Scag Power Equipment Lawn Mower SW32 15KAI User Manual
OPERATOR’S  
MANUAL  
SW  
Model:  
Walk-Behind  
SW32-15KAI  
SW36A-15KH  
SW36A-16KAI  
SW36A-17KAI  
SW48V-15KH  
SW48V-16KAI  
SW52V-17KAI  
C ongra tula tions on owning a Sc a g mower! This ma nua l c onta ins the opera ting  
instruc tions a nd sa fety informa tion for your Sc a g mower. Rea ding this ma nua l  
c a n provide you with a ssista nc e in ma intena nc e a nd a djustment proc edures to  
keep your mower performing to maximum efficiency. The specific models that  
this book c overs a re listed on the inside c over. Before opera ting your ma c hine,  
plea se rea d a ll the informa tion enc losed.  
© 2009  
PART NO. 03224 Rev. 2  
PRINTED 1/2009  
Sc a g Power Equipment  
Division of Meta lc ra ft of Ma yville, Inc .  
PRINTED IN USA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
Table of Contents  
Table of Contents  
SECTION 1 - GENERAL INFORMATION...................................................................................1  
1.1 INTRODUCTION...........................................................................................................................................1  
1.2 DIRECTION REFERENCE...........................................................................................................................1  
1.3 SERvICING THE ENGINE AND DRIvE TRAIN COMPONENTS.................................................................1  
1.4 SYMBOLS ....................................................................................................................................................2  
SECTION 2 - SAFETY INFORMATION......................................................................................3  
2.1 INTRODUCTION...........................................................................................................................................3  
2.2 SIGNAL WORDS..........................................................................................................................................3  
2.3 BEFORE OPERATION CONSIDERATIONS................................................................................................3  
2.4 OPERATION CONSIDERATIONS................................................................................................................4  
2.5 MAINTENANCE CONSIDERATIONS & STORAGE ....................................................................................5  
2.6 USING A SPARK ARRESTOR.....................................................................................................................6  
2.7 SAFETY AND INSTRUCTIONAL DECALS.................................................................................................7  
SECTION 3 - SPECIFICATIONS ................................................................................................8  
3.1 ENGINE ........................................................................................................................................................8  
3.2 ELECTRICAL ...............................................................................................................................................8  
3.3 ENGINE DECK.............................................................................................................................................8  
3.4 CUTTER DECK ............................................................................................................................................8  
3.5 WEIGHTS AND DIMENSIONS.....................................................................................................................9  
3.6 PRODUCTIvITY ...........................................................................................................................................9  
SECTION 4 - OPERATING INSTRUCTIONS ...........................................................................10  
4.1 CONTROLS AND INSTRUMENT IDENTIFICATION ................................................................................10  
4.2 SAFETY INTERLOCK SYSTEM................................................................................................................11  
4.3 INITIAL RUN-IN PROCEDURES................................................................................................................11  
4.4 STARTING THE ENGINE ...........................................................................................................................11  
4.5 GROUND TRAvEL AND STEERING .........................................................................................................11  
4.6 ENGAGING THE DECK DRIvE (CUTTER BLADES)................................................................................12  
4.7 HILLSIDE OPERATION..............................................................................................................................13  
4.8 PARKING THE MOWER.............................................................................................................................13  
4.9 AFTER OPERATION..................................................................................................................................13  
4.10 REMOvING CLOGGED MATERIAL ........................................................................................................14  
4.11 MOvING MOWER WITH ENGINE STOPPED..........................................................................................14  
4.12 RECOMMENDATIONS FOR MOWING....................................................................................................14  
SECTION 5 - TROUBLESHOOTING CUTTING CONDITIONS ...............................................15  
I
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
Table of Contents  
SECTION 6 - ADJUSTMENTS .................................................................................................18  
6.1 DRIvE CONTROL ADJUSTMENTS ..........................................................................................................18  
6.2 THROTTLE CONTROL AND CHOKE ADJUSTMENTS............................................................................18  
6.3 CUTTER DECK BELT ADJUSTMENTS ....................................................................................................18  
6.4 BELT ALIGNMENT.....................................................................................................................................19  
6.5 ADJUSTING CUTTING HEIGHT................................................................................................................19  
6.6 ELECTRIC CLUTCH ADJUSTMENT.........................................................................................................22  
SECTION 7 - MAINTENANCE..................................................................................................23  
7.1 MAINTENANCE CHART - RECOMMENDED SERvICE INTERvALS ......................................................23  
7.2 LUBRICATION............................................................................................................................................24  
7.3 ENGINE OIL ...............................................................................................................................................26  
7.4 ENGINE FUEL SYSTEM............................................................................................................................26  
7.5 ENGINE AIR CLEANER.............................................................................................................................27  
7.6 CUTTER BLADES......................................................................................................................................27  
7.7 TIRES..........................................................................................................................................................28  
SECTION 8 - ILLUSTRATED PARTS LIST ..............................................................................29  
8.1 SCAG APPROvED ATTACHMENTS AND ACCESSORIES......................................................................29  
32" & 36A CUTTER DECKS............................................................................................................................30  
48v & 52v CUTTER DECKS ...........................................................................................................................32  
NOTES..............................................................................................................................................................34  
CASTER ASSEMBLY.......................................................................................................................................35  
ENGINE DECK.................................................................................................................................................36  
HANDLE ASSEMBLY.......................................................................................................................................38  
INSTRUMENT PANEL......................................................................................................................................40  
PEERLESS TRANSMISSION 700-070 ...........................................................................................................41  
WIRE HARNESSES .........................................................................................................................................42  
REPLACEMENT DECALS AND INFORMATION PLATES .............................................................................44  
LIMITED WARRANTY - COMMERCIAL EqUIPMENT.........................Following Section 8  
II  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
Section 1  
GENERAL INFORMATION  
USE ONLY SCAG APPROvED ATTACHMENTS AND  
ACCESSORIES.  
1.1 INTRODUCTION  
Your mower was built to the highest standards in the  
industry. However, the prolonged life and maximum  
efficiency of your mower depends on you following the  
operating, maintenance and adjustment instructions in  
this manual.  
Attachments and accessories manufactured by companies  
other than Scag Power Equipment are not approved for  
use on this machine. See Section 8-1.  
WARNING  
If additional information or service is needed, contact your  
Scag Power Equipment Dealer.  
For pictorial clarity, some illustrations and figures  
in this manual may show shields, guards or plates  
open or removed.Under no circumstances should  
your mower be operated without these devices  
in place.  
We encourage you to contact your dealer for repairs.  
All Scag dealers are informed of the latest methods to  
service this equipment and provide prompt and efficient  
service in the field or at their service shop. They carry a  
full line of Scag service parts.  
All information is based upon product information available  
at the time of approval for printing. Scag Power Equipment  
reserves the right to make changes at any time without  
notice and without incurring any obligation.  
- IMPORTANT -  
The replacement of any part on this product  
by other than the manufacturer's authorized  
replacement part may adversely affect the  
performance, durability or safety of this  
product.  
1.2 DIRECTION REFERENCE  
Use of other than original Scag replacement  
parts will void the warranty.  
The “Right” and “Left”, “Front” and “Rear” of the machine  
are referenced from the operator’s right and left when  
seated in the normal operating position and facing the  
forward travel direction.  
When ordering parts, always give the model and serial  
number of your mower. The serial number plate is located  
on the frame of the machine between the engine and  
transmission were shown in Figure 1-1.  
1.3 SERvICING THE ENGINE AND DRIvE  
TRAIN COMPONENTS  
The detail servicing and repair of the engine and  
transmission are not covered in this manual; only routine  
maintenance and general service instructions are  
provided. For service of these components during the  
limited warranty period, it is important to contact your  
Scag dealer or find a local authorized servicing agent  
of the component manufacturer. Any unauthorized work  
done on these components during the warranty period  
may void your warranty.  
R
MODEL  
SERIA  
Mayville, Wisconsin 53050  
ivision yvillen,dIin  
PfatenttaslcIsra an ng.  
D
L
o
M
e
s
f
u
t
e
o
d
f
M
a
d
P
e
c
SERIAL NUMBER  
PLATE LOCATION  
Figure 1-1. Mower Serial Number Plate Location  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 1  
1.4 SYMBOLS  
SYMBOL  
DESCRIPTION  
SYMBOL  
DESCRIPTION  
Choke  
Transmission  
Parking Brake  
Spinning Blade  
Spring Tension on Idler  
Oil  
48071S  
On/Start  
Off/Stop  
Falling Hazard  
Fast  
Thrown Object Hazard  
Slow  
Continuously Variable - Linear  
Pinch Point  
Cutting Element - Basic Symbol  
Cutting Element - Engage  
Cutting Element - Disengage  
CE Mark  
481039S  
Hour meter/Elapsed Operating Hours  
STT MODELS  
Seat must be installed under the seat  
hold down bracket during installation.  
Failure to secure the seat under the hold  
down bracket could result in serious  
injury or death in a roll over.  
Thrown Object Hazard  
Keep Bystanders Away  
Read Operator's Manual  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 2  
SAFETY INFORMATION  
2.1 INTRODUCTION  
DANGER  
Your mower is only as safe as the operator. Carelessness  
or operator error may result in serious bodily injury  
or death. Hazard control and accident prevention are  
dependent upon the awareness, concern, prudence, and  
proper training of the personnel involved in the operation,  
transport, maintenance and storage of the equipment.Make  
sure every operator is properly trained and thoroughly  
familiar with all of the controls before operating the  
mower.The owner/user can prevent and is responsible for  
accidents or injuries occurring to themselves, other people  
or property.  
The signal word “DANGER” denotes that an extremely  
hazardous situation exists on or near the machine that  
could result in high probability of death or irreparable injury  
if proper precautions are not taken.  
WARNING  
The signal word “WARNING” denotes that a hazard exists  
on or near the machine that can result in injury or death if  
proper precautions are not taken.  
READ THIS OPERATOR’S MANUAL BEFORE  
ATTEMPTING TO STARTYOUR MOWER.  
A replacement manual is available from your authorized  
Scag Service Dealer or by contacting Scag Power  
Equipment, Service Department at P.O.Box 152, Mayville,  
WI 53050 or contact us via the Internet at www.scag.com.  
The manual for this machine can be downloaded by using  
the model and serial number or use the contact form to  
make your request. Please indicate the complete model  
and serial number of your Scag product when requesting  
replacement manuals.  
CAUTION  
The signal word“CAUTION”is a reminder of safety practices  
on or near the machine that could result in personal injury  
if proper precautions are not taken.  
Your safety and the safety of others depends significantly  
upon your knowledge and understanding of all correct  
operating practices and procedures of this machine.  
2.2 SIGNAL WORDS  
2.3 BEFORE OPERATION  
CONSIDERATIONS  
1. NEVER allow children to operate this mower. Do not  
allow adults to operate this machine without proper  
instructions.  
This symbol means “Attention! Become Alert! Your  
Safety is Involved!" The symbol is used with the following  
signal words to attract your attention to safety messages  
found on the decals on the machine and throughout this  
manual. The message that follows the symbol contains  
important information about safety. To avoid injury and  
possible death, carefully read the message! Be sure to fully  
understand the causes of possible injury or death.  
2. Do not mow when children and/or others are  
present. Keep children out of the mowing area and  
in the watchful care of a responsible adult other than  
the operator. Be alert and turn machine off if a child  
enters the area.  
3. DO NOT allow children to ride or play on the  
machine, it is not a toy.  
SIGNAL WORD:  
4. Clear the area to be mowed of objects that could be  
picked up and thrown by the cutter blades.  
It is a distinctive word found on the safety decals on the  
machine and throughout this manual that alerts the viewer  
to the existence and relative degree of the hazard.  
5. DO NOT carry passengers.  
6. DO NOT operate the machine under the influence of  
alcohol or drugs.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 2  
7. If the operator(s) or mechanic(s) cannot read English  
or Spanish, it is the owner's responsibility to explain  
this material to them.  
13. Keep flammable objects (cigarettes, matches, etc.),  
open flames and sparks away from the fuel tank and  
fuel container. Use only approved containers.  
8. DO NOT wear loose fitting clothing. Loose clothing,  
jewelry or long hair could get tangled in moving  
parts. Do not operate the machine wearing shorts;  
always wear adequate protective clothing including  
long pants. Wearing safety glasses, safety shoes and  
a helmet is advisable and is required by some local  
ordinances and insurance regulations.  
14. Equipment must comply with the latest requirements  
per SAE J137 and/or ANSI/ASAE S279 when driven  
on public roads.  
15. Do not operate without the side discharge chute  
installed and in the down position or with an optional  
grass catcher or mulch plate completely installed.  
16. Check the blade mounting bolts at frequent intervals  
for proper tightness.  
WARNING  
2.4 OPERATION CONSIDERATIONS  
Always wear hearing protection. Operating this  
machine over prolonged periods of time can  
cause loss of hearing.  
1. Know the function of all controls and how to stop  
quickly.  
9. Keep the machine and attachments in good  
operating condition. Keep all shields and safety  
devices in place. If a shield, safety device or decal  
is defective or damaged, repair or replace it before  
operating the machine.  
WARNING  
DO NOT operate on steep slopes. ALWAYS  
FOLLOW OSHA APPROvED OPERATION.  
2. Reduce speed and exercise extreme caution on  
slopes and in sharp turns to prevent tipping or loss  
of control. Be especially cautious when changing  
directions on slopes.  
WARNING  
This machine is equipped with an interlock system  
intended to protect the operator and others from  
injury. This is accomplished by preventing the  
engine from starting unless the deck drive is  
disengaged and the transmission is in neutral.  
The system shuts off the engine if the operator  
releases the operator pressence levers with the  
deck drive engaged and/or the transmission  
is not in neutral. Never operate equipment  
with the interlock system disconnected or  
malfunctioning.  
3. To prevent tipping or loss of control, start and stop  
smoothly, avoid unnecessary turns and travel at  
reduced speed.  
4. When using any attachment, never direct the  
discharge of material toward bystanders or allow  
anyone near the machine while in operation.  
5. Start the engine when the neutral latches are in  
the neutral lock position, the cutter blades are  
disengaged, and the transmission is in neutral.  
6. If the mower discharge ever plugs, shut off the  
engine, remove the ignition key, and wait for all  
movement to stop before removing the obstruction.  
10. Be sure the interlock switches are functioning  
correctly.  
11. Fuel is flammable; handle it with care. Fill the fuel  
tank outdoors. Never fill it indoors. Use a funnel or  
spout to prevent spillage. Clean up any spillage  
before starting the engine.  
12. DO NOT add fuel to a running or hot engine. Allow  
the engine to cool for several minutes before adding  
fuel. Never fuel indoors or inside enclosed trailers.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 2  
WARNING  
DANGER  
DO NOT use your hand to dislodge the clogged  
discharge chute. Use a stick or other device to  
remove clogged material after the engine has  
stopped running and the blades have stopped  
turning.  
DO NOT run the engine inside a building or  
a confined area without proper ventilation.  
Exhaust fumes are hazardous and contain  
carbon monoxide which can cause brain injury  
and death.  
7. Be alert for holes, rocks, roots and other hidden  
hazards in the terrain. Keep away from any drop-  
offs. Beware of overhead obstructions (low limbs,  
etc.), underground obstacles (sprinklers, pipes, tree  
roots, etc.). Cautiously enter a new area. Be alert for  
hidden hazards.  
16. Keep hands and feet away from cutter blades and  
moving parts. Contact can injure.  
17. Transport the mower using a heavy duty trailer  
or truck. Insure the trailer or truck has all of the  
necessary lighting and markings as required by  
laws, codes, and ordinances. Secure a trailer with a  
safety chain.  
8. Disengage power to cutter deck before backing up.  
Do not mow in reverse unless absolutely necessary  
and then only after observation of the entire area  
behind the mower. If you must mow in reverse,  
maintain a constant lookout to the rear of the  
machine and mow slowly.  
18. Be cautious when loading and unloading onto  
trailers or trucks. Use only a full width ramp.  
19. When transporting the mower, make sure the  
transmission is in neutral, the neutral latches are in  
the neutral lock position, the engine is off with the  
key removed, and the wheels have been blocked.  
9. DO NOT turn sharply. Use care when backing up.  
10. Disengage power to cutter deck before crossing  
roads, walks or gravel drives.  
20. Tie the mower down securely using straps, chains,  
cable, or ropes. Both front and rear straps must be  
directed down and outward from machine.  
11. Mow only in daylight or good artificial light.  
12. NEVER raise the deck with the blades engaged.  
21. Use care when approaching blind corners, shrubs,  
trees, or other objects that may obscure vision.  
13. Take all possible precautions when leaving the  
machine unattended, such as disengaging the  
mower, stopping the engine, and removing the key.  
22. NEVER leave the machine running unattended.  
2.5 MAINTENANCE CONSIDERATIONS &  
STORAGE  
14. Disengage power to the attachments when  
transporting or when not in use.  
15. The machine and attachments should be stopped  
and inspected for damage after striking a foreign  
object, and damage should be repaired before  
restarting and operating the machine.  
1. Never make adjustments to the machine with the  
engine running unless specifically instructed to do  
so. If the engine is running, keep hands, feet, and  
clothing away from moving parts.  
2. Place the transmission in neutral, neutral latches in  
the neutral lock position, stop engine and remove  
key or disconnect spark plug wire to prevent  
accidental starting of the engine when servicing or  
adjusting the machine. Wait for all movement to stop  
before adjusting, cleaning or repairing.  
CAUTION  
Do not touch the engine or the muffler while the  
engine is running or immediately after stopping.  
These areas may be hot enough to cause a  
burn.  
3. Remove spark plug wire before making any repairs.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 2  
4. Keep all nuts, bolts and screws tight, to ensure the  
machine is in safe working condition. Check blade  
mounting bolts frequently to be sure they are tight.  
5. Do not change the engine governor settings or  
overspeed the engine. See the engine operator's  
manual for information on engine settings.  
6. To reduce fire hazard, keep the cutting units, drives,  
muffler and engine free of grass, leaves, excessive  
grease, oil and dirt.  
7. Park the machine on level ground.  
8. NEVER allow untrained personnel to service the  
machine.  
9. Use care when checking blades. Use a Blade Buddy,  
wrap the blade(s) or wear gloves and USE CAUTION  
when servicing blades. Only replace blades. NEVER  
straighten or weld blades.  
10. Keep all parts in good working condition. Replace all  
worn or damaged decals.  
11. Use jack stands to support components when  
required.  
12. Carefully release pressure from components with  
stored energy.  
13. Let the engine cool before storing.  
14. DO NOT store the machine near an open flame.  
15. Shut off fuel while storing or transporting.  
16. DO NOT store fuel near flames or drain indoors.  
2.6 USING A SPARK ARRESTOR  
The engine in this machine is not equipped with a spark  
arrestor muffler. It is in violation of California Public  
Resource Code Section 4442 to use or operate this engine  
on or near any forest covered, brush covered or grass  
covered land unless the exhaust system is equipped with  
a spark arrestor meeting any applicable local or state laws.  
Other states or federal areas may have similar laws.Check  
with your state or local authorities for regulations pertaining  
to these requirements.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 2  
2.7 SAFETY AND INSTRUCTIONAL DECALS  
WARNING  
WARNING  
INSTALL BELT COvER BEFORE  
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING  
OPERATING MACHINE  
KIT, OR ENTIRE GRASS CATCHER INSTALLED  
READ OPERATOR'S MANUAL  
483405  
483402  
483405  
WARNING  
ROTATING BLADES AND BELTS  
SPINNING BLADES  
KEEP CLEAR  
* Keep hands, feet & clothing clear  
* Keep all guards in place  
* Shut off engine & disengage blade  
clutch before servicing  
BLADE CONTACT & THROWN  
OBJECTS CAN INJURE  
483505  
* Use caution in directing discharge  
* Read instruction manual before operating  
483505  
DO NOT OPERATE UNLESS GRASS  
CATCHER, MULCHING KIT OR  
DISCHARGE CHUTE IS INSTALLED  
WARNING  
Operation of this equipment  
may create sparks that can  
start ꢀres around dry  
483406  
483406  
vegetation. A spark  
arrestor may be required.  
The operator should contact  
local ꢀre agencies for laws  
or regulations relating to  
ꢀre prevention requirements.  
483900  
483900  
(supplied with California models only)  
WARNING  
MOUNT RIDING  
ATTACHMENT  
HERE  
CAUTION  
!
FALLING HAzARD  
USE ONLY SCAG APPROvED  
RIDING ATTACHMENTS  
Avoid injury from burns.  
Shut off engine before  
removing fuel tank cap.  
483404  
SEE OPERATOR'S MANUAL  
Molded in Fuel Tank  
483404  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 3  
SPECIFICATIONS  
3.1 ENGINE  
General Type ................................................................................................Heavy Duty Industrial/Commercial Gasoline  
Brand......................................................................................................................................................Kohler, Kawasaki  
Horsepower:  
(Scag Model SW32-15KAI) .....................................................................................15 HP (Spec. # FH430V-BS33-R)  
(Scag Model SW36A-15KH, SW48V-15KH) ......................................................................15 HP (Spec. # PS-41621)  
(Scag Model SW36A-16KAI, SW48V-16KAI)..........................................................16 HP (Spec. # FH480V-BS24-R)  
(Scag Model SW36A-17KAI, SW52V-17KAI)..........................................................17 HP (Spec.# FH541V-BS38-R))  
Cylinders...................................................................................................................2 with Cast-Iron Sleeves - Kawasaki  
.........................................................................................................................................1 with Cast-Iron Sleeve - Kohler  
Governor................................................Mechanical Type with Variable Speed Control Set At 3600 RPM (+/- 100 RPM)  
Idle Speed:  
Kohler.................................................................................................................................... 1200 RPM (+/- 75 RPM)  
Kawasaki............................................................................................................................. 1550 RPM (+/- 150 RPM)  
Fuel...................................................................................... Non-Leaded Gasoline with a Minimum Octane Rating of 87  
Oil Pump...............................................................................................varies - see engine manufacturer's specifications  
Starter:  
Kohler / Kawasaki................................................................................................................................... Recoil Starter  
3.2 ELECTRICAL  
Starter......................................................................................................................... Electrical Ignition wi.Recoil Starter  
Interlock Switches................................................Operator Presence, Mower Engagement (BBC), Transmission Neutral  
Instrument Panel ................................................................................................Key Switch, Throttle Lever, PTO Switch,  
3.3 ENGINE DECK  
Drive System ...................................................................................... Dual Belt Drive w/5-Speed Peerless Transmission  
Steering/Travel Control....................................................................................................Clutch/Brake Fingertip Steering  
Wheels:  
(2) Front Caster....................................................................................................9 X 3.5 Flat-Free w/Roller Bearings  
(2) Drive - ............................................................................... 15 x 6.5-6 Two-Ply Pneumatic Tubeless, Radius Edge  
Tire Pressure:  
Front Caster....................................................................................................................................................Flat-Free  
Drive.................................................................................................................................................................. 12 PSI  
Fuel Tank ........................................................ 6-Gallon Seamless Polyethylene Tank with Large Opening and Fuel Cap  
Travel Speed:  
Forward ..........................................................................................................................................................2-6 MPH  
Reverse ..........................................................................................................................................................0-2 MPH  
-NOTE- The machine will travel at 6 mph for transport purposes. For best cutting performance the forward travel  
speed should be adjusted depending upon the cutting conditions.  
3.4 CUTTER DECK  
Type......................................................................................................................Out-Front design with anti-scalp rollers  
Construction ...............................7-Gauge Deck Top w/10-Gauge Reinforced Spindle Area, 7-gauge (3/16") Deck Skirt.  
