Chariot Brutus
GBKW2552S, GBKH2752S
GBKW2561S, GBKH2761S
TCU20866
C5
OPERATOR’S MANUAL
200315 03/06/2006
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Introduction
Using Your Operator’s Manual
This manual is an important part of your machine and should remain with
the machine when you sell it.
Use the safety and operating information in the machine operator’s
manual to operate and service the machine safely and correctly.
An engine manufacturer’s owner’s manual has been provided with your
machine. This will provide maintenance and troubleshooting information
for the engine installed in your machine.
Specifications and design are subject to change without notice.
WARNING: The Engine Exhaust
from this product contains chemicals known
to the State of California to cause cancer,
birth defects or other reproductive harm.
Special Messages
Your manual contains special messages to bring attention to potential
safety concerns, machine damage as well as helpful operating and
servicing information. Please read all the information carefully to avoid
injury and machine damage.
California Proposition 65 Warning
CAUTION: Avoid injury! This symbol and text highlight
potential hazards or death to the operator or bystanders that
may occur if the hazards or procedures are ignored.
IMPORTANT: Avoid damage! This text is used to tell the operator
of actions or conditions that might result in damage to the
machine.
NOTE: General information is given throughout the manual that may
help the operator in the operation or service of the machine.
Product Identification
Record Identification Numbers
Chariot Brutus
GBKW2552S
GBKH2752S
GBKW2561S
GBKH2761S
S/N 637910000
S/N 638010000
S/N 638310000
S/N 638410000
All information, illustrations and
specifications in this manual are based on
the latest information at the time of
publication. The right is reserved to make
changes at any time without notice.
COPYRIGHT© 2006
If you need to contact an Authorized Service Center for information on
servicing, always provide the product model and serial numbers.
You will need to locate the model and serial numbers for the machine and
for the engine of your machine and record the information in the spaces
provided.
Auburn Consolidated Industries Inc.
All rights reserved
DATE OF PURCHASE:
COPYRIGHT© 2006
_________________________________________
DEALER NAME:
_________________________________________
DEALER PHONE:
_________________________________________
Introduction - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY LABELS
The operator’s manual also explains any potential safety hazards
whenever necessary in special safety messages that are identified with
the word, CAUTION, and the safety-alert symbol.
DANGER
MODEL NUMBER (POWER UNIT) (A):
__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
SERIAL NUMBER (POWER UNIT) (A):
__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
ENGINE MODEL NUMBER(B):
To avoid injury from rotating blades, stay clear of deck edge.
__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
ENGINE SERIAL NUMBER (B):
__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
ENGINE SPECIFICATION NUMBER (B):
__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
MOWER DECK MODEL NUMBER (C):
__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
MOWER DECK SERIAL NUMBER (C):
__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __
ROPS SERIAL NUMBER (D):
Safety Labels
Understanding The Machine Safety Labels
The machine safety labels shown in this section are placed in important
areas on your machine to draw attention to potential safety hazards.
On your machine safety labels, the words DANGER, WARNING, and
CAUTION are used with this safety-alert symbol. DANGER identifies the
most serious hazards.
Safety Labels - 2
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY LABELS
DANGER
DANGER
• Cigarettes, flames or sparks could cause battery to explode. Always
shield eyes and face from battery. Do not charge or use booster cables or
adjust post connections without proper instruction and training.
Do not mow without discharge chute or entire grass catcher in place.
• Contains sulfuric acid. Avoid contact with the skin, eyes or clothing. In
event of accident, flush with water and call a physician immediately. Keep
out of reach of children.
DANGER
WARNING
To avoid injury from rotating blades and thrown objects, stay clear of deck
edge and keep others away. Do not mow without discharge chute or entire
grass catcher in place.
To avoid injury from tipover, drive across slopes, not up and down. If
machine stops going uphill, stop blades and back down slowly.
Safety Labels - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY LABELS
• Read operator’s manual
WARNING
• Keep shields in place
• Never carry riders
• Keep people a safe distance away
• Maintain all safety devices
• Before leaving machine:
• Stop engine
• Set park brake
• Remove key
WARNING
To avoid injury from rotating belts, keep all shields and guards in place.
WARNING
AVOID CRUSHING
• Keep Rollover Protective Structure fully extended
• Do not jump if machine tips
• Use seat belt
When Structure must be down
• DO NOT use seat belt
Hot surface
• Drive with extra care
CAUTION
WARNING
Seat belts are not to be mounted in this hole, because seat will not meet
SAE J386 test requirements. Failure to comply with warning could cause
serious injury or death.
• Operator training required
Safety Labels - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Emission Control System Certification Label
Preparation
NOTE: Tampering with emission controls and components by
unauthorized personnel may result in severe fines or penalties.
Emission controls and components can only be adjusted by EPA
and/or CARB authorized service centers. Contact your Great Dane
Equipment Retailer concerning emission controls and component
questions.
• Evaluate the terrain to determine what accessories and attachments are
needed to properly and safely perform the job. Only use accessories and
attachments approved by the manufacturer.
• Wear appropriate clothing including hard hat, safety glasses and
hearing protection. Long hair, loose clothing or jewelry may get tangled in
moving parts.
The presence of an emissions label signifies that the engine has been
certified with the United States Environmental Protection Agency (EPA)
and/or California Air Resources Board (CARB).
• Inspect the area where the equipment is to be used and remove all
objects such as rocks, toys and wire which can be thrown by the machine.
• Use extra care when handling gasoline and other fuels. They are
flammable and vapors are explosive.
The emissions warranty applies only to those engines marketed by Great
Dane that have been certified by the EPA and/or CARB; and used in the
United States and Canada in off-road mobile equipment.
a.Use only an approved container.
b.Never remove gas cap or add fuel when engine is running. Do not
smoke.
Emission Compliance Period
If your engine has the emission compliance category listed on the
emission control system certification or air index label, this indicates the
number of operating hours for which the engine has been certified to meet
EPA and/or CARB emission requirements. The following table provides
the engine compliance period in hours associated with the category found
on the certification label.
c.Never refuel or drain the machine indoors.
• Check that the operator’s presence controls, safety switches and shields
are attached and functioning properly. Do not operate unless they are
functioning properly.
Operating Safely
Agency
EPA
Category
Hours
250
• Never run an engine in an enclosed area where dangerous carbon
monoxide fumes can collect.
C
• Only operate in good light, keeping away from holes and hidden
hazards.
EPA
B
500
EPA
A
1000
125
• Be sure all drives are in neutral and parking brake is engaged before
starting engine. Only start engine from the operator’s position. Use seat
belts if provided.
CARB
CARB
CARB
Moderate
Intermediate
Extended
250
• Slow down and use extra care on hillsides. Be sure to travel in the
recommended direction on hillsides. For this machine, drive across
hillsides, not up and down. Turf conditions can affect the machine’s
stability. Use caution while operating near drop-offs.
500
Certification
• Slow down and use caution when making turns and when changing
directions on slopes.
Your product has been tested and evaluated by the manufacturer and
conforms with American National Standard B-71.4, “Safety Specifications”
for commercial turf care equipment.
• Never raise deck with the blades running.
• Never operate with the PTO shield, or other guards, not securely in
place. Be sure all interlocks are attached, adjusted properly, and
functioning properly.
Canadian Electromagnetic Compatibility (EMC)
Compliance
This spark ignition system complies with Canadian ICES-002.
• Never operate with the discharge deflector raised, removed or altered,
unless using a grasscatcher. Do not operate mower without discharge
chute or entire grasscatcher in place.
• Do not change the engine governor setting or overspeed the engine.
Operating the engine at excessive speed can increase the hazard of
personal injury.
Safety
Operator Training Required
• Stop on level ground, lower implements, disengage drives, engage
parking brake, and shut off engine before leaving the operator’s position
for any reason including emptying the grasscatchers or unclogging the
chute.
• Read the operator’s manual and other training material. If the operator
or mechanic cannot read English, it is the owner’s responsibility to explain
this material to them. This publication is available in other languages.
• Become familiar with the safe operation of the equipment, operator
controls, and safety signs.
• Stop equipment and inspect blades after striking objects or if an
abnormal vibration occurs. Make necessary repairs before resuming
operations.
• All operators and mechanics should be trained. The owner of the
machine is responsible for training the users.
• Keep hands and feet away from the cutting units.
• Never let children or untrained people operate or service the equipment.
Local regulations may restrict the age of the operator.
• Look behind and down before backing up to be sure of a clear path.
• Never carry passengers and keep pets and bystanders away.
• The owner/user can prevent and is responsible for accidents or injuries
occurring to themselves, other people, or property.
• Slow down and use caution when making turns and crossing roads and
sidewalks. Stop blades if not mowing. Watch for traffic when operating
near or crossing roadways.
• Operate the machine in an open, unobstructed area under the direction
of an experienced operator.
Safety - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
• Be aware of the mower discharge direction and do not point it at anyone.
Parking Safely
• Do not operate the machine while under the influence of alcohol or
drugs.
1.Stop machine on a level surface, not on a slope.
2.Move motion control levers out to the neutral lock position.
3.Disengage mower blades.
• Use care when loading or unloading the machine into or off of a trailer or
truck.
4.Lower attachments to the ground.
5.Lock the park brake.
• Use care when approaching blind corners, shrubs, trees, or other
objects that may obscure vision.
• Inspect machine before you operate. Be sure hardware is tight. Repair
or replace damaged, badly worn, or missing parts. Be sure guards and
shields are in good condition and fastened in place. Make any necessary
adjustments before you operate.
6.Stop the engine.
7.Remove the key.
8.Wait for engine and all moving parts to stop before you leave the
operator’s seat.
• Before using, always visually inspect to see that the blades, blade bolts
and the mower assembly are not worn and damaged. Replace worn and
damaged blades and bolts in sets to preserve balance.
9.Close fuel shut-off valve, if your machine is equipped.
10.Disconnect the negative battery cable or remove the spark plug wire
(for gasoline engines) before servicing the machine.
• Keep safety labels visible when installing accessories and attachments.
• Do not wear radio or music headphones. Safe service and operation
require your full attention.
Rotating Blades are Dangerous
HELP PREVENT SERIOUS OR FATAL ACCIDENTS:
• When machine is left unattended, stored, or parked, lower the mower
deck unless a positive mechanical lock is used.
Using a Spark Arrestor
The engine in this machine is not equipped with a spark arrestor muffler. It
is a violation of California Public Resource Code Section 4442 to use or
operate this engine on or near any forest-covered, brush-covered or
grass-covered land unless the exhaust system is equipped with a spark
arrestor meeting any applicable local or state laws. Other states or federal
areas may have similar laws.
A spark arrestor for your machine may be available from your authorized
dealer. An installed spark arrestor must be maintained in good working
order by the operator.
Checking Mowing Area
• Rotating blades can cut off arms and legs, and throw objects. Failure to
observe safety instructions could result in serious injury or death.
• Keep hands, feet and clothing away from mower deck when engine is
running.
• Be alert at all times, drive forward carefully. People, especially children
can move quickly into the mowing area before you know it.
• Do not mow in reverse.
• Shut off blades when you are not mowing.
• Park machine safely before leaving the operator station for any reason
including emptying the catchers or unplugging the chute.
• Clear mowing area of objects that might be thrown. Keep people and
pets out of mowing area.
• Low-hanging branches and similar obstacles can injure the operator or
interfere with mowing operation. Before mowing, identify potential
obstacles such as low-hanging branches, and trim or remove those
obstacles.
• Study mowing area. Set up a safe mowing pattern. Do not mow where
traction or stability is doubtful.
• Test drive area with mower lowered but not running. Slow down when
you travel over rough ground.
Safety - 6
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
• Keep all movement on slopes slow and gradual. Do not make sudden
changes in speed or direction, which could cause the machine to roll over.
Protect Children
• Use extra care while operating machine with grasscatchers or other
attachments, they can affect stability of the machine. Do not use on steep
slopes.
• Do not mow near drop-offs, ditches, embankments, or bodies of water.
The machine could suddenly roll over if a wheel goes over the edge or the
edge caves in.
• Follow the manufacturer’s recommendations for wheel weights or
counterweights for added stability when operating on slopes or using front
or rear mounted attachments. Remove weights when not required.
• Drive machine very slowly and avoid quick stops when attachment is
removed.
• Transport machine with decks lowered to improve stability.
Use Seat Belt Properly
• Death or serious injury can occur when young children associate having
fun with a lawn mowing machine simply because someone has given
them a ride on a machine.
• Children are attracted to lawn mowing machines and mowing activities.
They don’t understand the dangers of rotating blades or the fact that the
operator is unaware of their presence.
• Children who have been given rides in the past may suddenly appear in
the mowing area for another ride and be run over or backed over by the
machine.
• Tragic accidents with children can occur if the operator is not alert to the
presence of children, especially when a child approaches a machine from
behind. Before and while backing up, stop mower blades and look down
and behind the machine carefully, especially for children.
• Never carry children on a machine or attachment, even with the blades
off. Do not tow children in a cart or trailer. They can fall off and be
seriously injured or interfere with safe machine operation.
• Use a seat belt when operating with the folding Roll-Over Protective
Structure (ROPS) in the upright position to minimize chance of injury from
an accident, such as an overturn.
• Never use the machine as a recreational vehicle or to entertain children.
• Never allow children or an untrained person operate the machine.
Instruct all operators not to give children a ride on the machine or in an
attachment.
• Do not use a seat belt when operating with the folding ROPS in the
folded position. Return the folding ROPS to the upright position as soon as
possible.
• Keep children indoors, out of the mowing area, and in the watchful eye
of a responsible adult, other than the operator, when a mower is being
operated.
• Never modify, disassemble or attempt to repair the seat belt.
• Replace entire seat belt if mounting hardware, buckle, belt, or retractor
show signs of damage.
• Stay alert to the presence of children. Never assume that children will
remain where you last saw them. Turn the machine off if a child enters the
work area.
• Inspect seat belt and mounting hardware at least once a year. Look for
signs of loose hardware or belt damage, such as cuts, fraying, extreme or
unusual wear, discoloration, or abrasion. Replace only with replacement
parts approved by your Great Dane.
Avoid Tipping
• Slopes are a major factor related to loss-of-control and tip-over
accidents, which can result in severe injury or death. Operation on all
slopes requires extra caution.
• Layers of heavy clothing can interfere with proper positioning of the seat
belt and can reduce the effectiveness of the seat belt.
Keep ROPS Installed Properly
• If you feel uneasy on a hillside, do not mow it.
• Mow across slopes, not up and down.
• Make certain all parts of the ROPS are installed correctly if the ROPS
structure is loosened or removed for any reason. All ROPS hardware
should be tightened to the proper torque per manufacturer’s
recommendations.
• Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven
terrain could overturn the machine. Tall grass can hide obstacles.
• Choose a low ground speed so you will not have to stop or shift while on
a slope.
• Any alteration of the ROPS must be approved by the manufacturer. The
protection provided by the ROPS will be impaired if the ROPS is subjected
to structural damage, is involved in an overturn incident, or is in any way
altered by welding, bending, drilling, or cutting.
• Do not mow or operate machine on wet grass. Tires may lose traction.
Tires may lose traction on slopes even though the brakes are functioning
properly.
• Never attempt to repair a damaged or altered ROPS. It must be
replaced to maintain the manufacturer’s certification of the structure.
• Avoid starting, stopping or turning on a slope. If the tires lose traction,
disengage the blades and proceed slowly, straight down the slope.
Safety - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
signals according to local regulations. Extra flashing warning lights may
need to be installed.
Keep Riders Off
• Only allow the operator on the machine. Keep riders off.
Checking Wheel Hardware
• Riders on the machine or attachment may be struck by foreign objects
or thrown off the machine causing serious injury.
• A serious accident could occur causing serious injury if wheel hardware
is not tight.
• Riders obstruct the operator’s view resulting in the machine being
operated in an unsafe manner.
• Check wheel hardware tightness often during the first 100 hours of
operation.
Avoid High Pressure Fluids
• Wheel hardware must be tightened to specified torque using the proper
procedure anytime it is loosened.
Wear Appropriate Clothing
• Hydraulic hoses and lines can fail due to physical damage, kinks, age,
and exposure. Check hoses and lines regularly. Replace damaged hoses
and lines.
• Hydraulic fluid connections can loosen due to physical damage and
vibration. Check connections regularly. Tighten loose connections.
• Always wear safety goggles, or safety glasses with side shields, and a
hard hat when operating the machine.
• Escaping fluid under pressure can penetrate the skin causing serious
injury. Avoid the hazard by relieving pressure before disconnecting
hydraulic or other lines. Tighten all connections before applying pressure.
• Wear close fitting clothing and safety equipment appropriate for the job.
• While mowing, always wear substantial footwear and long trousers. Do
not operate the equipment when barefoot or wearing open sandals.
• Search for leaks with a piece of cardboard. Protect hands and body from
high pressure fluids.
• Wear a suitable protective device such as earplugs. Loud noise can
cause impairment or loss of hearing.
