Parts Manual for
MID MOUNT LARGE FRAME Z-RIDER
ZERO TURNING HYDRO DRIVE NZMX
SERIES 4
MODEL
NZMX30614KH
NZMX32734BV
McDonough, GA, 30253 U.S.A.
COPYRIGHT © 2006
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
Manual No.
7006940
Revision IR, 9/28/2006
TP 400-5234-IR-NZ-N
Table Of Contents
PAGE
4
6
GROUP
CASTER WHEEL ASSEMBLY
DRIVE TIRE & WHEEL ASSEMBLY
FRONT CHASSIS ASSEMBLY (Frame)
FRONT CHASSIS ASSEMBLY (Deck Lift)
REAR CHASSIS, PUMPS & PULLEYS
TRACTION DRIVE ASSEMBLY
HOSE & CONNECTOR ASSEMBLY
WHEEL MOTOR ASSEMBLY
8
10
14
16
18
20
22
26
28
30
32
34
36
38
40
44
46
48
52
54
56
58
60
62
64
66
68
70
TWIN STICK CONTROL ASSEMBLY
PARKING BRAKE ASSEMBLY
HYDRO RESERVOIR ASSEMBLY
FUEL TANK ASSEMBLY
ENGINE GROUP
SEAT ASSEMBLY
BUMPER ASSEMBLY
ROLL BAR PROTECTIVE STRUCTURE
61” CUTTING DECK ASSEMBLY (Sub Assy)
61” CUTTING DECK ASSEMBLY (Final Assy)
IDLER ASSEMBLY (61” Deck)
73” CUTTING DECK ASSEMBLY (Sub Assy)
73” CUTTING DECK ASSEMBLY (Final Assy)
IDLER ASSEMBLY (73” Deck)
DECK SPINDLE ASSEMBLIES
DECALS
CONTROL PANEL ASSEMBLY
ELECTRICAL COMPONENTS
WIRING HARNESS (Briggs Engines)
WIRING HARNESS (Kohler Engines)
WIRING SCHEMATIC (Briggs Engines)
WIRING SCHEMATIC (Kohler Engines)
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
3
CASTER WHEEL ASSEMBLY
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
4
CASTER WHEEL ASSEMBLY
Item Part No
Qty Description
Note
1
2
3
4
4
5
7092094
7075398
7091325
7075461
7072795
7075463
2
2
2
2
2
1
1
2
1
1
1
SCREW, 1/2-13 x 9-1/2” Hex Head Cap, GR 5
WELDMENT, Caster Yoke, 7-1/4” Wide
NUT, 1/2-13 Hex Nyloc
ASSEMBLY, Wheel & Tire
ASSY, Wheel & Tire, 13 x 6.50-6 (Incl. items 5A & 8A)
TIRE, 13 x 6-6.5 4 Ply
5A 7078277
TIRE, 13 x 6-6.50-6 4 Ply Smooth TL (not shown)
BALL BEARING, Heim .750
6
7
8
7028722
7012700
7075460
Heim Unibal # RF 12-22-14AP
Tapered Head w/Ball Check
FITTING, 1/4-28 Lube
WELDMENT, Front Wheel Rim
ASSEMBLY, Painted Rim (not shown)
8A 7078285
Assembly includes Grease
Fitting & 2 Ball Bearings.
9
7012234
1
AIR VALVE STEM & Cap
Goodyear # TR-412 or
equivalent
10
11
7075883
7075462
2
2
SPACER
SPACER, Bearing, 7.29” Long
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
5
DRIVE TIRE & WHEEL ASSEMBLY
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
6
DRIVE TIRE & WHEEL ASSEMBLY
Item Part No
Qty Description
Note
1
2
3
4
7100524
7072888
7100297
7012234
2
1
1
1
TIRE ASSEMBLY, 26” x 12-2 Multi-Trac
TIRE, 26 x 12.00-12 4 Ply Titan Multi-Trac
RIM, 12 x 8.50 5/4.5 RAW
AIR VALVE STEM & Cap
Goodyear # TR-412 or
equivalent
5
6
7
8
7092073
7071819
7092083
7091809
10
2
LUG BOLT, 1/2-20 UNF x 7/8”
DRUM, Brake (Ausco)
2
CASTLE NUT, 1-14 UNF, GR B
COTTER PIN, 1/8 x 1-1/4”
KEY, Woodruff
included as part of wheel motor
included as part of wheel motor
included as part of wheel motor
2
2
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
7
FRONT CHASSIS ASSEMBLY (Frame)
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
8
FRONT CHASSIS ASSEMBLY (Frame)
Item Part No
Qty Description
Note
1
2
7400018
1
2
WELDMENT, Front Frame
GROUP, Front Wheel
ref: Caster Wheel Assembly
Page
3
4
7074723
7058554
2
4
GREASE SEAL
BEARING, Tapered Roller
7074706 (tapered roller brg.) &
7074707 (inner race)
5
7029137
7092083
7090841
7074537
7400114
7090517
7090118
7091304
7041818
7100275
7300145
7100277
7300209
7090361
7090768
7091325
7100527
2
2
SPACER, Jackstaff
6
CASTLE NUT, 1-1/ UNF, GR B
ROLL PIN, 3/16 x 1-1/2”
CAP, Dust
7
2
8
2
9
1
WELDMENT, Foot Pedestal
WASHER, 3/8” Flat SAE
WASHER, 3/8” Split Lock
SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
PAD, Floor Board Support
FLOOR MAT, Top
10
11
12
13
14
15
16
17
18
19
20
21
2
2
2
4
1
1
FOOTPAN
1
FOOTPAN, Mat
1
FOOT STAND, LFNZM
4
SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
BOLT, 1/2-13 x 1-1/2” Square Neck Carriage, GR 5
NUT, 1/2-13 Hex Nyloc
12
12
2
HEADLIGHT, w/Connectors
Also shown on Electronic
Components page.