True Cutting Width:  
32 ...........................................................................................................................................................33" (81.3 cm)  
36 .........................................................................................................................................................35.5" (90.2 cm)  
48 ..........................................................................................................................................................48" (122.0 cm)  
52 ..........................................................................................................................................................52" (132.0 cm)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 3  
Cutting Height Adjustment................................................................ Adjustment from, 1-3/4" to 4-1/4" in 1/4"increments  
Cutter Blades............................................................................. 0.197 in. Thick, Milled Edge, Wear Resistant Marbain™  
Blade Engagement............................................................Electric Blade Engagement Clutch with Control Panel Switch  
Connected to the Cutter Deck through a Belt.  
Discharge Opening...............................................Extra Wide Discharge Opening with Spring-Loaded Discharge Chute  
Discharge Chute...................................................................................................Black, Polypropylene (Plastic), Flexible  
Spindles.............................................................................Cast-Iron Housing, Tapered Roller Bearings with Top Access  
Grease Fitting and Grease Overfill Relief Poppet  
Spindle Pulleys........................................................................................................Split Steel with Tapered Locking Hub  
Cutter Deck Belts...................................................................B-section with Kevlar Cord. Self-Adjusting, Self-Tightening  
Electric Clutch Type................................................................................................Ogura Heavy Duty PTO Clutch Brake  
3.5 WEIGHTS AND DIMENSIONS  
32 / 36A  
48v  
52v  
Length..................................................................................... 70" / 72" ............................ 76" ....................................76"  
Tracking Width ........................................................................ 32" / 37" ............................ 37" ....................................37"  
Overall Width w/chute down ................................................... 43" / 47" ...........................60.5"................................64.5"  
Overall Width w/chute up........................................................ 33" / 37" ............................ 49" ....................................53"  
Overall Height.......................................................................40.5 / 40.5".........................40.5"................................40.5"  
Operating Weight..................................................................450# / 470# ........................515#................................535#  
3.6 PRODUCTIvITY  
32 / 36  
48  
52  
Cutting Width.......................................................................... 32" / 36" ............................ 48" ....................................52"  
Acres Per Day..........................................................................8.3 / 9.3 ........................... 12.4..................................13.5  
The preceding chart will aid you in determining how many acres your Scag mower will cut per day. The chart is an  
estimate based on 8 hours per day cutting time at 4 MPH with a 20% allowance for overlap and turns.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 4  
OPERATING INSTRUCTIONS  
2. Mower Deck Switch (Figure 4-1). Used to engage  
and disengage the mower drive system. Pulling up  
on the switch will engage the deck drive. Pushing  
down on the switch will disengage the deck drive.  
CAUTION  
Do not attempt to operate this mower unless you  
have read this manual. Learn the location and  
purpose of all controls and instruments before  
you operate this mower.  
3. Engine Choke Control (Figure 4-1). Used to start  
a cold engine.  
4. Engine Throttle Control (Figure 4-1). Used to  
control the engine speed. Pushing the lever forward  
increases engine speed. Pulling the lever back  
decreases engine speed. Full back position is the  
IDLE position. Full forward is the cutting position.  
4.1 CONTROLS AND INSTRUMENT  
IDENTIFICATION  
5. Left Steering / Brake Control (Figure 4-1). Used  
to control the mower's left wheel when traveling  
forward or reverse. Pull upward to apply brake.  
Before operating the mower, familiarize yourself with all  
mower and engine controls.Knowing the location, function  
and operation of these controls is important for safe and  
efficient operation of the mower.  
6. Right Steering / Brake Control (Figure 4-1). Used  
to control the mower's right wheel when traveling  
forward or reverse. Pull upward to apply brake.  
1. Ignition Switch (Figure 4-1). The ignition switch  
is used to start the engine. Turn the key to the on  
position before pulling the recoil starter.  
TRANSMISSION SHIFT  
LEVER  
ENGINE  
THROTTLE  
CONTROL  
NEUTRAL LATCH  
NEUTRAL LATCH  
RIGHT STEERING /  
BRAKE CONTROL  
LEFT STEERING /  
BRAKE CONTROL  
OPERATOR PRESSENCE  
CONTROL  
OPERATOR PRESSENCE  
CONTROL  
MOWER  
DECK  
SWITCH  
IGNITION  
SWITCH  
Figure 4-1. Controls and Instruments  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 4  
7. Transmission Shift Lever (Figure 4-1). Used to  
select the forward speed or selecting reverse. The  
machine must be at a complete stop before shifting  
between gears or shifting between forward and  
reverse.  
4.4 STARTING THE ENGINE  
CAUTION  
DO NOT USE STARTING FLUIDS. Use of starting  
fluids in the air intake system may be potentially  
explosive or cause a“runaway”engine condition  
that could result in engine damage and/or  
personal injury.  
8. Neutral Latch (Figure 4-1). Used to secure the belt  
drive system in neutral. Apply neutral latches when  
parking the machine.  
9. Operator Pressence Control (Figure 4-1)  
The operator pressence control levers must be  
depressed before the transmission is shifted out of  
neutral or engaging the mower deck.  
1. Be sure the fuel shutoff valve, located by the fuel  
tank, is completely open. (See Section 7.5.)  
4.2 SAFETY INTERLOCK SYSTEM  
2. Apply the neutral latch levers  
The mower is equipped with a safety interlock system that  
shuts off the engine if the operator releases the operator  
presence levers with the deck drive engaged and/or the  
transmission is not in neutral.Never operate equipment with  
the interlock system disconnected or malfunctioning..  
3. Shift the transmission into neutral.  
4. Place the PTO switch in the disengaged position.  
5. If the engine is cold, choke the engine as needed.  
6. Move the engine throttle control to about half engine  
speed.  
WARNING  
Never operate the mower with the interlock  
system disconnected or malfunctioning. Do not  
disengage or bypass any switch;injury to yourself  
and others or property damage could result.  
7. Turn the ignition key to the ON position.  
8. Pull the recoil starter on the engine.  
9. Allow engine to warm before operating the mower.  
4.5 GROUND TRAvEL AND STEERING  
- IMPORTANT -  
4.3 INITIAL RUN-IN PROCEDURES  
If you are not familiar with the operation of a walk  
behind mower with a transmission, the steering  
and ground speed operations should be learned  
and practiced in an open area, away from buildings,  
fences, or obstructions.  
FIRST DAY OF USE OR APPROxIMATELY 20 HOURS  
1. Check all belts for proper alignment and wear at 2, 4  
and 8 hours.  
Learn the operation on flat ground before operating  
on slopes.  
2. Change the engine oil and oil filter after the first 20  
hours of operation. (See Section 7.4.)  
Start practicing with a slow engine speed and slow  
forward travel.  
3. Check for loose hardware. Tighten as needed.  
4. Check interlock system for proper operation. (See  
Section 4.2.)  
Learn to feather the steering controls to obtain a  
smooth operating action.  
5. Check tire pressure. Adjust pressure if necessary.  
(See Section 7.10.)  
Practice operating the mower until you are  
comfortable with the controls before proceeding  
to mow.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 4  
FORWARD TRAvEL  
CAUTION  
Before backing up, observe the rear for persons  
and obstructions. Clear the area before backing  
up. Possible injury or property damage could  
occur.  
To travel forward with the mower, select the desired speed  
using the transmission shift lever, pull steering / brake  
control levers upward, release the neutral latch for both  
sides and slowly release both the left and right steering /  
brake control levers.The higher the gear selected using the  
transmission shift lever, the faster the machine will travel.  
To stop the forward travel, pull upward on the steering /  
brake control levers, lock the neutral latches and shift the  
transmission into neutral.  
To travel in reverse, select the reverse gear using the  
transmission shift lever, pull steering / brake control levers  
upward, release the neutral latch for both sides and slowly  
release both the left and right steering / brake control levers.  
Keep the travel speed low while traveling in reverse.  
To steer the mower left while traveling forward, pull upward  
on the left steering / brake control lever.The further the lever  
is pulled upward, the quicker the mower will turn left.  
- NOTE -  
To steer the mower right while traveling forward, pull upward  
on the right steering / brake control lever. The further the  
lever is pulled upward, the quicker the mower will turn  
right.  
The mower may not travel straight in reverse.  
To steer left while traveling in reverse, pull upward on the  
left steering / brake control lever. The further the lever is  
pulled upward, the quicker the mower will turn left.  
To steer right while traveling in reverse, pull upward on the  
right steering / brake control lever. The further the lever is  
pulled upward, the quicker the mower will turn right.  
WARNING  
To avoid serious bodily injury and damage to the  
transmission, the machine must be at a full stop  
before shifting between gears or shifting between  
forward and reverse.  
To stop the reverse travel, pull upward on the steering /  
brake control levers, lock the neutral latches and shift the  
transmission into neutral.  
4.6 ENGAGING THE DECK DRIvE (CUTTER  
BLADES)  
- NOTE -  
Smooth operation of the steering / brake control  
levers will produce smooth mower operation.While  
learning the operation of the steering controls,  
keep the travel speed low.  
1. Set the throttle at about 3/4 speed. Do not attempt to  
engage the deck drive at high speed as this shortens  
the electric clutch life — use only moderate engine  
speed when engaging the deck drive.  
REvERSE TRAvEL  
2. Engage the deck drive by pulling out on the yellow  
switch, located on the instrument panel, to the  
engage position. See Figure 4-2.  
CAUTION  
Disengage power to the mower before backing  
up. Do not mow in reverse unless absolutely  
necessary and then only after observation of the  
entire area behind the mower.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 4  
4. Travel across the slope whenever possible. Never up  
and down the slope.  
5. Keep tires properly inflated.  
4.8 PARKING THE MOWER  
1. Park the machine on a flat, level surface only. Do not  
park the machine on an incline.  
PULL UP TO ENGAGE  
2. Disengage the cutter blades.  
PUSH DOWN TO DISENGAGE  
3. Lock the neutral latches and shift the transmission  
into the neutral position.  
390S0138  
4. Slow the engine to idle speed.  
Figure 4-2. Cutter Engage Switch  
- NOTE -  
5. Turn the ignition key to the OFF position and remove  
the key.  
A squealing noise may be heard when engaging  
or disengaging the deck drive. It is caused by the  
electric clutch plates meshing as the mower comes  
up to speed. This is normal.  
4.9 AFTER OPERATION  
1. Wash the entire mower after each use. Do not  
use high pressure spray or direct the spray onto  
electrical components.  
3. To disengage the deck drive, push the switch in to  
the disengage position.  
- IMPORTANT -  
4. Always operate the engine at full throttle to properly  
maintain cutting speed. If the engine starts to lug  
down, reduce the forward speed and allow the  
engine to operate at maximum RPM.  
Do not wash a hot or running engine. Cold water  
will damage the engine. Use compressed air to  
clean the engine if it is hot.  
2. Keep the entire mower clean to inhibit serious heat  
damage to the engine or hydraulic oil circuit.  
4.7 HILLSIDE OPERATION  
3. Check the drive belts for proper alignment and any  
signs of wear. Correct and adjust if necessary.  
WARNING  
DO NOT operate on steep slopes. ALWAYS  
FOLLOW OSHA APPROvED OPERATION.  
DANGER  
To avoid injury from burns, allow the mower  
to cool before removing the fuel tank cap and  
refueling.  
1. This mower has been designed for good traction and  
stability under normal mowing conditions. However,  
caution must be used when traveling on slopes,  
especially when the grass is wet. Wet grass reduces  
traction and steering control.  
4. After the mower has cooled down, fill the fuel tank  
with fresh, clean fuel at the end of every day of  
operation. See Engine Owner's Manual for proper  
octane requirements.  
2. To prevent tipping or loss of control, do not start or  
stop suddenly, avoid unnecessary turns and travel  
at reduced speed. If tires lose traction, disengage  
blades and proceed slowly off the slope.  
5. Check the tire pressure. Adjust pressure if  
necessary.  
3. Avoid sudden starts when mowing on slopes.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 4  
3. Cut grass when it is dry and not too tall. Do not cut  
grass too short (cut off 1/3 or less of existing grass  
for best appearance). Mow frequently.  
4.10 REMOvING CLOGGED MATERIAL  
4. Keep mower and discharge chute clean.  
DANGER  
5. When mowing wet or tall grass, mow the grass twice.  
Raise the mower to the highest setting for the first  
pass and then make a second pass to the desired  
height.  
ROTATING BLADES  
NEvER PUTYOUR HANDS INTOTHE DISCHARGE  
CHUTE FOR ANY REASON!  
6. Use a slow travel speed for trimming purposes.  
7. Operate the engine at full throttle for best cutting.  
Mowing with a lower RPM causes the mower to tear  
the grass. The engine is designed to be operated at  
full speed.  
Shut off the engine and remove the key and  
only then use a stick or similar object to remove  
material if clogging has occurred.  
8. Use the alternate stripe pattern for best lawn  
appearance. Vary the direction of the stripe each  
time the grass is mowed to avoid wear patterns in  
the grass.  
1. If the discharge chute becomes clogged, shut off  
the engine and remove the ignition key. Using a stick  
or similar item, dislodge the clogged material. Then  
resume normal mowing.  
4.11 MOvING MOWER WITH ENGINE  
STOPPED  
To “free-wheel” or move the mower around without the  
engine running, engage the neutral latches, shift the  
transmission to neutral and move the mower by hand.  
4.12 RECOMMENDATIONS FOR MOWING  
1. Do not mow with dull blades. A dull blade will tear  
grass, resulting in poor lawn appearance and  
reduced mowing power.  
WARNING  
DO NOT operate without Discharge Chute,  
Mulching Kit, or entire Grass Catcher properly  
installed.  
2. The discharge chute must not be removed and  
must be kept in the lowest position to deflect grass  
clippings and thrown objects downward. Direct the  
side discharge away from sidewalks or streets to  
minimize cleanup of clippings. When mowing close  
to obstacles, direct the discharge away from the  
obstacles to reduce the chance of property damage  
by thrown objects.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 5  
TROUBLESHOOTING CUTTING CONDITIONS  
CONDITION  
CAUSE  
CURE  
STRINGERS - OCCASIONAL  
BLADES OF UNCUT GRASS  
Low engine RPM  
Run engine at full RPM  
Ground speed too fast  
Slow speed to adjust for conditions  
Cut grass after it has dried out  
Sharpen blades  
Wet grass  
Dull blades, incorrect sharpening  
Deck plugged, grass accumulation  
Clean underside of deck  
Width of Deck  
Belts slipping  
Adjust belt tension  
SGB020  
STREAKING - STRIPS OF  
UNCUT GRASS IN CUTTING  
PATH  
Dull, worn blades  
Incorrect blade sharpening  
Low engine RPM  
Sharpen blades  
Sharpen blades  
Run engine at full RPM  
Adjust belt tension  
Belt slipping  
Deck plugged, grass accumulation  
Ground speed too fast  
Wet grass  
Clean underside of deck  
Slow speed to adjust for conditions  
Cut grass after it has dried out  
Replace blades  
Width of Deck  
SGB018  
Bent blades  
STREAKING - STRIPS OF  
UNCUT GRASS BETWEEN  
CUTTING PATHS  
Not enough overlapping between rows Increase the overlap of each pass  
Width  
of  
Deck  
Width  
of  
Deck  
SGB019  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 5  
TROUBLESHOOTING CUTTING CONDITIONS (CONT'D)  
CONDITION  
CAUSE  
CURE  
UNEvEN CUT ON FLAT  
GROUND - WAvY HIGH-LOW  
APPEARANCE, SCALLOPED  
CUT, OR ROUGH CONTOUR  
Lift worn from blade  
Replace blade  
Blade upside down  
Mount with cutting edge toward ground  
Clean underside of deck  
Deck plugged, grass accumulation  
Too much blade angle (deck pitch)  
Deck mounted improperly  
Bent spindle area  
Adjust pitch and level  
See your authorized SCAG dealer  
See your authorized SCAG dealer  
Sharpen blade  
Width of Deck  
Dull blade  
SGB020  
UNEvEN CUT ON UNEvEN  
GROUND-WAvYAPPEARANCE,  
HIGH-LOW SCALLOPED CUT,  
OR ROUGH CONTOUR  
May need to reduce ground speed, raise  
cutting height, and/or change direction  
of cut  
Uneven ground  
Width of Deck  
SGB021  
SLOPING RIDGE ACROSS  
WIDTH OF CUTTING PATH  
Tire pressures not equal  
Wheels uneven  
Check and adjust tire pressure  
Check and adjust tire pressure  
See your authorized SCAG dealer  
Deck mounted incorrectly  
Deck not level side-to side  
Check for level and correct  
Width of Deck  
SGB023  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
Section 5  
TROUBLESHOOTING CUTTING CONDITIONS (CONT'D)  
CONDITION  
CAUSE  
CURE  
SCALPING - BLADES HITTING  
DIRTORCUTTINGvERYCLOSE  
TO THE GROUND  
Low tire pressures  
Check and adjust pressures  
Ground speed too fast  
Cutting too low  
Slow speed to adjust for conditions  
May need to reduce ground speed, raise  
cutting height, change direction of cut,  
and/or change pitch and level  
May need to reduce ground speed, raise  
cutting height, and/or change direction  
of cut  
Rough terrain  
Width of Deck  
Ground speed too fast  
Wet grass  
Slow speed to adjust for conditions  
Cut grass after it has dried out  
Adjust pitch and level  
SGB022  
STEP CUT - RIDGE IN CENTER  
OF CUTTING PATH  
Blades not mounted evenly  
Bent blade  
Replace blade  
Internal spindle failure  
See your authorized SCAG dealer  
Mounting of spindle incorrect  
See your authorized SCAG dealer  
Width of Deck  
SGB024  
SLOPECUT-SLOPINGRIDGES  
ACROSS WIDTH OF CUTTING  
PATH  
Bent spindle mounting area  
Internal spindle failure  
See your authorized SCAG dealer  
See your authorized SCAG dealer  
Bent deck housing  
See your authorized SCAG dealer  
Width of Deck  
SGB025  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
Section 6  
ADJUSTMENTS  
6.1 DRIvE CONTROL ADJUSTMENTS  
6.3 CUTTER DECK BELT ADJUSTMENTS  
1. Adjust the steering control rods so that there is  
approximately 3/4" clearance from the bottom of the  
rod to the bottom of the neutral latch slot when in the  
drive position. See Figure 6-1.  
WARNING  
Before removing any guards, shut the engine off  
and remove the ignition key. Wait for all moving  
parts to come to a complete stop before beginning  
work.  
2. Adjust the steering brake rods so that the brakes do  
not apply until the steering levers are pulled tight to  
the handles. When the steering levers are locked in  
the neutral position the machine should move freely.  
Neutral  
Latch  
1. Remove the belt cover.  
2. Adjust the cutter deck drive belt using a belt tension  
gauge. Adjust the belt so that the belt moves 1/2"  
with 10 pounds of pressure. Adjust the tension by  
tightening or loosening the J-bolt. See Figure 6-2.  
Neutral Lock  
Position  
"J" Bolt  
End Of L-Shaped  
Bracket  
Nut  
Drive Position  
Belt  
3/4"  
Washer  
Steering  
Brake Lever  
SC404GB05  
Figure 6-1. Steering Control Rod Adjustment  
- NOTE -  
SC400G  
CUTTER DECK DRIVE BELT TENSION  
ALIGNMENT IDLER - L.H.  
Operator pressence lever removed for clarity.  
Never operate equipment with the interlock system  
disconnected.  
Figure 6-2. Deck Drive Belt Adjustment  
-NOTE-  
Due to initial belt stretch and to prevent the belt  
from slipping, check this adjustment after the first  
2 hours, 4 hours and 8 hours of operation.  
6.2 THROTTLE CONTROL AND CHOKE  
ADJUSTMENTS  
3. Adjust the RH blade drive belt using a belt tension  
gauge. Adjust the belt so that the belt moves 1/2"  
with 10 pounds of pressure. Adjust the tension by  
tightening or loosening the J-bolt. See Figure 6-3  
and Figure 6-4.  
These adjustments must be performed by your Scag dealer  
to ensure proper and efficient running of the engine.Should  
either need adjustment, contact your authorized Scag  
service center.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 6  
BELT  
Changes to the cutting height can be acheived by  
repositioning the cutter deck. (This adjustment will also  
effect the pitch of the deck). There are three available  
positions. See Figure 6-5.  
WASHER  
NUT  
Caster spacers also can be repositioned to change the  
cutting heights and to change the pitch of the cutter deck.  
See Figure 6-6.  
SC401G  
LOW CUT (1-3/4" to 3")  
Figure 6-3. Cutter Deck Belt Adjustment R.H.  
MID RANGE  
(2-1/2" to 3-3/4")  
BELT TENSION  
ADJUSTMENT IDLER  
HIGH CUT  
(3-1/4" to 4-1/2")  
DISCHARGE  
AREA  
CHECK BLADE DRIVE  
BELT TENSION HERE  
Figure 6-5. Adjusting Cutting Height  
SC402G Rev.2  
Pin  
Spacers  
Figure 6-4. Cutter Deck Belt  
6.4 BELT ALIGNMENT  
Belt alignment is important for proper performance of  
your Scag mower. If you experience frequent belt wear  
or breakage, see your authorized Scag service center for  
belt adjustment.  
2003SGB005  
6.5 ADJUSTING CUTTING HEIGHT  
Figure 6-6. Cutting Height Decal  
The mower deck can be adjusted from a height of 1-3/4  
inches to 4-1/4 inches at 1/4-inch intervals.  
BLADE HEIGHT ADJUSTMENT  
Due to many cutting conditions that exist, it is difficult to  
suggest a cutter deck setting that will work for every lawn.  
There are two adjustments that can be made to the cutter  
deck, pitch and height.  
Adjusting the blade height can be done by moving any  
number of the five smaller 1/4" spacers on the blade  
mounting bolts to the top of the spindle shaft or below the  
spindle shaft.  
PITCH is the angle of the blades (comparing front to  
rear).  
-NOTE-  
All blades should be positioned equally.  
HEIGHT is the nominal distance the blade is off of the  
ground.This measurement is made with the blades pointed  
side to side and distance is measured between the cutting  
tip and ground. (Also see Blade Height Adjustment).  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 6  
CUSTOM-CUT BAFFLE ADJUSTMENT  
WARNING  
Blades have a sharp cutting edge. Wear proper  
eye protection and protective gloves or wrap the  
blades with protective material when removing,  
sharpening and installing blades.  
The Custom-Cut Baffle is designed to deliver optimum  
airflow and superior cutting performance in any type of  
grass. The Custom-Cut Baffle can be raised or lowered  
to precisely tailor the deck's performance for the type of  
grass being cut.The baffle can be set in seven (7) different  
positions for optimum performance.  
A. 3-1/2" or 3-3/4" Position - (See Figure 6-8).For very  
tall, wiry or tough-to-cut grass.  
For best cut and discharge, a minimum of three spacers  
should be installed between the blade and the spindle.  
See Figure 6-7.  
B. 4" (factory setting), 4-1/4" or 4-1/2" Position - (See  
Figure 6-8).For general purpose cutting.This gives the  
best mix of cutting performance in all types of grass.  
C. 4-3/4" or 5-1/4" Position - (See Figure 6-8).Placing  
the baffle in either the 4-3/4" or 5-1/4" setting will  
enhance fall cutting (leaf pickup) and reduce cutter  
deck "blowout".  
To adjust the Custom-Cut Baffle height:  
1. Place the cutter deck in the transport position.  
2. Remove the hardware securing the Custom-Cut  
Baffle to the cutter deck.  
- NOTE -  
Hardware location used in the illustrations are for  
reference only. Location of hardware may vary  
depending on cutter deck size.  
2002 SC407G  
3. Move the Custom-Cut Baffle to desired position.  
(See Figures 6-8).  