• If an accident occurs, see a doctor immediately. Any fluid injected into
the skin must be surgically removed within a few hours or gangrene may
result. Doctors unfamiliar with this type of injury should reference a
knowledgeable medical source.
Maintenance and Storage
Driving Safely on Public Roads
• Never operate machine in a closed area where dangerous carbon
monoxide fumes can collect.
• Disengage drives, lower implement, lock parking brake, stop engine and
remove key or disconnect spark plug (for gas engines). Wait for all
movement to stop before adjusting, cleaning or repairing.
Avoid personal injury or death resulting from a collision with another
vehicle on public roads:
• Clean grass and debris from cutting units, drives, mufflers, and engine to
help prevent fires. Clean up oil or fuel spillage.
• Use safety lights and devices. Slow moving machines when driven on
public roads are hard to see, especially at night.
• Let engine cool before storing and do not store near flame.
• Whenever driving on public roads, use flashing warning lights and turn
Safety - 8
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
• Shut off fuel while storing or transporting. Do not store fuel near flames
or drain indoors.
• Do not store machine near an open flame or source of ignition, such as
a water heater or furnace.
• Park machine on level ground. Never allow untrained personnel to
service machine. Understand service procedure before doing work.
• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.
Replace if necessary.
• Use jack stands or lock service latches to support components when
required. Securely support any machine elements that must be raised for
service work.
Tire Safety
• Before servicing machine or attachment, carefully release pressure from
any components with stored energy, such as hydraulic components or
springs.
• Release hydraulic pressure by lowering attachment or cutting units to
the ground or to a mechanical stop and move hydraulic control levers back
and forth.
• Disconnect battery or remove spark plug (for gas engines) before
making any repairs. Disconnect the negative terminal first and the positive
last. Reconnect positive first and negative last.
• Use care when checking blades. Wrap the blades or wear gloves, and
use caution when servicing them. Only replace blades. Never straighten
or weld them.
• Keep hands, feet, clothing, jewelry and long hair away from moving
parts. If possible, do not make adjustments with the engine running.
Explosive separation of a tire and rim parts can cause serious injury or
death:
• Charge batteries in an open well ventilated area, away from spark and
flames. Unplug charger before connecting or disconnecting from battery.
Wear protective clothing and use insulated tools.
• Do not attempt to mount a tire without the proper equipment and
experience to perform the job.
• Keep all parts in good working condition and all hardware tightened.
Replace all worn or damaged decals.
• Always maintain the correct tire pressure. Do not inflate the tires above
the recommended pressure. Never weld or heat a wheel and tire
assembly. The heat can cause an increase in air pressure resulting in a
tire explosion. Welding can structurally weaken or deform the wheel.
• Check grasscatcher components and the discharge guard frequently
and replace with manufacturer’s recommended parts, when necessary.
Grasscatcher components are subject to wear, damage, and deterioration
which could expose moving parts or allow objects to be thrown.
• When inflating tires, use a clip-on chuck and extension hose long
enough to allow you to stand to one side and NOT in front of or over the
tire assembly.
• Keep all nuts and bolts tight, especially blade attachment bolts, to be
sure the equipment is in safe working condition.
• Check tires for low pressure, cuts, bubbles, damaged rims or missing
lug bolts and nuts.
• Check brake operation frequently. Adjust and service as required.
• On multi-bladed machines, take care as rotating one blade can cause
other blades to rotate.
Handling Fuel Safely
To avoid personal injury or property damage, use extreme care in
handling fuel. Fuel is extremely flammable and fuel vapors are
explosive:
Prevent Fires
• Remove grass and debris from engine compartment and muffler area,
before and after operating machine, especially after mowing or mulching
in dry conditions.
• Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
• Use only an approved fuel container. Use only non-metal, portable fuel
containers approved by the Underwriter’s Laboratory (U.L.) or the
American Society for Testing & Materials (ASTM). If using a funnel, make
sure it is plastic and has no screen or filter.
• Empty the grasscatcher completely before storing.
• Always shut off fuel when storing or transporting machine, if the
machine has a fuel shutoff.
Safety - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
• Never remove the fuel tank cap or add fuel with the engine running.
Allow engine to cool before refueling.
Handling Waste Product and Chemicals
• Never add fuel to or drain fuel from the machine indoors. Move machine
outdoors and provide adequate ventilation.
• Clean up spilled fuel immediately. If fuel is spilled on clothing, change
clothing immediately. If fuel is spilled near machine, do not attempt to start
the engine but move the machine away from the area of spillage. Avoid
creating any source of ignition until fuel vapors have dissipated.
• Never store the machine or fuel container where there is an open flame,
spark, or pilot light such as on a water heater or other appliance.
Waste products, such as, used oil, fuel, coolant, brake fluid, and batteries,
can harm the environment and people:
• Do not use beverage containers for waste fluids - someone may drink
from them.
• See your local Recycling Center or authorized dealer to learn how to
recycle or get rid of waste products.
• A Material Safety Data Sheet (MSDS) provides specific details on
chemical products: physical and health hazards, safety procedures, and
emergency response techniques. The seller of the chemical products
used with your machine is responsible for providing the MSDS for that
product.
• Prevent fire and explosion caused by static electric discharge. Static
electric discharge can ignite fuel vapors in an ungrounded fuel container.
Operating
• Never fill containers inside a vehicle or on a truck or trailer bed with a
plastic liner. Always place containers on the ground away from your
vehicle before fueling.
Daily Operating Checklist
oMake sure all necessary guards and shields are safely and securely
• Remove fuel-powered equipment from the truck or trailer and refuel it on
the ground. If this is not possible, then refuel such equipment with a
portable container, rather than from a fuel dispenser nozzle.
attached. Check for loose, missing, or damaged parts.
oRemove mower deck belt shields. Clean grass and debris from belt
area.
• Keep the nozzle in contact with the rim of the fuel tank or container
opening at all times until the fueling is complete. Do not use a nozzle lock-
open device.
oRemove grass and debris from machine and mower deck.
oTest park brake.
oTest safety systems.
oInspect battery terminals and hold-downs.
oInspect for oil leaks.
• Never overfill fuel tank. Replace fuel tank cap and tighten securely.
• Replace all fuel container caps securely after use.
• For gasoline engines, do not use gas with methanol. Methanol is
harmful to your health and to the environment.
oCheck engine and hydraulic oil levels.
oInspect all belts for damage or cracking.
oInspect engine air filter.
oInspect mower level.
oAdjust cutting height if necessary.
oInspect wheel bolt torque. Tighten if necessary.
oCheck tire air pressure. Check tires for damage or cracking.
oInspect front caster spindles/wheels.
Avoid Damage to Plastic and Painted Surfaces
• Do not wipe plastic parts unless rinsed first.
• Insect repellent spray may damage plastic and painted surfaces. Do not
spray insect repellent near machine.
Operating - 10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
• Be careful not to spill fuel on machine. Fuel may damage surface. Wipe
up spilled fuel immediately.
Mounting and Dismounting Machine Safely
• Prolonged exposure to sunlight will damage the hood surface.
Operator Station Controls
Do not step on the mower deck when mounting and dismounting the
machine. Mount the machine from the front using the foot plate (A). Park
machine safely (See Parking Safely in the SAFETY section) before
dismounting.
A- Motion Control Levers
B- Park Brake Lever
Keep the foot plate clean.
C- Seat Adjustment Lever
D- Hourmeter
Raising and Lowering Operator Seat
E- Ignition Key Switch
F- PTO Knob
CAUTION: Avoid injury! The seat is heavy and can cause
injury if it falls. When performing any service function under
the operator seat, make sure the seat is tilted forward and
rests against the hinge stops.
G- Choke (Carbureted Engines Only)
H- Throttle Lever
I - Mower Deck Lift/Lower Lever
J - Height-of-Cut (HOC) Adjustment Pin
K- Mower Deck Transport Position Lock Lever
Raising the Seat:
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Slide seat to full rear position.
Miscellaneous Controls
3.Remove two locknuts (A) and capscrews securing the flanges at the
rear of the seat frame (B) to the machine.
A- Hydraulic Pump Free-Wheel Valves
4.Lift seat frame and tilt forward until it rests against the hinge stops.
Lowering the Seat:
1.Stand on the side of the machine.
2.Slowly lower seat frame. Secure with cap screws and locknuts, removed
earlier.
3.Adjust seat as necessary for operator comfort.
Operating - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
Adjusting Seat
Using Seat Belt
Front-to-Back Adjustment
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Sit on the operator seat.
CAUTION: Avoid injury! Always wear seat belt when
operating machine with non-folding Roll-Over Protective
Structure (ROPS) or folding ROPS in upright position. Do not
jump from machine if machine tips.
CAUTION: Avoid injury! Never adjust seat while machine is
moving. Stop machine before adjusting seat to prevent loss of
machine control.
•If folding ROPS must be folded to operate in a low
clearance area, do not use seat belt. Raise ROPS and use
seat belt as soon as conditions permit.
1.Sit in seat.
3.To adjust the seat front to back, push and hold the seat adjustment lever
(A) away from the seat.
2.Pull belts across your lap and insert seat belt buckle (A) into latch (B)
until it locks.
4.Slide forward or backward to desired position.
5.Release lever.
3.To release seat belt, press red button (C) until buckle comes out of latch.
Seat Height Adjustment
Raising and Lowering ROPS
Raising ROPS
1.Sit on the operator seat.
2.To lower the seat, turn knob (B) counterclockwise.
3.To raise the seat, turn knob (B) clockwise.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Remove spring pin (A) from drilled pin (B) on left and right side of ROPS.
3.Remove drilled pin from left and right side of ROPS.
Operating - 12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Move the mower deck lift lever (A) to the transport position (D).
3.Position the HOC adjustment pin (C) in the proper hole for the desired
height-of-cut.
4.Push ROPS into upright position.
4.Pull back and hold the mower deck lift lever (A) and release the
transport position lock lever (B).
5.Install drilled pin (B) into holes on left and right side of ROPS, and
secure in place with spring pins (A).
6.Check the ROPS bolt torque if the ROPS is loose.
Lowering ROPS
CAUTION: Avoid injury! Use roll-over protection system
(ROPS) in lowered position only when low clearance
operation is necessary.
•Do not use seat belt when ROPS is in lowered position.
•Do not operate machine on slope with ROPS in folded
position.
•Raise ROPS and fasten seat belt as soon as conditions
permit.
5.Allow the mower deck lift lever (A) to rest against the HOC adjustment
pin (C).
1.Park machine safely. (See Parking Safely in the SAFETY section).
2.Remove spring pin (A) from drilled pin (B) on left and right side of ROPS.
3.Remove drilled pin from left and right side of ROPS.
4.Pull ROPS rearward to lower.
Adjusting Mower Deck Anti-Scalp Wheels
1.Park machine safely. (See Parking Safely in the SAFETY section.)
5.Install drilled pins and spring pins back into hole in ROPS to secure in
place.
CAUTION: Avoid injury! Fingers and loose clothing can get
caught in rotating parts. Do not operate machine without all
mower deck belt shields installed.
Adjusting Mower Deck Cutting Height
NOTE: The flattest cut can be achieved by having all anti-scalp
wheels adjusted off the ground. Check anti-scalp wheel adjustments
each time the mower deck cutting height is changed.
CAUTION: Avoid injury! Rotating blades are dangerous and
can cut fingers and toes. Stop engine, lock the park brake,
and wait for blade to stop rotating before adjusting cutting
height.
It is recommended that all anti-scalp wheels be kept off the ground to
minimize scuffing.
Cutting height can be adjusted from approximately 25-125 mm (1-5 in.).
Each hole adjusts the height-of-cut (HOC) in approximately 12 mm (1/2
in.) increments.
2.Inflate tires to correct pressure.
3.Adjust mower deck to desired cutting height.
The deck can also be raised and locked in a transport position, to provide
maximum ground clearance when moving the machine from one area to
another.
Operating - 13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
NOTE: The rear anti-scalp wheels are located under the rear of the
mower deck.
Testing Safety Systems
CAUTION: Avoid injury! Engine exhaust fumes contain
carbon monoxide and can cause serious illness or death.
Move the machine to an outside area before running the
engine.Do not run an engine in an enclosed area without
adequate ventilation.•
•Connect a pipe extension to the engine exhaust pipe to
direct the exhaust fumes out of the area.
•Allow fresh outside air into the work area to clear the
exhaust fumes out.
The safety systems installed on your machine should be checked before
each machine use. Be sure you have read the machine operator manual
and are completely familiar with the operation of the machine before
performing these safety system checks.
Use the following checkout procedures to check for normal operation of
machine.
4.Adjust anti-scalp wheel (A) to one of two positions (B).
• Remove screw (C), nut and washer.
If there is a malfunction during one of these procedures, do not operate
machine. See your authorized dealer for service.
• Adjust wheel up or down so it is approximately 6-13 mm (1/4-1/2 in.)
above mowing surface.
Perform these tests in a clear open area. Keep bystanders away.
Testing PTO Switch
5.Install wheel with attaching hardware.
6.Adjust all wheels to same height.
1.Sit on the operator seat with the motion control levers in the neutral
detent position (standard levers) or neutral lock position (optional “over the
lap” levers).
Testing Safety Systems
2.Lock the park brake.
3.Pull PTO knob up to engage.
4.Turn key switch to the start position.
Result: The engine must not crank.
CAUTION: Avoid injury! Engine exhaust fumes contain
carbon monoxide and can cause serious illness or death.
Move the machine to an outside area before running the
engine.Do not run an engine in an enclosed area without
adequate ventilation.•
Testing Park Brake Switch
•Connect a pipe extension to the engine exhaust pipe to
direct the exhaust fumes out of the area.
1.Sit on the operator seat with the motion control levers in the neutral
detent position (standard levers) or neutral lock position (optional “over the
lap” levers).
•Allow fresh outside air into the work area to clear the
exhaust fumes out.
2.Push PTO knob down to disengage.
3.Unlock the park brake.
The safety systems installed on your machine should be checked before
each machine use. Be sure you have read the machine operator manual
and are completely familiar with the operation of the machine before
performing these safety system checks.
4.Turn key switch to the start position.
Result: The engine must not crank.
Use the following checkout procedures to check for normal operation of
machine.
Testing Neutral Start Switch
NOTE: Repeat this test three times, with the motion control levers in
the following positions:
If there is a malfunction during one of these procedures, do not operate
machine. See your authorized dealer for service.
Perform these tests in a clear open area. Keep bystanders away.
• Right side motion control lever inward.
• Left side motion control lever inward.
• Both motion control levers inward.
1.Move motion control lever(s) out of the neutral detent position (standard
levers) or neutral lock position (optional “over the lap” levers).
2.Lock the park brake.
3.Push PTO knob down to disengage.
4.Turn key switch to the start position.
Result: The engine must not crank.
Operating - 14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
Locking Park Brake:
Testing Seat Switch
Procedure 1:
1.Sit on the operator seat with the motion control levers in the neutral
detent position (standard levers) or neutral lock position (optional “over the
lap” levers).
CAUTION: Avoid injury! If the engine should stop while
operating on an incline, the mower can free wheel. If this
should occur:•lock the park brake,
2.Unlock the park brake.
•start the engine,
3.Push PTO knob down to disengage.
4.Turn key switch to the start position.
5.Raise slightly off the seat.
•unlock the park brake,
•resume operation.
Result: The engine must stop.
Procedure 2:
1.Start engine.
2.Lock the park brake.
3.Pull PTO knob up to engage.
4.Raise slightly off the seat.
Result: The engine must stop.
Testing the Park Brake
• Raise and pull rearward park brake lever (A) to lock the park brake.
Unlocking Park Brake:
1.Stop machine on a 17° slope (30% grade). Stop the engine and lock the
park brake.
Result: Park brake must hold the machine stationary. (Machine should
move no more that 61 cm (24 in.) in one hour.) If machine moves more
than that, brakes need to be adjusted. See Adjusting Park Brake in the
Service Steering & Brakes section.
• Lower park brake lever (A) forward to unlock the park brake.
Using the Park Brake
CAUTION: Avoid injury! Children or bystanders may attempt
to move or operate an unattended machine.
Always lock the park brake and remove the key before leaving
the machine unattended.
Operating - 15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
Using the Key Switch
Using the Throttle Lever
NOTE: Machine will only start if the following conditions exist:
• Park brake is locked.
• PTO is disengaged.
• Motion control levers are in the neutral detent position (standard
levers) or neutral lock position (optional “over the lap” levers).
A
B
STOP
• Push throttle lever (A) all the way forward to the full-throttle detent
position (B) when mowing.
C
• Move throttle lever (A) to the 1/2-throttle position (C) when starting and
warming the engine.
• Pull throttle lever (A) rearward to the slow position (D) to idle engine. Do
not run engine at slow idle any longer than necessary.
• To turn ignition off, turn key to the STOP position (A).
• To turn ignition on, turn key to the run position (B).
Using the Hourmeter
NOTE: The machine is equipped with an electric start. The hourmeter
will continue to run with the key switch left in the run position.
• To start engine, turn key to the start position (C). Once engine begins to
run, release key back to the run position.
