OPERATION AND PARTS MANUAL
STR46SP
RIDE-ON POWER TROWEL
Revision #1 (08/01/06)
THIS MANUAL MUST ACCOMPANY
THE EQUIPMENT AT ALLTIMES.
To find the latest revision of this
publication, visit our website at:
P/N 21826
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING WARNING
SILICOSIS WARNING
RESPIRATORY HAZARDS
Grinding/cutting/drilling of masonry, concrete, metal and
other materials with silica in their composition may give
off dust or mists containing crystalline silica. Silica is a
basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Repeated and/or
substantial inhalation of airborne crystalline silica can
cause serious or fatal respiratory diseases, including
silicosis. In addition, California and some other
authorities have listed respirable crystalline silica as a
substance known to cause cancer. When cutting such
materials, always follow the respiratory precautions
mentioned above.
Grinding/cutting/drilling of masonry, concrete, metal and
other materials can generate dust, mists and fumes
containing chemicals known to cause serious or fatal
injury or illness, such as respiratory disease, cancer,
birth defects or other reproductive harm. If you are
unfamiliar with the risks associated with the particular
process and/or material being cut or the composition of
the tool being used, review the material safety data
sheet and/or consult your employer, the material
manufacturer/supplier, governmental agencies such as
OSHA and NIOSH and other sources on hazardous
materials. California and some other authorities, for
instance, have published lists of substances known to
cause cancer, reproductive toxicity, or other harmful
effects.
Control dust, mist and fumes at the source where
possible. In this regard use good work practices and
follow the recommendations of the manufacturers or
suppliers, OSHA/NIOSH, and occupational and trade
associations. Water should be used for dust
suppression when wet cutting is feasible. When the
hazards from inhalation of dust, mists and fumes cannot
be eliminated, the operator and any bystanders should
always wear a respirator approved by NIOSH/MSHA for
the materials being used.
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP —TABLE OF CONTENTS
Proposition 65 Warning ............................................. 2 Steering Handles Assembly (Right/Left) ............50-51
Respiratory/Silicosis Warnings .................................. 3 Steering Assist Control Assembly (Right/Left) ...52-53
Table of Contents ...................................................... 4 Gearbox Assembly (Right).................................54-55
Parts Ordering Procedures ....................................... 5 Gearbox Assembly (Left) ...................................56-57
Training Checklist ...................................................... 6 Single Pitch Handle Assembly (Right/Left) ........58-59
Daily Pre-Operation Checklist ................................... 7 Drive Assembly ..................................................60-61
Safety Message Alert Symbols .............................. 8-9 Engine/Muffler/Belt Assembly ............................62-63
Rules For Safe Operation ..................................10-13 Air Cleaner/Oil Filter/Oil Cleaner Assembly .......64-65
V-Belt Cover/Outer Muffler Shield Assembly .....66-67
Spider Assembly (Right) ....................................68-69
Spider Assembly (Left).......................................70-71
STOW — STR46SP RIDE-ON
POWER TROWEL
Yoke Assembly ...................................................72-73
Throttle Cable/Foot Pedals Assembly................74-75
Control Panel Assembly .....................................76-77
Fuel Assembly....................................................78-79
Battery Assembly ...............................................80-81
Seat Frame Assembly ........................................82-83
Operation And Safety Decals.................................. 14
Specifications .......................................................... 15
Engine Specifications .............................................. 16
General Information ................................................ 17
Controls and Indicators ......................................18-19
Basic Engine ........................................................... 20
New Machine Setup Instructions ............................ 21
Initial Start-Up ......................................................... 22
Operation ...........................................................23-24
Maintenance ......................................................25-38
Engine Troubleshooting......................................39-40
Troubleshooting (Trowel) ...................................41-42
Explanation of Code in Remarks Column ............... 44
Suggested Spare Parts ........................................... 45
Nameplate and Decals.......................................46-47
Pivot Assembly (Right/Left)................................48-49
Terms and Conditions of Sale ................................. 84
Specifications and part numbers
are subject to change without
notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — PARTS ORDERING PROCEDURES
When ordering parts,
please supply the following information:
❒
Dealeraccountnumber
❒
❒
❒
❒
❒
❒
Dealernameandaddress
Shipping address (if different than billing address)
Returnfaxnumber
Applicable model number
Quantity,part number and description of each part
Specifypreferredmethodofshipment:
✓
✓
✓
✓
✓
✓
FedEx or UPS Ground
FedEx or UPS Second Day or Third Day
FedEx or UPS Next Day
Federal Express Priority One
DHL
Note:Unlessotherwiseindicatedbycustomer, all
orders are treated as “Standard Orders”, and will
ship within 24 hours.We will make every effort to
ship “Air Shipments” the same day that the order is
received, if prior to 2PM west coast time. “Stock
Orders” must be so noted on fax or web forms.
Truck
Place Your Parts Order Via Web or Fax
For Even More Savings!
Here’s how to get help...
Please have the model and serial number
on hand when calling.
(Domestic USA Dealers Only)
STOW MAIN OFFICE
18910 Wilmington Ave.
Carson, CA 90746
800-421-1244
FAX: 310-537-3927
Extra Discounts!
All parts orders which include complete part numbers and
are received by our automated web parts order system, or
by fax qualify for the following extra discounts:
Email: [email protected]
Ordered
via
Standard
orders
Stock orders
SALES DEPARTMENT
310-661-4242
877-289-7869 (877-BUY-STOW)
PARTS DEPARTMENT
800-427-1244
310-537-3700
SERVICE DEPARTMENT
800-478-1244
310-537-3700
TECHNICAL ASSISTANCE
800-478-1244
($750 list and above)
Fax: 310-604-9237
Fax
3%
5%
10%
10%
Web
FAX: 800-672-7877
FAX: 310-637-3284
Special freight allowances
when you order 10 or more
line items via Web or Fax!**
FedEx Ground Service at no charge for freight
No other allowances on freight shipped by any other
carrier.
FAX: 310-537-4259
FAX: 310-631-5032
FAX: 310-537-1173
WARRANTY DEPARTMENT
800-421-1244, EXT. 279
310-537-3700, EXT. 279
**Common nuts, bolts and washers (all items under $1.00
list price) do not count towards the 10+ line items.
NOTE:DISCOUNTSARESUBJECTTOCHANGE
Direct TOLL-FREE access
to our Parts Department:
STOWCONSTRUCTIONEQUIPMENT
A DIVISION OF MULTIQUIP INC.
Toll-free nationwide — 800-427-1244
POST OFFICE BOX 6254
888-252-STOW[888-252-7869]
FAX:310-537-1986
CARSON, CA 90749
310-537-3700
FAX:800-556-1986
INTERNET:www.stowmfg.com
Toll-free FAX — 800-6-PARTS-7 (800/672-7877)
E-MAIL: [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — TRAINING CHECKLIST
TRAINING CHECKLIST
This checklist lists some of the minimum requirements for machine operation. Please feel free to make copies for daily use. Use this
checklist when training a new operator or use as a review for more experienced operators.
TRAINING CHECKLIST
NO.
DESCRIPTION
Read Operator’s Manual completely.
OK?
DATE
1
Machine layout, location of components, checking of engine and
fluid levels.
2
3
4
Fuel system, refueling procedure.
Operation of spray and lights.
Operation of controls (machine not running).
Safety controls, Safety Stop Switch operation.
Emergency stop procedures.
Startup of machine.
5
6
7
8
9
Maintaining a hover.
10
11
Maneuvering.
Pitching.
Matching blade pitch between towers Twin Pitch™, disengaging the
linkage. (Models with Twin Pitch™ option only.)
12
13
14
15
16
Concrete finishing techniques.
Shutdown of machine.
Lifting of machine (lift loops).
Machine transport and storage.
Operator _________________________________________ Trainee __________________________________________
COMMENTS:
PAGE 6 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 6
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — DAILY PRE-OPERATION CHECKLIST
DAILY PRE-OPERATION CHECKLIST
DAILY PRE-OPERATION CHECKLIST
1
2
3
4
5
6
7
8
Engine Oil Level.
Gearbox Fluid Level
.
Radiator Coolant Level.
Condition of Blades
.
Blade Pitch Operation.
Safety-Stop Switch Operation.
Steering Control Operation.
Condition of Belts.
COMMENTS:
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — SAFETY MESSAGE ALERT SYMBOLS
HAZARD SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
Safety precautions should be followed at all times when
operating this equipment. Failure to read, understand and
comply with the Safety Messages and Operating Instructions
could result in injury to yourself and others.
Lethal Exhaust Gases
Engine exhaust gases contain poisonous
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined
area or enclosed structure that does not
provide ample free flow air.
This Operation Manual has been
developed to provide instructions for the
safe and efficient operation of the STR46 -
Series Ride-On Trowel. For engine
maintenance information, please refer to the
engine manufacturer's instructions for data
relative to its safe operation.
Explosive Fuel
Before using this Ride-OnTrowel, ensure that the operating
individual has read, understands, and complies with all
instructions in this manual.
Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited. DO
NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank
while the engine is running or hot. DO NOT
overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas
and away from sparks and flames. NEVER
use fuel as a cleaning agent.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
Burn Hazards
DANGER
You WILL be KILLED or SERIOUSLY INJURED
if you DO NOT follow these directions.
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operations. NEVER operate the engine with
heat shields or heat guards removed.
WARNING
You CAN be KILLED or SERIOUSLY INJURED if
you DO NOT follow these directions.
Rotating Parts
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair
and clothing away from all moving parts to
prevent injury.
CAUTION
You CAN be INJURED if you DO NOT follow
these directions.
Potential hazards associated with trowel operation will be
referenced with Hazard Symbols which appear throughout this
manual, and will be referenced in conjunction with Safety
Message Alert Symbols.
PAGE 8 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 8
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — SAFETY MESSAGE ALERT SYMBOLS
Accidental Starting
Respiratory Hazard
Accidental starts can cause severe injury or death. ALWAYS
place the ON/OFF switch in the OFF position. Disconnect and
ground spark plug lead and disconnect negative battery cable
from battery before servicing.
ALWAYS wear approved respiratory
protection.
Sight and Hearing hazard
ALWAYS wear approved eye and hearing
protection.
Over Speed Conditions
NEVER tamper with the factory settings of the
engine governor or settings. Personal injury
and damage to the engine or equipment can
result if operating in speed ranges above
maximum allowable.
Equipment Damage Messages
Other important messages are provided throughout this manual
to help prevent damage to your trowel, other property, or the
surrounding environment.
CAUTION
This Ride-On trowel, other property, or the
surrounding environment could be damaged if you do
not follow instructions.
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — RULES FOR SAFE OPERATION
■
NEVER operate this equipment when not feeling well due to
fatigue, illness or taking medicine.
RULES FOR SAFE OPERATION
■
■
NEVER operate the trowel under the influence of drugs or
WARNING
alcohol.
Failure to follow instructions in this manual may lead to serious
injury or even death! This equipment is to be operated by
trained and qualified personnel only! This equipment is for
industrial use only.
Replace nameplate, operation and safety decals when they
become difficult to read.
■
■
ALWAYS check the trowel for loosened hardware such as
nuts and bolts before starting.
The following safety guidelines should always be used when
operating the STR46SP Ride-OnTrowel.
NEVERtouchthehotexhaustmanifold, muffler
or cylinder. Allow these parts to cool before
servicing the trowel. Contact with hot!
components can cause serious burns.
SAFETY
■
DO NOT operate or service this
equipment before you read, understand,
and comply with all safety messages in
this manual. The manual must be kept
available and accessible to the operator.
■
The engine of this trowel requires an adequate free flow of
cooling air. NEVER operate the trowel in any enclosed or
narrow area where free flow of
the air is restricted. If the air flow
■
■
■
This equipment should not be operated by persons under the
minimum statutory age limit.
is restricted it will cause serious
damage to the engine and may
cause injury to people.
Remember the engine gives off
DEADLY carbon monoxide
gas.
NEVER use this machine for any purpose other than those
described in this manual.
NEVER operate the trowel without proper protective clothing,
shatterproof glasses, steel-toed boots and other protective
devices required for the job.
■
ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
■
■
Topping-off to filler port is dangerous, as it tends to spill fuel.
NEVER use fuel as a cleaning agent.
■
ALWAYS use extreme caution when working with flammable
liquids. When refueling, STOP the engine. Allow the engine
to cool before adding fuel or performing service and
maintenance functions.
■
NEVER operate the trowel in an
explosive atmosphere where fumes
are present, or near combustible
materials. An explosion or fire could
result in severe bodily harm or even
death.
■
■
NEVER use accessories or attachments which are not
recommended by the manufacturer for this equipment.
Damage to the equipment and/or injury to user may result.
Manufacturer does not assume responsibility for any accident
due to equipment modifications. Unauthorized equipment
modification will void all warranties. Any modification which
could lead to a change in the original characteristics of the
machine should be made only by the manufacturer who shall
confirm that the machine is in conformity with appropriate
safety regulations.
■
NEVER smoke around or near the machine.
Fire or explosion could result from fuel
vapors, or if fuel is spilled on a hot! engine.
PAGE 10 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 10
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — RULES FOR SAFE OPERATION
■
NEVER run engine without air filter. Severe engine damage
may occur. Service air filter frequently to prevent carburetor
malfunction.
DANGER
Pay close attention to ventilation when
operating the trowel in confined spaces
such as tunnels, buildings or similar areas.
The engine exhaust contains harmful
elements. Ensure proper air flow to move
engine exhaust away from the operator.
■
■
NEVER place your feet or hands inside the guard rings
while starting or operating this equipment.
AVOID wearing jewelry or loose fitting clothing that may snag
on the controls or moving parts as this can cause a serious
injury.
■
■
ALWAYS keep clear of rotating or moving parts while
operating the trowel.
Moving Parts – Shut down the engine before performing
service or maintenance functions. Contact with moving parts
can cause serious injury.
Lifting the Ride-On Trowel
CAUTION
This ride-on trowel is very heavy and awkward to move
around. Use proper heavy lifting procedures and DO NOT
attempt to lift the ride-on trowel by the guard rings.
■
ALWAYS check to make sure that the operating area is clear
before starting the engine.
■
■
NEVER leave the machine unattended while running.
ALWAYS be sure the operator is familiar with proper safety
precautions and operations techniques before using trowel.
■
■
ALWAYS keep the work area well organized.
The STR46SP Ride-On PowerTrowel is designed to be moved
and handled several ways.
ALWAYS clear the work area of any debris, tools, etc. that
would constitute a hazard while the trowel is in operation.
The easiest way to lift the trowel is to utilize the lift loops that are
welded to the frame.These lift loops are located to the left and
right sides of the operator’s seat.
WARNING
ALWAYS check to make sure that the operating area is
clear before starting the engine.
A strap or chain can be attached to these lift loops, allowing a
forklift or crane to lift the trowel up onto and off of a slab of concrete.
The strap or chain should have a minimum 2,000 pounds (1000-
kg) lifting capacity and the lifting gear must be capable of lifting
at least this amount.
■
■
■
No one other than the operator is to be in the working area
when the trowel is in operation.
NEVER allow passengers or riders on the trowel during
operation.
DANGER
Always observe all applicable compulsory regulations
relevant to environmental protection, especially, fuel storage,
the handling of hazardous substances, and the wearing of
protective clothing and equipment. Instruct the user as
necessary, or, as the user, request this information and
training.
NEVER stand under or allow anyone
else to stand under the trowel while it
is being lifted.
