
FIG. 16A  
IMPORTANT: Recheck the area making certain the area  
is clear.  
CLEANING  
7. Move the tractor’s PTO (Blade Engage) to the ON  
position. Remain in the operator’s position with the  
cutting deck engaged until the deck is cleaned.  
8. Move the tractor’s PTO (Blade Engage) to the OFF  
position. Turn the ignition key to the STOP position to  
turn the tractor’s engine off. Turn the water off.  
•
•
•
Clean engine, battery, seat, finish, etc. of all foreign  
matter.  
Keep finished surfaces and wheels free of all gasoline,  
oil, etc.  
Protect painted surfaces with automotive type wax.  
We do not recommend using a garden hose or pressure  
washer to clean your tractor unless the engine and trans-  
mission are covered to keep water out. Water in engine or  
transmission will shorten the useful life of your tractor. Use  
compressed air or a leaf blower to remove grass, leaves  
and trash from tractor and mower.  
9. Pull back the lock collar of the nozzle adapter to dis-  
connect the adapter from the nozzle washout port.  
10. Move the tractor to a dry area, preferably a concrete or  
paved area. Engage the mower deck PTO to remove  
excess water and to help dry before putting the tractor  
away.  
DECK WASHOUT PORT (See Fig. 16B)  
Your tractor’s deck is equipped with a washout port on  
its surface as part of its deck wash system. It should be  
utilized after each use.  
1. Drive the tractor to a level, clear spot on your lawn,  
near enough to a water spigot for your garden hose to  
reach.  
WARNING: A broken or missing washout  
fitting could expose you or others to  
thrownobjectsfromcontactwiththeblade.  
Replace broken or missing washout fit-  
ting immediately, prior to using mower  
again.  
•
•
Plug any holes in mower with bolts and  
locknuts.  
IMPORTANT:Makecertainthetractor’sdischargechuteis  
directed AWAY from your house, garage, parked cars, etc.  
Remove bagger chute or mulch cover if attached.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST-  
MENTS:  
•
•
•
•
•
Depress brake pedal fully and set parking brake.  
Place attachment clutch in “DISENGAGED” position.  
Turn ignition key to “STOP” and remove key.  
Make sure the blades and all moving parts have completely stopped.  
Disconnect spark plug wire from spark plug and place wire where it cannot come in contact  
with plug.  
•
From right side of mower, disconnect anti-sway bar (S)  
from right rear mower bracket (D) - remove retainer  
spring and washer and pull mower toward you until the  
bar falls from the hole in bracket.  
Turn tractor steering wheel to the left as far as it will go.  
Slide mower out from under right side of tractor.  
TRACTOR (See Fig. 27)  
TO REMOVE MOWER  
•
•
•
Place attachment clutch in “DISENGAGED” position.  
Lower attachment lift lever to its lowest position.  
Disengage belt tension rod (K) from lock bracket (L).  
•
•
TO INSTALL MOWER (See Figs. 17-24)  
Be sure tractor is on level surface and engage parking  
brake.  
CAUTION: Belt tension rod is spring  
loaded. Have a tight grip on rod and  
release slowly.  
•
Lower attachment lift lever to it's lowest position.  
•
•
Remove mower belt from electric clutch pulley (M).  
Disconnect front link (E) from mower - remove retainer  
spring and washer.  
CAUTION: Lift lever is spring loaded.  
Have a tight grip on lift lever, lower it  
slowly and engage in lowest position.  
•
Go to either side of mower and disconnect mower  
suspension arm (A) from chassis and rear lift link (C)  
from rear mower bracket (D) - remove retainer springs  
and washers.  
•
Turn steering wheel to the left as far as it will go and  
position mower on right side of tractor with deflector  
shield to the right.  
•
Go to other side of mower and disconnect the suspen-  
sion arm and rear lift link.  
CAUTION: After rear lift links are dis-  
connected, the attachment lift lever  
will be spring loaded. Have a tight grip  
on lift lever when changing position  
of the lever.  
02965  
B
M
L
F
K
A
E
H
S
C
D
FIG. 17  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
•
ATTACH MOWER SIDE SUSPENSION ARMS (A) TO  
CHASSIS - Position hole in arm over pin (B) on outside  
of tractor chassis and secure with washer and retainer  
spring.  
•
Repeat on opposite side of tractor.  
C
A
D
02965  
NOTE:Besuremowersidesuspensionarms(A)arepointing  
forward before sliding mower under tractor.  
FIG. 21  
•
Slide mower under tractor until it is centered under  
tractor.  
FIRST INSTALL ANTI-SWAY BAR (S).  
- From right side of mower, insert anti-sway bar into  
hole in transmission bracket (T).  
•
ATTACH REAR LIFT LINKS (C) - Lift rear corner of  
mower and position slot in link assembly over pin on  
rear mower bracket (D) and secure with washer and  
retainer spring.  
•
•
•
Repeat on opposite side of tractor.  
Turn steering wheel to position wheels straight for-  
ward.  
S
T
•
ATTACH FRONT LINK (E) - Work from left side of trac-  
tor. Insert rod end of link assembly through front hole  
in tractor front suspension bracket (F) and secure with  
retainer spring (G) through hole in link located behind  
the bracket.  
•
Insertotherendoflink(E)intoholeinfrontmowerbracket  
(H) and secure with washer and retainer spring (J).  
A
E
H
J
02995  
FIG. 18  
- Pivot bar towards you and insert other end of bar  
into hole in rear mower bracket (D). Move mower  
as needed to insert bar.  
F
G
-
Secure with washer and retainer spring as shown  
D
FIG. 22  
•
•
Disengage belt tension rod (K) from locking bracket (L).  
Install belt onto engine clutch pulley (M).  
IMPORTANT: Check belt for proper routing in all mower  
pulley grooves.  
02996  
FIG. 19  
M
A
B
FIG. 20  
FIG. 23  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
•
Engage belt tension rod (K) on locking bracket (L).  
•
•
Raise attachment lift lever to highest position.  
If necessary, adjust gauge wheels before operating  
mower as shown in the Operation section of this  
manual.  
CAUTION: Belt tension rod is spring  
loaded. Have a tight grip on rod and  
engage slowly.  
B
M
L
F
K
A
E
H
S
C
D
FIG. 24  
NOTE: As desired, you can raise the low side of mower  
TO LEVEL MOWER  
or lower the high side.  
Make sure tires are properly inflated to the PSI shown on  
tires. If tires are over or under inflated, it may affect the  
appearance of your lawn and lead you to think the mower  
is not adjusted properly.  
•
•
Go to side of mower you wish to adjust.  
With a 3/4" or adjustable wrench, turn lift link adjust-  
ment nut (A) to the left to lower the mower, or, to the  
right to raise the mower.  
VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 25)  
NOTE: Each full turn of adjustment nut will change mower  
height about 3/16".  
•
With all tires properly inflated and if your lawn appears  
unevenly cut, determine which side of mower is cutting  
lower.  
•
Test your adjustment by mowing some uncut grass  
and visually checking the appearance. Readjust, if  
necessary, until you are satisfied with the results.  
PRECISION SIDE-TO-SIDE ADJUSTMENT  
(See Fig. 26)  
•
With all tires properly inflated, park tractor on level  
ground or driveway.  
A
CAUTION: Blades are sharp. Protect  
your hands with gloves and/or wrap  
blade with heavy cloth.  
•
•
Raise mower to its highest position.  
At both sides of mower, position blade at side and  
measure the distance (A) from bottom edge of blade  
to the ground. The distance should be the same on  
both sides.  
Turn nut left  
to lower mower  
Turn nut right  
to raise mower  
•
If adjustment is necessary, see steps in Visual Adjust-  
ment instructions above.  