Using the PTO
Engage PTO:
• The hourmeter (A) shows the number of hours the machine has run.
• The service interval chart gives necessary service intervals. Use the
hourmeter and service interval chart in the Service Intervals section to
determine when machine will need service.
1.Move throttle lever (A) to the 1/2- to 3/4-throttle position.
2.Pull PTO knob (B) up to engage mower deck.
See the service interval chart in the engine manufacturer’s owners manual
supplied with your machine to determine when the engine will need
service.
3.Move throttle lever (A) forward to the fast detent position (C) for mowing.
Disengage PTO:
• Push PTO knob (B) down.
Operating - 16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
switch disengaged and the park brake locked to start the engine.
Using the Choke
Engage Choke:
Neutral Lock Position - Optional “Over the Lap” Levers
• Pull choke knob (A) out.
Disengage Choke:
Picture Note: Motion control levers (A) shown in the neutral lock
position.
• Push choke knob (A) in.
• Motion control levers must be in the neutral lock position, the PTO
switch disengaged and the park brake locked to start the engine.
Using the Motion Control Levers
• Forward and reverse movement of the motion control levers is
prevented when levers are moved to the neutral lock position.
CAUTION: Avoid injury! Learn use of the motion control
levers and practice at half throttle until becoming proficient
and comfortable with the operation of the machine.
• Operator can exit mower with the engine running when the PTO switch
is disengaged, the motion control levers are in the neutral lock position
and the park brake is locked.
Do not move motion control levers from forward to reverse or
reverse to forward position rapidly. Sudden direction changes
could cause loss of control or damage the machine.
• Motion control levers must be in the neutral lock position to safely enter
and exit the operator seat.
Neutral Position - Optional “Over the Lap” Levers
NOTE: Two types of control levers are available - standard “center
steer” levers and optional “over the lap” levers. The operation of
both styles of levers is the same except as noted.
The functions of the motion control levers are:
• Dual function neutral position.
• Steering.
• Acceleration.
• Braking.
Neutral Detent Position - Standard “Center Steer” Levers
NOTE: When the control levers are in the neutral detent position, the
control lever rollers (A) located on each side of the control console
will be seated in the notches in the console.
Picture Note: Motion control levers (A) shown in the neutral
position.
• Machine speed, motion, and direction can be controlled when the
engine is running, operator is on the seat and the park brake is unlocked.
• Motion control levers must be in the neutral detent position, the PTO
Operating - 17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
Forward and Reverse Motion:
Reverse:
CAUTION: Avoid injury! Children or bystanders can be
injured or killed by moving machine and rotating blades.
Before traveling forward or rearward:•
•Carefully check area around machine.
•Disengage mower before backing up.
1.Move throttle lever to the full-throttle position.
2.Unlock the park brake.
3.Optional “over the lap” levers: Move both motion control levers from the
neutral lock position inward to the neutral position.
4.Push the control levers forward to begin forward motion.
• The farther forward the control levers are moved, the faster the
machine will travel.
• Pull both control levers past center rearward at the same time.
Gentle Left Turn:
• Forward speed range: 0-14 km/h (0-9 mph).
5.Pull both control levers rearward at the same time to begin reverse
motion.
• Reverse speed range: 0-6 km/h (0-4 mph).
6.To stop motion, move both motion control levers forward or rearward
until the machine comes to a stop.
NOTE: The motion control linkages are adjustable. If adjustment is
required, see Checking and Adjusting Motion Control Linkages in
the Service Transmission section.
Forward:
• Push right control lever farther forward than the left control lever.
Gentle Right Turn:
• Push both motion control levers forward at the same time.
• Push left control lever farther forward than the right control lever.
Operating - 18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
Sharp Left Turn:
4.Push PTO knob (A) down to disengage PTO.
5.Move throttle lever to set engine speed:
• Push right control lever forward and pull left control lever rearward at the
same time.
• Cold engine: Set throttle lever at the 1/2- to 3/4-throttle position.
• Warm/Hot engine: Set throttle lever to the 1/2-throttle position.
6.Position choke knob (D):
Sharp Right Turn:
• Cold engine: Pull knob up and hold in choke position.
• Warm/Hot engine: If necessary, pull knob up and hold in choke
position.
IMPORTANT: Avoid damage! Starter may be damaged if starter is
operated for more than 20 seconds at a time:
• Wait two minutes before trying again if engine does not start.
STOP
C
• Push left control lever forward and pull right control lever rearward at the
same time.
Starting the Engine
B
CAUTION: Avoid injury! Engine exhaust fumes contain
carbon monoxide and can cause serious illness or death.
Move the machine to an outside area before running the
engine.Do not run an engine in an enclosed area without
adequate ventilation.
7.Turn key switch to start position (B).
If the engine does not start, wait 10 seconds.
• Turn key to start position again for no more than 5 seconds.
• Repeat the procedure if necessary.
•Connect a pipe extension to the engine exhaust pipe to
direct the exhaust fumes out of the area.
•Allow fresh outside air into the work area to clear the
exhaust fumes out.
IMPORTANT: Avoid damage! Unnecessary engine idling can
cause engine overheating, carbon build-up, and poor
performance.
1.Sit on the operator seat.
2.Lock the park brake.
8.Release key to run position (C) when engine starts.
9.With engine started:
3.Move both motion control levers to the neutral detent position (standard
levers) or neutral lock position (optional “over the lap” levers).
• Push choke knob to off position.
• Move throttle lever to full-throttle position.
• Unlock the park brake.
Operating - 19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
move throttle to slow position.
Engaging Mower
CAUTION: Avoid injury! Clear mowing area of all bystanders
when operating this machine.
A
STOP
Thrown objects could cause serious injury or death.
Keep hands and feet away from blades and discharge
opening.
Do not mow in reverse unless absolutely necessary.
IMPORTANT: Avoid damage! To help prevent damage to PTO
clutch:
• Do not engage PTO with throttle in the fast position.
1.Adjust mower deck to desired cutting height.
2.Start engine.
5.Turn key switch to STOP position (A).
CAUTION: Avoid injury! Children or bystanders may attempt
to move or operate an unattended machine.
Always lock the park brake and remove the key before leaving
the machine unattended.
6.Remove key.
Transporting Machine
CAUTION: Avoid injury! Use extra care when loading or
unloading the machine into a trailer or truck.
Close fuel shut-off valve, if your machine is equipped.
3.Move throttle lever to the 1/2 - 3/4 throttle position.
4.Unlock the park brake.
IMPORTANT: Avoid damage! Transmission damage may occur if
the machine is moved or towed incorrectly:
5.Move both motion control levers to the neutral position.
• Move unit by hand only.
NOTE: In cold weather or with a new machine, it may be necessary to
engage the choke at the same time as the PTO knob to prevent the
engine from stalling.
• Do not use another vehicle to move unit.
• Do not tow unit.
6.Pull PTO knob (A) up to engage mower deck.
7.Move throttle lever to full-throttle position.
Use a heavy-duty trailer to transport your machine. Trailer must have
signs and lights required by law.
1.Raise the mower deck lift lever to the transport position.
2.Drive machine on trailer.
NOTE: The travel speed and turn rate will vary with the amount that
the control levers are moved.
8.Push motion control levers forward slowly. Mow at a safe travel speed.
3.Stop engine and lock the park brake.
4.Remove key.
Stopping the Engine
5.Fasten machine to trailer with heavy-duty straps, chains or cables. Both
front and rear straps must be directed down and outward from machine.
IMPORTANT: Avoid damage! To help prevent engine backfiring,
throttle lever should be set at the 1/4 throttle position and run for
30 seconds prior to stopping the engine.
Mowing Tips
Do not stop engine when mower is on a slope of more than 30° for
an extended period of time. Oil may run through valve train into
carburetor and muffler.
• Mow grass with throttle lever in the full fast position.
• Cut grass when it is dry.
• Keep mower deck and discharge chute clean.
• Mow with sharp blades.
1.Move the motion control levers to the neutral detent position (standard
levers) or neutral lock position (optional “over the lap” levers).
• Properly level mower deck for a smooth cut.
• Mow grass high and often.
2.Lock the park brake.
3.Push PTO switch down to disengage.
• Use a travel speed that fits the conditions:
4.Move throttle lever to 1/4-throttle position and run for 30 seconds, then
Operating - 20
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE INTERVALS
• Mow tall or wet grass twice. Cut grass at half desired height – then cut
• Check wheel nut torque.
at desired height.
• Check and adjust (as needed) park brake.
• Remove debris from the underside of the mower deck.
• Travel slow when mowing tall, thick or wet grass.
• Avoid damaging grass by slipping or skidding machine drive wheels.
Practice smooth control lever movements.
Every 25 Hours or Weekly (Whichever Comes First)
• Grease mower deck thrust arms (two places).
• Grease mower deck thrust arms (two places).
• Grease spindle bearings (three places).
• When performing sharp turns, do not allow inside machine drive wheel
to stop and twist on grass.
Mowing Travel Speeds
Use slow travel speed for:
• Trimming.
• Grease traction drive belt tension arm.
• Grease mower deck drive belt tension arm.
• Grease HOC shafts (four places).
• Working in close quarters.
• Mowing tall grass.
• Lubricate front caster wheel spindles.
Use faster travel speeds for:
• Normal mowing on level ground.
• Remove debris from the underside of the mower deck.
Every 50 Hours or Weekly (Whichever Comes First)
Dismounting to Inspect Mower
• Change engine oil and filter. See the engine manufacturer’s owner’s
manual provided with your machine for the complete procedure.
• Grease caster wheel spindle bearings (two places).
• Grease mower deck thrust arms (two places).
• Remove debris from the underside of the mower deck.
• Check drive belt tension.
CAUTION: Avoid injury! Help prevent serious injury. Keep
hands and feet away from blades and the discharge opening.
Do not step on either side of the mower deck when mounting
and dismounting the machine. Mount and dismount the
machine using the front foot plate.
• Check tire pressure.
1.Park machine on a hard, level surface.
• Clean engine air filter.
2.Push PTO knob down to disengage mower.
• Check wheel nut torque.
3.Move motion control levers to the neutral detent position (standard
levers) or neutral lock position (optional “over the lap” levers).
Every 160 Hours or Monthly (Whichever Comes First)
• Check transmission oil level.
4.Lock the park brake.
5.Stop engine and remove key. Always wait for mower blades to stop
turning before leaving operator seat.
• Check transmission oil level.
• Lubricate mower deck idler pulley pivots (three places).
• Lubricate seat platform hinges (two places)
• Lubricate pump control arms (five places).
• Lubricate control lever pivot shafts (two places).
• Lubricate throttle cable.
Service Intervals
Servicing Your Machine
IMPORTANT: Avoid damage! Operating in extreme conditions
may require more frequent service intervals:
• Lubricate choke control cable.
• Engine components may become dirty or plugged when
operating in extreme heat, dust or other severe conditions.
Annually
• Inspect all spindle bearings (6). Replace as needed.
• Inspect all mower deck idler pulleys (3). Replace as needed.
• Engine oil may lose efficiency if vehicle is operated constantly
at slow or low engine speeds or with frequent short trips.
• Remove and inspect caster wheel roller bearings; clean and pack with
grease. Replace as needed.
Please use the following timetables to perform routine maintenance on
your machine.
• Remove and inspect caster pivot bearings; clean and pack with grease.
Replace as needed.
Break-In (After First 8 Hours of Operation)
• Inspect drive belts. Replace as needed. Run-in and adjust tension.
NOTE: The following initial break-in items must be performed and
verified to validate the warranty (dealer service invoice accepted).
• Change hydraulic oil and filter (annually or 500 hours whichever comes
first).
• Change engine oil and filter.
• Check all bolts and nuts; tighten as needed.
• Remove battery. Clean battery and holder.
• Replace spark plugs.
• Check drive belt tension.
• Check mower deck drive belt tension.
• Check transmission neutral adjustment.
Service Intervals - 21
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE LUBRICATION
Service Lubrication
Grease
IMPORTANT: Avoid damage! The recommended grease is
effective within an average air temperature range of -29 to 135
degrees C (-20 to 275 degrees F).
If operating outside that temperature range, contact your
servicing dealer for a special-use grease.
Use a general all-purpose grease with an NLGI grade No.2 rating.
Wet or high speed conditions may require use of a special-use grease.
Contact your Servicing dealer for information.
Spray Lubricant
3.Grease HOC shafts (C) (two points on each side of the machine).
Use a general-purpose petroleum-based spray lubricant.
Lubrication Points
CAUTION: Avoid injury! Rotating parts can catch fingers,
loose clothing, or long hair. Wait for engine and all moving
parts to stop before leaving operator’s station to adjust or
service machine.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
4.Grease mower deck thrust arms (D), located at the rear of the mower
deck.
2.Grease caster wheel spindle bearings (B).
5.Apply grease to three spindle bearings.
Service Lubrication - 22
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE ENGINE
9.Lubricate hydraulic pump control arms (N).
6.Grease traction drive belt tension arm pivot (G).
10.Lubricate control lever pivot shaft (O).
11.Lubricate seat platform hinges (P).
12.Lubricate throttle control cable (Q).
13.Lubricate choke control cable (R).
Service Engine
Engine Warranty Maintenance Statement
Maintenance, repair, or replacement of the emission control devices and
systems on this engine, which are being done at the customer’s expense,
may be performed by any non-road engine repair establishment or
individual. Warranty repairs must be performed by an authorized servicing
dealer.
7.Grease mower deck drive belt tension arm (H).
Avoid Fumes
NOTE: Use spray lubricant to lubricate the following items:
CAUTION: Avoid injury! Engine exhaust fumes contain
carbon monoxide and can cause serious illness or death.
Move the machine to an outside area before running the
engine.Do not run an engine in an enclosed area without
adequate ventilation.•
•Connect a pipe extension to the engine exhaust pipe to
direct the exhaust fumes out of the area.
•Allow fresh outside air into the work area to clear the
exhaust fumes out.
Engine Oil
Use oil viscosity based on the expected air temperature range during the
period between oil changes.
8.Lubricate mower deck idler pulleys (K-M).
Use oil that meets the following specification:
• See the engine manufacturer’s owner’s manual provided with your
machine for the correct specifications.
Service Engine - 23
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE ENGINE
Checking Engine Oil Level
CAUTION: Avoid injury! Touching hot surfaces can burn
skin. The engine, components, and fluids will be hot if the
engine has been running. Allow the engine to cool before
servicing or working near the engine and components.
IMPORTANT: Avoid damage! Failure to check the oil level
regularly could lead to serious engine problems if oil level is low:
• Check oil level before operating.
• Keep oil level between the FULL and the ADD marks.
• Check oil level when engine is stopped, level, and is cooled so
oil has had time to drain into the sump.
3.Put container under drain tube.
NOTE: Check oil twice a day if you run engine over 4 hours in a day.
Make sure engine is cool when checking engine oil level.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Allow engine to cool.
4.Open drain valve (A) using a 10 mm socket, 1 ft extension, swivel and 3/
8 in. drive ratchet.
5.Allow oil to drain into an oil drain pan.
6.After oil drains, close drain valve.
7.Remove oil filter using an appropriate filter wrench. Turn filter
counterclockwise to remove.
IMPORTANT: Avoid damage! Dirt and debris in oil may cause
damage to the engine. Clean area around opening before
removing plug or dipstick.
8.Apply a film of clean engine oil on gasket of new filter.
9.Install filter. Turn filter clockwise until gasket makes contact with
mounting surface. Tighten 1/2 to 3/4 turn after gasket contact.
3.Remove dipstick (A). Wipe with a clean cloth.
4.Install dipstick and allow the cap to rest on the end of the tube. Do not
tighten the cap.
10.Clean area around the dipstick.
11.Unscrew and remove dipstick.
IMPORTANT: Avoid damage! To prevent extensive engine wear or
damage, always maintain the proper engine oil level. Never
operate the engine with the oil level below the add mark or over
the full mark.
IMPORTANT: Avoid damage! To prevent extensive engine wear or
damage, always maintain the proper engine oil level. Never
operate the engine with the oil level below the add mark or over
the full mark.
5.Remove dipstick and check oil level on dipstick. Oil must be between the
ADD and FULL marks.
12.Add approximately 1.4 L (1.5 qt) of oil.
13.Install and tighten dipstick.
• If oil is low, add oil to bring oil level no higher than the FULL mark on
dipstick.
14.Start engine and run at slow throttle for approximately two minutes.
Check for leaks around filter and drain valve.
• If oil level is above the FULL mark, drain to proper level.
6.Install and tighten dipstick.
15.Stop engine.
16.Check oil level:
Changing Engine Oil and Filter
• Remove dipstick. Wipe with a clean cloth.
• Install dipstick and allow the cap to rest on the end of the tube. Do not
tighten the cap.
IMPORTANT: Avoid damage! Change the oil more often if the
vehicle is used in extreme conditions:
• Remove dipstick and check oil level on dipstick. Oil level should be
between the ADD and FULL marks. Add oil if needed.
• Extremely dusty conditions.
• Frequent slow or low-speed operation.
• Frequent short trips.
17.Install and tighten dipstick.