Figure 6-7. Blade Spacers  
4. Reinstall the mounting hardware. Torque hardware to  
39 ft-lbs.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
Section 6  
1
3
2
4
A
B
1
3
2
4
A
B
Custom-Cut Baffle Adjustment  
Mounting Slot Selected  
Mounting Hardware Location  
Slot “A”  
Height (inches)  
Hole 1  
3-3/4”  
Hole 2  
4-1/4”  
Hole 3  
4-3/4”  
Hole 4  
5-1/4”  
Slot “B”  
Height (inches)  
Hole 2  
3-1/2”  
Hole 3  
4”  
Hole 4  
4-1/2”  
Figure 6-8. Custom-Cut Baffle Adjustment  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
Section 6  
6.6 ELECTRIC CLUTCH ADJUSTMENT  
ADJUSTMENT NUTS  
The electric clutch serves two functions in the operation of  
the mower. In addition to starting and stopping the power  
flow to the cutter blades, the clutch also acts as a brake to  
assist in stopping blade rotation when the PTO is switched  
off or the operator presence circuit is interrupted.  
When the clutch is disengaged, the air gap between the  
armature and rotor must be adjusted to fifteen thousandths  
of an inch, 0.015, for proper operation. The airgap  
adjustment is made at three bolts on the clutch.There are  
three inspection windows, one next to each adjusting bolt.  
See Figure 6-3.  
INSPECTION WINDOW (x3)  
ADJUSTMENT NUTS  
Figure 6-11. Clutch Air Gap Adjustment  
Figure 6-9. Clutch Air Gap Adjustment  
This adjustment should be done every 500 hours of  
operation or annually, whichever comes first. In cases  
where the machine is heavily used, airgap settings should  
be checked more often.  
1. Locate the inspection windows on the clutch.  
2. Place a 0.015 feeler gauge in the slot between the  
rotor and the armature. See Figure 6-4.  
If the air gap is too narrow, the clutch armature may drag  
when disengaged, resulting in premature failure.  
INSERT 0.015 FEELER GAUGE HERE  
If the air gap is too wide, the clutch may be slow to engage  
as the magnet must pull the armature in from a greater  
distance.  
Figure 6-10. Clutch Air Gap Adjustment  
3. Tighten or loosen the adjusting bolt as needed to  
acheive the 0.015 inch airgap. See Figure 6-5.  
Perform this operation at all three inspection  
windows.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 7  
MAINTENANCE  
7.1 MAINTENANCE CHART - RECOMMENDED SERvICE INTERvALS  
HOURS  
PROCEDURE  
BREAK-IN  
(FIRST 10)  
COMMENTS  
8
20  
40 100 200 500  
Check all hardware for tightness  
X
Check all belts for proper See paragraph 7.6  
alignment  
X
Check engine oil level  
See paragraph 7.3  
X
X
X
X
X
X
X
X
*Clean mower  
Check tire pressure  
*Clean air filter element  
Check condition of blades  
Sharpen cutter blades  
Check tire pressure  
Check belt tension  
See paragraph 7.8  
See paragraph 7.5  
See paragraph 7.7  
See paragraph 7.7  
See paragraph 7.10  
See paragraph 6.3  
Check the operator interlock See paragraph 4.2  
system  
X
Change engine oil and filter  
See paragraph 7.3  
See paragraph 7.6  
X
Grease spindle bearings  
X
X
X
X
Check belts for proper alignment  
Check all belts for proper  
alignment  
*Replace engine air filter  
See engine operator's  
manual  
Grease caster wheel bearings  
Grease transmission couplers  
Check all hardware for tightness  
Change engine oil  
See paragraph 7.2  
X
X
X
X
X
See paragraph 7.2  
See paragraph 7.3  
See paragraph 7.5  
*Clean air cleaner element  
* Perform these maintenance procedures more frequently under extreme dusty or dirty conditions  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 7  
MAINTENANCE CHART - RECOMMENDED SERvICE INTERvALS (CONT'D)  
HOURS  
PROCEDURE  
BREAK-IN  
(FIRST 10)  
COMMENTS  
8
40  
100  
200  
500  
Check hardware for tightness  
Change engine oil filter  
X
X
See paragraph 7.3  
See paragraph 7.3  
Replace engine fuel filter  
X
X
X
Grease caster wheel pivot See paragraph 7.2  
shafts  
Adjust electric PTO clutch  
See paragraph 6.6  
7.2 LUBRICATION  
GREASE FITTING LUBRICATION CHART  
NO. OF  
PLACES  
LOCATION  
LUBRICATION INTERvAL  
LUBRICANT  
1 - Caster Wheel Pivot  
2 - Caster Wheel Bearings  
3 - Cutter Deck Spindles  
4 - Transmission Couplers  
5 - Wheel Bearings  
100 Hours / Bi-Weekly  
100 Hours/Monthly  
40 Hours / Weekly  
Chassis Grease  
Chassis Grease  
2
2
+ US Lithium MP White Grease  
Chassis Grease  
2 / 3  
2
100 Hours / Monthly  
100 Hours / Bi-Weekly  
100 Hours / Bi-Weekly  
Chassis Grease  
2
6 - Idler Arm Pivot  
Chassis Grease  
2
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 7  
GREASE FITTING LUBRICATION  
LUBRICANT / INTERVAL  
LITHIUM MP WHITE GREASE 2125  
( 40 HOURS / WEEKLY )  
CHASSIS GREASE  
( 100 HOURS / BI-MONTHLY )  
CHASSIS GREASE  
( 200 HOURS / MONTHLY )  
3
1
6
5
2
3
1
4
6
2
5
390S0178  
Figure 7-1. Lubrication Fitting Points  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
Section 7  
1. Extinguish all cigarettes, cigars, pipes and other  
7.3 ENGINE OIL  
sources of ignition.  
2. Use only an approved gasoline container.  
A. CHECKING ENGINE CRANKCASE OIL LEvEL  
3. Never remove the gas cap or add fuel with the  
engine running. Allow the engine to completely cool  
before fueling.  
The engine oil level should be checked after every 8 hours  
of operation or daily as instructed in the Engine Operator’s  
Manual furnished with this mower.  
4. Never fuel the machine indoors or in an enclosed  
trailer.  
B. CHANGING ENGINE CRANKCASE OIL  
5. Never store the machine or fuel container where  
there is an open flame, spark or pilot light such as on  
a water heater or other appliances.  
After the first 20 hours of operation, change the engine  
crankcase oil and replace the oil filter. Thereafter,  
change the engine crankcase oil after every 100 hours  
of operation or bi-weekly, whichever occurs first. Refer to  
the Engine Operator’s Manual furnished with this mower  
for instructions.  
6. Never fill containers inside a vehicle or on a truck  
or trailer bed with a plastic liner. Always place  
containers on the ground away from your vehicle  
before filling.  
7. Remove the machine from the truck or trailer and  
fuel on the ground. If this is not possible, then refuel  
the machine with a portable container, rather than  
from a gasoline dispenser nozzle.  
C. CHANGING ENGINE OIL FILTER  
After the first 20 hours of operation, replace the engine oil  
filter.Thereafter, replace the oil filter after every 200 hours  
of operation or every month, whichever occurs first. Refer  
to Engine Operator’s Manual for instructions.  
8. Keep the nozzle in contact with the rim of fuel tank  
or container opening at all times until fueling is  
complete. Do not use a nozzle lock-open device.  
9. If fuel is spilled on clothing, change clothing  
immediately and wash affected skin.  
7.4 ENGINE FUEL SYSTEM  
10. Replace gas cap and tighten securely.  
DANGER  
B. REPLACING IN-LINE FUEL FILTER  
ELEMENTS  
To avoid injury from burns, allow the mower  
to cool before removing the fuel tank cap and  
refueling.  
The engine fuel filter should be replaced after every 500  
hours of operation or annually, whichever occurs first.  
1. Close the shut-off valve.  
A. FILLING THE FUEL TANK  
2. Remove and replace the engine fuel filter. Open the  
fuel shut-off valve.  
Fill the fuel tank at the beginning of each operating day  
to within one (1) inch below the filler neck. Do not overfill.  
Use clean, fresh unleaded gasoline with a minimum octane  
rating of 87 and a maximum of 10% Ethanol.  
DO NOT use E85 Fuel. Using E85 Fuel will cause severe  
damage to the engine.  
To avoid personal injury or property damage, use extreme  
care in handling gasoline.Gasoline is extremely flammable  
and the vapors are explosive.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 7  
4. If a blade cutting edge is dull or nicked, it should be  
sharpened. Remove the blades for sharpening. See  
"Blade Replacement."  
7.5 ENGINE AIR CLEANER  
A. CLEANING AND/OR REPLACING AIR  
CLEANER ELEMENT  
- NOTE -  
Keep the blades sharp.Cutting with dull blades not  
only yields a poor mowing job, but slows the cutting  
speed of the mower and causes extra wear on the  
engine and the blade drive by pulling hard.  
For any air cleaner, the operating environment dictates  
the air cleaner service periods. Inspect and clean the air  
cleaner element after every 100 hours of operation or bi-  
weekly, whichever occurs first and replace the element if  
required.  
B. BLADE SHARPENING  
- NOTE -  
- NOTE -  
In extremely dusty conditions it may be necessary  
to check the element once or twice daily to prevent  
engine damage.  
If possible, use a file to sharpen the blade. Using  
a wheel grinder may burn the blade.  
1. Remove the air cleaner cover. Set aside.  
2. Remove the air cleaner and inspect.  
- NOTE -  
DO NOT sharpen the blades beyond 1/3 of the  
width of the blade. See Figure 7-2.  
3. Clean or replace the air cleaner and foam  
pre-cleaner as recommended by the engine  
manufacturer.  
1. Sharpen the cutting edge at the same bevel as the  
original. See Figure 7-2. Sharpen only the top of the  
cutting edge to maintain sharpness.  
4. Replace the air cleaner cover and secure.  
Angle Blade Back  
7.6 CUTTER BLADES  
Do Not Cut In  
A. BLADE INSPECTION  
1. Remove the ignition key before servicing the blades.  
x
2. Raise the mower deck to the highest position. Place  
the lanyard pin in the highest cutting height position  
to prevent the cutter deck from falling.  
X Must NOT Exceed  
1/3 Blade Width  
30  
SGB033  
Figure 7-2. Blade Sharpening  
2. Check the balance of the blade. If the blades are out  
of balance, vibration and premature wear can occur.  
See your authorized Scag dealer for blade balancing  
or special tools, if you choose to balance your own  
blades.  
WARNING  
Always wear proper hand and eye protection when  
working with cutter blades.  
3. Check the cutter blades for straightness. If the cutter  
blades appear bent, they will need to be replaced.  
WARNING  
Do not attempt to straighten a bent blade, and  
never weld a broken or cracked blade. Always  
replace it with a new blade to assure safety.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 7  
C. BLADE REPLACEMENT  
7.7 TIRES  
Check the tire pressures after every 8 hours of operation  
or daily.  
WARNING  
Always wear proper hand and eye protection when  
working with cutter blades.  
Caster Wheels  
Drive Wheels  
Flat-Free  
12 PSI  
1. Remove the ignition key before replacing the blades.  
2. Remove the belt cover.  
3. Secure the cutter blades to prevent them from  
rotating, (use the optional Blade Buddy tool P/N  
9212, to assist in securing the cutter blades), remove  
the blade attaching bolt. Remove the cutter blade,  
bolt, lockwasher and flatwasher from the spindle  
shaft. See Figure 7-3.  
- NOTE -  
Be sure that the blade is installed with the lift wing  
towards the top of the cutter deck.  
4. Install the cutter blade on to the cutter spindle shaft.  
Secure the blades from rotating and torque to 75 ft/  
lbs. See Figure 7-3.  
5. Install the belt cover.  
HEX NUT-TORQUE  
TO 75 LB-FT  
SPINDLE  
SHAFT  
CUTTER  
DECK  
HEX HEAD  
BOLT / NUT  
SPINDLE  
ASSEMBLY  
CUTTER BLADE  
SPACERS  
CUTTER  
BLADE  
WASHER  
HEX HEAD BOLT  
Figure 7-3. Blade Replacement  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 8  
ILLUSTRATED PARTS LIST  
8.1 SCAG APPROvED ATTACHMENTS AND ACCESSORIES.  
Attachments and accessories manufactured by companies other than Scag Power Equipment are not approved  
for use on this machine.  
Scag approved attachments and accessories:  
• Mulch Plate (p/n 9258, 9286, 9287)  
• Hurricane Mulch (p/n 9263, 9283, 9284)  
• GC-4D (p/n 9054)  
• GC-F4 (p/n 9055)  
• Blade Buddy (p/n 9212)  
• Hour Meter (p/n 48023  
• Turbo Baffle (p/n 424208)  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 8  
32" & 36A CUTTER DECKS  
55  
24  
63  
25  
29  
28  
27  
28  
29  
52  
55  
45  
11  
27  
11  
24  
42  
53  
30  
30A  
41  
52  
37  
44  
26  
A
25  
23  
23A  
42  
26  
32  
34  
7
38  
40  
13  
21  
9
33  
36  
20  
22  
20A  
35  
33  
A
2
19  
18  
1
1A  
21  
31  
56  
39  
24  
60  
14  
59  
8
61  
55  
46  
57  
62  
5
43  
10  
58  
50  
54  
6
11  
3
12  
11  
48  
47  
15  
15A  
5
16  
51  
49  
17  
SW06CD36A  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 8  
32" & 36A CUTTER DECKS  
Ref.  
Ref.  
No.  
Part No.  
No.  
Description  
32  
36  
Part No.  
Description  
32  
36  
45  
46  
47  
48  
49  
50  
51  
52  
53  
483215  
481024  
43297  
43296  
481035  
48677  
481025  
48098  
04029-04  
Idler Pulley, Belt Clutch  
Seal, Cutter Spindle  
Spindle Bushing  
Spacer, Inside  
Nut,1.06-18  
Relief Fitting, Cutter Spindle  
Seal, Cutter Spindle  
Spindle Shield  
Wing Nut, 3/8-16 (Small)  
RH side  
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
1
1A  
2
3
5
6
7
8
9
461847  
461848  
461663  
43312  
481022  
43644  
04001-154  
43589  
04001-51  
Cutter Deck w/Decals  
Cutter Deck w/Decals  
Cutter Spindle Assembly  
Spacer, Outside  
Bearing, Tapered  
Spindle Housing  
Bolt, 5/16-18 x 4-3/4"  
Spindle Shaft  
Bolt, 3/8-16 x 3-3/4" Hex  
Head  
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
54  
55  
56  
57  
58  
59  
60  
61  
62  
48114-04  
04021-09  
04030-03  
04003-23  
423783  
Grease Fitting  
x
x
x
x
x
x
x
x
x
x
x
x
x
10  
11  
12  
04063-08  
43592  
04001-175  
Key, 1/4 x 1/4 x 2"  
Spacer, Cutter Blade - Small  
Bolt, 5/16-18 x 1-1/2" Hex  
Head Grade 8  
Spring, Chute Return  
Nut 5/16-18 Serrated Flange  
Cutter Blade, 16-1/2"  
Cutter Blade, 18"  
Cutter Blade 16-1/2 Hi-Lift  
Cutter Blade, 18 Hi-Lift  
Flatwasher, 5/8 W  
Hex Hd. Bolt, 5/8-11 x 9-1/2"  
Caster Assembly  
x
x
x
x
x
x
Nut, Hex Elastic Stop 3/8-16  
Lock Washer, 5/16"  
Bolt, Carriage 3/8-16 x 1"  
Baffle Weldment  
13  
14  
15  
482245  
04019-03  
481706  
481707  
481710  
x
x
x
x
x
483174  
Pad, Deck Wear  
x
x
x
x
04003-12  
04040-04  
04021-04  
Bolt, Carriage 5/16-18 x 3/4"  
Flatwasher, 5/16"  
Hex Nut, 5/16-18 Center  
Locknut  
x
15A  
x
481711  
x
x
x
x
x
63  
424367  
Dust Shield  
x
x
16  
17  
18  
19  
04043-06  
04001-41  
461023  
x
x
x
x
04017-16  
Cpscrw,5/16-18 x 3/4" Ser.  
Flg. Hex Head  
20  
20A  
21  
461291  
461295  
04021-10  
Discharge Chute  
Discharge Chute  
Hex Nut, 5/16-18 Elastic  
Stop  
x
x
x
x
22  
23  
23A  
24  
25  
26  
27  
28  
29  
30  
30A  
31  
04001-09  
461709  
461413  
04043-04  
04029-03  
482744  
Hex Hd Bolt, 5/16-18 x 1"  
Belt Cover Assy (Incl. Decal)  
Belt Cover Assy (Incl. Decal)  
Flat Washer, 3/8" Special  
Wing Nut, 3/8-16  
Pulley  
Tapered Hub  
Hex Hd. Bolt, 1/4-20 x 1"  
Hex Nut, 5/8-11  
Belt, Blade Drive  
Belt, Blade Drive  
Elastic Stop Nut, 5/16-18  
Grade 8  
Hex Nut, 3/8-16 Center  
Locknut  
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
48926  
04001-172  
04020-09  
48278  
48204  
04021-22  
x
x
x
x
32  
04021-05  
x
33  
34  
35  
04019-04  
04004-02  
04017-36  
Nut, 3/8-16 Serrated Flange  
Support, Belt Cover  
Cpscrw, 1/2-13 x 1"Ser.Flg.  
HH  
x
x
x
x
x
x
36  
37  
38  
04112-05  
43277  
04041-12  
Nut, 1/2-13 Spiralock  
Spacer, J-Hook  
Flatwasher, 3/8 x 1-1/2 x  
16 GA  
x
x
x
x
x
x
39  
40  
41  
42  
43  
04021-09  
43681  
461841  
48224  
Elastic Stop Nut, 3/8-16  
Idler Pivot  
Idler Arm Assy. (Inc. 42)  
Bearing  
Cpscrw, 3/8-16 x 3-1/4" Hex  
Head  
x
x
x
x
x
x
x
x
x
x
04001-62  
44  
44078  
J-Hook  
x
x
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
Section 8  
48v & 52v CUTTER DECKS  
50  
25  
19  
58  
26  
36  
25  
62  
29  
74  
43  
30  
11  
30  
29  
28  
36  
29  
30  
33  
28  
45  
11  
32  
4
25  
24  
11  
28  
26  
47  
62  
48  
49  
36  
36  
25  
74  
31  
13  
26  
36  
34  
67  
9
61  
4
37  
35  
22  
25  
62  
52  
27  
21  
53  
23  
40  
39  
A
36  
25  
62  
42  
75  
20  
4
22  
A
60  
72  
73  
18  
59  
1
69  
14  
8
2
14  
51  
46  
41  
65  
38  
64  
44  
5
63  
70  
10  
54  
7
36  
6
11  
55  
68  
12  
11  
3
71  
15  
15A  
5
16  
56  
66  
57  
17  
SW-06CD48V-52V  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 8  
48v & 52v CUTTER DECKS  
Ref.  
Ref.  
No.  
Part No.  
No.  
Description  
48  
52  
Part No.  
Description  
48  
52  
45  
46  
47  
48  
49  
50  
461091  
483176  
43028  
43077  
04041-12  
04001-31  
Idler Arm Assy. (Incl. 62)  
Pad, Deck Wear  
J-Rod, Idler Pulley  
Spacer, J-Rod  
Washer, 3/8 x 1-1/2 x 16 ga.  
Bolt, 3/8-16 x 2-1/2" Hex  
Head  
Seal, Cutter Spindle  
Idler Arm Assy (Includes 62)  
Spacer, J-Rod  
Reiief Fitting, Cutter Spindle  
Spacer, Outside, Cutter  
Spindle  
Spindle Bushing  
Nut, Cutter Spindle  
Knob, w/stud  
Bolt, 3/8-16 x 3-3/4" Hex  
Head  
Idler Pivot  
Idler Pulley, Belt Clutch  
Bearing  
Bolt, Carriage 5/16-18 x 3/4"  
Guide Roller  
Roller Shaft  
Seal, Cutter Spindle  
Spring, Chute Return  
Baffle Weldment 48V  
Baffle Weldment 52V  
Bolt, 3/8-16 x 3-1/4" Hex  
Head  
Bolt, Carriage 3/8-16 x 1"  
Heatshield  
Nut, Hex Lock 5/16-18  
Lock Washer 5/16"  
Dust Shield  
x
x
x
x
x
x
x
x
x
x
x
x
1
461852  
461855  
461663  
43296  
482744  
481022  
43644  
48114-04  
43589  
43682  
Cutter Deck w/Decals  
Cutter Deck w/Decals  
Spindle Assembly  
Spacer, Inside  
Pulley  
Tapered Bearing  
Spindle Housing  
Grease Fitting Str. 5/16"  
Spindle Shaft  
x
x
x
x
x
x
x
x
x
x
x
x
x
2
3
4
5
6
7
8
9
x
x
x
x
x
x
x
x
x
x
x
51  
52  
53  
54  
55  
481024  
461841  
43277  
48677  
43312  
x
x
x
x
x
x
x
x
x
x
Idler Pivot  
10  
11  
12  
04063-08  
43592  
04001-175  
Key, 1/4 x 1/4 x 2"  
Spacer, Cutter Blade - Small  
Bolt, 5/16-18 x 1-1/2" Hex  
Head Gr. 8  
Bolt, 5/16-18 x 4-3/4" Hex  
Head  
Serr. Flange Nut, 5/16-18  
Cutter Blade 16-1/2"  
Cutter Blade 18"  
Cutter Blade 16-1/2 Hi-Lift  
Cutter Blade 18 Hi-Lift  
Flatwasher,5/8" (.688 x 1.75  
x .134)  
56  
57  
58  
59  
43297  
481035  
481625-01  
04001-51  
x
x
x
x
x
x
x
x
13  
04001-154  
x
x
x
x
14  
15  
04019-03  
481706  
481707  
481710  
481711  
04043-06  
x
x
60  
61  
62  
63  
64  
65  
66  
67  
68  
43681  
483215  
48224  
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
15A  
16  
x
x
x
x
x
04003-12  
482295  
45944  
481025  
483378  
424839  
424840  
04001-62  
17  
04001-41  
Hex Head Bolt, 5/8-11 x  
9-1/2"  
Caster Assembly  
x
18  
19  
20  
21  
461023  
48098  
04017-16  
461844  
461845  
04021-10  
x
x
x
x
x
x
x
Spindle Shield  
x
x
Capscrew, 5/16-18 x 3/4"  
Discharge Chute 48V  
Discharge Chute 52V  
Nut, 5/16-18 Elastic Elastic  
Stop  
69  
x
x
x
70  
71  
72  
73  
74  
75  
04003-23  
423972  
04021-22  
04030-03  
424367  
x
x
x
x
x
x
x
x
x
x
x
x
22  
23  
24  
x
x
x
04001-11  
Bolt, 5/16-18 x 1-1/2" Hex  
Head  
x
461866  
461867  
04043-04  
04029-03  
04110-03  
48926  
Belt Cover (Incl. decals)  
Belt Cover (Incl. decals)  
Flat Washer, 3/8" Special  
Wing Nut, 3/8-16 (Large)  
U-Nut, 3/8-16  
Tapered Hub  
Bolt, 1/4-20 x 1" Hex Head  
Grade 8  
04001-22  
Bolt, 3/8-16 x 2-3/4" Hex  
Head  
x
x
x
x
x
x
25  
26  
27  
28  
29  
x
x
x
x
x
04001-172  
30  
31  
32  
04020-09  
482748  
48087  
48285  
48089  
Nut, 5/8-11 Hex  
Pulley, Double  
Belt, RH Blade Drive  
Belt, RH Blade Drive  
Belt, Blade Drive  
x
x
x
x
x
x
33  
x
483518  
Belt, Blade Drive  
x
x
x
x
x
x
x
34  
35  
36  
37  
38  
39  
04021-05  
04019-04  
04021-09  
04004-02  
04001-09  
04017-36  
Nut, 3/8-16, Nut Centerlock  
Nut, 3/8-16, Serrated Flange  
Nut, 3/8-16 Elastic Stop  
Bolt, 5/16-18 x 1" Hex Head  
Bolt, 5/16-18 x 1" Hex Head  
Cpscrw, 1/2-13 x 1" Ser.  