02948  
FIG. 25  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
•
Recheck measurements, adjust if necessary until both  
sides are equal.  
NOTE: Each full turn of the adjustment nut will change  
mower height about 1/8".  
•
Recheck measurements, adjust if necessary until front  
tip of blade is 1/8" to 1/2" lower than the rear tip.  
02966  
•
Holdadjustmentnutinpositionwithwrenchandtighten  
jam nut securely against adjustment nut.  
A
A
TO REPLACE MOWER BLADE DRIVE BELT  
(See Fig. 29)  
FIG. 26  
MOWER DRIVE BELT REMOVAL  
FRONT-TO-BACK ADJUSTMENT (See Figs. 27 and 28)  
IMPORTANT: Deck must be level side-to-side.  
•
Park tractor on a level surface. Engage parking  
brake.  
•
•
Lower attachment lift lever to its lowest position.  
Disengage belt tension rod (K) from lock bracket (L).  
To obtain the best cutting results, the mower blades should  
be adjusted so the front tip is 1/8" to 1/2" lower than the  
rear tip when the mower is in its highest position.  
CAUTION: Belt tension rod is spring  
loaded. Have a firm grip on rod and  
release slowly.  
CAUTION:Bladesaresharp.Protectyour  
hands with gloves and/or wrap blade with  
heavy cloth.  
•
•
Remove screws (P) from mandrel covers (Q) and  
remove covers.  
Remove any dirt or grass clippings which may have  
accumulated around mandrels and entire upper deck  
surface.  
•
•
Raise mower to highest position.  
Positionanybladesothetipispointingstraightforward.  
Measure distance (B) to the ground at front and rear  
tip of the blade.  
•
Remove belt from electric clutch pulley (M), both man-  
drel pulleys (R) and all idler pulleys (S).  
•
•
•
If front tip of blade is not 1/8" to 1/2" lower than the  
rear tip, go to the front of tractor.  
With an 11/16" or adjustable wrench, loosen jam nut  
A several turns to clear adjustment nut B.  
With a 3/4" or adjustable wrench, turn front link adjust-  
ment nut (B) clockwise (ltighten) to raise the front of  
mower, or, counterclockwise (loosen) to lower the front  
mower.  
MOWER DRIVE BELT INSTALLATION  
•
Install belt around all mandrel pulleys (R) and around  
idler pulleys (S) as shown.  
Install belt onto electric clutch pulley (M).  
•
IMPORTANT: Check belt for proper routing in all mower  
pulley grooves.  
•
Reassemble mandrel covers (Q). Securely tighten all  
screws.  
02548  
•
Engage belt tension rod (K) on locking bracket (L).  
CAUTION: Belt tension rod is spring  
loaded. Have a tight grip on rod and  
engage slowly.  
B
B
FIG. 27  
•
Raise attachment lift lever to highest position.  
P
P
Q
M
R
B
K
L
Q
A
R
Loosen adjust nut  
B to lower mower  
Tighten adjust nut  
B to raise mower  
S
02950  
R
Loosen jam nut A first  
FIG. 28  
FIG. 29  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
•
Install mower (See “TO INSTALL MOWER” in this  
section of manual).  
TO REPLACE MOTION DRIVE BELT  
(See Fig. 30)  
Park the tractor on level surface. Engage parking brake.  
For assistance, there is a belt installation guide decal on  
bottom side of left footrest.  
TO CHECK BRAKE  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be serviced.  
You may also check brake by:  
•
BELT REMOVAL -  
•
Remove mower (See “TO REMOVE MOWER” in this  
section of manual).  
Park tractor on a level, dry concrete or paved surface,  
depress brake pedal all the way down and engage  
parking brake.  
Disengage transmission by placing freewheel control  
in “transmission disengaged” position. Pull freewheel  
control out and into the slot and release so it is held in  
the disengaged position.  
NOTE: Observe entire motion drive belt and position of all  
belt guides and keepers.  
•
•
•
•
Disconnect clutch wire harness (A).  
Remove anti-rotation link (B) on right side of tractor.  
Remove belt from stationary idler (C) and clutching  
idler (D).  
The rear wheels must lock and skid when you try to manu-  
ally push the tractor forward. If the rear wheels rotate, then  
the brake needs to be serviced. Contact a qualified service  
center.  
•
•
Remove belt from centerspan idler (E).  
Pull belt slack toward rear of tractor. Carefully remove  
belt upwards from transmission input pulley and over  
cooling fan blades (F).  
FRONT WHEEL TOE-IN/CAMBER  
•
•
Removebeltdownwardfromenginepulleyandaround  
Your new tractor front wheel toe-in and camber is set at the  
factory and is normal. The front wheel toe-in and camber  
are not adjustable. If damage has occurred to affect the  
factory set front wheel toe-in or camber, contact a qualified  
service center.  
electric clutch (G).  
Slide belt toward rear of tractor, off the steering plate  
(H) and remove from tractor.  
TO REMOVE WHEEL FOR REPAIRS  
(See Fig. 31)  
•
•
Block up axle securely.  
G
H
Removeaxlecover,retainingringandwasherstoallow  
wheel removal (rear wheel contains a square key - Do  
not lose).  
•
•
Repair tire and reassemble.  
On rear wheels only: align grooves in rear wheel hub  
and axle. Insert square key.  
Replace washers and snap retaining ring securely in  
axle groove.  
Replace axle cover.  
B
A
C
•
J
D
E
•
NOTE: To seal tire punctures and prevent flat tires due to slow  
leaks, tire sealant may be purchased from your local parts  
dealer. Tire sealant also prevents tire dry rot and corrosion.  
F
02953  
WASHERS  
electric  
RETAINING  
RING  
FIG. 30  
AXLE COVER  
BELT INSTALLATION -  
•
•
•
Install new belt from tractor rear to front, over the steer-  
ing plate (H) and above clutch brake pedal shaft (J).  
Pull belt toward front of tractor and roll belt around  
electric clutch and onto engine pulley (G).  
Pullbelttowardrearoftractor. Carefullyworkbeltdown  
around transmission cooling fan and onto the input  
pulley (F). Be sure belt is inside the belt keeper.  
Install belt on centerspan idler (E).  
SQUARE KEY (REAR  
WHEEL ONLY)  
FIG. 31  
TO START ENGINE WITH A WEAK BATTERY  
(See Fig. 32)  
•
•
Install belt through stationary idler (C) and clutching  
idler (D).  
WARNING: Lead-acid batteries gen-  
erate explosive gases. Keep sparks,  
flameandsmokingmaterialsawayfrom  
batteries. Always wear eye protection  
when around batteries.  
•
Reinstall anti-rotation link (B) on right side of tractor.  
Tighten securely.  
Reconnect clutch harness (A).  
Make sure belt is in all pulley grooves and inside all  
belt guides and keepers.  
•
•
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
If your battery is too weak to start the engine, it should be  
recharged. (See "BATTERY" in the MAINTENANCE sec-  
tion of this manual).  
•
ConnectBLACKgroundingcabletonegative(-)battery  
terminal with remaining hex bolt and keps nut. Tighten  
securely  
•
Close hood.  
If “jumper cables” are used for emergency starting, follow  
this procedure:  
TO REPLACE HEADLIGHT BULB  
•
•
IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12  
VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12  
VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO  
START OTHER VEHICLES.  
Raise hood.  
Pull bulb holder out of the hole in the backside of the  
grill.  
•
•
Replace bulb in holder and push bulb holder securely  
back into the hole in the backside of the grill.  
Close hood.  