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
9
FRONT CHASSIS ASSEMBLY (Deck Lift)
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
10
FRONT CHASSIS ASSEMBLY (Deck Lift)
Item Part No
Qty Description
SHOULDER BOLT, 5/16-18
Note
1
7015761
7400161
7090591
7090122
7400087
7200075
7091640
7200080
7090951
7091299
7100652
7100804
7075086
7090543
7091587
7101001
7035667
7090361
7400050
7091325
7091803
7073326
7044860
7091894
7075782
7091316
7090509
7400051
7400049
7092063
7091315
1715834
7400147
7100274
7090559
7073012
7029355
1
1
3
8
1
2
1
1
1
5
1
1
1
5
10
4
1
1
1
2
2
5
1
4
4
8
4
1
1
1
1
1
1
1
1
1
1
2
WELDMENT, Transport Lever
SCREW, 3/8-16 x 4-1/2 Hex Head Cap, GR 5
WASHER, 3/8” Flat SAE
3
4
5
WELDMENT, Detent
6
SPACER LIFT
7
BOLT, 3/8-16 x 1” Square Neck Carriage, GR 5
DETENT SPACER, Upper
NUT, 5/16-18 Large Flange Hex Center Lock
NUT, 3/8-16 Hex Nyloc
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
DECAL, Detent Channel
CLIP, Roll Pin, 1/2”
STRAP, Tether
SCREW, 1/2-13 x 2” Hex Head Cap, GR 5
WASHER, .531 I.D. Flat
EYEBOLT, 1/2-13 Open
or 7074700
SPRING, Extension, Lift Assist
SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
WELDMENT, Bell Crank
NUT, 1/2-13 Hex Nyloc
KEY, 3/16” Square x 1-1/2”
BUSHING, Teflon
EYEBOLT, 3/8-16 x 3”
spring anchor
NUT, 1/2-13 Hex Center Lock, GR 5
SWIVEL, Rear Lift (1/2-13 thread)
NUT, 1/2-13 Hex GR B
WASHER, 3/8” Internal Tooth Lock
WELDMENT, Front Lift LH
WELDMENT, Rear Lift
WASHER, 5/16” Belleville
WASHER, 5/16” Split Lock
PEDAL, Rubber
WELDMENT, Foot Assist
ROD, Transfer (1/2-20 thread)
NUT, 1/2-20 Hex Jam, GR 5 or B
ROD END, 1/2-20 Female
BOLT, 1/2-13 x 3-3/4” Hex Head Cap
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
11
FRONT CHASSIS ASSEMBLY (Deck Lift)
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
12
FRONT CHASSIS ASSEMBLY (Deck Lift)
Item Part No
Qty Description
Note
38
39
40
41
42
43
44
45
46
7400017
7200059
7300281
7200083
7400117
7200077
7900033
7091544
7090848
1
1
WELDMENT, Front Deck Lift
SPACER
1
LINK PLATE
1
SPACER, Bearing
1
WELDMENT, Height Adjuster
SPACER, Bearing
1
1
BOLT, 1/2-13 x 4-1/2” Hex Head, GR 5
NUT, 1/2-13 Hex Flange Lock GR 5
SET SCREW, 5/16-18 x 1/2” Square Head Cup Point
10
4
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
13
REAR CHASSIS, PUMPS & PULLEYS
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
14
REAR CHASSIS, PUMPS & PULLEYS
Item Part No
Qty Description
Note
1
2
3
4
7400015
7100439
7100438
7074738
1
1
1
2
WELDMENT, Rear Chassis
PUMP, Hydro-Gear BDP-12A W/ RTN
PUMP, Hydro-Gear BDP-12A W/ RTN
* KIT, Fan Hub
left-hand pump
right-hand pump
(Hydro Gear p/n 70632) for BDP-
10A Pump w/Thru Shaft
5
7074968
7091299
7090122
7027199
7013847
7027181
7041330
7071831
7090548
7091627
7027223
7091835
7090361
7090071
7090052
7075919
5023096
1719168
2
4
4
2
4
4
2
2
4
2
2
2
4
4
4
2
2
2
FAN, 7” Nylon, Counter-Clockwise
NUT, 3/8-16 Hex Nyloc
6
7
WASHER, 3/8” Flat SAE
8
KEY, M5 x M20
9
BOLT RETAINER, 3/8”
10
11
12
13
14
15
16
17
18
19
20
21
22
BOLT, 3/8-16 x 1-1/4” Short Neck Carriage GR 5
PULLEY, 4.25 O.D. x 1.375 OA x “H” Tapered Bore
PULLEY, “D” Bushing x 15mm Bore
SCREW, 1/4-20 x 1” Hex Head Cap GR 5
WASHER, 1/4 x 1 x 1/8” Flat
WASHER, 1/4” Split Lock
double pump
SCREW, M6 1.0 x 12mm Hex Head Cap
SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
SCREW, 1/4-20 x 1/2” Hex Head Cap, GR 5
WASHER, 1/4” Split Lock
BRACKET, Filter
FILTER HEAD
FILTER
Footnotes:
* Note: Includes Fan Mount Hub, Belleville Washer and Hex Nyloc Nut.
MID MOUNT LARGE FRAME Z-RIDER
Manual No.
7006940
SERIES 4
TP 400-5234-IR-NZ-N
15
TRACTION DRIVE ASSEMBLY
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
16
TRACTION DRIVE ASSEMBLY
Item Part No
Qty Description
NUT, 3/8-16 Hex, GR 5 or B
Note
1
2
7090130
7090118
7090122
7091299
7041262
7200078
7300356
7091557
7091302
7074777
7044860
7073992
7027221
7090517
1723806
1723805
7400086
7091587
7091619
7100724
1
1
5
2
2
1
1
2
2
1
1
1
1
1
1
2
1
1
1
1
WASHER, 3/8” Split Lock
3
WASHER, 3/8” Flat SAE
4
NUT, 3/8-16 Hex Nyloc
5
PULLEY, 4” O.D. x .391 I.D. x 1.25 Backside Idler
SPACER, Pulley
6
7
MOUNT, Idler Spring
8
SCREW, 3/8-16 x 2-3/4” Hex Head Cap, GR 5
NUT, 3/8-16 Hex, GR 5 or B
SPACER, Lift Adjust (1.08” Long)
EYEBOLT, 3/8-16 x 3”
9
10
11
12
13
14
15
16
17
18
19
20
SPRING, Extension
BOLT, 3/8-16 x 3-1/2” Hex Head, GR 5
WASHER, 3/8” Flat SAE
BOSS, Idler Arm Pivot
SLEEVE BUSHING, 3/4” I.D.