Flg. HH  
x
x
x
x
x
x
40  
41  
04112-05  
04021-04  
Nut, 1/2-13 Spiralock  
Hex Nut, 5/16-18 Center  
Locknut  
x
x
x
x
42  
44078  
J-Hook, 48V  
x
43028  
48181  
04040-04  
J-Hook, 52V  
Idler Pulley, “V” Groove  
Flatwasher, 5/16"  
x
x
x
43  
44  
x
x
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
Section 8  
NOTES  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 8  
CASTER ASSEMBLY  
1
2
3
4
3
2
5
6
8
7
9
10  
12  
11  
13  
SW-SWZ2006CSTR  
Ref.  
No.  
Part No.  
Description  
1
2
3
4
5
6
04066-01  
43037-01  
48100-01  
48114-04  
46082  
Quick Pin  
Spacer, Spacer Yoke, 1/2" Long  
Bronze Bearing  
Greasing Fitting  
Support Assembly (Incl. #3 & #4)  
Caster Yoke  
45006  
7
8
9
10  
11  
12  
13  
04021-07  
43022  
04001-37  
9275  
48114-03  
481770  
481769  
Nut, Elastic Stop 1/2-13  
Sleeve, Caster Wheel Bearing  
Bolt, Hex Head 1/2-13 x 5-1/2"  
Flat-Free Tire Assy. (Incl. #11, #12, #13)  
Grease Fitting, 45 Degree 1/4-28  
Retainer, Caster Wheel Bearing  
Roller Bearing, Caster Wheel  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 8  
ENGINE DECK  
4
34  
50  
5
15 KAI  
16 KAI  
17 KAI  
ONLY  
3
5A  
7
6
52  
8
9
18  
1
10  
(3)  
12  
13  
(1 loc.)  
42  
44  
46  
40  
11  
43  
45  
17  
41  
40, 40A  
A
15  
16  
37  
20  
24  
23  
27  
29  
28  
39  
A
33  
25  
49  
26  
22  
39  
38  
38A  
38B  
38C  
38D  
21  
48  
35  
B
30  
31  
2
14  
32A  
32B  
47  
54  
51  
2
53  
B
SW2008ED  
47  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 8  
ENGINE DECK  
15KAI  
16KAI  
17KAI  
15KAI  
16KAI  
17KAI  
Ref.  
Ref.  
No.  
15KH  
15KH  
Part No.  
No.  
Description  
Part No.  
Description  
29  
30  
31  
32A  
04063-19  
04041-28  
04030-05  
04102-04  
Key, 1/4 x 1/4 x 3/4"  
Flat Washer, 7/16" Special  
Lock Washer, 7/16"  
Bolt, 7/16-20 x 2-1/2" Hex  
Head  
Cpsrw, M10-1.5 x55 Metric  
Hex Hd  
Bolt, 5/16-18 x 1-3/4" Hex  
Head  
Bolt, M8-1.25 x 1.0  
Nut, 3/8-16 Elastic Stop  
Flat Washer, 5/16"  
Bolt, M8-1.25 x M25 Metric  
Hex Hd  
Wheel Assembly (incl. 38A-  
38B) (fits SW36,48,52)  
Wheel Assembly (Incl. 38C -  
38D) (SW32)  
Tire, 13 x 6.50-6, 2-ply  
(fits SW36,48,52)  
Rim & Bearing Assembly  
(incl. 39)  
x
x
x
x
x
x
x
1
482853  
482675  
483263  
482927  
Engine,15HP Kohler  
(CV 15T, Spec PS-41621)  
Engine, 15HP Kawasaki  
(Spec FH430V-BS33-R)  
Engine, 16HP Kawasaki  
(Spec FH480V-BS24-R)  
Engine, 17HP Kawasaki  
(Spec FH541V-BS38-R)  
Cable Clamp  
Transmission, 5-speed  
(Peerless 700-070, 9 tooth  
spline)  
Neutral Safety Switch  
Fibre Washer, thin  
Fibre Washer, thick  
Coupler, Jackshaft  
Grease Fitting, straight  
1/4-28  
Jackshaft (fits SW32,36,48  
& 52)  
Key, Hi-Pro #9  
Bolt, 5/16-18 X 3/4" Hex  
Head  
Wheel Axle (SW36,48 & 52)  
Wheel Axle (SW 32)  
Muffler (Contact Engine  
Mfg.)  
x
x
x
x
32B  
33  
04103-03  
04001-12  
x
x
x
2
3
48030-09  
481580  
x
x
x
x
34  
35  
36  
37  
04002-07  
04021-09  
04040-15  
04018-01  
x
x
x
x
x
x
4
5
5A  
6
7
48231  
x
x
x
x
x
x
x
x
x
x
48122-01  
48122-02  
481581  
38  
48192  
x
x
x
x
x
x
x
48253  
48114-05  
38A  
38B  
38C  
38D  
481860  
481859  
481861  
481862  
x
x
8
481582  
x
x
9
10  
04063-09  
04017-16  
x
x
x
x
Tire, 13 x 5.00-6 2-ply  
(SW32 only)  
Rim Assembly (incl. 39)  
(SW32 only)  
Wheel Bearing  
Washer, 1-1/16 x 1-3/4 x  
12 ga  
11  
12  
13  
43085**  
43104**  
x
x
x
x
x
x
39  
40  
481858  
04042-05  
x
x
x
x
04001-08  
Bolt, 5/16-18 X 3/4" Hex  
Head  
x
40A  
04041-14  
Washer, 1-1/16 x 1-1/2 x  
18 ga  
Retaining Ring, 1" Ext.- "E"  
Pulley, Wheel Drive  
Spacer, Wheel Pulley  
Brake Drum  
x
x
14  
15  
16  
17  
422533  
Backing Plate  
Lock Wshr. 5/16"  
x
x
x
x
x
x
x
x
04030-03  
04019-04  
461741  
41  
42  
43  
44  
45  
04050-08  
48200  
43088  
48209  
04017-19  
x
x
x
x
x
x
x
x
x
x
Nut, 3/8-16 Serrated Flange  
Engine Deck (fits SW32)  
Engine Deck (fits SW36,48  
& 52)  
Nut, 1/4-20 Elastic Stop  
Nut, 5/16-18 Serrated  
Flange  
Bolt, 3/8-16 x 3-3/4" Hex  
Head  
Electric Clutch (Ogura)  
Washer, 3/8" (.391 x .938  
x .105)  
461743  
x
Bolt, 5/16-18 x 1-1/2"  
Serrated Flange  
18  
19  
04021-08  
04019-03  
x
x
x
x
46  
47  
48  
49  
50  
51  
52  
04003-03  
04021-10  
04003-04  
421370  
04031-09  
481716  
Bolt, 3/8-16 x 2" Carriage  
Nut, 5/16-18 Elastic Stop  
Bolt, 5/16-18 x 1" Carriage  
Anti Rotation Bracket  
Lock Washer Internal Tooth  
Rubber Pad, Clutch Stop  
Wire Harness Adapter  
(15KAI, 16KAI, 17KAI)  
Plate, Backing  
x
x
x
x
x
x
x
x
x
x
x
x
x
20  
04001-51  
x
x
21  
22  
461397  
04041-07  
x
x
x
x
481717  
23  
24  
25  
48197  
04063-07  
04050-09  
Pulley, Transmission Input  
Key, Woodruff #9  
Retaining Ring, 5/8" Ext,  
Basic  
x
x
x
x
x
x
53  
54  
422534  
424620  
x
x
x
x
Plate, Clutch Bracket  
26  
27  
28  
48203  
483208  
481666  
Belt, Transmission Drive  
Idler Pulley, Transmission  
Pulley, Traction Drive  
x
x
x
x
x
x
** = Requires welding onto chassis.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
Section 8  
HANDLE ASSEMBLY  
8
30  
64  
27  
8
7
26  
29  
66  
28  
25  
71  
72  
1
69  
63  
61  
70  
65  
20  
69  
68  
62  
23  
27 54  
43  
41  
58  
58A  
59  
43A  
19  
8
9
48  
47  
46  
50  
45  
3
55  
24  
11  
44  
49 51  
9
60  
10  
20  
53  
15  
15A  
14  
36  
12  
56  
52  
40  
16  
13  
57  
67  
22  
5
4
14  
19  
18  
17  
13  
31  
2
19  
21  
32  
37  
19  
35  
14  
39  
6
5
34  
19  
19  
45 22  
33  
38  
19  
SW 2007 HA  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 8  
HANDLE ASSEMBLY  
15KAI  
16KAI  
17KAI  
15KAI  
16KAI  
17KAI  
Ref.  
Ref.  
No.  
15KH  
15KH  
Part No.  
No.  
Description  
Part No.  
Description  
46  
47  
482645  
04012-04  
Pulley, Jackshaft (Inc. 47)  
Setscrew, Hex Socket Knurl  
Cup Pt. 5/16-18  
Spacer, Jackshaft Pulley  
Flange, Jackshaft Bearing  
Bearing, Jackshaft  
Retaining Ring, 5/8 Ext.  
Basic  
Lock Washer 5/16"  
Capscrew, 5/16-18 x 3/4"  
Serr. Flg.  
Bolt, 5/16-18 x 2" Hex Head  
Nut, 1/4-20 Serrated Flange  
Flatwasher, 5/16 (.375 x  
.875 x .083)  
Bracket, Choke Mounting  
Fuel Hose,1/4"ID, 10"  
(KH Only)  
Fuel Hose,1/4"ID, 23"  
(KA Only)  
Clamp, Fuel Hose  
Choke Control  
Plug, Handlebar  
Valve, Fuel Shut Off  
Fuel Tank Assy.(Incl. Bush.  
& Val.)  
Fuel Tank Cap  
Shift Lever  
Shift Lever Extention  
(incl. 72)  
Capscrew, 5/16-18 x 1" Hex  
Head  
Washer, 3/8 (.391x .938 x  
.105)  
x
x
x
x
1
2
3
461972  
421360  
04017-27  
Handle Assembly  
Belt Guard  
Capscrw, 3/8-16 x 1"  
Serr. Flg.  
Washer, 3/8" (.391 x .938  
x .105)  
Nut, 3/8-16 Elastic Stop  
Spring, Idler  
Bolt, 5/16-18 x 1-1/4" Hex  
Head  
Nut, 5/16-18 Elastic Stop  
Capscrew, 1/4-20 x 3/4" Hex  
Head  
Control Rod, Steering  
Hair Pin, Small  
Bolt, 3/8-16 x 4-1/2" Hex  
Head  
x
x
x
x
x
x
48  
49  
50  
51  
43098  
48223  
48224  
04050-09  
x
x
x
x
x
x
x
x
4
04041-07  
x
x
5
6
7
04021-09  
48755  
04001-10  
x
x
x
x
x
x
52  
53  
04030-03  
04017-16  
x
x
x
x
8
9
04021-10  
04017-05  
x
x
x
x
54  
55  
56  
04001-17  
04019-02  
04040-15  
x
x
x
x
x
x
10  
11  
12  
44140  
04062-02  
04001-23  
x
x
x
x
x
x
57  
58  
424113  
483617  
x
x
x
13  
14  
15  
15A  
16  
17  
18  
19  
20  
43032  
04062-01  
45847  
45846  
43092  
04001-62  
04004-17  
04019-04  
04019-03  
Swivel Joint  
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
58A  
483617  
Hair Pin, Large .094 Dia.  
Idler Bracket, RH  
Idler Bracket, LH  
Idler Sleeve  
Bolt, 3/8-16 x 3/4" Hex Head  
Stud, 3/8-16 x 5"  
Nut, 3/8-16 Serrated Flange  
Nut, 5/16-18 Serrated  
Flange  
Cpscrw, 3/16-18 x 1-1/4"  
Serr. Flg  
Spacer  
Bushing  
Steering Lever  
59  
60  
61  
62  
63  
48059-01  
482314  
483161  
48308  
x
x
x
x
x
x
x
x
x
461729  
64  
65  
66  
482547  
422279  
461163  
x
x
x
x
x
x
21  
04017-28  
x
x
22  
23  
24  
25  
43286  
48309  
483160  
04017-17  
x
x
x
x
x
x
x
x
67  
68  
04001-09  
04041-07  
x
x
x
x
Capscrew, 5/16-18 x 1" Serr.  
Flg.  
69  
70  
71  
72  
04020-14  
48028-05  
04001-53  
481839  
Nut, 3/8-24 UNF  
Cable Tie  
Bolt, 5/16-18 x 2-1/2"  
Grip, Shift Handle  
x
x
x
x
x
x
x
x
26  
27  
483142  
04040-15  
Bushing  
Washer, 5/16 (.375 x .875  
x .083)  
Spring, Operator Presence  
Operator Presence Lever,  
LH  
x
x
x
x
28  
29  
483040  
451915  
x
x
x
x
30  
451917  
Operator Presence Lever,  
RH  
x
x
31  
32  
33  
34  
35  
36  
44005  
45092  
45093  
42254  
04024-01  
48114-05  
Brake Rod  
Brake Lever  
Brake Link  
Brake Link Plate  
Nut, 3/8 Push-on  
Grease Fitting, Straight  
1/4-28  
x
x
x
x
x
x
x
x
x
x
x
x
37  
38  
39  
40  
04050-01  
48210  
04001-45  
04031-08  
Retaining Ring, 5/8 Ext. "E"  
Brake Band  
Bolt, 3/8-16 x 2" Hex Head  
1/4" Internal Tooth Lock-  
washer  
x
x
x
x
x
x
x
x
41  
42  
04032-01  
04015-13  
Socket Head Capscrew  
#8-32 x 1/2"  
Socket Head Capscrew #8-  
32 x 1/2"  
x
x
x
x
43  
43A  
44  
461242  
461241  
48202A  
483211  
Neutral Latch, RH  
Neutral Latch, LH  
Belt, Wheel Drive  
Idler Pulley, Wheel Drive  
x
x
x
x
x
x
x
x
45  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
Section 8  
INSTRUMENT PANEL  
3
9
7
2A  
2B  
6
5
4
1
8
SW08IP  
Ref.  
No.  
Part No.  
Description  
1
48717  
Switch, Neutral Lock  
2A  
2B  
3
482814  
48946  
483957  
48609  
Throttle Contro - Kohler  
Throttle Control - Kawasaki  
Engagement Switch, Electric Clutch  
Key Switch  
4
5
6
7
8
48023  
Hour Meter (dealer installed)  
Screw, #10-32 x 1/2"  
Nut, #10-32 Serrated Flange Hex Head  
Handle Wire Harness, Manual Start  
Key Chain w/Keys  
04010-26  
04019-01  
482711  
462069  
483609  
48030-09  
9
Key w/Shroud  
Clamp, Wire Harness  
NS  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 8  
PEERLESS TRANSMISSION 700-070  
FOR REFERENCE ONLY - ORDER PARTS FROM PEERLESS / TECUMSEH  
REF.  
NO. NO.  
PART  
DESCRIPTION  
Ref. Part  
No. No.  
Description  
50  
51  
52  
53  
56  
57  
58  
59  
60  
65  
66  
67  
71  
72  
81  
82  
83  
90  
778125  
Spur Rear (35 teeth)  
Spur Gear (32 teeth-steel)  
Spur Gear (30 teeth)  
Spur Gear (25 teeth)  
Spur Gear (12 teeth-steel)  
Spur Gear (15 teeth)  
Spur Gear (18 teeth-steel)  
Spur Gear (20 teeth)  
Spur Gear (25 teeth)  
Washer  
Input Shaft (3-11/16" long)  
Shifter & Brake Shaft  
1
2
772083A  
780086A  
Case, Transmisson  
Needle Bearing Grease Spec  
Needle Bearing  
Case, Transmission  
Shift Key  
778239A  
778124A  
778123A  
778145  
778151  
778240  
778126A  
778127A  
780139  
776135  
776402  
788069  
792074  
786081  
786082  
786083  
788067B  
2A 780142  
3
8
9
770061A  
792089A  
784266  
784376  
778154  
778176  
792077  
792078  
792079  
780071  
792073  
792035  
788040  
780072  
780108  
792001  
780105A  
778146A  
Shift Collar  
10  
11  
12  
20  
21  
22  
24  
25  
27  
28  
29  
30  
32  
34  
49  
Shift Rod & Fork  
Bevel Gear (42 teeth)  
Bevel Pinion (14 teeth-steel)  
Steel Ball, 5/16" dia.  
Set Screw, 3/8-16 x 3/8"  
Spring  
Thrust Bearing  
Screw, 1/4-20 x 1-1/4" (6)  
Retaining Ring  
Retaining Ring  
Washer (6)  
Washer (5)  
"O" Ring  
Square Cut Ring  
Threaded Plug (Shipping only, not used)  
Roller Chain (No. 41 chain, 24 links)  
Sprocket (9 teeth)  
Sprocket (18 teeth)  
Grease (32 oz. bottle Bentonite grease)  
Gasket Eliminator (Loctite #515)  
Coupling (See page 26-27 for part number)  
Connector Shaft (See page 26-27 for part number)  
150 510334  
178  
179  
*
*
Flanged Bushing  
Spur Gear (37 teeth)  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 8  
WIRE HARNESSES  
BLADE  
CLUTCH  
ENGINE DECK  
WIRE HARNESS  
PART NO. 483075  
NEUTRAL  
INTERLOCK  
GROUND  
KOHLER  
(15 HP)  
WHITE  
BLACK W/RED STRIPE  
KAWASAKI  
(15 HP, 16 HP & 17 HP)  
BLACK  
BLACK  
E
F
A
B
C
D
BLUE  
WHITE  
G
H
WHITE  
YELLOW  
WIRE HARNESS  
ADAPTER - ENGINE  
INSTRUMENT  
SW08WH483075  
PANEL HARNESS  
HANDLE WIRE HARNESS  
PART NO. 482711  
MOWER  
ENGAGE  
SWITCH  
KEY  
SWITCH  
BLACK  
WHITE  
BLK W/RED STRIPE  
A
B
C
E
F
BLK W/RED STRIPE  
BLACK  
BLUE  
WHITE  
G
YELLOW  
TO  
D
H
OPERATOR  
PRESENCE  
SWITCH  
TO ENGINE  
DECK WIRE  
HARNESS  
POS  
HOURMETER  
NEG  
HOURMETER  
SW2007WH482711  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 8  
WIRE HARNESSES  
WIRE HARNESS ADAPTER  
PART NO. 481717  
KAWASAKI  
(15 HP, 16 HP & 17 HP)  
SW2006WH481717  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R
Section 8  
REPLACEMENT DECALS AND INFORMATION PLATES  
WARNING  
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING  
KIT, OR ENTIRE GRASS CATCHER INSTALLED  
483405  
2
1
WARNING  
ROTATING BLADES AND BELTS  
* Keep hands, feet & clothing clear  
* Keep all guards in place  
* Shut off engine & disengage blade  
clutch before servicing  
* Use caution in directing discharge  
* Read instruction manual before operating  
SPINNING BLADES  
KEEP CLEAR  
BLADE CONTACT & THROWN  
OBJECTS CAN INJURE  
483407  
DO NOT OPERATE UNLESS GRASS  
CATCHER, MULCHING KIT OR  
DISCHARGE CHUTE IS INSTALLED  
3
483406  
4
MANUFACTURED UNDER ONE OR MORE  
OF THE FOLLOWING PATENTS:  
S L O W  
4,487,006  
4,991,382  
5,133,176  
6,192,666  
7,065,946  
4,885,903  
4,998,948  
5,826,416  
6,766,633  
7,197,863  
4,920,733  
5,042,239  
5,832,708  
6,892,519  
7,237,374  
4,967,543  
5,117,617  
5,865,018  
6,996,962  
7,373,768  
F A S T  
R
C H O K E  
PATENTS PENDING  
481122  
5
6
WARNING  
BEFORE OPERATING  
Read operator's manual  
Solicite etiquetas en espanol  
a un distribuidor Scag  
Make sure guards, shields  
& safety devices are in  
place & working  
Clear area of children,  
bystanders & debris  
Mow across face of slopes  
Trained operators only  
483441  
48404  
7
8
WARNING  
MOUNT RIDING  
ATTACHMENT  
HERE  
FALLING HAzARD  
USE ONLY SCAG APPROvED  
RIDING ATTACHMENTS  
WARNING  
483404  
SEE OPERATOR'S MANUAL  
INSTALL BELT COvER  
9
BEFORE OPERATING MACHINE  
READ OPERATOR'S MANUAL  
483402  
10  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
R
Section 8  
REPLACEMENT DECALS AND INFORMATION PLATES  
Ref.  
No.  
Part No.  
Description  
1
2
483405  
48314  
Decal, Discharge Chute  
Decal, Scag Logo  
3
4
5
6
7
8
483407  
483406  
483044  
481122  
483441  
48404  
Decal, Danger-Spinning Blades  
Decal, Warning-Rotating Blades  
Decal, Patents  
Decal, Instrument Panel - Front (SW36A-15KH, SW48V-15KH, SW52V-18KH)  
Decal, Instrument Panel - Rear  
Decal, Metalcraft - Made in USA  
9
483404  
483402  
481483  
482816  
48315  
Decal, Sulky Attachment  
Decal, Belt Cover  
Decal, Instrument Panel - Front (SW32-15KAI, SW36A-16KAI, SW48V-16KAI, SW52V-17KAI)  
Decal, Height of Cut  
10  
11  
12  
13  
Decal, 32  
482297  
483199  
483200  
481971  
48332  
Decal, 36 Advantage  
14  
Decal, 48 Velocity Plus  
Decal, 52 Velocity Plus  
Decal, Heavy Duty Commercial  
Decal, Shift Index  
15  
16  
**  
461986  
Spanish Decal Kit, Walk-Behinds (Not Shown)  
482816  
CUTTING HEIGHT ADJUSTMENT  
DECK MOUNTING HOLE POSITION  
R
NUMBER OF CASTER SPACERS (BELOW SUPPORT)  
FAST  
NUMBER OF SPACERS ABOVE CUTTER BLADES  
0
1
2
3
4
5
1-7/8  
2-1/8  
2-1/4  
2-7/8  
3-1/4  
3-3/8  
-
2-1/8  
2-3/8  
2-1/2  
-
3-1/2  
3-5/8  
1-5/8  
1-7/8  
2
2-5/8  
3
3-1/8  
TOP  
0
0
1
2
3
4
-
2-3/8  
2-5/8  
2-3/4  
-
-
MIDDLE  
MIDDLE  
BOTTOM  
BOTTOM  
BOTTOM  
-
SLOW  
-
-
-
4
-
481483  
-
3-3/4  
4-3/8  
4-1/8 3-7/8  
11  
12  
482297  
13  
14  
Hea Duty  
vy-  
Comm rc  
ial  
e
481971  
15  
16  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY - COMMERCIAL EqUIPMENT  
Any part of the Scag commercial mower manufactured by Scag Power Equipment and found, in the reasonable judgment  
of Scag, to be defective in materials or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer  
without charge for parts and labor during the periods specified below. This warranty is limited to the original purchaser and  
is not transferable. Proof of purchase will be required by the dealer to substantiate any warranty claims. All warranty work  
must be performed by an Authorized Scag Service Dealer.  
This warranty is limited to the following specified periods from the date of the original retail purchase for defects in  
materials or workmanship:  
•
•
•
•
Wear items including drive belts, blades, hydraulic hoses and tires are warranted for ninety (90) days.  
Batteries are covered for ninety (90) days.  
Frame and structural components including oil reservoir and oil coolers are warranted for 2 years (Parts and labor).  
Cutter decks are warranted against cracking for a period of three (3) years. (Parts and labor 1st and 2nd year; Parts  
only 3rd year.) The repair or replacement of the cutter deck will be at the option of Scag Power Equipment. We reserve  
the right to request components for evaluation. This warranty does not cover any mower that has been subject to mis-  
use, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as  
specified in the Operator’s Manual.  