TO ATTACH JUMPER CABLES -  
•
Connect one end of the RED cable to the POSITIVE  
(+) terminal of each battery(A-B), taking care not to  
short against tractor chassis.  
INTERLOCKS AND RELAYS  
Loose or damaged wiring may cause your tractor to run  
poorly, stop running, or prevent it from starting.  
•
•
ConnectoneendoftheBLACKcabletotheNEGATIVE  
(-) terminal (C) of fully charged battery.  
Connect the other end of the BLACK cable (D) to good  
chassis ground, away from fuel tank and battery.  
•
Check wiring. See electrical wiring diagram in the  
Repair Parts section.  
TO REMOVE CABLES, REVERSE ORDER -  
•
BLACK cable first from chassis and then from the fully  
TO REPLACE FUSE  
Replace with 20 amp automotive-type plug-in fuse. The  
fuse holder is located behind the dash.  
charged battery.  
•
RED cable last from both batteries.  
TO REMOVE HOOD AND GRILL ASSEMBLY  
(See Fig. 34)  
•
•
•
Raise hood.  
Unsnap headlight wire connector.  
Standinfrontoftractor. Grasphoodatsides, tilttoward  
engine and lift off of tractor.  
WEAK OR DEAD  
BATTERY  
FULLY CHARGED  
BATTERY  
•
To replace, reverse above procedure.  
FIG. 32  
HOOD  
REPLACING BATTERY (See Fig. 33)  
WARNING: Do not short battery terminals by allowing  
a wrench or any other object to contact both terminals at  
the same time. Before connecting battery, remove metal  
bracelets, wristwatch bands, rings, etc.  
HEADLIGHT  
WIRE  
CONNECTOR  
Positive terminal must be connected first to prevent spark-  
ing from accidental grounding.  
•
•
Lift hood to raised position.  
02778  
Disconnect BLACK battery cable (A) then RED battery  
cable and carefully remove battery from tractor.  
Install new battery with terminals in same position as  
old battery.  
FirstconnectREDbatterycable(B)topositive(+)battery  
terminal with hex bolt and keps nut as shown. Tighten  
securely. Slide terminal cover (C) over terminal.  
•
•
FIG. 34  
ENGINE  
TO ADJUST THROTTLE CONTROL CABLE  
The throttle control has been preset at the factory and  
adjustment should not be necessary. If adjustment is nec-  
essary, see engine manual.  
Negative  
(Black)  
Cable  
A
C
TO ADJUST CHOKE CONTROL  
The choke control has been preset at the factory and ad-  
justment should not be necessary. If adjustment is neces-  
sary, see engne manual.  
B
Positive  
(Red)  
Cable  
TO ADJUST CARBURETOR  
Your carburetor is not adjustable. If your engine does not  
operate properly due to suspected carburetor problems,  
take your tractor to an authorized service center for repair  
and/or adjustment.  
02954  
FIG. 33  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STORAGE  
Immediately prepare your tractor for storage at the end  
of the season or if the tractor will not be used for 30 days  
or more.  
ENGINE  
FUEL SYSTEM  
IMPORTANT: ITISIMPORTANTTOPREVENTGUMDEPOSITS  
FROMFORMINGINESSENTIALFUELSYSTEMPARTSSUCH  
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK  
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT  
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING  
ETHANOLORMETHANOL)CANATTRACTMOISTUREWHICH  
LEADSTOSEPARATIONANDFORMATIONOFACIDSDURING  
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM  
OF AN ENGINE WHILE IN STORAGE.  
WARNING: Neverstorethetractorwith  
gasoline in the tank inside a building  
where fumes may reach an open flame  
orspark. Allowtheenginetocoolbefore  
storing in any enclosure.  
TRACTOR  
•
•
•
Empty the fuel tank by starting the engine and let it run  
until the fuel lines and carburetor are empty.  
Never use engine or carburetor cleaner products in  
the fuel tank or permanent damage may occur.  
Remove mower from tractor for winter storage. When  
mower is to be stored for a period of time, clean it thor-  
oughly, remove all dirt, grease, leaves, etc. Store in a  
clean, dry area.  
Use fresh fuel next season.  
•
Clean entire tractor (See “CLEANING” in the Mainte-  
nance section of this manual).  
NOTE: Fuel stabilizer is an acceptable alternative in mini-  
mizing the formation of fuel gum deposits during storage.  
Add stabilizer to gasoline in fuel tank or storage container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to  
allow the stabilizer to reach the carburetor. Do not empty  
the gas tank and carburetor if using fuel stabilizer.  
•
Inspect and replace belts, if necessary (See belt re-  
placement instructions in the Service and Adjustments  
section of this manual).  
•
•
Lubricate as shown in the Maintenance section of this  
manual.  
Be sure that all nuts, bolts and screws are securely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
ENGINE OIL  
Drain oil (with engine warm) and replace with clean engine  
oil. (See “ENGINE” in the Maintenance section of this  
manual).  
•
Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
BATTERY  
CYLINDER(S)  
•
•
Fully charge the battery for storage.  
•
•
Remove spark plug(s).  
After a period of time in storage, battery may require  
recharging.  
Pour one ounce of oil through spark plug hole(s) into  
cylinder(s).  
•
To help prevent corrosion and power leakage during  
long periods of storage, battery cables should be dis-  
connected and battery cleaned thoroughly (see “TO  
CLEAN BATTERY AND TERMINALS” in the Mainte-  
nance section of this manual).  
After cleaning, leave cables disconnected and place  
cables where they cannot come in contact with battery  
terminals.  
•
•
Turn ignition key to “START” position for a few seconds  
to distribute oil.  
Replace with new spark plug(s).  
OTHER  
•
•
•
•
Do not store gasoline from one season to another.  
Replace your gasoline can if your can starts to rust.  
Rust and/or dirt in your gasoline will cause problems.  
If possible, store your tractor indoors and cover it to  
give protection from dust and dirt.  
Cover your tractor with a suitable protective cover that  
does not retain moisture. Do not use plastic. Plastic  
cannot breathe which allows condensation to form and  
will cause your tractor to rust.  
If battery is removed from tractor for storage, do not  
store battery directly on concrete or damp surfaces.  
•
•
IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE  
AND EXHAUST AREAS ARE STILL WARM.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Will not start  
1. Out of fuel.  
1. Fill fuel tank.  
2. Engine not “CHOKED” properly.  
3. Engine flooded.  
4. Bad spark plug.  
5. Dirty air filter.  
2. See “TO START ENGINE” in Operation section.  
3. Wait several minutes before attempting to start.  
4. Replace spark plug.  
5. Clean/replace air filter.  
6. Dirty fuel filter.  
6. Replace fuel filter.  
7. Water in fuel.  
7. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
8. Loose or damaged wiring.  
8. Check all wiring.  
9. Carburetor out of adjustment.  
9. See “To Adjust Carburetor” in Service Adjustments  
section.  
10. Engine valves out of adjustment.  
10. Contact an authorized service center/department.  
Hard to start  
1. Dirty air filter.  
1. Clean/replace air filter.  
2. Bad spark plug.  
2. Replace spark plug.  
3. Weak or dead battery.  
4. Dirty fuel filter.  
3. Recharge or replace battery.  
4. Replace fuel filter.  
5. Stale or dirty fuel.  
6. Loose or damaged wiring.  
7. Carburetor out of adjustment.  
5. Empty fuel tank and refill tank with fresh, clean gasoline.  
6. Check all wiring.  
7. See “To Adjust Carburetor” in Service Adjustments  
section.  
