Woods Equipment Lawn Mower CZ1736K User Manual
MOW’N MACHINE  
CZ1736K  
872291F  
17HP KAW W/36” SIDE DISCHARGE  
CZ2048K  
872298F  
20HP KAW W/48” SIDE DISCHARGE  
CZ2252K  
872299F  
22HP KAW W/52” SIDE DISCHARGE  
CZ2361B  
872404F  
23HP B&S W/61” SIDE DISCHARGE  
CZ2461K  
872405F  
24HP B&S W/61” SIDE DISCHARGE  
Includes Maintenance Instructions  
RF4164852  
(Rev. 4/14/2010)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WOODS  
IMPORTANT MESSAGE  
TO THE DEALER:  
Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual  
instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in  
the Set-Up instructions are completed before releasing equipment to the owner.  
The dealer must complete the Product Registration online at the Woods Dealer Website or complete the  
mail-in form included with the Operator’s Manual. If using the mail-in form, the dealer is to return the prepaid  
postage portion to Woods, give one copy to the customer, and retain one copy. Failure to register the product  
does not diminish customer’s warranty rights.  
TO THE OWNER:  
Read the Operator’s Manual before operating your Woods equipment. The information presented will prepare  
you to do a better and safer job. Keep the manual handy for ready reference. Require all operators to read  
the Operator’s Manual carefully and become acquainted with all adjustment and operating procedures before  
attempting to operate the equipment. Replacement manuals can be obtained from your dealer. To locate  
your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and  
Canada call 1-800-319-6637.  
The equipment you have purchased has been carefully engineered and manufactured to provide dependable  
and satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as  
specified. Observe all safety information in this manual and safety decals on the equipment.  
For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the  
necessary tools and equipment to handle all your needs.  
Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards  
required for safe and satisfactory operation. Record the model number and serial number of your equipment  
in the spaces provided:  
Model: _______________________________ Date of Purchase: _____________________  
Serial Number: (located on left side panel near cut-off switch.)____________________________  
Provide this information to your dealer to obtain correct repair parts.  
™
ALITEC  
®
BMP  
®
CENTRAL FABRICATORS  
®
GANNON  
®
GILL  
®
WAIN-ROY  
®
WOODS  
12-2009  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
WOODS  
TABLE OF CONTENTS  
FIGURES  
PAGE  
SAFETY.......................................................................................................................................................5-11  
SET-UP INSTRUCTIONS..........................................................................................................................12-13  
LABELS.....................................................................................................................................................14-17  
CONTROLS...............................................................................................................................................18-21  
PRE-OPERATION CHECKLIST.....................................................................................................................22  
OPERATION..............................................................................................................................................23-25  
MAINTENANCE CHART................................................................................................................................26  
MAINTENANCE RECORD.............................................................................................................................27  
MAINTENANCE ........................................................................................................................................28-34  
ADJUSTMENTS........................................................................................................................................35-39  
BELT REPLACEMENT..............................................................................................................................40-41  
NOTES...........................................................................................................................................................42  
PARTS SECTION...........................................................................................................................................43  
FRAME-ENGINE/CLUTCH ASSY....................... FIGURE 1 ...................................................................44, 45  
TRANSAXLE ASSY............................................. FIGURE 2 ...................................................................46, 47  
FUEL TANK/BUMPER & CONTROL PANEL....... FIGURE 3 ...................................................................48, 49  
FUEL VALVE & COVER PLATE.......................... FIGURE 4 ...................................................................50, 51  
DECK LIFT ASSEMBLY ...................................... FIGURE 5 ...................................................................52, 53  
CASTER ASSEMBLY.......................................... FIGURE 6 ...................................................................54, 55  
KICKPLATE/SEAT ASSEMBLY........................... FIGURE 7 ...................................................................56, 57  
STEERING .......................................................... FIGURE 8 ...................................................................58, 59  
PARKING BRAKE ............................................... FIGURE 9 ...................................................................60, 61  
WIRE HARNESS................................................. FIGURE 10 .................................................................62, 63  
36" SIDE DISCHARGE ....................................... FIGURE 11 .................................................................64, 65  
48" SIDE DISCHARGE ....................................... FIGURE 12 .................................................................66, 67  
52" SIDE DISCHARGE ....................................... FIGURE 13 .................................................................68, 69  
61" SIDE DISCHARGE ....................................... FIGURE 14 .................................................................70, 71  
BELTS-CUTTERDECK........................................ FIGURE 15 .................................................................72, 73  
DECALS-POWERUNIT....................................... FIGURE 16 .................................................................74, 75  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY  
WOODS  
This symbol means:  
ATTENTION!  
BECOME ALERT!  
NOTICE !!!  
Unauthorized modifications may present extreme  
safety hazards to operators and bystanders and  
could also result in product damage.  
Your safety and the safety of others is involved.  
Woods stronglywarnsagainst, rejectsanddisclaims  
any modifications, add-on accessories or product  
alterations that are not designed, developed, tested  
and approved by Woods Engineering Department.  
Any Woods product that is altered, modified or  
changed in any manner not specifically authorized  
after original manufacture–including the addition of  
“aftermarket” accessories or component parts not  
specifically approved by Jacobsen–will result in the  
Woods Warranty being voided.  
Signal word definitions:  
The signal words below are used to identify levels  
of hazard seriousness. These words appear in this  
manual and on the safety labels attached to Woods  
machines. For your safety and the safety of others,  
read and follow the information given with these  
signal words and/or the symbol shown above.  
Anyandallliabilityforpersonalinjuryand/orproperty  
damage caused by any unauthorized modifications,  
add-on accessories or products not approved by  
Woods will be considered the responsibility of the  
individual(s) or company designing and/or making  
such changes. Woods will vigorously pursue full  
indemnificationandcostsfromanypartyresponsible  
forsuchunauthorizedpost-manufacturemodifications  
and/or accessories should personal injury and/or  
property damage result.  
DANGER indicates an imminently hazardous  
situation which, if not avoided, WILL result in death  
or serious injury.  
WARNING indicates a potentially hazardous  
situation which, if not avoided, COULD result in  
death or serious injury.  
CAUTIONindicatesapotentiallyhazardoussituation  
which,ifnotavoided,MAY resultinminorormoderate  
injury. It may also be used to alert against unsafe  
practices or property damage.  
CAUTION used without the safety alert symbol  
indicates a potentially hazardous situation which, if  
not avoided, MAY result in property damage  
MODEL NUMBER: This number appears on  
sales literature, technical manuals and price lists.  
SERIAL NUMBER: This number appears only  
on your mower. It contains the model number  
followed consecutively by the serial number.  
Use this number when ordering parts or seeking  
warranty information.  
* Serial Plate located on left side panel near cut-off switch.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY  
WOODS  
PREPARING FOR SAFE OPERATION  
Operator preparation and training  
WARNING  
Read the Operation & Safety  
Manual  
-
If an operator or mechanic  
cannot read English, it is  
the owner's responsibility  
to explain this material to  
them. If any portion of this  
material is unclear, contact  
your factory representative for clarification.  
All rotary lawnmowers are potentially  
dangerous. They canamputatehandsand  
feet and throw objects. Failure to follow  
these safety and operating instructions  
could result in serious injury or death.  
-
Become familiar with the safe operation of the  
equipment, operator controls and safety signs.  
Know how to stop the engine and attachments  
quickly in an emergency. Do not operate or allow  
another person to operate this machine if there  
are any questions about safety.  
-
-
All operators and mechanics should be trained.  
The owner is responsible for training the users.  
Site preparation and circumstances  
-
Evaluate the terrain to determine what  
accessories and attachments are needed to  
properly and safely perform the job. Only use  
accessories and attachments approved by the  
manufacturer.  
Wear appropriate clothing, including long  
trousers and safety goggles or safety glasses  
with side shields when operating mower. Do not  
operate barefoot or wearing open sandals. Long  
hair, loose clothing or jewelry may get tangled in  
moving parts.  
-
-
Clear the area to be mowed of objects such as  
rocks, toys, wire or other debris that may be  
picked up or thrown by the mower.  
-
-
Wear hearing protection.  
Never allow underage children, unskilled  
or improperly trained people operate this  
equipment. Local regulations can restrict the age  
of the operator.  
Be sure the area is clear of pets and people,  
especially young children. Never assume they  
will remain where you last saw them. Stop the  
machine if any enter the area.  
-
Data indicates that those operators age 60 years  
and above are involved in a large percentage of  
riding mower-related injuries. Those operators  
should evaluate their ability to operate the riding  
mower safely enough to protect themselves and  
others from injury.  
-
Mow only in daylight or in good artificial light.  
-
Do not mow wet grass as tires may lose traction.  
-
-
Do not carry passengers, especially small  
children. They may fall off and be seriously  
injured.  
Keep warning labels and this operator's manual  
legible and intact. Replacement labels and  
manuals are available from the factory.  
-
-
Do not operate machine while under the  
influence of drugs or alcohol.  
The owner/user can prevent and is responsible  
for accidents or injuries occurring to themselves,  
other people or property.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY  
WOODS  
OPERATING SAFELY  
Machine preparation  
-
Check operator presence interlock system and  
brake operation. Adjust or repair any problems  
before using.  
In general  
-
Use extra care when loading or unloading the  
machine into a trailer or truck.  
-
Do not tamper with or defeat safety devices.  
Keep guards, shields and interlock safety devices  
in place and in proper working condition. They  
are for your protection.  
-
Slow down and use caution when making turns  
and crossing roads and sidewalks. Stop blades if  
not mowing.  
-
-
-
Do not run the engine in an enclosed area where  
dangerous carbon monoxide fumes can collect.  
-
-
Keep all fasteners such as nuts, bolts and pins  
well secured.  
Do not place your foot on the ground while  
operating the machine.  
Visually inspect blades, blade bolts and the cutter  
assembly for wear or damage. Replace worn or  
damaged blades and bolts to preserve balance.  
Before operating, lower the discharge chute,  
install the mulcher or put the entire grass catcher  
in place.  
-
-
Verify that machine and attachments, if any, are  
in good operating condition.  
-
Keep clear of the discharge opening at all times.  
Never direct the discharge toward a bystander.  
Stop operation if someone approaches.  
Do not engage blades until ready to mow.  
-
-
Keep washout ports and other mower housing  
service openings closed when mowing.  
Use care when pulling loads or using heavy  
equipment.  
- Use only approved drawbar hitch points.  
- Limit loads to those you can safely control.  
- Do not turn sharply. Use care when reversing.  
- Use counterweight(s) or wheel weights when  
suggested in the operator's manual.  
-
Never leave a machine unattended. Always turn  
off blades, set parking brake, stop engine and  
remove key before dismounting.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY  
WOODS  
Starting  
Interrupting operation  
-
Start only according to instructions in this manual  
-
Before leaving the operator's position:  
or on the machine.  
- Park on level ground.  
- Disengage the PTO.  
- Set the parking brake.  
- Shut off the engine and remove the key.  
-
Before attempting to start the engine, make sure:  
- the parking brake is on;  
- the PTO is disengaged;  
- the traction drive is in NEUTRAL.  
-
Disengage the PTO and wait until the blades quit  
rotating:  
- before raising cutterdeck;  
- when not mowing;  
- for transport;  
- when crossing surfaces other than grass.  
-
-
When starting the engine, make sure hands and  
feet are clear of the blades.  
Do not start the machine while standing in front  
of the discharge chute or with the chute directed  
at someone.  
-
Stop the engine, disengage the PTO, set parking  
brake and wait until the blades quit rotating and  
lower cutting unit:  
-
-
Do not engage PTO at full throttle. Throttle to  
idle or lowest possible engine speed.  
Do not change engine governor settings or  
overspeed the engine. Operating the engine  
at excessive speed can increase the hazard of  
personal injury.  
- before refueling;  
- before removing grass catcher;  
- before making height adjustment unless the  
adjustment can be made from the operator's  
position.  
-
Stop the engine, disengage the PTO, set parking  
brake and disconnect the spark plug wire(s) or  
remove the key:  
- before clearing blockages or unclogging chute;  
- before checking, cleaning or working on the  
machine;  
- after striking a foreign object. Inspect the  
machine for damage and make repairs before  
restarting;  
- if the machine begins to vibrate abnormally:  
shut off machine immediately. Inspect and  
make repairs as needed before restarting;  
- except for repairs or adjustments as specifically  
noted, such as for carburetor adjustment,  
where the engine must be running. Keep  
hands and feet clear of moving parts in these  
circumstances.  
-
-
Allow the blades to come to a complete stop  
when stopping operation to clear blockages,  
unclog, inspect the machine, do maintenance or  
repair.  
Reduce the throttle setting during engine shut-  
down and, if the engine is provided with a shut-  
off valve, turn the fuel off at the conclusion of  
mowing.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY  
WOODS  
MANEUVERING SAFELY  
In general  
-
Use extra care with grass catchers or other  
attachments. These can change the stability of  
the machine.  
-
Slow down before turning.  
-
Do not mow in reverse unless absolutely  
necessary. Always look behind and down  
for small children and pets before and during  
backing.  
-
-
Remove obstacles such as rocks, tree limbs etc.  
Avoid driving over obstacles such as ruts, holes,  
rocks and roots whenever possible. Be alert to  
dips and rises. Uneven terrain can overturn a  
mower or cause it to slide. Tall grasses can hide  
obstacles.  
-
-
Be aware when approaching blind corners,  
shrubs, trees, tall grass or other objects that may  
obscure vision.  
If tires lose traction, disengage the blades. If on  
a slope, head downhill.  
-
-
-
Do not mow drop-offs, ditches or embankments.  
The machine could suddenly turn over if a wheel  
runs over the edge or an edge caves in.  
WARNING  
Mowing slopes  
Follow the manufacturer's recommendations  
for wheel weights or counterweights to improve  
stability.  
Slopes are a major factor in  
loss-of-control and tip over  
accidents that sometimes lead  
to severe injury or death. All  
slopes require extra caution.  
Do not mow slopes when grass is wet. Reduced  
traction could cause sliding.  
-
Do not mow on slopes if uneasy or uncertain.  
Ultimate responsibility for safe operation on  
slopes rests with the operator.  