■
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of
the reach of children.
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — RULES FOR SAFE OPERATION
Transporting
■
■
■
Use chock-blocks at each wheel when parked to prevent
trailer from rolling.
■
■
ALWAYS shutdown engine before transporting.
Use the trailer's swivel jack to adjust the trailer height to a
level position while parked.
Tighten fuel tank cap securely and close fuel petcock to
prevent fuel from spilling.
Avoid sudden stops and starts. This can cause the trailer to
skid or jack-knife. Smooth, gradual starts and stops will
improve towing.
■
■
■
Drain fuel when transporting trowel for long distances or over
bad roads.
When placing the trowel on a truck-bed for transport, always
tie-down the trowel.
■
■
Avoid sharp turns.
Trailer should be adjusted to a level position at all times
when towing.
If the trowel is being transported via a trailer, make sure the
trailer complies with all local and state safety transportation
laws. Refer to the following "Towing Safety Precautions"
for basic towing techniques.
■
■
Raise and lock trailer wheel stand in the "UP" position when
transporting.
DOT requirements include the following:
Connect and test electric brake operation.
Towing Safety Precautions
Secure portable power cables in cable tray with tie wraps.
CAUTION
Conform to Department ofTransportation (DOT) Safety
Towing Regulations before transporting trowel on public
roads.
Battery
The battery contains acids that can cause injury to the eyes and
skin. To avoid eye irritation, always wear safety glasses or face
shielding. Use well insulated gloves when picking the battery
up. Use the following guidelines when handling the battery.
To reduce the possibility of an accident while transporting the
trowel on public roads, always make sure the trailer that supports
the trowel and the towing vehicle are in good operating condition
and both units are mechanically sound.
■
■
DO NOT drop the battery. Any impact to
the battery may cause it to explode.
DO NOT expose the battery to open flames,
sparks, lit cigarettes etc. The battery
contains combustible gases and liquids. If
these gases and liquids come in contact
with a flame or spark an explosion can occur.
The following list of suggestions should be used when towing
your trowel:
■
Make sure the hitch and coupling of the towing vehicle are
rated equal to, or greater than the trailer "gross vehicle weight
rating" (GVWR) of 6,000 lbs.
■
■
ALWAYS keep the battery charged. If the
battery is not charged a buildup of combustible gas will occur.
■
■
ALWAYS inspect the hitch and coupling for wear. NEVER
ALWAYS keep battery cables in good working condition.
Repair or replace all worn cables.
tow a trailer with defective hitches, couplings, chains, etc.
Check the tire air pressure on both towing vehicle and trailer.
Trailer tires should be inflated to 50 psi cold. Also check
the tire tread wear on both vehicles.
■
■
ALWAYS disconnect the negative battery terminal before
performing service on the trowel.
ALWAYS recharge the battery in a vented air environment
to avoid risk of a dangerous concentration of combustible
gases.
■
■
ALWAYS make sure the trailer is equipped with "Safety
Chains ".
ALWAYS attach trailer's safety chains to towing vehicle
■
■
In case the battery liquid, (dilute sulfuric acid), comes in contact
with clothing or skin, rinse skin or clothing immediately
with plenty of water.
properly.
■
■
ALWAYS make sure the vehicle and trailer directional,
backup, brake, and trailer lights are connected and working
In case the battery liquid, (dilute sulfuric acid), comes in contact
with your eyes, rinse eyes immediately with plenty of water,
then contact the nearest doctor or hospital and seek medical
attention.
DO NOT exceed the recommended highway speed when
towing. Unless posted otherwise, do not exceed 45 MPH
highway, and 10 MPH off-road.
PAGE 12 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 12
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — RULES FOR SAFE OPERATION
Maintenance Safety
Emergencies
■
ALWAYS shut down the engine and disconnect battery before
performing service or maintenance functions. Contact with
moving parts can cause serious injury.
■
■
■
ALWAYS know the location of
the nearest fire extinguisher.
■
■
Securely support any trowel components that must be raised.
NEVER lubricate components or attempt service on a running
trowel.
ALWAYS know the location of the
nearest first aid kit.
■
ALWAYS allow the trowel a proper amount of time to cool
before servicing.
■
■
Keep the trowel in proper running condition.
Know the phone numbers of the nearest
ambulance, doctor and fire department. Ensure
that a phone or radio is readily available at the
jobsite. If this is not possible, know the location of
the nearest phone. This information will be
invaluable in the event of an emergency.
Make sure that there is no buildup of concrete, grease, oil or
debris on the machine.
■
■
■
■
■
Repair damage to the trowel immediately and always replace
broken parts.
Dispose of hazardous waste properly. Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
DO NOT use plastic food containers to dispose of hazardous
waste.
DO NOT pour waste oil or fuel directly onto the ground, down
a drain or into any water source.
NEVER store trowel with fuel in the tank for any extended
period of time. Always clean up spilled fuel immediately.
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — OPERATION AND SAFETY DECALS
Machine Safety Decals
The STR46SP Ride-On Power Trowel is equipped with a number of operation and safety decals. These decals are provided for
operator safety and maintenance information. Should any of these decals become unreadable, replacements can be obtained from
your dealer.
WARNING
To avoid injury,
you MUST read
and understand
operator’s manual
before using this
machine.
This machine to
be operated by
qualified
personnel only.
Ask for training
as needed.
P/N 35137
P/N 11111 11” x 3”
P/N 35137
CLOCKWISE
BELT DRIVE
P/N: 21455
P/N TBD
GEAR DRIVE GEAR DRIVE
CHECK
CHECK
WARNING
P/N 2814 (WHITE)
COUNTER
CLOCKWISE
HOT
P/N 36099 (ISO Blue)
ROTATING BLADE
HAZARD
LIFTING POINT LIFTING POINT
Keep hands
and feet clear
of guard rings.
Stop engine
before servicing.
P/N 35168
MODEL
SERIAL NO.
CONTACT
SERVICE
DEPARTMENT
LUBRICATION
LUBRICATION
P/N 35168
P/N 20953
LUBRICATION
LUBRICATION
Engine exhaust and some of
its constituents,and some dust created
by power sanding, sawing, grinding,
drillingandotherconstructionactivities
contains chemicals known to the State
of California to cause cancer, birth
defects and other reproductive harm.
Someexamplesofthesechemicalsare:
P/N: 11246
Leadfromlead-basedpaints.
Crystallinesilicafrombricks.
Cementandothermasonryproducts.
Arsenicandchromiumfromchemically
treatedlumber.
DECAL ENGINE
SPEED PLATE
DANGER
Your risk from these exposures varies,
dependingonhowoftenyoudothistype
of work. To reduce your exposure to
these chemicals: ALWAYS work in
a
DO NOT DISASSEMBLE
SPRING INSIDE IS
well ventilated area, and work with
approved safety equipment, such as
dust masks that are specially designed
to filter out microscopic particles.
UNDER COMPRESSION
2634
P/N 20525
P/N 2634
P/N 11811
P/N: 13118
PAGE 14 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 14
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — SPECIFICATIONS (TROWEL)
C
B
A
Figure 1. STR46SP Dimensions
Table 1. STR46 Specifications
A–Length – in. (cm)
95.0 (241.3)
48.0 (122)
B–Width – in. (cm)
C–Height – in. (cm)
46.0 (116.8)
705 (320.5)
1130 (513.6)
150
Weight – lbs. (kgs.) Operating
Weight – lbs. (kgs.) Shipping
Rotor – RPM (Dry Concrete)
Path Width – in. (cm)
91 (231)
Hand/Arm Vibration1
2.79 ft/s2 (m/s2)
TBD ft/s2 (m/s2)
90 dB(A)
Whole Body Vibration
Sound Pressure (A-Weighted)2
NOTE:
1.
2.
Sound pressure is a weighted measure. It is measured at
the operator's ear position while the walk-behind trowel is
operating at full throttle on concrete in a manner most often
experienced in “normal” circumstances. Sound pressure
may vary depending upon the condition of the concrete.
The vibration level indicated is the maximum RMS (Root
Mean Square) value obtained at the handle grip while
operating the walk-behind trowel at full throttle on steel
plate with blades partially pitched.
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — SPECIFICATIONS (ENGINE)
Table 2. STR46 Engine Specifications
STR46
Kohler 27 HP Engine
Model
4 Stroke, Overhead Valve V-Twin,
gasoline engine.
Type
Piston Displacement
Max. Output
44.0 cu.in. (725 cc)
27 bhp/3200 rpm (20.1 KW)
42.7 lbf-ft at 2200 rpm
Forced Air
Max. Torque
Cooling System
1.75 qt. (1.6 liters)
2.1 qt. (1.9 liters w/oil filter
replacement)
Engine Oil Capacity
Fuel Tank
5 gal.(19.23 liters)
69 oz. (2.041 L) (Mobil SCH 634
ISO VG640)
Gear Box Oil Capacity
Unleaded gasoline
Octane rating of 86 or higher
Fuel
Starting System
Spark Plug Type
Spark Plug Gap
Electric Start/Transistorized Magneto
see engine owner's manual
see engine owner's manual
PAGE 16 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 16
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — GENERAL INFORMATION
STR46 SERIES Ride-On PowerTrowel Familiarization
Gearboxes
The STR46 SERIES Ride-On Power Trowel is designed for the
floating and finishing of concrete slabs.
The STR46 Series Ride-On Power Trowel uses two separate
gearbox assemblies that are enclosed in rugged cast aluminum
gear cases.
Take a walk around your trowel. Take notice of all the major
components (see Figures 2 and 3, pages 20 and 21) like the
engine, blades, air cleaner, fuel system, fuel shut-off valve,
ignition switch etc. Ensure engine and gearbox oil levels are
within proper operating range.
The gearbox casing has a large oil capacity allowing optimum
lubrication to critical points.
Steering Assist
Dual control levers located in front of the operator's seat are
provided for steering the trowel.The control levers are linked to
two spring loaded cylinders.
Read all the safety instructions carefully.Safety instructions will
be found throughout this manual and on the machine. Keep all
safety information in good, readable condition. Operators should
be well trained on the operation and maintenance of the trowel.
Push the left control lever forward and pull the right control lever
backward and the trowel will rotate clockwise on approximately
a center axis. Pull the left control lever backward and push the
right control lever forward and the trowel will rotate
counterclockwise. See Table 4 on page 26 for a complete
description on the control levers directional positioning.
Look at the operator control levers. Grasp the control levers and
move them around a bit. Observe how moving the control levers
cause the gearboxes and frame to move.
Notice the foot pedal which controls the engine and blade speed.
Also take a look at the main driveline of the trowel. Take note
and reference how the belts look, this is the way the belts should
look when adjusted properly.
Constant Velocity Joints (CV-Joints)
Constant velocity joints insure the efficient transfer of power to
the drive shaft and maintain the timing of the gearboxes without
any chance of slippage.
Before using your trowel, test it on a flat watered down section of
finished concrete.This trial test run will increase your confidence
in using the trowel and at the same time it will familiarize you
with the trowel’s controls and indicators. In addition you will
understand how the trowel will handle under actual conditions.
Training
For training, please use the “TRAINING CHECKLIST” located
in the front of this manual (Page 8).This checklist is not intended
to be a substitute for proper training but will provide an outline
for an experienced operator to provide training to a new operator.
Engine
This trowel is equipped with an air cooled 27 HP Kohler gasoline
engine. Refer to the engine owner’s manual for specific
instructions regarding engine operation.This manual is included
with the trowel at the time of shipping. Please contact the STOW
parts department if a replacement manual is required.
Blades
The blades of the trowel finish the concrete as they are swirled
around the surface. Blades are classified as combination (10 or
8 inches wide) and finish (6 inches wide).This trowel is equipped
with four blades per rotor equally spaced in a radial pattern and
attached to a vertical rotating shaft by means of a spider
assembly.
Figures 2 and 3 show the location of the controls, indicators and
general maintenance parts. Each control may perform more than
one function.The functions of the controls or indicators are on
pages 20 and 21.
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — CONTROLS AND INDICATORS
1.
2.
3.
4.
Seat – Engine will neither start nor run unless operator is
8.
Choke Control Lever – In cold weather pull this lever to
seated.
start engine. After engine warms push knob all the way in.
Steering Control Levers – Directs the unit forward,
reverse, left, or right.
9.
Fuel Gauge/Filler Cap – Indicates the amount of fuel in
the fuel tank. Remove this cap to add fuel.
Retardant Spray Control Button – Sprays retardant
through the nozzle at the front of the machine.
10. FuelTank – Holds 5 gallons of unleaded gasoline.
11. Left Foot Riser – Operator foot rest pedal.
12. Spray Nozzle – Spray nozzle for retardant.
Pitch Control – Turn the crank as marked on its top surface
to increase or decrease blade pitch.
13. Right Foot Pedal – Controls blade speed. Slow blade
speed is accomplished by slightly depressing the foot pedal.
Maximum blade speed is accomplished by fully depressing
the foot pedal.
Twin Pitch Control (Option) – Both pitch towers are linked
together. One crank may be turned to adjust the blade
pitch simultaneously or individually controlled for each set
of blades.
14. EZ- Mover Boss – Front attachment point for EZ Mover.
5.
6.
7.
Light Switch –Turns on three halogen lights.Two in front
one in rear.
Used to move the trowel.
15. Dip Stick – Use to verify correct amount of engine oil.
16. Spark Plug – Access the spark plug through this cutout.
Ignition Switch – With key inserted, turn clockwise to
start engine.
Hour Meter – Indicates number of hours the engine has
run.
2
4
1
3
5
9
10
15
8
19
6
16
18
7
28
11
14
12
13
14
26
Figure 2. STR46SP Controls and Indicators (Front)
PAGE 18 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 18
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — CONTROLS AND INDICATORS
17. Safety Stop Switch – Shuts down engine when seat is
26. Spiders (Left/Right) – Consists of trowel arms, blades,
empty.
wear plate, and thrust collar.
18. Light Assembly – Optional 12 volt halogen lights are
27. Document Box – Contains all product documentation.
28. Battery – Provides +12V DC power to the electrical system.
available, two forward and one aft.
19. Lift Loops – Located on both sides of the main frame.
29. Belt Guard – Encloses drive belt used in conjunction with
Used to lift the trowel.
clutch.
20. Engine Air Filter – Protects the engine from dirt.
21. Oil Filter – Filters the engine oil.
30. Engine Oil Fill – Remove this cap to add engine oil.
22. Oil Drain – Remove the plug from end of hose to drain the
engine oil.
23. Retardant SprayTank – Holds 5 gallons of retardant.
NOTE
24. Retardant Spray Pump – Delivers retardant to the spray
nozzle.
25. EZ- Mover Boss – Rear attachment point for EZ Mover.
Read, understand, and comply with all safety messages and
operating instructions in this manual before attempting to operate
the trowel.
Used to transport the trowel.
17
27
19
15
19
18
30 20
9
24
10
28
R
E
T
A
R
D
A
N
T
O
N
L
Y
25
29
21
23
22
25
26
Figure 3. STR46SP Controls and Indicators (Rear)
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — BASIC ENGINE
3
2
8
1
7
9
10
6
11
5
4
12
Kohler 27 HP Engine
Figure 4. Engine Controls and Components
INITIAL SERVICING
5.
Oil Cooler – Helps keep engine oil cooler for longer engine
life.
The engine must be checked for proper lubrication and the fuel tank
filled with fuel prior to operation. Refer to the manufacturer's engine
manual for instructions & details of operation and servicing. The
engine shown in Figure 4 is a Kohler engine.