8. Engine valves out of adjustment.  
8. Contact an authorized service center/department.  
Engine will not turn over  
1. Brake pedal not depressed.  
2. Attachment clutch is engaged.  
3. Weak or dead battery.  
1. Depress brake pedal.  
2. Disengage attachment clutch.  
3. Recharge or replace battery.  
4. Replace fuse.  
4. Blown fuse.  
5. Corroded battery terminals.  
6. Loose or damaged wiring.  
7. Faulty ignition switch.  
8. Faulty solenoid or starter.  
9. Faulty operator presence switch(es).  
5. Clean battery terminals.  
6. Check all wiring.  
7. Check/replace ignition switch.  
8. Check/replace solenoid or starter.  
9. Contact an authorized service center/department.  
Engine clicks but will not  
start  
1. Weak or dead battery.  
1. Recharge or replace battery.  
2. Clean battery terminals.  
3. Check all wiring.  
2. Corroded battery terminals.  
3. Loose or damaged wiring.  
4. Faulty solenoid or starter.  
4. Check/replace solenoid or starter.  
Loss of power  
1. Cutting too much grass/too fast.  
2. Throttle in “CHOKE” position.  
3. Build-up of grass, leaves and trash under mower.  
4. Dirty air filter.  
1. Raise cutting height/reduce speed.  
2. Adjust throttle control.  
3. Clean underside of mower housing.  
4. Clean/replace air filter.  
5. Low oil level/dirty oil.  
6. Faulty spark plug.  
7. Dirty fuel filter.  
5. Check oil level/change oil.  
6. Clean and regap or change spark plug.  
7. Replace fuel filter.  
8. Stale or dirty fuel.  
9. Water in fuel.  
8. Empty fuel tank and refill tank with fresh, clean gasoline.  
9. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
10. Spark plug wire loose.  
11. Dirty engine air screen/fins.  
12. Dirty/clogged muffler.  
10. Connect and tighten spark plug wire.  
11. Clean engine air screen/fins.  
12. Clean/replace muffler.  
13. Loose or damaged wiring.  
14. Carburetor out of adjustment.  
13. Check all wiring.  
14. See “To Adjust Carburetor” in Service Adjustments  
section.  
15. Engine valves out of adjustment.  
15. Contact an authorized service center/department.  
Excessive vibration  
1. Worn, bent or loose blade.  
2. Bent blade mandrel.  
1. Replace blade. Tighten blade bolt.  
2. Replace blade mandrel.  
3. Loose/damaged part(s).  
3. Tighten loose part(s). Replace damaged parts.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Engine dies when  
tractor is shifted  
into reverse  
1. Reverse operation system  
(ROS) is not "ON" while  
1. Turn ignition key to  
ROS "ON" position.  
mower or other attachment  
is engaged.  
See Operation section.  
Engine continues to run  
when operator leaves seat  
with attachment clutch  
engaged  
1. Faulty operator-safety presence control system.  
1. Check wiring, switches and connections. If not  
corrected, contact an authorized service center/  
department.  
Poor cut - uneven  
1. Worn, bent or loose blade.  
2. Mower deck not level.  
1. Replace blade. Tighten blade bolt.  
2. Level mower deck.  
3. Buildup of grass, leaves, and trash under mower.  
4. Bent blade mandrel.  
3. Clean underside of mower housing.  
4. Replace blade mandrel.  
5. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
5. Clean around mandrels to open vent holes.  
Mower blades will not  
rotate  
1. Obstruction in clutch mechanism.  
2. Worn/damaged mower drive belt.  
3. Frozen idler pulley.  
1. Remove obstruction.  
2. Replace mower drive belt.  
3. Replace idler pulley.  
4. Frozen blade mandrel.  
4. Replace blade mandrel.  
Poor grass discharge  
1. Engine speed too slow.  
2. Travel speed too fast.  
1. Place throttle control in “FAST” position.  
2. Shift to slower speed.  
3. Wet grass.  
4. Mower deck not level.  
3. Allow grass to dry before mowing.  
4. Level mower deck.  
5. Low/uneven tire air pressure.  
6. Worn, bent or loose blade.  
7. Buildup of grass, leaves and trash under mower.  
8. Mower drive belt worn.  
5. Check tires for proper air pressure.  
6. Replace/sharpen blade. Tighten blade bolt.  
7. Clean underside of mower housing.  
8. Replace mower drive belt.  
9. Blades improperly installed.  
10. Improper blades used.  
11. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
9. Reinstall blades sharp edge down.  
10. Replace with blades listed in this manual.  
11. Clean around mandrels to open vent holes.  
Headlight(s) not working  
(if so equipped)  
1. Light switch is “OFF”.  
2. Bulb(s) or lamp(s) burned out.  
3. Faulty light switch.  
4. Loose or damaged wiring.  
5. Blown fuse.  
1. Turn light switch “ON”.  
2. Replace bulb(s) or lamp(s).  
3. Check/replace light switch.  
4. Check wiring and connections.  
5. Replace fuse.  
Battery will not charge  
1. Bad battery cell(s).  
1. Replace battery.  
2. Poor cable connections.  
3. Faulty regulator (if so equipped).  
4. Faulty alternator.  
2. Check/clean all connections.  
3. Replace regulator.  
4. Replace alternator.  
Loss of drive  
1. Freewheel control in “disengaged” position.  
2. Motion drive belt worn, damaged, or broken.  
3. Air trapped in transmission during shipment  
or servicing.  
1. Place freewheel control in “engaged” position.  
2. Replace motion drive belt.  
3. Purge transmission.  
Engine “backfires” when  
turning engine “OFF”  
1. Engine throttle control not set between half and  
full speed (fast) position before stopping engine.  
1. Move throttle control between half and full speed  
(fast) position before stopping engine.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
SCHEMATIC  
SCH12  
BATTERY  
SOLENOID  
STARTER  
RED  
A
M
RED  
FUSE  
AMMETER  
(OPTIONAL)  
BLACK  
ELECTRIC CLUTCH  
WHITE  
BLACK  
WHITE  
PTO SWITCH  
(DISENGAGED)  
S
H
WHITE  
BLACK  
RED  
M
B
G
C
A
B
A1  
GRAY  
A2  
L
RED  
CLUTCH/BRAKE  
(PEDAL UP)  
D
E
REVERSE SWITCH  
(NOT IN REVERSE)  
BLACK  
BLACK  
BLACK  
2
BLACK  
BLACK  
SEAT SWITCH  
(NOT OCCUPIED)  
BLACK  
BLACK  
3
1
GRAY  
6
JUNCTION  
CONNECTOR  
SHORTING  
CONNECTOR  
CHASSIS  
HARNESS  
H
G
C F  
SPARK  
IGNITION  
UNIT  
PLUGS GAP  
(2 PLUGS ON  
TWIN CYL. ENGINES)  
B
A
E
(OPTIONAL)  
BLUE  
BLACK  
HOUR  
METER  
D
BLACK  
BLUE  
FUEL  
LINE  
12V  
PTO SWITCH  
(MATING SIDE)  
POWER OUTLET  
(OPTIONAL)  
BLUE  
CHARGING SYSTEM OUTPUT  
9 - 1 6 AMP DC @ 3600 RPM  
FUEL SHUT-OFF  
SOLENOID  
(IF EQUIPPED)  
REGULATOR  
RED  
STATOR  
28 VOLTS AC @ 3600 RPM (REGULATOR DISCONNECTED)  
BLACK  
BROWN  
LIGHT  
SWITCH  
HEADLIGHTS  
WIRING INSULATED CLIPS  
NOTE: IF WIRING INSULATED  
CLIPS WERE REMOVED FOR  
SERVICING OF UNIT, THEY  
SHOULD BE RE-INSTALLED TO  
PROPERLY SECURE YOUR  
WIRING.  