WELDMENT, Drive Idler
WASHER, .531 I.D. Flat
NUT, 3/8-16 Hex Flange Lock
SET, Matched Traction Drive Belt
(Kit contains two belts (p/n
7100522)
21
22
7100522
7017853
2
1
BELT, HA Sect., 54.48” effective length
TRAY, Battery (Polypropylene)
4L Traction Drive
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
17
HOSE & CONNECTOR ASSEMBLY
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
18
HOSE & CONNECTOR ASSEMBLY
Item Part No
Qty Description
Note
1
2
3
4
5
6
7
8
9
7075055
7075056
7075057
7075058
7075051
7075052
7075053
7075054
7075470
4
6
2
4
2
2
2
2
2
CONNECTOR, 45-Degree Hydraulic (Parker # V5OLO-S)
CONNECTOR, 90-Degree Hydraulic (Parker # 8-6 C5OLO-S)
CONNECTOR, Straight Hydraulic (Parker # 8-6 F5OLO-S)
CONNECTOR, Straight Hydraulic (Parker # 8-10 F5OLO-S)
HOSE, 17-1/2” Hydraulic (Parker # F436BKJCJ5080808-17.5)
HOSE, 18-1/2” (Parker R836BKJCJ9090808-18.5)
HOSE, 12-1/4” (Parker # R836BKJ9NR080008-12.5)
HOSE, 6-1/2” (Parker # R836BKJ9NR080008-6.5)
HOSE, 15-1/2” Hydraulic (Parker # F436JCJ9080808-15.50)
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
19
WHEEL MOTOR ASSEMBLY
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
20
WHEEL MOTOR ASSEMBLY
Item Part No
Qty Description
Note
1
2
7400074
7090768
7075443
7091325
7029355
7092087
7100299
7100300
7091322
7091316
7091809
7071819
1
4
2
6
4
4
1
1
8
8
2
2
WELDMENT, Rear Support
BOLT, 1/2-13 x 1-1/2” Square Neck Carriage, GR 5
BRACKET, Wheel Motor Support
NUT, 1/2-13 Hex Nyloc
3
4
5
BOLT, 1/2-13 x 3-3/4” Hex Head Cap
BOLT, 1/2-13 x 6” Hex Head Cap GR 5
WHEEL MOTOR, LH HGM 18E-3052
WHEEL MOTOR, RH HGM 18E-3056
WASHER, 1/2” Split Lock
6
7
8
9
10
11
12
NUT, 1/2-13 Hex GR B
COTTER PIN, 1/8 x 1-1/4”
included as part of wheel motor
DRUM, Brake (Ausco)
shown also in DRIVE TIRE &
WHEEL ASSEMBLY
13
7092083
2
CASTLE NUT, 1-14 UNF, GR B
included as part of wheel motor
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
21
TWIN STICK CONTROL ASSEMBLY
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
22
TWIN STICK CONTROL ASSEMBLY
Item Part No
Qty Description
LIMITER BRKT, LH
Note
1
7300077
7300076
7074964
7090361
7100556
7100051
7300075
7300074
7072934
7091628
7400053
7091540
7090188
7027139
7091297
7100294
7091298
7091603
7091294
7073061
7090548
7010739
7090669
7100484
7090588
7075029
7091299
7071825
7091003
7091803
7079577
7090848
7400032
7400031
7090372
5022978
7900007
1
1
2
24
2
2
1
1
4
4
2
4
16
4
4
2
8
10
8
2
4
2
4
2
2
2
2
2
4
2
2
2
1
1
2
2
2
2
LIMITER BRKT, Twin Stick, Right Side, LFNZM
BRACKET, Speed Control
3
4
SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
HANDLEBAR, Twin Stick, LFNZM
FOAM GRIP, Handle
5
6
7
BUSHING MOUNT PLATE, LH
8
BUSHING MOUNT PLATE, Right Side, LFNZM
BUSHING, Teflon Impregnated
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
WASHER, .64 I.D. x .99 O.D. x .05 Flat
WELDMENT, Shaft Twin
SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5
WASHER, 5/16” Flat
ROD END (5/16-24 thread)
NUT, 5/16-24 Hex, GR 5 or B
LINKAGE, Pump Control (5/16-24 threads)
NUT, 5/16-18 Hex Nyloc
NUT, 1/4-20 Hex Nyloc
WASHER, 1/4” Flat
MOUNTING PLATE, Left Hand Bearing
SCREW, 1/4-20 x 1” Hex Head Cap GR 5
RING, 5/8” External Retaining
or 7027230
or 7091305
or 7091813
SCREW, 5/16-18 x 1-3/4” Hex Head Cap, GR 5
MOUNTING ARM, Twin Stick
SCREW 3/8-16 x 2” Hex Head Cap, GR 5
SPACER, .498 O.D. x 1.010” long
NUT, 3/8-16 Hex Nyloc
BRACKET, Handle Adjustment
SCREW, 1/4-20 x 1-3/4” Hex Head Cap, GR 5
KEY, 3/16” Square x 1-1/2”
SCREW, 1/4-20 x 1-1/2” Hex Head Cap GR 5
SET SCREW, 5/16-18 x 1/2” Square Head Cup Point
MOUNTING HUB WELDMENT, T-Stick LH
MOUNTING HUB WELDMENT, T-Stick RH
NUT, 1/4-20 Hex Center Lock
DAMPENER, Hydraulic
SCREW, Shoulder Socket Head
(1/4-20 thread)
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
23
TWIN STICK CONTROL ASSEMBLY
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
24
TWIN STICK CONTROL ASSEMBLY
Item Part No
Qty Description
Note
38
39
40
7027174
7090585
7300144
2
4
1
SCREW, 5/16-18 x 2” Hex Head Cap, GR 5
NUT, 5/16-18 Hex Flange Lock
CENTER BRACKET, Joystick
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
25
PARKING BRAKE ASSEMBLY
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
26
PARKING BRAKE ASSEMBLY
Item Part No
Qty Description
RING, 5/8” External Retaining
Note
1
2
7010739
7092091
7024159
7011231
7046451
7046782
7400016
7059085
7059086
7059087
7071820
7041140
7072934
7073989
7072094
7074196
7090122
7090482
7091518
7091298
7091508
7091628
7041148
7091585
3
1
8
2
2
2
1
1
2
2
2
2
6
2
2
1
4
2
2
6
6
5
4
4
GROOVE PIN, 1/4 x 1-1/4” long
PIN, 3/8” Self Locking Cotter
3
or 7091593
4
SWIVEL, 3/8” Thru Hole, Special
SWIVEL, 3/8-24 Adjustment
5
6
SPRING, Rectangular Wire Die, Blue
WELDMENT, Brake Rod
