MOW’N MACHINE
MZ2252K
872500G
22HP KAW W/52” SIDE DISCHARGE
(S/N 00050 AND ABOVE)
MZ2661K
872502G
26HP KAW W/61” SIDE DISCHARGE
(S/N 00050 AND ABOVE)
Includes Maintenance
Instructions
RF4166232
Download from Www.Somanuals.com. All Manuals Search And Download.
WOODS
IMPORTANT MESSAGE
TO THE DEALER:
Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual
instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in
the Set-Up instructions are completed before releasing equipment to the owner.
The dealer must complete the Product Registration online at the Woods Dealer Website or complete the
mail-in form included with the Operator’s Manual. If using the mail-in form, the dealer is to return the prepaid
postage portion to Woods, give one copy to the customer, and retain one copy. Failure to register the product
does not diminish customer’s warranty rights.
TO THE OWNER:
Read the Operator’s Manual before operating your Woods equipment. The information presented will prepare
you to do a better and safer job. Keep the manual handy for ready reference. Require all operators to read
the Operator’s Manual carefully and become acquainted with all adjustment and operating procedures before
attempting to operate the equipment. Replacement manuals can be obtained from your dealer. To locate
your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and
Canada call 1-800-319-6637.
The equipment you have purchased has been carefully engineered and manufactured to provide dependable
and satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as
specified. Observe all safety information in this manual and safety decals on the equipment.
For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the
necessary tools and equipment to handle all your needs.
Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards
required for safe and satisfactory operation. Record the model number and serial number of your equipment
in the spaces provided:
Model: _______________________________ Date of Purchase: _____________________
Serial Number: (located below seat near left hand corner) ____________________________________
Provide this information to your dealer to obtain correct repair parts.
™
ALITEC
®
BMP
®
CENTRAL FABRICATORS
®
GANNON
®
GILL
®
WAIN-ROY
®
WOODS
See MAN0866 for Operator’s Manual
12-2010
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
WOODS
TABLE OF CONTENTS....................................................FIGURES ........................................................................PAGE
SAFETY.........................................................................................................................................................................5
ASSEMBLY AND SETUP..........................................................................................................................................6, 7
MAINTENANCE CHART ..............................................................................................................................................8
MAINTENANCE RECORD............................................................................................................................................9
MAINTENANCE ....................................................................................................................................................10-16
ADJUSTMENTS.....................................................................................................................................................17-21
BELT REPLACEMENT ...............................................................................................................................................22
SPECIFICATIONS..................................................................................................................................................23-26
PARTS SECTION........................................................................................................................................................27
UPPER ENGINE DECK ASSY/CLUTCH ..........................FIGURE 1...................................................................28, 29
OWER ENGINE DECK ASSY/CLUTCH............................FIGURE 2...................................................................30, 31
BUMPER ...........................................................................FIGURE 3...................................................................32, 33
FUEL TANKS/CONTROL PANEL......................................FIGURE 4...................................................................34, 35
BRAKES/REAR WHEEL...................................................FIGURE 5...................................................................36, 37
OIL COOLER.....................................................................FIGURE 6...................................................................38, 39
HYDRAULICS ...................................................................FIGURE 7...................................................................40, 41
HYDROGEAR PUMP........................................................FIGURE 8...................................................................42, 43
KAWASAKI WIRE HARNESS ...........................................FIGURE 9...................................................................44, 45
SEAT ASSEMBLY & ROPS...............................................FIGURE 10.................................................................46, 47
FOLDING ROPS KIT.........................................................FIGURE 11.................................................................48, 49
STEERING/DECK LIFT.....................................................FIGURE 12.................................................................50, 51
CRADLE ASSEMBLY........................................................FIGURE 13.................................................................52, 53
CRADLE & CASTER ASSEMBLY.....................................FIGURE 14.................................................................54, 55
52” SIDE DISCHARGE......................................................FIGURE 15.................................................................56, 57
61” SIDE DISCHARGE......................................................FIGURE 16.................................................................58, 59
BELTS-CUTTERDECK......................................................FIGURE 17.................................................................60, 61
DECALS-POWER UNIT....................................................FIGURE 18.................................................................62, 63
DECALS-CUTTERDECKS................................................FIGURE 19.................................................................64, 65
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
WOODS
This symbol means:
ATTENTION!
BECOME ALERT!
NOTICE !!!
Unauthorized modifications may present extreme
safety hazards to operators and bystanders and
could also result in product damage.
Your safety and the safety of others is involved.
Woodsstronglywarnsagainst,rejectsanddisclaims
any modifications, add-on accessories or product
alterations that are not designed, developed, tested
and approved by Woods Engineering Department.
Any Woods product that is altered, modified or
changed in any manner not specifically authorized
after original manufacture-including the addition of
“after-market” accessories or component parts not
specifically approved by Woods-will result in the
Woods Warranty being voided.
Signal word definitions:
The signal words below are used to identify levels
of hazard seriousness. These words appear in this
manual and on the safety labels attached to Woods
machines. For your safety and the safety of others,
read and follow the information given with these
signal words and/or the symbol shown above.
Anyandallliabilityforpersonalinjuryand/orproperty
damage caused by any unauthorized modifications,
add-on accessories or products not approved
by Woods will be considered the responsibility
of the individual(s) or company designing and/
or making such changes. Woods will vigorously
pursue full indemnification and costs from any party
responsibleforsuchunauthorizedpost-manufacture
modifications and/or accessories should personal
injury and/or property damage result.
DANGER indicates a hazardous situation which, if
not avoided, WILL result in death or serious injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, COULD result in
death or serious injury.
CAUTION indicates a hazardous situation which,
if not avoided, COULD result in minor or moderate
injury. It may also be used to alert against unsafe
practices or property damage.
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which, if
not avoided, MAY result in property damage
MODEL NUMBER: This number appears on
sales literature, technical manuals and price lists.
SERIAL NUMBER: This number appears only
on your mower. It contains the model number
followed consecutively by the serial number.
Use this number when ordering parts or seeking
warranty information.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY AND SETUP
WOODS
TOOLS REQUIRED FOR ASSEMBLY
-
-
-
-
-
-
-
-
Wrecking bar
Claw hammer
Ratchets: 3/8”,e
Sockets: 9/16”, 3/4"
Wrenches: 3/8", 9/16", 3/4"
Straight edge
Tire pressure gauge
Blocks (for deck leveling)
NOTE: All references below to the “right” or “left” are with respect to an operator at the controls.
1. UNCRATE UNIT
Discard packing materials. Remove and discard shipping brackets. Tighten caster wheel axle bolts
against caster axle spanner bushings.
2. Set rear tire pressures to 12 lbs/in2 (1.0 kg/cm2). Tires are overinflated for shipping. Front tires are run flat
tires
3. DECK LEVELING
a) Park the machine on a smooth, level surface.
Raise the deck to the transport position.
b) Lower the deck onto a pair of equal height blocks
A under the rear corners of the deck. Place an-
other pair of adjustableblocks B under the front of
the deck so that the deck top is pitched forward
1/8”.
NOTE: The front and rear of the deck are at different
heights.
c) Measure the height of the blade cutting edge
above the ground. Remove pin C and set the
height of cut lever D to that height.
d) Loosen nuts I at all four corners of the deck.
NOTE: This will relieve tension on chains H.
e) Loosen the jam nuts E on the height of cut clips
F and adjusting screws G. Turn the adjusting
screws G until the play is taken out of the chains
H at all four corners. Tighten the jam nuts E
against the clips F and at the adjusting screws G.
Retighten nuts I at this time.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY AND SETUP
WOODS
6. COUNTERBALANCE SPRINGS
a) Raise the cutterdeck all the way.
b) Adjust the spring A with nut B:
Approximately 1" of threads should be extending
past the spring mounting bracket at nut B.
The springs may be tightened or loosened from
this point according to personal preference.
7. FINAL PREPARATIONS
-
Check the engine and hydraulic oil levels. Top up with the correct oil if necessary. Use SAE 10W30
motor oil for the engine. Use fresh, clean SAE 15W40 or SAE 20W50 motor oil or SAE 15W50 synthetic
motor oil for the hydraulic system.
-
Remove the battery from the machine. Fill the battery to the bottom of the vent wells with acid and trickle
charge for several hours.
Battery acid is caustic and fumes are explosive and can cause serious injury or death.
Use insulated tools, wear protective glasses or goggles and protective clothing when working with batteries.
Read and obey the battery manufacturer’s instructions.
Be certain the ignition switch is OFF and the key has been removed before servicing the battery.
a) Verify battery polarity before connecting or disconnecting the battery cables.
b) When installing the battery, always assemble the RED, positive ( + ) battery cable first and the
ground,
BLACK, negative ( - ) cable last.
c) Tighten cables securely to battery terminals and apply a light coat of silicone dielectric grease to
terminals and cable ends to prevent corrosion. Keep terminal covers in place.
-
-
Read Operation and Safety Manual before starting.
Run engine at full RPM for 5 minutes before engaging blades to allow the engine to be fully lubricated
before load is applied.
-
-
Check the hydrostat neutral adjustment. Neutral is set at the factory but may require readjustment if
air trapped during the initial oil fill has worked out of the system. See adjustments section later in this
manual.
Do not use the machine without an approved grass collector, the grass discharge chute or mulching
plates correctly fitted.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE CHART
WOODS
Maintenance is an ongoing job. These intervals are maximum times between
maintenance operations. Perform more often under severe conditions.
MAINTENANCE
OPERATION
EVERY
25
EVERY
50
EVERY
100
EVERY
200
EVERY
500
FIRST 5
HOURS
DAILY
HOURS
HOURS
HOURS
HOURS
HOURS
ENGINE
Consult the engine manual for additional information and instructions
Check/Top Off
Engine Coolant
Level
X
(Where Applicable)
Check/Top Off
Oil Level
X
X
X
Check For Leaks
Clean Air Intake
Screen
Clean Air Cleaner
Precleaner
X*
Clean Air Cleaner
X
X
X**
Element
Clean Cooling Fins
Change Oil And
Filter
X
See engine manufacturer's manua
l
Check/Replace
Spark Plugs
X
*
R
N/A IF EQUIPPED WITH HEAVY DUTY CYCLONIC AIR CLEANE
**IF EQUIPPED WITH HEAVY DUTY CYCLONIC AIR CLEANER
HYDRAULICS
Check For Leaks
X
Check/Top Off
X
Oil Level
Change Oil And
Filter
X
X
MACHINE
Check Interlock
Operation
X
X
Check Tire
Pressures
Check/Top Off
Battery
X
X
Lubricate All Points
X
8
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE RECORD
WOODS
NOTES
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
________________________________________________
DATE
HRS
DATE
HRS
DATE
HRS
DATE
HRS
DATE
HRS
DATE
HRS
GENERAL
Check Tire Pressures
Lubricate All Points
Check Nuts & Bolts
ENGINE
Check Engine Coolant
Level
(Where Applicable)
Check Oil Level
Change Oil
Clean
Air Cleaner Element
Clean Cooling Fins
Replace
Air Cleaner Element
Clean & Gap
Spark Plugs
NOTE: After first 5 hours of operation replace engine oil, hydraulic oil and both filters.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
WOODS
CHECK DAILY
Operator Presence Interlock System - Start Operation
For the engine to crank, the parking brake must be on, the PTO (blades) off and traction levers in the neutral
lock position. Sit in the seat and check, one by one, if the engine will crank with the parking brake off, the
blades on, and either traction lever out of neutral lock. Also, make sure engine coolant temperature gauge
light flashes upon turning key to the ON position.