1.Run engine to warm oil.
MODEL
Oil Capacity With Filter (Dry)
1.8 L (1.9 qt)
2.Park machine safely. (See Parking Safely in the SAFETY section).
Kawasaki Engines
Kohler Engines
2.0 L (2.1 qt)
Service Engine - 24
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE ENGINE
your machine for the complete procedure.
Cleaning Engine Air Intake Screen and Fan
Adjusting Carburetor
CAUTION: Avoid injury! Compressed air can cause debris to
fly a long distance.•
NOTE: Carburetor is calibrated by the engine manufacturer and is
not adjustable.
•Clear work area of bystanders.
If engine is operated at altitudes above 1829 m (6,000 ft), some
carburetors may require a special high altitude main jet. See your
authorized dealer.
•Wear eye protection when using compressed air for
cleaning purposes.
If engine is hard to start or runs rough, check the TROUBLESHOOTING
section of this manual.
•Reduce compressed air pressure to 210 kPa (30 psi).
Possible engine surging will occur at high throttle with transmission in “N”
neutral and mower engagement lever disengaged. This is a normal
condition due to the emission control system.
IMPORTANT: Avoid damage! An obstructed air intake screen can
cause engine damage due to overheating. Keep air intake screen
and other external surfaces of the engine, including cooling fins,
clean at all times to allow adequate air intake.
After performing the checks in the troubleshooting section and your
engine is still not performing correctly, contact your authorized dealer.
Keep air intake screens and engine cooling fins clear of debris to ensure
proper cooling. See the engine manufacturer’s owner’s manual provided
with your machine for the complete procedure.
Replacing Fuel Filter
CAUTION: Avoid injury! Fuel vapors are explosive and
flammable:•Do not smoke while handling fuel.
Checking and Cleaning Air Filter Elements
•Keep fuel away from flames or sparks.
•Shut off engine before servicing.
•Cool engine before servicing.
CAUTION: Avoid injury! Touching hot surfaces can burn
skin. The engine, components, and fluids will be hot if the
engine has been running. Allow the engine to cool before
servicing or working near the engine and components.
•Work in a well-ventilated area.
•Clean up spilled fuel immediately.
IMPORTANT: Avoid damage! Dirt and debris can enter the engine
through a damaged filter element:
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Allow engine to cool.
• Do not wash paper element.
• Do not attempt to clean paper element by tapping against
another object.
3.Place a drain pan under hoses to catch any fuel that may be left in
hoses.
• Do not use pressurized air to clean element.
• Replace element only if it is very dirty, damaged or the seal is
cracked.
NOTE: It may be necessary to check the air filter more frequently if
operating machine in dusty conditions.
Check and clean air filter elements at the intervals recommended in the
Service Intervals section. See the engine manufacturer’s owner’s manual
provided with your machine for the complete procedure.
Cleaning Engine Oil Cooler - Kohler Engines
Keep engine oil cooler fins clear of debris to ensure proper cooling. See
the engine manufacturer’s owner’s manual provided with your machine for
the complete procedure.
Checking Spark Plug
Picture Note: Kawasaki engine shown.
4.Locate fuel hose (A) coming from fuel tank, disconnect it from the inlet
side of fuel filter (B) and drain gasoline into a properly marked container.
CAUTION: Avoid injury! Touching hot surfaces can burn
skin. The engine, components, and fluids will be hot if the
engine has been running. Allow the engine to cool before
servicing or working near the engine and components.
5.Remove fuel filter from fuel hose (C) going to engine. Discard filter.
IMPORTANT: Avoid damage! When installing a new fuel filter, the
filter arrow must be pointing in the direction of fuel flow. Make
sure clamps are installed properly.
IMPORTANT: Avoid damage! Do not clean spark plugs with
abrasives.
6.Connect a new fuel filter to hoses. Make sure fuel filter is installed with
arrow pointing in direction of fuel flow.
Check spark plugs at the intervals recommended in the Service Intervals
section. See the engine manufacturer’s owner’s manual provided with
Service Engine - 25
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE TRANSMISSION
IMPORTANT: Avoid damage! Contamination of hydraulic fluid
could cause transmission damage or failure. Do not open oil
reservoir cap unless absolutely necessary.
Service Transmission
Hydraulic Oil
Severe or unusual conditions may require a more frequent
service interval.
Use only 5W-50 or 15W-50 all synthetic oil.
Checking Hydraulic Oil Level
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2. Allow engine and hydraulic oil reservoir to cool.
IMPORTANT: Avoid damage! Check oil level in reservoir tank
when oil is cold.
3.Clean area around reservoir filler cap, and remove filler cap from
reservoir.
Do not overfill oil reservoir tank. Oil will expand during operation
and could overflow.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
IMPORTANT: Avoid damage! Dirt and debris in oil may cause
damage to the transaxle. Clean area around opening before
removing dipstick.
4.Remove cap (A) from oil reservoir tank filler neck.
2.Unscrew and remove hydraulic reservoir cap/dipstick (A) from hydraulic
oil reservoir.
3.Wipe dipstick with a clean cloth.
4.Install dipstick and allow the cap to rest on the end of the tube. Do not
tighten the cap.
5.Remove dipstick and check oil level. Oil level should be at top mark on
dipstick.
6.If necessary, add oil through oil reservoir filler neck.
7.Install cap on filler neck.
5.Turn hydraulic oil filter (B) counterclockwise to remove.
6.Allow hydraulic oil to drain into a drain pan with at least a 3.8 L (1.0 gal)
capacity.
Changing Hydraulic Oil and Filter
7.Apply a film of clean oil on gasket of new filter.
8.Install filter. Turn filter clockwise until gasket makes contact with
mounting surface. Tighten 1/2 to 3/4 turn after gasket contact.
CAUTION: Avoid injury! Escaping fluid under pressure can
penetrate the skin causing serious injury. Avoid the hazard by
relieving pressure before disconnecting hydraulic or other
lines. Tighten all connections before applying pressure.
Search for leaks with a piece of cardboard. Protect hands and
body from high pressure fluids.
NOTE: Reservoir capacity is approximately 1.9 L (2.0 qt). Total
system capacity is approximately 3.5 L (3.75 qt).
9.Fill oil reservoir with approximately 1.9 L (2.0 qt) of oil.
10.Install reservoir cap.
Use caution when filling and draining hydraulic oil. During
periods of machine operation the hydraulic oil reservoir can
get hot. Allow engine and oil reservoir to cool before
servicing.
Service Transmission - 26
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE TRANSMISSION
Removing and Installing Traction Drive Belt
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Remove mower deck drive belt.
CAUTION: Avoid injury! Engine exhaust fumes contain
carbon monoxide and can cause serious illness or death.
Move the machine to an outside area before running the
engine.Do not run an engine in an enclosed area without
adequate ventilation.
CAUTION: Avoid injury! Fingers and hands can be pinched or
crushed. Keeps hands clear of sheave and belt pinch points
when servicing belt.
•Connect a pipe extension to the engine exhaust pipe to
direct the exhaust fumes out of the area.
•Allow fresh outside air into the work area to clear the
exhaust fumes out.
11.Start engine.
12.Move throttle lever to 3/4-throttle position.
13.Unlock the park brake.
CAUTION: Avoid injury! Help prevent serious bodily injury.
Remain alert to other people and the surroundings when
operating the machine.
14.Run engine in full forward position for several minutes and then cycle
motion control levers forward and rearward several times. Check for leaks
around filter.
15.Stop engine. Check oil level. Add oil as necessary.
Cleaning Hydraulic Pump Cooling Fins
Picture Note: Drive belt routing as viewed from top of machine.
A- 1/2 in. Square Opening
B- Tension Arm
CAUTION: Avoid injury! Compressed air can cause debris to
fly a long distance.
C- Traction Drive Belt
D- Engine Drive Sheave
•Clear work area of bystanders.
E- Tension Idler Sheave
•Wear eye protection when using compressed air for
cleaning purposes.
F- Hydraulic Pump Sheave
3.Using a 1/2 in. drive breaker bar and extension, insert end of extension
in 1/2 in. drive square opening (A) in tension arm, and carefully move
tension arm (B) counter-clockwise to release belt tension.
•Reduce compressed air pressure to 210 kPa (30 psi).
IMPORTANT: Avoid damage! To ensure proper cooling, keep the
cooling fins clean at all times. Operating the machine with
obstructed cooling fins could cause damage due to overheating.
4.Remove drive belt (C).
5.Install new drive belt.
6.Install mower deck drive belt as shown.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
Checking and Adjusting Motion Control Linkages
CAUTION: Avoid injury! Do not attempt this adjustment
unless you are a qualified and properly trained technician.
Improper adjustment can result in an unsafe machine.
2.Clean hydraulic oil cooler fins (A) on each hydraulic pump with a rag,
brush, or compressed air.
Service Transmission - 27
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE TRANSMISSION
Check Neutral Creep
CAUTION: Avoid injury! Engine exhaust fumes contain
carbon monoxide and can cause serious illness or death.
Move the machine to an outside area before running the
engine.
Do not run an engine in an enclosed area without adequate
ventilation.
•Connect a pipe extension to the engine exhaust pipe to
direct the exhaust fumes out of the area.
•Allow fresh outside air into the work area to clear the
exhaust fumes out.
NOTE: Check and adjust motion control linkages with the machine
parked on a hard, level surface.
7.Remove pin (C) and disconnect swivel (D) from each traction control rod
(E), and rotate the swivel.
1.Start engine.
8.Rotate swivel (D) to adjust:
2.Set throttle lever to full-throttle position.
3.Unlock the park brake.
• To stop forward creep, rotate each swivel (D) counterclockwise one
rotation.
• To stop rearward creep, rotate each swivel (D) clockwise one rotation.
9.Connect swivel to traction control rod.
10.Repeat as needed to stop machine creep.
11.Lower seat.
4.If the rear drive wheels begin to creep, an adjustment is required.
Neutral Creep Adjustment
1.Stop engine and lock the park brake.
2.Move both motion control levers to neutral detent position (standard
levers) or neutral lock position (optional “over the lap” levers).
12.Lower the rear of the machine to the ground.
13.Check maximum speed drift.
3.Raise the rear wheels off the ground and securely support the rear of
the machine.
Check Maximum Speed Drift
NOTE: When tilting the seat forward, do not tilt the seat so far
forward that it moves the motion control levers out of the neutral
detent position.
1.Check neutral creep, and adjust as needed.
2.Sit on the seat, and start the engine.
4.Tilt operator seat forward and support the seat frame.
3.Operate machine to bring the hydraulic oil to normal operating
temperature.
4.Move the machine in a level, wide-open area, such as an empty parking
lot.
5.Run the engine at full throttle.
6.Move and hold both control levers to the full forward position. Observe
the machine travel. If the machine does not travel in a straight line,
adjustment is required. Note the direction the machine moves.
Maximum Speed Drift Adjustment
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Tilt operator seat forward and support the seat frame.
5.Loosen nut (A), and move the dampener (B) in adjusting slot backward
or forward to stop machine creep.
• If machine creeps forward, slide dampener to the rear of the adjusting
slot. Tighten nut.
• If machine creeps backward, slide dampener to the front of the
adjusting slot. Tighten nut.
6.Check for creep, and if the machine still creeps, continue with the next
step.
Service Transmission - 28
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE TRANSMISSION
NOTE: If the machine travels to the left, adjust the right speed drift
screw (A). If the machine travels to the right, adjust the left speed
drift screw (B).
3.Adjust the appropriate speed drift screw (A or B) as follows:
a.Loosen jam nut (C or D).
b.Adjust the screw (A or B) one turn clockwise.
c.Tighten the jam nut (C or D).
4.Lower the seat platform.
5.Perform Check Maximum Speed Drift procedure to check adjustment.
Repeat the adjustment procedure as needed.
Service Transmission - 29
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE TRANSMISSION
Hydraulic System Hose Routing
A- Hydraulic Reservoir
B- Oil Filter
C- Right Hydraulic Pump
D- Right Wheel Motor
E- Left Wheel Motor
F- Left Hydraulic Pump
Service Transmission - 30
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE STEERING & BRAKES
Hydraulic System Schematic
J - Left Wheel Motor
K- Left Hydraulic Pump
L- Oil Filter
A- Control Input Shaft
B- Pump Block
M- Hydraulic Reservoir
C- Charge Pump
D- Charge System Check Valve
E- Right Hydraulic Pump
F- Manual Bypass (Free-Wheel) Valve
G- Right Wheel Motor
H- Cooling Orifice
Service Steering & Brakes
I - Charge Relief Valve
Service Steering & Brakes - 31
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE STEERING & BRAKES
Removing and Installing Front Caster Wheels
Removing
1.Park machine safely. (See Parking Safely in the SAFETY section.)
CAUTION: Avoid injury! The machine may fall or slip from an
unsafe lifting device or supports, injuring anyone beneath it.
• Remove key before raising machine.
• Use a safe lifting device rated for the load to be lifted.
• Lower machine onto stable supports or jack stands and
block wheels before servicing.
2.Lift front of machine with a safe lifting device.
3.Remove locknut (A), cap screw (B), two trash guards (C) and wheel and
tire assembly (D).
4.Remove bearings (E) and spacer tube (F) from wheel.
5.Wipe clean and inspect bearings (E). Replace bearings as needed.
6.Install spacer tube (F), press bearings (E) into wheel and tire assembly.
7.Install wheel and tire assembly (D), two trash guards (C), cap screw (B)
and locknut (A).
Adjusting Front Caster Spindle Bearing
NOTE: Adjustment required only if the front caster wheel shimmies
during travel.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
3.Remove hex nut (A) and wheel bolt (B).
4.Remove wheel (C) from assembly yoke.
Installing
1.Install replacement wheel (C).
2.Install wheel bolt (B) and hex nut (A).
3.Tighten nut.
4.Lower machine.
Servicing Front Caster Wheel Roller Bearings - Chariot
1.Park machine safely. (See Parking Safely in the SAFETY section.)
CAUTION: Avoid injury! The machine may fall or slip from an
unsafe lifting device or supports, injuring anyone beneath it.
•Remove key before raising machine.
2.Remove dust cover (A) from top of spindle.
•Use a safe lifting device rated for the load to be lifted.
•Lower machine onto stable supports or jack stands and
block wheels before servicing.
2.Raise and securely support the front of the mower deck.
Service Steering & Brakes - 32
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE STEERING & BRAKES
3.Remove cotter pin (B).
4.Turn castle nut (C) 1/4 turn clockwise.
5.Install a new cotter pin. Do not loosen the castle nut to align cotter pin
hole, tighten to align.
6.Replace dust cover.
7.Test machine to determine if shimmy is still present. Repeat adjustment
as necessary.
Servicing Caster Spindle Bearings
1.Park machine safely. (See Parking Safely in the SAFETY section.)
3.Remove cap (A), cotter pin (B), castle nut (C), caster yoke and wheel
assembly (D) and caster bushing (E).
CAUTION: Avoid injury! The machine may fall or slip from an
unsafe lifting device or supports, injuring anyone beneath it.
NOTE: It is not necessary to remove the bearing races (F and G),
unless the bearings need to be replaced.
•Remove key before raising machine.
4.Remove seal (H) and lower bearing (I).
5.Remove upper bearing (J).
•Use a safe lifting device rated for the load to be lifted.
•Lower machine onto stable supports or jack stands and
block wheels before servicing.
6.Clean and inspect bearings (I and J); pack with clean grease. Replace
bearings if needed.
2.Raise and securely support the front of the mower deck.
7.Install lower bearing (I).
8.Install caster bushing (E) into a new seal (H).
9.Install seal assembly (H).
10.Carefully install caster yoke and wheel assembly (D).
NOTE: Do not overtighten castle nut (C). Tighten castle nut only
enough to install the cotter pin (B). The caster wheel yoke assembly
must be free to rotate.
11.Install castle nut (C), cotter pin (B) and cap (A).
12.Apply grease to lubrication fitting (L).
Checking and Aligning Motion Control Levers -
Standard Center Steer Levers
Check Alignment:
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.The control lever gap is pre-set at the factory. If the gap requires
adjustment, see your authorized Great Dane servicing dealer.
Height Adjustment Procedure
The position of the control levers can be varied higher or lower by
approximately 25 mm (1 in.) depending on the holes chosen for mounting
the lever.
Service Steering & Brakes - 33
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE MOWER
• To mount in the high position, mount the levers to the top four holes in
the mounting bracket.
• Loosen cap screws (C).
• To mount in the low position, mount the levers to the bottom four holes in
the mounting bracket.
• Slide both levers forward or rearward to desired position on control
arm until levers are aligned.
• Tighten cap screws.
Checking and Aligning Motion Control Levers -
Optional Over the Lap Levers
Adjusting Park Brake
Check Alignment:
IMPORTANT: Avoid damage! Due to initial brake wear, the park
brake should be checked and adjusted after the first 25 hours of
use.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
A park brake that is adjusted too tightly could damage the
transmission or cause premature brake wear.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Move both motion control levers (A) from the neutral lock to the neutral
steer position.
3.Check levers for equal alignment.