-
-
Do not mow excessively steep slopes.  
On zero turn machines, mow across slopes, not  
up and down.  
-
-
-
Avoid starting or stopping on a slope. If tires  
lose traction, disengage the blades and proceed  
slowly straight down the slope.  
With a zero turn machine, if tires lose traction  
going down a slope, steering control may be  
regained by speeding up.  
Mid-mount zero turns (belly mounted deck) have  
much greater traction pointed up slope than  
down slope. Be aware that traction may be lost  
going down a slope. Do not operate a mid-mount  
zero turn on slopes it cannot back up.  
-
Keep all movement on the slopes slow and  
gradual. Do not make sudden changes in speed  
or direction.  
-
-
-
Do not turn on slopes unless necessary, and then  
turn slowly and downhill when possible.  
Stay away from slopes if the ground is loose or if  
caught in the rain during mowing.  
Use lower speeds on a slope to avoid stopping or  
shifting.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY  
WOODS  
WARNING  
MAINTENANCE SAFETY  
Blades  
-
Mower blades are sharp and  
can cut. Use extra caution  
when handling. Remove ob-  
structions with care. Wrap the  
blade(s) or wear gloves.  
In general  
-
Maintain machine according to manufacturer's  
schedule and instructions for maximum safety  
and best mowing results.  
-
-
Park machine on level ground.  
-
-
-
Be aware that rotating one blade on multi blade  
mowers can cause other blades to rotate.  
Never allow untrained personnel to service ma-  
chine.  
Only replace blades. Never straighten or weld  
them.  
-
-
Adjust or repair only after the engine has been  
stopped and the blades have quit rotating.  
Keep other persons away from blades.  
Inspect grass catcher components regularly. If  
worn, damaged or deteriorated, they may expose  
moving parts or allow objects to be thrown.  
WARNING  
Fuel  
-
-
Replace parts if worn, damaged or faulty.  
For best results, always replace with parts  
recommended by the manufacturer.  
-
Gasoline and diesel fuels are  
flammable; gasoline vapors  
are explosive. Use extra care  
when handling.  
Disconnect battery or remove spark plug wire(s)  
before making any repairs. Disconnect the  
negative terminal first and the positive last. Re-  
connect positive first and negative last.  
-
Store only in containers specifi-  
cally designed for fuel.  
-
When refueling or checking fuel level:  
- Stop the engine and allow to cool;  
- Do not smoke;  
-
Do not dismantle the machine without releasing  
or restraining forces which may cause parts to  
move suddenly.  
- Refuel outdoors only;  
- Use a funnel;  
- Do not overfill;  
- If fuel is spilled, do not attempt to start the  
engine until the spill is cleaned up and vapors  
have cleared.  
-
-
Provide adequate support, e.g. jack stands for  
lifted machine or parts if working beneath.  
Do not put hands or feet near or under rotating  
parts.  
-
-
-
Clean up spilled oil or fuel thoroughly.  
Sparks from static electricity can start fires or cause  
explosions. Flowing fuel can generate static  
electricity. To prevent static electricity sparks:  
Replace faulty mufflers.  
To reduce fire hazards, keep the engine, muffler,  
battery compartment and fuel storage area free  
of grass, leaves, debris buildup or grease.  
-
Keep containers electrically grounded. Do not fill  
containers in a vehicle or on a truck or trailer bed  
with a plastic liner. Fill containers on the ground  
away from the vehicle.  
-
Hydraulic fluid can penetrate skin, use paper  
to check for leaks. Relieve hydraulic pressure  
before disconnecting hoses. Make sure  
connections are tight and hoses are in good  
condition.  
-
When practical, remove gas powered equip-  
ment from the truck or trailer and refuel it on the  
ground. If equipment must be refueled on the  
truck or trailer, refuel from a portable container  
rather than a dispenser nozzle.  
-
-
Keep the dispenser nozzle in contact with the rim  
of the fuel tank or container opening until fueling  
is complete. Do not use a nozzle lock-open  
device.  
Replace caps on fuel cans and tanks securely.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY  
WOODS  
JUMP STARTING  
BATTERY  
WARNING  
Battery acid is caustic and fumes  
are explosive and can cause  
serious injury or death.  
1. Be sure the jumper cables are in good condition.  
Turn off the ignition and all electrical accessories  
on both machines.  
To reduce the risk of personal  
injury when working near a bat-  
tery:  
2. Position the machine with a good (charged) bat-  
tery next to but not touching the machine with the  
dead battery so jumper cables will reach.  
-
When working with battery  
acid, use protective equipment  
such as, but not limited to, goggles, face shield,  
rubber gloves and apron.  
3. When making cable connections:  
- make sure the clamps do not touch anywhere  
except to intended metal parts,  
- Never connect a positive ("+" or red) terminal  
to a negative ("–" or black) terminal.  
-
Avoid leaning over a battery.  
-
Do not expose a battery to open flames or  
- Make sure the cables won't get caught in any  
parts after the engines are started.  
sparks.  
-
Be sure batteries with filler caps are properly  
filled with fluid.  
4. Connect one end of the first jumper cable to the  
positive terminal on one battery. Connect the  
other end to the positive terminal on the other  
battery.  
-
Do not allow battery acid to contact eyes or skin.  
Flush any contacted area with water immediately  
and get medical help.  
5. Connect one end of the other cable to the  
negative terminal of the machine with a good  
(charged) battery. Make the final connection on  
the engine of the machine to be started, away  
from the battery.  
-
Charge batteries in an open, well ventilated area,  
away from sparks and flames. Unplug charger  
before connecting or disconnecting from battery.  
6. Start the vehicle with the good battery, then the  
machine with the discharged battery.  
STORAGE AND TRANSPORTATION  
-
-
-
Stop the engine and allow to cool before storing.  
7. Remove the cables in the exact reverse order of  
installation. When removing each clamp, take  
care it does not touch any other metal parts while  
the other end remains attached.  
Drain the fuel tank outdoors only.  
Store fuel in an approved container in a cool, dry  
place.  
-
-
-
Keep the machine and fuel containers in a locked  
storage place to prevent tampering and to keep  
children from playing with them.  
When the machine is to be parked, stored or left  
unattended, lower the cutterdeck unless a posi-  
tive mechanical lock is used.  
Do not store the machine or fuel container near  
heating appliances with an open flame such as a  
water heater or an appliance with a pilot light.  
-
-
Keep gasoline storage area free of grass, leaves  
and excessive grease to reduce fire hazard.  
Clean grass and debris from cutting units, drives,  
mufflers and engine to help prevent fires.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET-UP INSTRUCTIONS  
WOODS  
TOOLS REqUIRED FOR ASSEMBLY  
-
-
-
-
-
Wrecking bar  
Claw hammer  
Sockets: 1/2”, 15/16  
Wrenches: 18mm, 1/2”, 9/16”, 3/4”, 15/16”  
Tire pressure gauge  
NOTE: All references below to the “right” or “left” are with respect to an operator at the controls.  
1. UNCRATE UNIT  
a) Discard packing materials. Loosen the caster wheel axle bolts and bumper bolts to remove the shipping  
brackets.  
Discard shipping brackets.  
b) Re-install and tighten bumper bolts.  
c) Tighten caster wheel axle bolts against caster axle spanner bushings to 80 ft/lbs.  
2. TIRE PRESSURE  
a) Set tire pressures to 14 lbs/in2 (1.0 kg/cm2). Tires are overinflated for shipping.  
3. TRACTION LEVERS  
a) Tighten bolt A.  
b) Sit on the machine. Levers C may be moved to  
upper set of holes in bar B for a better operator  
fit.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SET UP INSTRUCTIONS  
WOODS  
4. FINAL PREPARATIONS  
-
Check the engine and hydraulic oil levels. Top off with the correct oil if necessary. Use 10W30 motor oil  
for the engine. Use fresh, clean 20W50 motor oil for the hydraulic system. See engine operation manual  
for specified motor oil viscosity.  
-
Charge battery and properly connect cables. See steps below.  
Battery acid is caustic. Fumes are explosive and can cause serious injury or death.  
Use insulated tools, wear protective glasses or goggles and protective clothing when working with batteries.  
Read and obey the battery manufacturer’s instructions.  
Be certain the ignition switch is OFF and the key has been removed before servicing the battery.  
a) Verify battery polarity before connecting or disconnecting the battery cables.  
b) When installing the battery, always assemble the RED, positive ( + ) battery cable first and the  
ground, BLACK, negative ( - ) cable last.  
c) Tighten cables securely to battery terminals and apply a light coat of silicone dielectric grease to  
terminals and cable ends to prevent corrosion. Keep terminal covers in place.  
-
Read Operation and Safety Manual before starting. Operator Manual is located under the seat. Tilt seat  
forward to access manual.  
-
-
If deck does not cut level, see deck leveling procedure in the adjustments section of this manual.  
Run engine at full RPM for 5 minutes before engaging blades to allow the engine to be fully lubricated  
before load is applied.  
-
-
Check the hydro stat neutral adjustment. Neutral is set at the factory but may require readjustment. See  
adjustments section of this manual.  
Do not use the machine without an approved grass collector, the grass discharge chute or mulching  
plates correctly fitted.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LABELS  
WOODS  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LABELS  
WOODS  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LABELS  
WOODS  
DECAL IS LOCATED UNDER FOOTPLATE.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LABELS  
WOODS  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLS  
WOODS  
KEYSWITCH (K) - The keyswitch has three  
positions: OFF, RUN, and START. Insert the key  
and turn it clockwise to move the switch from OFF to  
RUN. Turn it further to START and hold to engage  
the starter. Release the key and the switch will return  
to RUN from START. Turn the key counterclockwise  
to OFF to stop the engine.  
THROTTLE (T) - Move the throttle lever forward to  
increase engine speed until the maximum governed  
engine RPM is reached. Move the lever rearward to  
decrease engine speed until the engine reaches its  
idle speed.  
CHOKE (C)  
For Kawasaki Engines, pull the choke control out to  
set the choke ON. Push it in to set the choke OFF.  
POWER TAKE OFF (PTO) SWITCH (P) -  
The operator must be in the seat when engaging the  
PTO or the engine will kill. Pulling the PTO switch  
out engages (turns on) the PTO and starts the blades  
or other attachment. Pushing the PTO switch in  
disengages (turns off) the PTO and stops the blades  
or other attachment.  
At operator's right side  
NOTE: The PTO switch does not control  
attachments powered by a separate engine.  
-
-
Disengage the PTO whenever you stop or leave  
the operator’s position  
Shut off engine with the key and remove the  
spark plug wires before making adjustments or  
unplugging a clogged mower.  
-
Do not engage the PTO until ready to start  
mowing.  
12 VOLT POWER OUTLET (X) - A 12 volt  
power outlet is provided to operate 12 volt personal  
accessories.  
Below seat  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLS  
WOODS  
FUEL SELECTOR VALVE (U)  
The fuel tank selector valve is located behind the  
seat.  
The fuel tank selector valve has three positions:  
Off: The tank selector is off when the lever points  
down. The selector should be off whenever the  
machine is transported or stands unused for any  
length of time. Shutting off the fuel supply avoids the  
possibility of flooding should any dirt get under the  
carburetor float needle. Leaving the tank selector in  
either tank position can allow severe flooding, which  
may ruin the engine by diluting the oil.  
Right Tank: Fuel flows from the right tank when the  
selector is turned 1/4 turn toward the right.  
Left Tank: Fuel flows from the left tank when the  
selector is turned 1/4 turn toward the left.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLS  
WOODS  
Reverse movement - To move the machine straight  
back, pull both traction levers back equally from their  
neutral position. Reverse speed increases as the  
levers are moved back farther. Maximum reverse  
speed is reached when the levers hit the rear of the  
forward-reverse slot. When moving in reverse, push-  
ing the levers forward slows the machine, and the  
machine stops when the neutral position is reached.  
NOTE: Reverse is spring loaded to return to neutral.  
This spring resistance may be felt when moving the  
traction levers into reverse. When the levers are  
released in reverse, spring tension will slowly return  
them to the neutral position.  
Lift and traction levers  
(operator's right side)  
STEERING - To steer, move one lever forward and  
one back.  
Turns during forward movement:  
LIFT LEVER (F) - Used to raise the cutterdeck to  
maximum height for transport, curb climbing or blade  
changing. To return to preset height of cut, lower lift  
lever until it contacts height of cut pin A.  
-
Right turn - move the right traction lever back  
toward neutral to slow the right drive wheel.  
-
Left turn - move the left traction lever back to-  
ward neutral to slow the left drive wheel.  
TRACTION LEVERS (L) - Each of the two  
traction levers controls the drive wheel located on  
the same side. They control the forward and reverse  
movement of the machine, provide steering and also  
provide dynamic braking.  
Turns during reverse movement:  
-
Reverse right turn - move the right traction lever  
forward toward neutral to slow the right drive  
wheel.  
The operator must be in the seat and the parking  
brake must be OFF to engage the traction drive.  
To engage traction drive, move the traction levers  
toward the center of the machine until they are out of  
neutral lock slot S.  
-
Reverse left turn - move the left traction lever  
forward toward neutral to slow the left drive  
wheel.  
Slow, sweeping turns are made with both traction  
levers on the same side of neutral and slightly  
apart. True zero radius turns about the center of the  
machine are made by having one lever in reverse  
while the other is in forward. By varying the relative  
positions of the two levers, the rate of turn is varied to  
suit the mowing situation.  
Forward movement - To move the machine straight  
ahead, push both traction levers forward equally from  
their neutral position. Forward speed increases as  
the levers are moved farther forward from the neutral  
position. Maximum forward speed is reached when  
the levers hit the front of the forward-reverse slot.  
When traveling forward, pulling the traction levers  
rearward slows the machine. The machine stops  
when the neutral position is reached.  
Slow down before making sharp turns. The machine  
is capable of turning very rapidly when the levers are  
moved further apart from each other. Loss of control  
and/or turf damage may result.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLS  
WOODS  
PARKING BRAKE (R) - Pull the parking brake  
lever up and back to put the parking brake ON. Push  
it forward and down to put the parking brake OFF.  