Operator Presence Interlock System - Run Operation
The operator must be in the seat for the engine to run with the parking brake off, the traction levers moved out
of the neutral lock position, or the blades on. To check:
1. Start the engine and run at 1/2 throttle with the operator on the machine but raised off the seat.
2. One by one: move the parking brake to the OFF position, traction levers out of the neutral lock position
(check each independently), and turn the blades on. Each check should kill the engine after 1/2 second.
(A 1/2 second delay is built into the system to prevent engine cutout when traversing rough terrain.)
Repair machine before using if the Operator Presence Interlock System does not operate correctly in start or
run. Contact your authorized BOB-CAT dealer.
Hardware
Tighten any nuts and bolts found loose. Replace any broken or missing cotter pins. Repair any other
problems before operating.
Tire pressure
Rear tires should be kept inflated at 12 lbs/in2 (1.0 kg/cm2). Improper tire inflation can cause rapid tire wear
and poor traction. Uneven inflation can cause uneven cutting.
BATTERY
4. Check the electrolyte level every 100 hours of
operation.
Battery acid is caustic and fumes
are explosive and can cause serious injury or death.
5. Clean the cable ends and battery posts with steel
wool. Use a solution of baking soda and water
to clean the battery. Do not allow the solution to
enter into the battery cells.
Use insulated tools, wear protective glasses or
goggles and protective clothing when working with
batteries. Read and obey the battery manufacturer’s
instructions.
6. Tighten cables securely to battery terminals and
apply a light coat of silicone dielectric grease to
terminals and cable ends to prevent corrosion.
Keep terminal covers in place.
Be certain the ignition switch is OFF and the key has
been removed before servicing the battery.
1. Verify battery polarity before connecting or dis-
connecting the battery cables.
2. When installing the battery, always assemble
the RED, positive ( + ) battery cable first and the
ground, BLACK, negative ( - ) cable last.
3. When removing the battery, always remove the
ground, negative ( - ) cable first and the red, posi-
tive ( + ) cable last.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
WOODS
6
1
2
2
2
4
5
4
3
2
2
6
LUBRICATION
Every 50 hours of operation, lubricate the following points (1-4) with grease:
1. Deck lift rockshaft (1 point)
2. Deck lift pivots (6 points)
3. Brake lever pivot (1 point)
4. Push arms (2 points located at rear of cutterdeck under each fuel tank)
5. Isolation mounts (4 points located under seat at front of machine.
6. Caster wheel pivots (2 points)
(Lubricate every 500 hours or once a year)
NOTE ON BLADE SPINDLES - The blade spindles on these machines use a superior sealed bearing that
does not require relubrication.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
WOODS
HYDRAULIC SYSTEM
Fluid level in the hydraulic system should be checked
after the first 5 hours of operation, and every 100
hours thereafter, or when a leak has occurred. If the
fluid is low, check all components for leaks.
To check, remove reservoir cap M. The fluid level
should be at the bottom of the filler tube. If low, top
up (do not overfill). Use one of the oils listed below:
–
–
–
SAE 15W40 motor oil
SAE 20W50 motor oil
15W50 synthetic motor oil
AFTER FIRST FIVE (5) HOURS
1. Remove plug N to drain hydraulic reservoir. Dis-
pose of used oil in accordance with local require-
ments.
2. Clean and replace the plug.
3. Change hydraulic oil filter G.
4. Fill the reservoir with fresh oil to the bottom of
the reservoir filler tube, using an oil from the list
above. Do not overfill.
PERIODIC OIL CHANGES
Change the hydraulic fluid and hydraulic filter
after each 500 hours of operation using the same
procedure given above.
NOTES:
View from below machine
Before servicing the hydraulic system, stop the engine,
disconnect spark plug wires and disengage the PTO.
–
After any hydraulic line is opened, plug or cap it
promptly to reduce the risk of contamination.
Do not use sealant tape on hydraulic pipe fittings.
Use a liquid sealant that will dissolve into the
system.
–
–
Make sure all hydraulic connections are tight and
hydraulic hoses and lines are in good condition
before applying pressure to system.
The machine's hydraulic system operates under high
pressure. When checking for leaks, do not use your
hands to attempt to find a leak. Instead, use card-
board or paper. Escaping hydraulic fluid can be under
sufficient pressure to penetrate skin and cause serious
injury. If hydraulic fluid is injected into the skin, it must
be promptly removed by a doctor familiar with this form
of injury or gangrene may result.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
WOODS
ENGINE OIL
Do not perform engine maintenance without the
engine off, spark plug wires disconnected and PTO
disengaged.
AFTER FIRST FIVE (5) HOURS
While the engine is warm:
1. Release the oil drain hose assembly from the
engine clip J. Lay hose assembly over the frame
edge.
2. Remove the rubber cap D from the tip of the
hose assembly and turn the drain valve to allow
oil to drain from the engine. Dispose of used oil
in accordance with local requirements.
3. Clean drain valve and tighten the plastic portion
of the drain valve back into the metal portion of
the valve. Replace rubber cap over the tip of the
valve. Replace hose assembly back into engine
clip.
4. Change oil filter.
5. Fill the crankcase with fresh oil to the full mark.
Do not overfill. See engine manual for oil
specifications.
PERIODIC OIL CHANGES
DAILY
1. See engine manual for oil and filter change inter-
vals after the break-in period.
1. Check oil level with the dipstick.
2. If oil is needed, add fresh oil of proper
viscosity and grade. See engine manual for oil
specifications. Do not overfill.
2. Follow instructions for first oil change, above.
3. Replace dipstick before starting engine.
SPARK PLUGS
Remove each plug and check condition.
–
–
Good operating conditions are indicated if the plug has a light coating of grey or tan deposit.
A white blistered coating indicates overheating. A black coating indicates an “over rich” fuel mixture. Both
may be caused by a clogged air cleaner or improper carburetor adjustment.
–
Do not sandblast, wire brush or otherwise attempt to repair a plug in poor condition. Best results are
obtained with a new plug.
–
Set plug gap as specified in engine manual..
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
WOODS
FUEL FILTER
An inline fuel filter is located in the fuel supply line. Inspect at every oil change to make sure it is clean and
unobstructed. Replace if dirty.
ENGINE COOLING
Continued operation with a clogged cooling system
will cause severe overheating and can result in en-
gine damage.
-
Daily: Clean air intake screen S on air cooled
engines and T on liquid cooled engines.
-
Every 100 hours: Clean cooling fins beneath
blower housing H with reference to information in
the engine manufacturer's manual.
HEAVY DUTY CYCLONIC AIR CLEANER
Clean and replace the air cleaner element as
specified in the service chart. Uneven running, lack
of power or black exhaust fumes may indicate a dirty
air cleaner.
To replace air cleaner elements:
1. Unclamp end cover X and remove existing
cleaner elements.
2. Insert new elements Y and Z and replace cover.
Ensure the breathing port A is pointing down and
towards the front of the tractor.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
WOODS
CLEANING MACHINE
Clean the machine after use. Compressed air is
recommended. Do not use a pressure washer. The
machine will run cooler and last longer if kept free of
clippings and other debris. A clean machine also re-
duces the risk of fire due to accumulation of combus-
tible debris and chaff.
Brush or blow clippings and debris off the cutterdeck
and engine deck. DO NOT use a pressure washer.
WASHING MACHINE
CAUTION: Improperly washing a machine can cause
water to enter bearings and other components. This
can greatly reduce component life.
–
Do not use a pressure washer. Do not direct
water at bearings or seals. High pressure water
can blow past seals and enter sealed bearings.
–
–
Allow the machine to cool down before washing.
Water on a warm machine can be sucked into
sealed bearings as they cool.
Avoid getting electrical connections wet. Water
can cause electrical faults and corrosion of elec-
trical components.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
WOODS
BLADE REMOVAL
BLADE BALANCE
Follow these instructions to prevent injury during
blade removal:
1. Loosen with a box wrench or a socket and long
breaker bar. To gain additional leverage, slip a
long pipe or thick-walled tube over breaker bar or
wrench.
Blade balance must be maintained at 5/8 oz-in
(19.4 g-cm) or less. Failure to keep blades balanced
causes excess vibration, wear, and shortened life of
most components of the machine.
To balance a blade:
2. Insert wood block A as shown, with grain
perpendicular to blade, to prevent blade from
turning when loosening.
3. Wear thickly padded gloves. Keep hands clear
of blade path. Blades may rotate when bolt
releases.
1. Sharpen blade first.
2. Balance the blade at the center.
3. Attach a 1/8 oz (3.9 g) weight at a distance 5”
(127 mm) from center on the light end. This
should make the light end the heavy end:
-
-
If it does, the blade is balanced.
If does not, file or grind the heavy end until
the addition of the weight makes the light end
the heavy end.
BLADE INSTALLATION
1. Wear thickly padded gloves to prevent cuts from
the sharp blade.
2. Insert the blade bolt, in order, through the conical
washer (cup side toward the blade, as shown),
the blade, and the blade spacer.
3. Install assembly on the blade spindle.
4. Torque the blade bolt to 70 ft-lbs.
SHARPENING
Blades may be sharpened by filing or grinding.
-
-
-
Inspect blades before sharpening.
Replace bent or cracked blades.
Replace blades when the lift portion has worn
thin.
-
-
-
Maintain cut angle at 30o.
Do not overheat blades when sharpening.
Always use BOB-CAT blades. Use of another
manufacturer’s blades may be dangerous.
BELTS
All belts are tensioned by spring loaded idlers. No adjustment is required.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
WOODS
DECK LEVELING
a) Park the machine on a smooth, level surface.
Raise the deck to the transport position.
b) Lower the deck onto a pair of equal height blocks
A under the rear corners of the deck. Place
another pair of adjustable blocks B under the
front of the deck so that the deck top is pitched
forward 1/8”.
NOTE: The front and rear of the deck are at different
heights.
c) Measure the height of the blade cutting edge
above the ground. Remove pin C and set the
height of cut lever D to that height.
d) Loosen nuts I at all four corners of the deck.
NOTE: This will relieve tension on chains H.
e) Loosen the jam nuts E on the height of cut clips
F and adjusting screws G. Turn the adjusting
screws G until the play is taken out of the chains
H at all four corners. Tighten the jam nuts E
against the clips F and at the adjusting screws G.
Retighten nuts I at this time.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
WOODS
HEIGHT OF CUT
The height of cut is set by moving height of cut pin C
to the hole designated for the height of cut desired.
To change the height of cut:
1. Lift the deck to the highest position.
2. Move pin C to the selected hole.
3. Lower the deck until the lift lever is stopped by
the pin.