• Check gap (B) between the levers. The recommended gap is 3-6 mm
(1/8-1/4 in.).
2.Loosen set screw (A).
3.Turn knob (B) clockwise several times.
4. Tighten set screw down in the lower slot.
5.Test park brake.
NOTE: If the ends of the levers strike against each other while in the
neutral position, move the levers to the neutral lock position and
carefully bend them outward. Move them back to the neutral position
and check for the recommended gap of 3-6 mm (1/8-1/4 in.).
• If positions of the control levers are unequal, an adjustment is
necessary.
Service Mower
Alignment Procedure
1.Adjust position of motion control levers:
Removing and Installing Mower Deck Foot Plate
CAUTION: Avoid injury! Always operate the mower with the
foot plate installed. Operating with the foot plate removed can
cause serious injury.
Service Mower - 34
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE MOWER
Removing Foot Plate
1.Park machine safely. (See Parking Safely in the SAFETY section.)
3.Remove knob (A).
4.Remove belt shield (B).
Installing Belt Shields
1.Install belt shield (B).
2.Install knob (A).
2.Raise foot plate (A) using hole (B).
Leveling Mower Deck
CAUTION: Avoid injury! Rotating blades are dangerous.
Before adjusting or servicing mower:
•Remove ignition key or disconnect battery negative (-)
cable to prevent engine from starting accidently.
•Always wear gloves when handling mower blades or
working near blades.
NOTE: Mower deck anti-scalp wheels should not contact the ground.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Inflate tires to the correct pressure.
3.Raise the mower deck lift lever to transport position.
4.Inspect mower blades for:
3.Remove and retain hardware (C) securing foot plate (A) on both sides of
machine.
• Blade sharpness.
4.Remove foot plate.
• Blade damage.
Installing Foot Plate
• Bent blades.
1.Install foot plate (A) using hardware (C) saved earlier.
2.Lower foot plate.
Checking Level (Side-to-Side)
NOTE: Mower deck anti-scalp wheels should not contact the ground.
1.Lower deck to the 76 mm (3 in.) cutting height position.
Removing and Installing Mower Deck Belt Shields
NOTE: Position the left mower blade in the sideways (left-to-right)
position.
CAUTION: Avoid injury! Help prevent serious personal injury.
Do not operate the mower without the belt shields installed.
Use a short ruler or a leveling gauge to check the mower blade level.
2.Measure from outside blade tip to the ground.
Removing Belt Shields
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Lower mower deck to the lowest cutting height position.
Service Mower - 35
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE MOWER
Picture Note: Discharge chute raised for photo clarity.
• The height (C) of the rear blade tip should be 3-6 mm (1/8-1/4 in.)
higher than the front blade tip.
3.Position right mower blade (A) (discharge side) in the side-to-side
position.
5.If the front-to-rear level is not within specifications, an adjustment is
necessary.
4.Measure from outside blade tip to the ground.
Adjusting Level (Front-to-Rear)
• The difference between both measurements should be no greater
than 3 mm (1/8 in.).
IMPORTANT: Avoid damage! Adjust the left and right deck lift
assist rods equally.
5.If side-to-side level is not within specifications, an adjustment is
necessary.
NOTE: Adjust side-to-side mower level before adjusting front-to-rear
level.
Adjusting Level (Side-to-Side)
1.Adjust four chain U-bolts (B) (two on each side of deck) until deck is
within 3 mm (1/8 in.) of level from side to side.
1.Loosen jam nut (D) on deck lift assist rod.
2.While positioned in front of the machine, adjust mower level:
• Turn hex nut (E) counterclockwise (F) to lower front of mower deck.
• Turn hex nut (E) clockwise (G) to raise front of mower deck.
3.Tighten jam nuts.
Checking Level (Front-to-Rear)
1.Lower mower deck to the 76 mm (3 in.) cutting height position.
2.Position right mower blade (discharge side) in the straight forward (front-
to-rear) position.
3.Measure from right front blade tip to the ground.
4.Check front-to-rear mower level.
4.Turn blade 180° and measure from right rear blade tip to the ground.
Service Mower - 36
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE MOWER
• To lower deck, turn nut (C) counterclockwise.
Checking and Adjusting Cutting Height
• To raise deck, turn nut (C) clockwise.
4.Tighten jam nut (A).
CAUTION: Avoid injury! Rotating blades are dangerous.
Before adjusting or servicing mower:
Adjusting Deck Lift Assist Spring Tension
•Remove ignition key or disconnect battery negative (-)
cable to prevent engine from starting accidently.
NOTE: Deck lift assist spring tension is adjusted at the factory. If the
effort required to raise or lower the mower deck is not satisfactory,
an adjustment may be necessary.
•Always wear gloves when handling mower blades or
working near blades.
Check Spring Tension
Checking Thrust Arm-to-Stop Rod Clearance (Transport Position)
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Set mower deck to transport (fully raised) position.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Raise the mower deck lift lever to the transport position.
3.Measure distance (A) between the washers (B) on each deck lift spring
assembly.
• The recommended factory setting is approximately 1 mm (1/32 in.)
gap between the spring coils at the lowest HOC setting.
3.Check clearance (A) from the top of the thrust arms (B) to the bottom of
the thrust arm stop rod (C). The clearance should be 3 mm (1/8 in.).
Adjust Assist Spring Tension
Adjust Thrust Arm-to-Stop Rod Clearance (Transport Position)
NOTE: Do not overtighten the deck lift assist springs. If the springs
are compressed too tightly, the mower deck will float too freely.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
Decrease deck lift assist spring tension if operating in rough terrain.
While positioned in front of the machine:
• Turn hex nut (C) clockwise to increase deck lift spring tension and
reduce the effort to raise and lower the mower deck.
• Turn hex nut (C) counterclockwise to decrease deck lift spring tension
and increase the effort to raise and lower the mower deck.
Checking and Adjusting Mower Deck Drive Belt
Tension
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Adjust the mower deck for the lowest cutting height, and lower the deck.
3.Raise foot platform.
2.Loosen jam nut (A).
NOTE: If correct adjustment cannot be obtained by adjusting the lift
handle connecting rod, further movement can be gained by
adjusting the chain U-bolts.
Adjust all four chain U-bolts equally. All four chains should be tight.
Tighten the U-bolt of the loose chain to correct.
3.Adjust deck lift handle connecting rod (B) while viewing adjusting
mechanism from rear of machine.
Service Mower - 37
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE MOWER
CAUTION: Avoid injury! Fingers and hands can be pinched or
crushed. Keeps hands clear of sheave and belt pinch points
when servicing belt.
5.Remove mower deck drive belt (B).
4.Loosen jam nut (A).
5.Check the mower deck drive belt (B) tension. The belt should deflect a
maximum of 13 mm (1/2 in.) when a force of 4.5 kg (10 lb) is applied to the
center of the longest span.
When properly adjusted, there would be approximately a 2 mm (1/16 in.)
gap between the spring coils.
• To increase belt tension: Turn nut (C) clockwise.
• To decrease belt tension: Turn nut (C) counterclockwise.
6.Tighten jam nut (A).
7.Lower foot platform.
Removing and Installing Mower Deck Drive Belt
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Raise foot platform.
A- PTO Clutch Sheave
B- Mower Deck Drive Belt
C- Tension Idler Sheave
D- Left Spindle Sheave
E- Center Spindle Sheave
F- Idler Sheave
3.Remove mower deck drive belt covers.
G- Right Spindle Sheave
H- Idler Sheave
6.Install new mower deck drive belt (B) as shown.
7.Adjust belt tension.
8.Install mower deck drive belt covers.
9.Lower foot platform.
Checking and Replacing Mower Blades
CAUTION: Avoid injury! Do not work near raised mower deck
unless it is safely supported.
4.Release mower deck drive belt tension by turning the tension adjuster
nut (A) counterclockwise.
•Mower blades are sharp. Wrap blades or wear gloves
when servicing.
•Before performing any service function, wait for all
moving parts to stop turning.
•Disconnect battery or remove spark plug wire before
making repairs.
Service Mower - 38
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE MOWER
IMPORTANT: Avoid damage! When replacing mower blades,
always use genuine Great Dane Service Parts.
CAUTION: Avoid injury! Mower blades are dangerous!
•Always wear gloves while working on blades.
•Always wear safety eye protection when grinding.
NOTE: Only replace blades. Never straighten or weld them.
Checking Mower Blades
• Sharpen blades with grinder, hand file, or electric blade sharpener.
1.Park machine safely. (See Parking Safely in the Safety Section).
2.Raise the mower deck to the transport position (also the 12.7 cm [5 in.]
cutting height position).
A
3.Raise front of machine with a safe lifting device.
• Support with jack stands and/or wooden blocks.
4.Check mower blades:
• Mower blades should be sharp and free of any damage.
• Inspect blades; sharpen/balance or replace as necessary.
Replacing Mower Blades
B
• Keep original bevel (A) when grinding.
• Blade should have 0.40 mm (1/64 in.) cutting edge (B) or less.
• Balance blades before installing.
Balancing Blades
CAUTION: Avoid injury! Mower blades are sharp. Always
wear gloves when handling mower blades or working near
blades.
1.Clean blade.
1.Use two long-handled 15/16 in. wrenches to loosen nut (A).
2.Remove nut (A), blade bolt (B), three 1/4 in. washers (C) and blade (D).
3.Install replacement blade:
• Blade wing must face toward top of mower deck.
IMPORTANT: Avoid damage! When installing the blade:
• Make sure the blade is properly seated on the spindle.
• Make sure the concave side of the large washer faces towards
the blade.
• Install blade bolt (B), blade (D), three 1/4 in. washers (C) and nut (A).
• Tighten blade nut to 81 N•m (60 lb-ft).
2.Put blade on nail in a vise. Turn blade to horizontal position.
3.Check balance. If blade is not balanced, heavy end of blade will drop.
4.Grind bevel of heavy end. Do not change blade bevel.
4.Lower machine.
5.Adjust mower deck to a desirable cutting height.
Replacing Mower Spindle Bearings
Sharpening Blades
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Remove mower blade. (See Checking and Replacing Mower Blades.)
Service Mower - 39
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE ELECTRICAL
cancer and reproductive harm. Wash hands after handling.
Service the Battery Safely
CAUTION: Avoid injury! The battery produces a flammable
and explosive gas. The battery may explode:
•Do not smoke near battery.
•Wear eye protection and gloves.
•Do not allow direct metal contact across battery posts.
•Remove negative cable first when disconnecting.
•Install negative cable last when connecting.
Removing and Installing the Battery
Removing:
1.Park machine safely. (See Parking Safely in the SAFETY section.)
3.Remove nut (A), pulley (B) and spacer (C).
4.Remove retaining ring (D), spindle shaft (E), lower bearing (F) and
spacer (G) from spindle housing (H). Discard bearing.
5.Remove and discard upper bearing (I).
6.Clean entire assembly.
7.Install a new lower bearing (F) and spacer (G) on the spindle shaft (E).
IMPORTANT: Avoid damage! The clearance between the lower
bearing and the housing is only 0.05 mm (0.002 in.). Do not force
bearing into housing.
8.Install the spindle shaft (E), lower bearing (F) and spacer (G) into the
spindle housing (H).
9.Install the upper bearing (I) and retaining ring (D).
10.Install spacer (C).
11.Install pulley (B) and nut (A). Tighten nut to 61 N•m (50 lb-ft).
2.Slide black cover (A) away from the negative battery terminal and
disconnect the negative battery cable (B).
12.Install mower blade, blade washers and blade bolt assembly. Tighten
nut to 81 N•m (60 lb-ft). (See Checking and Replacing Mower Blades.)
3.Slide red cover (C) away from the positive battery terminal and
disconnect the positive battery cable (D).
4.Remove nuts (E) and washers from both sides of the bracket (F).
5.Remove bracket (F) and J-bolts (G).
Service Electrical
6.Remove battery (H).
WARNING: Battery posts, terminals and related accessories contain lead
and lead components, chemicals known to the State of California to cause
Service Electrical - 40
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE ELECTRICAL
Installing:
IMPORTANT: Avoid damage! Electric charge from booster battery
can damage machine components. Do not install negative
booster cable to machine frame. Install only to the engine block.
1.Install battery (H) using J-bolts (G), bracket (F), washers and nuts (E).
2.Connect the positive battery cable (D) first, then the negative cable (B).
Install negative booster cable away from moving parts in the
engine compartment, such as belts and fan blades.
3.Apply petroleum jelly or silicone spray to the terminals to prevent
corrosion.
4.Connect the other end (F) of negative (–) booster cable to a metal part of
the disabled machine engine block away from battery.
4.Slide covers (A and C) over battery terminals.
Cleaning Battery and Terminals
5.Start the engine of the disabled machine and run machine for several
minutes.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Disconnect and remove battery.
6.Carefully disconnect the booster cables in the exact reverse order:
negative cable first and then the positive cable.
3.Wash battery with a solution of four tablespoons of baking soda to one
gallon of water. Be careful not to get the soda solution into the battery
cells.
Replacing Fuse
One 20-amp fuse is located behind the seat area.
4.Rinse the battery with plain water and dry.
5.Clean terminals and battery cable ends with wire brush until bright.
6.Install battery.
IMPORTANT: Avoid damage! When replacing fuses - use only a
20-amp fuse or you may damage the circuit.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
7.Attach cables to battery posts using washers and nuts (H).
8.Apply petroleum jelly or silicone spray to terminals to prevent corrosion.
Using Booster Battery
CAUTION: Avoid injury! The battery produces a flammable
and explosive gas. The battery may explode:
•Do not smoke or have open flame near battery.
•Wear eye protection and gloves.
•Do not jump start or charge a frozen battery. Warm
battery to 16°C (60°F).
•Do not connect the negative (-) booster cable to the
negative (-) terminal of the discharged battery. Connect
at a good ground location away from the discharged
battery.
2.Remove defective fuse (A) from socket.
3.Check metal clip in fuse window and discard fuse if clip is broken.
4.Install new fuse in socket.
Burnishing the PTO Clutch
NOTE: The clutch will only require burnishing if a new clutch has
been installed.
1.Start and run the engine at 1/2 throttle.
2.Engage and disengage the PTO clutch five times (ten seconds on, ten
seconds off).
3.Move throttle lever to 3/4 throttle.
4.Engage and disengage the PTO clutch five times (ten seconds on, ten
seconds off).
A- Booster Battery
B- Disabled Vehicle Battery
1.Connect positive (+) booster cable to booster battery (A) positive (+)
post (C).
2.Connect the other end of positive (+) booster cable to the disabled
vehicle battery (B) positive (+) post (D).
3.Connect negative (–) booster cable to booster battery negative (–) post
(E).
Service Electrical - 41
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE ELECTRICAL
Wiring Schematic
Service Electrical - 42
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE MISCELLANEOUS
2.Allow engine to cool.
Service Miscellaneous
3.Remove any trash from area around fuel tank cap.
4.Remove fuel tank cap slowly to allow any pressure built up in tank to
escape.
Using Proper Fuel
Use regular grade unleaded fuel with an octane rating of 87 octane or
higher. Fuel blends containing up to 10% ethanol or up to 15% MTBE
reformulated fuel are acceptable. Do not use fuel or additives containing
methanol as engine damage can occur.
5.Fill fuel tank only to bottom of filler neck.
6.Install fuel tank cap.
Always use fresh, clean fuel that is purchased in a quantity that can be
used within approximately 30 days, or add fuel stabilizer.
Checking Tire Pressure
Fuel is blended to give best seasonal performance. To avoid engine
performance problems such as hard starting or vapor lock, use in-season
fuel. Use fuel during warm weather that was purchased during that
season, and use fuel during cold weather that was purchased during that
season.
Fuel can become stale in machines with engines that are used seasonally
or infrequently during a season. Stale fuel can produce varnish and plug
carburetor components which can affect engine performance.
Keep fuel storage container tightly covered and in a cool area out of direct
sunlight. Fuel can break down and degrade if not sealed properly or
exposed to sun and heat.
Condensation may collect in the fuel tank because of a variety of
operating or environmental conditions and, over time, may affect your
machine’s operation. Fill fuel tank at the end of daily use and store fuel in
plastic containers to reduce condensation.
For best year-round performance and fuel-handling, add stabilizer to fuel
immediately after fuel purchase. Such practice helps prevent engine
performance problems and allows fuel storage in the machine all year
without draining.
CAUTION: Avoid injury! Explosive separation of tire and rim
parts is possible when they are serviced incorrectly:
•Do not attempt to mount a tire without the proper
equipment and experience to perform the job.
Filling Fuel Tank
•Do not inflate the tires above the recommended
pressure.
CAUTION: Avoid injury! Fuel vapors are explosive and
flammable:
•Do not weld or heat a wheel and tire assembly. Heat can
cause an increase in air pressure resulting in an
explosion. Welding can structurally weaken or deform
the wheel.
•Shut engine off before filling fuel tank.
•Do not smoke while handling fuel.
•Do not stand in front or over the tire assembly when
inflating. Use a clip-on chuck and extension hose long
enough to allow you to stand to one side.