•
•
Engines and electric starters are covered by the engine manufacturer’s warranty period.  
Major drive system components are warranted for two (2) years by Scag Power Equipment. (Parts and labor) (Two  
year warranty exclude fittings, hoses, drive belts). The repair or replacement of the hydraulic pump or hydraulic mo-  
tor will be at the option of Scag Power Equipment. This warranty does not cover any mower that has been subject to  
misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as  
specified in the Operator’s Manual.  
•
•
•
Electric clutches have a Limited Warranty for 2 year (Parts and labor).  
Spindle assemblies have a Limited Warranty for three years (Parts and labor 1st year and 2nd; Parts only 3rd year).  
Any Scag product used for rental purposes is covered by a 90 day warranty.  
The Scag mower, including any defective part must be returned to an Authorized Scag Service Dealer within the warranty  
period. The expense of delivering the mower to the dealer for warranty work and the expense of returning it to the owner  
after repair will be paid for by the owner. Scag’s responsibility is limited to making the required repairs and no claim of  
breach of warranty shall be cause for cancellation or rescission of the contract of sale of any Scag mower.  
This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or  
that has been operated in any way contrary to the operating instructions as specified in the Operator’s Manual.  
The warranty does not apply to any damage to the mower that is the result of improper maintenance, or to any mower  
or parts that have not been assembled or installed as specified in the Operator’s Manual and Assembly Manual. The  
warranty does not cover any mower that has been altered or modified, changing performance or durability. In addition, the  
warranty does not extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the  
reasonable judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance  
or durability.  
Scag Power Equipment reserves the right to change or improve the design of any mower without assuming  
any obligation to modify any mower previously manufactured. All other implied warranties are limited in duration to  
the two (2) year warranty period or ninety (90) days for mowers used for rental purpose. Accordingly, any such implied  
warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety after  
the expiration of the appropriate two year or ninety day warranty period. Scag’s obligation under this warranty is strictly  
and exclusively limited to the repair or replacement of defective parts and Scag does not assume or authorize anyone to  
assume for them any other obligation. Some states do not allow limitations on how long an implied warranty lasts, so the  
above limitation may not apply to you.  
Scag assumes no responsibility for incidental, consequential or other damages including, but not limited to, expense  
for gasoline, expense of delivering the mower to an Authorized Scag Service Dealer and expense of returning it to the  
owner, mechanic’s travel time, telephone or telegram charges, rental of a like product during the time warranty repairs are  
being performed, travel, loss or damage to personal property, loss of revenue, loss of use of the mower, loss of time or  
inconvenience. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above  
limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other  
rights which vary from state to state.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
GARANTÍA LIMITADA - EQUIPO COMERCIAL  
Toda pieza del cortacésped comercial Scag fabricada por Scag Power Equipment que, según criterio razonable de Scag, presente  
materiales o mano de obra defectuosos será reparada o reemplazada por un distribuidor autorizado Scag sin cargo por las piezas ni mano  
de obra durante los períodos especificados abajo. Esta garantía se limita al comprador original y no es transferible. Para acceder a  
cualquier reclamo de garantía, el distribuidor requerirá el comprobante de compra. Todo trabajo bajo garantía debe realizarlo un distribuidor  
autorizado Scag.  
Con respecto a materiales o mano de obra defectuosos, esta garantía se limita a los siguientes períodos especificados a partir de la fecha  
de compra original:  
* Los artículos desgastables, incluyendo correas de transmisión, cuchillas, mangueras hidráulicas y llantas, están garantizados  
por noventa (90) días.  
* Las baterías están garantizadas por noventa (90) días.  
* El bastidor y los componentes estructurales, incluyendo el depósito de aceite y los enfriadores de aceite, tienen una garantía de  
2 años (Piezas y mano de obra).  
* Las plataformas de corte están garantizadas contra grietas por un período de tres (3) años. (Piezas y mano de obra, primer y  
segundo año; piezas solamente, tercer año). La reparación o el reemplazo de la plataforma de corte estarán sujetos a discreción  
de Scag Power Equipment. Nos reservamos el derecho de solicitar componentes para su evaluación. Esta garantía no cubre  
ningún cortacésped que haya sido sometido a uso indebido, descuido, negligencia o accidente, o que se haya operado de manera  
distinta a la especificada en el manual del operador.  
* Los motores eléctricos y los arrancadores están cubiertos por el período de garantía del fabricante de motor.  
* Los componentes principales del sistema de transmisión están garantizados por Scag Power Equipment por dos (2) años.  
(Piezas y mano de obra) (La garantía de dos años no incluye las conexiones, mangueras, las correas de transmisión). La  
reparación o el reemplazo de la bomba hidráulica o el motor hidráulico estarán sujetos a discreción de Scag Power Equipment.  
Esta garantía no cubre ningún cortacésped que haya sido sometido a uso indebido, descuido, negligencia o accidente, o que se  
haya operado de manera distinta a la especificada en el manual del operador.  
* Los embragues eléctricos tienen una Garantía limitada de 2 años (Piezas y mano de obra).  
* Los ensambles del eje tienen una Garantía limitada de 3 años (Piezas y mano de obra, primer y segundo año; piezas  
solamente, tercer año).  
* Cualquier producto Scag que se utilice para alquiler está cubierto por una garantía de 90 días.  
El cortacésped Scag, incluida cualquier pieza defectuosa, debe ser llevado a un distribuidor autorizado de Scag dentro del período de  
garantía. Los gastos incurridos en la entrega del cortacésped al distribuidor para que se realice el trabajo bajo garantía, así como los  
gastos de devolución del cortacésped al propietario después de la reparación, estarán a cargo del propietario. La responsabilidad de Scag  
se limita a la realización de las reparaciones requeridas y ninguna reclamación por incumplimiento de las obligaciones de garantía será  
causa de cancelación o revocación del contrato de venta del cortacésped Scag.  
Esta garantía no cubre ningún cortacésped que haya sido sometido a uso indebido, descuido, negligencia o accidente, o que  
se haya operado de manera distinta a la especificada en el manual del operador. La garantía no será de aplicación en ningún caso  
de daño ocasionado al cortacésped como consecuencia de mantenimiento inadecuado o a cualquier cortacésped o piezas que no se hayan  
ensamblado o instalado de acuerdo con las especificaciones del manual del operador o el manual de montaje. La garantía no cubre ningún  
cortacésped que haya sufrido alteraciones o modificaciones que hayan afectado su funcionamiento o durabilidad.Asimismo, la garantía no  
se extiende a reparaciones necesarias por el desgaste normal o por el uso de piezas o accesorios que, según criterio razonable de Scag,  
sean incompatibles con el cortacésped Scag o afecten la operación, funcionamiento o durabilidad de éste.  
Scag Power Equipment se reserva el derecho de modificar o mejorar el diseño de cualquier cortacésped sin tener por ello  
obligación alguna de modificar cualquier cortacésped fabricado con anterioridad. Cualquier otra garantía implícita se limita a un  
período de garantía de dos (2) años o noventa (90) días en el caso de cortacéspedes destinados a alquiler. Por consiguiente, se rechaza en  
su totalidad cualquier garantía implícita, incluidas las garantías de comerciabilidad, adecuación para un fin determinado, o de otro tipo,  
después de la finalización del correspondiente período de garantía de dos años o noventa días. La obligación de Scag en virtud de la  
presente garantía se limita estricta y exclusivamente a la reparación o el reemplazo de piezas defectuosas, y Scag no asume ni autoriza a  
ningún otro a asumir en su lugar ninguna otra obligación. La limitación antes mencionada no será de aplicación en aquellos estados en los  
que no esté permitida la limitación del período de validez de una garantía implícita.  
Scag no asume responsabilidad alguna por daños incidentales, consecuentes ni de cualquier otro tipo, incluyendo, pero sin limitarse a, gasto  
de gasolina, gasto de entrega del cortacésped a un distribuidor autorizado Scag y gasto de su devolución al propietario, tiempo de viaje del  
mecánico, cargos por comunicaciones telefónicas o telegramas, alquiler de un producto similar durante el período en que se llevan a cabo  
las reparaciones bajo garantía, viajes, pérdida o daño de bienes personales, lucro cesante, daños ocasionados por la pérdida del uso  
del cortacésped, daños por la pérdida de tiempo o cualquier otro inconveniente. La limitación o exclusión antes  
mencionada no será de aplicación en aquellos estados en los que no esté permitida la exclusión o limitación de daños  
incidentales o consecuentes. La presente garantía le otorga derechos legales específicos, aparte de los derechos de los  
que usted goza, según el estado.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2 1  
C e r o  
l b s . 5 7 5  
C e r o  
l b s . 5 5 5  
C e r o  
l b s . 5 1 0  
C e r o  
l b s . 4 9 0  
R a d i o d e g i r o  
P e s o c o n r e c  
5 3 5 l b s .  
5 1 5 l b s .  
4 7 0 l b s .  
4 5 0 l b s .  
P e s o  
4 0 . 5 "  
4 0 . 5 "  
7 1 . 0 "  
5 3 . 0 "  
6 4 . 5 "  
3 7 . 0 "  
7 6 . 0 "  
7 6 . 0 "  
4 0 . 5 "  
4 0 . 5 "  
6 8 . 0 "  
4 9 . 0 "  
6 0 . 5 "  
3 7 . 0 "  
7 6 . 0 "  
7 6 . 0 "  
4 0 . 5 "  
4 0 . 5 "  
5 6 . 0 "  
3 7 . 0 "  
4 0 . 5 "  
4 0 . 5 "  
5 1 . 0 "  
3 3 . 0 "  
4 3 . 0 "  
3 2 . 0 "  
7 0 . 0 "  
7 0 . 0 "  
A l t u r a c o n r e  
A l t u r a :  
A n c h o c o n r e  
A n c h o ( c o n l  
A n c h o :  
A n c h o d e a l i n  
L o n g i t u d c o n  
L o n g i t u d :  
7 . 4 0 "  
3 7 . 0 "  
7 2 . 0 "  
7 2 . 0 "  
S W - 5 2 V  
S W - 4 8 V 3 6 A S W - 3 2 S W -  
A P R O X I M A D A S D I M E N S I O  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2 0  
E s p e c i f i c a  
F e c h a d e  
f o r m a s e g u r a y p r á c t i c a u n a b P e e b r i d m a i . t e a l o p e r a d o r l l e v a r e n  
S u j e t a v a  
e l i m i n a d o r a s y u n a p l a c a d e c i e r r e d e d e s c a r g a l a t e r a l .  
c o n d e f l e c t o r e s e n V e m p e r n a d o s , d i r e c t o r e s d e f l u j o , c u c h i l l a s  
p l a c a s t i p o “ o j o d e l a t o r m e n t a ” ( e y e o f t h e h u r r i c a n e ) c o m b i n a d  
E l e x c l u s i v o s i s t e m a m e z c l a H d u o r r d i p c e a j n p d a e a e : j a H u r r i c a m n e e z e c l m a d p E o l q e r u a i p l a o s  
c o r t e y l a d i s t r i b u c i ó n d e l a d e s c a r g a .  
g a d e a l t a v e l o c i d a d D . M e f e l e j o c t r o a r l a d e c a d l e i d s a c d a r d e l  
t u r b o  
D e f l e c t o  
y d e s c a r g a p o r t i r ó n d e u n a c u e r d a o t i p o r e c o g e r y d e s c a r g a r  
R e c o g e d o r d e c é s p e d G C - 4 D m c e d o t a e n l : c a p a c c é i d s d a p e d e d e 4 p i e s R c e ú c b o i c g o e s d  
R e c o g e d o r d e c é s p e d G C - F 4 t e c l a o d : n e c a p a c é i d s a d p e d e d e 4 p i e s R c e ú c b o i c g o e s d  
A R T Í C  
E S P E C  
K e v d l e a r B ,  
S e c c i ó n  
C o r r e a s  
B r a z o d e p o l e a p a r a s e r v i c i o p e s a d o d e c a n a l d e a c e r o B r d a e z o 1 / d 4 e "  
R o d a m i e n t o s O D d e 1 - 3 / 8 "  
P o l e a d e 5 " d e d i á m e t r o , d e f a b r i c a c i ó n s o l d a d a g y u r í e a m : P a c o h l e a a d a ,  
A c e r o p a r t i d o c o n c u b o s c ó n i c o s d e f á c i l d e e s j e m : d o e n l t a j e P o l e a s  
c a b e z a l m ó v i l d e a l i v i o d e e x c e s o d e g r a s a  
m a n t e n i m i e n t o c o n c o n e x i ó n d e g r a s a e n l a p a r t e s u p e r i o r y  
C u e r p o f u n d i d o , r o d a m i e n t o d e r o d i l l o s c ó n i c o s , b a j o E j e s :  
s u a v e , r o d a m i e n t o s d e r o d i l l o s y r e t i r o r á p i d o d e l p i n  
L l a n t a s m a c i z a s d e 9 x 3 . 5 c o n f l o t a c i ó n d e l a l b o a c a n s d : a d R e u r o e d a d s u  
p o r r e s o r t e  
A b e r t u r a d e d e s c a r g a e x t r a a n c h a c o n t o l v d a e d s d e c e a d r e g s a c : a r A g a b e c r a t r u g r a  
E m b r a g u e e l é c t r i c o d e f r e n o d e c c u u c c l h h a i i s l l l a d a s e c : o n i n t e r r u p t o A r d c e c i p o a n n a e m  
S W M 5 2 : T r e s ( 3 ) 1 8 "  
S W M 3 6 : D o s ( 2 ) 1 8 " ; S W M 4 8 : T r e s ( 3 ) 1 6 . 5 "  
M a r b a i n , . 1 9 7 d e g r o s o r  
c o r d t e e :  
C u c h i l l a s  
A j u s t a b l e d e s d e 1 - 3 / 4 " a 4 - 1 / 4 " e n c i n o c r d t r e e m e n a t o l t s u d r d e a e 1 / 4 A " j u s t e  
5 2 . 0 " ( 1 3 2 . 0 c m )  
3 2 . 0 " ( 8 1 . 3 c m ) , 3 5 . 5 " ( 9 0 . 2 c m ) , 4 8 . 0 " ( 1 2 2 c . 0 o r c d t m e e : ) , A n c h o  
S W M 5 2 V : A c e r o c a l i b r e 1 0 c o n f a l d ó n c a l i b r e 7 ( 3 / 1 6 " )  
S W M 3 2 , 3 6 A y 4 8 V : A c e r o c a l i b r e 7 c o n f a l d ó n d e c a l i C b o r e n s 7 t r ( u 3 c /  
D i s e ñ o d e l a n t e r o c o n r o d i l l o s a m o r t i g u a d o r e s d e l c : o o r p t i e T r a s a n t e  
V e l o c i t y P l u s S W M 5 2 .  
S W M 3 2 , S W M 3 6 A d v a n t a g e , S W M 4 8 V e l o c i t y P l u P s , L A T A  
C A I Ó N )  
( C O N T I N U  
C I O N E S T É C E N S I C P E A C S I F I C A  
S e c c i  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 9  
E s p e c i f i c a c i o n e  
F e c h a d e p u b l i c  
d i á m e t 1 r - o 1 . / 4 "  
B a r r a s d e l m  
n e u m á t i c a , d o s c a p a s . 1 3 . 0 x 6 . 5 0 - 6 s i n c á m a r a m o t r i c e s R / L u l a e n d t a a s s :  
P o l i e t i l e n o s i n c o s t u r a c s o , m d 6 e b g u a s l o t i b n l e e T s : a ( n 1 q 9 u . 0 e l i t r o s  
A c e r o c a l i b r e 7 .  
E s p e s o r :  
P L A T A F O  
V a r i a d o - C o n s u l t e l a e s v p á e l v d c u e i f l a i c : a c G i ó r n u d p e o l f a b r i c  
V a r i a d o - a C c o e d n i t e s e u : l t e l a b o e m s d p e b e a c i f i c a c C i ó o n n d j u e n l t f o a b r i c  
V a r i a d o - C o n s u l t e l a e s p e c i f i c c a o c m d i ó e b n u d s t e i b l f l a e b : r i c  
C o n j u n t o d e b  
e l e c t r ó n i c o E c o n n c e a n r r d a i d n o c a d o r d e r e t r o c e s o .  
A r r a n c a d o r / S  
S i l e n c i a d o r d e t u b o d e e s c a p e s i m E s p c l e a p y e d : o b l e  
E l e m e n t o d o b l e d e g r a n a c i a r e p d : a e c i d a F d i l t c r o o n f i l t r o d  
1 5 H P = K 3 o 6 h 0 l 0 e r r p m ( + / - 5 0 r p m ) , m a r c h a e n v a c í o p u e s  
( + / - 1 5 0 R P M )  
K a w a s a k i 1 5 0 1 7 H P = 3 6 0 0 r p m ( + / - 1 0 0 r p m  
K a w a s a k i 1 5 0 1 6 H P = 3 6 0 0 r p m ( + / - 1 0 0 r p m  
1 5 H P = 3 6 K 0 0 a w r p a m s a ( + k i / - 1 0 0 r p m ) , m a r c h a e n v a c í o p u e s t  
C o n t r o l a d o r t i p o m e c á n i c o c o n c o C n o t n r o t r l o d l a e d v o e r : l o  
K o h l e r C V 1 5 T = 4 2 6 c c  
K a w a s a k i F H 4 3 0 V = 4 3 1 c c : F H 4 D 8 0 e s V p = l a 4 z a 7 m 2 c i e c  
m o t o r d e e j e v e r t i c a l .  
K o h l e r 1 5 H P , m o t o r d e g a s o l i n a d e 4 c i c l o s ,  
a i r e , d o s c i l i n d r o s e n V , m o t o r d e e j e v e r t i c a l .  
K a w a s a k i 1 5 H P , 1 6 H P y 1 7 : o H p i P T m o t o r d e g a  
K o h l e r C V 1 5 T = 1 5 H P  
F H 4 3 0 V = 1 K 5 a H w P a , s F a H k 4 i 8 0 V = 1 6 H P , F H 5 4 1 V = 1 P 7 o H t e P n c i a :  
K o h l e r C V 1 5 T  
K a w a s a k i F H 4 3 0 V , F H 4 M 8 / 0 o V d e & l o F : M H 5 a 4 r c 1 a V  
I n d u s t r i a l d e s e r v i c i o p e s a d o / C o m T e i p r o c i g a e l n e r a l :  
M O T O R  
S W 4 8 V - 1 6 K A I , S W 5 2 V - 1 7 K A I  
S W 3 2 - 1 5 K A I , S W 3 6 A - 1 5 K H , S W M 3 O 6 D A E - 1 L 6 O K S A I  
C I O N E S T É C E N S I C P A E S C I F I C A  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 8  
S G B 0 2 5  
p l a t a f o r m a d e c o r  
A n c h o d e l a  
a u t o r i z a d o  
C o n s u l t e  
S C A G  
d i s t s r u i b u i c d o o n r  
A l o j a m i e n t o d e l a p l a t a f o r m a d o b l a d o  
t r a y e c t o r  
t r a v é s d e  
C r e s t a s i n  
S c a g a u t o r i z a d o  
C o n s u l t e c o n s u d i s t r i b u i d o r  
F a l l a d e l e j e i n t e r n o  
a u t o r i z a d o  
C o n s u l t e c o n s u d i s t r i b u i d o r S C A G  
C o r t e i n c  
Á r e a d e m o n t a j e d e l e j e d o b l a d a  
S G B 0 2 4  
p l a t a f o r m a d e c o r t  
A n c h o d e l a  
S c a g a u t o r i z a d o  
C o n s u l t e c o n s u d i s t r i b u i d o r  
M
a u t o r i z a d o  
C o n s u l t e  
S C A G  
d i s t s r u i b u i c d o o n r  
F a
C u c h i l l a d o b l a d a  
R e e m p l a c e l a c u c h i l l a  
t r a y e c t o r i a  
e n e l c e n t r  
C o r t e l a t e  
A j u s t e l a i n c l i n a c i ó n y e l n i v e l  
C u c h i l l a s m a l m o n t a d a s , d i s p a r e j a s  
S G B 0 2 2  
s e q u e  
p l a t a f o r m a d e c o r t  
A n c h o d e l a  
C é
C o r t e e l c é s p e d u n a v e z q u e s e  
a l a s c o n d i c i o n e s d e l t e r r e n o  
D i s m i n u y a l a v e l o c i d a d p a r a a j u s t a r s e  
V e
d e l c o r t e  
p l a t a f o r m a d e c o r t e y / o c a m b i a r l a d i r e c c i ó n  
e l t e r r e n o , a u m e n t a r l a a l t u r a d e l a  
S e p u e d e t e n e r q u e r e d u c i r l a v e l o c i d a d e n  
T e
c o r t e y / o c a m b i a r l a i n c l i n a c i ó n y e l n i v e l  
p l a t a f o r m a d e c o r t e , c a m b i a r l a d i r e c c i ó n d e l  
e l t e r r e n o , a u m e n t a r l a a l t u r a d e l a  
C o r t e d e m a s i a d o b a j o  
S e p u e d e t e n e r q u e r e d u c i r l a v e l o c i d a d e n  
m u y c e r c a  
t i e r r a o e s  
V e l o c i d a d d e m a s i a d o a l t a c u c h i l l a s  
a l a s c o n d i c i o n e s d e l t e r r e n o  
D i s m i n u y a l a v e l o c i d a d p a r a a j u s t a r s e  
R a s p a d o r  
B a j a p r e s i ó n d e l a s l l a n t a s  
V e r i f i q u e y a j u s t e l a s p r e s i o n e s  
C O N D I C I Ó N  
S O L U C I Ó N  
C A U S A  
I d e n t i f i c a c i ó n d e f a  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 7  
S G B 0 2 3  
p l a t a f o r m a d e c o r t e  
A n c h o d e l a  
i n c
a u t o r i z a d o  
P l a
C o n s u l t e c o n s u d i s t r i b u i d o r S C A G  
l l a n t a s  
R u e d a s d i s p a r e j a s  
d e c o r t e  
R e v i s e y a j u s t e l a p r e s i ó n d e l a s  
a n c h o d e l a  
S a l i e n t e s i n c  
p r e s i ó n d e l a s l l a n t a s  
R e v i s e y a j u s t e l a  
S G B 0 2 1  
l l a n t a s  
R e v i s e y a j u s t e l a p r e s i ó n d e l a s  
p l a t a f o r m a d e c o r t e  
A n c h o d e l a  
o p e r f i l i r r e g  
o n d u l a d a , c o  
A p a r i e n c i a b  
t e r r e n o d i s p a  
C o r t e d i s p a r  
c a m b i a r l a d i r e c c i ó n d e l c o r t e  
a l t u r a d e l a p l a t a f o r m a d e c o r t e y / o  
v e l o c i d a d e n e l t e r r e n o , a u m e n t a r l a  
S e p u e d e t e n e r q u e r e d u c i r l a  
T e r r e n o d i s p a r e j o  
S G B 0 2 0  
p l a t a f o r m a d e c o r t e  
A n c h o d e l a  
A f i l e l a c u c h i l l a  
d e s a f i l a d C a u
a u t o r i z a d o  
C o n s u l t e c o n s u d i s t r i b u i d o r S C A G  
Á
i n
S c a g a u t o r i z a d o  
C o n s u l t e c o n s u d i s t r i b u i d o r  
P l
( i n d e  
D e m a s i a d o á n g u l o e n l a c u c h i l l a  
p l a t a f o r m a d e c o r t e  
A j u s t e l a i n c l i n a c i ó n y e l n i v e l  
p l a t a f o r m a  
L i m p i e l a p a r t e d e a b a j o d e l a  
C é s p e d a c u m u l a d o d e b a j o d e l a  
o p e r f i l i r r e g  
o n d u l a d a , c o  
A p a r i e n c i a b  
t e r r e n o p l a n o  
h a c i a e l t e r r e n o  
M o n t e l a c u c h i l l a c o n e l f i l o  
C u c h i l l a m o n t a d a i n v e r t i d a  
R e e m p l a c e l a c u c h i l l a  
L e v a n t a d o r d e l a c u c h i l l a d e s C g o a r s t e t a d d o i s p a r  
C O N D I C I Ó N  
S O L U C I Ó N  
C A U S A  
I d e n t i f i c a c i ó n d e f a l l a  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 6  
S G B 0 1 9  
d e c o r t e  
d e c o r t e  
p l a t a f o r m a  
A n c h o d e l a  
p l a t a f o r m a  
A n c h o d e l a  
t r a y e c t o r  
c é s p e d s  
A u m e n t e e l t r a s l a p e d e c a d a p a s e  
R e e m p l a c e l a s c u c h i l l a s  
T r a s l a p e i n s u f i c i e n t e e n t r e e p t V a a s s a - d a F s r a n  
C S G B 0 1 8
p l a t a f o r m a d e c o r t e  
A n c h o d e l a  
C o r t e e l c é s p e d u n a v e z q u e s m e o s j e a q d u o e C
a l a s c o n d i c i o n e s d e l t e r r e n o  
V
D i s m i n u y a l a v e l o c i d a d p a r a a j u s t a r s e  
p
p l a t a f o r m a  
C d e l a  
L i m p i e l a p a r t e d e a b a j o d e l a  
A j u s t e l a t e n s i ó n d e l a c o r r e a  
C
O p e r e e l m o t d o e r l a 3 6 ( r 0 p 0 m R ) P M  
A f i l e l a s c u c h i l l a s  
r e v o l u c B i o a n j a e s s  
A f i l a d o i n c o r r e c t o d e l a s c u c h i l l a s  
d e c o r t e  
s i n c o r t a  
A f i l e l a s c u c h i l l a s  
V e t a s - F  
C u c h i l l a s d e s a f i l a d a s o d e s g a s t a d a s  
S G B 0 2 0  
C
p l a t a f o r m a d e c o r  
A n c h o d e l a  
A j u s t e l a t e n s i ó n d e l a c o r r e a  
p
p l a t a f o r m a  
C d e l a  
i n
C o  
L i m p i e l a p a r t e d e a b a j o d e l a  
A f i l e l a s c u c h i l l a s  
s e s e q u e  
C
C o r t e e l c é s p e d u n a v e z q u e  
a l a s c o n d i c i o n e s d e l t e r r e n o  
D i s m i n u y a l a v e l o c i d a d p a r a a j u s t a r s e  
V e l o c i d a d d e m a s i a d o a l t a  
s i n c o r t a r  
o c a s i o n a  
L a r g u e r o  
O p e r e e l m o t o r a 3 6 0 0 R P M  
B a j a s r e v o l u c i o n e s ( r p m ) d e l m o t o r  
C O N D I C I Ó N  
S O L U C I Ó N  
U S A C A  
I d e n t i f i c a c i ó n d e f a l l a s  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 5  
e x t r e m a s d e p o l v o o s u c i e d a d .  