NOTES:
–
–
Height of cut may vary due to the amount of
tread on the tires, tire diameter or inflation pres-
sure.
For best results, adjust the rear deck rollers for
the height of cut to be used (see below).
REAR DECK ROLLERS
The rear outside deck rollers are adjustable up and
down to provide improved deck flotation and scalp-
ing protection at various heights of cut. They are not
intended to ride continuously on the ground. Adjust
no closer than 3/8” (10mm) to the ground.
Height of cut ranges for roller adjustment
COUNTERBALANCE SPRINGS
1. Raise the cutterdeck all the way.
2. Adjust the spring A with nut B: The spring length
should be set at approximately 8-3/4", inside loop
to inside loop, when in transport position.
The springs may be tightened or loosened from
this point according to personal preference.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
WOODS
CONTROL LEVERS
There are two mounting positions for the control
levers, upper and lower. The lower position works
well for most people. Taller operators may need the
upper position.
To adjust the height of the control levers:
-
-
Remove bolts A and nuts B.
Align holes in control lever D with appropriate
holes in traction lever bracket C.
Install bolts A and nuts B.
-
The upper mounting hole for the control levers is
slotted to allow fore-aft adjustment and to allow
alignment of the levers.
To adjust or align the control levers:
-
-
-
Loosen nuts B.
Adjust control lever position.
Tighten nuts B.
PARKING BRAKE
NOTE: Parking brake must be in the OFF position to
properly seat brake drums.
Park machine on a smooth level surface.
Support the machine with the rear wheels off the
ground, using jack stands or equivalent. DO NOT
rely on mechanical or hydraulic jacks.
1. Remove rear wheels.
2. Measure spring length O with parking brake N in
the OFF position.
3. Move parking brake N to the ON position and
measure length of spring O again. When spring
deflects 3/8" it is properly adjusted.
4. If adjustment is required, return parking brake N
to the OFF position.
5. Disconnect one end of rod M at the brake and
loosen jam nut.
6. Adjust rod M in or out as required until 3/8" de-
flection in brake spring O is achieved with park-
ing brake N in the ON position.
Parking brake assembly (tire and deck not shown
for clarity - brake in ON position).
7. Reconnect rod M and retighten jam nut.
8. Repeat steps 2-7 on opposite side of machine.
9. Replace wheels and tighten wheel nuts.
This adjustment will cause the brake springs to
stretch 3/8" when the parking brake is in the ON posi-
tion, providing the correct parking brake force without
overloading the brake arm.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
WOODS
TRACKING HANDLES
An adjustment is provided to allow the operator to
adjust machine tracking during operation.
1. Turn knob W clockwise to shorten control lever
travel.
2. Turn knob W counter-clockwise to increase con-
trol lever travel.
DAMPERS
Different damper mounting holes have been provided
for various operator preferences with control lever
motion.
1. For a stronger resistance feel, mount the damp-
ers X in the outer most hole Z of the motion
control weldment.
2. For a lighter resistance feel, mount the dampers
X in the inner most hole V of the motion control
weldment.
FRONT DECK LIP
Adjustable front deck lips have been provided on 52
in. and 61 in. cutterdecks for various cutting condi-
tions.
To revise per conditions:
1. Loosen the front bolts S.
2. Adjust height of H.
3. Retighten S once you have desired height.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
WOODS
HYDROSTAT ADJUSTMENTS
A turnbuckle-style hydrostat neutral adjustment is
provided.
Neutral:
1. Support the machine with the rear wheels off
the ground. Use jackstands or equivalent sup-
port. Do not rely only on mechanical or hydraulic
jacks.
2. Move the traction levers out into the neutral lock
position and raise the seat.
3. Disconnect the seat switch wire K and
temporarily connect the two terminals with
jumper wire J as shown.
4. Start the engine and run at low speed.
5. Loosen jam nuts T at both ends of the control
rod.
6. Rotate the control rod until the corresponding
wheel stops turning. Lock the jam nuts. Run the
engine up to high idle to check the adjustment.
Readjust if necessary.
7. Repeat steps 5 and 6 for the opposite side.
8. Remove the jumper wire J and reconnect the
seat switch.
Reverse Return:
1. Move traction levers out to the neutral lock posi-
tion and raise the seat.
2. Locknut U should be run on the bolt as far as it
will go.
Right side adjustments
3. Loosen jam nut Y. Adjust the clevis yoke by
turning the head of the bolt until the clevis pin
just makes contact with the rear of the slot in the
lever it connects with. Tighten jam nut Y.
4. Repeat steps 2 and 3 for the opposite side.
NOTE: A slight creep in reverse is acceptable
provided the wheel does not turn and the hydrostat
pump does not whine when the parking brake is on.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
BELT REPLACEMENT
WOODS
Note: Always use WOODS, Inc.replacement belts, not general purpose belts. WOODS,
Inc.belts are specially designed for use on commercial mowers and will normally last lon-
ger.
CUTTERDECK BELT
1. Tilt floorplate all the way forward.
2. Set the cutterdeck in a middle height-of-cut posi-
tion.
3. Use a 3/8" ratchet and extension to back
tensioning idler off to remove belt from idler.
Remove belt from cutterdeck pulleys.
NOTE: Use the 3/8" ratchet in the square hole A on
the idler.
4. Remove belt from clutch pulley.
5. Install the new belt by performing these steps in
reverse order.
PUMP-DRIVE BELT
1. Remove engine-cutterdeck belt (see engine-cutterdeck belt replacement).
2. Attach an extension to a 3/8" drive ratchet. Insert the ratchet extension in the square hole of the pump
drive idler arm. Use the ratchet handle to rotate it enough to remove the pump drive belt.
3. Install a new pump drive belt in the same manner as it was removed.
4. Re-install engine-cutterdeck belt (see engine-cutterdeck belt replacement).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
WOODS
POWER UNITS
ENGINES:
CONTROLS:
Construction: Aluminum block with cast-in cast iron Throttle; choke; power takeoff (PTO) clutch switch;
sleeves. Aluminum head.
traction levers; parking brake lever; lift lever.
Configuration: 4-stroke, vertical shaft, V-twin cylin-
der, overhead valve, air-cooled.
FUEL SYSTEM:
One tank on each side of operator, each with a shut-
off (1/4 turn). Total capacity 14 gallons (52.9 liters).
Fuel selector/shutoff switch on rear cooler mounting
bracket(1/4 turn). Replaceable fuel filter.
DRIVE SYSTEM:
Full hydrostatic pump and wheel motor combination
for independently controlled drive wheels.
Pump: Hydrogear12cc variable displacement piston
pump.
MAXIMUM GROUND SPEEDS:
Forward: 11.5 mph (18.5 km/h)
Motors: Parker displacement MB series. Direct
drive 1-1/4” (31.8mm) diameter output shaft.
Reverse: 4 mph (6.4 km/h)
Turn Radius: True Zero
WHEELS & TIRES:
Drive wheels:
OPERATOR PRESENCE
INTERLOCK SYSTEM:
872500G:
872502G:
23 X 10.5-12 4-Ply Turf
Tread Tires
Start: The PTO (blades) must be off, traction levers
in neutral lock, and parking brake on for engine to
crank.
24 X 12.00-12 4-Ply Turf
Tread Tires
Run: Operator must be in seat to take parking brake
off, to move traction levers out of the neutral lock
position, or to turn the PTO (blades) on or the engine
will kill. The parking brake must be off for the traction
levers to move out of the neutral lock position.
Casters: 13 X 6.5-6 No-Flat tires
Pressure: 14 p.s.i. (1 kg/cm2)
The operator may leave the seat with the engine
running if the parking brake is on, the PTO (blades)
is off, and the traction levers are in the neutral lock
position. A time delay eliminates annoying engine
cutout from operation over rough terrain.
BRAKING:
Parker brakes. Spring applied for overload
protection.
WEIGHT:
1256 lbs (570 kg) w/52" deck
1293 lbs (587 kg) w/61" deck
SEAT:
High back, foam padded full suspension seat with
standard armrests. Fore and aft adjusters, hinged for
easy tilt-up access to pumps and battery. Internally
mounted seat switch.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
WOODS
ENGINES
872500G
Kawasaki
FX651V
2
MODEL NUMBERS
872502G
Kawasaki
FX703V
2
MANUAFACTURER
MODEL
CYLINDERS
COOLING
Air
Air
3.1 X 3.0"
(78X76mm)
3.1 X 3.0"
(78X76mm)
BORE/STROKE
DISPLACEMENT
COMPRESSION
OUTPUT POWER
OUTPUT TORQUE
LUBRICATION
GOVERNOR
44.3 cu. in.
(726cc)
44.3 cu. in.
(726cc)
8.2:1
8.2:1
22 hp (16.4kw)
@ 3600rpm
26 hp (19.4kw)
@ 3600rpm
40.0 ft-lb(54.2J)
@2200 rpm
42.1 ft-lb(55.4J)
@ 2400 rpm
FULL PRESSURE
Mechanical
FULL PRESSURE
Mechanical
AIR CLEANER
IGNITION SYSTEM
CHARGING SYSTEM
BATTERY
Heavy Duty Cyclonic Heavy Duty Cyclonic
Electronic
Electronic
15 amp, regulated
BCI group U1
15 amp, regulated
BCI group U1
FUSES
Two, 20 amp blade
Two, 20 amp blade
FUEL CONSUMPTION
@ MAX LOAD/SPEED
24
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
WOODS
DATE
HRS
DATE
HRS
DATE
HRS
DATE
HRS
DATE
HRS
DATE
HRS
GENERAL
Check Tire Pressures
Lubricate All Points
Check Nuts & Bolts
ENGINE
Check Engine Coolant
Level
(Where Applicable)
Check Oil Level
Change Oil
Clean
Air Cleaner Element
Clean Cooling Fins
Replace
Air Cleaner Element
Clean & Gap
Spark Plugs
NOTE: After first 5 hours of operation replace engine oil, hydraulic oil and both filters.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
WOODS
CUTTERDECKS
872502G,
872500G
MODEL NUMBER
TYPE
Side Discharge
52.5" (133 cm)
N/A
Side Discharge
61" (155 cm)
N/A
CUTTING WIDTH
WIDTH
WIDTH
(CHUTE UP)
56.25" (143 cm)
62" (157 cm)
WIDTH
(CHUTE DOWN)
64.5" (164 cm)
73" (185 cm)
high lift
(low lift optional)
high lift
(low lift optional)
BLADE
NUMBER OF
BLADES
3
3
BLADE LENGTH
18" (46 cm)
.205" (5.2 mm)
21" (53 cm)
0.25" (6.35 mm)
BLADE THICKNESS
18585 ft/min
5665 m/min
18850 ft/min
5745 m/min
TIP SPEED
@ 3600 Engine RPM
@ 3500 Engine RPM
DAILY PRODUCTION
(8 hr @ 6 mph)
Up to 25.5 acres
(10.3 ha)
Up to 29.5 acres
(11.9 ha)
CONSTRUCTION:
Fabricated and welded 10-gauge, double-layer steel
ANTI-SCALP ROLLERS:
52” Cutterdecks - 6 Rollers
61” Cutterdecks - 7 Rollers
top with 7-gauge side skirts. Full floating design.