•Keep fuel away from flames or sparks.
•Fill fuel tank outdoors or in well ventilated area.
•Clean up spilled fuel immediately.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
2.Check tires for damage.
•Use clean approved non-metal container to prevent
static electric discharge.
3.Check tire pressure with an accurate gauge.
4.Add air, if necessary:
•Use clean approved plastic funnel without screen or
filter to prevent static electric discharge.
Tire Size
Pressure
IMPORTANT: Avoid damage! Dirt and water in fuel can cause
engine damage:
Front: 13 x 5.0-6
Rear - Chariot: 23 x 9.5-12
110-138 kPa (16-20 psi)
69-97 kPa (10-14 psi)
• Clean dirt and debris from the fuel tank opening.
• Use clean, fresh, stabilized fuel.
Removing and Installing Rear Drive Wheels
Removing:
• Fill the fuel tank at the end of each day’s operation to keep
condensation out of the fuel tank.
• Use a non-metallic funnel with a plastic mesh strainer when
filling the fuel tank or container.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
Fill fuel tank at the end of each day’s operation to prevent condensation
and freezing during cold weather.
1.Park machine safely. (See Parking Safely in the SAFETY section.)
Service Miscellaneous - 43
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Cleaning and Repairing Plastic Surfaces
Your authorized dealer has the professional materials needed to properly
remove surface scratches from any plastic surfaces, do not attempt to
paint over marks or scratches in plastic parts.
IMPORTANT: Avoid damage! Improper care of machine plastic
surfaces can damage that surface:
• Do not wipe plastic surfaces when they are dry. Dry wiping will
result in minor surface scratches.
• Use a soft, clean cloth (bath towel, diaper, automotive mitt).
• Do not use abrasive materials, such as polishing compounds,
on plastic surfaces.
• Do not spray insect repellent near machine.
1.Wash surface with clean water and a mild liquid automotive washing
soap.
2.Dry thoroughly to avoid water spots.
Cleaning and Repairing Metal Surfaces
2.Slightly loosen five wheel nuts (A).
Cleaning:
Follow automotive practices to care for your vehicle painted metal
surfaces. Use a high-quality automotive wax regularly to maintain the
factory look of your vehicle’s painted surfaces.
CAUTION: Avoid injury! The machine can fall or slip from an
unsafe lifting device or supports.
•Use a safe lifting device rated for the load to be lifted.
Repairing Minor Scratches (surface scratch):
•Lower machine onto jack stands or other stable
supports and block wheels before servicing.
1.Clean area to be repaired thoroughly.
IMPORTANT: Avoid damage! Do not use rubbing compound on
painted surfaces.
IMPORTANT: Avoid damage! Place jack stands under frame, not
under transmission or engine, when raising or supporting
machine.
2.Use automotive polishing compound to remove surface scratches.
3.Apply wax to entire surface.
3.Lift machine with a safe lifting device.
4.Remove wheel nuts.
Repairing Deep Scratches (bare metal or primer showing):
1.Clean area to be repaired with rubbing alcohol or mineral spirits.
5.Remove wheel and tire assembly (B).
2.Use paint stick with factory-matched colors available from your
authorized dealer to fill scratches. Follow directions included on paint stick
for use and for drying.
Installing Rear Drive Wheels/Tightening Hardware:
1.Install new wheel and tire assembly.
3.Smooth out surface using an automotive polishing compound. Do not
use power buffer.
4.Apply wax to surface.
Troubleshooting
Using Troubleshooting Chart
If you are experiencing a problem that is not listed in this chart, see your
authorized dealer for service.
When you have checked all the possible causes listed and you are still
experiencing the problem, see your authorized dealer.
2.Install and tighten wheel nuts in numbered sequence shown for safe
wheel installation. Tighten alternately until recommended torque value is
reached.
• Tighten nuts to 100 N•m (75 lb-ft).
3.Lower machine.
Troubleshooting - 44
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Engine
If
Check
If
Check
Engine Lacks Power
Plugged air intake system.
Plugged fuel filter.
Engine Will Not Start or Is
Hard to Start
Motion control levers not in the neutral
detent (or neutral lock) position.
Improper type of fuel. Drain tank and fill
with correct fuel.
Park brake lever unlocked.
Key switch not in proper position.
PTO engaged.
Clean cooling fins to help prevent
overheating.
Replace spark plug.
Loose or corroded starter cable
connections.
Engine Uses Too Much Oil
Find and correct oil leaks.
Incorrect engine oil.
Plugged oil filter.
Stale or improper fuel/fuel level.
Plugged fuel filter.
Plugged air intake filter.
Plugged air intake filter.
Spark plug wire is loose or
disconnected.
Engine Backfires Through
Muffler
Throttle should be at low idle for several
seconds before turning off machine.
Spark plug not gapped correctly.
Leaking/damaged exhaust manifold
gasket.
Blown 20-amp fuse (main power
circuit).
High Fuel Consumption
Improper type of fuel.
Carbureted Engines Only: Blown
fusible link (charging circuit).
Plugged air intake system.
Electrical problem - dead battery.
Operating at too fast ground speed for
conditions.
Choke adjusted incorrectly. See your
Great Dane servicing dealer.
Improper valve clearance. See your
Great Dane servicing dealer.
Engine Will Not Slow Idle
Bent or kinked throttle cable.
Bent governor control.
Restricted air intake system.
Incorrect governor idle control.
Electrical System
Carburetion problems. See your Great
Dane servicing dealer.
If
Check
Engine Runs Rough or Stalls Plugged fuel filter.
Plugged air intake system.
Starter Will Not Work
Dead battery.
Blown 20-amp fuse (main power
circuit).
Fuel cap vent dirty.
Blown fusible link (charging circuit).
Stale or improper fuel/fuel level.
Spark plug not gapped correctly.
Replace spark plug.
Loose or corroded battery or ground
connections.
Loose or corroded starter cable
connections.
Choke adjusted incorrectly. See your
Great Dane servicing dealer.
Neutral start switches faulty or not
adjusted properly. See your Great Dane
servicing dealer.
Engine Knocks
Engine oil level low.
Reduce load. (Slower ground speed.)
Key switch or starter faulty. See your
Great Dane servicing dealer.
Fuel is bad. Fill tank with fresh fuel,
correct octane.
PTO engaged.
Idle speed too slow.
Motion control levers and park brake
lever not in proper position.
Engine Overheats
Clean cooling fins.
Low oil level.
Battery Will Not Charge
Loose or corroded battery or ground
connections.
Do not operate at slow idle. Operate at
full-throttle setting.
Blown fusible link (charging circuit).
Battery cables and terminals are dirty.
Dead cell in battery.
Cooling air intake screen is dirty.
Plugged air intake filter.
Operating at too fast ground speed for
conditions.
Troubleshooting - 45
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
If
Check
If
Check
PTO Clutch Does Not
Engage
Blown 20-amp fuse (main power
circuit).
Machine Will Not Follow a
Straight Path
Steering tracking out of adjustment.
Faulty PTO switch.
Machine Moves to the Left or Pump linkage (neutral position) out of
Faulty PTO clutch.
Right With Engine Running
and Transmission in Neutral
adjustment.
Loose PTO clutch connections.
Starter Turns Slowly
Loose or corroded battery or ground
connections.
Mower Deck
Low battery power - charge battery.
Engine oil viscosity too heavy.
If
Check
Discharge Chute Plugged
Grass is wet - mow grass only when
dry.
Hydraulic pump linkages failed and are
engaged.
Raise cutting height.
Mow at full throttle.
Machine
Ground speed too fast for conditions.
Correct installation of deck drive belt.
If
Check
Excessive Machine Vibration Engine speed too slow.
Mower Deck Vibrates
Run engine at full throttle.
Loose hardware.
Machine Will Not Move With
Engine Running
Park brake locked.
Check/replace mower deck drive belt.
Blades bolts are loose.
Transmission hydraulic oil level low.
Transmission oil cold - allow engine to
warm.
Blades are bent or worn.
Sharpen and balance blades.
Traction drive belt slipping.
Hydraulic pump free-wheel valves
open.
Remove belt shields and check for
debris on sheaves.
Traction drive belt damaged or worn.
Check sheaves for proper alignment or
damage. See your Great Dane
servicing dealer.
Hydrostatic pump and/or wheel motor
problems. See your Great Dane
servicing dealer.
Mower Blades Do Not
Engage
Mower deck drive belt slipping or
broken.
Machine Creeps With Engine Needs shift control linkage adjustment.
Running and Motion Control
Mower deck belt tension spring not
installed or broken.
Levers in a Neutral Position
PTO switch failure.
Park Brake
20-amp fuse is blown (main power
circuit).
If
Check
Loose electrical connections.
Faulty PTO clutch.
Park Brake Not Working
Correctly
Brakes out of adjustment - adjust
linkage.
Mower Mows Unevenly
Mower deck not properly leveled.
Ground speed too fast for conditions.
Run engine at full throttle.
Brake drums wet.
Worn brake shoes.
Brake cable damaged.
Reduce ground speed when making
turns.
Steering
Blades are bent or worn.
Sharpen or replace blades.
Change mowing pattern.
Check tire pressure.
If
Check
Steering Not Working
Park brake locked.
Hydraulic pump free-wheel valves
partially open.
Improper tire Inflation.
Hydrostatic transmission oil low.
Traction drive belt slipping.
Traction drive belt damaged or worn.
Troubleshooting - 46
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
for longer than 60 days.
Storage
1.Change engine oil and filter while engine is warm.
2.Service air filter if necessary.
Storing Safety
3.Clean debris from engine air intake screen.
4.On gas engines:
CAUTION: Avoid injury! Fuel vapors are explosive and
• Remove spark plugs. Put 30 mL (1 oz) of clean engine oil in cylinders.
• Install spark plugs, but do not connect spark plug wires.
• Crank the engine five or six times to allow oil to be distributed.
5.Clean the engine and engine compartment.
6.Remove battery.
flammable. Engine exhaust fumes contain carbon monoxide
and can cause serious illness or death:
•Run the engine only long enough to move the machine
to or from storage.
•Do not store vehicle with fuel in the tank inside a
building where fumes may reach an open flame or spark.
7.Clean the battery and battery posts. Check the electrolyte level, if your
battery is not maintenance free.
•Allow the engine to cool before storing the machine in
any enclosure.
8.Close fuel shut-off valve, if your machine is equipped.
9. Store the battery in a cool, dry place where it will not freeze.
NOTE: The stored battery should be recharged every 90 days.
10. Charge the battery.
Preparing Machine for Storage
1.Repair any worn or damaged parts. Replace parts if necessary. Tighten
loose hardware.
2.Repair scratched or chipped metal surfaces to prevent rust.
3.Remove grass and debris from machine.
IMPORTANT: Avoid damage! Prolonged exposure to sunlight
could damage the hood surface. Store machine inside or use a
cover if stored outside.
4.Clean under the deck and remove grass and debris from inside chute
and bagger.
5.Wash the machine and apply wax to metal and plastic surfaces.
6.Run machine for five minutes to dry belts and pulleys.
7.Apply light coat of engine oil to pivot and wear points to prevent rust.
8.Lubricate grease points and check tire pressure.
11. Store the vehicle in a dry, protected place. If vehicle is stored outside,
put a waterproof cover over it.
Removing Machine From Storage
1.Check tire pressure.
2.Check engine oil level.
Preparing Fuel and Engine For Storage
3.Check battery electrolyte level, if your battery is not maintenance free.
Charge battery if necessary.
Fuel:
If you have been using “Stabilized Fuel,” add stabilized fuel to tank until
the tank is full.
4.Install battery.
5.On gas engines: Check spark plug gap. Install and tighten plugs to
specified torque.
NOTE: Filling the fuel tank reduces the amount of air in the fuel tank
and helps reduce deterioration of fuel.
6.Lubricate all grease points.
If you are not using “Stabilized Fuel:”
7.Open fuel shut-off valve, if your machine is equipped.
1.Park machine safely in a well-ventilated area. (See Parking Safely in the
SAFETY section.)
8.Run the engine 5 minutes without the mower or any attachments
running to allow oil to be distributed throughout engine.
NOTE: Try to anticipate the last time the machine will be used for the
season so very little fuel is left in the fuel tank.
9.Be sure all shields and guards or deflectors are in place.
2.Turn on engine and allow to run until it runs out of fuel.
3.For machines equipped with key switch, turn key to off position.
Assembly
IMPORTANT: Avoid damage! Stale fuel can produce varnish and
plug carburetor or injector components and affect engine
performance.
Bag of Parts
Qty.
1
Description
Key
• Add fuel conditioner or stabilizer to fresh fuel before filling tank.
4.Mix fresh fuel and fuel stabilizer in separate container. Follow stabilizer
instructions for mixing.
1
Operator’s Manual
PDR Check List
5.Fill fuel tank with stabilized fuel.
1
6.Run engine for a few minutes to allow fuel mixture to circulate through
carburetor on gas engine or fuel injectors on diesel engine.
Prepare for Assembly
Engine:
• Remove machine from the shipping crate:
• Remove box containing operator seat.
Engine storage procedure should be used when vehicle is not to be used
Storage - 47
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• Cut plastic tie straps fastening the front wheels to the shipping crate.
Install Motion Control Levers
• Cut plastic tie straps holding the discharge chute up.
1.Remove hardware from control arms.
• Cut plastic tie straps securing the motion control levers to the
machine.
Check Fluid Levels
NOTE: Refer to the Service sections of the operator’s manual for
information regarding check locations and proper fluid levels.
• Check engine oil level.
• Check hydraulic oil level.
Check Tire Pressure
CAUTION: Avoid injury! Explosive separation of tire and rim
parts is possible when they are serviced incorrectly:
•Do not attempt to mount a tire without the proper
equipment and experience to perform the job.
•Do not inflate the tires above the recommended
pressure.
NOTE: The control lever mounting brackets have six holes. The
levers can be installed in the top four holes, or for a lower lever
position, install the levers in the lower four holes.
•Do not weld or heat a wheel and tire assembly. Heat can
cause an increase in air pressure resulting in an
explosion. Welding can structurally weaken or deform
the wheel.
2. Raise the seat and prop it in the upright position.
NOTE: It is easiest during installation if the bottom rear bolts are
loosely installed first prior to installation of the front bolts.
•Do not stand in front or over the tire assembly when
inflating. Use a clip-on chuck and extension hose long
enough to allow you to stand to one side.
3. Align motion control levers (A) with control arms. Install hardware and
tighten.
1.Check tires for damage.
2.Check tire pressure with an accurate gauge.
3.Add or remove air, if necessary.
3.Check motion control lever alignment.
• Move both motion control levers forward.
Install Seat
Assembly - 48
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
1.Remove and retain the two locknuts and cap screws securing the
flanges at the rear of the seat frame to the machine.
Install ROPS
1.Support rear of bumper with wooden blocks or jack.
2.Loosen nut (A) securing the rear battery hold-down rod and disengage
hooked end (B) from bumper.
3.Remove all bumper mounting bolts and retaining hardware except for
the lower left cap screw (C) at each side of the machine. Discard any
assembly washers, retain bolts and locknuts for later use.
2.Pivot seat frame (A) forward until it rests on the hinge stops.
3.Remove and retain the seat pivot shoulder bolts (B) and nuts.
4.Remove protective covers from seat screws.
NOTE: The seat mounting hardware is attached to the seat plate with
tie straps.
4.Fold ROPS to the upright operating position and install lock pins (D) and
spring pins (E).
5.Install seat (C) to the seat frame (A), using four 5/16-18 locknuts and
heavy flat washers (D). Tighten locknuts to 27 N•m (20 lb-ft).
6.Connect wire harness to seat safety switch (E).
7.Secure front of seat frame to machine with seat pivot shoulder bolts and
nuts, removed earlier. Tighten to 81 N•m (60 lb-ft).
8.Secure rear of seat frame to machine with capscrews and locknuts,
removed earlier.
Assembly - 49
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Check Safety System
For a complete checkout procedure of the safety interlock system, see
Testing the Safety Interlock System in the Operating section.
CAUTION: Avoid injury! Machine component is heavy. Use a
safe lifting device or get an assistant to help lift and hold
component into place for installation.
Initial Adjustments
NOTE: Using a tapered drift will aid in the alignment of mounting
holes and ease installation of cap screws.
CAUTION: Avoid injury! Clear area of all bystanders before
performing this service procedure.
1.Check free-wheel valves on both pump assemblies to make sure that
the valves are closed. Tighten valves to 108-163 N•m (80-120 lb-ft).
2.Raise the rear of the machine until the drive wheels are off the ground.
Support the machine with jackstands.
CAUTION: Avoid injury! Engine exhaust fumes contain
carbon monoxide and can cause serious illness or death.
•Move the machine to an outside area before running the
engine.
•Do not run an engine in an enclosed area without
adequate ventilation.
5.Lay ROPS on the ground, slide it up to the bumper and align the
appropriate hole in the ROPS flange with the lower rear mounting holes in
the machine frame and bumper. Install an M10 cap screw, removed
earlier, through the hole from the inside and secure loosely with an M10
locknut (F).