7
8
WELDMENT, Park Brake Handle
WELDMENT, Park Brake Pivot Bracket
WELDMENT, Brake Linkage Bellcrank
ASSEMBLY, Brake
9
10
11
12
13
14
15
16
17
18
24
19
20
21
22
23
Ausco p/n CC 83022
PLATE, Brake Mounting
BUSHING, Teflon Impregnated
FRONT LINKAGE, Park Brake (3/8-24 thread)
ROD, Brake Rear (3/8-16 thread)
GRIP, Parking Brake
WASHER, 3/8” SAE Flat
NUT, 3/8-24, Hex Jam, GR 5 or B
NUT, 3/8-24 Hex Nyloc
NUT, 5/16-18 Hex Nyloc
BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5
WASHER, .64 I.D. x .99 O.D. x .05 Flat
SHOULDER BOLT, 3/8-16 Hex Socket Head
NUT, 3/8-16 Hex Center Lock
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
27
HYDRO RESERVOIR ASSEMBLY
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
28
HYDRO RESERVOIR ASSEMBLY
Item Part No
Qty Description
Note
1
2
7059088
7074002
7075289
7075687
7073238
7073999
7074001
7090548
7091294
7090361
7091603
7012080
2
1
ASSY, Hydraulic Tank (Includes 4 items shown below)
TANK, Hydraulic, NZM
per 7059088, Tank Assembly
per 7059088, Tank Assembly
per 7059088, Tank Assembly
per 7059088, Tank Assembly
3
1
CAP, Vented (Kelch # H4550D)
GROMMET (Dapco # 12078)
ELBOW FITTING (Dapco # 12183)
BRACKET, R.H. Hydro Tank Mount
BRACKET, L.H. Hydro Tank Mount
SCREW, 1/4-20 x 1” Hex Head Cap GR 5
WASHER, 1/4” Flat
4
2
5
2
6
1
7
1
8
8
9
16
4
10
11
12
SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
NUT, 1/4-20 Hex Nyloc
8
5
CABLE TIE, 7” Long (not shown)
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
29
FUEL TANK ASSEMBLY
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
30
FUEL TANK ASSEMBLY
Item Part No
Qty Description
Note
1
7024669
1
ASSEMBLY, LH Fuel Tank
includes: tank (7042924) plus
items 3, 6, 7, 8 & 10
2
7100217
1
ASSEMBLY, RH Fuel Tank
includes: tank (7042925) plus
items 3, 6, 7, 9 & 10
3
7046326
7074835
7046804
7012337
7078165
7011247
7100211
7075135
7092089
7090250
7091294
7027223
7090825
7092088
7090188
7091298
7091640
7091299
7091917
7044681
7300382
7074688
7012222
7012080
1
1
1
1
1
1
1
1
6
8
2
2
2
2
2
2
2
2
6
1
1
3
6
5
ASSEMBLY, Fuel Pickup
ELBOW, 90 Degree
includes items 4 & 5
Dapco p/n 10672
4
5
TUBE, Pickup
6
GROMMET, Tube
7
GAGE, Fuel
8
GROMMET, Gage
9
LID, Fuel Tank
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
CAP, 3-1/2” Fuel
Kelch p/n 201906
SCREW, 7/16-14 x 2” Hex Head Cap, GR 5
WASHER, 1/2” Flat SAE
WASHER, 1/4” Flat
WASHER, 1/4” Split Lock
SCREW, 1/4-20 x 1-1/4” Hex Head Cap, GR 5
SCREW, 5/16-18 x 2-1/2” Hex Head Cap, GR 5
WASHER, 5/16” Flat
NUT, 5/16-18 Hex Nyloc
BOLT, 3/8-16 x 1” Square Neck Carriage, GR 5
NUT, 3/8-16 Hex Nyloc
NUT, 7/16-14 Hex Nyloc
FUEL VALVE, 3-Way
BRACKET, Tank Selector
HOSE, 1/4” I.D. x 3'-7.5” Long Fuel
CLAMP, Fuel Hose
CABLE TIE, 7” Long (not shown)
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
31
ENGINE GROUP
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
32
ENGINE GROUP
Item Part No
Qty Description
Note
1
1
* ENGINE, 32 HP Briggs Vanguard Vertical
Model # 543777 Type 0120 Trim
E1
1
1
4
4
4
5
1
2
1
2
1
1
1
1
1
1
1
1
1
* ENGINE, Kohler 30 HP (not shown)
SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5
BOLT RETAINER, 5/16” Bolt
WASHER, 5/16” Flat
Model # CV750S
2
3
7091540
7011791
7090188
7091706
7100803
7091640
7300399
7091299
7200094
7016755
7100292
7200058
7017033
7100436
7075082
7091301
4
5
NUT, 5/16-18 Hex Top Lock GR B
ASSEMBLY, Oil Drain Hose
6
used on Briggs Model only
used on NZMX32734BV
7
BOLT, 3/8-16 x 1” Square Neck Carriage GR 5
GUARD, Muffler NZMX
8
9
NUT, 3/8-16 Hex Nyloc
10
10
11
12
13
14
15
16
KEY, 1/4” Square x .360”
used on Briggs Model only
used on Kohler model
KEY, 1/4” Square x 3/4”
PULLEY, 4.26 O.D. x 1.375 OAL x 1.125 Bore
SPACER, Clutch
KEY, 1/4” Square x 2-1/4” Long
ELECTRIC CLUTCH, GT3.5
Qgura Model # GT3.5-FE05
for Ogura Clutch
WASHER, .468 x 1.85 x .25 Flat
WASHER, 7/16” Split Lock
17A 7100712
SCREW, 7/16-20 x 2” Hex Head Cap, GR 5
(w/Nyloc Patch); used on Briggs
model
17B 7027266
1
SCREW, 7/16-20 x 3” Hex Head Cap, GR 5
(w/Nyloc Patch); used on Kohler
model
18
19
20
21
22
23
24
25
26
27
28
29
30
7091497
7073012
7090517
7090122
7090155
7090559
7100586
7091304
7300217
7091585
7090361
7075734
7091581
1
1
3
1
1
1
1
1
1
2
2
1
4
SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR 5
ROD END, 1/2-20 Female
WASHER, 3/8” Flat SAE
WASHER, 3/8” Flat SAE
NUT, 3/8-24 Hex, GR B
NUT, 1/2-20 Hex Jam, GR 5 or B
CLUTCH ROD (1/2-20 thread)
SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
BRACKET, Clutch
NUT, 3/8-16 Hex Center Lock
SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
OUTLET, Muffler
used on NZMX30614KH only
SCREW, #8-18 x 1/2” Hex Washer Self-Tap
Footnotes:
* NOTE: Purchase engine components directly from engine manufacturer dealer.