CUTTERDECK DRIVE SYSTEM:
Electric clutch/brake drives belt directly from engine
to cutterdeck. No twists in drive belt.
CUTTING HEIGHT & PRODUCTION:
Height: Spring assisted lift lever allows easy setting
of cut heights from 1" to 5 1/2" in 1/4” increments.
“Set and forget” feature allows height of cut to be
set and returned to without searching from operator
position.
SPINDLES:
Top mounted and maintenance free, with 1” shaft in
precision machined, aluminum housing
SPECIFIC TORQUES
BLADE BOLT TORQUE: 70 FT-LBS (95 Nm)
WHEEL HUB NUTS: 225 FT-LBS (237 Nm)
ENGINE CRANKSHAFT BOLT: 50 FT-LBS (68 Nm)
LUG NUTS: 75-100 FT-LBS
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS SECTION
WOODS
PARTS
SECTION
27
Download from Www.Somanuals.com. All Manuals Search And Download.
UPPER ENGINE DECK ASSY
WOODS
FIGURE 1
50
42
41
14
39
44
1
39
31
56
56
55
53
54
40
34
33
2
W A R N I N
G
15
7
2
17
4
30
7
10
13
48
52
36
20
11
51
16
3
12
37
46
38
5
49
8
17
47
17
52
21
19
32
12
43
12
45
29
26
23
6
27
43
25
22
18
9
24
17
37
35
28
28
Download from Www.Somanuals.com. All Manuals Search And Download.
UPPER ENGINE DECK ASSY
WOODS
FIGURE 1
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
4164366
4164368
4164576
4164577
4164537
38666
ENG-KAW 22HP FX
ENG-KAW 26HP FX
S-AIR FILTER PRIMARY
S-AIR FILTER SAFETY
FILTER-OIL
1
44
45
46
47
48
49
50
64263-007 BLT-FLG HD M8-1.25 X 20
64123-15 BOLT-3/8-16X3/4 HEX
64197-025 BLT-TDFM 1/4-20X5/8
38304-02 BRG, FLGD PLASTIC
2
8
2
2
2
1
1
1
4
2
1
1
1
2
4143354
4165236
BUMPER-RUBBER
CAP-RESERVOIR
FILTER-FUEL
PUMP-HYDROSTATIC 12CC
2
4164841
2
4164443.7 BRKT-MUFFLER LH
* 4164442.7 BRKT-MUFFLER RH
64025-15 NUT-HEX #10-24 KEPS
64152-46 SCREW-SLT HH 10-24X1/2
4164252-001 FITTING-3/8NPT TO 3/8
69053-03 HOSE, HYDRAULIC 18"
(SEE FIGURE 8 FOR BREAKDOWN)
51
52
563
54
55
56
3
4
5
6
7
8
9
4166252
108055
S-ENGINE DECK W/LABS
BATTERY
1
1
1
1
4
4
2
1
8
4165497.7 BRACKET-RELAY MNTG
4165920 S HYD RESERVOIR W/LABS
64262-012 BLT-FLG HD 3/8-16 X 1-1/4
64197-016 BLT-TDFM 3/8-16X1/2
64163-69 WSHR .391X.88X10 GA
4164251
VALVE-OIL DRAIN
88042-03 CLAMP-HOSE 5/8
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
4143570
64141-4
STRAP-BATTERY
NUT-WLF 3/8-16
64268-03 NUT-FL NYLON LOCK 3/8-16 8
4118430
4164385
4165361
ARM-PUMP
MUFFLER-FX KAW 22-26HP
ROD-LINK ASSY
2
1
2
2
8
2
4
2
2
4
2
2
2
2
2
2
1
1
64152-46 SCREW-SLT HH 10-24X1/2
64229-02 LOCKNUT-NYLON 5/16-18
2182405.7 BRKT-REVERSE RETURN
64123-50 BLT-HEX 3/8-16X1
64141-6
64123-205 BLT-HEX 5/16-24X4
4164260
38020N
64188-02 PIN, CLEVIS 5/16X1
64168-2
64025-03 NUT-HEX 5/16-24
NUT-WLF 5/16-18
MOUNT-ANTI VIBRATION
CLEVIS YOKE, 5/16 PLATE
COTTER-HAIRPIN.08X1.19
* NOT ILLUSTRATED
2188139
4165499
4165364
* 4165365
SPRING-COMPRESSION
DAMPENER
WLDMT-MOTION CTRL LH
WLDMT-MOTION CTRL RH
30
31
32
33
34
35
36
37
38
39
64268-02 NUT-FL NYLON LOCK 5/16-18 2
48412-01
CLAMP-J
1
2
2
1
2
1
6
1
2
64229-08 LOCKNUT NYLON 5/16-24
64192-06 SETSCR SQHD 5/16-18X3/4
112386
108208
2188156
BOOT,BAT TERM POS
SWITCH DBL POLE
SWITCH-NONO DBL POLE
64197-015 BLT-TDFM 10-32X1/2 TORX
2188154 MODULE-DELAY
11060-9016 GASKET-MUFFLER
(AVAILABLE THROUGH KAWASAKI DEALER)
40
41
42
43
2308095
COVER-TERMINAL
1
4
2
4
64263-007 BLT-FLG HD M8-1.25 X 20
64266-02 NUT-FL LOCK M8-1.25
64163-55 WASHER .328X.75X14 GA
29
Download from Www.Somanuals.com. All Manuals Search And Download.
LOWER ENGINE DECK ASSY/CLUTCH
WOODS
FIGURE 2
ENGINE
PUMP
30
PUMP
9
23
36
34
35
37
1
2
1
33
11
3
25
28
27
1
16
15
1
14
2
19
5
20
14
18
3
5
BELT DETAIL
24
28
21
22
27
4
17
31
8
13
32
6
7
10
12
26
29
30
Download from Www.Somanuals.com. All Manuals Search And Download.
LOWER ENGINE DECK ASSY/CLUTCH
WOODS
FIGURE 2
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
4158360
PULLEY-PUMP
2
4
2
1
1
1
1
1
1
2
4
1
64044-18 SCREW-SET 1/4-20 X 5/16
64238-03 KEY-MET 5MM SQX28MM
64164-12 KEY
4165509
4165689
4165570.7 WLDMT-CLUTCH STOP
4121540 PIN-CLUTCH
64006-03 LOCKWSHR-3/8 HELICAL
64123-54 BLT-HEX 5/16-18X3/4
64123-70 BLT-HEX 3/8-16X1-1/2
64006-06 LCKWSHER-HELICAL 7/16
PULLEY- 5.25 OD X 1.126
CLUTCH-ELECTRIC, 225
9
10
11
12
13
14
15
64268-02 NUT-FL NYLON LCK 5/16-18 2
2308000
4128923
PULLEY-IDLER 4.00 EOD
S-ASSY-IDLER ARM PUMP
1
1
(INCLUDES ITEMS 16, 18 & 24)
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
4127999 SEAL
1
64270-01 BOLT-MET HEX M10-1.5X30 1
4128004 BEARING
33148-01 SPACER-0.379X0.750X0.25 1
2188131 SPRING-EXTENSION
64006-03 WSHR, 3/8 HELICAL LOCK 1
64123-21 BLT-HEX 3/8-24X1-1/4
4166252 S-ENGINE DECK W/LABS
64144-40 SNAP RING
1
1
1
1
1
1
1
2
4157920
BELT PUMP DRIVE
64123-216 BLT-HEX 7/16-20X2-1/4
64205-013 BLT-MET M6-1X12
64209-09 WASHER-CONICAL SPRING 2
2720949
64123-15 BLT-HEX 3/8-16X3/4
4128002 END CAP
ASSY-CLUTCH WIRE
1
1
1
38304-03 BEARING-FLNGD PLASTIC 1
64006-03 LOCKWSHR-3/8 HELICAL
4165983.7 WLDMT-BELT GUIDE
4165980.7 PLATE-CLAMPING
64268-01 NUT-FL NYLON LCK 1/4-20
64262-003 BLT-FLG HD 1/4-20 X 1
4
2
2
8
8
31
Download from Www.Somanuals.com. All Manuals Search And Download.
BUMPER
WOODS
FIGURE 3
6
1
5
4
6
2
6
6
4
5
6
3
5
5
32
Download from Www.Somanuals.com. All Manuals Search And Download.
BUMPER
WOODS
FIGURE 3
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
4166252
S-ENG DECK W/LABS
1
1
1
2
4166250.7 BRKT-BUMPER, TOP
4165490.7 WRAPPER-BUMPER
4165492.7 STRAP-BUMPER
64262-012 BLT-FLG HD 3/8-16 X 1-1/4
64268-03
12
NUT-FL NYLON LOCK 3/8-16 12
33
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL TANKS/CONTROL PANEL
WOODS
FIGURE 4
27
14
29
12
25
24
8
8
3
31
32
31
32
9
9
10
7
30
9
13
11
16
16
5
16
33
15
26
23
22
TO
ENGINE
1
9
33
19
2
9
20
15
9
20
TO ENGINE
4
21
18
17
18
17
6
34
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL TANKS/CONTROL PANEL
WOODS
FIGURE 4
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
4165428-1
TANK-FUEL LH
1
(INCLUDES ITEMS 15, 31-33, 35, 36)
2
4165429-1
TANK-FUEL RH
1
(INCLUDES ITEMS15, 31-33, 35, 36)
3
4
5
6
7
8
9
4165930
4166252
4165291
64123-50
2188178
64262-001
88042N
S-CONTROL PANEL
S ENG DECK W/LABS
CAP-FUEL, RATCHET TYPE 2
BLT-HEX 3/8-16X1
SWITCH-RETAINER
BLT-FLG HD 1/4-20 X 1/2
HOSE CLAMP
1
1
8
1
4
12
1
10 128010
KEY-SWITCH
11 118020-16
12 2721505
13 64025-15
14 64152-46
15 4132325
CONTROL-THROTTLE 48.0 1
SWITCH-PTO
1
2
2
2
3
8
8
1
2
NUT-HEX #10-24 KEPS
SCR.-SLT HH #10-24X1/2
GROMMET-FUEL TANK
16 4162977-020 HOSE,.25IDX.50OD
17 64006-03
18 64163-31
19 2188161
20 4162977-001 HOSE,.25IDX.50OD X
21 4142266
22 4162989-001 HOSE, FUEL LINE
LOCKWSHR-3/8 HELICAL
WSHR 25/64X1X12
VALVE-TANK SELECTOR
CONNECTOR, 12V RECEPT 1
1
23 4165864
24 128010-01
25 128010-03
26 88042-01
27 108009-03
28* 64025-04
29 4165120
30 4165863
31 4165763
32 4165387
33 4165667
34* 970391
FTTNG-HOSE 1/4" TO 3/16" 1
S-KEY SWITCH NYLON NUT 1
S-COVERED KEY
CLAMP
1
2
1
1
1
1
2
2
2
1
2
2
CONTROL-CHOKE 51"
NUT-3/8-24 HEX (CHOKE)
METER-HOUR
TEE-FITING 1/4" HOSE
ROLL-OVER VENT
GROMMET-ROLL OVER
FITTING-BARBED 90 DEG
KIT-LIGHTACCESSORY
FUEL-LINE TANK
35* 4165692-01
36* 4165668
FILTER-FUEL
*NOT ILLUSTRATED
35
Download from Www.Somanuals.com. All Manuals Search And Download.