The parking brake must be ON to start the engine.  
It must also be ON to keep the engine running if the  
operator leaves the seat. The parking brake must be  
OFF to keep the engine running when a traction lever  
is moved out of neutral lock.  
Parking brake in ON position  
(operator's left side)  
PUSHING THE MACHINE  
The machine may be pushed with the engine off, the  
parking brake off, and the bypass valves open.  
To open the bypass valves, move the parking brake  
to the OFF position, then lift and pull bypass control  
rod C through the large opening D, until the control  
rod stop is past the opening. Drop rod C into the  
small opening to lock in place. Repeat for the other  
bypass control rod.  
To close the bypass valves, lift bypass control rod C  
allowing the control rod stop to retract through the  
large opening D.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRE-OPERATION CHECK LIST  
WOODS  
PRE-OPERATION CHECK LIST  
(OPERATOR’S RESPONSIBILITY)  
___ Review and follow all safety rules and safety  
decal instructions.  
___ Never allow riders.  
___ Inspect area and remove stones, branches or  
other hard objects that might be thrown,  
causing injury or damage.  
___ Clean area around oil fill dipstick. Remove  
dipstick and check to be sure oil is in operating  
range (between marks on dipstick). Add oil if  
necessary but Do Not Overfill. Install dipstick  
assembly firmly until cap bottoms out on tube.  
Dipstick assembly must always be secured into  
fill tube when engine is running.  
___ Check all lubrication points and grease as  
instructed in manual.  
___ Check hydrostatic fluid level. Check to be sure  
cooling fins on hydro stat are clean.  
___ Perform a functional check of the safety  
interlock system each time you operate the  
unit.  
___ Check that all safety decals are installed and in  
good condition. Replace if damaged.  
___ Check to make sure all shields and guards  
are properly installed and in good condition.  
Be sure that either the discharge shield or  
complete vacuum attachment is installed.  
___ Check that all hardware is properly installed.  
and secured.  
___ Check that equipment is properly and securely  
attached to power unit.  
___ Check to be sure engine is free of dirt and  
debris. Pay particular attention to the cooling  
fins, governor parts and muffler. Clean air  
intake screen. Check air cleaner; service if  
necessary.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
WOODS  
FUELING  
OPERATOR PRESENCE  
INTERLOCK SYSTEM  
-
Fill fuel tank with good quality, clean, unleaded  
regular gasoline. Do not use hi-test fuel.  
To start the engine:  
-
Use a funnel to avoid spilling.  
-
-
The PTO switch must be OFF.  
Both traction levers must be in the neutral lock  
position.  
-
The parking brake must be ON.  
WARNING  
To operate the machine:  
1. The operator must be in the seat or engaging the  
PTO will kill the engine.  
2. The parking brake must be OFF and the opera-  
tor must be in the seat, or moving a traction lever  
from the neutral lock position will kill the engine.  
TO CHECK OR ADD FUEL:  
– Do it outdoors  
– Do not smoke  
– Stop engine; allow to cool  
– Fill to one inch below bottom  
STARTING THE ENGINE  
of filler neck  
1. Turn the key to operate the electric starter to start  
the engine. Release the key when the engine  
starts.  
– Do not overfill  
– Clean up spilled fuel  
2. If the engine does not start immediately, do not  
crank for more than 10 seconds at a time. Allow  
60 seconds for the starter motor to cool down  
between starting attempts to prevent the starter  
motor from burning out.  
BEFORE STARTING THE ENGINE  
-
-
Be familiar with all controls, how each functions  
and what each operates.  
3. If the choke is ON when the engine starts,  
gradually back it off until the engine runs with no  
choke at all.  
Check the engine oil level and add if necessary.  
Using the fuel selector valve, select which tank  
will supply fuel  
-
Choke: For cold starts, set the throttle lever to the  
half-open position and pull the choke out to the  
ON position. For warm starts set the throttle to  
the half-open position and the choke to the OFF  
position.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
WOODS  
OPERATING NOTES  
DRIVING  
1. With the PTO disengaged, move the parking  
brake to OFF.  
-
-
Practice at slow engine and travel speeds with the  
PTO off until fully familiar with the controls.  
2. Move both traction levers out of neutral lock.  
For normal cutting the throttle should be set at the  
full open position. By using the traction levers to  
speed up or slow down the machine during use,  
maximum control and cutting efficiency can be  
maintained.  
3. Push both traction levers forward evenly to drive  
forward in a straight line. Pull both traction levers  
back evenly to drive backward in a straight line.  
4. Steering - Move one lever forward and one back.  
-
Using the machine at less than full throttle in  
heavy conditions will cause the engine to labor  
and result in excessive wear and can cause dam-  
age to the transaxles.  
Turns during forward movement:  
-
Right turn - move the right traction lever back  
toward neutral to slow the right drive wheel.  
-
Left turn - move the left traction lever back to-  
ward neutral to slow the left drive wheel.  
Turns during reverse movement:  
-
Reverse right turn - move the right traction lever  
forward toward neutral to slow the right drive  
wheel.  
-
Reverse left turn - move the left traction lever  
forward toward neutral to slow the left drive  
wheel.  
Use caution when making turns. Slow down before  
making sharp turns to help maintain control and to  
prevent torn turf from skidding or spinning tires. To  
help prevent turf damage, keep both drive tires mov-  
ing whenever a turn is made.  
TIP: The best way to make a sharp "zero" turn is to  
come to a stop, get the machine moving in reverse  
with both drive wheels and then power the machine  
around with the outside wheel. This technique keeps  
the drive tires turning and results in less turf damage.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
WOODS  
CUTTING  
1. Place the discharge chute in the down position or  
DANGER  
correctly fit a grass collector or mulcher plate.  
2.  
3.  
Sit in the seat.  
Start the engine.  
ROTATING BLADES  
–
–
KEEP HANDS AND FEET AWAY.  
STOP ENGINE AND LET BLADES STOP  
BEFORE REMOVING GRASS COLLEC-  
TOR OR UNCLOGGING.  
4. Turn the blades on by pulling up on the PTO  
switch. Do not start the blades at full throttle.  
Instead, use the slowest throttle setting that will al-  
low the engine to pick up the blade load to reduce  
the wear on the belts and electric clutch.  
5. After the blades are rotating, set the throttle to  
maximum. Use the traction levers to obtain the  
required cutting speed, to steer around obstacles  
and to turn at the end of a cut.  
WARNING  
THROWN OBJECTS  
–
–
–
–
KEEP AREA CLEAR OF PEOPLE  
AND PETS.  
REMOVE OBJECTS BLADE MAY  
STRIKE AND THROW.  
STOP BLADES TO CROSS GRAVEL  
AREAS  
DO NOT OPERATE WITHOUT CHUTE,  
MULCHER OR ENTIRE GRASS  
CATCHER IN PLACE.  
CUTTING TIPS  
-
When mowing large areas, start by turning to the  
right so that clippings will be discharged away  
from shrubs, fences, driveways, etc. After two or  
three rounds, mow in the opposite direction, left  
hand turns, until finished.  
-
If grass is extremely tall, it should be mowed  
twice, the first cut relatively high, the second cut to  
the desired height.  
-
-
Use the left side of the mower for trimming.  
Choose cutting directions so that clippings are  
thrown onto areas that already have been cut.  
This method results in the most even distribution  
of clippings and more uniform, better appearing  
cuts.  
-
Use a different mowing pattern each time where  
possible. This helps prevent rutting and leads  
to a more uniform cut by keeping the grass from  
always laying the same way.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE CHART  
WOODS  
Maintenance is an ongoing job. These intervals are maximum times between  
maintenance operations. Perform more often under severe conditions.  
MAINTENANCE  
OPERATION  
BEFORE  
EACH  
USE  
EVERY  
25  
HOURS  
EVERY  
50  
HOURS  
EVERY  
100  
HOURS  
EVERY  
200  
HOURS  
FIRST 5  
HOURS  
YEARLY  
ENGINE  
Consult the engine manual for additional information and instructions  
Check/Top Up  
X
X
X
Oil Level  
Check For Leaks  
Clean Air Intake  
Screen  
Clean Air Cleaner  
Precleaner  
X
X
Clean Air Cleaner  
Element  
Clean Cooling Fins  
X
Change Oil And  
Filter  
See engine manufacturer's manual  
X
Check/Replace  
Spark Plugs  
X
TRANSAXLE  
Check Oil Level  
X
Check For Leaks  
X
Change Oil And  
Filter  
X
MACHINE  
Check Interlock  
Operation  
X
X
Check Tire  
Pressures  
Check/Top Up  
Battery  
X
ubricate All Points  
L
X
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE RECORD  
WOODS  
NOTES  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
DATE  
HRS  
DATE  
HRS  
DATE  
HRS  
DATE  
HRS  
DATE  
HRS  
DATE  
HRS  
GENERAL  
Check Tire Pressures  
Lubricate All Points  
Check Nuts & Bolts  
ENGINE  
Check Oil Level  
Change Oil  
Clean  
Air Cleaner Element  
Clean Cooling Fins  
Replace  
Air Cleaner Element  
Clean & Gap  
Spark Plugs  
TRANSAXLE  
Change Oil And Filter  
NOTE: After first 5 hours of operation change engine oil and filter.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
WOODS  
CHECK DAILY  
Operator Presence Interlock System - Start Operation  
For the engine to crank, the parking brake must be on, the PTO (blades) off and traction levers in the neutral  
lock position. Sit in the seat and check, one by one, if the engine will crank with the parking brake off, the  
blades on, and either traction lever out of neutral lock.  
Operator Presence Interlock System - Run Operation  
The operator must be in the seat for the engine to run with the parking brake off, the traction levers moved out  
of the neutral lock position, or the blades on. To check:  
1. Start the engine and run at 1/2 throttle with the operator on the machine but raised off the seat.  
2. One by one: move the parking brake to the OFF position, traction levers out of the neutral lock position  
(check each independently), and turn the blades on. Each check should kill the engine after 1/2 second.  
(A 1/2 second delay is built into the system to prevent engine cutout when traversing rough terrain.)  
Repair machine before using if the Operator Presence Interlock System does not operate correctly in start or  
run. Contact your authorized Schiller Grounds Care, Inc. dealer.  
Hardware  
Tighten any nuts and bolts found loose. Replace any broken or missing cotter pins. Repair any other prob-  
lems before operating.  
Tire pressure  
Tires should be kept inflated to 14 lbs/in2 (1.0 kg/cm2). Improper tire inflation can cause rapid tire wear and  
poor traction. Uneven inflation can cause uneven cutting. Overinflation of caster tires can cause casters to  
"wobble" on hard surfaces.  
BATTERY  
4. Check the electrolyte level every 100 hours of  
Battery acid is caustic and fumes  
operation or yearly, whichever comes first. Top  
are explosive and can cause serious injury or death.  
off with distilled water if necessary.  
Use insulated tools, wear protective glasses or  
goggles and protective clothing when working with  
batteries. Read and obey the battery manufacturer’s  
NOTE: Sealed batteries cannot be checked or  
topped off.  
instructions.  
5. Clean the cable ends and battery posts with steel  
wool. Use a solution of baking soda and water  
Be certain the ignition switch is OFF and the key has  
to clean the battery. Do not allow the solution to  
been removed before servicing the battery.  
enter into the battery cells.  
1. Verify battery polarity before connecting or dis-  
6. Tighten cables securely to battery terminals and  
connecting the battery cables.  
apply a light coat of silicone dielectric grease to  
terminals and cable ends to prevent corrosion.  
Keep terminal covers in place.  
2. When installing the battery, always assemble  
the RED, positive ( + ) battery cable first and the  
BLACK ground, negative ( - ) cable last.  
3. When removing the battery, always remove the  
BLACK ground, negative ( - ) cable first and the  
red, positive ( + ) cable last.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
WOODS  
LUBRICATION  
Every 50 hours of operation, lubricate the following points (1-3) with grease:  
1. Deck lift lever (1 point)  
2. Deck lift pivots (4 points)  
3. Pull arms (2 points located at the front of the cutterdeck)  
4. Caster wheel pivots (2 points)  
(Lubricate every 500 hours or once a year)  
NOTE ON BLADE SPINDLES - The blade spindles on these machines use a  
superior sealed bearing that does not require relubrication.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
WOODS  
ENGINE OIL  
Do not perform engine maintenance without the  
engine off, spark plug wires disconnected and PTO  
disengaged.  
AFTER FIRST FIVE (5) HOURS  
While the engine is warm:  
1. Release the oil drain hose assembly from the  
engine clip J. Lay hose assembly over the frame  
edge or through the frame cutout, which ever is  
most convenient.  
2. Remove the rubber cap D from the tip of the  
hose assembly and turn the drain valve to allow  
oil to drain from the engine. Dispose of used oil  
in accordance with local requirements.  
3. Clean drain valve and tighten the plastic portion  
of the drain valve back into the metal portion of  
the valve. Replace rubber cap over the tip of the  
valve. Replace hose assembly back into engine  
clip.  
4. Change oil filter.  
5. Fill the crankcase with fresh oil to the full mark.  
Do not overfill. See engine manual for oil  
specifications.  
DAILY  
1. Check oil level with the dipstick.  
2. If oil is needed, add fresh oil of proper  
viscosity and grade. See engine manual for oil  
specifications. Do not overfill.  
PERIODIC OIL CHANGES  
1. See engine manual for oil and filter change inter-  
vals after the break-in period.  
2. Follow instructions for first oil change, above.  
3. Replace dipstick before starting engine.  
SPARK PLUGS  
Remove each plug and check condition.  
-
-
Good operating conditions are indicated if the plug has a light coating of grey or tan deposit.  
A white blistered coating indicates overheating. A black coating indicates an “over rich” fuel mixture. Both  
may be caused by a clogged air cleaner or improper carburetor adjustment.  
-
Do not sandblast, wire brush or otherwise attempt to repair a plug in poor condition. Best results are  
obtained with a new plug.  
-
Set plug gap as specified in engine manual..  
FUEL FILTER  
An in-line fuel filter is located in the fuel supply line. Inspect at every oil change to make sure it is clean and  
unobstructed. Replace if dirty.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
WOODS  
AIR CLEANER  
Clean and replace the air cleaner element as speci-  
fied in the service chart. Uneven running, lack of  
power or black exhaust may indicate a dirty air  
cleaner.  