3
6
6
5
3
2
IGNITION SWITCH  
NON-REMOVABLE  
CONNECTIONS  
2
1
5
4
POSITION CIRCUIT “MAKE”  
4
1
OFF  
M+G+A1  
B+A1  
RUN/OVERRIDE  
REMOVABLE  
CONNECTIONS  
CHASSIS HARNESS  
CONNECTOR  
DASH HARNESS  
CONNECTOR  
RUN  
B+A1  
L+A2  
START  
B + S + A1  
(MATING SIDE)  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
ELECTRICAL  
T07S  
33  
22  
90  
30  
79  
21  
27  
2
1
24  
91  
99  
100  
34  
8
27  
43  
42  
41  
40  
26  
25  
55  
28  
101  
16  
With 12V Outlet Option  
103  
71  
59  
94  
29  
With Service Minder Option  
92  
46  
93  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
ELECTRICAL  
KEY PART  
NO. NO.  
DESCRIPTION  
1
532 16 34-65 Battery  
874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4  
532 18 64-91 Battery Box  
2
8
16  
21  
22  
24  
25  
26  
27  
28  
29  
30  
33  
34  
40  
41  
42  
43  
46  
50  
55  
59  
71  
79  
90  
91  
92  
93  
94  
99  
532 17 61-38 Switch Interlock  
532 18 37-59 Harness Socket Light  
532 00 41-52 Bulb, Light #1156  
532 40 02-53 Cable Battery  
532 41 28-95 Cable Starter  
532 17 51-58 Fuse  
873 51 04-00 Nut Keps Hex 1/4-20 unc  
532 14 54-91 Cable Ground 21” Blk 6 Ga.  
532 40 15-45 Switch Seat  
532 19 33-50 Switch Ign  
532 41 19-35 Key/Chain  
532 11 07-12 Switch Light/Reset  
532 40 11-04 Harness Ign. Dash  
817 72 04-08 Screw 1/4-20 unc x 1/2  
532 13 15-63 Cover Terminal Red  
532 19 25-07 Solenoid  
532 40 17-63 Gauge Hourmeter  
532 17 46-51 Switch PTO  
817 06 05-12 Screw Thdrol 5/16-18 x 3/4  
532 40 03-03 Outlet 12-Volt  
532 19 42-76 Harness Ign  
532 17 52-42 Socket Asm. Bulb Twistlock  
532 40 07-24 Cover Terminal Battery  
532 19 02-70 Strap Battery  
532 19 66-15 Harness Pigtail Console ROS  
532 19 25-40 Screw Plastite 10-14 x 2.0  
532 19 18-34 Module Reverse ROS  
817 67 04-12 Screw Hexwsh Thdrol 1/4-20 x 3/4  
100 819 09 14-16 Washer 9/32 x 7/8 x 16 Ga.  
101 532 19 83-17 Pigtail MATNLK New Horn  
103 532 40 79-62 Harness Pigtail 12V Outlet  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
CHASSIS  
15  
208  
204  
3
18  
210  
212  
239  
238  
214  
203  
14  
130  
25  
207  
206  
211  
234  
130  
209  
5
176  
137  
202  
234  
176  
205  
176  
175  
177  
150  
178  
161  
196  
176  
221  
195  
176  
162  
199  
36  
37  
182  
130  
236  
194  
36  
235  
181  
34  
68  
194  
218  
213  
130  
180  
213  
165  
68  
68  
162  
189  
183  
68  
217  
228  
194  
152  
181  
58  
228  
189  
52  
189  
chassis-tex_57-gt-husq_r1  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
CHASSIS  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
3
532 40 50-12 Logo Husq.  
195 532 40 35-71 Plug Cruise/Phone  
196 532 41 77-78 Console Asm. Deck Lift  
199 532 19 82-59 Plate Deck Lift  
202 532 40 30-48 Vent Side Hood RH  
203 532 40 30-76 Vent Side Hood LH  
204 532 41 66-13 Vent Asm Hood Top  
205 532 40 17-09 Skirt Hood Side RH  
206 532 40 17-11 Skirt Hood Side LH  
207 532 19 71-98 Bezel RH  
5
532 40 87-01 Dash  
14  
15  
18  
25  
34  
36  
37  
52  
58  
68  
532 41 10-46 Hood  
532 19 89-07 Lens LH  
532 40 86-07 Grille  
532 19 89-06 Lens RH  
532 19 61-25 Plate Engine  
817 06 05-12 Screw 5/16-18 x 3/4  
532 40 18-25 Fender  
873 68 05-00 Nut Crown Lock 5/16-18  
532 19 43-14 Bracket Fender  
817 49 05-08 Screw 5/16-18 x 1/2  
208 532 19 71-99 Bezel LH  
209 532 19 91-30 Insert Hex Top RH  
210 532 19 91-31 Insert Hex Top LH  
211 532 19 91-32 Insert Hex Bottom RH  
212 532 19 91-33 Insert Hex Bottom LH  
213 874 76 05-12 Bolt Hex HD 5/16-18 unc x 3/4  
214 532 19 91-45 Clip Retainer  
130 532 41 63-58 Screw #10 x 0.750 BOS Thread  
137 532 40 75-90 Bumper Dash  
150 532 19 85-12 Duct Heat Hood  
152 532 19 95-35 Shield Browning/Debris  
161 532 40 18-26 Console Fuel Window  
162 532 14 24-32 Screw Hex Wsh Hi-Lo 1/4 x 1/2  
165 532 19 68-26 Bracket Support Tank  
175 532 19 63-04 Crossmember  
176 532 40 07-76 Screw 10-24 x 5/8 Wshd Qdrx  
177 532 19 52-27 Bushing Steering  
178 532 19 97-82 Cargo Asm. Net  
180 532 19 54-77 Chassis  
181 532 40 30-25 Bushing Mtg. Fender Crgo.  
182 532 40 68-59 Dash Lower  
217 532 40 91-67 Rod Pivot  
218 532 19 63-95 Hood Stop  
221 532 19 89-09 Reflector LH  
228 532 19 51-61 Stud Fastener  
234 532 40 47-42 Bumper Hood  
235 532 40 61-29 Spacer Fender  
236 873 93 05-00 Nut Center Lock 5/16-18 unc  
238 532 40 86-06 Trim Husq.  
239 532 11 04-52 Nut Push  
183 874 78 05-20 Bolt Fin Hex 5/16-18 unc x 1-1/4  
189 817 00 05-12 Screw 5/16-18 x 3/4  
194 873 90 05-00 Nut Lock Hex Flange 5/16-18  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
DRIVE  
74  
56  
220  
70  
74  
216  
143  
221  
171  
184  
196  
197  
35  
125  
42  
125  
80  
125  
64  
167  
159  
125  
170  
52  
160  
29  
51  
226  
188  
159  
211  
49  
17  
185  
186  
187  
15  
189  
174  
233  
166  
279  
23  
161  
176  
50  
276  
153  
190  
175  
51  
178  
125  
52  
225  
9
51  
7
22  
183  
166  
116  
2
33  
205  
230  
116  
9
183  
2
7
1
205  
33  
73  
99  
73  
230  
drive-tex_K66_fender_1  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
DRIVE  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
532 41 41-45 Transaxle, TuffTorq K66  
532 00 70-70 Key  
171 872 11 06-16 Bolt  
2
174 532 19 72-89 Nut Push  
7
9
532 19 98-37 Hub Asm. Wheel  
532 14 00-80 Bolt Hub Wheel  
819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.  