BRAKES/REAR WHEEL
WOODS
FIGURE 5
15
13
20
17
4
2
7
14
16
8
27
28
6
23
11
24
19
1
9
25
12
27
30
27
10
18
17
3
19
5
21
22
27
TORQUE TO
225 FT/LBS
26
32
29
31
36
Download from Www.Somanuals.com. All Manuals Search And Download.
BRAKES/REAR WHEEL
WOODS
FIGURE 5
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
4166252
4165701.7
4165700.7
128102
4165449.7
4159701
2182387.7
38020N
S-ENGINE DECK W/LABS
WLDMT-BRAKE ARM LH
WLDMT-BRAKE ARM RH
SPRING,EXTENSION
WLDMT-BRAKE LEVER
ROD-BRAKE CONTROL
GUIDE-SPRING
1
1
1
2
1
2
2
2
2
CLEVIS YOKE, 5/16 PLATE
BRAKE-PARKER
4159281
9A* 4159281-001 BRAKE-BACK PLATE W/ PADS 1
9B* 4159281-002 BRAKE-DRUM
9C* 4159281-003 BRAKE-SCREW
9D* 4159281-004 BRAKE-HUB
9E* 4159281-005 STUD-BRAKE
1
4
1
4
10 64163-06
11 4159000
12 4159280
WSHR,.768/.756X1.25X14 A/R
BAR-PARKING BRAKE
MOTOR-PARKER
1
2
(INCLUDES ITEMS 32)
13 4165553
WHEEL-ASSY, 24X12.00-12 2
4165553-01 RIM-8 SPOKE 4 HOLE W/VALV
1985085-02 TIRE 24X12.00-12NHS 4PLY
4158422-02 TIRE 24X12-12 OTR FTLT
(ITEM 13 USED ON 61" DECKS ONLY)
14 64163-89
WSHR- 1.25ODX.76IDX18GA1
15 64187-03
16 64188-02
17 64061-25
18 2188155
19 2183063-01 SPACER, 32MM LONG
20 4165552
WHEEL NUT-1/2-20
PIN, CLEVIS 5/16X1
ROLL PIN-1/4X1-1/4
GRIP, 1/4X1X4-1/2
8
2
2
1
8
WHEEL-ASSY, 23X10.50-12 2
4165552-01 RIM-8 SPOKE 4 HOLE W/VALV
4158421-02 TIRE-23 X 10.5-12 4P TURF
4158421-03 TIRE 23X10.5-12 OTR GMSTR
(ITEM 20 USED ON 52" DECKS ONLY)
21 85010N
ZERK, 1/4-28 STR SLFTHRD 1
SNAP RING.50
BEARING-.75ID SELF ALIGN 2
22 64144-34
23 2188145
24 64123-15
25 64268-03
26 64237-06
27 64168-2
28 64025-03
29 64025-31
30 4159242
31 450767
1
BOLT-3/8-16X3/4 HEX
NUT-FL NYLN LCK 3/8-16
4
4
LOCKNUT-NYLON M12-1.75 8
COTTER-HAIRPIN.08X1.19
NUT-HEX 5/16-24
4
2
NUT 1-20 UNSLOTTED TRW 2
WLDMT-PRK BRAKE ROD
CAPSCREW 12-1.75X110
1
8
32 64164-08
S-KEY FOR WHEEL MOTOR 2
*NOT ILLUSTRATED
37
Download from Www.Somanuals.com. All Manuals Search And Download.
OIL COOLER
WOODS
FIGURE 6
3
20
10
19
15
2
10
16
18
17
8
6
8
15
15
18
4
9
5
7A
9
9
7B
9
TO PUMP CASE DRAIN
12
13
11
14
11
15
14
15
14
13
14
14
1
38
Download from Www.Somanuals.com. All Manuals Search And Download.
OIL COOLER
WOODS
FIGURE 6
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
4166252
S ENGINE DECK W/LABS
1
1
4
1
1
1
4166418.7 BRKT-COOLER FRONT
64262-002 BLT-FLG HD 1/4-20 X 3/4
2720891.7 SCREEN-OIL COOLER
2188173
4165920
COOLER-OIL
S HYD RSRVR W/LABS
(69053-05 IS A SERVICEABLE LENGTH OF 55")
7A
7B
69053-05 3/8 HIGH TEMP HOSE
69053-05 3/8 HIGH TEMP HOSE
1
1
8
9
48412-01 CABLE-CLIP N
88042-04 CLAMP-3/4 CLIP
64163-03 WSHR .256X.62X18GA
4165492.7 ARM-BUMPER
64229-01 NUT-NYLON LOCK 1/4-20
4166419.7 BRKT-REAR COOLER
2
4
2
2
4
2
10
11
12
13
14
15
16
17
18
19
20
64268-03 NUT-FL NYLON LOCK 3/8-16 8
64262-012 BLT-FLG HD 3/8-16 X 1-1/4
8
1
1
2
1
1
4165752
4165751
CLAMP-HOSE, 5/8IN
CLAMP-HOSE, 1/2IN
64229-01 NUT-NYLON LOCK 1/4-20
64123-07 BLT-HEX 1/4-20X1-1/2
64123-60 BLT-HEX 1/4-20X2
39
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR COOLED HYDRAULICS
WOODS
FIGURE 7
3
2
1
7
21
23
13
13
16
7
23
13
4
13
13
21
21
13
7
12
13
21
5
22
6
7
11
18
17
21
21
23
11
19
14
17
13
15
5
9
6
14
20
8
6
10
6
10
6
40
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR COOLED HYDRAULICS
WOODS
FIGURE 7
ITEM PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
4165920
2720396
4165236
4160243
S HYD RESERVOIR W/LAB
FILTER 25 MICRON
CAP-RESERVOIR
1
1
1
1
2
4
SAE PORT 'O' RING
THREAD SIZE
PART
NUMBER
AS-568#
PLUG-HYDRAULIC TANK
158058-04 FTG-90 BRB 9/16-18X.38
108205-03 ELBOW-MALE 45 37-ORB
158061-10
158061-11
158061-12
158061-13
158061-14
158061-16
158061-03
9/16-18
3/4-16
-906
-908
-910
-912
-916
-920
-924
7
8
69053-05
3/8 HIGH TEMP HSE
4
7/8-14
(69053-05 IS A SERVICEABLE LENGTH OF 55")
1-1/16-12
1-5/16-12
1-5/8-12
1-7/8-12
LH PUMP PORT A-HOSE
22HP 2188157-02
26HP 2188157-02
1
1
9
LH PUMP PORT B-HOSE
22HP 2188157-01
26HP 2188157-01
1
1
10 4159280
MOTOR-PARKER
2
11 2690030-02FTG 9/16-18 ORB X 3/8
2
12 58026-01
13 88042-04
14 4164841
3 WAY CONNECTOR 3/8
CLAMP-HOSE 5/8
PUMP-HYDRO 12cc
2
14
2
15 RH PUMP PORT A-HOSE
22HP 2720320-01
1
1
26HP 2720320-01
16 2188173
17 48089-03
OIL COOLER
1
FTG-STRGHT 8 ORB X 8 JIC
22HP- QTY 1 RH PUMP PORT A
26HP- QTY 2 RH PUMP PORT A & B
18 RH PUMP PORT B-HOSE
22HP 2188157-01
26HP 2720320-02
19 64123-60
20 64229-01
21 88042-05
22 58026-04
BOLT, 1/4-20X2 HEX
LOCKNUT-NYL 1/4-20
CLAMP-HOSE 13/16
3 WAY CONNECTOR 3/16
2
2
6
1
2
23 4165341-02 HOSE-HYDR,
41
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDROGEAR PUMP
WOODS
FIGURE 8
22
20
21
18
1
3
49
32
34
30
29
15
38
37
25
42B
2
5
57
42A
44
8
7
4
56
6
10
42
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDROGEAR PUMP
WOODS
FIGURE 8
ITEM HYDROGEAR PART NO. WOODS PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
70516
72011
50641
50969
52629
71246
50273
9004101-1340
9007200-3116
2513030
70522
51161
50951
-----
4164841-001
-----
HOUSING KIT
END CAP KIT
1
1
2
4
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
STRAIGHT HEADLESS PIN
FLANGE BOLT M8-1.25 X 60
HOUSING O-RING
CHARGE PUMP KIT
STD GEROTOR ASSEMBLY
O-RING
SOCKET SCREW M6-1.0 x 20
BYPASS VALVE KIT (BLANK)
PUMP SHAFT KIT
LIP SEAL 17 x 40 x 12
SPACER
RETAINING RING
CYLINDER BLOCK KIT
BLOCK SPRING
BLOCK THRUST WASHER
SWASH PLATE
BALL THRUST BEARING
ARM-TRUNION
2721615-01
4164841-002
4137278-01
38345-07
38345-08
64123-68
4157242-019
4137278-05
-----
-----
-----
4164841-003
-----
-----
188059-11
4164841-004
188059-15
2721615-13
4121354
4121355
4137278-07
2721615-17
-----
10
15
18
20
21
22
25
29
30
32
34
37
38
42A
42B
44
49
56
57
100
50329
71971
2003014
2003017
2003087
53502
2003005
2000015
70743
70741
70402
2513043
9005110-4400
9005110-5600
70525
SLOT GUIDE
SHOCK VALVE KIT (.031")
SHOCK VALVE KIT (BLANK)
CHARGE RELIEF VALVE KIT
TRUNNION SEAL/RETAIN KIT
STRAIGHT THREAD PLUG
PLUG-9/16-20 STEEL
OVERHAUL SEAL KIT
4157242-025
2721615-18
43
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR COOLED WIRE HARNESS
WOODS
FIGURE 9
CLUTCH
ELECTRIC
13
WIRE COLORS
WHITE
WB WHITE W/ BLACK STRIPE
12
W
ENGINE
GROUND
STARTER
P
O
PURPLE
ORANGE
OB ORANGE W/ BLACK STRIPE
PO PURPLE W/ ORANGE STRIPE
OP ORANGE W/ PURPLE STRIPE
DB DARK BLUE
20
BATTERY
BATTERY
B
G
R
Y
BLACK
GREEN
RED
7
3
(RED)
YELLOW
YB YELLOW W/ BLACK STRIPE
RW RED W/ WHITE STRIPE
(BLACK)
GY GREEN W/ YELLOW STRIPE
ENGINE BLOCK SOLENOID
DELAY
MODULE
BROWN
BR
(GROUND)
21
BRY BROWN W/ YELLOW STRIPE
10
TO ENGINE BLOCK
(GROUND)
CARB
SOLENOID
MAGNETO
PACKARD
#02962793
VOLTAGE
19
REGULATOR
TO SOLENOID (4)
W
G
P
P
9
9
9
17
BLADES &
TRACTION
RELAY
21
18
(RED)
Y
TO SOLENOID (3)
21
DELAY
RELAY
TO SOLENOID (2)
24
STARTER
RELAY
23
SOFT START HARNESS
SOFT START MODULE
87A NC
87 NO
86
30
85
15
SWITCH
BRAKE
RELAY SCHEMATIC
5
14
TRACTION
CONTROL
SEAT
SWITCH
22
12V
ADAPTER
4
TRACTION
CONTROL
14
11
AUXILIARY
ELECTRICAL
CONNECTION
CLUTCH
SWITCH
KEY
SWITCH
HOUR
METER
6
8
44
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR COOLED WIRE HARNESS
WOODS
FIGURE 9
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
4163532
148082-20 FUSE-20 AMP
108061-13 CABLE-BATTERY 36 BLACK 1
4124009
4143068
4165120
HARNESS-WIRING MAIN
1
2
SWITCH-SEAT, NO
JUMPER-SEAT SWITCH
METER-HOUR
1
1
1
1
2722227-02CABLE-BATT W/CONDUIT
(INCLUDES ITEMS 20 & 21)
2722227-01CABLE-BATT W/CONDUIT
(USED ON 22HP ONLY - INCLUDES
ITEMS 20 & 21)
1
8
9
10
11
12
128010
KEY-SWITCH
1
3
1
1
1
2722325
2188154
2721505
2721337
RELAY-40AMP SEALED
MODULE-DELAY
SWITCH-PTO
CLUTCH-ELECTRIC
(INCLUDES 2720949 WIRE ASSY)
13
14
15
16*
2720949
108208
2188156
38665
ASSY-CLUTCH WIRE
SWITCH-DBL POLE
SWITCH-NONO DBL POLE
SOLENOID
1
2
1
1
(USED ON 22HP ONLY)
17
18
2188224
(USED ON 22HP ONLY)
HARNESS-JUMPER
1
1
108061-04 CABLE-BATTERY 20 RED
(USED ON 22HP ONLY)
19
20
21
22
2188225
112386
2308095
4142266
WIRE-GROUND
1
1
3
1
BOOT-BAT TERM POS
COVER-TERMINAL
CONNECTOR-12V
ITEMS 23-24 USED ON 72" DECK ONLY
23
24
4165894
4165923
MODULE-SOFT START
HARNESS-SOFT START
1
1
*NOT ILLUSTRATED
45
Download from Www.Somanuals.com. All Manuals Search And Download.