1. Unclamp end cover C and remove existing  
cleaner element A.  
2. Insert new element A and replace cover C.  
Ensure breathing port B is pointing down and  
towards the front of the tractor.  
CLEANING MACHINE  
WASHING MACHINE  
Clean the machine after use. The machine will run  
cooler and last longer if kept free of clippings and  
other debris. A clean machine also reduces the risk  
of fire due to accumulation of combustible debris and  
chaff  
CAUTION: Improperly washing a machine can cause  
water to enter bearings and other components. This  
can greatly reduce component life.  
–
Do not use a pressure washer. Do not direct  
water at bearings or seals. High pressure water  
can blow past seals ad enter seal bearings.  
Brush or blow clippings and debris off the cutterdeck  
and engine deck.  
–
–
Allow the machine to cool down before washing.  
Water on a warm machine can be sucked into  
sealed bearings as they cool.  
Avoid getting electrical connections wet. Water  
can cause electrical faults and corrosion of elec-  
trical components.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
WOODS  
ENGINE COOLING  
Continued operation with a clogged cooling system  
will cause severe overheating and can result in en-  
gine damage.  
-
-
Daily: Clean air intake screen V.  
Every 100 hours: Clean cooling fins beneath  
blower housing H with reference to information in  
the engine manufacturer's manual.  
B
)
70 FT-LBS (95 Nm  
LADE BOLTS  
HEEL HUB NUTS  
SPECIFIC TORqUES  
)
150 FT-LBS (203 Nm  
W
E
NGINE CRANKSHAFT BOLT  
50 FT-LBS (68 Nm  
)
TRANSAXLE PULLEY NUT  
TRANSAXLE DRAIN PLUG  
TRANSAXLE FILTER  
28.3 - 41.6 FT-LBS (38 - 56 Nm)  
)
15 - 20 FT-LBS (20 - 27 Nm  
130 - 150 in-lbs (14.6 - 16.9 Nm)  
1. Check the transaxle fluid, fill to proper level, if  
required.  
PURGING TRANSAXLES  
Due to the effects air has on efficiency in hydrostatic  
drive applications, it is critical that it be purged from  
the system.  
2. Raise the drive wheels off the ground. Support  
unit with jack stands or other suitable means.  
3. With the bypass valves open, and the engine  
running, slowly move the control levers in both  
forward and reverse directions 5 to 6 times. As  
air is purged from the unit, the oil level will drop.  
4. With the bypass valve closed, and the engine  
running, slowly move the control levers in both  
forward and reverse directions 5 to 6 times.  
5. Stop engine. Check the transaxle fluid level, add  
fluid as required.  
These purge procedures should be implemented any  
time a hydrostatic system has been opened to fa-  
cilitate maintenance or any additional fluid has been  
added to the system.  
Purging may be required if the unit shows any of the  
following symptoms:  
- Noisy operation.  
- Lack of power or drive after short term use.  
- High operation temperature, excessive oil  
expansion.  
6. It may be necessary to repeat steps 3-5 until all  
the air is completely purged from the system.  
When the transaxle moves forward and reverse  
at normal speed, purging is complete.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
WOODS  
TRANSAXLES  
Inattention to proper safety, operation, or  
maintenance procedures could result in personal  
injury, or damage to the equipment. Schiller  
Grounds Care, Inc. recommends returning the  
machine to your authorized Schiller Grounds  
Care, Inc. dealer for service or repair.  
Perform transaxle maintenance with the engine off,  
spark plug wires disconnected and PTO disengaged.  
TRANSAXLE FLUID CHANGE  
Change the transaxle fluid every 200 hours of  
operation. It is essential that the exterior of the  
transaxle be free of debris, prior to fluid maintenance.  
1. Remove the three 1/4" filter guard screws and  
filter guard A. Remove the oil filter B from the  
transaxle and discard. Dispose of used oil in ac-  
cordance with local requirements.  
2. Wipe the filter base surface off and apply a film  
of new oil to the gasket of the new replacement  
filter. Install the new filter by hand, turn 3/4 to  
one full turn after the filter gasket contacts the  
filter base surface.  
3. Re-install the filter guard and torque the three  
screws to 65 in. lbs. each.  
4. Remove cap C, fill the transaxles through the  
expansion tank D with approximately 2 quarts of  
SAE 20W-50 engine oil PER TRANSAXLE.  
Do not overfill! If you overfill the transaxle while the unit  
is "cold", it may overflow as it reaches normal operating  
temperatures. The oil level should not be above the  
manufacturer's suggestions. This will allow the space  
needed for the oil to expand as it warms up.  
5. After starting engine, check the fluid level and  
continue to add oil to overflow tank D to fill line  
on tank.  
6. Purge the transaxles, following the purging pro-  
cedures on Page 31.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
WOODS  
BLADE REMOVAL  
BLADE BALANCE  
Follow these instructions to prevent injury during  
blade removal:  
1. Loosen with a box wrench or a socket and long  
breaker bar. To gain additional leverage, slip a  
long pipe or thick-walled tube over breaker bar or  
wrench.  
Blade balance must be maintained at 5/8 oz-in (19.4  
g-cm) or less. Failure to keep blades balanced  
causes excess vibration, wear, and shortened life of  
most components of the machine.  
To balance a blade:  
2. Insert wood block A as shown, with grain  
perpendicular to blade, to prevent blade from  
turning when loosening.  
3. Wear thickly padded gloves. Keep hands clear  
of blade path. Blades may rotate when bolt  
releases.  
1. Sharpen blade first.  
2. Balance the blade at the center.  
3. Attach a 1/8 oz (3.9 g) weight at a distance 5"  
(127 mm) from center on the light end. This  
should make the light end the heavy end:  
-
-
If it does, the blade is balanced.  
If does not, file or grind the heavy end until  
the addition of the weight makes the light end  
the heavy end.  
BLADE INSTALLATION  
1. Wear thickly padded gloves to prevent cuts from  
the sharp blade.  
2. Insert the blade bolt, in order, through the conical  
washer (cup side toward the blade, as shown),  
the blade, and the blade spacer.  
3. Install assembly on the blade spindle.  
4. Torque the blade bolt to 70 ft-lbs.  
SHARPENING  
Blades may be sharpened by filing or grinding.  
-
-
-
Inspect blades before sharpening.  
Replace bent or cracked blades.  
Replace blades when the lift portion has worn  
thin.  
-
-
-
Maintain cut angle at 30o.  
Do not overheat blades when sharpening.  
Always use Schiller Grounds Care, Inc.blades.  
Use of another manufacturer’s blades may be  
dangerous.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADJUSTMENTS  
WOODS  
DECK LEVELING  
1. Park the machine on a smooth, level surface.  
Raise the deck to the transport position.  
2. Lower the deck onto a set of equal height blocks  
under the rear corners of the deck. Place an-  
other set of blocks under the front of the deck so  
that the deck top is pitched forward 1/8".  
NOTE: The front and rear of the deck are at different  
heights.  
3. Measure the height of the blade cutting edge  
above the ground. Remove pin B and set the  
height of cut lever E to that height  
4. Loosen nuts on bolts G. Move bolts in slot to  
remove slack in chain. Tighten nuts on bolts G.  
HEIGHT OF CUT  
The height of cut is set by moving height of cut pin B  
to the hole designated for the height of cut desired.  
To change the height of cut:  
1. Lift the deck to the highest position.  
2. Move pin B to the selected hole.  
3. Lower the deck until the lift lever is stopped by  
the pin.  
NOTES:  
-
Height of cut may vary due to the amount of  
tread on the tires, tire diameter or inflation pres-  
sure.  
DECK ROLLERS  
The deck rollers are adjustable up and down to  
provide improved deck flotation and scalping protec-  
tion at various heights of cut. They are not intended  
to ride continuously on the ground. Adjust no closer  
than 3/8" (10mm) to the ground.  
Height of cut ranges for roller adjustment  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADJUSTMENTS  
WOODS  
PARKING BRAKE  
FOR 36", 42", 48", AND 52" MODELS  
NOTE: There are 2 brakes, 1 on each transaxle.  
The parking brake should keep the machine from  
moving. To check the parking brake, park the ma-  
chine on a level surface, open the bypass valves and  
set the parking brake to ON. Attempt to move the  
machine forward and backward by pushing it. If the  
machine moves, adjust the parking brake linkage as  
follows:  
1. Move the machine to a flat horizontal surface.  
2. Grip the flats on the brake rod A. Tighten nut  
B on the brake rod until you run out of threads.  
See Figure 1 for detailed view.  
3. Move the parking brake handle to the OFF  
position.  
FIGURE 1  
4. Loosen nut X.  
5. Hold brake arm in the OFF position as shown in  
Figure 2.  
6. Adjust swivel U until swivel stud meets brake arm  
hole in the OFF position.  
7. Insert cotter pin into swivel U.  
8. Tighten nut X.  
9. Repeat Steps 1-8 on the opposite side.  
FIGURE 2  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADJUSTMENTS  
WOODS  
PARKING BRAKE  
FOR 61" MODELS  
NOTE: There are 2 brakes, 1 on each transaxle.  
The parking brake should keep the machine from  
moving. To check the parking brake, park the ma-  
chine on a level surface, open the bypass valves and  
set the parking brake to ON. Attempt to move the  
machine forward and backward by pushing it. If the  
machine moves, adjust the parking brake linkage as  
follows:  
1. Move the machine to a flat horizontal surface.  
2. Grip the flats on the brake rod A. Tighten nut  
B on the brake rod until you run out of threads.  
See Figure 1 for detailed view.  
B
TIGHTEN UNTIL YOU  
3. Move the parking brake handle to the OFF  
X
RUNOUT OF THREADS  
position.  
FIGURE 1  
4. Loosen nut X.  
5. Hold brake arm in the OFF position as shown in  
Figure 2.  
6. Adjust linkage rod U until formed end of rod  
meets brake arm hole in the OFF position.  
7. Insert cotter pin into formed end of linkage rod U.  
8. Tighten nut X.  
9. Repeat Steps 1-8 on the opposite side.  
FIGURE 2  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADJUSTMENTS  
WOODS  
HYDROSTATIC TRANSAXLE ADJUST-  
MENTS  
A turnbuckle style hydro stat neutral adjustment is  
provided.  
Neutral:  
1. Support the machine with the rear wheels off  
the ground. Use jack stands or equivalent sup-  
port. Do not rely only on mechanical or hydraulic  
jacks.  
2. Move the traction levers out into the neutral lock  
position and raise the seat.  
3. Disconnect the seat switch wire and temporarily  
connect the two terminals with jumper wire J as  
shown.  
4. Start the engine and run at low speed.  
5. Move parking brake to the OFF position.  
6. Loosen jam nuts K at both ends of the control  
rod L.  
7. Rotate the control rod until the corresponding  
wheel stops turning. Lock the control rod jam  
nuts. Run the engine up to high idle and stroke  
the traction levers forward and back to check the  
adjustment. Move traction levers back to neutral  
and readjust if necessary.  
8. Repeat steps 6 and 7 for the opposite side.  
9. Remove the jumper wire and reconnect the seat  
switch.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADJUSTMENTS  
WOODS  
ARM REST HEIGHT ADJUSTMENTS  
1. Remove acorn nuts 1, plastic washers 2, arm  
rest 3 and second set of plastic washers 4.  
2. Adjust carriage bolts 5 to desired height A, B, or  
C by pushingg on the carriage bolts 5 until they  
are free from the locking slot, adjusting them to  
the desired height and then pulling the carriage  
bolts 5 into the desired locking slot A, B, or C.  
Bolts must be placed into slots a like heights or  
arm rest will not fit.  
C
B
C
B
A
A
3. Re-assemble washers 2 & 4, arm rest 3, and  
acorn nuts 1 in reverse order from disassembly.  
Hold carriage bolts 5 in lockting slots while tight-  
ening acorn nuts 1 to prevent them from falling  
out of the locking slots. Tighten nuts 1 until de-  
sired resistance in arm rest rotation is acheived.  
5
4
3
2
1
4
5
1
2
SEAT ADJUSTMENT  
The seat plate allows from some seat adjustment  
either forward or backward.  
1. Flip seat up.  
2. Use holes 1 or 2 for seat adjustment.  
DO NOT USE holes 3 or 4 due to space restric-  
tions with the document tube.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BELT REPLACEMENT  
WOODS  
NOTE: Always use Woods replacement belts, not general purpose belts. Woods belts  
are specially designed for use on this mower and will normally last longer.  
CUTTERDECK BELT  
1. Remove floorplate.  
2. Set the cutterdeck in a middle height-of-cut posi-  
tion.  
3. Use a 3/8" ratchet and extension to back  
tensioning idler off to remove belt from idler.  
Remove belt from cutterdeck pulleys.  
NOTE: Use the 3/8" ratchet in the square hole A on  
the idler.  
2 SPINDLE DECK  
4. Remove belt from clutch pulley.  
5. Install the new belt by performing these steps in  
reverse order.  
NOTE: 61" cutterdeck may require tension spring  
adjustment after belt installation. See Belt tension  
3 SPINDLE DECK  
BELT TENSION FOR 61" DECK  
All belts are tensioned by spring loaded idlers and do  
not require any adjustment except for the 61"  
cutterdeck. Use the eyebolt to adjust the spring  
length to be between 6 3/4" - 7 1/2" as pictured.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BELT REPLACEMENT  
WOODS  
HYDRO TRANSAXLE DRIVE BELT  
1. Remove cutterdeck belt (see cutterdeck belt  
replacement).  
2. Disconnect wire I at clutch M. Remove bolts J  
and remove torque restraint.  
3. Using a ratchet with a 9/16" socket, place over  
nut at location P. Use the ratchet to rotate it  
enough to remove the transaxle drive belt.  
4. Install a new transaxle drive belt by performing  
these steps in reverse order.  
5. Inspect the fans. Replace if worn or damaged.  
Torque transaxle pulley nut to 28.3-41.6 ft-lbs  
(38-56 Nm).  