6. Oil Filter – Spin-on type, filters oil for contaminants.
7.
Throttle Lever – Controlled by accelerator pedal,
increases or decreases engine RPM.
1. Muffler – Used to reduce noise and emissions.
8. Oil Dip Stick – Remove to check amount and condition of
oil in crankcase.
9.
Ignition Coil – Provides spark to the ignition system.
WARNING
Enginecomponentscangenerateextremeheat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operating. NEVER operate the engine with the
muffler removed.
10. Spark Plug – Provides spark to the combustion chamber.
See engine owner's manual for plug type and gap settings.
Clean spark plug once a week.
11. Starter – Starts engine when ignition key is rotated to the
"START" position.
12. Side Oil Drain Plug (one of two) – Remove to drain
crankcase oil.
2. Oil Filler Cap – Remove to add engine oil.
3. Air Filter – Prevents dirt and other debris from entering the
fuel system. Unsnap air filter cover to gain access to filter
element.
4.
Oil Drain Hose – Remove plug from end of hose to drain
crankcase oil.
PAGE 20 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 20
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — NEW MACHINE SETUP INSTRUCTIONS
Trowel Pre-Set Up Instructions
Seat Assembly
The purpose of this section is to assist the user in setting up a
NEW trowel. If your trowel is already assembled, (seat, handles,
knobs and battery), this section can be skipped.
The seat is not installed on the trowel for shipping purposes.
To attach the seat perform the following:
The new trowel cannot be put into
service until the pre-setup installation
instructions are completed. These
pre-setup instructions only need to
be performed at the time of
There are two types of seats,
depending on what type of trowel
you have. J and B series trowels have
slots on the seat mounting plate that
allow fore and aft adjustment of the
NOTE
NOTE
unpacking a NEW trowel.
seat. H and S-series trowels have a seat that is mounted
on tracks, similar to an automobile seat.This seat can be adjusted
fore and aft via the control lever under the front of the seat.
Before packaging and shipping, this STR46 SERIES Ride-On
Power Trowel was run and tested at the factory. If there are
problems, please let us know.
1.
2.
Remove the seat from the protective wrapping.
Remove the bolts on the bottom of the seat, and place seat
on the seat mounting plate, then insert the bolts through
the holes or slots on the seat mounting plate and tighten.
Control Handle Assembly
The steering control handles are not attached to the trowel's two
lower handles at the time of shipment. To attach the steering
control handles to the two lower handle assemblies perform the
following:
Battery Setup
This trowel was shipped with a wet charged battery.This battery
may need to be charged for a brief period of time as per the
manufacturer instructions.
1.
2.
3.
4.
Remove the bolts from the plastic bag tied to the control
towers.
Remove all protective wrapping and straps from the control
handles.
CAUTION
Slip the top (loose) piece into the base of the corresponding
handle, making sure to line up the holes.
Use all safety precautions specified by the battery
manufacturer when working with the battery. See further
specific safety information on page 12 of this manual.
Install the bolt through the lined up holes and tighten the
acorn nut onto the threaded end.
To install the battery on the trowel, make sure that the battery is
well seated in the battery box. Connect the positive cable to the
positive terminal on the battery first, then connect the negative
cable to the negative terminal. Close the plastic battery box cover
and secure the battery box.
Some models are equipped with
adjustable height handles. Adjust the
height by placing the bolt through the
set of holes that corresponds to the
most comfortable height.
NOTE
5.
6.
Pay close attention to any wires that may be inside the
control handles. DO NOT pinch or cut any wires during
installation.
Inside the plastic bag of parts are two knobs for the pitch
control tower cranks. Install these two knobs onto the tower
crank levers.
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — INITIAL START-UP
The following section is intended as a basic guide to the ride-on
trowel operation, and is not to be considered a complete guide
to concrete finishing. It is strongly suggested that all operators
(experienced and novice) read “Slabs on Grade ” published by
the American Concrete Institute, Detroit Michigan.
Table 3. RecommendedViscosity Grades
DO NOT use your ride-on power trowel until this section is
thoroughly understood.
CAUTION
Gearbox Oil Level
Failure to understand the operation of the STR46SP trowel
could result in severe damage to the machine or personal
injury.
1.
Check the gearbox oil level in both gearboxes
by removing the level plug and ensuring that
the oil is at the correct level. See Figure 6.
See Figures 2 and 3 for the location of any control or indicator
referenced in this manual.
2.
Fill the gear box just to the level of the fill plug.
(Figure 6) with 69 oz. (2.041 L) of Multiquip
gearbox lubricant, p/n 20111, ISO or
equivalent.
Engine Oil Level
ALWAYS check engine oil BEFORE EACH USE.
DRAIN
PLUG
GEARBOX
VENT
1.
Pull the engine oil dipstick (Item 8, Figure 4)
FILL/LEVEL
CHECK PLUG
from its holder.
2.
Determine if engine oil is low (Figure 5).
3.
If engine oil is low, remove oil filler cap (Item 2, Figure 4),
and add correct amount of engine oil to bring oil level to a
normal safe level. The oil level should be up to, but not
over the "F" mark on the dipstick. Use oil as recommeded
in Table 3.
Figure 6. Gearbox Oil Plugs/Sight Glass
Fuel
Determine if the engine fuel is low (Figure 7). If fuel level is low,
remove the fuel filler cap and fill with unleaded gasoline.
Figure 5. Engine Oil Dipstick
DANGER
Handle fuel safely. Motor fuels are highly
flammable and can be dangerous if
mishandled. DO NOT smoke while
refueling. DO NOT attempt to refuel the ride-
on trowel if the engine is hot or running. DO
NOT attempt to start the engine until the fuel
residue has been completely wiped up and
the area surrounding the engine is dry.
To prevent extensive engine wear or
damage, always maintain the proper
oil level in the crankcase. Never
operate the engine with the oil level
below the "L" mark or over the "F"
mark on the dipstick.
NOTE
PAGE 22 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 22
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — OPERATION
5. When starting a cold engine, pull the choke knob, if so
equipped, (Figure 9) out to the closed position. In warm
weatherorwhentheengineiswarm,theunitcanbestarted
with choke halfway or completely open.
FUEL
E
F
CHOKE
KNOB
Figure 7. Fuel Gauge
CLOSED
OPEN
Important Information BeforeYou Start
1.
This ride-on trowel is equipped with a safety "safety stop
switch". This switch is located beneath the seat assembly.
Remember the engine will not start unless an operator is
sitting in the operator’s seat. The weight of an operator
depresses an electrical switch which will allow the engine
to start.
Figure 9. Choke Knob
WARNING
6.
Keep your foot OFF the blade speed control pedal and in
all circumstances, start the engine at idle (without touching
the pedal).
NEVER disable or disconnect the "safety stop switch". It is
provided for the operator's safety and injury or death may
result if it is disabled, disconnected or improperly
maintained.
7.
8.
Insert the ignition key into the ignition switch.
Turn the ignition key (Figure 10) clockwise and listen for
the engine to start. Once the engine starts release ignition
key.
2.
3.
The safety stop switch should be used to stop the engine
after every use. Doing this will verify the switch is working
properly thus providing safety for the operator.Remember
to turn the key to the “OFF” position after stopping the
machine.Not doing so will drain the battery.
9.
If the engine fails to start in this manner, consult the engine
owner's manual supplied with the trowel.
10. Test the safety stop switch by standing up briefly.The switch
under the seat should cause the engine to stop. If the switch
fails to shut down the engine.Turn off the engine with the
key switch and repair the safety stop switch. See Table 7
(Troubleshooting ) for possible causes.
The right foot pedal (Figure 8) controls blade and engine
speed.The position of the foot pedal determines the blade
speed. Slow blade speed is obtained by slightly depressing
the pedal. Maximum blade speed is obtained by fully
depressing the pedal.
OFF
START
Figure 8. Blade Speed Control Foot Pedal
Starting the Engine
1. With one foot on the ground and the other foot placed on
Figure 10. Ignition Key
the trowel's platform, grab the frame near the seat and lift
yourself onto the trowel. Sit in the operator's seat and ensure
the control handles, foot pedal and control panel items can
be comfortably accessed.
11. Let the engine idle for 3-5 minutes. If choke is applied,
push the choke to the open position as soon as the engine
will run smoothly.
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — OPERATION
Steering
5.
6.
Try adjusting the pitch of the blades.This can be done with
the ride-on trowel stopped or while the trowel is moving,
whatever feels comfortable.Test the operation of optional
equipment like retardant spray and lights if equipped.
Two control levers located in front of the operator’s seat provide
directional control for the STR46 SERIES Ride-On PowerTrowel.
Table 4 (Page 26) illustrates the various directional positions of
the joysticks and their effect on the ride-on trowel.
Pull both the left and right joysticks backward and repeat
steps 3 through 6 while substituting the word reverse for
forward.
All directional references with respect
to the steering control levers are from
the operator’s seat position.
1.
Push both the left and right control levers forward. See
Figure 11.
LEFT CONTROL LEVER
FORWARD DIRECTION
RIGHT CONTROL LEVER
Figure 11. Left and Right Control Levers
2.
3.
With your right foot quickly depress the right foot pedal
halfway.Notice that the ride-on power trowel begins to move
in a forward direction. Return both joystick controls to their
neutral position to stop forward movement, then remove
your right foot from the right foot pedal.
Practice holding the machine in one place as you increase
blade speed. When about 75% of maximum blade speed
has been reached, the blades will be moving at proper
finishing speed. The machine may be difficult to keep in
one place.Trying to keep the ride-on trowel stationary is a
good practice for operation.
CAUTION
Trowel arms can be damaged by rough handling or by
striking exposed plumbing or forms while in operation.
ALWAYS look-out for objects which might cause damage
to the trowel arms.
4.
Practice maneuvering the ride-on trowel using the
information listed in Table 4. Try to practice controlled
motions as if you were finishing a slab of concrete. Practice
edging and covering a large area.
PAGE 24 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 24
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — MAINTENANCE
Maintenance
When performing any maintenance on the trowel or engine,
follow all safety messages and rules for safe operation stated at
the beginning of this manual.
WARNING
Accidental starts can cause severe injury
or death.
ALWAYS place the ON/OFF switch in the
OFF position.
Disconnect and ground spark plug
leads and disconnect negative
battery cable from battery before
servicing.
Figure 12. Engine Service Areas
MAINTENANCE SCHEDULE
1. Oil Level Dipstick
2. Air Cleaner Cover
1.
Daily (8-10 Hours)
1. Check the fluid levels in the engine and gearboxes, fill as
Check and retighten all fasteners as necessary.
3.
Carburetor
4. Governor
necessary.
5. Oil Fill Cap (On either side)
6. #2 Valve Cover
Weekly (30-40 Hours)
1.
2.
3.
Relube arms, thrust collar and steering links.
Replace blades if necessary.
7.
8.
#2 Exhaust Port
Spark Plug, #2 side
Check and clean or replace the engine air filter as
necessary. (See following section on Air Filter
Maintenance.)
9. Oil Filter
10. Rectifier-regulator
11. Oil Drain (oil filter side)
12. Oil Drain Hose (starter side)
13. Starting Motor and Solenoid
14. Spark Plug, #1 side
15. #1 Valve Cover
4.
Replace engine oil and filter as necessary.(See following
section on Oil and Filter.)
Monthly (100-125 Hours)
1.
2.
3.
Remove, clean, reinstall and relube the arms and thrust
collar.Adjust the blade arms.
Replace gearbox lubricant after the first 100 hours of
operation.Replace every 500-600 hours thereafter.
Check drive belt for excessive wear. (Refer to following
section on Drive Belt maintenance.)
Yearly (500-600 Hours)
1.
Check and replace if necessary the arm bushings, and
thrust collar bushings, shaft seals and belts.
2.
3.
Check pitch control cables for wear.
Replace gearbox lubricant.
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — MAINTENANCE
AirCleaner(Daily)
The Kohler 27 hp engine is equipped with a replaceable, high-
density paper air cleaner element. Most are also equipped with
an oiled-foam precleaner which surrounds the paper element.
1.
Check the air cleaner daily or before starting the engine. Check
for and correct heavy buildup of dirt and debris along with loose
or damaged components.
2.
3.
4.
5.
Operating the engine with loose or
damaged air cleaner components
could allow unfiltered air into the
engine causing premature wear and
failure.
6.
7.
PrecleanerService
If so equipped, wash and re-oil the precleaner every 25 hours of
operation (more often under extremely dusty or dirty conditions).
To service the precleaner perform the following steps, refer to
Figure 13:
8.
1.
2.
3.
Release the latches located on either side of the air cleaner
cover (Figure 13), and remove the cover.
9.
Remove the foam precleaner from the paper air cleaner
element.
10.
Wash the precleaner in warm water with detergent. Rinse
the precleaner thoroughly until all traces of detergent are
eliminated. Squeeze out excess water (do not wring). Allow
the precleaner to air dry.
11.
4.
Saturate the precleaner with new engine oil. Squeeze out
all excess oil.
5.
6.
Reinstall the precleaner over the paper air cleaner element.
Reinstall the air cleaner cover and secure the latches.
12.
13.
15.
14.
Figure 13. Air Cleaner Components
PAGE 26 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 26
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — MAINTENANCE
Air Cleaner Components - See Figure 13.
Air Cleaner - Components to Check
Whenever the air cleaner cover is removed, or the paper element
or precleaner is serviced, check the following:
1. Air Cleaner Cover
2. Latch Spring
■
Air Cleaner Element Cover and Seal - Make sure the
element cover is not bent or damaged. Make sure the wing
nut, washer and seal are in place to ensure the element is
sealed against leakage.
3.
Lever Latch
4. Latch Lever Pin
5. Wing Nut
6. Inner Air Cleaner Cover
■
■
Air Cleaner Base - Make sure the base is secured tightly to
carburetor and not cracked or damaged.
7.
8.
Precleaner Element
Air Cleaner Element
BreatherTube - Make sure the tube is installed to both the
air cleaner base and the breather cover.
9. seal
10. Air Cleaner Bracket
11. Air Cleaner Base
12. Air Cleaner Base Gasket
13. Intake Manifold Gasket
14. Intake Manifold
15. screw
Disassembly and Reassembly (StandardType)
If the base plate on the standard type must be removed, proceed
as follows:
1.
2.
3.
Remove the air cleaner components as described
previously.
Paper Element Service (StandardType)
Remove the hex flange screws securing the bracket and
base.
Check the paper element every 100 hours of operation (more
often under extremely dusty or dirty conditions). Replace the
element as necessary.
Remove the base and gasket. Carefully pull the rubber
breather tube through the base
4.
5.
Remove the tube from under side of base if necessary.
Refer to the following steps and to Figure 13:
Reverse the foregoing steps to reinstall new or service
components.Tighten screw to 9.9 N-m (88 in. lb.) torque.
1.
2.
3.
4.
Release the latches located on either side of the air cleaner
cover (Figure 13), and remove the cover.
Remove the wing nut, element cover, seal and air cleaner
element.
Air Intake/Cooling System
Remove the precleaner (if so equipped) from the paper
element.
To ensure proper cooling, make sure the grass screen and fan
cooling fins and other external surfaces of the engine are kept
clean at all times.
Do not wash the paper element or use pressurized air, as
this will damage the element. Replace a dirty, bent, or
damaged element with a new element as prescribed by
the engine manufacturer.Handle new elements carefully;
do not use if the sealing surfaces are bent or damaged.