SEAT ASSEMBLY
WOODS
FIGURE 10
5
1
6
2
7
3
21
8
4
9
11
12
16
13
10
19
14
17
18
BRACKET ON
ENGINE DECK
WELDMENT
15
46
Download from Www.Somanuals.com. All Manuals Search And Download.
SEAT ASSEMBLY
WOODS
FIGURE 10
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
4166226
SEAT-SUSPENSION
1
(INCLUDES ITEMS 2-12, 21)
2
3
4
5
6
7
8
9
4166226-05 UPPER SEAT ASSEMBLY
4166226-04 CUSHION-COVER BACK
4166226-01 CUSHION COVER
4166226-06 PROTECTOR-BACK
4165316-02 PAD-ARM SINGLE
4165316-05 ARM KIT-LH
1
1
1
1
2
1
1
1
2
1
1
1
2
2
2
4
2
2
1
1
4165316-04 ARM KIT-RH
4124009
SWITCH-SEAT NO
10 2720975-07 SPACER
11 4164679
12 4166226-03 TRACK SET
13 4165366.7
14 48228A
15 64152-23
16 2720975-09 SPACER
17 64141-6
18 64144-30
19 33138-09
20 4143068
SUSPENSION
PLTE-SEAT
CABLE CLIP-INSULATED
SCREW 1/4-20X3/8
NUT-WLF 5/16-18
SNAP RING
PIN-CLEVIS
JUMPER-SEAT SWITCH
21 4165316-03 ARM KIT-LEFT AND RIGHT
* NOT ILLUSTRATED
47
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL FOLDING ROPS KIT (970410)
WOODS
FIGURE 11
2
1
B
15
6
4
19
16
3
17
18
2
A
1
7
9
10
4
8
A
14
5
12
11
13
5
13
11
12
48
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL FOLDING ROPS KIT (970410)
WOODS
FIGURE 11
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
4162879
64123-31 BOLT-1/2-13 X 3
PIN-HITCH 1/2
2
2
2
2
1
1
2
2
2
2
16
8
8
8
2
2
2
2
2
64151-7
4162880
4166217
4160347
64163-19 WASHER-FLAT 7/16
64123-28 BOLT-7/16 X 1-1/4
64006-06 LOCKWASHER-7/16
64151-11 LOCKNUT-7/16
64163-31 WASHER-3/8
64006-03 LOCKWASHER-3/8
64123-16 BOLT-3/8-16 X 1-1/4
64025-05 NUT-3/8-16 HEX
64168-1
4160343
4160344
4160348
4162878
LOCKNUT- 1/2-13
LANYARD-NYLON
SEATBELT
LABEL-WARNING ROPS
9
10
11
12
13
14
15
16
17
18
19
PIN-COTTER
BUMPER RUBBER
PLUG
WASHER-FORMED
WASHER-RUBBER
49
Download from Www.Somanuals.com. All Manuals Search And Download.
STEERING/DECK LIFT
WOODS
FIGURE 12
44
8
5
37
6
7
16
19
27
15
9
12
48
48
9
10
13
1
3
47
2
47
46
11
15
43
38
35
23
44
22
39
33
25
21
24
29
15
42
36
21
14
17
28
15
36
31
41
32
40
4
15
30
34
21
26
18
20
51
49
50
50
Download from Www.Somanuals.com. All Manuals Search And Download.
STEERING/DECK LIFT
WOODS
FIGURE 12
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
4166252
4163746
4165962
S ENGINE DECK W/LABS
SPRING
ZERK-90 DEGREE
1
2
2
1
2
2
2
2
4
8
32
33
34
35
36
37
38
39
40
41
64221-04 E-RING .875
64175-05 NUT-PUSH 1/2
64188-36 PIN, CLEVIS 7/16X1-1/4
4165466 GRIP
2183071-03SPACER-15.88X10.32X24
1
1
2
1
2
64123-50 BLT-HEX 3/8-16X1
4165426.7 LEVER-TRACTION CNTRL
4165425.7 BRKT-TRACTION LEVER
4162998
4165432
4164260
64268-03 NUT-FL NYLON LOCK 3/8-16 4
BRKT-HANDLE
GRIP-HANDLE
MOUNT-ANTI VIBRATION
2720544
4165448
SPRING-COMPRESSION
ROD-LIFT STOP
1
1
6
9
64163-65 WSHR .890X1.375X18GA
10
11
12
64123-15 BOLT-3/8-16X3/4 HEX
4165654
4165655
LBL-ZT200 HT CUT OUTER 1
LBL-ZT200 HT CUT INNER 1
64141-4
4165364
4165365
NUT-WLF 3/8-16
WLDMT-MTN CONTRL LH
WLDMT-MTN CONTRL RH
12 42
1
1
43
44
45
46
64163-29 WASHER-21/64 X 1 X 11GA 2
*
4163692
64229-02 NUT-NYLON LOCK 5/16-18
4163446 KNOB
CAP-END
3
2
2
4
4
4
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
64123-87 BLT-HEX 3/8-16X1-3/4
64123-16 BLT-HEX 3/8-16X1-1/4
64229-03 NUT-NYLON LOCK 3/8-16
64262-012 BLT-FLG HD 3/8-16 X 1-1/4
64123-100 BLT-HEX 3/8-16X2-1/4
64163-43 WSHR.443/.454X1X11GA
4165474
4165390.7 WLDMT-CRADLE
64168-2 COTTER-HAIRPIN.08X1.19
2
12 47
20 48
64163-55 WSHR .328X.75X14 GA
64163-107 WSHR-.391 X .75 X 10GA
64262-011 BLT-FLG HD 3/8-16 X 1
8
1
1
2
1
4
49
50
51
4165682
MOUNT-ISOLATION, FOOT 2
64229-03 NUT-NYLON LOCK 3/8-16
4
SPACER
4165380.7 WLDMT-DECK LIFT LEVER 1
4162904.7 WLDMT-LVR STOP LATCH
4165384.7 BRKT-INNER DECK LIFT
4165385.7 BRKT-OUTER DECK LIFT
4165389.7 BRACKET-LIFT LINK
4162999
4165656
64188-53 PIN-CLEVIS 1/2X1.0
64018-38 BOLT-CRG 3/8-16 X 2-1/4
85010N
1
1
1
2
1
1
1
1
SPACER
ASSY, PIN & LANYARD
ZERK, 1/4-28 STR SELF TH 11
51
Download from Www.Somanuals.com. All Manuals Search And Download.
CRADLE ASSEMBLY
WOODS
FIGURE 13
38
4
TO
KICKPLATE
5
1
8
7
6
5
40
24
14
6
41
42
20
30
22
39
32
29
15
27
30
44
43
27
37
30
22
23
21
13
10
9
28
12
33
3
17
26
25
19
2
28
17
25
34
10
9
16
23
21
31
36
35
28
11
13
28
3
25
25
2
28
16
52
Download from Www.Somanuals.com. All Manuals Search And Download.
CRADLE ASSEMBLY
WOODS
FIGURE 13
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
4165610
LABEL-WARNING
1
2182356.7 BRACKET-SHAFT HANGER 4
2188127
4165647
4166266
4165682
4166254
4166267
CHAIN-6.35 (.250) 5 LINKS
MAT-FOOT PLATE LOWER
MAT-FOOT PLATE UPPER
MOUNT-ISOLATOR
LABEL-WOODS
S-FOOT PLATE
4
1
2
2
1
1
(INCLUDES ITEMS 4-7)
9
64163-65 WASHER-.890X1.375X18GA 8
64221-04 E-RING.875
4165379.7 WLDMT-DECK LIFT, FRONT 1
10
11
12
13
14
15
16
17
18 *
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
4
4165427.7 WLDMT-DECK LIFT, REAR
1
2722630
4165675
CLIP-DECK HEIGHT ADJ
SPRING-DECK LIFT
4
2
4165390.7 WLDMT-CRADLE
1
64268-03 NUT-FL NYLN LCK 3/8-16
15
2
4109960
WLDMT-DECK LIFT ROD
4111842.7 BRKT-SPRING ANCHOR LH 1
4165556
4113682
64141-2
64141-4
MAT-FOOT LIFT
1
2
4
4
4
2
ROD-SPRING MOUNT
NUT-WLF 1/4-20
NUT-WLF 3/8-16
64197-020 BLT-TDFM 1/4-20X1-1/2
64123-31 BLT-HEX 1/2-13X3
64123-281 BLT-HEX 1/2-13X2 FL THRD 8
4165596.7 BRKT-FOOT, LIFT LEVER
64262-011 BLT-FLG HD 3/8-16 X 1
64141-13 NUT WLF 1/2-13
1
15
16
85010N
85051
ZERK, 1/4-28 STR SLFTHRD 1
ZERK-1/8 PIPE
6
1
2
1
1
2
2
2
2
2
1
2
2
6
4
64229-03 NUT-NYLON LOCK 3/8-16
64018-3 BLT-CRG 3/8-16X1
4165593.7 WLDMT-FOOT PEDAL
64123-100 BLT-HEX 3/8-16X2-1/4
64123-67 BLT-HEX 3/8-16X2
64001-6
64229-05 NUT-NYLON LOCK 3/8
64018-2 BLT-CRG 1/4-20X3/4
64268-01 NUT-FL NYLON LCK 1/4-20
4160281 DOCUMENT TUBE
64262-006 BLT-FLG HE 5/16-18X3/4
4165676 BUMPER-RADIAL
64268-02 NUT-FL NYLN LCK 5/16-18
4164210 BUMPER-RUBBER
NUT-HEX JAM 3/8-16
*NOT ILLUSTRATED
53
Download from Www.Somanuals.com. All Manuals Search And Download.