6. Reinstall cutterdeck belt (see cutterdeck belt  
replacement).  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
WOODS  
NOTES  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
________________________________________________  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS SECTION  
WOODS  
PARTS  
SECTION  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FRAME-ENGINE/CLUTCH ASSY  
WOODS  
FIGURE 1  
KAW ENGINE  
ONLY  
B & S ENGINE  
ONLY  
10  
15  
16  
17  
1
16  
13  
JUMPER HARNESS  
27  
21  
27  
26  
24  
22  
28  
3
23  
4
29  
2
11  
18  
31  
32  
14 30  
5
8
19  
7
12  
9
6
20  
25  
10  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FRAME-ENGINE/CLUTCH ASSY  
WOODS  
FIGURE 1  
ITM PART NO.  
DESCRIPTION  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
4164364  
4164365  
38666.W  
4164537  
4164329  
ENGINE-18HP KAW  
ENGINE-20HP KAW  
FILTER-FUEL  
FILTER-OIL  
FILTER-AIR  
1
1
12 4144116  
13 48412-01  
14 64197-005 BLT-TDFM 3/8-16X1-1/4  
15 64006-02  
(USED ON MODEL CZ2361B ONLY)  
CLUTCH-ENGINE PULLEY  
CLAMP  
1
1
4
LOCKWASHER-HELICAL 5/16 1  
(USED ON MODELS 9CZ2048K)  
16 64163-55  
17 64223-11  
WSHR .328X.75X14 GA  
SCH CAPSCREW M8-1.25X16 1  
1
4164366  
ENGINE-22HP KAW  
ENGINE-24HP KAW  
FILTER-FUEL  
FILTER-AIR  
FILTER-SAFETY  
FILTER-OIL  
1
1
4164367  
38666.W  
4164630  
4164631  
4164537  
(USED ON MODEL CZ2361B ONLY)  
18 4144112.7 WLDMT-CLUTCH BRACKET  
19 4163309  
20 64123-78  
1
1
1
PULLEY-ENGINE  
BOLT-HEX 7/16-20X2-1/2  
(USED ON MODELS CZ2252K & CZ2461K)  
(USED ON 942299F, 942404F & 942405F)  
4163987  
38666.W  
4164152  
4164153  
ENGINE-23HP B&S  
FILTER-FUEL  
ELEMENT-AIR  
FILTER-OIL  
1
1
21 69053-13 HOSE-HTDRO, 3/8X14"  
1
(ITEMS 22-23 USED ON KAW ENGINES ONLY)  
22 64266-02  
NUT-FL LOCK M8-1.25  
2
6
(USED ON MODEL CZ2361B)  
23 64263-002 BLT-FLG HD M6-1.0 X 16  
4163705  
4163715  
2722214  
38666.W  
ENGINE- KAI 17HP  
ELEMENT-AIR FILTER  
FILTER-OIL  
24 4164442.7 BRKT-MUFFLER LH  
* 4164443.7 BRKT-MUFFLER RH  
(USED ON MODELS CZ2048K, CZ2252K, &  
CZ2461K)  
1
1
FILTER-FUEL  
(USED ON MODEL CZ1736K)  
4118507.7 BRKT-MUFFLER LH  
* 4118508.7 BRKT-MUFFLER RH  
(USED ON MODEL CZ1736K)  
1
1
2
4164386  
MUFFLER-KAW  
(USED ON MODEL CZ2048K)  
1
1
1
4164385  
MUFFLER -KAW  
25 64123-55  
BLT-HEX 5/16-18X3  
1
(USED ON MODELS CZ2252K & CZ2461K)  
(USED ON MODEL CZ2461B & CZ2461K ONLY)  
4163913  
(USED ON MODEL CZ2361B)  
MUFFLER-B&S  
26 4164251  
27 88042-03  
VAILVE-OIL DRAIN  
CLAMP-HOSE  
1
2
1
28 4164252-001 FITTING-3/8NP TO BARB  
4149239  
MUFFLER-KAW  
(USED ON MODEL CZ1736K)  
29 11061-7061 GASKET-MUFFLER  
2
(AVAILABLE FROM KAWASAKI DEALER)  
3
4
64152-23  
38665.W  
1/4-20X3/8 LG SP SCREW  
SOLENOID  
2
1
806425  
GASKET-MUFFLER  
(ITEMS 3 & 4 USED ON CZ2252K, CZ2361B, &  
CZ2461K)  
(AVAILABLE FROM B&S DEALER)  
(ITEMS 30-32 USED ON KAWASAKI UNITS ONLY)  
5
6
7
8
9
38304-03  
BRG-FLANGED PLASTIC  
1
1
2
1
1
3
1
30 64123-16  
31 64163-31  
32 64006-03  
BLT-HEX 3/8-16X1-1/4  
WSHR 25/64X1X12  
LOCKWSHR-3/8 HELICAL  
4
2
4
2721331.7 WLDMT-CLUTCH STOP  
64265-04  
64164-12  
64006-06  
LOCKNUT-M8-1.25  
KEY-1/4X1/4X1 SQ END  
LOCKWASHER-HEL 7/16  
10 64205-001 BLT-MET M8-1.25X20  
11 4164049 S-FRAME W/ LABELS  
* NOT ILLUSTRATED  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRANSAXLE ASSY  
WOODS  
FIGURE 2  
42  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRANSAXLE ASSY  
WOODS  
FIGURE 2  
ITM PART NO.  
DESCRIPTION  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
2
3
4
5
4164049  
4162973  
4163957.7 WLDMT-PULL ARM  
4163819  
4156464  
S-FRAME W/LABELS  
SHAFT-PULLARM MOUNT  
1
1
2
2
1
33 4142752  
TIRE-ASSY 20 X 8 - 10 4 PLY  
2
4142752-01 20X8-10 4 PLY MULTI TRAC TIRE  
4132433-03 WHEEL-10X7  
(USED ON 48" DECKS ONLY)  
ARM-CONTROL  
AXLE-LH  
(INCLUDES ITEMS 4, 25, 26, 27, 32, 39 & 40)  
(USED ON 36", 48" AND 52" DECKS ONLY)  
4163731  
TIRE-ASSY 20 X 6.50 - 10  
2
4163731-01 WHEEL-10X5.375  
6
7
8
9
64163-29  
64123-68  
64025-02  
64270-01  
WASHER  
BOLT-HEX 5/16-18X1  
NUT-HEX 5/16-18  
BOLT-MET, HEX M10-1.5x30  
BOLT, 5/16-18X3/4 HEX  
WASHER .328X.75X14 GA  
SPRING-TENSION  
BLT-HEX 3/8-16 X 2  
END CAP-24 X 7  
2
2
2
1
2
6
1
1
1
4163731-02 TIRE-20X6.5-10 GRASSMASTER  
(USED ON 36" DECKS ONLY)  
4155841  
TIRE-ASSY 20 X 10-10  
2
10 64123-54  
11 64163-55  
12 4164128  
13 64123-67  
14 4128001  
15 64268-02  
16 2228016  
17 64163-31  
18 64123-55  
19 64229-03  
20 4156465  
4132433-01 TIRE-20X10-104PLYTURFMASTER  
4155841-01 WHEEL-10X7  
(USED ON 52" DECKS ONLY)  
4163964  
TIRE-ASSY 23X10.50-12  
2
NUT-FL NYLON LOCK 5/16-18 10  
4158422-01 WHEEEL -4-HOLE W/VALVE  
(USED ON 61" DECKS ONLY)  
PULLEY-IDLER PUMP  
WASHER, 25/64X1X12  
BLT-HEX 5/16-18X3  
LOCKNUT-NYLON 3/8-16  
AXLE-RH  
1
12  
4
1
1
34 64187-03  
35 4133302  
WHEEL NUT 1/2-20  
S-ASSY-IDLER ARM PUMP  
8
1
(INCLUDES ITEMS 36-38)  
(INCLUDES ITEMS 4, 25, 26, 27, 32, 39 & 40)  
(USED ON 36", 48" AND 52" DECKS ONLY)  
36 4128004  
37 64144-40  
38 4128000  
39 64163-61  
40 4163299.7 TRAY-BATTERY  
41 64197-022 BLT-TDFM 3/8-16X3/4  
BEARING-BALL 10X26X8  
SNAP RING-26MM INTERNAL 1  
SEAL-16X26X7  
WASHER  
2
21 4143636  
22 4163276  
23 108055.W  
BELT-TRANSAXLE  
ROD-BATTERY CLAMP  
BATTERY  
1
2
1
1
2
1
3
(OBTAIN LOCALLY)  
42 4163264-01 ADAPTER-90#6MAORB/#6 FORB 1  
24 64123-88  
25* 4142045-06 FILTER-TRANSAXLE  
26* 4163819  
27 4163820  
28 64123-168 BLT-HEX 5/8-11X2-1/2  
29 64163-93  
30 85010N  
31 64229-06  
32 4164048  
BLT-HEX 3/8-16X2-3/4  
4
2
2
2
2
4
4
2
43 4163307  
44 4142808-01 CAP-HYDRO TANK  
45 64268-03  
46 4163772  
ASSY-EXPANSION TANK  
2
2
4
1
SPRING-CONTROL ARM  
ARM-BRAKE  
NUT-FL NYLON LOCK 3/8-16  
TRANSAXLE-LH  
(USED ON 61" DECK ONLY)  
WSHR-.635 X 1.12 X.062  
ZERK, 1/4-28  
LOCKNUT, NYLON 5/8-11  
47 4163771  
TRANSAXLE-RH  
1
1
1
(USED ON 61" DECK ONLY)  
KIT-FAN/PULLEY TRANSAXLE 2  
(USED ON 36", 48", AND 52" DECKS ONLY)  
4164129 KIT-FAN/PULLEY TRANSAXLE 2  
(USED ON 61" DECKS ONLY)  
48* 4164227  
CHARGE PUMP COVER KIT  
(USED ON KAWASAKI ENGINES ONLY)  
*4164228  
CHARGE PUMP COVER KIT  
(USED ON B & S ENGINES ONLY)  
* NOT ILLUSTRATED  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FUEL TANK/BUMPER & CONTROL PANEL  
WOODS  
FIGURE 3  
8
34  
5
6
19  
12  
7
14  
11  
10  
22  
13  
35  
2
9
30  
3
16  
17  
15  
29  
16  
17  
15  
30  
26  
32  
28  
33  
25  
31  
24  
18 / 27  
23  
4
21  
21  
18  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FUEL TANK/BUMPER & CONTROL PANEL  
WOODS  
FIGURE 3  
ITM PART NO.  
DESCRIPTION  
S-FRAME W/LABS  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
2
3
4
4164049  
1
1
1
1
4142840-3 TANK-FUEL RH  
4142841-3 TANK-FUEL LH  
4163041.7 BUMPER  
(USED ON 36", 42", 48" AND 52" DECKS)  
4164221.7 BUMPER  
1
(USED ON 61" DECKS ONLY)  
5
6
7
8
9
4164526  
128010-03 S-COVERED KEY  
128010-01 S-KEY SWITCH NUT 5/8-32  
2721505  
4130320  
S-CONTROL PANEL  
1
1
1
1
SWITCH-PTO  
CAP-FUEL TANK  
2
10 2188178  
11 128010.W  
12 64152-46  
13 64025-15  
SWITCH-RETAINER  
SWITCH, KEY  
SCREW-SLT HH 10-24X1/2  
NUT-HEX #10-24 KEPS  
1
1
2
2
14 64262-001 BLT-FLG HD 1/4-20 X 1/2  
4
15 64123-50  
16 64006-03  
17 64163-69  
BOLT-3/8-16X1 HEX  
WASHER-3/8  
WASHER-FLAT  
10  
10  
10  
4
18 64262-010 BLT-FLG HD 3/8-16 X 3/4  
19 4136792  
20* 4144213  
21 64268-03  
METER-HOUR  
TUBE-FUEL FEED  
NUT-WLF 3/8-16  
1
2
4
22 118020-17 CONTROL-THROTTLE  
1
23 64229-02  
24 48228-2A  
25 64123-54  
LOCKNUT-5/16-18  
CLAMP-3/4 CLIP  
BLT-HEX 5/16-18X3/4  
2
2
2
26 4163901.7 WEIGHT-COUNTER  
27 64262-018 BLT-FLG HD 3/8-16 X 1-3/4  
(USED ON 61" DECKS ONLY)  
1
4
28 4163895.7 CHANNEL-TANK SPACER, LH 1  
(USED ON 61" DECKS ONLY)  
29 4164022.7 CHANNEL-TANK SPACER, RH 1  
(USED ON 61" DECKS ONLY)  
30 64123-50  
31 64229-03  
32 4163880.7 BRKT-TANK MOUNTING  
33 4163905.7 PLATE-WEIGHT  
34 108009-04 CABLE-CHOKE  
BOLT-HEX 3/8-16X1  
NUT-NYLON LOCK 3/16-18  
8
8
2
1
1
1
35 64025-04  
NUT-HEX 3/8-24  
* NOT ILLUSTRATED  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FUEL VALVE & COVER PLATE  
WOODS  
FIGURE 4  
1
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FUEL VALVE & COVER PLATE  
WOODS  
FIGURE 4  
ITM PART NO.  
DESCRIPTION  
S-FRAME W/LABS  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
2
3
4
5
6
7
8
9
4164049  
4142840-1 TANK-FUEL RH  
4142841-1 TANK-FUEL LH  
64197-001 BLT-TDFM 5/16-18X3/4  
4164803.7 COVER-FRAME, REAR  
1
1
1
4
1
6
3
1
2
2
2
88042N  
HOSE CLAMP  
4162977-009 HOSE-1/4 FUEL LINE 24"  
2188161  
4130320  
VALVE-TANK SELECTOR  
CAP-FUEL TANK  
GROMMET-FUEL TANK  
TUBE-FUEL FEED  
10 4132325  
11 4144213  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK LIFT ASSEMBLY  
WOODS  
FIGURE 5  
30  
28  
1
32  
9
25  
10  
17  
9
16  
8
10  
34  
24  
20  
27  
22  
33  
21  
16  
19  
29  
21  
18  
19  
11  
26  
6
11  
7
11  
31  
2
15  
14  
5
14  
23  
4
14  
14  
6
3
16  
17  
14  
12  
15  
2
14  
11  
12  
11  
CUTTERDECK  
13  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK LIFT ASSEMBLY  
WOODS  
FIGURE 5  
ITM PART NO.  