Every 100 hours of operation (more often under extremely dusty
or dirty conditions:
1.
2.
3.
Remove the blower housing and other cooling shrouds.
Clean the cooling fins and external surfaces as necessary.
Make sure the cooling shrouds are reinstalled.
5.
6.
Reinstall the seal, paper element, precleaner, element
cover, flat washer and wing nut.
Reinstall the air cleaner cover and secure the latches.
CAUTION
Operating the engine with a blocked grass screen, dirty or
plugged cooling fins, and/or cooling shrouds removed, will
cause engine damage due to overheating.
Make sure the correct depth air
cleaner element and rubber seal are
used for the engine spec. involved.
NOTE
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — MAINTENANCE
Changing Engine Oil And Filter
Oil And Fuel Lines
■
Check the oil and fuel lines and connections regularly for
leaks or damage.Repair or replace as necessary.
1. Change the engine oil after the first 5 hours of use, then
change every 6 months or 100 hours.
2.
Remove the oil filler cap (Figure 12, Item 5), and fill engine
crankcase with recommended type oil as listed inTable 3.
Fill to the upper limit of dipstick.
■
Replace the oil and fuel lines every two years to maintain the
line's performance and flexibility.
3.
Crankcase oil capacity with oil filter replacement is 2.02
qts. (1.90 liters).
Long Term Storage
■
■
■
Remove the battery.
Drain fuel from fuel tank, fuel line and carburetor.
Oil Filter (100 Hours)
Remove spark plug and pour a few drops of motor oil into
cylinder. Crank engine 3 to 4 times so that oil reaches all
internal parts.
1.
Replace the engine oil filter (Figure 14) every oil change
or 100 hours.
■
■
Clean exterior with a cloth soaked in clean oil.
Store unit covered with plastic sheet in moisture and dust-
free location out of direct sunlight.
CAUTION
Never store the ride-on trowel with fuel in the tank for any
extended period of time. Always clean up spilled fuel
immediately.
Figure 14. Oil Filter
2.
Be sure to coat the seal of the new oil filter with clean
engine oil.
Engine Tune-Up
■
See your engine manual for specific information on tuning
up your engine, checking and gaping the spark plugs, etc.
Fuel Filter (200 Hours)
■
Replace the engine fuel filter (Figure 15) every 200 hours.
See the engine manual supplied with
your machine for appropriate engine
NOTE
maintenance
schedule
and
troubleshooting guide for problems.
At the front of the book (Page 9) there is a “Daily Pre-Operation
Checklist”. Make copies of this checklist and use it on a daily
basis.
Figure 15. Fuel Filter (Typical)
Disconnect spark plug wires and battery cables before attempting
any service or maintenance on the ride-on trowel.
PAGE 28 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 28
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — MAINTENANCE
CheckingThe Drive Belt
5
The drive belt needs to be replaced as soon as it starts to show
signs of wear. Indications of excessive belt wear are fraying,
squealing when in use, belts that emit smoke or a burning rubber
smell when in use.
Under normal operating conditions, a drive belt may last
approximately 150 hours. If your trowel is not reaching this kind
of life span for drive belt wear, check the drive belt for proper
pulley alignment and spacing.
3
2
4
1
To gain access to the drive belt, remove the drive belt guard
cover (Item 1, Figure 17), then visually inspect the drive belt for
signs of damage or excessive wear. If the drive belt is worn or
damaged, replace the drive belt.
1
2
3
4
5
Drive Belt Guard Cover
Lower Pulley
Upper Pulley
Spare Drive Belt
Spare Drive Belt Holder
WARNING
DO NOT attempt to insert hands or tools
into the belt area while the engine is
running. NEVER run the engine with the
safety guards removed. Keep fingers,
hands, hair and clothing away from all
moving parts to prevent bodily injury.
Figure 17. Drive Belt Guard Cover
1.
2.
Remove Drive Belt Guard Cover (Item 1, Figure 17).
Squeeze the drive belt as shown in Figure 18, and pull the
V-belt upwards.This will spread open the faces of the lower
drive pulley.
WARNING
DO NOT remove the drive belt guard cover
until the muffler has cooled. Allow the entire
trowel to cool down before performing this
procedure.
1
2
6
Removing the Drive Belt
z
z
Leave the existing drive belt intact until instructed to cut it.
Leave the engine in place for this procedure. It is not
necessary to slide the engine to replace the drive belt.
3
5
4
z
Have a 3/4 X 1 X 3-1/4 inch wooden block available.
1
2
3
4
5
6
Upper Pulley
Drive Belt
Lower Pulley Fixed Face
Lower Pulley Spread Apart
Lower Pulley Movable Face
WOODEN BLOCK
WIDTH
1.00 IN.
LENGTH
3.25 IN.
HEIGHT
.75 IN.
Squeeze and Pull Up To Spread
Lower Pulley
Figure 18. Expanding Lower Drive Pulley
Figure 16. Wooden Block For Spacer
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — MAINTENANCE
3.
Insert the 3/4" X 1" X 3-1/4" block between the moveable
face and the fixed face of the lower drive pulley. See Figure
19. This block will help keep the lower drive pulley faces
open while installing the new drive belt.
In the event of a drive belt failure, the spare (replacement) drive belt
can be used for quick replacement at the job site to continue trowel
operation.
1.
If necessary, refer to Removing Drive Belt Instructions.
Ensure all remnants of old belt have been removed from
pulleys.
2.
To replace the drive belt with the spare drive belt, remove
the 2 bolts that secure the drive belt carrier. (Figure 20)
This will allow free movement of the belt for installation.
Take care with to not contaminate the relplacement belt
with grease or dirt.
1
Wooden Block
3.
4.
With the 3/4 x 1 x 3-1/4 wood block holding the lower pulley
open, place the replacement belt into the lower pulley first.
Work the belt over the upper drive pulley into the pulley
groove.
Figure 19. Holding Lower Pulley Open
Squeeze the belt enough to remove the wood block. With
the block removed, release the tension on the belt.
4.
If the belt is not being reused (recommended), CUT the
drive belt. Ensure all belt remnants are removed from
the pulleys.
5.
6.
Reinstall the spare belt carrier and the drive belt guard.
Replace the spare belt before the next trowel use. See
spare drive belt replacement procedures.
Installing the Drive Belt (Using Replacement Drive Belt)
The STR46SP Ride-On Power Trowel is equipped with a
replacement drive belt (spare) carrier, which is mounted on the
inboard side of the fuel tank near the clutch. Make sure that there is
ALWAYS a spare drive beltin the drive belt carrier before the trowel
is placed on a slab to finish concrete.
2
1
3
1
2
3
4
5
6
Bolt, Spare Drive Belt Carrier
Spare Drive Belt Holder
Wooden Block
CV-Joint
New Spare Drive Belt
4
5
6
Figure 20. Drive Belt Install
Lower Drive Pulley
PAGE 30 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 30
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — MAINTENANCE
5
4
6
1
2
3
1
2
3
4
5
6
CV Joint
Bolt (Remove 3 places)
New Spare Drive Belt
Bolt, Spare Drive Belt Carrier
Spare Drive Belt Holder
Left Side Gearbox
Figure 21. Spare Drive Belt Replacement
Spare Drive Belt Replacement
It will be necessary to disconnect the
3.
Once the CV-joint has been separated from the left-side
gearbox, push the CV-joint inward so that a gap exists
between the gearbox and the CV-joint (Figure 21). Slide
the spareV-belt between the gearbox coupler and the CV-
joint. Avoid contaminating the replacement belt with grease
or oil when sliding it between the CV-Joint and gearbox
coupler.
CV-Joint from the left-side gearbox
coupler.This means the removal of
the three screws that secure the CV-
Joint to the gearbox.
NOTE
To replace a spare drive belt, be prepared to disconnect the CV-
joint from the left-side gearbox. See Figure 21.
4.
5.
Place the spare drive belt inside the drive belt carrier, and
secure the spare belt carrier to the inboard side of the left
gearbox.
1.
2.
Place the trowel on suitable supports and observe all safety
precautions.
Install the three screws that secure the CV-joint to the left-
side gearbox coupler.
Remove the three screws that secure the CV-joint to the
left-side gearbox coupler.
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — MAINTENANCE
Drive SystemTheory of Operation
Centrifugal force pushes the roller arms against the ramp plate,
forcing the moveable face toward fixed face squeezing the belt. (see
Figure 24 below)
The STR46SP Ride-On Power Trowel is equipped with a "Torque
Converter"whichsuppliestorquetoboththeleftandrightgearboxes.
CENTRIFUGAL FORCE
The function of the torque converter is to automatically deliver the
correct amount of torque required by the trowel under all load
conditions.This enables the trowel to deliver the necessary torque
for float pan applications and the high rotor speeds required for
burnishing concrete.
LOW OUTPUT
SPEED
DRIVE
PULLEY
DISTANCE
MOVEABLE
FACE
MOVEABLE FACE
IS CONTROLLED
BY A SPRING
TRAVELS
AND BELT TENSION
LOW ENGINE RPM
DRIVEN PULLEY
The torque converter used in the STR46 SERIES Ride-On Power
Trowel is a variable pitch pulley type (Figure 22) connected by a
drive belt.
MOVABLE FACE IS
CONTROLLED BY
ROLLER WEIGHT ARMS
AND SPRINGS
HIGH OUTPUT
SPEED
DRIVE
PULLEY
HIGH ENGINE RPM
DRIVEN PULLEY
Fig. 24. Pulley Interaction
The"VariablePitchPulleys"haveone fixedface, andone moveable
face.The drive pulley ( torque converter, Figure 25) moveable face
is controlled by roller weight arms and springs, which change
position according to engine speed.The driven pulley moveable
face is controlled by a spring and belt tension.
DRIVE PULLEY
Fig. 22 Torque Converter/Variable Pitch Pulley
RAMP
PLATE
BUSHING
Drive Pulley
SPRING
The "Drive Pulley" uses centrifugal force (Figures 23 and 24)
to create a belt squeeze force transmitted at the pulley faces.
This condition functions as an automatic clutch and transmission.
ROLLER ARM
RI
F
T
N
U
G
A
E
L
C
F
O
WEIGHT
R
C
E
Fig. 25.Variable Pitch Pulley
FIXED
FACE
A
B
C
DRIVE
PULLEY
VARIABLE
FACE
DRIVEN
PULLEY
QUEEZE
S
T
DRIVE PULLEY
(TORQUE CONVERTER)
FORCE
BEL
NEUTRAL
LOW SPEED
HIGH SPEED
Figure 23. Torque Converter (Centrifugal Force)
Figure 26. Pulley Conditions
PAGE 32 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 32
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — MAINTENANCE
How It Works (Figure 26)
Blade Pitch
Condition A:
Condition B:
Condition C:
z
z
z
z
z
z
z
z
z
z
z
z
Engine Idling
Sometimes it may be necessary to match blade pitch between
the two sets of blades. There are some signs that this may be
necessary. For example, the differences in pitch could cause a
noticeable difference in finish quality between the two sets of
blades.Or, the difference in blade pitch could make the machine
difficult to control.This is due to the surface area in contact with
the concrete (the blade set with the greater contact area tends to
stick to the concrete more).
Drive Pulley: Small
Driven Pulley: Large
Belt: Loose and Stationary
Engine Accelerating
Drive Pulley: Small But Increasing
Driven Pulley: Large But Decreasing
Belt: ApproachingTightness
Engine At High Speed
Drive Pulley: Large
Matching Blade Pitch for Both Sets of Blades
Trowels equipped with optional Twin PitchTM Controls may need
to have blade pitch between the two sets of blades "syncronized".
If the blades need to be syncronized this is easily accomplished
by performing the following. Refer to Figure 28.
Driven Pulley: Small
Belt: Tight
1.
Lift the pitch adjustment handle on either side. Once lifted,
that side is now disconnected from the Twin PitchTM system.
Clutch
2.
3.
Adjust to match the opposite side.
When adjusted, lower the handle to Twin PitchTM operating
position.
This clutch system provides a high pulley ratio (a low gear- so to
speak) to start out and a low pulley ratio (a high gear- so to
speak) for a high speed operation, with infinite variation between
the two.
This means that it will not be necessary to give full throttle in
order to "break the blades/pans loose". The machine can slowly
be brought up to speed.
A
B
The torque-sensitive pulley (Figure 27) utilizes a spring and cam.
Peakperformanceresultsfromproperinteractionbetweenthedriven
pulley spring and the ramp angle of the cam bracket.
SPRING
DRIVEN PULLEY
CAM
BRACKET
FIXED FACE
MOVEABLE
FACE
Figure 27. Pulley Spring and Cam Bracket
A
B
Twin PitchTM disengaged (one side)
Operating Position
Figure 28. Pitch Towers
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — MAINTENANCE
Figure 30 below illustrates the "correct alignment " for a spider
plate (as shipped from the factory).
Trowel Arm adjustment Procedure
The following procedure should be
followed to adjust trowel arms when
it becomes apparent that the trowel
is finishing poorly or in need of
routine maintenance.
NOTE
A level, clean area to test the trowel prior to and after adjustement
is essential. Any unlevel spots in the floor or debris under the
trowel blades will give an incorrect perception of adjustment.
Ideally, a 5' x 5' three-quarter inch thick flat steel plate should be
used for testing.
Figure 30. Correct Spider Plate Alignment
2. Start engine, and bring trowel blades up to full speed and look
forthefollowingconditions:
■
Does the trowel have a perceived rolling or bouncing
motion?
1. To determine which blades need adjustment, place the
trowelinthetestarea(three-quarterinchthickplate)andlook
for the following conditions:
■
Does the guard ring “rock up and down” relative to the
ground?
■
Pitch the blades as flat as possible and look at the
adjustment bolts.They should all barely make contact
with the lower wear plate on the spider. If you can see
that one of them is not making contact, some adjustment
will be necessary.
Stabilizer Ring Removal
1. Ifthetrowelisequippedwithanouterstabilizerring(Figure
31), remove the four bolts at the end of each spider arm.
■
Is the machine wearing out blades unevenly (i.e. one
blade is completely worn out while the others look new)?
STABILIZER
RING
Figure 29 below illustrates "worn spider bushings or bent
trowel arms". Check to see that adjustment bolt is barely
touching (0.10" max. clearance) lower wear plate. All alignment
bolts should be spaced the same distance from the lower wear
plate.
REMOVE
TO FREE
SPIDER
ASSEMBLY
Figure 31 Stabilizer Ring
Figure 29. Worn Arm Bushings
2. Examine stabilizer ring for out of round or bends. If ring is
damaged, replace ring. If ring is found to be correct with no
damage,setaside.
PAGE 34 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 34
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — MAINTENANCE
Trowel Arm Removal
Trowel Blade Removal
1. Each trowel arm is held in place at the spider plate by a hex
head bolt (with zerk grease fitting). Remove the hex head
bolt/zerk grease fitting from the spider plate. (Figure 32)
1. Removethetrowelbladesfromthetrowelarmbyremoving
thethreehexheadbolts(Figure34)fromthetrowelarm.Set
blades aside.
2. Remove the trowel arm from the spider plate.
Figure 34. Trowel Blades
1
2
Spider Plate
Hex Head Bolt (Zerk Fitting)
2. Wirebrushanybuild-upofconcretefromallsixsidesofthe
trowel arm. Repeat this for the remaining three arms.