CRADLE & CASTER ASSEMBLY
WOODS
FIGURE 14
23
14
22
10
15
19
13
8
1
20
12
8
15
18
13
5
21
17
11
17
16
4
6
16
17
3
9
7
17
7
9
2
54
Download from Www.Somanuals.com. All Manuals Search And Download.
CRADLE & CASTER ASSEMBLY
WOODS
FIGURE 14
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
2
48043-03C CUP, OUTER BEARING
4165278 ASSY-WHL 13X6.5-6
(INCLUDES ITEM 7)
DECK/W LABS
4
2
3
4
5
6
7
8
9
10
11
12
13
64123-223 BOLT-3/4-10 X 10
2722452.7 WLDMT-CASTER YOKE
2722230-03 SPANNER
2722228-03BEARING
64229-03 NUT-NYLON LOCK 3/8-16
2
2
2
2
8
4
2
2
2722231
SPACER-END
64163-26 WASHER
64229-07 LOCKNUT-NYLON 3/4-10
85010N
ZERK, 1/4-28 STR SLF THD 2
64123-16 BLT-HEX 3/8-16X1-1/4
8
14
15
16
17
18
19
20
2188135
DUST COVER
2
4
8
16
2
48043-04C CONE, OUTER BEARING
64123-281 BLT-HEX 1/2-13X2 FLLTHD
64141-13 NUT WLF 1/2-13
48480
64140-5
SEAL CR 12411
COTTER PIN
2
1
4165326.7 WLDMT-CSTR ARM 52 LH
(USED WITH 52" DECKS)
4165327.7 WLDMT-CSTR ARM 61 LH
(USED WITH 61" DECKS)
21
4165323.7 WLDMT-CSTR ARM 52 RH
(USED WITH 52" DECKS)
1
4165324.7 WLDMT-CSTER ARM 61 RH
(USED WITH 61" DECKS)
22
23
64025-20 NUT-HEX 3/4-16 SLOT U
4165390.7 WLDMT-CRADLE
2
1
55
Download from Www.Somanuals.com. All Manuals Search And Download.
52" SIDE DISCHARGE
WOODS
FIGURE 15
30
29
40
21
22
11
14
57
58
43
27
55
23
17
41
44
33
6
51
47
15
52
61
54
66
57
59
60
62
23
62
18
19
31
19
4
3
31
34
33
45
10
69
70
32
38
31
35
28
56 26
8
13
36
7
9
35
7
9
7
7
8
2
5
13
7
74
4
35
16
20
70
41
35
46
70
65
53
46
73
12
75
37
5
53
48
68
72
42
21
39
35
48
71
46
43
TORQUE TO
70 FT-LBS
68
67
48
53
56
Download from Www.Somanuals.com. All Manuals Search And Download.
52" SIDE DISCHARGE
WOODS
FIGURE 15
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
4166259
4165608.7 COVER-BELT RH
4165609.7 COVER-BELT LH
38524
4166097
548138
64229-03 NUT-NYLON LOCK 3/8-16
64123-173 BLT-HEX 3/8-16X4-1/2
2721512
64123-68 BLT-HEX 5/16-18X1
4165646
112111-02 BLADE 18.00 OFFST HLFT
2720685
64262-012 BLT-FLG HD 3/8-16 X 1-1/4 18
4165754.7 WLDMT-IDLER ARM
64018-11 BLT-CRG 1/2-13X3LG
4163514.7 GUIDE, BELT
S-DECK W/ LABELS 52" ZT2 1
48
49
1
64229-01 NUT-NYLON LOCK 1/4-20
4165966.7 BAFFLE-FRONT,CENTER 52IN
1
1
1
KNOB-4 PRONG 3/8-16
2
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
4165965.7 BAFFLE-FRONT,LH 52IN
1
1
1
CHUTE-RUBBER ASSY
BRG NDL.88 1.12 1.00
1
1
521438
4163014
GREASE SEAL
SPACER
28
3
64268-03 NUT-FL NYLON LOCK 3/8-16 5
4163155
INNER RING
1
1
2
9
ROLLER-5X2.75 CENTERED 6
64144-40 SNAP RING-2NTERNL
64018-23 BLT-CRG 3/8-16X3/4 SHRT
38348-01 BEARING-SPINDLE SEALED6
4164948 HOUSING-SPINDLE 6 HOLE 3
64144-38 RING-SNAP
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
2
3
3
6
PULLEY-5.25 DEEP GRVE
SPACER-ROLLER
3
3
3
38315
NUT-SPINDLE
1
2
1
1
2
1
6
3
2
4144947
PULLEY SPINDLE 36-52
64268-05 NUT-FL NYLON LOCK 1/2-13 2
64018-30 BLT-CRG 3/8-16 X 4-1/2
64262-013 BLT-FLG HD 3/8-16 X 1-1/2
4165252.7 HINGE-CHUTE_RUBBER
4165484.7 WLDMT-IDLER PIN
4165870.7 BRKT-BAFFLE MOUNTING
4165955.7 BRKT-BAFFLE MNTG
64123-171 BLT-HEX 3/8-16X3-1/2
3
2
1
1
1
2
2
4
1
1
7
7
4165953
PULLEY-IDLER, 6.0
4163802-01SPACER-2.0 X .515 X .75
4165976.7 BAFFLE-DISCHARGE
64209-03 SPRING WASHER.67 ID
64164-12 KEY-1/4X1 SQ
128169
4165023
4165755
PULLEY IDLER 5.50
ASSY-CTTERDECK SPNDL 3
64141-4
NUT-WLF 3/8-16
ASSY-IDLER ARM 48-52
1
4163438.2 EXTENSION-52" RH
4163439.2 EXTENSION-52" LH
(INCLUDES ITEMS 6, 15, 33, 41,51 & 55)
64141-2
NUT-WLF 1/4-20
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
90-0828 S/B BOLT 1/2-13X3 1/2 NC
1
1
2
1
1
3
2
64123-114 BLT-1/4-20X1
64270-02 BLT-HEX M10-1.5x30 ISO
4133155.7 WLDMT-PUSH ARM ZT2
64006-05 LOCKWSHR-1/2 HELICAL
64123-156 BLT-HEX 1/2-20X1-3/4
64163-74 WSHR-.516X2.00X.25 PLT
2186125
85010N
64123-152 BLT-HEX 5/8-11X5
64123-50 BLT-HEX 3/8-16X1
64229-02 NUT-NYLON LOCK 5/16-18
4118314
64229-06 NUT-NYLON LOCK 5/8-11
64123-187 BLT-HEX 5/8-18 X 3 3/4
64123-208 BLT-HEX 5/8-18X1-1/2
* NOT ILLUSTRATED
WLDMT-LOCK PUSHBAR
ZERK 1/4-28 STR SLF THRD 5
2
9
2
3
2
3
3
SPACER-BLADE 16MM
4128004
BEARING-BALL 10 X 26 X 8 1
4165967.7 BAFFLE-FRONT,RH 52IN
4128002
4165943
64163-93 WSHR-.635 X 1.12 X.062
64018-2
64018-7
1
1
1
2
4
3
CAP-26 X 7 END
SPRING-EXTENSION
BLT-CRG 1/4-20X3/4
BLT-CRG 3/8-16X1-1/4
57
Download from Www.Somanuals.com. All Manuals Search And Download.
61" SIDE DISCHARGE
WOODS
FIGURE 16
40
21
22
30
29
23
43
27
11
6
55
41
17
44
15
33
14
57
73
47
58
51
52
24
54
61
66
62
57
59
23
62
18
60
19
31
19
31
74
35
3
34
4
74
75
45
33
38
56
35
35
28
75
31
33
32
10
1
63
7
26
36
9
13
7
9
7
8
7
70
2
35
75
13
4
70
67
16
75
53
68
69
7
69
20
65
53
50
46
46
12
5
37
21
48
46
72
46
39
53
49
64
48
72
42
48
53
71
53
48
58
Download from Www.Somanuals.com. All Manuals Search And Download.
