®
STOP
DO NOT RETURN TO STORE
For Missing Parts or Assembly
Questions Call 1-866-576-8388
• Safety
Before using this product, read
this manual and follow all Safety
Rules and Operating Instructions.
• Assembly
• Operation
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
FORM NO. 40258 (06/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
CARTON CONTENTS
1. Sweeper Housing Assembly
2. Hopper Bag
3. Upper Handle
4. Lower Handle Leg Stand (2)
5. Short Bag Rod
6. Long Bag Rod
HARDWARE PACKAGE
(NOT SHOWN FULL SIZE)
Ref.
No.
Description
Qty.
A
B
C
D
E
F
Hex Bolt, 1/4-20 x 1-1/4"
Flat Washers 1/4" I.D.
Hex Lock Nuts 1/4-20
Bag Rod Clips
4
4
8
4
4
2
2
2
Curved Head Bolts 1/4-20 x 1"
Palnut 1/4"
G
H
Plastic Caps (for bag rods)
Plastic Caps (for leg stands)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
3. Now tighten the four bolts from step 1.
TOOLS REQUIRED FOR ASSEMBLY
(1)Phillips Screwdriver
(1)Adjustable Wrench
4. Assemble a bag rod clip to the inside of each lower
handle tube using a curved head bolt secured down
against the clip using a 1/4" lock nut. The open end
of the clips should face towards the sweeper housing.
See figure 3.
(1) 7/16" Open End or Box Wrench
1. Assemble the two Handle Leg Stand Tubes to the
Sweeper Housing, using two hex bolts 1/4-20 x 1-
1/4" long, flat washers and 1/4-20 hex lock nuts, per
handle. See figure 1. Only hand tighten at this time.
FIGURE 3
FIGURE 1
5. Slide the long bag rod (28-1/2" long) through the
stiched bag flap on the top of the hopper bag as
shown in figure 4.
2. Assemble the Upper Handle Tube over the Handle
Leg Stand Tubes. See figure 2. Align holes in handle
and assemble the Bag Rod Clips to the handle as
shown and fasten with curved head bolts and hex lock
nuts.
6. Slide the short bag rod (25-1/2" long) through the
stiched bag flap on the bottom of the hopper bag as
shown in figure 4.
FIGURE 2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Assemble the two plastic rod caps to the rod ends of
the bottom bag rod. Assemble two Palnuts to the ends
of the top bag rod. See figure 5.
9. Place the upper hopper bag and bag rod into the bag
rod clips on the hopper handle. See figure 7.
FIGURE 7
FIGURE 5
10. Place the lower hopper bag and bag rod into the
opening on the sweeper housing. See figure 8.
8. Assemble the two plastic caps 3/4" x 7/8" onto the
ends of the leg stands as shown in figure 6.
FIGURE 8
FIGURE 6
5
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Hook the elastic straps on the bag flaps under the bag
rod clips on the lower handle tubes as shown in figure
9.
FIGURE 9
OPERATION
Take care when operating your sweeper. Operating your sweeper according to these instructions will help prevent damage
and prolong the life of your sweeper.
CAUTION: EYE PROTECTION SHOULD
To adjust your sweeper brushes to the best operating
height, loosen the hand knob and slide the height
adjustment tube down to raise or up to lower the brushes.
Best adjustment is when brushes are set 1/2" down
into the grass. Always mow grass to even height before
sweeping. See figure 10.
BE WORN WHILE OPERATING SWEEPER
DUMPING OF SWEEPER
To dump sweeper hopper bag, simply tip the sweeper
forward or lift off the complete hopper bag frame.
Always dump hopper after each use. Damp or wet grass
and leaves will cause damage to hopper if stored for long
periods of time.
CAUTION: DO NOT DUMP THE SWEEPER
TOO CLOSE TO A FIRE AS THE BRUSHES
AND BAG CAN BE DESTROYED BY
EXCESSIVE HEAT OR FLAME.
The entire unit may be hung on a wall or the hopper bag
frame can be removed for storage.
FIGURE 10
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
The bearings in the sweeper have been prelubricated at
the factory. It is recommended that a few drops of light
oil be added to the brush shaft bearings twice a year.
The wheels should be removed to clean gears every two
years. After cleaning, apply an even coat of light grease.
See figures 11 and 12.
1. Remove the hopper bag from lawnsweeper.
2. Brush replacement should be done one brush at a
time.
3. Tip the sweeper forward on housing for ease of brush
replacement. Do not remove hex bolt from double
brush retainers through brush shaft.