* R e a l i c e c o n m á s  
m a n t e n i m i e n t o .  
i n f o r m a c i ó n s o b r e e s t e p r o c e d i m i e n t o d e  
C o n t a c t e  
o p e d r a e d l o r m a e n l u a l V e a  
c h a d s e i s G r a s a  
o b t e n p e a r r a S c a g  
m o t d o e r l ;  
d i s s t r u i b u c i o d n o r  
A j u s X t e e l e n t r e h i e r r o e n e l e m b r a g u e e l é  
R e e m X p l a c e e l f i l t r o d e c o m b u s t i b l e d e l m  
E n g X r a s e l o s e j e s d e l p i v o t e d e l a r u e d a l  
V e r i f i q u X e q u e t o d a l a t o r n i l l e r í a e s t é b i e  
E n g r a s e l o X s s o p o r t e s d e l a p o l e a d e l l a d o i z q u i e  
E n g r a s e X l o s a c o p l a m i e n t o s d e t r a n s m i s i  
E n g r a s e X l o s r o d a m i e n t o s d e l a r u e d a m o  
E n g r a s e X l o s r o d a m i e n t o s d e l a r u e d a l o c  
* R e e m p X l a c e e l e l e m e n t o d e l f i l t r o d e a i r e  
V e r i f i q u X e l a c o r r e c t a a l i n e a c i ó n d e t o d a  
C a m b i e X  
n e c e e s s s a i r i o  
f r e c u e n m c i a a y o C r o n  
G r a s a d e c h a s i s  
c h a d s e i s G r a s a  
c h a d s e i s G r a s a  
c h a d s e i s G r a s a  
m o t d o e r l  
m o t d o e r l  
o p e d r a e d l o r m a e n l u a l V e a  
V e a e l m a n u a l d e l o p e r a d o r d e l m o m t o o r t d o e r l a c e l i t e  
+ G r a s a b l a n c a d e l i t i o U S e j M e d P e 2 l 1 2 5 r o d a l o m s i e n t o s E n g r a s e  
o p e d r a e d l o r m a e n l u a l V e a  
V e a l a p á g i n a 1 3  
p á l g a i n a V e a  
X
C a m b i e e l a c e i t e X d e l m o t o r y e l f i l t r o  
c o e r t l a c é s p e d * L i m p i e  
X
1 1  
1 1 y 1 0  
A f i l e l a s c u c h i l l a s d e X c o r t e  
p á g l i a n s a s V e a  
p á l g a i n a V e a  
p á l g a i n a V e a  
V e r i f i q u e l a t e n s i ó n d X e l a c o r r e a  
R e v i s e l a p r e s i ó n d e X l a s l l a n t a s  
R e v i s e e l s i s t e m a d e X p r e s e n c i a d e l o p e r  
* L i m p i e e l e l e m e n t o X d e l f i l t r o d e a i r e  
V e r i f i q u e e l n i v e l d e X a c e i t e d e l m o t o r  
V e r i f i q u e l a c o r r e c t a a l i n X e a c i ó n d e t o d a  
V e r i f i q u e q u e t o d a l a t o r X n i l l e r í a e s t é b i e  
8
5
m o t d o e r l  
m o t d o e r l  
o p e d r a e d l o r m a e n l u a l V e a  
o p e d r a e d l o r m a e n l u a l V e a  
P R O C E D I M I E N T O  
O B S E R V A C I O N E S  
S u p e r L u b M E P # 2 ( e s t a c i o n e s d e s e r v i c i o C o n o c o )  
M o b i l u x # 2 ( e s t a c i o n e s d e s e r v i c i o M o b i l )  
S h e l l A l v a n i a ( e s t a c i o n e s d e s e r v i c i o S h e l l )  
R o n e x M P ( e s t a c i o n e s d e s e r v i c i o E x x o n )  
4 0  
2 0 H O R A S  
8 H O R A S ( D I A  
L i d o k E P # 2 ( e n c o n t r a d a G e r n a s a a l s m c a o c m e n p e a t s i i b n l e d s u : s t r i a l e s )  
+ E n g r a s e e l e j e h a s t a q u e l a g r a s a s a l g a p o r l a v á l v u l a  
U S O I N I C I A L  
L U B R I C A C I Ó N Y M A N T E N I M I E N T O  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 4  
d e l a p i n t u r a .  
c o n u n a c e r a a u t o m o t r i z p a r a u n a m á x i m a p r o t e c c i ó n  
d i s t r i b u i d o r a u t o r i z a d o S c a g . E n c e r e e l c o r t a c é s p e d  
p i n t u r a d e r e t o q u e S c a g ( N / P 4 8 5 2 1 ) d i s p o n i b l e e n s u  
R e p a 3 r . e l a s s u p e r f i c i e s d e m e t a l d a ñ a d a s c o n l a  
c o r t a c é s  
m a n u a l  
o c a d a d  
c a m b i e e  
a c e i t e d e  
D e s p u é s  
N o r 2 o . c í e l o s c o m p o n e n t e s e l é c t r i c o s .  
a u t o m o t r i c e s . N o u s e l i m p i a d o r e s a p r e s i ó n .  
p l a t a f o r m a d e c o r t e . U s e a g u a f r í a y l i m p i a d o r e s  
D e s p 1 u . é s q u e c a d a u s o , l a v e e l c o r t a c é s p e d y l a  
T E R  
C E I T E D E L C Á C R A M B I  
c o r t a c é s  
e l m a n u a  
c a d a 8 h o  
E l n i v e l  
c a l i e n t e . N o l a v e e l m o t o r ; u s e a i r e c o m p r i m i d o .  
N o l a v e n i n g u n a p a r t e d e l e q u i p o m i e n t r a s e s t á  
U C I Ó N : P R E C A  
C Á R T E  
C I Ó N D E L V N E I R V I E F L I  
C E I T E D E L  
L I M P I E Z A D E L A M Á Q U I N A  
p e r s o n a l i z a d o d e 4 "  
t e  
o s P i c i ó n d e l d F e i g f l u e r c a t o 1 r 2 d . e  
O P E D E T  
P L A N A  
A R A N D E L A  
.
e v e n i r d a ñ o s a l m o t o d r i a r i a m e n t e p a r a p r  
e
o d e a i r  
n e c e s a r i o d a r s e r v i c i o T U a E l R C f A i l E t r L Á S T I C A  
2 0 0 4 C C B 4 " S e t t i n g S P  
-
E n c o n d i c i o n e s d e m u c h o p o l v o , p u e d e s e r  
- A T - N O  
c o n e s t e c o r t a c é s p e d p a r a i n s t r u c c i o n e s .  
C o n s u l t e e l m a n u a l d e l o p e r a d o r d e l m o t o r p r o p o r c i o n a d o  
A J U S T E D  
A R A O S P G U J E D R E A  
d e t e r m i n O a l o s p e r í o d o s d e P s E e R r v N i O c i o D E d L e l C f A i R l t R r o d e a i r e .  
P a r a c u a l q u i e r f i l t r o d e a i r e , e l a m b i e n t e d e o p e r a c i ó n  
O I N F E R I O C R O N J U N T  
p e r s o n a l i z a d o d e 3 -  
o s P i c i ó n d e l d F e i g f l u e r c a t o 1 r 1 d . e  
O T R  
O D T E R F A I I L R E D E L M O  
t e  
O P E D E T  
P L A N A  
T U E R C A E L Á A S R T A I C N A D E L A  
m o t o r p a r a i n s t r u c c i o - n e s .  
2 0 0 4 C C B 3 - 1 / 2 " S e t t i n g S P  
q u e o c u r r a p r i m e r o . C o n s u l t e e l m a n u a l d e l o p e r a d o r d e l  
a c e i t e c a d a 1 0 0 h o r a s d e o p e r a c i ó n o c a d a d o s s e m a n a s , l o  
. L u e g o , r e e m p l a c e e l f i l t r o e d l e f i l t r o d e a c e i t e d e l m o t o r  
D e s p u é s d e l a s p r i m e r a s 2 0 h o r a s d e o p e r a c i ó n , r e e m p l a c e  
R O T M O  
C A M B I O D E F I L  
A J U S T E D E 3 ½  
A R A O E L S P G A U J E R  
O C E N T R A C L O D N E J U N T  
O
P E R N O D E L C A R R  
C E I T E D O E D L T E R A  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 3  
p e r s o n a l i z a d o d e 3 "  
t e  
o s P i c i ó n d e l d F e i g f l u e r c a t o 1 r 0 d . e c o r  
O P E D E T  
P L A N A  
T U E R C A E L Á S T I C A  
A R A N D E L A  
2 0 0 4 C C B  
-
3 " S e t t i n g S P  
r e d u c i r á l o s “ s o p  
4 " m e j o r a r á e l c o  
A
A R A O S P G U J E D  
O S U P E R I C  
F i g u r a 1 2 ) L a c o l  
s o l d a d o d e n t r o d e  
c o n j u n t o i n f e r i o r  
O
P E R N O D E L C A R R  
e a l a  
e l V o c i t y - c P o l r u t s e ) - e l d e f l e c t  
P o . s i C c i ó n 4 " ( a j u s  
t o r n i l l o s c o n u n t o r q u e d e 3 9 p i e s - l b .  
e a l a s F i g u r m a s u 1 e 0 s t r h a a . s ( t V a l a 1 2 ) .  
u e V l v a 3 a . i n s t a l a r l o s a c c e s o r i o s d e m o n t a j e c o m o s e  
A p r i e t e l o s  
d e d e s e m p e ñ o d e  
e n l a p o s i c i ó n 3 - 1  
g e n e r a l , c o l o q u e  
p a r a l a u b i c a c i ó n ) .  
e a l a s F i g u r a s 1 0 h a s p t a o s l a i c 1 i ó 2 n d e s e a d a . ( V  
1 ) . P a r a c o r t e s e a d e l a p F r o i g p c u ó o r s a r i t e 1 o . ( V  
d e f l e c t o r f r o n t a l  
i n s t a l a u s a n d o e l  
M u e 2 v . a e l d e f l e c t o r d e c o r t e p e r s o n a l i z a d o a l a  
A d v a n t a g e ) - e l d e f l e p c l t a o t r a f s o e r m a s d e c  
P o . s i B c i ó n 3 - 1 / 2 " (  
F i g u r a 9 . D e f l e c t o r d e c o r t e p e r s o n a l i z a d o  
2 0 0 4 C C B S P  
.
c é s p e d m u y a l t o ,  
A d v a n t a g e e n t r e  
F i g u r a 1 0 ) . L a s p  
s o l d a d o d e n t r o d  
c o n j u n t o s u p e r i o  
P o . s i A c i ó n 3 " - e l d  
e l V o c i t y - P l u s y  
e a l a  
A J E  
D E M O N T  
O T R N I L L E R Í A  
A J E  
D E M O N T  
O T R N I L L E R Í A  
d i f e r e n t e s p a  
E l d e f l e c t o r  
p l a t a f o r m a p  
p e r s o n a l i z a r  
p e r s o n a l i z a d  
s u p e r i o r e n c  
e n t r e g a r u n ó  
E l d e f l e c t o r  
d o c o n a c e u l e t r a m a ñ o d e l a p l a t a f o r m a d e c o r t e .  
u b i c a c i ó n d e l o s a c c e s o r i o s p u e d e v a r i a r d e  
i l u s t r a c i o n e s e s s ó l o p a r a r  
e n c i e a f . e r L a  
L a u b i c a c i ó n d e l o s a c c e s o r i o s u s a d o s e n l a s  
- A T - N O  
e a l a F i g u r a 9 ) .  
p e r s o n a l i z a d o a l a p l a t a f o r m a d e c o r t e ( V  
R e t . i r 1 e l o s a c c e s o r i o s q u e a s e g u r a n e l d e f l e c t o r d e c o r t e  
P E R S O N A  
A J U S T E D  
T E P E R S O N O A L R I Z D A E D C O O D R E F L E C T  
T U R A D E L A R L A A L A P R A A J U S T  
T E  
O R D E C O R  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 2  
F i g u r a 8 . A f i l a d o d e l a s c u c h i l l a s  
S G B 0 3 3 S P  
3 0  
d e l a n c h o d e l a c u c h i l l a  
X N O d e b e e x c e d e r 1 / 3  
X
h i l l a s .  
a , f i l a r e i n s t a l a r c u o c t e p c r c i ó n a l r  
p r o t e c t o r e  
N o c o r t e  
l a c u c h i l l a  
M a n t e n g a e l á n g u l o d e  
U s e p r o t e  
L a s c u c h i  
A D V E R T E N C I A :  
u s t e d m i s m o .  
e b a e l a f i n e c r e a r s u s c u c e h s i p l l e a c s i a l e s s i p r  
p a r a b a l a n c e a r l a c u c h i l l a o p o r h e r r a m i e n t a s  
C o n s u l t e c o n s u d i s t r i b u i d o r a u t o r i z a d o S c a g  
o d e l c e o m n a j u t u n r t o d e l e y j e d . e s g a s t e p r  
e a l a F i g u r y a e 7 l ) . e j e (  
i n s t a l a r s  
P a r a u n  
o d u c i r s e v i b r a c i ó n  
d e s b a l a n c e a d a s , p u e d e p r  
e l b a l a n c e d e l a c u c h i l l a . S i l a s c u c h i l l a s e s t á n  
e s m e r i l a d o r a , p u e d e q u e m a r l a c u c h i l l a .  
i g u a l .  
o T d a s l a s c u c h  
e v R i s e  
A f i l e l a c u c h i l l a c o n u n a l i m a . S i u s a u n a  
- A T - N O  
- A T - N O  
e a ( l V a F i g u r a 8 ) .  
s u p e r i o r  
N o a f i l e l a s c u c h i l l a s m á s d e 1 / 3 d e l a n c h o d e l a c u c h i l l a .  
4 " e n l o s  
c u a l q u i e  
E l a j u s t e  
C u c h i l l a s d e c o r t e  
F i g u r a 7 . E s p a c i a d o r e s d e c u c h i l l a  
T E  
T U R A D E C O R  
A J U S T  
F i g u r a 6 . E s  
2 0 0 3 S G B 0 0 5 S P  
E s p a c i a d o r e s  
P i n  
e a l a F i g u r a 6 ) .  
i n c l i n a c i  
r e u b i c a d  
L o s e s p a  
( C O N T  
A J U S T  
T E  
A T F O R M A D E C O R  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 1  
a , f i l a r e i n s t a l a r c u o c t h e p i c l r l c a i s ó . n a l r e t i r a r  
p r o t e c t o r e s o f o r r e l a s c u c h i l l a s c o n m a t e r i a l d e  
U s e p r o t e c c i ó n a p r o p i a d a p a r a l o s o j o s y g u a n t e s  
L a s c u c h i l l a s t i e n e n u n b o r d e d e c o r t e a f i l a d o .  
T E N C V E I A A R : D  
T E  
T U R A D E C O R  
A J U S T E F i D g E u r A a L 5 .  
S C 4 0 5 G - 0 6 S P  
A J U S T E D E A L T U R A  
e a l a F i g u r y a e 7 l ) . e j e ( V  
i n s t a l a r s e p o r l o m e n o s t r e s e s p a c i a d o r e s e n t r e l a c u c h i l l a  
P a r a u n m e j o r c o r t e y u n a m e j o r d e s c a r g a , d e b e n  
( 3 1 / 4 " a 4 1 / 2 " )  
i g u a l .  
C O R T E A L T O  
o T d a s l a s c u c h i l l a s d e b e n e s t a r d i s t r i b u i d a s p o r  
- A T - N O  
( 2 1 / 2 " a 3 3 / 4 " )  
s u p e r i o r d e l e j e o R p A o N r G d O e b M a E j o D I d O e l e j e .  
4 " e n l o s p e r n o s d e m o n t a j e d e l a c u c h i l l a a l a p a r t e  
c u a l q u i e r a d e l o s c i n c o e s p a c i a d o r e s m á s p e q u e ñ o s d e 1 /  
E l a j u s t e d e l a a l t u r a d e c o r t e p u e d e r e a l i z a r s e m o v i e n d o  
C O R T E B A J O ( 1 3 / 4 " a 3 " )  
T E  
T U R A D E C O R  
A J U S T E D E L A A L  
H a y t r e s p o s i  
a j u s t e t a m b i é  
m e d i a n t e l a r  
L o s c a m b i o s  
F i g u r a 6 . E s p a c i a d o r e s d e l a r u e d a l o c a  
2 0 0 3 S G B 0 0 5 S P  
l a a l t u r a d e c  
p u n t a d e c o r t  
A j u s t e d e  
a m b i é n c o n s u l t e  
a p u n t a n d o l a  
t e r r e n o . E s t a  
e s l a d T i s U t a A R n c L A i a n o m i n a  
( c o m p a r a n d o  
I N C L I N A C I  
E s p a c i a d o r e s  
P i n  
a l t u r a .  
q u e p u e d e n r  
f u n c i o n e p a r a  
d i f í c i l r e c o m  
D e b i d o a l a s  
e a l a F i g u r a 6 ) .  
i n c l i n a c i ó n d e l a p l a t a f o r m a . ( V  
r e u b i c a d o s p a r a m o d i f i c a r l a s a l t u r a s d e c o r t e y l a  
T E  
A T F O R M A D E C O R  
A J U S T E S  
L o s e s p a c i a d o r e s d e l a r u e d a l i b r e t a m b i é n p u e d e n s e r  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 0  
R e t i 4 r e . l a c u b i e r t a  
F i g u r a 3 . C  
D E L A C O R R E A D E L  
V E R I F I Q  
T E N S I U Ó Í Q N L A U E A  
S C 4 0 2 G S P  
D E S C A R G A  
Á R E A D E  
p o s i c i ó n n e u t r a l , l a m á q u i n a d e b e m o v e r s e l i b r e m e n t e .  
l a s p a l a n c a s d e d i r e c c i ó n e s t á n b l o q u e a d a s e n l a  
d i r e c c i ó n s e t i r e n f i r m e m e n t e h a c i a l a s a s a s . C u a n d o  
l o s f r e n o s n o s e a p l i q u e n h a s t a q u e l a s p a l a n c a s d e  
T E  
D E C O R  
L A C O R R E A  
A j u . s 2 t e l a s v a r i l l a s d e l f r e n o d e d i r e c c i ó n d e m o d o q u e  
A T F O R P M L A  
A J U S T E D E L A  
P O L E A D E  
D E  
D E T E N S I Ó N  
P O L E A D E A J U S T E  
d e s c o n e c t a d o .  
e q u i p o c o n e l s i s t e m a d e e n c l a v a m i e n t o  
p a r a m a y o r c l a r i d a d .  
c o r t e a m a n o d e r e c h  
F i g u r a 2  
e l e  
N u n c a o p e r  
e t i r a d a  
e s e n c i a d e l o p P e r a a l a d n o c r a r d e p r  
- A T - N O  
S C 4 0 1 G S P  
T U E R C A  
d i r e c c i ó n  
A R A N D E L A  
F i g u r a 4 . A j u s t e d e l a v a r i l l a d e c o n t r o l d e  
S C 4 0 4 G B 0 5 S P  
d e d i r e c c i ó n  
a l P a n c a d e l f r e n o  
C O R R E A  
3 / 4 "  
e a l a s F i g u r a s 2 y 3 ) .  
t u e r c a d e l p e  
A j u s t e l a p t r e e n s s i ó i ó n n . a p r e  
d e m o d o q u e  
o s P i c i ó n D R I V E  
l o q u d e e o b  
A j u s t e l a c o r r e a  
d e r e c h a c o n u  
A . j u 3 s t e l a c o  
o s P i c i ó n n e u t r a l  
d e o p e r a c i ó  
a j u s t e d e s p u  
e a p a t i n e , v e r i f i q u e e s t e p a r a e v i t a r  
D e b i d o a l e  
n e u t r a l  
S e g u r  
o
e a , y  
e a ( l V a F i g u r a 4 ) .  
- A T - N O  
r a n u r a d e l s e g u r o n e u t r a l e n l a p o s i c i ó n D R I V E .  
l a p l a t a f o r m a  
i n f e r i o r d e l a v a r i l l a h a s t a l a p a r t e i n f e r i o r d e l a  
q u e h a y a u n a l u z a p r o x i m a d a d e 3 / 4 " d e s d e l a p a r t e  
A j u s 1 t . e l a s v a r i l l a s d e c o n t r o l d e d i r e c c i ó n d e m o d o  
F i g u r a 1  
P O L E A D E A L I N E A C I Ó N - L  
P L A T A F O R M A D E C O R T E  
T E N S I Ó N D E L A C O R R  
T R I Z O L M O  
A J U S T E S D E C O N T R  
S C 4 0 0 G S P  
l a t e n s i ó n d e l a c o r r e a .  
d e s l i z a n d o l a p o l e a a l a i z q u i e r d a o d e r e c h a p a r a c a m b i a r  
a f l o j a n d o e l p e r n o d e m o n t a j e d e l a p o l e a g u í a y  
A R N D E L A  
A j u s t e  
d e 3 / 1 6 " d e d e s v i a c i ó n c o n 1 0 l b s . d e p r e s i ó n .  