DESCRIPTION  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
2
3
4
5
6
7
8
9
4164049  
S-FRAME W/LABS  
1
4
1
1
2
2
1
1
15  
5
19  
4
64205-060 BOLT-MET M12-1.75X50  
4164565.7 WLDMT-DECKLIFT, FRONT  
4163894.7 WLDMT-DECKLIFT REAR  
4109960  
64221-02  
4163891.7 BRKT-LIFT LINK  
2188143  
64123-50  
WLDMT-DECK LIFT ROD  
E-RING .250  
GRIP  
BOLT-HEX 3/8-16X1  
ZERK, 1/4-28 STR  
LOCKNUT-NYLON 3/8-16  
10 85010N  
11 64229-03  
12 2182356.7 BRACKET-SHAFT HANGER  
13 64205-029 BLT-MET M12X1.75X40  
4
14 64246-04  
15 2188127  
16 64163-65  
17 64221-04  
NUT-WHIZ M12-1.75  
CHAIN-6.35 (.250) 5 LINKS  
WASHER-.890X1.375X18GA  
E-RING.875  
16  
4
10  
5
18 4143575.7 BRKT-OUTER DECK LIFT  
19 2183071-03 SPACER-15.88X10.32X24  
20 4163893.7 LEVER-DECK LIFT  
1
2
1
21 64168-2  
22 64188-53  
23 4139785  
24 2720544  
25 64123-67  
26 4126611  
COTTER-HAIRPIN.08X1.19  
PIN-CLEVIS 1/2X1.0  
MAT-FOOT LIFT  
SPRING-COMPRESSION  
BLT-HEX 3/8-16X2  
2
1
1
1
1
1
LABEL-H.O.C. OUTER,  
27 4162904.7 WLDMT-LVR STOP LATCH  
1
28 64163-31  
29 64175-05  
30 64123-82  
31 4159060  
32 2720743  
33 4159284  
34 64163-29  
35 64018-3  
WASHER  
1
1
1
1
1
1
1
PUSHNUT-1/2 DIA  
BOLT-HEX 3/8-16X2-1/2  
ASSY, PIN & LANYARD  
LBL-HT CUT INNER  
ROD-LIFT STOP  
WASHER-21/64X1X11GA  
BLT-CRG 3/8-16X1  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CASTER ASSEMBLY  
WOODS  
FIGURE 6  
19  
20  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CASTER ASSEMBLY  
WOODS  
FIGURE 6  
ITM PART NO.  
DESCRIPTION  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
2
3
4
5
6
7
8
9
4164049  
4162986  
85010N  
64025-20  
64163-26  
S-FRAME W/LABS  
DUST COVER  
ZERK-1/4-28  
NUT-HEX 3/4-16 SLOT U  
WASHER  
1
2
2
2
2
4
4
2
2
48043-03C CUP-OUTER BEARING  
48043-04C CONE-OUTER BEARING  
48480.W  
SEAL  
4143675.7 WLDMT-CASTER  
(USED ON 36", 42", 48" AND 52" DECKS ONLY)  
2721306.7 WLDMT-CASTER  
(USED ON 61" DECKS ONLY)  
10 64229-06  
LOCKNUT-NYLON 5/8-11  
2
2
4
(USED ON 36", 42", 48" AND 52" ONLY)  
11 64123-212 BOLT-5/8-11X6.00  
(USED ON 36", 42", 48" AND 52" ONLY)  
12 2722231  
13 2722233  
SPACER-END  
WHEEL-11"ASSY-LT TYPE  
2
(USED ON 36", 42", 48" AND 52" ONLY)  
2722228 WHEEL-ASSY 13x5.00-6  
2
(USED ON 61" ONLY)  
14 4162945.7 WLDMT-CSTR MOUNTING  
(USED ON 48" & 52" ONLY)  
1
1
1
4162974.7 WLDMT-CSTR MOUNTING  
(USED ON 36" & 42" ONLY)  
4163578.7 WLDMT-CSTR MOUNTING  
(USED ON 61" ONLY)  
15 64123-16  
16 64229-03  
17 2722230-01 SPANNER-11" WHEEL  
(USED ON 36", 42", 48" AND 52" ONLY)  
2722230-02 SPANNER-13" WHEEL  
(USED ON 61" ONLY)  
BLT-HEX 3/8-16X1-1/4  
LOCKNUT-NYLON 3/8-16  
8
8
2
18 304636  
19 64123-215 BLT-HEX 3/4-10 X 7 1/2  
(USED ON 61" ONLY)  
COTTER PIN  
2
2
20 64229-07  
LOCKNUT-NYLON 3/4-10  
2
(USED ON 61" ONLY)  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
KICKPLATE/SEAT ASSEMBLY  
WOODS  
FIGURE 7  
2
4
6
5
5
3
20  
18  
23  
13  
12  
24  
8
19  
22  
8
9
7
1
11  
12  
9
12  
10  
16  
17  
14  
21  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
KICKPLATE/SEAT ASSEMBLY  
WOODS  
FIGURE 7  
ITM PART NO.  
DESCRIPTION  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
2
4164049  
4163703  
*4163703-01 SEAT BACK  
*4163703-02 SEAT BOTTOM  
*4163703-03 ARM REST PAD  
S-FRAME W/LABS,  
SEAT ASSY.  
1
1
1
1
2
1
1
*4163703-04 LH ARM MOUNTING BRKT  
*4163703-05 RH ARM MOUNTING BRKT  
3
4
5
6
7
8
9
4163281.7 PLATE-SEAT  
1
1
4
2
2
4
4
3
2
7
1
2
2
1
2
1
1
1
1
2
1
1
1
4124009  
64268-02  
33138-09  
64144-30  
4143354  
64141-6  
SWITCH-SEAT NO  
NUT-NY LOCK 5/16-18  
PIN-CLEVIS GRVD .38 X 1.31  
SNAP RING .375  
BUMPER, SEAT MOUNTING  
NUT-5/16-18  
10 2722325  
11 148082-20 FUSE-20 AMP  
12 64197-015 BLT-TDFM 10-32X1/2  
RELAY-40AMP SEALED  
13 2188154  
14 64123-16  
15 64229-03  
16 4164549.25 PLATE-FRONT REMOVABLE  
17 64197-005 BLT-TDFM 3/8-16X1-1/4  
18 4164776  
19 4164480  
20 4164479  
21 4142266  
22 64152-27  
23 4129802  
24 38061A  
25 *970391  
MODULE-DELAY  
BLT-HEX 3/8-16X1-1/4  
NUT-NYL LOCK 3/8-16  
S-FOOT PLATE  
MAT-FOOT PLATE UPPER  
MAT-FOOT PLATE LOWER  
CONNECTOR-12V RECEPT  
1/4-20X5/8 LG SP SCREW  
TUBE-DOCUMENT  
CAP-VINYL  
KIT-LIGHT ACCESSORY  
* NOT ILLUSTRATED  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEERING  
WOODS  
FIGURE 8  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEERING  
WOODS  
FIGURE 8  
ITM PART NO.  
DESCRIPTION  
GRIP-HANDLE  
4156297.7 LEVER-TRACTION CNTRL  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
2
3
4144705  
2
2
1
1
30 64123-69  
31 64123-68  
32 64123-50  
BOLT-5/16-18X1-1/2 HEX  
BOLT-HEX 5/16-18X1  
BLT-HEX 3/8-16X1  
2
2
4
2
4
2
2
2
2
2
2
4
1
1
1
1
2
2
2
4156295  
WLDMT-CONTROL BAR, RH  
WLDMT-CONTROL BAR, LH  
* 4156294  
33 64123-105 BLT-HEX 1/4-20X1-5/8  
34 64237-05  
35 4133156  
36 64061-25  
37 4143595-01 ROD END-FEMALE RH  
38 4143595-02 ROD END-FEMALE LH  
39 64025-03  
40 64144-30  
41 64229-02  
42 4147116.7 LINK-BRAKE  
43 4155482.7 WLDMT-BRAKE ARM  
44 4147196  
45 41-010  
LOCKNUT-NYLON M8-1.25  
SPACER  
ROLL PIN  
4
5
6
7
8
9
4143673.7 WLDMT-CONTROL BOX RH  
4143674.7 WLDMT-CONTROL BOX LH  
108208.W  
64197-015 BLT-TDFM 10-32X1/2 TORX  
4127142  
64221-03  
1
1
2
4
5
6
1
2
2
2
SWITCH DBL POLE  
BSHG-CONTROL ARM  
E-RING 19MM/.750  
BAR-CONTROL PIVOT  
DAMPENER  
ROD-CONTROL  
ROD-PARKING BRAKE  
NUT-HEX 5/16-24  
SNAP RING  
LOCKNUT-NYLON 5/16-18  
10 4143676  
11 2721246  
12 4143571  
13 4144525  
SPACER  
SPRING-TENSION  
NUT-FL NYLON LOCK 1/4-20  
(USED ON 36", 42", 48" AND 52" ONLY)  
46 64268-01  
14 4155661.7 LINK-PARKING BRAKE RH  
* 4155660.7 LINK-PARKING BRAKE LH  
1
1
47 64251-002 WASHER-M6  
48 4164075  
WLDMT-RODPARKINGBRAKE  
(USED ON 61" ONLY)  
15 4145589  
SWIVEL-3/8-16  
2
(USED ON 36", 42', 48" AND 52" ONLY)  
49 4164024  
ROD-PARKING BRAKE  
(USED ON 61" ONLY)  
2
16 4155481  
SPRING-COMPRESSION  
LOCKNUT-NYLON 3/8-16  
NUT-3/8-16 HEX  
2
2
2
1
17 64268-03  
18 64025-05  
19 4156465  
TRANSAXLE-RH  
(USED ON 36", 42', 48", AND 52" ONLY)  
* NOT ILLUSTRATED  
4163772  
TRANSAXLE-RH  
(USED ON 61" ONLY)  
20 4156464  
TRANSAXLE-LH  
1
(USED ON 36", 42', 48" AND 52" ONLY)  
4163771  
TRANSAXLE-LH  
(USED ON 61" ONLY)  
21 4164049  
22 4146988.7 BRKT-CNTRL BAR SUPT  
S-FRAME W/LABS  
1
1
2
2
2
2
2
1
2
23 64229-01  
24 64123-89  
25 4146187  
26 64025-33  
27 4145106  
LOCKNUT-1/4-20 NYLON  
BOLT-HEX 1/4-20X3/4  
BEARING-FLANGE  
NUT-HEX 5/16-24 LH  
SPACER-CONTROL ROD  
28 4155483.7 BRAKE, ARM LINKAGE  
29 64168-2 COTTER-HAIRPIN  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARKING BRAKE  
WOODS  
FIGURE 9  
2
17  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARKING BRAKE  
WOODS  
FIGURE 9  
ITM PART NO.  
DESCRIPTION  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
2
4164049  
4156464  
S-FRAME W/LABST  
TRANSAXLE, RH  
1
1
(USED ON 36", 42", 48", AND 52" ONLY)  
3
4
5
6
7
8
9
64197-015 BLT-TDFM 10-32X1/2 TORX  
2
2
2
1
1
1
1
1
1
1
1
2
2
2
1
64168-2  
4148697  
4146187  
64221-03  
2188155  
COTTER-HAIRPIN.08X1.19  
ROD-BYPASS CONTROL  
BEARING-FLANGE  
E-RING 19MM/.750  
GRIP  
4163060.7 HANDLE-BRAKE FASTCAT  
10 64163-34  
11 64006-01  
12 64123-89  
13 2188156  
WASHER  
LOCKWASHER  
BOLT-HEX 1/4-20X3/4  
SWITCH-NONO DBL POLE  
14 4148698.7 LINK-DUMP VALVE  
15 2720977  
16 64229-01  
17 4163772  
SPRING-COMPRESSION  
LOCKNUT-1/4-20 NYLON  
TRANSAXLE, RH 61" ONLY  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRE HARNESS  
WOODS  
FIGURE 10  
1
2
ELECTRIC  
CLUTCH  
20  
11  
15  
ENGINE  
WIRE COLORS  
WHITE  
WB WHITE W/ BLACK STRIPE  
W
3
4
MAGNETO  
STARTER SOL YB  
OIL PRESS  
CHARGING  
W
SOLENOID  
STARTER  
GROUND  
P
O
PURPLE  
ORANGE  
OB ORANGE W/ BLACK STRIPE  
PO PURPLE W/ ORANGE STRIPE  
OP ORANGE W/ PURPLE STRIPE  
DB DARK BLUE  
BLACK  
GREEN  
RED  
G
P
17  
(RED)  
16  
TO SOLENOID (2)  
16  
B
G
R
Y
YELLOW  
YB YELLOW W/ BLACK STRIPE  
RW RED W/ WHITE STRIPE  
GY GREEN W/ YELLOW STRIPE  
BR BROWN  
8
BRY BROWN W/ YELLOW STRIPE  
BLADES  
&
TRACTION  
RELAY  
8
STARTER  
RELAY  
12  
TO ENGINE BLOCK  
(GROUND)  
BATTERY  
BATTERY  
8
DELAY  
RELAY  
6
(RED)  
3
(BLACK)  
DELAY  
MODULE  
18  
ENGINE BLOCK  
(GROUND)  
9
16  
TO SOLENOID (1)  
TO SOLENOID (4)  
FUSES  
14 GA  
14 GA  
14 GA  
14 GA  
2
7
SWITCH  
KEY  
OFF  
RUN  
M+G  
B+L  
START B+L+S  
14 GA  
14 GA  
14 GA  
10  
SWITCH  
CLUTCH  
HOUR  
METER  
CARB  
SOLENOID  
MAGNETO  
PACKARD  
5
#02962793  
VOLTAGE  
REGULATOR  
12V  
ADAPTER  
W
G
P
P
14 GA  
14 GA  
19  
SWITCH  
TRACTION  
CONTROL  
Y
TO SOLENOID (3)  
13  
4
SWITCH  
SEAT  
21  
13  
SWITCH  
TRACTION  
CONTROL  
14  
SWITCH  
BRAKE  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRE HARNESS  
WOODS  
FIGURE 10  
ITM PART NO.  