4. Loosen hex bolts and hex lock nuts from single brush
retainers. See figure 12. Slide brush out of retainers,
making not of over-lap bristles position.
5. Install new brush, making sure over-lap bristles are
postioned the same as before and as shown in figure
12.
IMPORTANT: Do not remove both wheels at the same
time to avoid mixing parts. (The R.H. and L.H. ratchet
gears are not interchangeable.) Make notes on the position
of washers and snap rings during disassembly.
1. Remove only one wheel from the sweeper.
2. Remove the retaining rings and washers which hold
the ratchet gear onto the brush shaft.
3. Remove the gear by sliding it off the brush shaft. (Look
for the drive pin, which may fall out of the brush shaft
when the ratchet gear is removed.
4. To reassemble, insert the drive pin through the hole
near the end of the brush shaft. Make sure the pin
slides back and forth easily in the shaft.
5. Lightly grease the shaft and fill the ratchet gear with
grease. Assemble the ratchet gear back onto the shaft.
6. Lightly grease the axle and the gear teeth on the
wheel and then reassemble the wheel.The brushes
should rotate only during forward movement. If the
brushes rotate by both forward and reverse movement,
the drive pin is jamming in the ratchet gear. Dissamble
clean and lubricate the drive pin and ratchet gear and
then reassmble wheel.
FIGURE 12
7. Remove opposite wheel and repeat steps 1-6 for that
wheel.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS
8
Download from Www.Somanuals.com. All Manuals Search And Download.
REF.
NO.
PART
NO.
REF.
NO.
PART
NO.
QTY.
DESCRIPTION
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
44600
23784
44286
43681
44680
1543-69
44695
R19111116
43720
44946
23866
44598
43070
44684
1038
1
1
4
1
1
1
1
1
1
1
2
2
4
2
2
2
2
2
2
2
4
4
4
2
1
1
2
Housing
28
29
30
31
32
33
34
35
36
37
38
39
40
41
44125
44687
1650-21
23782
43661
43013
44681
23580
23581
43012
44603
44595
44683
44682
4
2
4
1
4
8
4
4
8
8
1
2
1
1
2
2
4
4
4
4
1
4
12
1
Flat Washer, .62 x 1"
Plastic Cap, .207
Retaining Ring, .594
Brush Shaft
Bolt, Hex 1/4-20 x 1"
Lock Nut, 1/4-20
Brush, 13-1/4"
Brush Retainer, Double Bracket
Brush Retainer, Single Clip
Bolt, Hex 1/4" x 3/4"
Upper Handle Tube
Handle Leg Tube
Bag Rod, 1/4" x 25-1/2"
Bag Rod, 1/4" x 28-1/2"
Palnut, 1/4"
Plastic Cap, 3/4"
Bag, Rod Clip
Bolt, Curved 1.4-20 x 1"
Bolt, Hex 1/4-20 x 1-1/4"
Washer, 1/4"
Hopper Bag
Lock Nut, 10-32
Nylock Nut, 1/4-20
Owner's Manual
Height Adjustment Plate
Bolt, Hex 10-32 x 5/8"
Bolt, Carriage 5/16-18 x 1-1/2"
Washer, Nylon
Washer, Nylon 21/64
Washer, Bowed
Washer, 11/32 x 11/16
Knob, 5/16"
Height Adjustment Tube
Dust Cover
Axle
Washer, 3/8"
Jam Nut, 3/8-24
Nylock Jam Nut, 3/8-24
Shoulder Spacer
Washer, .596 x 1.125 x .025
"E" Ring, 5/8"
Flange Bearing, .59
Wheel Assembly
Flange Bearing, .63
Bolt, Hex 5/16-18 x 1/2"
Nylock Nut, 5/16-18
Black Hub Cap
42 726-0106
44685
40007
43
44
45
46
47
49
50
51
44688
44696
43978
1509-90
43088
44694
43662
47189
40258
18 716-0106
19
20
44679
49946
21 741-0249
22
23
24
25
26
27
44692
47810
2674-32
48651
48652
47046
Pinion, L.H.
Pinion, R.H.
Pin, Drive
9
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
10
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Get it fixed, at your home or ours!
Your Home
For repair–in your home–of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME® (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime, day or night (U.S.A. only)
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparación
a domicilio, y para ordenar piezas:
Au Canada pour service en français:
1-800-LE-FOYERMC
1-888-SU-HOGAR®
(1-800-533-6937)
(1-888-784-6427)
® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC
® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC
MC Marque de commerce / MD Marque déposée de Sears Brands, LLC
© Sears Brands, LLC
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|