A j u s t e l a c o r r e a d e t r a n s m i s i ó n d e m o d o q u e h a y a c e r c a  
T U E R C A  
E N L  
P E R N O " J "  
C O R R E A  
T R A N S M I S I Ó N C O R R E A D E L A  
E X T R E M O D E S O P O R  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
c o m p l e t a .  
m o t o r a 3 / 4 d e  
v i d a d e l e q u i p o  
e v e l o c i a d d a q d u . i P e r a r a a l c a  
e m b r a g u e e l é c t  
c a u s a d o p o r e  
d e s d e l a p a r t e  
d e s c o n e c t a d o , e  
C u a n d o e l P T O  
g a  
e a l a F i g u r a 1 ) .  
t u e r c a d e l p e r n o t i p o J . ( V  
A j u s t e l a t e n d s e i ó p n r e a s p i ó r n e t . a n d o o a f l o j a n d o l a  
d e m o d o q u e l a m i s m a s e m u e v a 1 / 2 " c o n 1 0 l i b r a s  
c o r t e c o n u n c a l i b r a d o r d e t e n s i ó n .  
A j u 2 s . t e l a c o r r e a d e t r a n s m i s i ó n d e l a p l a t a f o r m a d e  
c o r l r a e a A j u s t e  
- N O T A -  
R e t i 1 r e . l a c u b i e r t a d e l a c o r r e a .  
3 9 0 S 0 1 3 8  
a t r a b a j a r .  
P U S H D O W N T O D I S E N G A G E  
l a s p a r t e s m ó v i l e s s e d e t e n g a n a n t e s d e c o m e n z a r  
P U L L U P T O E N G A G E  
a n t e s d e r e a l i z a r c u a l q u i e r a j u s t e . E s p e r e q u e t o d a s  
D e t e n g a e l m o t o r y q u i t e l a l l a v e d e l e n c e n d i d o  
U C I Ó N : P R E C A  
T E  
A T F O R P M L A D E C O R  
d e s c o n e c t a r l a s c  
P r e s i o n e e l i n t e r r  
e m b r a g u e d e l a c  
p a l a n c a s d e o p e r  
A c c i 4 o . n e l a s c u c h  
A J U S T E S D E L A C O R R E A D E L A  
t r a n s m i s i ó n a n e u t r a l .  
b l o q u e e l o s s e g u r o s d e n e u t r a l y c a m b i e l a  
D E T A E P R N A E 8 R . S E , a p r i e t e a m b a s p a l a n c a s ,  
.
p u e d e n o s e r n e c e s  
o p e r a c i ó n d e a r r i b  
g i r a r a l a i z q u i e r d a , a p r i e t e l a p a l a n c a i z q u i e r d a . . S i e l m o t o r s e e s a t r h a o n g g a u , l r a e d p o i r t a l a  
u n g i r o a l a d e r e c h a , a p r i e t e l a p a l a n c a d e r e c h a . P a r a  
l a m á q u i n a s e d e s p l a z a r á e n l í n e a r e c t a . P a r a r e a l i z a r  
C u . a n 7 d o l a s p a l a n c a s d e l f r e n o d e d i r e c c i ó n s e l i b e r a n ,  
m o t o r a r r a n q u e , l e  
f r í o , t i r e d e l a p e r i l  
* E s t r a n g u l e s e g  
A r r a 3 n . q u e e l m o t o  
* E l i n t e r r u p t o r d  
l a p o s i c i ó n n e u t r a l .  
d i r e c c i ó n c o n a m b a s m a n o s , l i b e r e a m b o s s e g u r o s d e  
M i e n 6 t . r a s e s t á a p r e t a n d o l a s p a l a n c a s d e l f r e n o d e  
n e u t r a l d e b l o q u e o  
* L o s s e g u r o s d e  
t r a n s p o r t e !  
e c o m i e n d a ¡ S l a ó l o v e s l o e c r i d a d m á x i m a p a r a  
e s t a r l i b e r a d a s .  
- N O T A -  
* L a s p a l a n c a s d  
d e s e a d a .  
.
e s t a r e n l a p o s i c i ó  
* E l i n t e r r u p t o r d  
C a m 5 b . i e l a t r a n s m i s i ó n a l a v e l o c i d a d d e c o r t e  
m o v i m i e n t o h a c i a a d e l a n t e y r e v e r s a .  
* L a t r a n s m i s i ó n  
c a m b i o e n t r e e n g r a n a j e s o d e c a m b i a r e n t r e e l  
c o m p l e t a m e n t e d e t e n i d a a n t e s d e r e a l i z a r u n  
a l a t r a n s m i s i ó n , l a m á q u i n a d e b e e s t a r  
P a r a e v i t a r l e s i o n e s p e r s o n a l e s g r a v e s y d a ñ o s  
d a ñ a r á s e v e r a m e  
u s e c N o O m b u s t i b l e E 8 5 .  
y u n m á x i m o d e  
U s e g a s o l i n a c o  
A D V E R T E N C I A :  
- N O T A -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
d e l t a n q u e .  
A * b r a l a v á l v u l a d e c o m b u s t i b l e q u e e s t á a l f o n d o  
e n d e r e c e N n U i N s u C e l A d e c l u a s c h c i u l l c a h s i . l l a s  
e r V i f * i q u e e l n i v e l d e a c e i t e e n e l t a n q u e h i d r á u l i c o .  
s e r v i c i o a l a  
c u c h i l l a s o u  
T e . n 5 g 1 a c u i d a  
m á x i m o d e 1 0 % d e E t a n o l .  
y r e c i e n t e c o n u n o c t a n a j e m í n i m o d e 8 7 y h a s t a u n  
* L l e n e e l t a n q u e d e c o m b u s t i b l e c o n g a s o l i n a l i m p i a  
c o m p o n e n t e  
L i . b 4 e 1 r e c u i d a  
A n t e 2 s . d e a r r a n c a r e l m o t o r :  
d e t r a t a r d e o p e r a r e s t a m á q u i n a .  
L e a 1 y . e n t i e n d a l a s i n s t r u c c i o n e s d e s e g u r i d a d a n t e s  
c u a n d o s e a  
U . s e 3 1 s o p o r t e  
C A É T S P E D  
C I Ó N D O E P L E C R O A R  
a p r o b a d o p a  
S i . e 2 m 1 p r e a l m  
c o n e x i o n e s h a y a n s i d o l u b r i c a d a s .  
r e v i s i ó n p r e v e n t i v a p a r a a s e g u r a r s e d e q u e t o d a s l a s  
E l l u b r i c a n t e s e a p l i c ó e n f á b r i c a . E s t o s ó l o e s u n a  
A p . l i 6 q u e l u b r i c a n t e a t o d a s l a s c o n e x i o n e s .  
t r a n s p o r t e .  
C . o 1 r t 1 e e l c o m  
a l m a N c e O n e 1 0 l a . m á q  
.
O F F  
n e u t r a l y e l i n t e r r u p t o r d e a c c i o n a m i e n t o e s t á e n  
E l m o t * o r d e b e r á a r r a n c a r s i l a m á q u i n a e s t á e n  
P e r m 9 i . t a q u e  
N E U T R O .  
.
d e a c e i t e o d  
E l m 8 o . t o r d e b  
E * l m o t o r n o a r r a n c a r á s i l a m á q u i n a n o e s t á e n  
e n O N .  
a c e i t e o c o m  
p a r a p r e v e n i  
c o r t e , d e l a t r  
R e t i 7 r e . l a g r a  
E l m o t * o r n o a r r a n c a r á s i e l i n t e r r u p t o r P T O e s t á  
i n t e r r u p t o r e s d e s e g u r i d a d :  
e r V i f i q u 5 e . e l a j u s t e a d e c u a d o d e l o s  
t o d a s l a s c a l  
p a r a a s e g u r a  
f r e c u e n t e m e  
c o n d i c i o n e s  
t o r n i l l o s , p a r  
M a n 6 t e . n g a a p  
s e g ú n s e a n e c e s a r i o .  
R e v i 4 s . e q u e n o h a y a t o r n i l l e r í a f l o j a .  
A p r i e t e  
e r V i f i q u e  
P S I 1 2  
m a c i z a s L l a n t a s  
R u e d a s m o t r i c e s  
R u e d a s l o c a s  
e r V i f i q u 3 e . l a p r e s i ó n a d e c u a d a d e l a s l l a n t a s .  
.
c á r t e r  
1 ) .  
A j u s t e s , p á g i n a 1  
g a s o l i n a d e l  
m a n t e n i m i e n  
S i e l 5 c . o r t a c é  
c o n t r o l d e d i r e c c i ó n ( C o n s u l t e l a s e c c i ó n  
e r V i f i q u 2 e . e l a j u s t e n e u t r a l d e l a s v a r i l l a s d e  
n e c e s a r i o .  
r e a l i z a r c u a l q  
m á q u i n a . E s  
m o t o r c u a n d  
c a b l e s d e b u  
d e t e n g a e l m  
A j u s t e c o m o l o c o l n a s s i d 2 e , r 4 e y 8 h o r a s .  
e r V i f i q u 1 e . l a c o r r e c t a t e n s i ó n d e l a s c o r r e a s a  
A P R O X I M A D A M E N T E 1 0 H O R A S )  
( P R I M E R D Í A D E U S O O  
P R O C E D I M I E N T O S D E A R R A N Q U E I N I C I A L  
D e s c 4 o . n e c t e l  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
e s t é n a j u s t a d o s .  
l a s c u c h i l l a s e s t é  
d e o p e r a r l a p l a t  
R e p a r e c u a l q u i e r  
s i h a y d a ñ o s o p i  
v i b r a c i ó n e s u n a  
b u s q u e i n m e d i a t  
d e t e n g a e l m o t o r  
e l e q u i p o c o m i e n  
S i . l 4 a 1 s c u c h i l l a s d  
m ó v i l e s .  
l a s m a n o s , l o s p i e s y l a r o p a l e j o s d e l a s p i e z a s  
h a c e r l o a s í . S i e l m o t o r e s t á f u n c i o n a n d o , m a n t e n g a  
o p e r a c i ó n a m e n o s q u e s e l e i n d i q u e e s p e c í f i c a m e n t e  
N u n 3 c . a r e a l i c e a j u s t e s a l a m á q u i n a c o n e l m o t o r e n  
E s t a 2 c . i o n e l a m á q u i n a e n t e r r e n o p l a n o .  
m á q u i n a .  
S ó l o 1 p . e r m i t a q u e p e r s o n a l e n t r e n a d o d é s e r v i c i o a l a  
m á q u i n a m i e n t r a  
p e r s o n a s , n i p e r m  
O
C E N A M A L I E M N O A T Y  
M A N T E N I M I E N T  
d i r i j a N l O a d 1 e 3 s . c a r g a d e l  
N . U 0 N 2 C A d e j e l a m á q u i n a f u n c i o n a n d o s i n a t e n c i ó n .  
e n l a p o s i c i ó n b a  
.
i n f o r m a c i ó n s o b r e l o s a j u s t e s d e l m o t o r  
o p e r N e O s i n 1 2 l a . t o l v a d e  
m a n u a l d e l o p e r a d o r d e l m o t o r p a r a o b t e n e r  
o p e r e a m a y o r v e l o c i d a d d e l a n o m i n a l .  
N . o 9 c 1 a m b i e l o s a j u s t e s d e l c o n t r o l a d o r d e l m o t o r n i  
d a ñ o s .  
c o r t e y l a s p a r t e s  
M . a 1 n 1 t e n g a l a s m a  
e a V e l  
d i s m i n u i r l a v i s i b i l i d a d .  
a r b u s t o s , á r b o l e s , u o t r o s o b ! j e O t o s T q I V u e p u e d a n  
e n T g . a 8 c 1 u i d a d o a l a p r o A x V i D L m E O a T r s e a e s q u i n a s c i e g a s ,  
D E S C A R G A P O  
¡ N U N C A P O N G  
O T R I A S G I R A  
u n r e m o l q u e o u n c a m i ó n .  
e n T g . a 7 c 1 u i d a d o a l c a r  
C U C H I L L A S  
g a r l a m á q u i g n a a r e o n d e s c a r  
O :  
P E L I G R  
d r o g a s .  
N . O 6 1 o p e r e e l e q u i p o b a j o l a i n f l u e n c i a d e a l c o h o l o  
c u c h i l l a s e s t é n g i  
N . u 0 n 1 c a l e v a n t e l a  
c e r e b r a l y l a m u e r t e .  
m o n ó x i d o d e c a r b o n o q u e p u e d e n c a u s a r d a ñ o  
g a s e s d e e s c a p e s o n p e l i g r o s o s y c o n t i e n e n  
á r e a e n c e r r a d a s i n v e n t i l a c i ó n a p r o p i a d a . L o s  
N O o p e r e e l m o t o r d e n t r o d e u n e d i f i c i o n i e n u n  
r e c i p i e n t e d e l r e c  
d e t e n g a n c o m p l e  
A p a 9 g . u e e l m o t o r  
O :  
P E L I G R  
c é s p e d .  
g r a v a . D e t e n g a l  
a n t e s d e c r u z a r c  
D e s c 8 o . n e c t e l a p o  
u n a q u e m a d u r a .  
l o s u f i c i e n t e m e n t e c a l i e n t e s c o m o p a r a c a u s a r  
d e s p u é s d e d e t e n e r l o . E s t a s z o n a s p u e d e n e s t a r  
m o t o r e s t á f u n c i o n a n d o , n i i n m e d i a t a m e n t e  
l e n t a m e n t e .  
h a c i a l a p a r t e p o  
c o r t a r e n r e v e r s a  
o b s e r v a r t o d a e l  
q u e s e a a b s o l u t a  
U C I Ó N : P R E C A N o t o q u e e l m o t o r n i e l s i l e n c i a d o r m i e n t r a s e l  
. N o c o r t e e n r e v e r a s n a t e a s m d e n r o e s t r o c e d  
D e s c 7 o . n e c t e l a p o  
c o r t a c é s p e d , d e t e n e r e l m o t o r y q u i t a r l a l l a v e .  
m á q u i n a s i n a t e n c i ó n , c o m o d e s c o n e c t a r e l  
C A I Ó N )  
C I O N E S D E C O O P E N R S A I D E  
( C O N T I N U  
C I Ó N  
o m T . e 5 t 1 o d a p r e c a u c i ó n p o s i b l e c u a n d o d e j e l a  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
A S A P D O O R B O S A H P A R  
C I O N E S  
S I E M P R E C U M P L A C O N L A S O P E R A  
o p e r e l a m á q u i n a .  
p e r m N i O t a q u e p e r s o n a l s i n e n t r e n a m i e n t o  
m á q u i n a s i u  
. E s t é a t e n t o y a p a g u d e i l s a t i n t o d e l o  
b o r d e o s i e l b o r d e s e d e r r u m b a .  
r e p e n t i n a m e n t e s i u n a r u e d a p a s a e n c i m a d e u n  
n i t e r r a p l e n e s . L a m á q u i n a p o d r í a v o l c a r s e  
c o r t e y a l c u i  
p r e s e n t e s . M  
c u a T n E d o n i ñ o s N y O / o 4 C . o O t r R a s p  
, z a n j a t s i r c e a l e s  
t e c c e o r c r a N d O e p e n d i e n t e s v  
f i r m e m e n t e l a s a s a s y c a m i n e - - - n o c o r r a .  
m a n t e n g a e S l I e E q M u P i l i R b r E  
f u n c i o n e n c o  
A s e g 3 ú . r e s e q  
M . i a o n t e n g a  
n i a r r a n q u e s o p a r a d a s e n u n a p e n d i e n t e .  
d e c o r t e d e s c  
e s t á n e n l a p o  
A r r a 2 n . q u e e l  
O p e r e l a m á q u i n a s u a v e m e n t e , s i n g i r o s r e p e n t i n o s ,  
a d i c i o n a l p a r a d e t e n e r s e .  
h ú m e d a s o r e s b a l a d i z a s  
m r i e t a P . u n a d i s t a n c i a  
s e g u r a y e f i c  
o p e r a c i ó n d e  
E s i m p o r t a n t  
c o n t o d o s l o s  
A n t 1 e s . d e o p  
a l o p e r a r e n p e n d i e n t e s , o e n s u p e r f i c i e s  
R e d u z c a l a v e l o c i d a d y t e n g a c u i d a d o a l g i r a r o  
p e n d i e n t e .  
.
c u a n d o s e a p o s i b l e . N u n c a s u b a y b a j e l a  
d e s p l á c e s S e I E a M t r a P v R é E s d e l a p e n d i e n t e  
C I Ó N  
C I O N E S D E C O O P E N R S A I  
o p e r e e n d i c h a p e n d i e n t e .  
p e n d i e n t e s i n q u e l a s r u e d a s r e s b a l e n , n o l a  
l a m á q u i n a n o p u e d e r e t r o c e d e r e n u n a  
r e t r o c e d e r ( c o n l a p l a t a f  
m o n t a j e d e l  
e r V i f . i q 1 u 1 e a i n t e  
S i  
a r a P .  
t e b a j a ) . m a o r d e c o r  
p r o b a r s i p u e d e t r a b a j a r e n u n a c u e s t a , t r a t e d e  
e n p e n d i e n t N e s O e O m P p E i n R a E d a s  
.
m o t o r y q u  
r e t i r a r e l m  
d e s c a r g a .  
N O u s e l a m  
T E N C V E I A A R : D  
T E N C V E I A A R : D  
o c u l t o s .  
n u e v a . P r e s t e a t e n c i ó n a p o s i b l e s p e l i g r o s  
á r b o l e s , e t c . ) . I n g r e s e c o n p r e c a u c i ó n a u n á r e a  
s u b t e r r á n e o s ( a s p e r s o r e s , t u b o s , r a í c e s d e  
c a b e z a ( r a m a s b a j a s , e t c . ) , o b s t á c u l o s  
t o d o m o v i m i  
, q u i t e m l a o t l o l a r v e d e e  
S i . l 0 a 1 d e s c a r g  
c o n l a s o b s t r u c c i o n e s p r e s e n t e s a r r i b a d e s u  
a l e j a d o d e t o d a p e n d i e n t e v e r t i c a l .  
o t r o s p e l i g r o s o c u l t o s e n e l t e r r e n o . M a n t é n g a s e  
P r e . s B t e a t e n c i ó n a a g u j e r o s , p i e d r a s , r a í c e s y  
e s t é n c o r r e c t  
c é s p e d o p c i o  
d e s c a r g a l a t e  
e n l a p o s i c i ó  
S i e m 9 p . r e d e b  
e n T g a c u i d a d o  
a r t i f i c i a l .  
C o . r t A e e l c é s p e d s ó l o c o n l u z d e d í a o b u e n a l u z  
l a p é r d i d a d e c o n t r o l :  
E l u 6 s o . d e l a m á q u i n a r e q u i e r e a t e n c i ó n . P a r a e v i t a r  
C A I Ó N )  
( C O N T  
C I Ó N O P E R A  
C I O N E S P R E C V O I A N S S I A  
p a s a j e r o s . N O 5 L . L E V E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
c o m b u s t i b l e .  
c h i s p a s , l e j o s d e l t a n  
f ó s f o r o s o c e r i l l o s , e t  
A . M a n t e n g a l o s  
E 8 5 d a ñ a r á s e v e  
c o m b u s N t i O b l e u E s e 8 5 . E l u s o  
D E S C A R G A , O S I N E L R E C O G E D O R D E C É S P E D I N S T A L A D O S .  
N O O P E R E S I N E L E Q U I P O M E Z C L A D O R D E P A J A D E L A T O L V A D E  
A D V E R T E N C I A  
i n f l a m a b l e y l o s v  
a l m a n i p u l a r g a s o  
p e r s o n a l e s o d a ñ o  
m á x i m o d e 1 0 % d  
r e c i e n t e c o n u n o c  
L l e . n 7 e e l t a n q u e d e  
m u e v a l o s s e g u r o s d e n e u t r a l a n e u t r a l .  
a c c i o n a m i e n t o d e l a c u c h i l l a a l a p o s i c i ó n O F F y  
t r a n s m i s i ó n a n e u t r a l , m u e v a e l i n t e r r u p t o r d e  
A n t e 8 s . d e t r a t a r d e a r r a n c a r e l m o t o r , c a m b i e l a  
f i r m e m e n t e .  
f u n c i o n a n d o d  
e q u i p o c o n e l s  
t r a n s m i s i ó n n o  
t r a n s m i s i ó n d e  
l i b e r a l a s p a l a n  
n e u t r a l . E l s i s  
p l a t a f o r m a e s t  
m o t o r a r r a n q u  
o p e r a d o r y a t e  
b l o q u e o d i s e ñ  
E s t a m á q u i n a  
J . C o l o q u e n u e v a m e n t e l a t a p a d e g a s o l i n a y a p r i e t e  
i n m e d i a t a m e n t e .  
I . S i d e r r a m a c o m b u s t i b l e e n l a r o p a , c á m b i e s e l a  
e n p o s i c i ó n a b i e r t a .  
N o u t i l i c e u n d i s p o s i t i v o q u e b l o q u e e l a b o q u i l l a  
r e c i p i e n t e h a s t a t e r m i n a r d e l l e n a r e l c o m b u s t i b l e .  
t a n q u e d e c o m b u s t i b l e o c o n l a a b e r t u r a d e l  
M . a n H t e n g a l a b o q u i l l a e n c o n t a c t o c o n e l b o r d e d e l  
d e u n d i s p e n s a d o r d e g a s o l i n a .  
r e c i p i e n t e p o r t á t i l e n l u g a r d e u s a r u n a b o q u i l l a  
n o e s p o s i b l e , a ñ a d a e l c o m b u s t i b l e c o n u n  
T E N C V E I A A R : D  
r e e m p l á c e l o s a n t  
c a l c o m a n í a e s t á n  
u n a g u a r d a , u n d i  
g u a r d a s y d i s p o s i  
c o n d i c i o n e s d e o  
M a n 6 t e . n g a l a m á q  
a b a s t é z c a l a d e c o m b u s t i b l e e n e l t e r r e n o . S i e s t o  
G . R e t i r e l a m á q u i n a d e l c a m i ó n o d e l r e m o l q u e y  
a b a s t e c e r l o s d e c o m b u s t i b l e .  
. S i  
e n e l t e r r e n o l e j o s d e s u v e h í c u l o a n t e s d e  
m a t e r i a l p l á s t i c o . S i e m p r e c o l o q u e l o s r e c i p i e n t e s  
e n u n c a m i ó n o r e m o l q u e q u e t e n g a f o r r o d e  
F . N u n c a l l e n e r e c i p i e n t e s d e n t r o d e u n v e h í c u l o n i  
t i e m p o p u e d e c a  
e s t a m á q u i n a p  
S i e m p r e u s e p r  
a g u a u o t r o s a p a r a t o s .  
c h i s p a o l u z p i l o t o , c o m o d e u n c a l e n t a d o r d e  
d e c o m b u s t i b l e d o n d e h a y a u n a l l a m a T a b E i e r N t a , C V E I A A R : D  
E . N u n c a a l m a c e n e e l c o r t a c é s p e d o e l r e c i p i e n t e  
l o c a l e s y n o r m a s  
c a s c o , p u e s e s r e  
l l e v a r g a f a s d e s e  
i n c l u y e n d o p a n t a  
c o r t o s ; s i e m p r e l  
m ó v i l e s . N o o p e r  
c a b e l l o l a r g o o l a  
S i e m 5 p . r e u s e r o p a  
b a j o t e c h o n i e n u n r e m o l q u e c e r r a d o .  