MID MOUNT LARGE FRAME Z-RIDER
Manual No.
7006940
SERIES 4
TP 400-5234-IR-NZ-N
33
SEAT ASSEMBLY
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
34
SEAT ASSEMBLY
Item Part No
Qty Description
Note
1
7029338
1
SEAT ASSY, Mid Back Trim Line Static Suspension
Seats Inc. p/n 179035VD310
Silver/Black
2
7012080
7300207
7091298
7090799
7100817
7091640
7090361
7091067
7011791
7300126
7075433
7074218
7090122
7091299
7300451
7300441
7026292
7091595
7015761
7300452
7400151
7027174
7090188
7035638
7033362
7023354
7022793
7026249
7022794
7071767
7091289
7900040
7300442
3
1
8
2
1
2
6
2
6
1
1
2
2
2
1
1
1
4
4
1
1
2
18
1
1
1
2
2
2
2
2
2
1
CABLE TIE, 7” Long
3
FAN GUARD
4
NUT, 5/16-18 Hex Nyloc
5
BOLT, 5/16-18 x 5/8” Short Neck Carriage, GR 5
DECAL, Caution Fan
6
7
BOLT, 3/8-16 x 1” Square Neck Carriage GR 5
SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
NUT, 5/16-18 Hex Center Lock
BOLT RETAINER, 5/16” Bolt
CROSSMEMBER, Seat Support
DECAL, Oil Level Reservoir
SPRING, Compression- Seat Support
WASHER, 3/8” SAE Flat
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
NUT, 3/8-16 Hex Nyloc
SEAT LATCH, Left
BRACKET, Seat Latch, NZMX
SPRING, Extension
WASHER .47 x .92 x .065 Flat
SHOULDER BOLT, 5/16-18
LINK, Seat Latch
WELDMENT, Seat Pan
SCREW, 5/16-18 x 2” Hex Head Cap, GR 5
WASHER, 5/16” Flat
CLIP, Open J 3/8” Cushioned
HOLDER, Seat Switch
SWITCH, Seat, NC
BUSHING, Seat (Black Nylon)
SPACER/WASHER
SPACER
SPRING, Compression
SCREW, #10-32 x 5/8” Hex Washer Self-Tap, GR 5
SCREW, 5/16-18 x 5-1/2” Hex Head Cap, GR 5
BRACKET, Seat Stop, NZMX
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
35
BUMPER ASSEMBLY
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
36
BUMPER ASSEMBLY
Item Part No
Qty Description
Note
1
2
7400089
7400142
7100843
7300437
7090361
7091640
7091299
7090122
7013847
7300438
7091298
7300219
7091303
5100683
1
1
WELDMENT, Bumper LH
WELDMENT, Bumper
3
1
DECAL, Warning, Rollbar (Spanish)
GUARD, Hot Plate
4
1
used on Kohler Model only
5
2
SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
BOLT, 3/8-16 x 1” Square Neck Carriage GR 5
NUT, 3/8-16 Hex Nyloc
6
14
14
8
7
8
WASHER, 3/8” Flat SAE
9
4
BOLT RETAINER, 3/8”
10
11
12
13
14
2
BRACKET, Bumper Support, Middle
NUT, 5/16-18 Hex Nyloc
2
1
BRACKET, Rear Bumper
2
BOLT, 5/16-18 x 1” Short Neck Carriage, GR 5
DECAL, Warning, Rollbar
1
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
37
ROLL BAR PROTECTIVE STRUCTURE
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
38
ROLL BAR PROTECTIVE STRUCTURE
Item Part No
Qty Description
WELDMENT, Loop
Note
1
2
7100675
7100099
7100095
7029355
7300446
7090975
7100674
7091299
7900033
7091304
7300314
7100228
7091585
7100227
7090646
7100284
7100173
7100172
7100171
7100170
1
2
2
2
2
7
2
5
4
7
2
1
1
1
1
1
1
1
1
1
STAR KNOB (5/16-18 thread)
PIN, Hinge (ROPS)
3
4
BOLT, 1/2-13 x 3-3/4” Hex Head Cap
BRACKET, ROPS Stop, NZMX
NUT, 1/2-13 Hex Center Lock, GR 5
WELDMENT, Post
5
6
or 7091894
7
8
NUT, 3/8-16 Hex Nyloc
9
BOLT, 1/2-13 x 4-1/2” Hex Head, GR 5
SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
PLATE, Seat Belt
10
11
12
13
14
15
16
17
18
19
20
SEAT BELT, w/Metal Strap
NUT, 3/8-16 Hex Center Lock
RETRACTER, Seat Belt
SCREW, 1/2-13 x 1” Hex Head Cap, GR 5
DECAL, ROPS Overhang
DECAL, Warning ROPS (Spanish)
DECAL, Warning ROPS
DECAL, Caution ROPS (Spanish)
DECAL, Caution ROPS
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
39
61” CUTTING DECK ASSEMBLY (Sub Assy)
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
40
61” CUTTING DECK ASSEMBLY (Sub Assy)
Item Part No
Qty Description
Note
1
7400157
7091640
7091299
7091304
7091553
7091331
7044752
7091585
7090517
7029355
7091325
7027327
7300420
7300421
7300212
7300214
7036460
7036461
7073142
7027344
7079868
7079882
7091617
7400153
7023747
7074720
7400154
7014669
7012709
7044839
7091541
7091305
7091619
7300418
7300419
7091822
7036457
1
12
15
12
2
WELDMENT, 61” Deck, NZMX
2
BOLT, 3/8-16 x 1” Square Neck Carriage, GR 5
NUT, 3/8-16 Hex Nyloc
3
4
SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR 5
WASHER, .406 x 1.50 x .120 Flat
SPACER, 3/4 O.D. x 13/32 I. D. x 3/4” long