DESCRIPTION  
HARNESS-MAIN WIRE  
148082-20 FUSE 20 AMP  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
2
3
4
5
6
4154880  
1
2
1
1
1
1
30-419  
CABLE-BATT 4 GA BLK 29"  
SWITCH-SEAT NO  
METER-HOUR  
4124009  
4136792  
30-180  
CABLE-BATT 4 GA RED 29"  
(USED ON 22HP, 23HP, AND 24HP ONLY)  
2722227-02 CABLE-BATTERY W/COND  
(USED ON 18HP AND 20HP ONLY)  
1
7
8
9
128010.W  
2722325  
2188154  
SWITCH, KEY  
RELAY-40AMP SEALED  
MODULE-DELAY  
1
3
1
1
1
1
2
1
1
10 2721505  
11 4144116  
12 30-184  
13 108208.W  
14 2188156  
15 38665.W  
SWITCH-PTO  
CLUTCH-ELECTRICAL  
COVER-POS TERMINAL  
SWITCH DBL POLE  
SWITCH-NONO DBL POLE  
SOLENOID  
(USED ON 17HP, 22HP, 23HP, AND 24HP  
ONLY)  
16 2308095  
17 108061-04 CABLE-BATTERY 20 RED  
(USED ON 22HP, 23HP, AND 24HP ONLY)  
COVER-TERMINAL  
3
1
18 2188225  
WIRE-GROUND  
1
1
(USED ON 22HP, 23HP, AND 24HP ONLY)  
19 2188224  
HARNESS-JUMPER  
(USED ON 17HP, 22HP AND 24HP ENGINES  
ONLY)  
2722013  
HARNESS-JUMPER  
1
1
(USED ON 23HP B&S ENGINES ONLY)  
4164496  
HARNESS-JUMPER  
(USED ON 20HP ENGINES ONLY)  
20 2720949  
21 158136  
22* 56-081-36  
ASSY-CLUTCH WIRE  
WIRE-SEAT SWITCH  
SLEEVING, ID 0.77 NYLON  
1
1
1
* NOT ILLUSTRATED  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
36" SIDE DISCHARGE  
WOODS  
FIGURE 11  
15  
16  
17  
5
36  
14  
15  
10  
16  
17  
9
5
4
11  
10  
24  
25  
36  
14  
6
26  
12  
13  
4
27  
28  
29  
32  
8
18  
7
6
30  
43  
19  
38  
42  
42  
43  
1
46  
44  
44  
31  
21  
31  
21  
41  
21  
45  
23  
21  
2
20  
21  
39  
34  
16  
22  
3
35  
TORQUE TO  
70 FT-LBS  
33  
37  
37  
40  
37  
37  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
36" SIDE DISCHARGE  
WOODS  
FIGURE 11  
ITM PART NO.  
DESCRIPTION  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
2
3
4
5
6
7
4152858  
4147115  
S-36 DECK W/LABELS  
CHUTE-RUBBER  
1
1
2
2
2
2
1
41 4149017.7 HINGE-CHUTE_RUBBER  
42 4147757.7 COVER-BELT 36  
1
2
4
4
2
1
112111-02KT2 BLADE 18.00 OFFST HLFT  
43 64139-08  
44 64141-6  
BOLT-5/16-18X3/4 WLF  
FLANGE NUT, 5/16-18 NC ZP  
4115850  
4144947  
128169  
S-ASSY SPINDLE OUTER  
PULLEY-SPINDLE  
PULLEY, IDLER 5.50  
ARM, DECK IDLER ASSY  
45 64262-013 BLT-FLG HD 3/8-16 X 1-1/2  
46 64144-36 E-CLIP  
4146065  
(INCLUDES ITEMS 28-30)  
8
9
2308133  
2721096  
SPRING-EXTENSION  
HOUSING-SPINDLE  
1
2
(INCLUDES ITEMS 10 - 13)  
10 38348-01  
11 2183070-02 SHAFT-SPINDLE  
12 64144-38  
13 38315  
14 64262-012 BLT-FLG HD 3/8-16 X 1-1/4  
15 64123-208 BLT-HEX 5/8-18X1.5  
16 64209-03  
17 64164-12  
18 64268-05  
19 4152578-01 SPACER  
20 64123-31  
21 64123-50  
BEARING-SPINDLE SEALED  
4
2
2
2
12  
2
4
2
1
1
1
7
2
2
1
1
1
1
1
2
1
14  
4
1
1
1
4
8
1
2
2
SNAP RING  
NUT-SPINDLE  
SPRING WASHER  
KEY-1/4X1/4X1 SQ END  
NUT-FL NYLON LOCK 1/2-13  
BOLT-1/2-13X3 HEX  
BOLT-HEX 3/8-16X1  
22 64123-187 BLT-HEX 5/8-18 X 3 3/4  
23 4118314  
24 64123-90  
25 64006-05  
26 4128002  
27 64270-01  
28 64144-40  
29 4128004  
30 4127999  
31 64229-03  
32 64163-19  
33 4115864.7 BAFFLE-DISCHARGE  
34 4134343.7 BAFFLE-RIGHT FRONT  
35 4147035.7 BAFFLE-FRONT DECK  
36 64163-84  
37 64268-03  
38 64018-3  
39 64018-2  
40 64229-01  
SPACER-BLADE 16MM  
BOLT, 1/2-20X2 HEX  
LOCKWSHR-HELICAL 1/2  
END CAP  
BOLT-MET M10-1.5 X 30  
SNAP RING  
BEARING  
SEAL  
LOCKNUT-NYLON 3/8-16  
WASHER  
WASHER  
NUT-FL NYLON LOCK 3/8-16  
BOLT-3/8-16X1 CARRIAGE  
BLT-CRG 1/4-20X3/4  
LOCKNUT-1/4-20 NYLON  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
48" SIDE DISCHARGE  
WOODS  
FIGURE 12  
57  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
48" SIDE DISCHARGE  
WOODS  
FIGURE 12  
ITM PART NO.  
DESCRIPTION  
S-48 DECK W/LABELS  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
2
3
4
5
6
7
8
9
4146864  
1
1
1
1
9
2
41 4120175.7 BAFFLE-FRONT LH  
42 4134336.7 BAFFLE-FRONT CENTER  
43 4134342.7 BAFFLE-RIGHT FRONT  
44 4120208.7 BAFFLE-DISCHARGE  
45 64018-3  
46 64268-03  
1
1
1
1
1
4146596.25 GUARD-LH 48" DECK  
4146595.25 GUARD-RH 48" DECK  
4147115  
64123-50  
64018-11  
64229-03  
CHUTE-RUBBER  
BOLT-HEX 3/8-16X1  
BOLT-CRG 1/2-13X3LG  
LOCKNUT-NYLON 3/8-16  
BOLT-3/8-16X1 CARRIAGE  
NUT-FL NYLON LOCK 3/8-16 10  
BLT-CRG 1/4-20X3/4  
LOCKNUT-1/4-20 NYLON  
WASHER  
25 47 64018-2  
48 64229-01  
16 49 64163-84  
4
4
6
A/R  
2
1
64205-029 BLT-MET M12X1.75X40  
64246-04  
8
NUT-WHIZ M12-1.75  
CHAIN-6.35 (.250) 5 LINKS  
PULLEY-SPINDLE  
10 2188127  
11 4144947  
12 112111-01KT BLADE 16.25 OFFST HLFT  
13 64262-012 BLT-FLG HD 3/8-16 X 1-1/4  
4
3
3
50 64163-19  
51 38524.W  
52 4149017.7 HINGE-CHUTE_RUBBER  
WASHER  
KNOB-4 PRONG  
18 53 64144-36  
E-CLIP  
1
14 64209-03  
15 64164-12  
16 128169  
SPRING WASHER.67 ID  
KEY-1/4X1/4X1 SQ END  
PULLEY, IDLER 5.50  
6
3
3
1
54 4163332  
55 64141-13  
56 64123-31  
ROLLER-ANTI SCALP  
NUT WLF 1/2-13  
BLT-HEX 1/2-13X3  
2
4
2
1
17 4147896  
ARM-DECK IDLER ASSY  
57 4163514.7 GUIDE-BELT  
(INCLUDES ITEMS 30-32)  
18 4115850  
S-ASSY SPINDLE OUTER  
3
(INCLUDES ITEMS 25-29)  
19 64006-05  
20 64123-05  
21 4118314  
22 64123-187 BLT-HEX 5/8-18 X 3 3/4  
23 64123-208 BLT-HEX 5/8-18X1.5  
24 2308133  
25 38348-01  
26 2721096  
27 64144-38  
28 38315  
LOCKWSHR-HELICAL 1/2  
BLT-HEX 1/2-20X1-1/2  
SPACER-BLADE 16MM  
1
1
3
3
3
1
6
3
3
3
3
1
2
1
1
1
1
2
2
1
1
1
SPRING-EXTENSION  
BEARING-SPINDLE SEALED  
HOUSING-SPINDLE 6 HOLE  
SNAP RING  
NUT-SPINDLE  
29 2183070-02 SHAFT-SPINDLE  
30 4127999  
31 4128004  
32 64144-40  
33 64270-01  
34 4128002  
35 4152578-01 SPACER  
36 64262-013 BLT-FLG HD 3/8-16 X 1-1/2  
37 64268-05  
38 64018-30  
39 2721512  
40 2720685  
SEAL  
BEARING  
SNAP RING  
BOLT-MET M10-1.5 X 30  
END CAP  
NUT-FL NY LOCK 1/2-13  
BOLT-CARRIAGE  
ROLLER  
SPACER-ROLLER  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
52" SIDE DISCHARGE  
WOODS  
FIGURE 13  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
52" SIDE DISCHARGE  
WOODS  
FIGURE 13  
ITM PART NO.  
DESCRIPTION  
S-52 DECK W/LABELS  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
2
3
4
5
6
7
8
9
4153817  
1
1
1
1
9
2
41 4118427.7 BAFFLE-FRONT LH  
42 4134338.7 BAFFLE-FRONT CENTER  
43 4134343.7 BAFFLE-RIGHT FRONT  
44 4115864.7 BAFFLE-DISCHARGE  
45 64018-3  
46 64268-03  
1
1
1
1
1
4143552.25 GUARD-LH 52" DECK  
4143553.25 GUARD-RH 52" DECK  
4147115  
64123-50  
64018-11  
64229-03  
CHUTE-RUBBER ASSY  
BOLT-HEX 3/8-16X1  
BOLT-CRG 1/2-13X3LG  
LOCKNUT-NYLON 3/8-16  
BOLT-3/8-16X1 CARRIAGE  
NUT-FL NYLON LOCK 3/8-16 10  
BLT-CRG 1/4-20 X 3/4  
LOCKNUT-1/4-20 NYLON  
WASHER  
24 47 64018-2  
48 64229-01  
16 49 64163-84  
4
4
6
64205-029 BLT-MET M12X1.75X40  
64246-04  
8
NUT-WHIZ M12-1.75  
10 2188127  
11 4144947  
12 112111-02  
CHAIN-6.35 (.250) 5 LINKS  
PULLEY-SPINDLE  
BLADE 18.00 OFFST HLFT  
4
3
3
50 64163-19  
51 38524.W  
52 4149017.7 HINGE-CHUTE_RUBBER  
E-CLIP  
54 4163514.7 GUIDE-BELT  
WASHER  
KNOB-4 PRONG  
A/R  
2
1
1
1
13 64262-012 BLT-FLG HD 3/8-16 X 1-1/4  
18 53 64144-36  
14 64209-03  
15 64164-12  
16 128169  
SPRING WASHER.67 ID  
KEY-1/4X1/4X1 SQ END  
PULLEY, IDLER 5.50  
6
3
3
1
17 4147896  
ARM-DECK IDLER ASSY  
(INCLUDES ITEMS 30-32)  
18 4115850  
S-ASSY SPINDLE OUTER  
3
(INCLUDES ITEMS 25-29)  
19 64006-05  
20 64123-90  
21 4118314  
22 64123-187 BLT-HEX 5/8-18 X 3 3/4  
23 64123-208 BLT-HEX 5/8-18X1.5  
24 2308133  
25 38348-01  
26 2721096  
27 64144-38  
28 38315  
LOCKWSHR-HELICAL 1/2  
BLT-HEX 1/2-20 X 2  
SPACER-BLADE 16MM  
1
1
3
3
3
1
6
3
3
3
3
1
2
1
1
1
1
2
2
3
3
3
SPRING-EXTENSION  
BEARING-SPINDLE SEALED  
HOUSING-SPINDLE 6 HOLE  
SNAP RING  
NUT-SPINDLE  
29 2183070-02 SHAFT-SPINDLE  
30 4127999  
31 4128004  
32 64144-40  
33 64270-01  
34 4128002  
35 4152578-01 SPACER  
36 64262-013 BLT-FLG HD 3/8-16 X 1-1/2  
37 64268-05  
38 64018-30  
39 2721512  
40 2720685  
SEAL  
BEARING  
SNAP RING  
BOLT-MET M10-1.5 X 30  
END CAP  
NUT-FL NY LOCK 1/2-13  
BOLT-CRG 3/8-16 X 4-1/2  
ROLLER  
SPACER-ROLLER  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61" SIDE DISCHARGE  
WOODS  
FIGURE 14  
40  
69  
33  
22  
19  
18  
11  
70  
27  
55  
32  
14  
17  
57  
58  
41  
24  
66  
62  
25  
44  
15  
57  
67 36  
10  
28  
59  
52  
60  
21  
11  
54  
21  
6
11  
35  
34  
38  
63  
34  
3
7
38  
4
16  
8
30  
29  
7
39  
23  
13  
31  
35  
45  
9
35  
2
56  
35  
35  
26  
7
37  
40  
35  
7
43  
53  
69  
50  
45  
12  
64  
47  
45  
4
16  
65  
5
TORQUE TO  
70 FT. LBS  
20  
51  
53  
53  
47  
47  
53  
61  
53  
48  
46  
53  
46  
49  
48  
42  
53  
53  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61" SIDE DISCHARGE  
WOODS  
FIGURE 14  
ITM PART NO.  