532 40 10-72 Spring, Brake  
175 532 40 85-39 Shaft Asm. Shift  
176 532 19 62-14 Arm Clevis Rod Shift  
178 532 19 74-56 Spring Shift  
183 532 19 73-57 Spacer Axle  
184 532 40 31-18 Handle Parking Brake  
185 872 11 06-20 Bolt  
15  
17  
22  
23  
29  
33  
35  
42  
49  
50  
51  
52  
56  
64  
70  
73  
74  
80  
99  
532 19 73-29 Rod Shift  
532 14 08-45 Knob Deluxe 1/2-13 unc  
532 40 72-45 Rod, Brake  
186 532 19 43-21 Spacer Retainer  
187 819 13 32-10 Washer  
812 00 00-53 Ring E  
532 19 95-91 Rod, Brake, Park  
532 12 48-72 Cover, Foot Pedal  
872 11 06-14 Bolt  
188 532 19 43-23 Link Clutch Ground Drive  
189 532 19 43-17 Bellcrank Ground Drive  
190 532 19 43-18 Keeper Bellcrank Ground Drive  
196 817 00 06-16 Screw 3/8-16 x 1  
197 532 19 97-69 Bracket Clutch Anti-Rotation  
205 532 12 38-00 Washer 1 1/32 x 1 5/8 x 16 Ga.  
211 532 19 62-12 Bearing Nylon  
532 19 43-27 Pulley Idler Flat  
873 90 06-00 Lock Nut 3/8-16  
532 19 43-26 Idler V-Groove 910" Offset  
532 12 59-07 V-Belt, Drive  
532 19 62-00 Shaft Asm. Pedal Brake Control  
532 40 02-98 Console Asm.  
216 532 19 61-31 Bracket Pulley Idler  
220 532 19 89-08 Reflector RH  
874 49 05-44 Bolt Hex Flghd 5/16-18 Gr 5  
532 14 24-32 Screw Hx Wsh Hi-Lo 1/4 x 1/2 unc  
532 40 71-82 Strap Torque  
221 532 40 31-87 Retainer Spring Clip Handle  
225 532 40 73-11 Keeper Belt Trans.  
226 532 40 71-09 Bracket Mount Torque  
230 532 00 75-63 Hardened Washer  
233 532 40 52-96 Washer Serrated  
276 874 78 07-16 Bolt Fin Hex 7/16-14 x 1 Gr. 5  
279 532 41 37-78 Link Asm. Shift  
532 41 57-44 Rod Bypass  
116 873 90 05-00 Nut Lock Hex Flange 5/16-18  
125 817 00 05-12 Screw 5/16-18 x 3/4  
143 817 49 05-08 Screw 5/16-18 x 1/2  
153 532 12 47-88 Retainer Spring  
159 876 02 04-12 Pin Cotter 1/8 x 3/4  
160 532 16 94-84 Retainer Clip  
161 532 10 57-09 Spring, Return, Clutch  
166 532 19 72-90 Nut Push .625  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
167 532 40 52-57 Latch Brake Parking  
170 532 19 43-22 Keeper Belt Centerspan  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
STEERING ASSEMBLY  
26  
45  
51  
1
21  
63  
19  
60  
16  
9
7
57  
63  
6
61  
8
66  
67  
2
59  
9
8
7
4
35  
58  
64  
67  
6
28  
15  
70  
14  
5
13  
22  
69  
68  
62  
13  
14  
15  
8
53  
steering-tex_4-husq  
13  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
STEERING ASSEMBLY  
KEY PART  
NO. NO.  
DESCRIPTION  
1
532 41 64-80 Wheel, Steering  
2
532 19 59-68 Axle Asm., Front  
4
532 40 30-89 Spindle Asm., LH  
532 40 30-90 Spindle Asm., RH  
532 12 49-31 Bearing, Race Thrust Harden  
532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.  
812 00 00-29 Ring, Clip #T5304-75  
532 12 12-32 Cap, Spindle  
5
6
7
8
9
13  
14  
15  
16  
19  
21  
22  
26  
28  
35  
45  
51  
53  
57  
58  
59  
60  
61  
62  
63  
64  
66  
67  
68  
69  
70  
532 12 17-49 Washer 25/32 x 1-1/4 x 16 Ga.  
810 04 06-00 Washer, Lock Hvy Hlcl Spr 3/8  
873 54 06-00 Nut, Crown Lock 3/8-24 unf  
532 40 82-19 Shaft Steering  
532 19 47-29 Plate Steering  
532 18 67-37 Adapter, Wheel Steering  
532 19 48-45 Bushing, Strg. Blk  
532 41 59-87 Insert, Wheel Steering  
817 00 06-12 Screw 3/8-16 x 3/4  
532 19 47-32 Gear, Sector Plate  
819 18 38-12 Washer 9/16 x 2-3/8 x 12 Ga.  
873 94 08-00 Nut Hex Jam Toplock 1/2-20 unf  
532 18 89-67 WasherHardened.793x1.637x.060  
532 19 72-46 Bracket Upstop  
532 19 47-47 Bolt Shoulder Sector Pivot CFM  
532 19 47-48 Washer Thrust Sector Steering  
873 97 10-00 Nut Flange Lock 5/8-11  
532 19 47-40 Draglink, LH  
532 19 47-41 Draglink, RH  
817 00 05-12 Screw 5/16-18 x 3/4  
532 19 98-49 Retainer Clip Spring Steering  
871 02 07-48 Bolt Hex Fghd 7/16-14 x 3 Serr  
532 19 47-37 Bushing PM Front Axle  
873 90 07-00 Nut Lock Flange 7/16-14 Gr. 5  
532 19 91-62 Washer 1.5 x .505 x 118  
532 19 61-97 Bracket Deck Susp. Front  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
ENGINE  
1
21  
87  
22  
20  
31  
62  
69  
18  
45  
71  
70  
84  
82  
84  
15  
84  
12  
81  
79  
37  
91  
11  
28  
9
41  
42  
37  
90  
2
85  
29  
SPARK ARRESTER KIT  
engine-tex_bs-2cyl_2  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
ENGINE  
KEY PART  
NO. NO.  
DESCRIPTION  
1
- - - - - -  
Engine B&S Model No. 44Q777-  
1039-B1  
2
9
532 14 97-23 Muffler  
532 19 43-20 Keeper Asm. Belt Engine  
532 17 93-35 Clutch Electric  
11  
12  
15  
18  
20  
21  
22  
28  
29  
31  
37  
41  
42  
45  
62  
69  
70  
71  
79  
81  
82  
84  
85  
87  
90  
91  
532 19 43-43 Pulley Engine  
532 19 34-99 Tank Fuel 4.0  
532 19 42-67 Cap Asm  
532 17 83-85 Control Throttle  
532 41 63-58 Screw #10 x 0.750 BOS Thread  
532 19 15-96 Control Choke  
532 40 11-35 Fuel Line  
532 13 71-80 Spark Arrester Kit  
532 14 50-06 Clip Push-In  
532 12 34-87 Clamp Hose  
532 12 61-97 Washer 1-1/2 OD x 15/32 ID x .250  
810 04 07-00 Washer Lock 7/16  
873 51 04-00 Nut Keps Hex 1/4-20 unc  
532 14 66-29 Shield Heat Muffler  
532 16 53-91 Gasket  
532 15 99-55 Tube Exhaust LH  
532 16 05-89 Tube Exhaust RH  
532 18 39-06 Screw Socket HD 5/16-18 x 1  
532 14 84-56 Tube Drain Oil Easy  
532 18 16-54 Plug Drain Oil Easy  
817 06 06-20 Screw 3/8-16 x 1-1/4  
532 17 99-53 Bolt 7/16-20 x 3.75 Gr. 5  
532 19 82-39 Bolt 5/16-18 unc x 1 w/Sems  
817 00 06-16 Screw 3/8-16 x 1  
532 18 74-95 Bushing  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
For engine service and replacement parts, call the toll free  
number for your engine manufacturer listed below:  
Briggs & Stratton  
1-800-233-3723  
Engine Power Rating Information  
The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive  
Engineers) code J11940 (Small Engine Power & Torque Rating Procedure), and rating performance has been ob-  
tained and corrected in accordance with SAE J1995 (Revision 2002-5). Actual gross engine power will be low-  
er and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both  
the wide array of products on which engines are placed and the variety of environmental issues applicable to op-  
erating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power  
equipment (actual “on-site” or net horsepower). This difference is due to a variety of factors including, but not lim-  
ited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, am-  
bient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufactur-  
ing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
SEAT ASSEMBLY  
1
8
7
8
8
7
8
41  
40  
10  
21  
6
37  
37  
6
2
44  
43  
21  
3
seat-tex_6.5SL_3  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
37  
40  
41  
43  
44  
873 80 05-00 Nut, Lock 5/16-18 unc  
532 19 76-61 Handle Slide Seat  
532 19 82-00 Spring Latch Seat  
874 76 06-12 Bolt Fin Hex 3/8-16 unc x 3/4  
819 13 38-12 Washer 13/32 x 2-3/8 x 12 Ga.  