61" SIDE DISCHARGE
WOODS
FIGURE 16
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
4166255
S-DECK W/ LABELS 61" ZT2 1
44 4165943
45 64163-93
46 64018-2
47 64018-7
48 64229-01
SPRING-EXTENSION
WSHR-.635 X 1.12 X.062
BLT-CRG 1/4-20X3/4
BLT-CRG 3/8-16X1-1/4
NUT-NYLON LOCK 1/4-20
1
4
7
3
7
2
3
4
5
6
7
8
9
4165456.7 BELT COVER-RH 1
4165455.7 BELT COVER-LH
38524
4166097
64163-68
64229-03
64123-173 BLT-HEX 3/8-16X4-1/2
2721512
1
KNOB-4 PRONG 3/8-16
CHUTE-RUBBER ASSY
WSHR-1.015X1.5X9GA
NUT-NYLON LOCK 3/8-16
2
1
6
34
3
49 4165969.7 BAFFLE-FRONT,CNTR 61IN 1
50 4165968.7 BAFFLE-FRONT,LH 61IN
1
1
1
4
1
1
2
6
51 521438
52 4163014
53 64268-03
54 4163155
55 64144-40
56 64018-23
57 38348-01
58 4164948
59 64144-38
60 38315
GREASE SEAL
SPACER
ROLLER-5X2.75 CENTERED 7
10 64123-68
11 4130120
(USED ON GENERAC MODELS ONLY)
2308140 PULLEY-ENGINE
(USED ON KAWASAKI MODELS ONLY)
BLT-HEX 5/16-18X1
2
NUT-FL NYLN LCK 3/8-16
INNER RING
SNAP RING-26MM INTENA
BLT-CRG 3/8-16X3/4
BEARING-SPINDLE SEALD
HOUSING-SPINDLE 6 HOLE 3
RING-SNAP
NUT-SPINDLE
PULLEY-7.0 B GRV 1.0 BORE 3
12 112111-03
13 2720685
14 64262-012 BLT-FLG HD 3/8-16 X 1-1/4 18
BLADE 21.00 OFFST HLFT
SPACER-ROLLER
3
7
3
3
3
61 2183070-02 SHAFT-SPINDLE
15 4165754.7 WLDMT-IDLER ARM
16 64018-11 BLT-CRG 1/2-13X3LG
17 4163514.7 GUIDE, BELT
1
1
1
1
2
1
6
3
2
62 64268-05
63 64018-30
NUT-FL NYLON LOCK 1/2-13 2
BLT-CRG 3/8-16 X 4-1/2
4
2
1
1
1
1
7
7
1
2
1
2
4
1
64 64262-013 BLT-FLG HD 3/8-16 X 1-1/2
65 4165252.7 HINGE-RUBBER CHUTE
66 4165484.7 WLDMT-IDLER PIN
67 4163440.7 EXTENSION-61"RH
68 4163441.7 EXTENSION-61"LH
69 64141-2
70 64123-114 BLT-HEX 1/4-20X1
71 4165871.7 BRKT-BAFFLE MNYNG, RH
72 4165955.7 BRKT-BAFFLE MNTG
73 548138
18 4165953
PULLEY-IDLER, 6.0
19 4163802-01 SPACER-1.0 X .516 X .75
20 4165976.7 BAFFLE-DISCHARGE
21 64209-03
22 64164-12
23 128169
24 4165023
25 4165755
SPRING WASHER.67 ID
KEY-1/4X1 SQ
PULLEY IDLER 5.50
ASSY-CTTERDCK SPINDLE 3
ASSY-IDLER ARM
NUT-WLF 1/4-20
1
(INCLUDES ITEMS 15, 33, 41, 51, 55, & 73)
BRG NDL.88 1.12 1
74 64123-171 BLT-HEX 3/8-16X3-1/2
75 64141-4
76 64163-55
26 90-0828
27 64270-02
S/B BOLT 1/2-13X3 1/2 NC
BLT-HX M10-1.5x30 ISO
1
1
2
1
1
3
2
NUT-WLF 3/8-16
WSHR .328X.75X14 GA
28 4133155.7 WLDMT-PUSH ARM ZT2
29 64006-05 LOCKWSHR-1/2 HELICAL
30 64123-156 BLT-HEX 1/2-20X1-3/4
31 64163-74
32 2186125
33 85010N
WSHR-.516IX2.00OX.250
WLDMT-LOCK PUSHBAR
ZERK 1/4-28 STR SLF THRD 5
34 64123-152 BLT-HEX 5/8-11X5
2
8
2
3
2
3
3
1
1
1
35 64123-50
36 64229-02
37 4118314
38 64229-06
BLT-HEX 3/8-16X1
NUT-NYLON LOCK 5/16-18
SPACER-BLADE 16MM
NUT-NYLON LOCK 5/8-11
39 64123-187 BLT-HEX 5/8-18 X 3 3/4
40 64123-208 BLT-HEX 5/8-18X1-1/2
41 4128004
42 4165970.7 BAFFLE-FRONT,RH 61IN
43 4128002 CAP-26 X 7 END
BEARING-BALL 10 X 26 X 8
59
Download from Www.Somanuals.com. All Manuals Search And Download.
BELTS-CUTTERDECK
WOODS
FIGURE 18
1
60
Download from Www.Somanuals.com. All Manuals Search And Download.
BELTS-CUTTERDECK
WOODS
FIGURE 18
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
4165619
4165618
BELT-CUTTERDECK 52"
BELT-CUTTERDECK 61"
1
61
Download from Www.Somanuals.com. All Manuals Search And Download.
DECALS-POWER UNIT
WOODS
FIGURE19
BACK OF
ENGINE DECK
8
3
DOCUMENT
TUBE
LOCATED UNDER FOOTPLATE
5
4
UNDER SEAT
15
LOCATED BEHIND
SEAT ON OIL COOLER
11
7
6
10
16
9
LOCATED UNDER
FOOTPLATE
2
12
17
14
13
1
62
Download from Www.Somanuals.com. All Manuals Search And Download.
DECALS-POWER UNIT
WOODS
FIGURE 19
ITEM PART NO.
DESCRIPTION
LABEL-MZ
LABELFOOTPLATE WOODS 1
LABEL-OPER MAN
LABEL, WARN BATTERY
LABEL - HYDR OIL FILL
LABEL-CONTROL PANEL
LABEL - PARK BRAKE
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
4139941
4166254
2000735
2000590
4165722
4165639
2000693
2000698
4165653
4165615
4165616
4165654
4165655
4165610
4147617
4164839
4164838
1
2
3
4
5
6
7
8
9
1
1
1
1
1
LABEL(DBL) - FUEL/LEAKS 2
LABEL-ZT INFORMATION
LABEL - RH TRACTION
LABEL - LH TRACTION
LABEL-HT CUT OUTER
LABEL-HT CUT INNER
LABEL-WARNING
LABEL-FUEL
LABEL-WOODS MZ2252K
LABEL-WOODS MZ2661K
1
1
1
1
1
1
1
1
10
11
12
13
14
15
16
17
4116761
LABEL-MADE IN U.S.A
1
*NOT ILLUSTRATED
63
Download from Www.Somanuals.com. All Manuals Search And Download.
DECALS-CUTTERDECKS
WOODS
FIGURE 20
1
64
Download from Www.Somanuals.com. All Manuals Search And Download.
DECALS-CUTTERDECKS
WOODS
FIGURE 20
ITEM PART NO.
DESCRIPTION
QTY
ITEM PART NO.
DESCRIPTION
QTY
1
2
4164269
2000577
LABEL-WARNING BLADES
LABEL-WARNING
1
2
65
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
(Mow’n Machine Zero-Turn Mowers and Woods Boundary Utility Vehicles)
TM
TM
Please Enter Information Below and Save For Future Reference.
Date Purchased: __________________________
Model Number: __________________________
From (Dealer):______________________________________
Serial Number: _____________________________________
WHAT IS COVERED:
TM
TM
Woods Equipment Company (“WOODS”) warrants Mow’n Machine zero-turn mowers and attachments and Woods Boundary utility
vehicles, accessories and attachments to be free from defect in material and workmanship for the warranty periods listed below.
FOR HOW LONG:
Mow’n Machine Model #CZ1736K, CZ1948K, CZ1952K, CZ2361, ME1952K, ME2661B, MZ2552K, MZ2561K, MZ2761, MZ3761K,
MZ3772K, MZ2661KL & attachments are warranted for two (2) years from the date of delivery to the original purchaser or 2000 hours of
operation, whichever occurs first. Purchaser may opt for a warranty of five (5) years from the date of delivery to the original purchaser or 500
hours of operation, whichever occurs first. The dealer must specify the special warranty term on the original, dated bill of sale and a copy must
be provided with all warranty claims. Mow’n Machine model numbers CZR2242B and CZR2652B are warranted for residential use for three (3)
years from the date of delivery to the original purchaser or for commercial use for 90 days from the date of delivery to the original purchaser..
Mow’n Machine Model #FE21B, FZ21D, FZ23B, FZ25D, FZ28K & attachments are warranted for two (2) years from the date of delivery to the
original purchaser or 2000 hours of operation, whichever occurs first.
In addition, Mow’n Machine ME and MZ Series Models, serial number XXXXXXXX300 and above, have a Limited Lifetime Warranty on deck,
deck cradle, and engine deck for the life of the machine to the original retail purchaser.
Woods Boundary utility vehicle Model #MAV350, MAV480, MAV4x4, accessories & attachments are warranted for two (2) years from the date
of delivery to the original purchaser.
IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION
TO THE DURATION OF THE WRITTEN WARRANTY PERIODS LISTED ABOVE. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you.
WHO IS COVERED:
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer the product to a
third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WHAT IS NOT COVERED:
This Warranty does not cover normal wear or tear, or normal maintenance items, or any damage, failure or loss caused by:
1. Improper operation, improper maintenance, misuse, or an accident;
2. Any modification or repair by someone other than WOODS, a WOODS’ authorized dealer or distributor, and/or a WOODS’
authorized service center; or
3. Repairs made with parts other than those obtained through WOODS.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories with respect to which the
manufacturer provides a separate warranty.
WHAT WOODS WILL DO TO CORRECT PROBLEMS:
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if the product
is defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30) days
after such defect or noncompliance is discovered or should have been discovered, routed through the dealer and distributor from whom the
purchase was made, transportation charges prepaid. WOODS shall complete such repair or replacement within a reasonable time after WOODS
receives the product.
OTHER LIMITATIONS:
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the foregoing, WOODS shall not be liable for any damages relating to (i) lost profits, business, revenues or goodwill;
(ii) any expense or loss incurred for labor, supplies, substitute machinery or rental; or (iii) any other type of damage to property or economic loss.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company, including without limitation, WOODS, its
authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty.
HOW STATE LAW APPLIES:
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
QUESTIONS:
Answers to any questions regarding warranty service and locations may be obtained by contacting:
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
800-319-6637 tel
800-399-6637 fax
F-8045 MM & Boundary (Rev. 12/1/2008)
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
TM
(Mow’n Machine Zero-Turn Mower and
TM
Woods Boundary Utility Vehicle Replacement Parts)
TM
Woods Equipment Company (“WOODS”) warrants replacement parts for Mow’n Machine zero-turn
TM
mowers and attachments and Woods Boundary utility vehicles, accessories and attachments to be free
from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the
product to the original purchaser.
IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
PURPOSE ARE LIMITED IN DURATION TO A PERIOD OF NINETY (90) DAYS FROM THE
DATE OF DELIVERY OF THE PRODUCT TO THE ORIGINAL PURCHASER. Some states do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser
sell or otherwise transfer the product to a third party, this Warranty does not transfer to the third party
purchaser in any way. There are no third party beneficiaries of this Warranty.
This Warranty does not cover normal wear or tear, or normal maintenance items, or any damage, failure
or loss caused by improper operation, improper maintenance, misuse, or an accident.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement,
free of charge, of the product if the product is defective or in noncompliance with this Warranty. The
product must be returned to WOODS with proof of purchase within thirty (30) days after such
defect or noncompliance is discovered or should have been discovered, routed through the dealer
and distributor from whom the purchase was made, transportation charges prepaid. WOODS
shall complete such repair or replacement within a reasonable time after WOODS receives the product.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses,
arising directly or indirectly from the product, whether such claim is based upon breach of
contract, breach of warranty, negligence, strict liability in tort or any other legal theory. Without
limiting the foregoing, WOODS shall not be liable for any damages relating to (i) lost profits, business,
revenues or goodwill; (ii) any expense or loss incurred for labor, supplies, substitute machinery or rental;
or (iii) any other type of damage to property or economic loss. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitations may not apply to you.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is
authorized to alter, modify, or enlarge this Warranty.
This Warranty gives you specific legal rights, and you may also have other rights which may vary from
state to state.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
800-319-6637 tel
800-399-6637 fax
F-8495 MM & Boundary Repair Parts (Rev. 2/15/2006)
Download from Www.Somanuals.com. All Manuals Search And Download.
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
800-319-6637 tel
800-399-6637 fax
©2008 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and “Tested. Proven. Unbeatable.” are trademarks
of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that
appear in this manual are the property of their respective companies or mark holders. Specifications subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|