DESCRIPTION  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
2
3
4
5
6
7
8
4164130  
S-61" DECK  
1
1
1
2
1
1
28  
2
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68*  
64163-55 WSHR .328X.75X14 GA  
1
1
7
4
7
4
1
1
1
1
4163809.25BELT COVER RH  
4163808.25BELT COVER LH  
38524.W KNOB-4 PRONG 3/8-16  
4147399  
64158-08 EYE BOLT  
64229-03 LOCKNUT NYLON 3/8-16  
64123-31 BLT-HEX 1/2-13X3  
2721512  
548138  
128169  
112111-03KTBLADE 21.00 OFFST HLFT  
2720685 SPACER-ROLLER  
64262-012 BLT-FLG HD 3/8-16 X 1-1/4  
4164094.7 WLDMT-IDLER ARM  
64018-33 BLT-CRG 1/2-13 X 4-1/2  
4163514.7 GUIDE-BELT  
64006-05 LOCKWSHR-1/2 HELICAL  
64123-90 BLT-HEX 1/2-20X2  
4115864.7 BAFFLE-DISCHARGE  
64268-05 NUT-FL NYLON LOCK 1/2-13 2  
64164-12 1/4X1/4X1 SQ END KEY  
4163332  
4115849  
(INCLUDES ITEMS 57-60, & 62)  
4163586  
SPRING-EXTENSION  
64123-114 BLT-HEX 1/4-20X1  
64018-2  
64141-2  
BLT-CRG 1/4-20X3/4  
NUT-WLF 1/4-20  
CHUTE-RUBBER ASSY  
64229-01 LOCKNUT-1/4-20 NYLON  
4134340.7 BAFFLE-FRONT CTR 61  
4117663.7 BAFFLE-FRONT LH  
4163441.7 EXTENSION-61IN, LH  
9
ROLLER-5X2.75 CENTERED 5  
BRGNDL.881.121.00OPENEND 2  
PULLEY IDLER 5.50  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
4163014  
SPACER  
3
3
5
18  
1
2
1
1
1
1
64268-03 NUT-FL NYLN LOCK 3/8-16 10  
4163155  
64144-40 SNAP RING  
64018-3 BOLT-3/8-16X1 CARRIAGE  
INNER RING  
2
1
1
38348-01 BEARING-SPINDLE SEALED 6  
2721096 HOUSING-SPINDLE 6 HOLE 3  
64144-38 SNAP RING  
38315 NUT-SPINDLE  
4163440.7 EXTENSION-61IN, RH  
2183070-01 SHAFT-SPINDLE LONG  
4163030.7 WLDMT-IDLER PIN  
3
3
1
3
1
2
1
3
2
64262-013 BLT-FLG HD 3/8-16 X 1-1/2  
4149017.7 HINGE-CHUTE RUBBER  
ROLLER, ANTI-SCALP  
S-ASSYSPNDL ZT200 CNTR 3  
85010N  
64141-6  
ZERK-1/4-28 STR SLF THRD 1  
NUT-WLF 5/16-18  
1
1
64123-217 BLT-HEX 3/8-16X4 - 1/4  
25  
4164095 ASSY-IDLER ARM  
1
4
(USED ON REAR CENTER ANTI-SCALP ROLLER)  
(INCLUDES ITEMS 10, 15, 28, 41, 55, 66)  
64141-13 NUT-WLF 3/8-24  
64270-02 BOLT-HEXM10-1.5X30ISOCL10.9 1  
521438 GREASE SEAL  
64205-029 BLT-METRIC M12X1.75X40  
2188127 CHAIN-6.35 (.250) 5 LINKS  
64246-04 NUT-WHIZ M12-1.75  
69  
70  
64209-03 SPRING WASHER .67 ID  
6
4
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
4128002  
END CAP- 26X7  
1
4
4
8
3
3
2
12  
1
3
2
4
3
1
1
*NOT ILLUSTRATED  
4149197  
4163804  
4163802  
PULLEY-SPINDLE  
SPACER-1.015X1.75X1.50  
SPACER-1.0X.516X1-15/16  
64123-50 BOLT-HEX 3/8-16X1  
64229-02 LOCKNUT-NYLON 5/18  
4118314  
SPACER-BLADE 16MM  
64163-74 WSHR-.516X2X.25THK PLT  
64018-30 BLT-CRG 3/8-16 X 4-1/2  
64123-208 BLT-HEX 5/8-18X1.5  
4128004  
BEARING  
4134344.7 BAFFLE-RIGHT FRONT  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BELTS-CUTTERDECK  
WOODS  
FIGURE 15  
5
2
3
4
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BELTS-CUTTERDECK  
WOODS  
FIGURE 15  
ITM PART NO.  
DESCRIPTION  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
2
3
4
5
4144212  
4143733  
4147095  
4163569  
4147716  
BELT-36" CUTTERDECK  
BELT-52" CUTTERDECK  
BELT-48" CUTTERDECK  
BELT-61" CUTTERDECK  
BELT-42" CUTTERDECK  
1
1
1
1
1
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECALS-POWERUNIT  
WOODS  
FIGURE 16  
5 (UNDER SEAT)  
16  
4
7
2
9
6
8
1
18  
18  
4
10  
14  
17  
12  
3
(UNDER FOOTPLATE)  
11  
13  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECALS-POWERUNIT  
WOODS  
FIGURE 16  
ITM PART NO.  
DESCRIPTION  
qTY ITM PART NO.  
DESCRIPTION  
qTY  
1
2
3
4
5
6
7
8
9
4144768  
2000570  
4164525  
4152340  
2000590  
2000701  
2000700  
4126804  
4147617  
LABEL-CONTROL PANEL  
LABEL-WARN FUEL PICT.  
LABEL-INFORMATION  
LABEL-WOODS  
LABEL-WARN BATTERY  
LABEL-LH TRACTION  
LABEL-RH TRACTION  
LABEL-PARKING BRAKE  
LABEL-FUEL TANK VALVE  
LABEL-WARNING  
LABEL-DANGER/WARNING  
LABEL-HOC INNER  
LABEL, WARNING  
LABEL-HOC OUTER  
LABEL-MANUAL LOCATION  
LABEL-MAINTENANCE  
LABEL-WOODS CZ  
LABEL-CZ1736K  
1
2
1
2
1
1
1
1
1
1
2
1
3
1
1
2
1
10 4164279  
11 4164269  
12 2720743  
13 2000577  
14 4126611  
15 4146936  
16 4133980  
17 4152003  
18 4164835  
4164831  
LABEL-CZ2048K  
4164832  
LABEL-CZ2252K  
4164833  
LABEL-CZ2361B  
4164834  
LABEL-CZ2461K  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
(Mow’n Machine Zero-Turn Mowers and Woods Boundary Utility Vehicles)  
TM  
TM  
Please Enter Information Below and Save For Future Reference.  
Date Purchased: __________________________  
Model Number: __________________________  
From (Dealer):______________________________________  
Serial Number: _____________________________________  
WHAT IS COVERED:  
TM  
TM  
Woods Equipment Company (“WOODS”) warrants Mow’n Machine zero-turn mowers and attachments and Woods Boundary utility  
vehicles, accessories and attachments to be free from defect in material and workmanship for the warranty periods listed below.  
FOR HOW LONG:  
Mow’n Machine Model #CZ1736K, CZ1948K, CZ1952K, CZ2361, ME1952K, ME2661B, MZ2552K, MZ2561K, MZ2761, MZ3761K,  
MZ3772K, MZ2661KL & attachments are warranted for two (2) years from the date of delivery to the original purchaser or 2000 hours of  
operation, whichever occurs first. Purchaser may opt for a warranty of five (5) years from the date of delivery to the original purchaser or 500  
hours of operation, whichever occurs first. The dealer must specify the special warranty term on the original, dated bill of sale and a copy must  
be provided with all warranty claims. Mow’n Machine model numbers CZR2242B and CZR2652B are warranted for residential use for three (3)  
years from the date of delivery to the original purchaser or for commercial use for 90 days from the date of delivery to the original purchaser..  
Mow’n Machine Model #FE21B, FZ21D, FZ23B, FZ25D, FZ28K & attachments are warranted for two (2) years from the date of delivery to the  
original purchaser or 2000 hours of operation, whichever occurs first.  
In addition, Mow’n Machine ME and MZ Series Models, serial number XXXXXXXX300 and above, have a Limited Lifetime Warranty on deck,  
deck cradle, and engine deck for the life of the machine to the original retail purchaser.  
Woods Boundary utility vehicle Model #MAV350, MAV480, MAV4x4, accessories & attachments are warranted for two (2) years from the date  
of delivery to the original purchaser.  
IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION  
TO THE DURATION OF THE WRITTEN WARRANTY PERIODS LISTED ABOVE. Some states do not allow limitations on how long an  
implied warranty lasts, so the above limitation may not apply to you.  
WHO IS COVERED:  
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer the product to a  
third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.  
WHAT IS NOT COVERED:  
This Warranty does not cover normal wear or tear, or normal maintenance items, or any damage, failure or loss caused by:  
1. Improper operation, improper maintenance, misuse, or an accident;  
2. Any modification or repair by someone other than WOODS, a WOODS’ authorized dealer or distributor, and/or a WOODS’  
authorized service center; or  
3. Repairs made with parts other than those obtained through WOODS.  
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories with respect to which the  
manufacturer provides a separate warranty.  
WHAT WOODS WILL DO TO CORRECT PROBLEMS:  
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if the product  
is defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30) days  
after such defect or noncompliance is discovered or should have been discovered, routed through the dealer and distributor from whom the  
purchase was made, transportation charges prepaid. WOODS shall complete such repair or replacement within a reasonable time after WOODS  
receives the product.  
OTHER LIMITATIONS:  
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the  
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal  
theory. Without limiting the foregoing, WOODS shall not be liable for any damages relating to (i) lost profits, business, revenues or goodwill;  
(ii) any expense or loss incurred for labor, supplies, substitute machinery or rental; or (iii) any other type of damage to property or economic loss.  
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you.  
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company, including without limitation, WOODS, its  
authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty.  
HOW STATE LAW APPLIES:  
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
QUESTIONS:  
Answers to any questions regarding warranty service and locations may be obtained by contacting:  
Woods Equipment  
Company  
2606 South Illinois Route 2  
Post Office Box 1000  
Oregon, Illinois 61061  
800-319-6637 tel  
800-399-6637 fax  
www.WoodsEquipment.com  
F-8045 MM & Boundary (Rev. 12/1/2008)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
TM  
(Mow’n Machine Zero-Turn Mower and  
TM  
Woods Boundary Utility Vehicle Replacement Parts)  
TM  
Woods Equipment Company (“WOODS”) warrants replacement parts for Mow’n Machine zero-turn  
TM  
mowers and attachments and Woods Boundary utility vehicles, accessories and attachments to be free  
from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the  
product to the original purchaser.  
IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR  
PURPOSE ARE LIMITED IN DURATION TO A PERIOD OF NINETY (90) DAYS FROM THE  
DATE OF DELIVERY OF THE PRODUCT TO THE ORIGINAL PURCHASER. Some states do not  
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.  
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser  
sell or otherwise transfer the product to a third party, this Warranty does not transfer to the third party  
purchaser in any way. There are no third party beneficiaries of this Warranty.  
This Warranty does not cover normal wear or tear, or normal maintenance items, or any damage, failure  
or loss caused by improper operation, improper maintenance, misuse, or an accident.  
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement,  
free of charge, of the product if the product is defective or in noncompliance with this Warranty. The  
product must be returned to WOODS with proof of purchase within thirty (30) days after such  
defect or noncompliance is discovered or should have been discovered, routed through the dealer  
and distributor from whom the purchase was made, transportation charges prepaid. WOODS  
shall complete such repair or replacement within a reasonable time after WOODS receives the product.  
WOODS shall not be liable for any incidental or consequential losses, damages or expenses,  
arising directly or indirectly from the product, whether such claim is based upon breach of  
contract, breach of warranty, negligence, strict liability in tort or any other legal theory. Without  
limiting the foregoing, WOODS shall not be liable for any damages relating to (i) lost profits, business,  
revenues or goodwill; (ii) any expense or loss incurred for labor, supplies, substitute machinery or rental;  
or (iii) any other type of damage to property or economic loss. Some states do not allow the exclusion or  
limitation of incidental or consequential damages, so the above limitations may not apply to you.  
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,  
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is  
authorized to alter, modify, or enlarge this Warranty.  
This Warranty gives you specific legal rights, and you may also have other rights which may vary from  
state to state.  
Answers to any questions regarding warranty service and locations may be obtained by contacting:  
Woods Equipment  
Company  
2606 South Illinois Route 2  
Post Office Box 1000  
Oregon, Illinois 61061  
800-319-6637 tel  
800-399-6637 fax  
www.WoodsEquipment.com  
F-8495 MM & Boundary Repair Parts (Rev. 2/15/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Woods Equipment  
Company  
2606 South Illinois Route 2  
Post Office Box 1000  
Oregon, Illinois 61061  
800-319-6637 tel  
800-399-6637 fax  
www.WoodsEquipment.com  
©2008 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and “Tested. Proven. Unbeatable.” are trademarks  
of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that  
appear in this manual are the property of their respective companies or mark holders. Specifications subject to change without notice.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Brinly Hardy Lawn Mower Accessory PCT 10LX ATV BH User Manual
Dixon Lawn Mower 13087 0400 User Manual
Dixon Lawn Mower ZTR 7523 User Manual
Hayter Mowers Lawn Mower 447F User Manual
Karcher Lawn Sweeper KMR 1250 BAT User Manual
McCulloch Lawn Mower MC30 (96022001300) User Manual
Scag Power Equipment Lawn Mower SMT 72V User Manual
Sears Lawn Aerator S A 4 0 0 B H User Manual
Snapper Lawn Mower FC Series User Manual
Stiga Lawn Mower 8211 3417 04 User Manual