1
532 40 66-21 Seat  
2
532 18 01-66 Bracket Pivot Fender  
532 14 06-75 Strap, Asm Fender  
873 80 06-00 Nut, Lock w/Ins. 3/8-16 unc  
532 12 41-81 Spring, Seat Cprsn  
532 17 18-77 Bolt 5/16-18 unc x 3/4 w/Sems  
532 19 69-77 Pan, Seat  
3
6
7
8
10  
21  
NOTE: All component dimensions given in U.S. inches  
532 17 18-52 Bolt, Shoulder 5/16-18  
1 inch = 25.4 mm  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
DECALS  
16  
15  
17  
16  
1
14  
14  
3
8
9
6
2
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
16  
17  
- -  
- -  
- -  
- -  
- -  
532 41 57-80 Decal, Hood Logo  
532 41 82-72 Decal, Replacement  
532 16 69-60 Decal, Bypass  
532 40 17-71 Pad, Footrest, LH  
532 40 17-70 Pad, Footrest, RH  
532 41 82-74 Manual, Owner’s (Eng)  
532 41 82-75 Manual, Owner’s (Fr)  
1
532 41 16-58 Decal, Operator’s  
532 41 82-77 Decal, Deck Airinduct  
532 17 05-63 Decal, Warning  
532 41 84-96 Decal, Eng. H.P.  
532 19 87-85 Decal, Mower Sch.  
532 14 50-05 Decal, Battery Dnge/Poi  
532 41 82-15 Decal, Panel Side  
532 18 09-41 Decal, Cust. Resp.  
2
3
6
8
9
14  
15  
KEY  
NO.  
PART  
NO.  
WHEELS AND TIRES  
DESCRIPTION  
1
1
532 05 91-92 Cap, Valve, Tire  
2
532 06 51-39 Stem, Valve  
11  
2
3
3
532 14 45-09 Rim Assembly, Front  
532 00 81-34 Tube, Front (Service Item Only)  
532 10 62-30 Tire, Front  
532 00 02-78 Fitting, Grease (Front Wheel Only)  
532 00 90-40 Bearing, Flange (Front Wheel Only)  
532 17 50-39 Cap, Axle (Front Wheel Only)  
532 10 55-88 Tire, Rear  
4
4
10  
5
7
6
5
7
9
8
6
8
9
10  
11  
12  
- -  
532 00 71-54 Tube, Rear (Service Item Only)  
532 14 45-10 Rim Assembly, Rear  
532 00 68-56 Fitting, Grease  
532 14 43-34 Sealant, Tire (10 oz. Tube)  
NOTE: All component dimensions given in U.S. inches  
wheel_art_1-vgt  
1 inch = 25.4 mm  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
MOWER DECK  
46  
46  
47  
185  
6
39  
49  
21  
122  
48  
46  
114  
43  
50  
7
54  
97  
33  
98  
33  
52  
32  
32  
241  
242  
1
33  
31  
31  
30  
116  
21  
17  
117  
120  
29  
49  
25  
26  
12  
194  
113  
24  
27  
16  
19  
22  
190  
189  
20  
15  
14  
190  
187  
21  
188  
187  
13  
18  
11  
8
48_deck_tex_21  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
MOWER DECK  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
532 41 87-00 Deck Weldment Mower  
532 19 72-48 Cover Mandrel LH  
532 19 91-02 Cover Mandrel RH  
532 17 43-65 Bolt 7/16 Asm. Blade  
532 18 00-54 Blade High Lift  
48  
49  
50  
52  
54  
97  
98  
532 19 31-97 Pulley, Idler Primary  
873 90 06-00 Nut, Lock Flg. 3/8-16 unc  
872 11 06-12 Bolt Carr. 3/8-16 x 1-1/2 Gr. 5  
532 19 73-79 Pulley Idler 4.50 RAW  
817 49 06-36 Screw 3/8-16 x 2-1/4  
532 17 85-15 Washer Hardened  
532 19 61-05 Spring Drive  
6
7
8
11  
- -  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
24  
25  
26  
27  
29  
30  
31  
32  
33  
39  
43  
46  
47  
532 17 39-21 Blade Mulching  
532 40 03-37 Rod Anti Sway  
532 18 72-91 Shaft Asm. w/Lower Bearing  
532 18 72-81 Housing, Mandrel  
532 11 04-85 Bearing, Ball, Mandrel  
819 13 13-12 Washer 13/32 x 13/16 x 12 Ga.  
872 11 05-05 Bolt Carr 5/16-18 x 5/8  
872 14 05-05 Bolt RdHd 5/16-18 unc x 5/8  
532 19 42-08 Pin Cotter 5/16 Bow Tie Lock  
532 17 43-78 Baffle, Vortex  
113 872 11 05-08 Bolt Rdhd Sqnk 5/16-18 x 3/4  
114 532 19 74-51 Rod Tension Relief  
116 532 19 34-06 Bolt, Shoulder  
117 532 17 48-73 Gauge Wheel  
120 819 13 20-12 Washer 13/32 x 1-1/4 x 12 Ga.  