D . N u n c a a b a s t e z c a d e c o m b u s t i b l e a l c o r t a c é s p e d  
a g r e g a r e l c o m b u s t i b l e .  
m o t o r s e e n f r í e p o r v a r i o s m i n u t o s a n t e s d e  
o p e r a c i ó n n i a u n m o t o r c a l i e n t e . P e r m i t a q u e e l  
c o m b u s t i b l e N a O u C n a . g m r o e t g o u r e e n  
U s . e B s o l a m e n t e u n r e c i p i e n t e a p r o b a d o p a r a g a s o l i n a .  
C A I Ó N )  
( C O N T I N U  
C I Ó N  
C I O N E S P R E C V O I A N S S I A D E L  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
l a s c u c h i l l a s .  
o b j e t o s q u e p u d i e r a n s e r r e c o g i d o s y a r r o j a d o s p o r  
R e t i 4 r e . d e l á r e a q u e d e b e s e r c o r t a d a t o d o s l o s  
c a u s a s q u  
e l m e n s a j  
¡ P a r a e v i t  
s í m b o l o c  
d e l e q u i p o  
s o b r e m e  
s i g u i e n t e s  
l a m á q u i n a , n o e s u n j u g u e t e .  
q A u e l o s n i ñ o s s e N s O u b 3 P a . n E R o M j u e I g T u e n e n  
c a l i f i c a d a s o p e r e n o d e n s e r v i c i o a e s t a m á q u i n a .  
p e r m i t a q N u U e N n 2 i . C ñ A o s o p e r s o n a s n o  
c o n t r o l e s d e l o p e r a d o r y l a s s e ñ a l e s d e s e g u r i d a d .  
E l s í m b o l o s e u s a c o n l a s r i e s g o p a  
E s t e s í m  
F a m 1 i l . i a r í c e s e c o n l a o p e r a c i ó n s e g u r a d e l e q u i p o , l o s  
C I Ó N  
A L A O P E R A  
C I O N E S P R E C V O I A N S S I D E R A  
y l a s p r á c t i c a s d e o p e r a c i ó n c o r r e c t a d e e s t a m á q u i n a .  
q u e u s t e d c o n o z c a y c o m p r e n d a t o d o s l o s p r o c e d i m i e n t o s  
S u s e g u r i d a d y l a d e l o s d e m á s d e p e n d e n e n g r a n p a r t e d e P A L A  
S c a g c u a  
m o d e l o y  
f o r m u l a r  
u t i l i z a n d  
s c a g . c o m  
d e n o s e g u i r s e , s e p u e d e n o c a s i o n a r l e s i o n e s p e r s o n a l e s .  
s e g u i r p r á c t i c a s s e g u r a s e n o c e r c a d e l a m á q u i n a y q u e  
( P R E C A U C I Ó N ) e s u n r e c o r d a t o r i o d e q u e s e d e b e n  
L a p a l a b r a d e s e ñ a l i z a c i ó n “ C A U T I O N ”  
.
W I 5 3 0 5 0 , M o a v y i v s i t l a l e n  
E q u i p m e  
U C I Ó N : P R E C A  
. O . B o x 1 5 2 ,  
a u t o r i z a d  
H a y d i s p  
m u e r t e s i n o s e t o m a n l a s p r e c a u c i o n e s d e b i d a s .  
c e r c a d e l a m á q u i n a q u e p u e d e o c a s i o n a r l e s i o n e s o l a  
e s r e s p o n  
S i e l o p e  
T E N C I A ) ( A i n D d V i c E a R q u e e x i s t e u n r i e s g o e n o  
L a p a l a b r a d e s e ñ a l i z a c i ó n “ W  
A R N I N G ”  
A T C É S P E D .  
A N T E S D E O P E R D A E D L O R  
A R R A N A C T R A R D E S T U R A C O R  
E S T L E E M A A N  
T E N C V E I A A R : D  
e l l o s m i s  
r e s p o n s a  
t o m a n l a s p r e c a u c i o n e s a p r o p i a d a s .  
d e o c a s i o n a r l a m u e r t e o u n a l e s i ó n i r r e p a r a b l e s i n o s e  
e n o c e r c a d e l a m á q u i n a , q u e t i e n e a l t a s p r o b a b i l i d a d e s  
i n d i c a q u e e x i s t e u n a s i t u a c i ó n e x t r e m a d a m e n t e p e l i g r o s a  
c o r t a c é s p  
f a m i l i a r i  
o p e r a d o r  
y a l m a c e  
r e l a c i o n a  
p r u d e n c i  
d e a c c i d e  
g r a v e s o  
d e s c u i d o  
S u c o r t a c  
L a p a l a b r a d e s e ñ a l i z a c i ó n “ D A N G E R ” ( P E L I G R O )  
C e r c i ó r e s e d e q u e c a d a  
O :  
P E L I G R  
c o n d i c i ó n d e p e l i g r o .  
m a n u a l p a r a a l e r t a r s o b r e l a e x i s t e n c i a y e l g r a d o d e u n a  
. E l e r r o r o  
l a s c a l c o m a n í a s d e s e g u r i d a d d e l e q u i p o y a t r a v é s d e e s t e  
L a p a l a b r a d e s e ñ a l i z a c i ó n e s d i s t i n t i v a y s e D e n A c u e n t r a e n S E G U  
C I Ó N G E N I N E F R O A R L  
P a l a b r a d e s e ñ a l i z a c i ó n :  
A D  
C I Ó N D E S I N E F G O U R R M I D A  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
c u r i o s o s  
M a n t e n g a a l e j a d o s a l o s  
P e l i g r o d e o b j e t o s l a n z a d o s  
L e a e l m a n u a l d e l o p e r a d o r  
t r a n s c u r r i d a s  
H o r ó m e t r o / H o r a s d e o p e r a c i ó n  
E l e m e n t o c o r t a n t e – D e s c o n e c t a r  
1 0 3 9 S  
P u n t o d e c o n t a c t o  
E l e m e n t o c o r t a n t e – C o n e c t a r  
C o n t i n u a m e n t e v a r i a b l e – L i n e a l  
E l e m e n t o c o r t a n t e - S í m b o l o b á s i c o  
R á p i d o  
L e n t o  
D E S C R I P C I Ó N  
S Í M B O L O  
D E S C R I P C I Ó N  
S Í M B O L O  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
R i e s g o d e c a í d a  
A p a g a d o / P a r a d a  
E n c e n d i d o / A r r a n q u e  
O b j e t o s l a n z a d o s  
A c e i t e  
e n T s i ó n d e l r e s o r t e e n l a p o l e a  
4 8 0 7 1 S  
C u c h i l l a g i r a t o r i a  
F r e n o d e e s t a c i o n a m i e n t o  
A h o g a d o r  
r a T n s m i s i ó n  
D E S C R I P C I Ó N  
S Í M B O L O  
D E S C R I P C I Ó N  
S Í M B O L O  
S í m b o l o s I S O  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
d u r a n t e e l p e r í o d o d e g a r a n t í a p u e d e a n u l a r l a .  
C . u a l q u m i e o r t o r a r b a j o n o a u t o r i z a d o r e a l i z a d o e n e l m o t o r  
a u n a g e n t e l o c a l d e s e r v i c i o a u t o r i z a d o d e l f a b r i c a n t e d e l  
i m p o r t a n t e c o n t a c t a r c o n s u d i s t r i b u i d o r S c a g o e n c o n t r a r  
s e r v i c i o a l m o t o r d u r a n t e e l p e r í o d o d e g a r a n t í a l i m i t a d a , e s  
d e m a n t e n i m i e n t o d e r u t i n a y d e s e r v i c i o g e n e r a l . P a r a d a r  
c u b i e r t o s e n e s t e m a n u a l ; s ó l o s e p r o p o r c i o n a n i n s t r u c c i o n e s  
L o s d e t a l l e s s o b r e s e r v i c i o y r e p a r a c i ó n d e l m o t o r n o e s t á n  
e l a  
o b l i g a c i ó n .  
m o m e n t o s i  
r e s e r v a e l d  
a p r o b a r s e l  
i n f o r m a c i ó n  
o d T a l a i n f o r m  
O T R  
V I C I O S E A R L M O  
.
e s t o s a c c e s o  
n i n g u n a c i r c  
l a s g u a r d a s o  
f i g u r a s e n e s  
P a r a u n a m e j  
a d e l a n t e .  
n o r m a l y d e c a r a a l a d i r e c c i ó n d e d e s p l a z a m i e n t o h a c i a  
o p e r a d o r c u a n d o s e e n c u e n t r a e n p o s i c i ó n d e o p e r a c i ó n  
d e l a m á q u i n a s e r e f i e r e n a l a i z q u i e r d a y d e r e c h a d e l  
L o s l a d o s “ d e r e c h o ” e “ i z q u i e r d o ” , “ f r o n t a l ” y “ p o s t e r i o r ”  
G A R A N T Í A  
A N U L A R Á L A O R I G I N A L E S S E A N S C A  
R E F E R E N C I A D E I N S T R U C C I O N E S  
E L U S O D E  
B l a d e B u d d y ( n / p 9 2 1 2 )  
D e f l e c t o r t u r b o ( n / p 4 2 4 2 0 8 )  
H o r ó m e t r o ( n / p 4 8 0 2 3 )  
S u j e t a v a s o s ( n / p 9 2 4 0 )  
9 2 8 3 , 9 2 8 4 )  
S E G U R I D A  
R E N D I M I E  
A F B R I E C L A N T E P U  
O Q U E N O R E E P S U T E É S T  
E S T E P R O  
P O R  
O R I Z A A U D T A  
( n / p 9 2 6 3 ,  
S i s t e m a m e z c l a d o r d e p a j a H u r r i c a n e  
T M  
P l a c a d e s m e n u z a d o r a ( n / p 9 2 5 8 , 9 2 8 6 , 9 2 8 7 )  
T E R A D E  
R E E E L M P L A Z O  
G C - 4 D ( n / p 9 0 5 4 )  
G C - F 4 ( n / p 9 0 5 5 )  
l í n e a c o m p l e  
d e t r a b a j o o  
p r o p o r c i o n a r  
m é t o d o s p a r  
d i s t r i b u i d o r e  
d i s t r i b u i d o r c  
L e s u g e r i m o  
G :  
G .  
P O R S C A  
A C C E S O R I O S Y  
A D O S B A P R O S  
A M E N A T D I T  
d e c o n d u c c i ó n “ v e r t i c a l e s ” ) p u e d e s e r p e l i g r o s o .  
d i s p o s i t i v o s n o a p r o b a d o s , ( e s p e c i a l m e n t e l o s d i s p o s i t i v o s  
a p r o b a d o s p a r a u s a r l o s e n e s t a m á q u i n a . E l u s o d e  
q u e n o s e a n l a p r o p i a S c a g P o w e r E q u i p m e n t n o e s t á n  
L o s a c c e s o r i o s y a d i t a m e n t o s f a b r i c a d o s p o r c o m p a ñ í a s  
o d T o s l o s  
c o n s u d i s t r i b  
S i r e q u i e r e i n  
P O R S C A  
S Ó L O U S E D I S P O S I T I V  
A D O S B  
O S A P R  
m a n u a l .  
4 8 1 1 0 9 S P  
L E A E L M A N U A L D E L O P E R A D O R  
C O N D U C C I Ó N A P R O B A D O S P O R S C A G  
S Ó L O U S E D I S P O S I T I V O S D E  
R I E S G O D E C A Í D A  
d e o p e r a c i ó n  
c o r t a c é s p e d  
v i d a ú t i l y e l  
e x i g e n t e s d e  
S u c o r t a c é s p  
A D V E R T E N C I A  
I N T R O D  
C I Ó N G E N I N E F R O A R L M A  
Download from Www.Somanuals.com. All Manuals Search And Download.  
I I  
i o r  
3 4 - 3 5  
3 3  
t a p o s t c e u r b i e r  
. . . . . . . . . . . . .  
D e n t r o d e l a  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D e c l a r a c i ó n d e g  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C . . a . . l . c . . o . . m . . . a . . n . . í . a . . s . . . d . . e . . . r  
, 1 6 H P H P y 1 7 a H s w P a k ) i ( 1 5 l e s - K a o d e c a b  
A d a p t a d o r d e l m a  
2 3  
2 3  
1 3  
0 3  
2 8 - 2 9  
2 6 - 2 7  
5 2  
4 2  
2 2 - 2 3  
2 0 - 2 1  
. . . . . . . . . . . . m . . . a . . n . . g . . o . . . . . . . . . . . . . . . . . . . . . . . M . . . a . . z . . o . . . d . . e . . . c . a . . b . . l . e . . s . . . d .  
. . . . . . . . . . . m . . . o . . t . o . . r . . . . . . . . . . . . . a . . t . a . f . o . . r . . m . . . a . . . d . . e l  
M a z o d e c a b l e s d  
. . . . . . . . l . e . . s . . s e . . e P . . r . . . . . . . . . . . . . . . . a . r . n . T . s . . m . . . i s . . i . ó . . n . . . . . . . . . . . . . . . .  
. . . . . . . . . . . . . . . u . . m . . . e . . n . . t . o . . s . . . . . . . l . e . b . r . a o . . T . d . . e . . . i . n . . s . . t . r . . . . . . . . . . . . . . .  
. . . . . . . . . a . . n . . g . . o . . . . . . . . . . . . . . . . . . . C . . o . . n . . j . u . . n . . t . o . . . d . . e . . l . . m . . . . . .  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P . . l . a . . t . a . . f . o . . r . m . . . a . . . d . . e . . l . . m . . o .  
. . . . . . . . l . i . b . . r . e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C . . o . . n . . j . u . . n . . t . o . . . d . . e . . . l . a . . . r . u . .  
. . . . . . . . . . . . N . . o . . t . a . . s . . . . . . . . . . . . . . . . . . . .  
. . . . . . . . . . . . . . . . . . . . . . . . S . . W . . t . e . M . . . - . 4 . . 8 . . " . , . . 5 . . 2 . m . " . . a o . . r d . . e . . . c . . P o . . r l . a . . t . a f  
. . . . . . . . . . . . . . . . . . . . . . . . S . . W . . t . e . M . . . - . 3 . . 2 . . " . , . . 3 . . 6 . m . " . . a o . . r d . . e . . . c . . P o . . r l . a . . t . a f  
L i s t a d e p a r t e s i l  
T E M A  
P Á G I N A  
C A I Ó N )  
( C O N T I N U  
A T B L A D E C O N T E N I D O  
Download from Www.Somanuals.com. All Manuals Search And Download.  
I
C E R T I F I C A T I O N  
T E C H N I C I A N  
W E S U P P O R T O P E  
1 9 - 2 1  
1 6 - 1 8  
. . . . . . . . . . . . . . é . . c . . n . . i c . . a . . s . . . . . . . . . . . . . . . . . . . E . . s . . p . . e . . c . . i . f . i c . . a . . c . . i . o . . n . . e . . s . . . t . . . .  
e n l a s a l c l a o s n d i c i o n e s d e I d e n t i f i c a c i ó n d e f  
. . . . t . e . . . . c . . o . . r . . . . . . . . . . . . . . . . . . . . . . . .  
5 1  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i . c . . a . . c . i . ó . . n . . . y . . . M . l a b a d a n T e t e L n u i m b i r e n t o  
. . . . . . . . . . . . . . . m . . . á . . q . . u . . i . n . . a . . . . . . . . . . . . . L . . i . m . . . p . . i e . . z . . a . . . d . . e . . . l . a . . . . . . . . . . .  
4 1  
4 1  
4 1  
3 1  
2 1  
1 1  
. . . . . . . . . . m . . . o . . t . o . . r . . . . . . . . . . d . . e . . . a . . i . r . e . . . d . . e . . l . . . . . . . .  
. . . . . . . . . . . . . . . . . . . . . i . t . e . . . d . . e . . l . m . . . o . . t . o . . r . . . . . . . . . . . . . . . . . . M . . . a . n t e n i m i e n t o d e l a c  
. . . . . . . . . . . . . . . . . . . . . . . . . . . t . e . . . p . . e . . r . s . . o . . n . o . a . r . l . i . z d . a . e . d c o o r A j u s t e d e l d e f l e c t  
M a n t e n i m i e n t o d e l f i l  
. . . . t . e . . . . . . . . . . . . . . . . . . . . . . . . . C . . u . . c . . h . . i . l . l . a . . s . . d . . e . . . . c . o . . r . . . . . . . .  
. . . . t . e . . . . . . . . . d . . e . a . . c . . o . . r . . . . . . . . . . . . . . . . . . . . . A . . j . u . . s . . t . e . . . d . . e . . . l a . . . a . . l . t . u . . r . . . . .  
. . . . e . t . . . . . . . . . . . . . . . . m . . . a o . . r . d . . e . . c . . o . . r . . . . . . . . . . . . . . . . . . . A . . j . u . . s . . t . e . . s d e l a p l a t a f  
. . . . . . . . . . . . . l . . m . . . o . . t . r . i . z . . . . . . . . . . . . . . . . . . A . . j . u . . s . . t . e . . s . . d . . e . . . c . . o . . n . . t . r . o . . . . . . .  
. . . . . . . . . . . . . . . . . . . . t . r . a . . n . . s . . m . . . i . s . . i ó . . n . . . . . C . . o . . r . . r . e . . a . . . d . . e . . . l a . . . . . . . . . . . . . . .  
1 0 - 1 1  
0 1  
0 1  
9
. . . . t . e . . . . . . . . . . . . . . . m . . . a o . . r . d . . e . . . c . . o . . r . . . . . . . . . .  
A j u s t e s d e l a c o r r e a  
8 - 9  
. . . . . . . . . . . . . . . . t . a . . c . . é c . . s o . . p r . . e . . d . . . . . . . . a . . c . . i ó . . n . . O . d . . p e . . e l . . r . . . . . . . . . . . . . . . . . . . . .  
8
. . . . . . . . i c . . i . a . . l . . . . . . . . . . . . . a . . r . r . a . . n . . q . . u . . e . . . i . n . . . . . . . . . . . . . . . P . . r . o . c e d i m i e n t o s d e  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M . . . a . . n . t e n i m i e n t o y A l m  
. . . . . ó . . n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C . . o . . n . . s . . i . d . . e . . r . a . . c . . i o n e s d e  
7 - 8  
6 - 7  
4 - 6  
4
4
2 - 3  
1
. . . . . . . . . . . . . . . . . o . . p . . e . . r . . a . . c . i . ó . . n . . . . . . . . . . . . . . . . . . . . . .  
C o n s i d e r a c i o n e s p r e  
. . . . . . . . . . . . . . . . . . . . . . . . . . . d . . e . . . a s . . e s . . ñ . . a . . a l i . z . l P a . a . b . c . r . i . ó . n . . . . . . . . . . . . . . . . . . . . . . . . .  
. . . . . . . d . . a . . d . . . . . . . . . . . d . . e . . . s . . e . . g . . u . . r . i . . . . . . . . . . . . . . . . . . . . . I n s t r u c c i o n e s g e n e r a  
. . . . . . . . . . . . . . . . . S . . í . m . . . b . . o . . l . o . . s . . . . . . . . . . . . . . . . . . .  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . S . . e . . r . v . . i . c . . i . o . . . a . . l . m . . . o . . t . o . . r . . . . . . .  
1
1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R . . e . . f . e . . r . e . . n . . c . . i . a . . . d . . e . . . i . n . . s t r u c  
. . . . . . . . . . . . . . . . . . . . . I . n . . t . r . o . . d . . u . . c . . c . . i ó . . n . . . . . . . . . . . . . . .  
P Á G I N A  
T E M A  
M O D E L O S W  
A T B L A D E C O N T E N I D O  
Download from Www.Somanuals.com. All Manuals Search And Download.  
c o m p l e t o q u e a p a r e c e e n l  
C u a n d o s e r e f i e r a a e s t e p  
c o n n ú m - e 1 r 7 o K d A e I S s W e r 5 i e 2 V d e D 6 2  
c o n n ú m - e 1 r 6 o K d A e I S s W e r 4 i e 8 V d e D 6 1  
c o n n ú m - e 1 r 5 o K d H e S s W e r 4 i e 8 V d e D 6 0  
n ú m e c r o o n d e s e r i e d e S D W 5 9 3 0 6 0 A 0 - 0 1 1 6 K a A  
c o n n ú m e r o d e S s W e r 3 i e 6 A d - e 1 5 D K 5 H 8  
c o n n ú m e r o d e S s W e r 3 i e 2 - d 1 e 5 K D A 5 I 7  
l i s t a d e p a r t e s i l u s t r a d a s p a r a :  
E s t e m a n u a l c u b r e l a s i n s t r u c c i  
o p e r a c i ó n , e l t r a n  
i n t e r é s , l a p r u d e n  
E l c o n t r o l d e r i e s  
O C O M O E L A T N O P S E E R G A U D R O R C ! A É T S P E D E S  
R E C U E R D  
c o n t r o l d e d i r e c c i ó n .  
N O * c o r t e e n c é s p e d m o j  
O S H A .  
A P R O B A D A S P O R  
C O N L A S O P E R A C S I O I E N M E P S R E C U M P L A  
r e s b a l e n , r e d u z c a l a v e l o  
S i l a m á q u i n a p u e d e r e t r  
e n u n a c u e s t a , t r a t e d e r e  
N O * O P E R E e n p e n d i e n t  
d e b e u s a r l o a l a v e z ) .  
M a * n t e n g a a o t r a s p e r s o n  
p r o p o r c i o n a d o c o n s u c o  
L e * a e s t e m a n u a l c o m p l e  
M a * n t e n g a l a s m a n o s , l o s  
a s c a , d e t e n g a e l m o t o r S a i n * u t n e s m d e e c a l i m n i p s m i a r o s e a t  
m á q u i n a y q u i t e e l c a b l e  
.
A n * t e s d e r e a l i z a r c u a l q u i  
t o l v a d e d e s c a r g a d e c é s  
M a * n t e n g a t o d a s l a s g u a  
V E S .  
A T R E N L E S I O N E S G R A  
O P E R A C I Ó N P U  
E L I N C U M P L I M I  
Download from Www.Somanuals.com. All Manuals Search And Download.  
I M P R E S O E N E E . U U .  
I M P R E S O E N A B R I L D E 2 0 0 7  
A P R T E N º 0 3 2 2 4  
Y V I L L E , I N C .  
A L C R A F T O F M A D I V I S I O N O F M E T  
S C A G P O W E R E Q  
2 © 0 0 7  
L A I N F O R M A C I Ó N I N C L U I D A .  
A N T E S D E O P E R A R S U M Á Q U I N A  
I N D I C A D O S E N L A  
I A N T T E R I O R . C U B I E R  
E S T Á N  
O T S P O R E C S U T B E I E M R A N U A L  
E F I C I E N C I A . L O S M O D E L O S E S  
A T C É S C P E O D R T R A B A J A N D O  
F A I N D E M A A J U N D S T T E E E N E R S U  
L Y O S O P R O C E D I M I E N T M A N T E N I M I E N T  
Y A U D A R E N E L L E P U E D M E A N U A L  
D E E S T E L E C . T L U A R A A T C É S C P E O D R S C A G  
S U A R A I N F O R M A C I Ó N D E S E G U R I D A  
I N S T R U C C I O N E S D E O P E R A C  
E S T E M A N U A L C O N T I E  
M Á L X A A I M A  
O S  
L Y A  
M O D E L O  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Ames True Temper Lawn Mower PW4 page
Husqvarna Lawn Mower 1030 BioClip User Manual
Land Pride Lawn Mower RB0548 User Manual
Scag Power Equipment Lawn Mower SWZ 19KAI User Manual
Snapper Lawn Aerator 4534 User Manual
Snapper Lawn Mower 12RTG36 User Manual
Snapper Lawn Mower PMA8610 User Manual
Snapper Lawn Mower SV212 User Manual
Snapper Lawn Mower ZT20500BV User Manual
Weed Eater Lawn Mower 159411 User Manual