•Connect a pipe extension to the engine exhaust pipe to
direct the exhaust fumes out of the area.
•Allow fresh outside air into the work area to clear the
exhaust fumes out.
6. Remove cap screw (C).
3.Start and run the engine until it reaches normal operating temperature.
NOTE: Take care when raising ROPS to avoid damaging paint on
bumper.
4.Move control levers to the forward position and observe drive wheel
rotation; the drive wheels should rotate in the correct direction.
5.Move the control levers to the reverse position and observe drive wheel
rotation; the drive wheels should rotate in the correct direction.
6.Move PTO clutch switch to on position; mower clutch should engage.
Run blades for several minutes.
7.Move PTO clutch switch to off position and shut the engine off.
8.Check all belts for proper tension.
9.Start the engine and test drive the machine in an open area. Drive the
machine forward; if the machine drifts to the right or left, adjust the
transmission control linkage.
Specifications
7.Using the lower rear bolts as a pivot, raise ROPS to the vertical position,
and install remaining cap screws and locknuts (F) on each side. Tighten all
ROPS mounting hardware to 80 N•m (59 lb-ft).
Engine
NOTE: See engine manufacturer’s owner’s manual provided with
your machine for engine specifications.
8.Engage hooked end (B) of rear battery hold-down rod in slot in bumper
and tighten nut to secure.
Battery
Lubricate Machine
Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 volt
CCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .340 amp
Reserve Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 minutes
BCI Group Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Lubricate all moving parts before operating the machine. See Lubrication
Points in the Service Lubrication section.
Check Mower Deck Level
The mower deck is assembled and adjusted at the factory. After machine
is completely assembled, check the mower front-to-rear and side-to-side
deck level.
Tires
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 x 5.0-6
Rear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 x 9.50-12
Inflation Front (Maximum) . . . . . . . . . . . . . . . . . . 110-138 kPa (16-20 psi)
Specifications - 50
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING QUALITY SERVICE
Inflation Rear (Maximum) . . . . . . . . . . . . . . . . . . . . .69-97 kPa (10-14 psi)
Wheel Nut Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 N•m (75 lb-ft)
Getting Quality Service
Service Literature
Capacities
If you would like to order a copy of the Parts Catalog or Operator Manual
for this machine, contact your dealer. Parts catalogs and operator manuals
are also available online at GreatDaneMowers.com.
Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30.2 L (8 gal)
Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.54 L (3.75 qt)
Net Weight - Chariot (With Mower Deck and Without
Fuel)
Parts
We recommend Great Dane quality parts available at your Great Dane
dealer.
23-hp Kohler Engine/48-in. Deck . . . . . . . . . . . . . . . . . . . 499 kg (1100 lb)
25-hp Kawasaki Engine/52-in. Deck . . . . . . . . . . . . . . . . . 508 kg (1119 lb)
27-hp Kohler Engine/52-in. Deck . . . . . . . . . . . . . . . . . . 510 kg (1124 lb)
25-hp Kawasaki Engine/61-in. Deck . . . . . . . . . . . . . . . . 519 kg (1144 lb)
27-hp Kohler Engine/61-in. Deck . . . . . . . . . . . . . . . . . . 521 kg (1149 lb)
Part numbers may change, use part numbers listed below when you order.
If a number changes, your dealer will have the latest number.
When you order parts, your Great Dane dealer needs your machine serial
number and engine serial number. These are the numbers that you
recorded in the Product Identification section of this manual.
Travel Speeds
Great Dane Quality Continues with Quality Service
Forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-18 km/h (0-11 mph)
Reverse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-8 km/h (0-5 mph)
Great Dane provides a process to handle your questions or problems,
should they arise, to ensure that product quality continues with your
authorized Great Dane dealer’s parts and service support.
Dimensions
Follow the steps below to get answers to any questions you may have
about your product.
Wheel Base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10 m (43.375 in.)
Track Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.21 m (47.5 in.)
Overall Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.09 m (42.75 in.)
Overall Length (with Kawasaki Engines). . . . . . . . . . . . . .1.92 m (75.5 in.)
Overall Length (with Kohler Engines) . . . . . . . . . . . . . . 1.97 m (77.75 in.)
Overall Width (with 48-in. Deck) . . . . . . . . . . . . . . . . . . . . . 1.50 m (59 in.)
Overall Width (with 52-in. Deck) . . . . . . . . . . . . . . . . . . . . . 1.63 m (64 in.)
Overall Width (with 61-in. Deck) . . . . . . . . . . . . . . . . . 1.86 m (73.375 in.)
1.Refer to your attachment and machine operator manuals.
2.Contact your authorized Great Dane dealer with unanswered questions.
48-Inch Mower Deck
Mower Type. . . . . . . . . . . . . . . . . . . . . . . . . Mulch, Bag or Side Discharge
Cutting Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Blade Bolt Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 N•m (60 lb-ft)
Cutting Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.22 m (48 in.)
Cutting Height (approximate) . . . . . . . . . . . . . . . 25 to 127 mm (1 to 5 in.)
Height Adjustment Increments . . . . . . . . . . . . . . . . . . . . . 13 mm (1/2 in.)
52-Inch Mower Deck
Mower Type. . . . . . . . . . . . . . . . . . . . . . . . . Mulch, Bag or Side Discharge
Cutting Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Blade Bolt Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 N•m (60 lb-ft)
Cutting Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.32 m (52 in.)
Cutting Height (approximate) . . . . . . . . . . . . . . . 25 to 127 mm (1 to 5 in.)
Height Adjustment Increments . . . . . . . . . . . . . . . . . . . . . .13 mm (1/2 in.)
61-Inch Mower Deck
Mower Type. . . . . . . . . . . . . . . . . . . . . . . . . Mulch, Bag or Side Discharge
Cutting Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Blade Bolt Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 N•m (60 lb-ft)
Cutting Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.55 m (61 in.)
Cutting Height (approximate) . . . . . . . . . . . . . . . 25 to 127 mm (1 to 5 in.)
Height Adjustment Increments . . . . . . . . . . . . . . . . . . . . . 13 mm (1/2 in.)
Getting Quality Service - 51
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE AND RELATED COMPONENTS - KAWASAKI
ENGINE AND RELATED COMPONENTS - KAWASAKI - 52
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE AND RELATED COMPONENTS - KAWASAKI
Ref. No.
Part No.
14M7166
19M7897
200318
Description
LOCK NUT
Qty.
4
4
Remarks
1
2
3
M8
M8 X 35
SCREW
PULLEY
1
ENGINE TO PUMP
4
5
GDA10017
D18056
CLUTCH
SPACER
1
1
MAG-STOP ELECTRIC
6
7
8
9
D14208
LOCK WASHER
CAP SCREW
DRAIN VALVE
SHAFT KEY
CLAMP
1
1
1
1
19H2531
TCA16240
D18145
7/16" X 3"
10
11
12
13
14
15
16
17
18
19
20
21
22
D18379
1
M76926
M78480
M136651
GD10128
H137328
03M7184
D22236
12M7065
14M7273
200316
TUBE
TIE BAND
GASKET
MUFFLER
LOCK NUT
BOLT
ANGLE
LOCK WASHER
NUT
BRACKET
BOLT
FLANGE NUT
1
2
2
1
2
2
1
4
4
1
2
2
25 HP
25 HP
M8 X 20
M8
M8
03M7017
14M7518
M10 X 25
M10
ENGINE AND RELATED COMPONENTS - KAWASAKI - 53
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE AND RELATED COMPONENTS - KOHLER 27 HP
ENGINE AND RELATED COMPONENTS - KOHLER 27 HP - 54
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE AND RELATED COMPONENTS - KOHLER 27 HP
Ref. No.
Part No.
14M7396
19M8317
200311
Description
LOCK NUT
Qty.
4
4
Remarks
1
2
3
M8
M8 X 40
SCREW
PULLEY
1
ENGINE TO PUMP
4
5
6
7
GDA10122
GDU10312
D14208
CLUTCH
SPACER
LOCK WASHER
BOLT
1
1
1
1
MAG-STOP ELECTRIC
D24022
8
9
TCA15389
D18145
230687
M78480
M132446
D28121
12M7065
14M7273
200316
HOSE
1
1
1
2
2
1
4
4
OIL DRAIN
SHAFT KEY
FITTING PLUG
TIE BAND
GASKET
MUFFLER
LOCK WASHER
NUT
BRACKET
BOLT
FLANGE NUT
10
11
12
13
14
15
16
17
18
M8
M8
M8
M10 X 25
M10
1
2
2
03M7017
14M7518
NOTES
ENGINE AND RELATED COMPONENTS - KOHLER 27 HP - 55
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL DELIVERY SYSTEM COMPONENTS
Ref. No.
Part No.
181251
M88753
R56101
Description
FILLER CAP
Qty.
1
1
Remarks
1
2
3
HOSE
CLIP
2
4
5
6
7
GDA10012
D18144
GDU10026
M63277
E53830
FUEL TANK
BUSHING
FUEL PICKUP
LOCK NUT
CLAMP
1
1
1
2
(INCLUDES M145626)
7.925 MM (5/16")
8
2
9
M63277
N10213
D14235
GDU10028
24H1776
LOCK NUT
LOCK NUT
BOLT
STRAP
WASHER
2
1
2
2
7.925 MM (5/16")
7.925 MM (5/16")
7.925 MM X 63.5 MM (5/16"X 2-1/2")
10
11
12
13
2
5/16" X 47/64" X .065
FUEL DELIVERY SYSTEM COMPONENTS - 56
Download from Www.Somanuals.com. All Manuals Search And Download.
OVER THE LAP CONTROL ASSEMBLY
Ref. No.
Part No.
TCU14989
Description
Qty.
2
2
2
4
4
2
2
2
Remarks
1
2
3
4
5
6
7
8
9
TUBE
GRIP
STRAP
SCREW
M131171
GDU10047
19M8320
14M7518
03M7195
M85516
TCU13271
GDU10275
37M7059
M10 X 45
M10
M10 X 45
M10
FLANGE NUT
BOLT
LOCK NUT
ARM
COVER
SCREW
1
3
10
M5 X 12
OVER THE LAP CONTROL ASSEMBLY - 57
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL AND RELATED COMPONENTS
ELECTRICAL AND RELATED COMPONENTS - 58
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL AND RELATED COMPONENTS
Ref. No.
1
Part No.
57M7120
D18334
Description
Qty.
1
2
1
1
1
2
1
1
1
1
3
2
3
3
1
1
2
2
1
1
1
1
4
4
2
5
1
1
3
2
2
1
1
1
2
2
1
1
2
1
1
1
1
Remarks
FUSE
SWITCH
NUT
SWITCH
KEY
20 AMP
NEUTRAL
2
3
4
5
6
7
8
9
M110159
AM101561
TCU17401
24M7349
GDA10060
GDA10055
GDA10109
GDA10110
M78480
AM123716
21M7246
14M7397
AM118802
AM129887
D14304
IGNITION
WASHER
21 X 37 X 3 MM
WIRING LEAD
WIRING HARNESS
WIRING HARNESS
WIRING LEAD
TIE BAND
KAWASAKI
KAWASAKI
CARBURETED KOHLER
GROUND (FUEL PUMP) KOHLER
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
**
RELAY
SCREW
M6 X 16
M6
LOCK NUT
SWITCH
HOUR METER
BOLT
LOCK NUT
SWITCH
SWITCH
BLADE ENGAGEMENT
D14305
D38001
D28055
GDA10017
GDA10122
D14288
PARK BRAKE
SEAT
CLUTCH
CLUTCH
1" HUB
1.125" HUB
SCREW
M63431
LOCK NUT
FLANGE NUT
DIODE
H122207
AM101006
TCU17832
D38018
1000V -3AMP
400V - 6AMP
DIODE
WIRING HARNESS
CLAMP
D28082
03M7184
14M7396
GDA10037
D28118
BOLT
M8 X 20
M8
LOCK NUT
WIRING HARNESS
BATTERY CABLE
BATTERY CABLE
BOLT
LOCK NUT
WET CHARGED BATTERY
HOLDER
HOOK BOLT
LOCK NUT
SEAT RELAY HARNESS
RELAY
MAIN CHASSIS
POSITIVE WITH BOOT
NEGATIVE WITH BOOT
M8 X 20
D28119
03M7184
14M7396
AM124356
GDU10204
D23047
14M7396
200302
102770
M8
M8 MAIN STARTER (KAWASAKI)
40
41
42
ISO MINI
963101
SCREW
12/24 SELF DRILLING
ELECTRICAL AND RELATED COMPONENTS - 59
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE AND CONTROL ASSEMBLY
CONSOLE AND CONTROL ASSEMBLY - 60
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE AND CONTROL ASSEMBLY
Ref. No.
1
Part No.
GDA10083
19M7785
14M7396
D14133
Description
CONSOLE
Qty.
1
5
7
2
2
1
1
4
16
1
1
4
4
2
2
6
2
2
2
2
2
4
1
2
1
1
1
2
8
2
2
2
8
2
2
1
4
1
1
1
2
2
2
Remarks
2
3
4
5
6
7
8
9
SCREW
M10 X 25
M8
LOCK NUT
CAP SCREW
LOCK NUT
BRACKET
BRACKET
SCREW
N10217
GDU10046
GDU10045
19M7867
14M7396
GDA10097
GDA10098
M44508
RH SEAT PLATE
LH SEAT PLATE
M8 X 25
LOCK NUT
PIVOT
M8
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
LH CONTROL
PIVOT
BUSHING
THRUST WASHER
ARM
BALL BEARING
WASHER
BOLT
LOCK NUT
CAP SCREW
EXTENSION SPRING
SCREW
M46676
GDU10253
AA34134
24M7388
03M7195
M85516
19H1936
GX10707
D14236
10 X 16 X 1 MM
M10 X 45
3/8" X 3/4"
14H778
NUT
PIVOT
BOLT
.190"
TCA13253
03M7184
M78480
GDA10081
GDA10080
D18093
03M7184
19H3693
TCU17400
D33002
24M7106
11M7082
TCA15322
GDA10136
J16931
M8 X 20
TIE BAND
CONTROL LEVER
CONTROL LEVER
GRIP
LH
RH
BOLT
SCREW
ROD
SWIVEL
M8 X 20
3/8" X 1 1/4"
CONTROL
ADJUSTER
10 X 18 X 2.500 MM
2.500 X 25 MM
WASHER
COTTER PIN
GAS OPERATED CYLINDER
BRACKET
PIN
D28255
D38146
14H1080
M63431
19M7867
E53830
ACCELERATOR
CABLE
CHOKE
3/8"
NUT
LOCK NUT
SCREW
M8 X 25
CLAMP
NOTES
CONSOLE AND CONTROL ASSEMBLY - 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDROSTATIC DRIVE SYSTEM COMPONENTS
Hydrostatic drive system Components - 62
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDROSTATIC DRIVE SYSTEM COMPONENTS
Ref.No. Part No.
Description
FITTING
Qty.
6
Remarks
1
2
D24028
BULK HOSE
BULK HOSE
BULK HOSE
BULK HOSE
BULK HOSE
BULK HOSE
CLAMP
FITTING
TEE FITTING
HOSE
AR
AR
AR
AR
AR
AR
12
4
2
2
2
4
(21") CASE RETURN, (MAKE FROM TY22503)
(5") CASE RETURN, (MAKE FROM TY22503)
(11-1/4") CASE RETURN, (MAKE FROM TY22503)
(11-1/4") CHARGE INLET, (MAKE FROM TY22503)
(5") CHARGE INLET, (MAKE FROM TY22503)
(29") CHARGE INLET, (MAKE FROM TY22503)
3
4
5
6
7
8
9
D18379
D14197
M86863
D28026
10
11
12
13
14
15
16
HIGH PRESSURE (SHORT)
HIGH PRESSURE (LONG)
GDA10089 HYDRAULIC HOSE
D24026
MT2119
200313
200312
D19000
FITTING
NUT
2
1
1
1
PATCH LOCK
PUMP
PUMP
HYDROSTATIC (BDP - 12) RH
HYDROSTATIC (BDP - 12) LH
SEAL KIT
17
18
19
20
21
GDA10022 DIPSTICK
1
1
2
1
TCA15373
D18207
HYDRAULIC RESERVOIR
KEY
GDA10137 OIL FILTER
GDA10100 WHEEL MOTOR
2
AZ45116
M78480
GASKET KIT
TIE BAND
1
4
NOTES
Hydrostatic drive system Components - 63
Download from Www.Somanuals.com. All Manuals Search And Download.
TRACTION DRIVE AND BRAKES
TRACTION DRIVE AND BRAKES - 64
Download from Www.Somanuals.com. All Manuals Search And Download.
TRACTION DRIVE AND BRAKES
Ref. No.
Part No.
Description
Qty.