NUT, 3/8-16 Hex Center Lock
WASHER, 3/8” Flat SAE
5
6
4
7
2
8
4
9
4
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
6
BOLT, 1/2-13 x 3-3/4” Hex Head Cap
NUT, 1/2-13 Hex Nyloc
12
1
WELDMENT, Pivot Pin
1
BRACKET, RH Front
1
BRACKET, LH Front
1
FRONT ROLLER BRKT, RH
FRONT ROLLER BRKT, LH
TUBE, Roller
1
1
1
ROD, Roller (1/2-13 Threaded)
ROLLER, Low Density Polyethylene
WASHER, 5/8” Flat SAE
3
or 7079226
2
2
ROLLER 3-3/4 Dia. x 4-13/16” long
TUBE, Axle
Polyethylene
2
2
SCREW, 3/8-16 x 6” Hex Head Cap, GR 5
WELDMENT, Caster, Gauge Wheel
BUSHING, 1” Machine
2
4
4
BUSHING, Idler (Powdered Metal)
WELDMENT, Gauge Wheel Support
LUBE FITTING, 3/16”
2
2
2
RING, 1” External Retaining
CAP, Caster Shaft
2
2
SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
SCREW, 3/8-16 x 2” Hex Head Cap, GR 5
NUT, 3/8-16 Hex Flange Lock
BRACKET, RH Rear
2
2
1
1
BRACKET, LH Rear
2
BOLT, 1/2-13 x 5” Hex Head
BRACKET, Gauge Wheel
2
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
41
61” CUTTING DECK ASSEMBLY (Sub Assy)
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
42
61” CUTTING DECK ASSEMBLY (Sub Assy)
Item Part No
Qty Description
Note
38
39
40
41
42
43
7029264
7036456
7300064
7044823
7029258
7029263
2
2
2
2
8
4
GAUGE WHEEL, Polyethylene
SPACER, Gauge Wheel
BRACKET, Stabilizer
WELDMENT, Pusher Bar
BUSHING- Suspension
SLEEVE, Suspension
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
43
61” CUTTING DECK ASSEMBLY (Final Assy)
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
44
61” CUTTING DECK ASSEMBLY (Final Assy)
Item Part No
Qty Description
SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
Note
1
2
7090361
7075384
4
2
1
3
1
1
1
1
1
1
1
7
2
1
1
1
4
1
1
SPINDLE COVER, 61” Deck
3
ASSEMBLY, Idler (ref. Idler Assy page)
SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
* BELT, HB Section
4
7091304
7100912
7029268
7029278
7072915
7027950
7091313
7029277
7091299
5
(97.0” nominal effective length)
(127.0” nominal effective length)
6
* V-BELT, Secondary- 61” (HB Section)
SPRING, Idler (1.17” O.D. x 7.5” long)
SPRING, Idler Primary (1.25” O.D. x 10” long)
SPRING, Chute
7
8
9
10
11
12
13
14
15
16
17
18
19
COTTER PIN, 3/32 x 1”
PIN, Chute Hinge
NUT, 3/8-16 Hex Nyloc
ASSY, Outer Spindle (ref. Deck Spindle Assy page)
ASSY, Center Spindle (ref. Deck Spindle Assy page)
ASSEMBLY, 61” Discharge Chute
DEFLECTOR BOTTOM (61” Deck)
BOLT, 3/8-16 x 1-1/4” Square Neck Carriage, GR 5
CHUTE, Rubber (61” Deck)
7500232
7300034
7091790
7100622
7400007
incl. items 12, 16, 17, 18 & 19
WELDMENT, Discharge Chute 61”
Footnotes:
* NOTE: Snapper part number stamped on belt
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
45
IDLER ASSEMBLY (61” Deck)
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
46
IDLER ASSEMBLY (61” Deck)
Item Part No
Qty Description
Note
1
2
7058147
1
1
WELDMENT, Idler Plate
ASSEMBLY, Primary Idler
Includes items 6 (2), 7, 8 (3), 9,
10, 11, 12, 13 & 14
3
1
ASSEMBLY, Secondary Idler
Includes items 6 (2), 7, 8, 9, 15,
16 & 17
4
5
7023747
7012709
7074720
7014669
7090517
7091585
7027220
7058877
7035657
7035656
7034422
7091553
7058329
7029273
2
2
2
2
4
2
1
1
1
1
1
1
1
1
BUSHING, 1” Machine
RING, 1” External Retaining
BUSHING, Idler (Powdered Metal)
LUBE FITTING, 3/16”
6
7
8
WASHER, 3/8” Flat SAE
9
NUT, 3/8-16 Hex Center Lock
SCREW, 3/8-16 x 3-1/4” Hex Head Cap, GR 5
WELDMENT, Primary Idler Arm
BUSHING- Idler
10
11
12
13
14
15
16
17
RETAINER, Idler Belt
PULLEY, Flat Idler, 5.0 x .375 (Belt Clutch)
SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR 5
WELDMENT, Secondary Idler Arm
PULLEY, Idler
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
47
73” CUTTING DECK ASSEMBLY (Sub Assy)
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
48
73” CUTTING DECK ASSEMBLY (Sub Assy)
Item Part No
Qty Description
BOLT RETAINER, 5/16” Bolt
Note
1
7011791
7090799
7091299
7091304
7091640
7074720
7090517
7091585
7029258
7029355
7029263
7044823
7091922
7300019
7091305
7091331
7012117
7091619
7091541
7044839
7012709
7023747
7400154
7014669
7091617
7400153
7079882
7079868
7044752
7400004
7091553
7300064
7300176
7300177