122 532 18 75-57 Bushing Tension Relief  
185 873 90 07-00 Nut Lock Flange 7/16-14 Gr. 5  
187 532 19 51-61 Stud Fastener w/”D” Anti-Rotation  
188 873 90 05-00 Nut Lock Hex Flange  
189 532 19 51-85 Arm Susp. Mower Rear  
190 532 19 65-39 Bolt Shoulder  
194 872 14 07-16 Bolt Carr Sqnk 7/16-24 x 2  
241 532 15 29-27 Screw TT #10-32.5. 3/8 Flange  
242 532 41 55-98 Port Washout  
- -  
- -  
873 68 05-00 Nut, Crownlock 5/16-18 unc  
532 17 44-93 Stripper  
532 10 53-04 Cap Sleeve  
532 17 81-02 Spring, Torsion  
532 11 04-52 Nut, Push  
532 18 17-07 Deflector Shield  
532 13 14-91 Rod, Hinge  
532 18 72-92 Mandrel Assembly (Includes hous-  
ing, shaft assembly, and bearing  
only - pulley/nut/washer and blade  
bolt/washers not included)  
532 41 82-23 Replacement Mower, Complete  
532 17 39-84 Screw, Thdroll Washer Head  
532 18 76-90 Washer, Spacer Mower Vented  
532 15 35-32 Pulley, Mandrel  
532 40 02-34 Nut, Flg. Top Lock  
532 19 73-80 Pulley, Idler, 4.50 HUB  
532 19 60-65 Arm, Idler  
532 13 77-29 Screw, Thdroll. 1/4-20 x 5/8  
532 19 72-42 Belt Deck Drive  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. 2748GLS (96043004600), PRODUCT NO. 960 43 00-46  
MOWER LIFT  
7
87  
87  
90  
98  
89  
3
10  
88  
97  
2
91  
97  
91  
87  
89  
lift-tex_3  
89  
87  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
2
532 19 52-23 Shaft Asm., Lift  
532 19 52-30 Lever Asm., Lift RH  
532 41 15-55 Grip, Lever  
90  
91  
97  
98  
532 19 42-08 Pin Cotter 5/16 Bow Tie Lock  
532 19 79-84 Link Lift Susp Mower Rear  
817 00 06-12 Screw 3/8-16 x .75  
3
7
10  
87  
88  
89  
532 19 63-14 Spring Torsion  
532 19 52-64 Link Lift Susp. Front Mower  
532 19 42-09 Pin Cotter 7/16 Bow Tie Lock  
532 19 53-04 Spring Lift Assist  
819 19 19-12 Washer Clear Zinc  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY STATEMENT  
SECTION 1: LIMITED WARRANTY  
SECTION 4: EXCEPTIONS AND LIMITATIONS  
Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser  
to be free from defects in material and workmanship from the date of purchase for the “Warranty Period” of the  
product as set forth below:  
This warranty shall be inapplicable to defects resulting from the following:  
(1)Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust,  
corrosion, or any adverse reaction due to incorrect storage or use habits;  
(2)Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruc-  
tion sheet furnished by Husqvarna;  
Lifetime Warranty: All tiller tines against breakage, trimmer shafts, ignition coils and modules on hand held  
product.  
(3)Alterations or modifications that change the intended use of the product or affects the product’s per-  
formance, operation, safety, or durability, or causes the product to fail to comply with any applicable  
laws; or:  
3 Year Warranty: Spindles (on Zero Turn Riders and Commercial Walk-Behinds)  
2 Year COMMERCIAL-Warranty: Husqvarna Commercial Turf Equipment—zero turn riders, wide area walks,  
(4)Additional damage to parts or components due to continued use occurring after any of the above.  
and ground engaging commercial equipment.  
2 Year NON-COMMERCIAL Warranty: Automatic Mower, Riding lawn mowers, yard and garden tractors, walk  
behind mowers, tillers, chain saws, trimmers, brushcutters, clearing saws, snow blowers, handheld blowers,  
backpack blowers, hedge trimmers, electrical products and power-assist collection systems for noncommercial,  
nonprofessional, noninstitutional or nonincome producing use, except as herein stated.  
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY  
OF THE PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUEN-  
TIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS  
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MER-  
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN  
DURATION TO THE WARRANTY PERIOD AS DEFINED IN THE LIMITED WARRANTY STATEMENT.  
HUSQVARNA RESERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE PRODUCT  
WITHOUT NOTICE, AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY M A N U FA C -  
TURED PRODUCTS.  
Emission control system components necessary to comply with CARB-TIER-II and EPA regulations, except  
for those components which are part of engine systems manufactured by third party engine manufacturers for  
which the purchaser has received a separate warranty with product information supplied at time of purchase.  
1 Year Warranty: Power cutters, stump grinder, pole pruners and pole saws for non-commercial, non-pro-  
fessional, non-institutional or non-income producing use. All trimmers, brushcutters, clearing saws, hovering  
trimmers, stick edgers, backpack blowers, hand held blowers, hedge trimmers, power-assist collection systems  
used for commercial, institutional, professional or income producing purposes or use.  
Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long  
an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives  
you specific legal rights, and you may also have other rights which vary from state to state.  
Batteries have a one-year prorated limited warranty with 100% replacement during the first 6 months.  
90 Day Warranty: Automatic Mower, Chain saws, power cutters, stump grinders, pole saws, pole pruners,  
snow throwers, model series 580 & 600 walk-behind mowers and commercial turf equipment or any Husqvarna  
product used for commercial, institutional, professional, or income producing purposes or use except as oth-  
erwise provided herein.  
SECTION 5: CUSTOMER RESPONSIBILITIES  
The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as writ-  
ten in the maintenance section of the Owner’s/Operator’s manual. Should an operational problem or failure  
occur, the product should not be used, but delivered as is to an authorized Husqvarna dealer for evaluation.  
Proof of purchase, as explained in section 6, rests solely with the customer.  
Husqvarna Safety Apparel carries a 90-day warranty from the date of the customer’s original purchase for  
defects in material and workmanship. Normal wear, tear or abuse is not covered under warranty. Product must  
be returned to Charlotte with a warranty claim form. All care and maintenance instructions must be followed  
as stated by the manufacturer on the care label. The fit of the protective apparel/boot is not covered under  
warranty.  
SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION  
It is the Owner’s and Dealer’s responsibility to make certain that the Warranty Registration Card is properly  
filled out and mailed to Husqvarna Forest & Garden Company. This card should be mailed within ten (10)  
days from the date of purchase in order to confirm the warranty and to facilitate post-sale service.  
30 Day Warranty: Replacement parts, accessories including bars and chains, tools and display items.  
SECTION 2: HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY  
Proof of purchase must be presented to the authorized Husqvarna dealer in order to obtain warranty ser-  
vice. This proof must include date purchased, model number, serial number, and complete name and address  
of the selling dealer.  
Husqvarna will repair or replace defective components without charge for parts or labor if a component fails  
because of a defect in material or workmanship during the warranty period.  
SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY  
To obtain the benefit of this warranty, the product believed to be defective must be delivered to an au-  
thorized Husqvarna dealer in a timely manner, no later than thirty (30) days from date of the operational  
problem or failure. The product must be delivered at the owner’s expense. Pick-up and delivery charges are  
not covered by this warranty. An authorized Husqvarna dealer can be normally located through the “Yellow  
Pages” of the local telephone directory or by calling 1-800-HUSKY62 for a dealer in your area.  
The following items are not covered by this warranty:  
(1)Normal customer maintenance items which become worn through normal regular use, including, but not  
limited to, belts, blades, blade adapters, bulbs, filters, guide bars, lubricants, rewind springs, saw chain,  
spark plugs, starter ropes and tines;  
(2)Natural discoloration of material due to ultraviolet light;  
(3)Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective  
manufacturer’s warranty as provided in writing with the product information supplied at the time of pur-  
chase; all claims must be sent to the appropriate manufacturer;  
(4)Lawn and garden attachments are covered by a third party which gives a warranty, all claims for war-  
ranty should be sent to the manufacturer; and  
HUSQVARNA  
7349 Statesville Road  
Charlotte, NC 28269  
(5)Emission Control System components necessary to comply with CARB-TIER-II and EPA regulations  
which are manufactured by third party engine manufacturer.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Black Decker Lawn Sweeper NSW18 User Manual
Hayter Mowers Lawn Mower CODE144S User Manual
McCulloch Lawn Mower MC175H42ST User Manual
Snapper Lawn Mower 12LTG36 User Manual
Snapper Lawn Mower 12LTH36 User Manual
Snapper Lawn Mower 1690820 User Manual
Snapper Lawn Mower P215013KWV User Manual
Snapper Lawn Mower ZT18440KH page
Weed Eater Lawn Mower WET2242STA User Manual
Woods Equipment Lawn Aerator PL48 User Manual