Remarks
1
2
3
4
5
6
7
8
9
GDA10036
PIVOT
ARM
BUSHING
FITTING
1
1
2
1
1
1
1
3
6
1
1
1
2
2
2
1
1
4
1
1
2
1
1
8
8
3
5
2
2
10
2
1
6
6
1
1
4
2
2
1
1
2
4
2
1
2
2
8
8
2
2
1
1
1
1
2
2
2
3
1
2
2
2
D25059
D18076
D18205
D14104
IDLER
SNAP RING
WASHER
24H1441
GDA10032
03M7192
14M7518
19H1801
24H1305
D14010
19M8162
14M7152
14M7517
D18071
D28019
37M7059
200326
D25014
D23062
IDLER
BOLT
M10 X 30
M10
3/8" X 2"
FLANGE NUT
CAP SCREW
WASHER
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
13/32" X 13/16" X .065"
LOCK NUT
SCREW
NUT
M10 X 40
M10
M10
LOCK NUT
EXTENSION SPRING
LEVER
PARKING BRAKE
M5 X 12
SCREW
BRACKET
RETAINER
SPACER
Includes O-ring
RH BRAKE
D28099
D28100
PUSH PULL CABLE
PUSH PULL CABLE
CAP SCREW
WASHER
LH BRAKE
19H1900
24H1136
19M8319
H137328
19M8008
14M7151
TCU10037
GDA10000
GDU10096
03M7199
H137329
200312
5/16" X 3/4"
11/32" X 11/16" X .065"
SCREW
M8 X 50
LOCK NUT
CAP SCREW
NUT
M8 X 25
M8
NUT
12.700 MM
23 X 9.5 X 12
TIRE AND WHEEL ASSEMBLY
SUPPORT
BOLT
M12 X 35
M12
LOCK NUT
PUMP
PUMP
BOLT
RH HYDROSTATIC
LH HYDROSTATIC
M10 X 30
200313
03M7192
TCA15316
D18067
D25146
D25147
PULLEY
SHAFT KEY
ARM
RH PUMP
LH PUMP
ARM
PLATE
D13336
19H2975
34M5722
D28125
CAP SCREW
SPRING PIN
V-BELT
1/4" X 1-1/4"
5 X 30 MM
22H907
SET SCREW
5/16" X 7/8"
1/2" X 2-1/2"
PATCH LOCK
GDA10100
19H1930
H32811
MT2119
D18207
TCA15373
GDA10022
GDA10137
GDU10184
19M7785
D28029
D28088
24H1776
200330
200331
967387
967192
MOTOR
CAP SCREW
LOCK NUT
NUT
KEY
HYDRAULIC RESERVOIR
DIPSTICK
OIL FILTER
BRACKET
SCREW
BRAKE SHOE
BRAKE DRUM
WASHER
FAN SHIELD
DECK STOP BUSHING
CAP SCREW
WHIZ LOCKNUT
M10 X 25
5/16" X 47/64" X 065"
1/2-13 X 2.00
1/2-13
TRACTION DRIVE AND BRAKES - 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC SCHEMATIC
Hydraulic Schematic - 66
Download from Www.Somanuals.com. All Manuals Search And Download.
SEAT COMPONENTS
Ref. No.
Part No.
192068
181749
Description
SUSPENSION SEAT
KIT
Qty.
1
1
Remarks
1
SEAT ADJUSTER
181461
181074
24H1887
TCU17356
200324
ARM REST
SEAT SWITCH
WASHER
1
1
4
1
1
1
SINGLE SUSPENSION W/HDWR
2
3
4
11/32" X 1" X 0.134"
CUT TO LENGTH
PAD
SEAT PLATE (YELLOW)
BOLT
5
135139
1/2 X 1.06 X 3/8-16
6
7
8
9
10
11
12
13
14
15
16
17
K40003
03M7184
E83830
14M7396
M63277
14M7518
GDA10136
19M7786
181572
LOCK NUT
BOLT
CLAMP
1
1
3
1
4
4
1
4
1
4
2
2
M8 X 20
M8
LOCK NUT
LOCK NUT
FLANGE NUT
BRACKET
SCREW
SEAT BELT
FLAT WASHER
BOLT
M10
M10 X 30
RETRACTABLE MALE + FEM.
960703
960079
964025
LOCK NUT
Seat Components - 67
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME ASSEMBLY
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME ASSEMBLY
Ref. No.
Part No.
Description
Qty.
Remarks
1
2
3
4
5
6
7
8
9
200338
14M7396
E53830
GDU10222
03M7199
H137329
03M7197
JD7844
FRAME
LOCK NUT
CLAMP
PLATE
BOLT
1
1
1
1
4
8
4
2
2
2
2
1
1
7
1
21
3
1
1
2
1
1
2
M8
M12 X 35
M12 X 25
LOCK NUT
BOLT
LUBRICATION FITTING
PLATFORM
LOCK NUT
LOCK NUT
FENDER
FENDER
BOLT
BOLT
FLANGE NUT
SCREW
BUMPER
BUMPER
PLATE
BRACKET
BRACKET
TRACTION TAPE
200329
135139
964022
10
11
12
13
14
15
16
17
18A
18B
19
20
21
22
GDU10165
GDU10164
03M7017
03M7085
14M7518
19M7865
TCU20372
TCU20695
GDU10285
GDU10184
GDU10170
191257
LH
RH
M10 X 25
M10 X 30
M10
M8 X 16
KOHLER ENGINE
KAWASAKI ENGINE
* NOTE: See authorized servicing engine dealer for engines and engine related service items. Always reference the
engine model number when ordering parts.
NOTES
FRAME ASSEMBLY - 69
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT CASTER ASSEMBLY
FRONT CASTER ASSEMBLY - 70
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT CASTER ASSEMBLY
Ref. No.
Part No.
200334
Description
Qty.
1
2
2
1
1
1
1
1
Remarks
1
2
3
4
5
6
7
8
9
YOKE
CASTER
TCU14490
AA21840
TCU13871
TCA13769
19M7978
14M7276
TCU13454
E14625
ROUND RETAINER
BALL BEARING
SPACER
TIRE AND WHEEL ASSEMBLY
CAP SCREW
NUT
13" CASTER
M16
SPACER
SEAL
1
10
11
12
13
14
15
16
17
18
19
JD8933
145553
24H180
11M7083
A12188
TCU14490
JD7844
TCU13604
TCU15970
AM30795
BEARING CONE
BEARING CUP
WASHER
COTTER PIN
LOCK NUT
ROUND RETAINER
LUBRICATION FITTING
RIM
2
2
1
1
1
1
1
1
3.200 X 50 MM
13"
TIRE
TIRE VALVE STEM
1
1
13 X 5.00-5, 4 PLY
NOTES
FRONT CASTER ASSEMBLY - 71
Download from Www.Somanuals.com. All Manuals Search And Download.
ROPS
Ref. No.
Part No.
Description
Qty.
Remarks
1
TCA16051
ROPS
1
NOTES
ROPS - 72
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Notes - 73
Download from Www.Somanuals.com. All Manuals Search And Download.
SPINDLE ASSEMBLY
ꢀꢁ
ꢂ
ꢃ
ꢄ
ꢅ
ꢁ
ꢀꢀ
ꢀ
ꢆ
ꢇ
ꢅ
ꢈ
ꢀꢅ
ꢀꢆ
ꢀꢉ
SPINDLE ASSEMBLY - 74
Download from Www.Somanuals.com. All Manuals Search And Download.
SPINDLE ASSEMBLY
Ref. No.
Part No.
200041
200046
200042
200044
200043
200045
D13055
D18209
D18084
D18211
D13024
967347
Description
Spindle Assembly
Ball Bearing
Housing
Spacer
Qty.
1
2
1
1
1
3
3
3
3
3
3
3
18
9
3
3
3
Remarks
Includes items 2, 3, 4, 5, 6, 14
1
2
3
4
5
6
7
8
1.000 x 1.250 x 2.772
3/8-16
Shaft, Spindle
Bolt
Nut, Pulley (Special)
Pulley, Cutter Housing, 48" Deck
Pulley, Cutter Housing, 52" Deck
Pulley, Cutter Housing, 61" Deck
Spacer, Pulley
9
10
11
12
13
Bolt, Blade
Nut
5/8-18 x 7-3/4 HHCS
3/8-16 Std Hex GR5
960502
D18055
GDU10230
GDU10231
GDU10232
200047
Spacer, Blade Bolt
16.5" Blade, 48" Deck
18.0" Blade, 52" Deck
21.0" Blade, 61" Deck
Zerk, Grease S/O
14
3
NOTES
SPINDLE ASSEMBLY - 75
Download from Www.Somanuals.com. All Manuals Search And Download.
DECK LIFT ASSEMBLY
DECK LIFT ASSEMBLY - 76
Download from Www.Somanuals.com. All Manuals Search And Download.
DECK LIFT ASSEMBLY
Ref. No.
1
Part No.
TCU18697
Description
BEARING CAP
Qty.
Remarks
8
1
1
1
1
1
8
8
4
1
1
1
2
1
1
1
3
2
1
1
1
2
3
2
1
5
1
1
1
1
4
4
11
16
4
6
1
2
3
4
5
6
7
8
9
GDA10093
GDU10242
19M7796
H137327
GDA10092
19M7803
14M7396
JD7849
GDA10101
W10728
R58806
D18079
200339
ARM
PLATE
SCREW
M6 X 30
LOCK NUT
ARM
SCREW
M8 X 70
M8
LOCK NUT
LUBRICATION FITTING
LEVER
BUSHING
SNAP RING
GRIP
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
LEVER
LEVER
TCA15049
TCU17371
03M7204
TCU15816
D28155
TORSION SPRING
BOLT
M12 X 60
SPACER
PIN FASTENER
ROD
D25107
D23049
SWIVEL
NUT
14H1039
24H1111
11M7015
GDU10162
14H1058
GDU10238
TCU17245
24H1236
D28200
TCA13510
GDU10048
H137329
N10215
5/8"
WASHER
COTTER PIN
STUD
17/32" X 1-1/16" X .090"
3.200 X 25 MM
NUT
SWIVEL
SWIVEL
3/4"
WASHER
COMPRESSION SPRING
LINK CHAIN
U-BOLT
LOCK NUT
LOCK NUT
SCREW
13/16" X 2" X .149"
19M8162
24H1413
A15147
M10 X 40
WASHER
SPRING LOCKING PIN
57/64" X 1-3/8" X 0.048"
NOTES
DECK LIFT ASSEMBLY - 77
Download from Www.Somanuals.com. All Manuals Search And Download.
48" AND 52" CUTTING DECK
48" AND 52" CUTTING DECK - 78
Download from Www.Somanuals.com. All Manuals Search And Download.
48" AND 52" CUTTING DECK
Ref. No.
Part No.
GDA10104
GDA10088
D18209
D18084
D13024
D13055
200041
19M7786
E63526
D18055
Description
MOWER DECK
MOWER DECK
PULLEY
PULLEY
SPACER
NUT
Qty.
1
1
3
3
3
3
3
18
18
9
3
3
3
3
2
1
1
1
4
1
1
1
1
2
1
1
4
3
2
2
2
2
2
2
2
2
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
Remarks
1
48"
52"
2
CUTTER HOUSING 48"
CUTTER HOUSING 52"
3
4
5
6
7
8
9
10
11
SPINDLE
BOLT
Nut
SPACER
BOLT
NUT
BLADE
BLADE
BUSHING
STRAP
V-BELT
V-BELT
WHEEL
COVER
COVER
COVER
COVER
KNOB
ARM
M10 X 1.5 X30 HHFCS
M10 X 438 HHSFN
967347
5/8-11 X 2.25
5/8"
48" HIGH LIFT
52" HIGH LIFT
14H1083
GDU10230
GDU10231
TCU14540
GDU10119
TCU16092
TCU16093
TCU18744
GDU10251
GDU10249
GDU10252
GDU10250
M119352
GDA10084
GDA10085
D18076
12
13
14
ENGINE TO BLADES 48"
ENGINE TO BLADES 52"
15
16
GAGE
LH 48"
LH 52"
RH 48"
RH 52"
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
LH
RH
ARM
BUSHING
LUBRICATION FITTING
SCREW
LOCK NUT
PIN FASTENER
BOLT
JD7844
19H2380
D24008
1/4" X 1"
TCA13292
03M7185
14M7396
GDA10103
03H1729
H122207
TCA15346
D18032
03H1658
24H1305
K40003
03H1836
AM127235
M132768
H141123
03H2040
D13005
D23058
D28025
D14010
N10215
TCA14548
GDU10180
03H1838
D28050
GDU10181
D24040
M8 X 25
M8
LOCK NUT
PIVOT
BOLT
1/4" X 1
FLANGE NUT
ARM
PULLEY
BOLT
3/8" X 2-1/4"
13/32" X 13/16" X .065"
WASHER
LOCK NUT
BOLT
3/8" X 3-1/2"
CHUTE
TORSION SPRING
PUSH NUT
BOLT
HOOK BOLT
HOOK BOLT
SPRING
LOCK NUT
LOCK NUT
PULLEY
SPACER
BOLT
48"
52"
42
43
44
45
46
47
48
49
50
51
3/8" X 5"
IDLER
SPACER
BOLT
E62934
FLANGE NUT
48" AND 52" CUTTING DECK - 79
Download from Www.Somanuals.com. All Manuals Search And Download.
61" CUTTING DECK
61" CUTTING Deck - 80
Download from Www.Somanuals.com. All Manuals Search And Download.
61" CUTTING DECK
Ref. No.
1
Part No.
GDA10077
D18211
D13024
D13055
200041
19M7786
E63526
D18055
967347
14H1083
GDU10232
TCU14540
GDU10119
E62934
TCU18744
D24040
GDU10187
M119352
GDA10084
GDA10085
D18076
Description
MOWER DECK
Qty.
Remarks
1
3
3
3
3
18
18
9
3
3
3
2
1
4
6
4
1
2
1
1
4
3
2
2
2
2
2
2
2
2
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
61"
2
3
4
5
6
7
8
9
PULLEY
SPACER
NUT
SPINDLE
BOLT
NUT
SPACER
BOLT
NUT
BLADE
BUSHING
STRAP
CUTTER HOUSING 61"
M10 X 1.5 X30 HHFCS
M10 X 438 HHSFN
5/8-11 X 2.25
5/8"
61" HIGH LIFT
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
FLANGE NUT
WHEEL
GAGE
LH 61"
BOLT
COVER
KNOB
ARM
LH
RH
ARM
BUSHING
LUBRICATION FITTING
SCREW
LOCK NUT
PIN FASTENER
BOLT
JD7844
19H2380
D24008
1/4" X 1"
TCA13292
03M7185
14M7396
GDA10103
03H1729
H122207
TCA15346
D18032
03H1658
24H1305
K40003
03H1836
AM127488
M132768
H141123
03H2040
D23058
D28025
D14010
N10215
TCA14548
GDU10180
03H1838
D28050
M8 X 25
M8
LOCK NUT
PIVOT
BOLT
1/4" X 1
FLANGE NUT
ARM
PULLEY
BOLT
3/8" X 2-1/4"
13/32" X 13/16" X .065"
WASHER
LOCK NUT
BOLT
3/8" X 3-1/2"
CHUTE
TORSION SPRING
PUSH NUT
BOLT
HOOK BOLT
SPRING
LOCK NUT
LOCK NUT
PULLEY
SPACER
BOLT
61"
3/8" X 5"
IDLER
SPACER
GDU10181
61" CUTTING Deck - 81
Download from Www.Somanuals.com. All Manuals Search And Download.
LABELS
61" CUTTING DECK
61" CUTTING Deck - 82
Download from Www.Somanuals.com. All Manuals Search And Download.
LABELS
Ref. No.
1
Part No.
181023
D28167
D28181
GDU10254
200343
GDU10256
GDU10257
GDU10258
GDU10259
GDU10260
GDU10262
GDU10267
GDU10268
GDU10269
M17554
Description
Decal
Decal
Decal
Qty.
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
4
4
4
1
1
1
4
1
Remarks
HYDRO OIL SPECS.
THROTTLE CONSOLE
NO STEP
2
3
4
5
6
7
8
9
Decal
CHARIOT
BRUTUS
PUPPY PAW
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
LABEL
GREAT DANE BLACK
GREAT DANE WHITE
MOTION CONTROL OTL KIT
MOTION CONTROL CONSOLE
BELT PATH 48", 52", 61" DECK
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
WARNING - HOT SURFACES
IGNITION
DANGER BLADE CONTACT
DANGER THROWN OBJECTS
DISCHARGE
M127610
M131739
M131748
M137637
TCU51051
TCU14840
TCU14862
TCU13514
TCU13515
TCU20576
TCU14885
TCU15908
TCU151051
TCU20575
TCU15907
DANGER, ROTATING BLADES
GENERAL CAUTION
PARK BRAKE DIRECTION
ROPS WARNING - ENGLISH
ROPS WARNING - SPANISH
ROPS CERTIFICATION - SPANISH
DANGER, EXPLOSIVE GASES/POISON
CUT HEIGHT
DANGER, ROTATING BELTS
ROPS CERTIFICTATION
WARNING SLOPE
NOTES
LABELS - 83
Download from Www.Somanuals.com. All Manuals Search And Download.
LABELS - 84
Download from Www.Somanuals.com. All Manuals Search And Download.
|