7091325
7036456
7029264
6
6
22
13
22
4
4
4
8
4
4
2
4
1
2
4
2
2
2
2
2
4
2
2
2
2
2
2
2
1
3
2
1
1
5
2
2
2
BOLT, 5/16-18 x 5/8” Short Neck Carriage, GR 5
NUT, 3/8-16 Hex Nyloc
3
4
SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
BOLT, 3/8-16 x 1” Square Neck Carriage, GR 5
BUSHING, Idler (Powdered Metal)
WASHER, 3/8” Flat SAE
5
6
7
8
NUT, 3/8-16 Hex Center Lock
BUSHING- Suspension
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
BOLT, 1/2-13 x 3-3/4” Hex Head Cap
SLEEVE, Suspension
WELDMENT, Pusher Bar
NUT, 1/2-13 Hex Light Nyloc
73” DECK STIFFENER
SCREW 3/8-16 x 2” Hex Head Cap, GR 5
WASHER, .406 x 1.50 x .120 Flat
BUSHING, 3/8” Plastic
NUT, 3/8-16 Hex Flange Lock
SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap
CAP, Caster Shaft
RING, 1” External Retaining
BUSHING, 1” Machine
WELDMENT, Gauge Wheel Support
LUBE FITTING, 3/16”
SCREW, 3/8-16 x 6” Hex Head Cap, GR 5
WELDMENT, Caster, Gauge Wheel
TUBE, Axle
ROLLER 3-3/4 Dia. x 4-13/16” long
SPACER, 3/4 O.D. x 13/32 I. D. x 3/4” long
WELDMENT, 73” DECK
Polyethylene
SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR 5
BRACKET, Stabilizer
BRACKET, Deck Lift, RH Rear
BRACKET, Deck Lift, LH Rear
NUT, 1/2-13 Hex Nyloc
SPACER, Gauge Wheel
GAUGE WHEEL, Polyethylene
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
49
73” CUTTING DECK ASSEMBLY (Sub Assy)
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
50
73” CUTTING DECK ASSEMBLY (Sub Assy)
Item Part No
Qty Description
Note
38
39
40
41
42
43
44
45
46
47
48
7036457
7091822
7300175
7300285
7027327
7036461
7300212
7300214
7036460
7073142
7027344
2
2
2
2
1
1
1
1
1
3
2
BRACKET, Gauge Wheel
BOLT, 1/2-13 x 5” Hex Head
DECK LIFT BRACKET, Front
ANGLE, Deck Stiffener, 73 Deck
WELDMENT, Pivot Pin
ROD, Roller (1/2-13 Threaded)
BRACKET, Front Roller, RH
BRACKET, Front Roller, LH
TUBE, Roller
ROLLER, Low Density Polyethylene
WASHER, 5/8” Flat SAE
or 7079226
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
51
73” CUTTING DECK ASSEMBLY (Final Assy)
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
52
73” CUTTING DECK ASSEMBLY (Final Assy)
Item Part No
Qty Description
Note
1
2
3
4
5
7100516
7300129
6
1
1
3
1
KNOB, Fluted, 5/16-18 x 5/8”
GUARD, Pulley, RH
ASSEMBLY, Idler (see breakdown on Idler Assy page)
SCREW, 3/8-16 x 1” Hex Head Cap, GR 5
* BELT, HB Section, (engine to deck)
7091304
7100519
(106.434” nominal effective
length)
6
7100521
1
* V-BELT, Secondary, HB Section
(141.871” nominal effective
length)
7
7035667
7072915
7027950
7091313
7029277
7091299
1
1
1
1
1
7
2
1
1
1
4
1
1
1
SPRING, Extension, Lift Assist
SPRING, Idler Primary (1.25” O.D. x 10” long)
SPRING, Chute
8
9
10
11
12
13
14
15
16
17
18
19
20
COTTER PIN, 3/32 X 1”
PIN, Chute Hinge
NUT, 3/8-16 Hex Nyloc
ASSEMBLY, Spindle (ref. Deck Spindle Assy page)
ASSEMBLY, Center Spindle (ref. Deck Spindle Assy page)
ASSEMBLY, 73” Discharge Chute
DEFLECTOR, Bottom, 73” Deck
BOLT, 3/8-16 x 1-1/4” Square Neck Carriage, GR 5
CHUTE, Rubber, 73”
7500233
7300368
7091790
7100669
7400148
7300371
incl. items 12, 16, 17, 18 & 19
WELDMENT, Discharge Chute Top, 73”
GUARD, Pulley, LH
Footnotes:
* NOTE: Snapper part number stamped on belt
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
53
IDLER ASSEMBLY (73” Deck)
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
54
IDLER ASSEMBLY (73” Deck)
Item Part No
Qty Description
WELDMENT, Idler Pivot Plate
Note
1
2
7400113
1
1
1
2
2
4
2
1
1
1
1
2
2
3
2
2
2
2
1
1
ASSEMBLY, Primary Idler
ASSEMBLY, Secondary Idler
BUSHING, 1” Machine
3
4
7023747
7012709
7023556
7014669
7400111
7400112
7091553
7029273
7090517
7091585
7091305
7091331
7012117
7091619
7091299
7035789
7300444
5
RING, 1” External Retaining
BUSHING, Caster
6
7
LUBE FITTING, 3/16”
8
WELDMENT, Deck Idler Arm
WELDMENT, Secondary Idler Bracket
SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR 5
PULLEY, Idler
9
10
11
12
13
14
15
16
17
18
19
20
WASHER, 3/8” Flat SAE
NUT, 3/8-16 Hex Center Lock
SCREW 3/8-16 x 2” Hex Head Cap, GR 5
WASHER, .406 x 1.50 x .120 Flat
BUSHING, 3/8” Plastic
NUT, 3/8-16 Hex Flange Lock
NUT, 3/8-16 Hex Nyloc
PULLEY, Flat Idler, 5.5 O.D.