Figure 32. Removing
Zerk Grease Fitting
3. Should the trowel arm inserts (bronze bushing ) come out
withthetrowelarm,removethebushingfromthetrowelarm
andsetasideinasafeplace.Ifthebushingisretained inside
the spider plate, carefully remove the bushing.
4. Examinethebronzetrowelarmbushinginsert(Figure 33),
cleanif necessary.Replacebushingifout-of-roundorworn.
Figure 33. Bronze Bushings
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — MAINTENANCE
Checking Trowel Arm Straightness
3. Next, checktheclearancebetweentheroundshaftandthe
testsurfaceasoneoftheflathexsectionsofthearmrestson
thetestsurface. Rotatethearmtoeachoftheflathexsections
and check the clearance of the round shaft. Use a feeler
gauge of .005" (0.127 mm). Each section should have the
sameclearance betweentheroundofthetrowelarmshaft
andthetestsurface.
Trowel arms can be damaged by rough handling, (such as dropping
the trowel on the pad), or by striking exposed plumbing, forms, or
rebar while in operation. A bent trowel arm will not allow the trowel
to operate in a smooth fluid rotation. Ifbenttrowelarmsaresuspect,
check for flatness as follows, refer to Figures 35 and 36:
4. If the trowel arm is found to be uneven or bent, replace the
trowelarm.
Trowel Arm Adjustment
Shown in (Figure 39, Page 39) is the adjustment fixture with a
trowelarminserted.Aseachtrowelarmislockedintothefixture,
thearmboltisadjustedtowhereitcontactsastoponthefixture.
This will consistently adjust all of the trowel arms, keeping the
finisher as flat and evenly pitched as possible.
1
2
3
4
5
6
Trowel Arm Round Shaft Section
Trowel Arm Hexagonal (Hex) Shaft Section
Lever Mounting Slot (Left Arm Shown)
Roll Pin Hole
Blade Attachment Bolt Hole (One ofThree)
Flat of Hexagonal Shaft (Top of Arm)
1. LocatethetrowelarmadjustmenttoolP/N9177.
Figure 35. Trowel Arm
1. Use a thick steel plate, granite slab or any surface which is
true and flat, to check all six sides of each trowel arm for
flatness.
2. Check each of the six sides of the trowel arm (hex section).
Afeelergaugeof.004"(0.10mm)shouldnotpassbetween
theflatofthetrowelarmandthetestsurfacealongitslength
on the test surface. (Figure 36, Item 3) .
SIDEVIEW
1
2
3
4
Adjustment Bolt
"Distance"
Locking Nut
Fixture Arm
Figure 37. Trowel Arm AdjustmentTool SideView
2. Ensurethefixturearmisinthepropersetting(upordown)for
your trowel arm rotation as shown in Figure 38.
Arms with CLOCK-WISE blade
rotation use the fixture arm in the UP
1
2
3
4
Trowel Arm
FlatTest Surface
Feeler Gauge (.004 in. / 0.10 mm)
Feeler Gauge (.005 in. / 0.127 mm))
position (A in Figure 38). Arms with
NOTE
COUNTER CLOCK-WISE blade
rotation use the fixture with the fixture
arm in the DOWN position. (B in Figure
38).
Figure 36. Checking Trowel Arm Flatness
PAGE 36 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 36
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — MAINTENANCE
4. Useanallenwrenchtotightenthelockingboltssecuringthe
trowel arm in place.
5. Adjust the bolt "distance" shown in Figure 37 to match one
of the arms.The other arms will be adjusted to match this
distance.
6. Loosenthelockingnutonthetrowelarmlever,thenturnthe
trowel arm adjusting bolt until it barely touches (.010") the
fixtureadjustingbolt.
7. Oncethecorrectadjustmentismade,tightenthelocknuton
the trowel arm to lock in place.
8. Loosen locking nuts on the adjustment fixture, and remove
trowelarm.
Figure 38. Trowel Arm Adjustment Setup
9. Repeat steps for the remaining trowel arms.
3. Unscrewthelockingboltsontheadjustmenttoolandplace
thetrowelarmintothefixturechannelasshowninFigure39
Athinshimmayberequiredtocoverthebladeholesonthe
trowelarm. Makesuretoalignthetroweladjustmentboltwith
thefixtureadjustmentbolt.
Re-Assembly
1. Clean and examine the upper/lower wear plates and thrust
collar.Examine the entire spider assembly.Wire brush any
concreteorrustbuild-up.Ifanyofthespider componentsare
found to be damaged or out of round, replace them.
2. Makesurethatthebronzetrowelarmbushingisnotdamage
oroutofround.Cleanthebushingifnecessary.Ifthebronze
bushing is damaged or worn, replace it.
3. Reinstall bronze bushing onto trowel arm.
4. Repeat steps 2 -3 for each trowel arm.
5. Makesurethatthespringtensionerisinthecorrectposition
to exert tension on the trowel arm.
6. Insertalltrowelarmswithleversintospiderplate(withbronze
bushingalreadyinstalled)usingcaretoaligngreaseholeon
bronze bushing with grease hole fitting on spider plate.
1
2
3
4
5
6
7
8
9
Arm
Trowel Arm Lever
Fixture Arm
Adjustment Bolt
Distance = .010 Inch
Adjustment Bolt
Trowel Arm Adjustment Fixture
Locking Bolts
7. Locktrowelarmsinplacebytighteningthehexheadboltwith
zerk grease fitting and jam nut.
8. Re-install the blades onto the trowel arms.
9. Install stabilizer ring onto spider assembly.
10. Lubricate all grease points (zerk fittings) with premium
"Lithum 12" based grease, conforming to NLG1 Grade #2
consistency.
Shim
Figure 39. Trowel Arm Adjustment Fixture Components
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — MAINTENANCE
Installing Pans Onto Finisher Blades
1. Lift trowel just enough to slide pan under blades. Lower
finisher onto pan with blades (Item #1) adjacent to Z-Clips
(Item#4).
Theserounddiscssometimesreferredtoas"pans" attachtothe
spiders arms and allow early floating on wet concrete and easy
movement from wet to dry areas.They are also very effective in
embedding large aggregates and surface hardeners.
2. Rotate blades into position under Z-Clips. Ensure that the
bladesarerotatedinthedirectionoftravelwhenthemachine
is in operation or use the engine to rotate the blades into
position.
3. Attachthebladetie-downs(Item#3) to thefarsideoftheZ-
Clip brackets (Item #4) with tie-down knobs (Item #2) as
shown in Figure 40.
4. Check to make certain that the blade edges are secured
undertheZ-Clipsandthetie-downsaresecuredcompletely
overtheedgesofthebladebarbeforethemachineisputback
intooperation.
WARNING
ALWAYS install pans either on the work area or on an area
that is next to and level with the work area. DO NOT lift the
trowel when the pans are attached.
Decommissioning Trowel/Components
Decommissioningisacontrolledprocessusedtosafelyretirea
pieceofequipmentthatisnolongerserviceable. Iftheequipment
poses an unacceptable and unrepairable safety risk due to wear
or damage or is no longer cost effective to maintain, (beyond life-
cycle reliability) and is to be decommissioned, (demolition and
dismantlement), thefollowingproceduremusttakeplace:
Refer to Figure 40 when installing pans onto finisher blades.
1. Drainallfluidscompletely. Thesemayincludeoil, gasoline,
hydraulic oil and antifreeze. Dispose of properly in accor-
dancewithlocalandgovernmentalregulations.Neverpour
on ground or dump down drains or sewers.
2
3
2. Remove battery and bring to appropriate facility for lead
reclamation. Usesafetyprecautionswhenhandlingbatter-
ies that contain sulfuric acid, (See page 14).
3. The remainder can be brought to a salvage yard or metal
reclamationfacilityforfurtherdismantling.
1
4
1
2
3
4
BLADE ASSEMBLY
KNOB,TIE-DOWN Z-CLIP PANS
TIE-DOWN, BLADE
Z-CLIP, PAN
Figure 40. Z-Clip Finisher Pan Installation
PAGE 38 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 38
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP —TROUBLESHOOTING (ENGINE)
TABLE 5. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Fuel tank is empty.
Fill fuel tank.
Shut-off valve is closed.
Fuel line has suction leak or
Open fuel shut-off valve.
Check fuel line condition and fuel line clamps.
is restricted. Fuel filter, or fuel Ensure that fuel line is not kinked. Check fuel filter
tank cap vent is obstructed.
for restriction and replace if necessary. Check fuel
cap vent and clean or replace as necessary.
Fuel supply is contaminated. Drain and clean fuel tank, clean tank and refill with
fuel.
Engine Cranks But
Will Not Start
If carbureted, carburetor is
underchoked or overchoked.
Apply recommended amount of choke for cold and
warm weather.
Spark plug is fouled,
improperly gapped, or
damaged. Spark plug leads
disconnected.
Check spark plug for fouling, check gap, and
inspect for damage. Clean or replace spark plug
as necessary. Reattach spark plug leads if
disconnected.
Safety stop switch
malfuntion.
Ensure that the Safety Stop Switch is functioning
when the operator is seated; replace switch if
necessary.
Fuel tank is empty.
Fill fuel tank.
Shut-off valve is closed.
Open fuel shut-off valve.
Fuel line has suction leak or
is restricted. Fuel filter is
obstructed, or fuel tank cap
vent is blocked.
Check fuel line condition and fuel line clamps.
Ensure that fuel line is not kinked. Check fuel filter
for restriction and replace if necessary. Check fuel
cap vent and clean or replace as necessary.
Engine Starts But
Will Not Continue
Running
If engine is carbureted,
Apply recommended amount of choke for cold and
carburetor is underchoked or warm weather.
over choked.
Faulty ignition switch or
starter.
Replace defective switch or starter.
Engine is seized.
Repair or replace engine.
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP —TROUBLESHOOTING (ENGINE)
TABLE 5 CONT.. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Air filter is obstructed.
Replace air filter.
Altitude causes 3% loss of
horsepower per 1000 feet of
altitude.
If available, install high altitude jets in carburetor.
Choke is partially closed.
Open choke.
Faulty spark plugs or spark
plug leads. Spark plug lead
disconnected.
Replace spark plugs or spark plug leads if faulty.
Reattach spark plug lead if disconnected.
Engine Lacks
Power
Fuel is contaminated.
Drain and clean fuel tank. Refill with clean fuel.
There is a lack of lubrication. Check engine oil.
Engine is overheated
Allow engine to cool. Find and repair cause of
overheating.
Exhaust is restricted.
Remove or repair restriction.
Ignition timing incorrect.
Set engine ignition timing to manufacturer's
specification.
Ignition timing incorrect.
Fuel mixture is too lean.
Exhaust is restricted.
Set engine ignition timing to manufacturer's
specification.
Look for intake system leak. Repair any leaks
found.
Remove or repair restriction.
Replace fan shroud.
Engine Overheats
Fan shroud or fan is broken
or missing.
Coolant level is low.
Fill radiator when cool. Add coolant to fill line on
reservoir.
Low or Hi crankcase oil level
Check engine oil. Fill if low, drain if overfilled.
Charge and test battery. Replace if defective.
Battery is discharged or
defective.
Loose or faulty wires or
connections.
Inspect wiring, repair any bad connections or
wires.
Engine Will Not
Crank
Faulty ignition switch or
starter.
Replace defective switch or starter.
Engine is seized.
Repair or replace engine.
PAGE 40 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 40
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP —TROUBLESHOOTING (TROWEL)
TABLE 6. TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Make sure that the Safety Stop Switch is functioning when the
operator is seated; replace switch if necessary.
Safety Stop Switch malfunction?
Look at the fuel system. Make sure there is fuel being supplied to
the engine. Check to ensure that the fuel filter is not clogged.
Fuel?
Engine running rough or not
at all.
Check to ensure that the ignition switch has power and is
functioning correctly.
Ignition?
Other problems?
Consult engine manufacturer’s manual.
Check wiring. Replace as necessary.
Loose wire connections?
Safety Stop Switch not
functioning.
Bad contacts?
Blades?
Replace switch.
Make certain blades are in good condition, not excessively worn.
Finish blades should measure no less than 2" (50mm) from the
blade bar to the trailing edge, combo blades should measure no
less that 3.5" (89mm). Trailing edge of blade should be straight
and parallel to the blade bar.
Check that all blades are set at the same pitch angle as
measured at the spider. A field adjustment tool is available for
height adjustment of the trowel arms (see Optional Equipment).
Spider?
Check the spider assembly for bent trowel arms. If one of the
arms is even slightly bent, replace it immediately.
Bent trowel arms?
Check the trowel arm bushings for tightness. This can be done by
moving the trowel arms up and down. If there is more than 1/8"
(3.2 mm) of travel at the tip of the arm, the bushings should be
replaced. All bushings should be replaced at the same time.
If trowel “bounces, rolls
concrete, or makes uneven
swirls in concrete”.
Trowel arm bushings?
Check the flatness of the thrust collar by rotating it on the spider.
If it varies by more than 0.02" (0.5 mm) replace the thrust collar.
Thrust collar?
Check the thrust collar by rocking it on the spider. If it can tilt
more than 1/16" (1.6 mm) [as measured at the thrust collar O.D.],
replace the bushing in the thrust collar.
Thrust collar bushing?
Check the thrust bearing to see that it is spinning free.
Replace if necessary.
Thrust bearing worn?
Blade pitch?
Check blades for consistent pitch. Adjust per Maintenance section
instructions if necessary.
The main output shaft of the gearbox assembly should be
checked for straightness. The main shaft must run straight and
cannot be more than 0.003" (0.08 mm) out of round at the spider
attachment point.
Main shaft?
Yoke?
Machine has a perceptible
rolling motion while running.
Check to make sure that both fingers of the yoke press evenly on
the wear cap. Replace yoke as necessary.
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP —TROUBLESHOOTING (TROWEL)
TABLE 6. TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Check all electrical connections, including the master on/off switch
and check to see if wiring is in good condition with no shorts.
Replace as necessary.
Wiring?
Lights not working.
Lights?
Check to see if light bulbs are still good. Replace if broken.
Check the tank to make sure retardant is present. Fill tank as
necessary.
Retardant?
Check all electrical connections, including master on/off switch
connections. Replace components and wiring as necessary.
Wiring?
Retardant spray not
working.
Check the continuity of master on/off switch. Replace if broken.
Bad switch?
If pump has a voltage present when the switch is turned on, but
does not operate and electrical connections to the pump are
good, replace the pump.
Bad spray pump?
Worn components?
Check for wear of steering bearings and linkage components
replace if necessary.
Steering is unresponsive.
Check to ensure free movement at pivot bushings.
Adjust seat with lever located on the front of the seat.
Pivots?
Operating position is
uncomfortable.
Seat adjusted for operator?
Make sure that both crank handles are pushed down as far as
possible. Doing this ensures that the linkage is engaged.
Crank handles?
Broken part?
Linkage on Twin Pitch not
working.
Replace all broken parts immediately.
PAGE 42 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 42
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — NOTES
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and remarks QTY. Column
used in the Parts section of this manual. Use the help numbers
found on the back page of the manual if there are any questions.
Numbers Used - Item quantity can be indicated by a number,
a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
The contents and part numbers listed in the parts section are
subject to change without notice. Multiquip does not
guarantee the availibility of the parts listed.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
REMARKS Column
Sample Parts List:
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.
NO. PART NO. PART NAME
QTY. REMARKS
1
2
2
3
4
12345
BOLT ....................... 1.... INCLUDES ITEMS W/
WASHER, 1/4 IN. ........... NOT SOLD SEPARATELY
WASHER, 3/8 IN. .... 1.... MQ-45TONLY
HOSE .................... A/R.. MAKE LOCALLY
BEARING ................ 1.... S/N2345B AND ABOVE
*
*
*
12347
12348
12349
Assembly/Kit - All items on the parts list with the same unique
symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
NO. Column
Unique Symbols - All items with same unique symbol
Serial Number Break - Used to list an effective serial number
range where a particular part is used.
( , #,
+
, %, or >) in the number column belong to the same
*
assembly or kit, which is indicated by a note in the “Remarks”
column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general item,
such as different size saw blade guards in use or a part that
has been updated on newer versions of the same machine.
Specific Model Number Use - Indicates that the part is used
only with the specific model number or model number variant
listed. It can also be used to show a part is NOT used on a
specific model or model number variant.
When ordering a part that has more
than one item number listed, check
the remarks column for help in
determining the proper part to order.
NOTE
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
PART NO. Column
Numbers Used - Part numbers can be indicated by a number,
a blank entry, orTBD.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
TBD (To Be Determined) is generally used to show a part that
has not been assigned a formal part number at time of
publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
PAGE 44 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 44
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — SUGGESTED SPARE PARTS
Qty.
10
1
P/N
Description
STR46SP KOHLER ENGINES
10031 .................... WASHER 1/4 IN.
12548 .................... SPRAY PUMP
1 Unit
1
392292 .................. SPRAY NOZZEL
1
2108 ...................... CAP, SPRAYTANK
Qty.
4
P/N
Description
1
2673 ...................... CIRCUIT BREAKER 30A, 12V
4682 ...................... TOGGLE SWITCH
21495 ............TROWEL ARM, LH
2829 ..............TROWEL ARM, RH
11903 ............LEVERTROWEL ARM (L.S.)
11904 ............LEVERTROWEL ARM (R.S.)
20938 ............THRUST COLLAR KIT
12785 ............SPIDER KIT
1
4
1
8381 ...................... BOOT, TOGGLE SWITCH
12005 .................... ENGINE-OFF SAFETY SWITCH
12018 .................... CONNECTOR, RELAY
12017 .................... RELAY, ENGINE-OFF SWITCH
2405002S.............. FUEL FILTER, PRIMARY, 27 HP
2405010S.............. FUEL FILTER, SECONDARY, 27 HP
0450905002 .......... FUEL FILTER, CANNISTER 28 HP
2439320S.............. FUEL PUMP, 28 HP
4
1
4
1
2
1
2
1
20
20
20
4
0166 A ...........WASHER
1
1876 ..............JAM NUT
1
0164 B ...........SCREW
1
11039 ............BUSHING
1
2408303S.............. ELEMENT, AIR FILTER 27/28 HP
2408303S.............. ELEMENT, PRE-CLEAN 27/28 HP
5205002S.............. OIL FILTER, 27HP
4
4
11595 ............SPRING (L.S.)
1
11594 ............SPRING (R.S.)
1
20
20
20
4
1875 ..............WASHER
1
1205001S.............. OIL FILTER, 28, HP
1322 ..............SCREW ASSY, ARM RETAINING
1162 A ...........CAP GREASE FITTING
0131 A ...........SCREW (HHC 1/4 - 20 X 3/4)
0948 ..............WASHER, FLAT
2
2513212S.............. SPARK PLUG, 27 HP
2
1213202S.............. SPARK PLUG, 28 HP
1
20138 .................... BELT, CVT-COMET
4
1
1
5475521S.............. REGULATOR, RECTIFIER 27HP
2540308S.............. REGULATOR, RECTIFIER 28HP
20138 ............BELT, DRIVE CVT
0181 B ...........WASHER 1/4 IN
11418 ............FUEL CAP/GAUGE (ENG)
19633 ............BUSHING, RUBBER FUEL
2124 ..............CABLE, THROTTLE (FOOT PEDAL)
1
20
1
1
1
1
2153 ..............ROD END, FEM RH (THROTTLE CABLE)
11143 ............ROD END, FEM RH 1/2 - 20 (STEERING)
2063 ..............ROD END, MALE RH 3/8 - 24 (STEERING)
11142 ............ROD END, MALE RH 1/2 - 20 (STEERING)
6
4
2
4
......................BLADE ASSY.CONTACT UNIT SALES DEPT/ ACCESSORY ITEM
Part numbers on this Sug-
gested Spare Parts List may
supersede/replace the P/N
shown in the text pages of
this book.
NOTE
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
PAGE 46 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 46
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
NO.
1
PART NO.
PART NAME
QTY.
REMARKS
11246
DECAL SET, INTERNATIONAL STDS ...................1............. INCLUDES ITEMS W/
*
1A
DECAL, BELT DRIVE
DECAL, GEAR DRIVE
DECAL, CHECK OIL
DECAL, HOT SURFACE
DECAL, LIFT POINT
1
1
1
1
1
1
1
1
1
1
1
1
2
2
*
1B
1C
1D
1E
1F
*
*
*
*
DECAL, LUBRICATION
*
1G
DECAL, CLOCKWISE ROTATION
DECAL, COUNTER-CLOCKWISE ROTATION
DECAL, POWDER COATED
DECAL, STOW
DECAL, AL PITCH RH
DECAL, AL PITCH LH
DECAL, SPRING SAFETY
DECAL, MQ-WHITEMAN RED/TOWER
DECAL, SAFETY CLOTHING ISO BLUE ...............1............. REPLACES 11247
DECAL, CONTROL PANEL
DECAL, STR46 SERIES
SERIAL PLATE.......................................................1............. CONTACT PARTS DEPT.
DECAL, READ OPERATOR'S MANUAL
DECAL, “CE”
DECAL, ROTATING BLADE HAZARD
DECAL, WARNING “PROP 65”
DECAL, LIFTING, CRUSH HAZARD STX-55J6
DECAL, VENTILATION 2XFWRSDPU
*
*
1H
2
3
13118
11111
2300
2332
2634
1499
36099
2814
TBD
4
5
6
7
8
9
10
11
12
13
14
15
16
17
1
1
35137
11092
35168
20525
21455
36090
1
1
2
1
1
1
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — PIVOT ASSY. (RIGHT/LEFT)
PIVOT ASSY. (RIGHT/LEFT)
PAGE 48 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 48
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — PIVOT ASSY. (RIGHT/LEFT)
PIVOT ASSY. (RIGHT/LEFT)
NO.
1
2
3
4
5
6
7
8
PART NO.
1023
0166 A
2304
PART NAME
QTY.
16
20
4
1
4
1
4
2
2
1
2
1
4
REMARKS
SCREW, HHC 3/8 - 16 X 1-1/4
WASHER, LOCK, 3/8 MED.
ROCKER BLOCK WITH BUSHING
PIVOT, DOUBLE ROCKER
SCREW, SHS 5/16 - 18 X 5/16
ARM, PIVOT RIGHT
2146
10138
12412
4196
5054 A
8136
12413
2312
2145
SCREW, HHC 3/8 - 16 X 3/4
WASHER, LOCK 1/2 MED
SCREW, HHC 1/2 - 20 X 1-1/2
ARM, PIVOT LEFT
ROCKER BLOCK, WITH SET
PIVOT JOINT, SINGLE ROCKER
SCREW, FHSC 3/8 - 16 X 1
PLATE, GEARBOX ADAPTOR
9
10
11
12
13
14
1394
11248
2
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — STEERING HANDLES ASSY. (RIGHT/LEFT)
STEERING HANDLES ASSY. (RIGHT/LEFT)
PAGE 50 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 50
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — STEERING HANDLES ASSY. (RIGHT/LEFT)
STEERING HANDLES ASSY. (RIGHT/LEFT)
NO.
1
2
3
4
PART NO.
0189
11142
11177-1
2197
PART NAME
QTY.
1
3
2
2
REMARKS
GRIP, HANDLE LT
ROD END, 1/2 - 20 MALE RH
HANDLE, TUBE
NUT, ACORN, 1/4 - 20
5
6
7
8
5277
SCREW HHC 1/4 - 20 X 1-1/2
HANDLE, STEERING, LOWER
SPACER, ROD END
ROD END, 1/2 - 20 FEMALE RH
THREADPIECE, 1/2 - 20 X 2 PLTD
NUT, HEX JAM 1/2 - 20
SCREW, SHC 1/2 - 20 X 2 PLTD
NUT, NYLOC 3/8 -16
2
2
5
3
1
5
1
8
1
1
1
1
3
2
8
16
2
12425-1
11141
11143
11173
11146
11144
10133
11145
0131 A
11205
10024
0447
12426
1023
10136
2219
10176
12193
2267
EM963105
8151
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
SCREW, SHC 1/2 -20 X 3 PLTD
SCREW HHC 1/4 - 20 X 3/4
ROD, L/R MOTION
NUT, NYLOC 1/4 - 20
WASHER, FLAT 1/2 SAE
NUT, SLOTTED 3/4 - 16 PLTD
SCREW, HHC 3/8 - 16 X 1-1/4 GR5
WASHER, FLAT SAE 3/8
PIN, COTTER 1/8 X 1-1/2
NUT, NYLOC 1/2 - 13
LEVER, L/R CONTROL
GRIP, HANDLE RT
SCREW, HHC 1/2 - 13 X 2 .....................................3.................. REPLACES 6159 A
2
1
1
WASHER, FLAT SAE 3/4
4
1
1
4
4
4
4
12374-1
12375-1
0735
0735 A
11149
11138
STEERING CONTROL RS ASSIST
STEERING CONTROL LS ASSIST
BEARING CUP, TIMKEN #A6157
BEARING CONE TIMKEN #A6075
BEARING, SB-204-12
BEARING HSG, P-BLOCK 47MPB(2PC)
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — STEERING ASSIST CONTROL ASSY. (RIGHT/LEFT)
STEERING ASSIST CONTROL ASSY. (RIGHT/LEFT)
PAGE 52 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 52
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — STEERING ASSIST CONTROL ASSY. (RIGHT/LEFT)
STEERING ASSIST CONTROL ASSY. (RIGHT/LEFT)
NO.
1
2
PART NO.
11146
11142
PART NAME
NUT, HEX JAM 1/2 -20 PLTD
ROD END, 1/2 - 20 MALE RH
QTY.
6
6
REMARKS
3
4
5
6
EM963105
10176
12200
SCREW, HHC 1/2 -13 X 2 ....................................10 .................. REPLACES 6159 A
NUT, NYLOC 1/2 -13
STEERING ASSIST ASSEMBLY
WASHER, FLAT 1/2 SAE
10
2
0447
8
7
8
9
10
11
12
13
11143
5054 A
8136
11127-1
0131 A
11150
ROD END, 1/2 - 20 FEMALE RH
WASHER, LOCK 1/2 MED
SCREW, HHC 1/2 - 20 X 1-1/2
LEVER, STEERING CONTROL
SCREW/ HHC 1/4 - 20 X 3/4
BEARING, SB-201 - 8
4
2
2
2
12
6
6
11139
HOUSING SET, BEARING FLANGE 40M-2
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — GEARBOX ASSY. (RIGHT)
GEARBOX ASSY (RIGHT)
PAGE 54 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 54
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — GEARBOX ASSY. (RIGHT)
GEARBOX ASSY (RIGHT)
NO.
PART NO.
12906
5031 A
0948
12981
12765
0121 A
10989
12908
1132
12583
9045
0232 A
2309
PART NAME
QTY.
REMARKS
1%
SHAFT, GEARBOX INPUT W/FAN
SCREW, RHM 1/4-20 X1/2
WASHER, FLAT, 1/4 SAE
SHROUD, GB FIN COVER, RIGHT
1
4
5
1
2
%
3
%
4
%
5
%
GEAR BOX HD RIDER 1-1/4 SHAFT .....................1.................. HOUSING ONLY
FITTING, PLUG 3/8MP SQUARE HEAD
STUD, N10 - 32 X 3/4
6
%
3
1
1
1
1
2
2
2
7
%
8
%
RIGHT HANDWORM
VENT, AIR
SPACER, X 11D X 1.168L
BEARING, CONE TIMKEN #1986
BEARING, CUP, TIMKEN #1932
O-RING, 2 -13/16”VINTON
9
%
10%
11
12
13+
14+
%
%
%
%
*
*
GASKET, RED........................................................1.................. SOLD AS KIT ONLY
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
%
%
2307
FLANGE, COUNTERSHAFT
WASHER, EXT SHKP 1/4
SCREW, HHC 1/4-20 X 7/8
SEAL, OIL, NATIONAL #471689V
FAN, RIGHT (CW)
SCREW, HHC 1/4-20 X 1
SCREW, HHC, WASHER 10-32 X 1/2
WASHER, FLAT #10 SAE
NUT, NYLOC 10-32
2
8
8
2
1
1
1
4
1
1
TBD
%
%
%
%
%
%
%
%
2295
12909
10921
0730
19477
2203
10019
10894
12788
2618
RIGHT-SIDE FAN COVER
GEAR BOX ASSY., COMPLETE RIGHT-SIDE.......1.................. INCLUDES ITEMS W/
GASKET KIT ..........................................................1.................. INCLUDES ITEMS W/+
BEARING KIT ........................................................1.................. INCLUDES ITEMS W/
SCREW, FHSC 3/8 - 24 X 3/4 PLAIN
RETAINER, DRIVEN PULLEY
COUPLER - 7/8” ID
KEY, 1/4 X1/4 X13/16
SCREW, SHS 10-32 X1/4
KEY, WOODRUFF #21 HARDENED
SEAL, 1-1/4 DIA NAT # 471766V
SCREW, FHS 5/16 -18 X 1
RING, SNAP TRUARC #5100 - 125
COVER, HD GEARBOX 1-1/4 SHAFT
O-RING, A - 264 VITON
%
%
%
%
%
%
%
%
12833
1313
*
1
1
1
1
1
1
1
4
1
1
1
2
2
1
1
1
9120
2048
2323
10450
1139
34+
%
12769
20875
12770
12766
9038
35
36
37
%
%
%
38+
39
%
%
%
12767
12768
12764
9180
BEARING, CUP, TIMKEN #15245
BEARING, CONE TIMKEN #15126
SHAFT, MAIN HD RIDER 1-1/4 SHAFT
KEY, 5/16 X 2 -1/4 HRDND
*
%
%
%
40
*
41
42
43
12772
GEAR, WORM RH. HT 1-1/4
44+
45+
46+
47+
48+
%
%
%
%
%
GASKET, RED........................................................1.................. SOLD AS KIT ONLY
GASKET, GREEN ..................................................1.................. SOLD AS KIT ONLY
GASKET, BLUE ......................................................1.................. SOLD AS KIT ONLY
GASKET, BROWN..................................................1.................. SOLD AS KIT ONLY
GASKET, YELLOW.................................................1.................. SOLD AS KIT ONLY
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — GEARBOX ASSY. (LEFT)
GEARBOX ASSY (LEFT)
PAGE 56 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 56
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — GEARBOX ASSY. (LEFT)
GEARBOX ASSY (LEFT)
NO.
PART NO.
12906
5031 A
0948
12982
12765
0121 A
10989
12907
1132
12583
9045
0232 A
2309
PART NAME
QTY.