RETAINER- Belt- Idler
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
55
DECK SPINDLE ASSEMBLIES
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
56
DECK SPINDLE ASSEMBLIES
Item Part No
Qty Description
Note
1
2
7063237
7029270
7029250
7100518
7029245
7074401
7091299
7091154
7029422
7045092
7029384
7076998
7091640
7091790
7200025
7063238
7075770
7100721
7016440
7091976
3
2
NUT, 5/8-11 Hex Flange Lock, GR 5
WASHER, Spindle
3
1
PULLEY, Driven (61” Deck only)
PULLEY- Driven (73” Deck only)
PULLEY, 5.75” Diameter
3
1
4
3
5
6
WASHER, Spindle
6
18
6
NUT, 3/8-16 Hex Nyloc
7
RETAINING RING, Internal
8
6
BALL BEARING (double sealed, double shield)
WELDMENT, 48” Spindle
9
3
10
11
12
12
13
14
15
15
16
17
3
VENT, Spindle (Alemite # 321839)
LUBE FITTING, 1/4-28 Straight
BOLT, 3/8-16 x 1” Square Neck Carriage, GR 5
BOLT, 3/8-16 x 1-1/4” Square Neck Carriage, GR 5
SPINDLE SHAFT (5/8-11 threads)
SEAL, Nylos
3
or 7014669
18
18
3
used on 61” Decks
used on 73” decks
3
3
BLADE, 21” (61” Deck only)
3
BLADE, 25” (71” Deck only)
3
WASHER, Beveled
3
SCREW, 5/8-11 x 1-3/4” Hex Head Cap, GR 5
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
57
DECALS
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
58
DECALS
Item Part No
Qty Description
DECAL, Snapper Pro
Note
1
2
7074862
7100652
7100696
7100708
7100707
7075296
7100817
7100170
7100171
7075433
7075039
7100284
7035846
7073647
7100697
7100843
5100683
7100172
7100173
7075567
7046371
7027733
7045108
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
2
1
1
1
1
1
1
DECAL, Detent Channel
DECAL, Control Panel
3
4
DECAL, 3500 Z, 30 HP
5
DECAL, 3500 Z, 32 HP
6
DECAL, Caution, Spring Tension
DECAL, Caution Fan
7
8
DECAL, Caution ROPS
9
DECAL, Caution ROPS (Spanish)
DECAL, Oil Reservoir Overfill Warning
DECAL, Motion Control Levers
DECAL, ROPS Overhang
DECAL, Fuse
10
11
12
13
14
15
16
17
18
19
20
21
22
23
DECAL, Danger, Guard/Catcher
DECAL, Parking Brake Lever & Lights
DECAL, Warning (SP)
DECAL, Warning, Rollbar
DECAL, Warning ROPS
DECAL, Warning ROPS (Spanish)
DECAL, 61” Deck, (silver)
DECAL, 73” Deck
DECAL, Ear Protection
DECAL, Tank Selector, MMZ
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
59
CONTROL PANEL ASSEMBLY
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
60
CONTROL PANEL ASSEMBLY
Item Part No
Qty Description
Note
1
2
7300143
7035659
7090361
7072684
7091240
7075132
7074796
7075086
7300225
7074801
7090376
7100528
7100697
7100696
1
1
4
1
4
1
1
1
1
2
4
2
1
1
CONTROL PANEL, Detached
* SWITCH, Lights
3
SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
* SWITCH, Ignition
4
5
SCREW, #10-32 x 5/8” Hex Washer Self-Tap
* SWITCH, PTO, Yellow
6
7
* HOUR METER w/Flash Alerts
STRAP, Tether
8
9
CHOKE PLATE, Kohler
10
11
12
13
14
CONTROL LEVER, Throttle/Choke
NUT, #10-32 Nyloc
CABLE, Throttle Control
DECAL, Parking Brake Lever & Lights
DECAL, Control Panel
Ref: Decal Page
Ref: Decal Page
Footnotes:
* Note: Also shown on Electrical Components page.
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
61
ELECTRICAL COMPONENTS
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
62
ELECTRICAL COMPONENTS
Item Part No
Qty Description
Note
1
2
3
7075132
7012080
7023354
1
8
1
* SWITCH, PTO, Yellow
CABLE TIE, 7” Long
S WITCH, Seat, NC
also shown on SEAT
ASSEMBLY page
4
5
6
7
8
9
7072684
7091240
7090376
7015861
7100527
7074796
1
2
2
1
2
1
*SWITCH, Ignition
Indak p/n D473A
SCREW, #10-32 x 5/8” Hex Washer Self-Tap
NUT, #10-32 Nyloc
CLIP, Harness
HEADLIGHT, w/Connectors
* HOUR METER w/Flash Alerts
Sendec Corp. Model No. 804-
204
10
11
12
13
14
15
16
7035659
7090072
7075911
7091294
7090372
7022886
7073406
1
2
1
2
2
3
1
* SWITCH, Lights
SCREW, 1/4-20 x 5/8” Hex Head Cap GR 5
BATTERY, 11 Plate 375CCA- Wet
WASHER, 1/4” Flat
NUT, 1/4-20 Hex Center Lock
SWITCH, DP NO/NC Snap-In
KEY SET, Ignition (not shown)
qty. 2 keys per set
Footnotes:
* Note: Also shown on Control Panel Assembly Page.
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
63
WIRING HARNESS (Briggs Engines)
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
64
WIRING HARNESS (Briggs Engines)
Item Part No
Qty Description
Note
1
2
3
4
5
6
7
8
7074795
7100700
7100768
7100766
7100767
7100769
7075038
7035609
1
1
1
1
1
1
1
1
WIRE HARNESS, Briggs 32 HP
WIRE HARNESS, Lights
WIRE HARNESS, Engine
WIRE HARNESS, Ground
not shown
not shown
not shown
not shown
not shown
WIRE HARNESS, Power
WIRE HARNESS, Clutch
CABLE, Battery- Positive (6 Gage, 34” long)
CABLE, Battery- Ground (6 Gage/14 Gage, 23” long)
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
65
WIRING HARNESS (Kohler Engines)
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
66
WIRING HARNESS (Kohler Engines)
Item Part No
Qty Description
Note
1
2
3
4
5
6
7
7029337
7100700
7100766
7100767
7100769
7075038
7035609
1
1
1
1
1
1
1
WIRE HARNESS, Kohler/Twin
WIRE HARNESS, Lights
WIRE HARNESS, Ground
not shown
not shown
not shown
not shown
not shown
WIRE HARNESS, Power
WIRE HARNESS, Clutch
CABLE, Battery- Positive (6 Gage, 34” long)
CABLE, Battery- Ground (6 Gage/14 Gage, 23” long)
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
67
WIRING SCHEMATIC (Briggs Engines)
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
68
WIRING SCHEMATIC (Briggs Engines)
Item Part No
7074795
Qty Description
HARNESS, Wiring
Note
1
1
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
69
WIRING SCHEMATIC (Kohler Engines)
Manual No.
7006940
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
TP 400-5234-IR-NZ-N
70
WIRING SCHEMATIC (Kohler Engines)
Item Part No
7029337
Qty Description
HARNESS, Wiring, Kohler/Twin
Note
1
1
Footnotes:
MID MOUNT LARGE FRAME Z-RIDER
SERIES 4
Manual No.
7006940
TP 400-5234-IR-NZ-N
71
Parts Manual for
MID MOUNT LARGE FRAME Z-RIDER
ZERO TURNING HYDRO DRIVE NZMX
SERIES 4
IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS
WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE
RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS
AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE
SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY.
McDonough, GA, 30253 U.S.A.
COPYRIGHT © 2006
SNAPPER PRODUCTS, INC.
Manual No.
7006940
ALL RIGHTS RESERVED.
Revision IR, 9/28/2006
TP 400-5234-IR-NZ-N
|