REMARKS
1%
SHAFT, GEARBOX INPUT W/FAN
SCREW, RHM 1/4-20 X1/2
WASHER, FLAT, 1/4 SAE
SHROUD, GB FIN COVER, LEFT
1
4
5
1
2
%
3
%
4
%
5
%
GEAR BOX HD RIDER 1-1/4 SHAFT .....................1.................. HOUSING ONLY
FITTING, PLUG 3/8MP SQUARE HEAD
STUD, N10 - 32 X 3/4
6
%
3
1
1
1
1
2
2
2
7
%
8
%
LEFT HAND WORM
VENT, AIR
SPACER, X 11D X 1.168L
BEARING, CONE TIMKEN #1986
BEARING, CUP, TIMKEN #1932
O-RING, 2 -13/16”VINTON
9
%
10%
11
12
13+
14+
%
%
%
%
*
*
GASKET, RED........................................................1.................. SOLD AS KIT ONLY
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
%
%
2307
FLANGE, COUNTERSHAFT
WASHER, EXT SHKP 1/4
SCREW, HHC 1/4-20 X 7/8
SEAL, OIL, NATIONAL #471689V
FAN, LEFT (CCW)
SCREW, HHC 1/4-20 X 1
SCREW, HHC, WASHER 10-32 X 1/2
WASHER, FLAT #10 SAE
NUT, NYLOC 10-32
2
8
8
2
1
1
1
4
1
1
TBD
%
%
%
%
%
%
%
%
2295
12909
10922
0730
19477
2203
10019
10893
12789
2618
LEFT-SIDE FAN COVER
GEAR BOX ASSY., COMPLETE LEFT-SIDE .........1.................. INCLUDES ITEMS W/
GASKET KIT ..........................................................1.................. INCLUDES ITEMS W/+
BEARING KIT ........................................................1.................. INCLUDES ITEMS W/
SCREW, FHSC 3/8 - 24 X 3/4 PLAIN
RETAINER, DRIVEN PULLEY
COUPLER - 7/8” ID
KEY, 1/4 X1/4 X13/16
SCREW, SHS 10-32 X1/4
KEY, WOODRUFF #21 HARDENED
SEAL, 1-1/4 DIA NAT # 471766V
SCREW, FHS 5/16 -18 X 3/4
RING, SNAP TRUARC #5100 - 125
COVER, HD GEARBOX 1-1/4 SHAFT
O-RING, A - 264 VITON
%
%
%
%
%
%
%
%
12833
1313
*
1
1
1
1
1
1
1
4
1
1
1
2
2
1
1
1
9120
2048
2323
10450
1139
34+
%
12769
20875
12770
12766
9038
35
36
37
%
%
%
38+
39
%
%
%
12767
12768
12764
9180
BEARING, CUP, TIMKEN #15245
BEARING, CONE TIMKEN #15126
SHAFT, MAIN HD RIDER 1-1/4 SHAFT
KEY, 5/16 X 2 -1/4 HRDND
*
%
%
%
40
*
41
42
43
12771
GEAR, WORM LH. HT 1-1/4
44+
45+
46+
47+
48+
%
%
%
%
%
GASKET, RED........................................................1.................. SOLD AS KIT ONLY
GASKET, GREEN ..................................................1.................. SOLD AS KIT ONLY
GASKET, BLUE ......................................................1.................. SOLD AS KIT ONLY
GASKET, BROWN..................................................1.................. SOLD AS KIT ONLY
GASKET, YELLOW.................................................1.................. SOLD AS KIT ONLY
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — SINGLE PITCH HANDLE ASSY. (RIGHT/LEFT)
SINGLE PITCH HANDLE ASSY. (RIGHT/LEFT)
PAGE 58 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 58
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — SINGLE PITCH HANDLE ASSY. (RIGHT/LEFT)
SINGLE PITCH HANDLE ASSY. (RIGHT/LEFT)
NO
PART NO
PART NAME
CRANK KNOB
SPACER
CRANK LEVER
HARDENEDWASHER
SHOULDER BOLT
QTY.
REMARKS
1#%+ 4403
2#%+ 3231
3#%+ 2575
4#%+ 1733
5#%+ 1616
2
2
2
2
2
6#%
7#%
8#%
9#%
10#%
11#%
12#%
13#
14#
15#
16#
17#
18#
19#
20#
21#
22#
23#
24#
25#
26#
27#
28#
29#
30
2737
2621
1162A
4014
2332
2300
0185
1617
2170
1604
1111
2367
2169
10646
10382
10721
10723
12460
1116
10548-1
0202
0300B
5283
KNOB KIT ...................................................................2........... INCLUDES ITEMS W/+
FITTING GREASE
2
2
4
1
1
2
CAP, GREASE ZERK #2
SCREW, 2-3/16 P-K TYPE U DRIVE
DECAL, AL PITCH, LH
DECAL, AL PITCH, RH
SCREW, SHSS 3/8-16 X 3/8"
LEVER ASSY, TROWEL ADJUSTMENT....................2........... INCLUDES ITEMS W/%
BEARING, RACE, TORR. #TRA1220
BEARING, BALL THRUST E5 AETNA
BEARING, ALUM.
COLLAR, SET .75 X 1.25 X .56, 2 SET SCRW
BEARING,THRUST, TORR.#NTA1220
SHAFT, SPC CONTROL
BOLT, SHOULDER, 3/8 X 3/8 LONG
SLIDE BLOCK
ROLL PIN
CABLE ASSEMBLY 26.38"
BRASS JAM NUT
PITCH CONTROLTUBE
SCREW, HHC 5/16-18
FLAT WASHER 5/16"
6
2
2
2
2
2
2
2
2
2
4
2
8
8
8
2
LOCK NUT 5/16-18
SNAP RING
10512
11109-1
PITCH ASSY...............................................................2........... INCLUDES ITEMS W/#
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — DRIVE ASSY.
DRIVE ASSY.
PAGE 60 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 60
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — DRIVE ASSY.
DRIVE ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
21494
20186
300518C
0126
2090
1146
DRIVE ASSEMBLY, W/COMET.......................................1............ INCLUDES ITEMS W/
*
2
3
PLATE, BEARING MOUNT
KEY, 1/4 X 3/16 X 3"
KEY, WOODRUFF #9
RING, SNAP TRUARC #5100 - 106
SCREW, FHSC 5/16 - 18 X 1 NYLOC
WASHER, RETAINING
2
1
4
4
2
2
1
2
1
4
4
1
1
1
1
1
3
*
*
4
5
*
*
6
7
*
2037
2029
*
8
9
COUPLER, 1 ID. RIDER
*
10337
20044
10136
10133
21475
20043
20116
21491
12590
20056
2052
11108
1662
0243
0161 C
2074
2259
BEARING, PILLOW BLOCK FAF YAK- 1
SPACER, BEARING SHAFT
WASHER, FLAT 3/8 SAE
NUT, NYLOC 3/8 - 16
PULLEY, CVT LOWER COMET 302538C
SHAFT, DRIVE BEARING
O-RING, SIZE- 031 BUNA
PANEL, SPLASH RIGHT
COUPLER, CV JOINT COMET CLUTCH
SCREW, HHC 1/4 - 28 X 3/4 GRD. 8
JOINT, CV W/BOOT ........................................................ 4............ INCLUDES ITEM W/%
GASKET, CV JOINT BOOT
TIE WRAP, BLACK
SCREW, SHC 5/16 - 18 X 1-3/4
WASHER, LOCK, 5/16 MEDIUM
SHAFT, CV JOINT, 9.13 LG
BOOT, CV JOINT
SCREW, SHC 5/16 -18 X 2 -1/4 PLTD
SHAFT, CV JOINT 10.81 LG
SCREW, HHC 3/8-16 X 1-1/2 SS
KEY, 3/16 X 11/16
*
10
*
11
*
12
*
13
*
14
*
15
*
16
*
17
*
18
*
19
*
20
*
4
4
3
12
1
4
9
1
4
1
21
*
22
*
23
*
24
*
25 %
*
26
*
2186
27
*
10748
20187
10909
28
*
29
*
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — ENGINE/MUFFLER/BELT ASSY.
ENGINE/MUFFLER/BELT ASSY.
PAGE 62 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 62
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — ENGINE/MUFFLER/BELT ASSY.
ENGINE/MUFFLER/BELT ASSY.
NO.
1
2
3
4
5
7
8
9
10
11
12
13
15
16
17
18
29
20
21
22
PART NO.
M841080S
2404149S
2507204S
M650012S
2431404S
2406836S
2412690S
M839020S
21421
PART NAME
QTY.
4
2
4
4
1
1
1
2
1
4
4
8
1
1
1
1
REMARKS
NUT, FLANGE MUFFLER
GASKET, EXHAUST MANIFOLD
STUD, EXHAUST
SCREW, HEX FLANGE
INNER HEAT SHIED, MUFFLER
MUFFLER, O.F. SIDE OUTLET
BRACKET, MUFFLER
SCREW, HEX FLANGE
ENGINE, KOHLER 27HP
SCREW, HHC 5/16 -18 X 1-3/4
WASHER, FLAT 5/16 SAE
WASHER, LOCK 5/16 MED
KEY, 0.25 SQ X 2.75
1207
0300 B
0161 C
20444
20138
20846
21528
4703
21316
5283
BELT, CVT - COMET
CLUTCH, 1 - 7/16 CVT COMET
SPACER, 1.415 O.D. X .66 I.D. X 1.5 L
WASHER, LOCK, 5/8 MED
SCREW, HHC 5/8 - 18 X 3
NUT, NYLOC 5/16 - 18
1
1
4
1
21489
WASHER, FLAT 1.437 X .032 THK
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — AIR CLEANER/OIL FILTER/OILCOOLER ASSY.
AIR CLEANER/OIL FILTER/COOLER ASSY.
PAGE 64 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 64
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — AIR CLEANER/OIL FILTER/OILCOOLER ASSY.
AIR CLEANER/OIL FILTER/COOLER ASSY.
NO.
PART NO.
5475501S
2534104S
2415320S
2409667S
1210001S
2409601S
230046S
2408305S
2408303S
2408653S
2412688S
2409437S
2404106S
2655
PART NAME
QTY.
REMARKS
1
KIT, KNOB W/SEAL ........................................ 1.................. INCLUDES ITEMS W/
*
2
*
3
*
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
KNOB, AIR CLEANER COVER
O-RING
COVER, AIR CLEANER
WINGNUT
COVER, INNER AIR CLEANER
SEAL BREATHER
ELEMENT, PRE-CLEANER
ELEMENT, AIR FILTER
SCREW, HEX. FLANGE M6X1.0X16
BRACKET, AIR CLEANER BASE
BASE, A/C W/STRTR SIDE DIMPLE
GASKET, AIR CLEANER BASE
HOUR METER
RIVET, POP 1/8 DIA X .400 ALUMINUM
SPARK PLUG
FILTER, OIL
1
1
1
1
1
1
1
1
2
1
1
1
1
2
2
1
1
1
1
1
2
1
8239
2513212
5205002S
19317
TBD
370628
60045
1947
12237
5475521S
PLUG, OIL DRAIN
FITTING, 90 DEGREE
FITTING, BRASS 45 6 BARB 1/4MP
HOSE, 3/8 ID PUSHLOCK
CLAMP, HOSE WORM 1/4 - 5/8
FITTING, PUSH-ON 6 HOSE 6MJ
ALUMINUM BASE OIL COOLER ................... 1.................. INCLUDES ITEMS W/#
24A# 2813601S
24B# 2415321S
NIPPLE, OIL FILTER
O-RING, OIL COOLER
REGULATOR, RECTIFIER
FITTING, CAP 6F JHEX
BRACKET, AIR CLEANER
GASKET, AIR CLEANER BASE
MANIFOLD, INTAKE ....................................... 1.................. INCLUDES ITEMS W/%
GASKET, CARBURETOR
O-RING, INTAKE PORT
SCREW, HEX. FLANGE M6X1.0X40
1
1
1
1
1
1
25
26
2540305S
12236
27
28
29
30%
31%
32%
24126130S
2404106S
2416454S
2404153S
2415327S
M651040S
1
2
4
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP —V-BELT COVER/OUTER MUFFLER SHIELD ASSY.
V-BELT COVER/OUTER MUFFLER SHIELD ASSY.
PAGE 66 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 66
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP —V-BELT COVER/OUTER MUFFLER SHIELD ASSY.
V-BELT COVER/OUTER MUFFLER SHIELD ASSY.
NO.
1
2
3
4
PART NO.
21462
11819
21312
21309
PART NAME
QTY.
REMARKS
SHIELD, MUFFLER OUTER
SCREW, HHC FLANGED 1/4-20X3/4"
GUARD, BELT REAR
GUARD, BELT
1
7
1
1
7
5
11534
NUT, U-TYPE 1/4-20
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — SPIDER ASSY. (RIGHT)
SPIDER ASSY. (RIGHT)
PAGE 68 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 68
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — SPIDER ASSY. (RIGHT)
SPIDER ASSY. (RIGHT)
NO.
1%
2%
3%
4%
5
PART NO.
11419
11431-1
2621
12779
12101
12097
1456
11039
11594
11904
9006
2829
1207
0161 C
1162 A
1322
PART NAME
QTY. REMARKS
PLATE, WEARTHRUST COLLAR
1
THRUST COLLARW/ BUSHING...................................1..... INCLUDES ITEMS W/+
ZERK, GREASE STR 1/4 - 24
BEARING, THRUST 6017 2RS W/ FLANGE
KEY, 5/16 SQ. X 2-5/8 HRDND
SCREW, SQHS 3/8 - 16 X 1-3/4 CONE 8
NUT, HEX FINISH 3/8 - 16
BUSHING,TROWEL ARM 2-PIECE
SPRING, TROWEL ARM LEVER RIGHT
LEVER, TROWEL ARM HAND RIDE SIDE
PIN, ROLL 5/16 X 2 NO PLATE
ARM, TROWEL HD EXT.
SCREW, HHC 5/16 -18 X 1-3/4
WASHER, LOCK, 5/16 MED
CAP, GREASE ZERK #2
SCREW ASSEMBLY, ARM RETAINING
WASHER, INT. SHKP. 3/8
SCREW, TROWEL ADJUSTMENT
NUT, HEX JAM 3/8 - 16 CLASS 2B
WASHER, LOCK, 3/8 MEDIUM
SCREW, HHC 3/8 -16 X 1/4
1
1
1
2
2
8
4
4
4
6
7
*
*
9
*
10
*
11
*
12
*
13
*
4
15
12
12
5
4
4
4
4
4
4
*
16
*
17
*
18
*
19
1875
0164 B
1876
*
20
*
21
*
22
*
0166 A
23 # 11602
*
24
25
26
12072-1
12785
SPIDER/ARM ASSY. R.S. 4BLD 1-1/4 MAIN SHAFT...1..... INCLUDES ITEMS W/
*
SPIDER, SERVICE 4BLD 1-1/4 SHAFT .......................1..... INCLUDES ITEMS W/#
BLADE ASSEMBLY ..................................................... 4 ..... CONTACT UNIT SALES DEPT./
.............................................................................................. ACCESSORY ITEM
*
27+% 12316
28% 20938
THRUST COLLAR BUSHING
THRUST COLLAR KIT ..................................................1 ..... INCLUDES ITEMS W/%
1
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — SPIDER ASSY. (LEFT)
SPIDER ASSY, (LEFT)
PAGE 70 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 70
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — SPIDER ASSY. (LEFT)
SPIDER ASSY. (LEFT)
NO.
1%
2%
3%
4%
5
PART NO.
11419
11431-1
2621
12779
12101
12097
1456
11039
11595
11903
9006
21495
1207
0161 C
1162 A
1322
1875
0164 B
1876
PART NAME
QTY.
REMARKS
PLATE, WEAR THRUST COLLAR
1
THRUST COLLARW/ BUSHING................................ 1............. INCLUDES ITEMS W/+
ZERK, GREASE 1/4 - 28
1
1
1
2
2
8
4
4
4
4
12
12
5
4
4
4
4
4
4
BEARING, THRUST 6017 2RS W/ FLANGE
KEY, 5/16 SQ. X 2 - 5/8 HRDND
SCREW, SQHS 3/8 - 16 X 1-3/4 CONE 8
NUT, HEX FINISH 3/8 - 16
BUSHING,TROWEL ARM 2-PIECE
SPRING, LEFT TROWEL ARM LEVER
LEVER, TROWEL ARM LEFT SIDE
PIN, ROLL 5/16 X 2 NO PLATE
ARM, TROWEL L.S.
SCREW, HHC 5/16 -18 X 1-3/4
WASHER, LOCK, 5/16 MED
CAP, GREASE ZERK #2
SCREW ASSY, ARM RETAINING
WASHER, INT. SHKP. 3/8
SCREW, TROWEL ADJUSTMENT
NUT, HEX JAM 3/8 - 16 CLASS 2B
WASHER, LOCK, 3/8 MEDIUM
SCREW, HHC 3/8 -16 X 1/4
6
7
*
*
9
*
10
*
11
*
12
*
13
*
15
*
16
*
17
*
18
*
19
*
20
*
21
*
22
*
0166 A
23 # 11602
*
24
25
26
21310-1
12785
SPIDER ASSY., L.S. 4BLD 1-1/4 MAIN SHAFT ........ 1............. INCLUDES ITEMS W/
*
SPIDER, SERVICE 4BLD 1-1/4 SHAFT .................... 1............. INCLUDES ITEMS W/#
BLADE ASSEMBLY ................................................... 4............. CONTACT UNIT SALES DEPT./
................................................................................................... ACCESSORY ITEM
*
27+% 12316
28% 20938
THRUST COLLAR BUSHING
THRUST COLLAR KIT ............................................... 1............. INCLUDES ITEMS W/%
1
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP —YOKE ASSY.
YOKE ASSY.
PAGE 72 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 72
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP —YOKE ASSY.
YOKE ASSY.
NO.
1
2
3
4
5
6
PART NO.
12100-1
0683
10136
9028
1116
PART NAME
QTY.
REMARKS
YOKE
2
4
6
2
4
2
PIN, COTTER 3/32 X 3/4
WASHER, FLAT 3/8 SAE
PIN, YOKE
NUT, BRASS JAM 5/16 -18
CABLE ASSEMBLY 26.38 HT-V PITCH
12460
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP —THROTTLE CABLE/FOOT PEDALS ASSY.
THROTTLE CABLE/FOOT PEDALS ASSY.
PAGE 74 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 74
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP —THROTTLE CABLE/FOOT PEDALS ASSY.
THROTTLE CABLE/FOOT PEDALS ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
2124
2754
2753
2755
0937
10019
2203
PART NAME
QTY.
1
1
1
1
2
1
2
1
1
2
1
1
2
1
1
4
4
4
1
4
2
1
2
2
1
1
1
1
REMARKS
CABLE, CONTROL (RT)
ADAPTER, THROTTLE SPRING, LONG
SPRING, THROTTLE RETURN
ADAPTER, THROTTLE SPRING, SHORT
NUT, HEX 10 - 32 ZINC PLTD
NUT, NYLOC 10 - 32
WASHER, FLAT #10 SAE
ROD END, 10 - 32 FEMALE RH
SCREW, SHC 10 - 32 X 1
PIN, COTTER 3/32 X 1
2153
9
10018
6014 B
12635
12637
10136
3083
2772
3233
0300 B
5283
2086
0202
10019
2884
5065 B
2192
2194
2153
2190
10018
0937
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
RISER, LEFT FOOT
RISER, RIGHT FOOT
WASHER, FLAT 3/8 SAE
SPACER, 3/4 X 3/8 X 7/8 LONG
PIN, ACCELERATOR PEDAL
WASHER, FENDER 1.50D X 3/8 ID
WASHER, FLAT 5/16 SAE
NUT, NYLOC 5/16 -18
PEDAL ACCELERATOR
SCREW, HHC 5/16 - 18 X 1 ZINC
NUT, NYLOC 10-32
BRACKET, THROTTLE CABLE
SCREW, RHM 10-32 X 1/2
SPRING, EXTENSION RT
NUT, THROTTLE
ROD END, 10 - 32 FEMALE RH
SPACER, THROTTLE
SCREW, SHC 10-32 1 NP (1)
NUT, FULL HEX 10 - 32 ZINC PLTD
1
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — CONTROL PANEL ASSY.
CONTROL PANEL ASSY.
PAGE 76 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 76
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — CONTROL PANEL ASSY.
CONTROL PANEL ASSY.
NO.
1
2
3
4
4A
5
6
7
8
PART NO.
21458-1
4682
PART NAME
QTY.
1
1
1
1
1
1
1
4
4
4
2
4
2
1
3
1
REMARKS
CONTROL PANEL
SWITCH, LIGHT TOGGLE
BOOT, TOGGLE SWITCH
IGNITION SWITCH, W/KEY
KEY, IGNITION (SET)
CABLE, CHOKE
CIRCUIT BREAKER, 30A, 12V
NUT, NYLOC 10 - 32
SCREW, RHM 10 - 32 X 1/2
WASHER, FLAT #10 SAE
SCREW, HHC 3/8 - 16 X 1
WASHER, FLAT USS 3/8 PLD
NUT, NYLOC 3/8 - 16
HARNESS, WIRE ENGINE
TIE WRAP
8381
2509904S
4834001S1
11029
2673
10019
5065 B
2203
0205
4001
10133
2945
60101
21523
1475
9
10
11
12
13
14
15
16
17
18
WIRE, YELLOW 10 AWG
CONNECTOR, SPLICETAP
WIRE, LITE SWITCH
1
1
2
2769
8133
SCREW, PHP 10-32 X 3/4
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — FUEL ASSY.
FUEL ASSY.
PAGE 78 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 78
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — FUEL ASSY.
FUEL ASSY.
NO.
1
2
3
4
5
6
7
PART NO.
PART NAME
QTY.
REMARKS
12404
TANK, FUEL FIVE GALLON
FUEL CAP/GAUGE (10.5)
SCREW, HHC 1/4 - 20 X 5/8
WASHER, FLAT, 1/4 SAE
BUSHING, RUBBER FUEL
VALVE, SCREENED DAPCO 12570
CLAMP, WORM HOSE, #4 (1/4 - 5/8)
1
1
6
6
1
1
3
11418
4514
0948
19633
20795
19473
8
9
10
11
12
13
60079
HOSE, FUEL 5/16 ID..............................................3.................. SOLD IN 1 FT. LENGTHS
0181 B
2405002S
2555901S
2405010S
2429
WASHER, LOCK, 1/4 MED
FILTER, FUEL PRIMARY 1/4" INLET
FUEL PUMP, 12 VDC
4
1
1
1
1
FILTER, FUEL SECONDARY
HOLDER, SPARE BELT
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 79
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — BATTERY ASSY.
BATTERY ASSY.
PAGE 80 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 80
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — BATTERY ASSY.
BATTERY ASSY.
NO.
1
2
3
4
PART NO.
2509
10031
11105
2449
PART NAME
QTY. REMARKS
WING NUT, PLATED
2
2
1
1
2
WASHER, EXT SHKP 1/4
BRACKET BATTERY HOLD DOWN
BOX, BATTERY GR UI
SCREW, HHC 1/4 - 20 X 3/4
5
0131 A
6
7
8
9
10
11
12
13
14
15
16
BATTERY, ................................................ 1 ....... PURCHASE LOCALLY, INTERSTATE #SP40
0181 B
0949
12022
12675
1597
0655
20146
2866
WASHER,LOCK, 1/4 MEDIUM
NUT, HEX FINISH 1/4 - 20
2
2
1
1
1
4
2
1
1
4
CABLE, BATTERY NEG 4GA 20 - 1/2"
CABLE, BATTERY POS 4GA 36"
CABLE, BATTERY NEG 4GA 16 - 1/2"
SCREW, HHC 5/16 - 18 X 1- 3/4
BRACKET BATTERY BOX
SCREW, HHC M8 X 1.25 X 20MM
WASHER, EXT SHKP 5/16
13339
5283
NUT, NYLOC 5/16 - 18
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 81
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — SEAT FRAME ASSY.
SEAT FRAME ASSY.
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 82
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — SEAT FRAME ASSY.
SEAT FRAME ASSY.
NO.
1
2
3
4
PART NO.
21861
11472-1
0300 B
5283
PART NAME
SEAT, MICHIGAN-ADJUSTABLE W/O ARMS
SEAT PLATE
WASHER, FLAT, SAE 5/16
NUT, NYLOC 5/16 - 18
QTY.
1
1
4
4
REMARKS
5
6
7
8
10896-1
11644
10237
8156
FRAME, SEAT
1
1
1
1
1
1
1
2
2
4
1
4
1
1
1
1
SCREW, HHC, WASHER 10 - 32 X 5/8
WASHER, EXT. SHKP, #10
SCREW, HHC 3/8 - 16 X 2 - 1/2
WASHER, FLAT 3/8 PLTD STD. USS
SPRING, SEAT
9
4001
10
11
12
13
14
15
16
17
18
19
20
21
22
11593
10133
0183
NUT, NYLOC 3/8 - 16
PIN, COTTER 1/8 1 - 1/4
PIN, CLEVIS 1/2 X 2.75 EFF.
SCREW, HHC 1/2 - 13 X 5
WIRE, RELAY GROUND
NUT, NYLOC1/2 - 13
NUT, NYLOC 10 - 32
CONNECTOR, RELAY
RELAY, KILL
SWITCH, KILL COLE- HER #90036- 02
TERMINAL, WIRE
8081
10307
12014
10176
10019
12018
12017
12005
12020
10306
4
2
SCREW, HHC 1/2-13 X 4 1/2
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 83
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE — PARTS
Effective: July 15, 2003
Terms and Conditions of Sale
STOW Construction Equipment
PAYMENT TERMS
DROP SHIPMENTS
Terms of payment for unit sales are 2% 15 days
net 30 days from date of invoice unless
otherwise specifically stated on our invoice. Parts
invoices have terms of net 10 days. Minimum
parts billing is $15.00 net.
Applicable discounts will be computed on
merchandise value only. Late charges will be
assessed at prevailing rates. Cash discounts
cannot be taken on current billings if any
previously billed amounts are past due.
STOW reserves the right to refuse Drop
Shipments outside the normal service area of
the purchasing dealer.
The sender will be notified of any material
received that does not meet the above provisions.
Such material will be held for 30 days from
notification pending instructions. If a reply is not
received within 30 days, the material will be
returned to the sender at his expense with no
credit issued.
FIELDWAREHOUSES
Field Warehouses are currently located in
California, Georgia, Idaho, Iowa, and New
Jersey
PRICING, REBATES AND
SPECIFICATIONS
Every effort will be made to provide adequate
notice of changes; however, prices and
equipment specifications are subject to change
without notice.
SPECIAL EXPEDITING SERVICE
The higher of a $35.00 surcharge or actual costs
will be added to the invoice for special handling,
including bus shipments, or in cases where
STOW personnel must personally deliver the
equipment or parts to the carrier.
FREIGHT POLICY
Freight policy is established to offer customers
every advantage possible. Due to bulk freight
ratings on some equipment and other shipping
considerations, freight policies differ by
equipment type. Actual back freight may be
charged for shipments originating from other
than specified FOB warehouses. See Freight
Policy for details.
All STOW domestic sales are FOB nearest
available designated MQ/STOW warehouse.
Export orders are ex-works factory located in
Carson, CA or Boise, ID.
Price changes are effective on a specific date
and all orders received on or after that date will
be billed at the revised price.
RETURNED GOODS POLICY
Return shipments may be accepted and credit
allowed, subject to the following provisions.
Rebates for price reductions and added charges
for price increases will not be made for stock in
dealer inventory at the time of a price change.
1. A Returned Material Authorization (RMA)
must be approved by STOW prior to
shipment. Approvals for returned goods must
be with just cause and are at the
sole discretion of STOW. A copy of the
Authorization must accompany the shipment
to the designated Warehouse.
STOW reserves the right to quote and sell direct
to Government agencies and to Original
Equipment Manufacturer accounts who use our
products as integral parts of their own products.
Additions to orders already shipped cannot be
accepted for freight minimums.
LIMITATION OF SELLER’S LIABILITY
2. Parts being returned must be listed as
currently supplied on the current parts list.
STOW shall not be liable hereunder for damages
in excess of the purchase price of the item with
respect to which damages are claimed and in
no event shall STOW be liable for loss of profit
or good will or for any other special, consequential
or incidental damages.
Should STOW elect to make partial shipments
of an order originally complying with the “freight
allowed” requirements, transportation charges
will be absorbed by STOW on any subsequent
shipment applying to that order.
3. Parts must be in new and resalable condition
in the original package, with part numbers
clearly marked.
4. Units and accessories must be current
models in the latest price list and in new and
resalable condition.
All other orders will be shipped collect or prepaid
with charges added to the invoice. STOW’s
responsibility ceases when a signed manifest
has been obtained from the carrier, and any
claim for shortage or damage must be settled
between the consignee and the carrier.
LIMITATION OF WARRANTIES
There are no warranties, express or implied,
made by STOW. hereunder on Products
manufactured or distributed by it except the
warranty against defects in material and
workmanship on new Products to the original
purchaser, as set forth in the STOW New Product
Limited Warranty.
5. Special order items are not returnable for
credit.
6. Credit on returned parts and units will be
issued at actual dealer net price at time of
purchase less 15% restocking charge.
Parts: FOB Carson, California or Boise, Idaho.
See Freight Policy for details and
additional discounts.
7. All returned shipments are to be made to the
STOW designated receiving point, freight
prepaid at the sender’s expense.
STOW CONSTRUCTION EQUIPMENT
POST OFFICE BOX 6254
CARSON, CALIFORNIA 90749
310-661-4242 • 877-BUY-STOW
FAX:310-604-9237
E-MAIL: [email protected]
Atlanta • Boise • Newark • Quebec, Canada
Manchester, UK • Rio de Janeiro, BR • Puebla, MX
PAGE 84 — STR 31V
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 84
Download from Www.Somanuals.com. All Manuals Search And Download.
STR46SP — NOTES
STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 85
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
STOW MAIN OFFICE
Post Office Box 6254
Carson, Ca 90749
888-252-STOW
FAX:310-537-1986
Email: [email protected]
PARTS DEPARTMENT
800-427-1244
310-537-3700
FAX:800-672-7877
FAX:310-637-3284
SERVICE DEPARTMENT
800-478-1244
FAX:310-537-4259
310-537-3700
TECHNICAL ASSISTANCE
800-478-1244
FAX:310-631-5032
FAX:310-537-1173
WARRANTYDEPARTMENT
800-421-1244, EXT.279
310-537-3700, EXT.279
SALES DEPARTMENT
310-661-4242
FAX:310-604-9237
877-289-7869(877-BUY-STOW)
Your Local Dealer is:
STOW CONSTRUCTION EQUIPMENT
A DIVISION OF MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
888-252-STOW [888-252-7869]
FAX:310-537-1986
Download from Www.Somanuals.com. All Manuals Search And Download.
|