Owner's Manual
®
42-inch Universal
Tow Behind
POWER MOWER
Model No. 486.243292
• Safety
CAUTION:
• Assembly
• Operation
• Maintenance
• Parts
Before using this product, read
this manual and follow all
Safety Rules and
Operating Instructions.
IMPORTANT - READ THIS FIRST!!!
For Missing Parts or Assembly Questions
Please Call 866-576-8388
Mon.-Fri. 7 am - 5 pm CST.
FAX 217-728-2032 or e-mail [email protected]
Missing parts will be sent UPS in 24 hours directly to your home.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
FORM NO. 48839 (REV. 8/04)
PRINTED IN U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES
Safe Operation Practices for Tow Behind Mowers
WARNING: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to
observe the following safety instructions could result in serious injury or death.
I. GENERAL OPERATION
•
•
•
Keep your eyes and mind on your mower and the
area being cut. Do not let other interests distract
you.
Do not put hands or feet near or under rotating
parts. Keep clear of the discharge opening at all
times.
Before cleaning, inspecting, or repairing your
mower, stop the engine and make absolutely sure
the blade and all moving parts have stopped. Then
disconnect the spark plug wire and keep it away
from the spark plug to prevent accidental starting.
Do not operate your mower if it vibrates
abnormally. Excessive vibration is and indication of
damage; stop the engine, safely check for the
cause of vibration and repair as required.
Never operate your mower without proper guards,
plates or other safety devices in place.
•
•
Read, understand and follow all instructions in the
manual and on the machine before starting.
Read this operator's manual carefully. Become
familiar with the controls and know how to operate
your mower properly.
•
•
Only allow responsible adults who are familiar with
the instructions to operate the machine.
Clear the area of objects such as rocks, toys, wire,
etc., which could be picked up and thrown by the
blade.
•
•
•
Be sure the area is clear of other people before
mowing. Stop machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely
necessary. Always look down and behind before
and during backing.
•
•
•
Be aware of the mower discharge direction and do
not point it at anyone. Do not operate the mower
without the guard in place.
Slow down before turning.
Never leave a running machine unattended. Always
turn off blades and stop engine.
II. SLOPE OPERATION
Slopes are a major factor related to loss-of-control and
tip-over accidents, which can result in severe injury or
death. All slopes require extra caution. If you feel
uneasy on it, do not mow it.
•
•
•
•
•
Turn off blades when not mowing.
Mow only in daylight or good artificial light.
Do not operate the machine while under the
influence of alcohol or drugs.
Watch for traffic when crossing or operating near
roadways.
Use extra care when loading or unloading the
machine into a trailer or truck.
Do not attempt to operate your tractor or mower
when not in drivers seat.
Disengage power to mower and stop engine when
transporting or when not in use.
Exercise special care when mowing around fixed
objects in order to prevent the blades from striking
them. Never deliberately run tractor or mower onto
or over any foreign object.
Use mower only as the manufacturer intended and
as described in this manual.
Do not operate mower if it has been dropped or
damaged in any manner. Always have damage
repaired before using your mower.
DO:
•
•
Mow up and down slopes, not across.
Remove obstacles such as rocks, tree limbs, etc.
Watch for holes, ruts or bumps. Uneven terrain
could overturn the machine. Tall grass can hide
obstacles.
Use slow speed. Choose a low gear so that you will
not have to stop or shift while on the slope.
Follow the manufacturer's recommendations for
wheel weights or counterweights to improve
stability.
Keep all movement on the slopes slow and gradual.
Do not make sudden changes in speed or direction.
Avoid starting or stopping on a slope. If tires lose
traction, disengage the blades and proceed slowly
straight down the slope.
•
•
•
•
•
•
•
•
•
•
•
DO NOT:
•
•
Do not turn on slopes unless necessary, and then
•
•
Always wear safety glasses or eye shields when
starting and while using your mower.
Dress properly. Do not operate mower when
barefoot or wearing open sandals. Wear only solid
shoes with good traction when mowing.
Always make cutting height adjustments before
starting your mower. Never attempt to do this while
the engine is running.
turn slowly and gradually downhill, if possible.
Do not mow near drop-offs, ditches or
embankments. The mower could suddenly turn
over if a wheel is over the edge of a cliff or ditch, or
if an edge caves in.
•
•
Do not mow on wet grass. Reduced traction could
cause sliding.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
III. CHILDREN
Look for this symbol to point out
important safety precautions. It
means CAUTION!!! BECOME
ALERT!!! YOUR SAFETY IS
INVOLVED.
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Never assume
that children will remain where you last saw them.
•
•
•
•
Keep children out of the mowing area and under
the watchful care of another responsible adult.
Be alert and turn machine off if children enter the
area.
Before and when backing, look behind and down
for small children.
Never carry children. They may fall off and be
seriously injured or interfere with safe machine
operation.
CAUTION: Always disconnect spark
plug wire and place wire where it
cannot contact spark plug in order to
prevent accidental starting when
setting up, transporting, adjusting or
making repairs.
•
•
Never allow children to operate the machine.
Use extra care when approaching blind corners,
shrubs, trees or other objects that may obscure
vision.
IV. SERVICE
•
Use extra care in handling gasoline and other fuels.
They are flammable and vapors are explosive.
•
•
Use only an approved container.
Never remove gas cap or add fuel with the
engine running.
•
Allow engine to cool before refueling. Do not
smoke near or while operating mower.
Never refuel the machine indoors.
Never store the machine or fuel container inside
a room where there is an open flame, such as
with a gas water heater.
•
•
•
•
Never run a machine inside a closed area.
Keep nuts and bolts, especially blade attachment
nuts, tight and keep equipment in good condition.
Never tamper with safety devices. Check their
proper operation regularly.
Keep machine free of grass, leaves or other debris
build-up. Clean oil or fuel spillage. Allow machine to
cool before storing.
•
•
•
•
•
Stop and inspect the equipment if you strike an
object. Repair, if necessary, before restarting.
Never make adjustment or repairs with the engine
running.
Mower blades are sharp and can cut. Wrap the
blade(s) or wear gloves, and use extra caution
when servicing them.
•
Check brake operation frequently. Adjust and
service as required.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
REMOVING UNIT FROM CRATE
•
•
•
Assemble a 3/8 Flat Washer onto a 3/8-16 x 2-1/2
Hex Bolt.
•
•
Remove top boards.
Remove two Bolts from front of crate which hold
shipping anchors.
Remove two Bolts from bottom at rear of crate
which hold shipping anchors.
Remove Hitch Assembly and Parts Bag from crate.
Remove Roller Bolt from Front Roller, Remove
shipping anchors and reinstall Roller Bolt.
Remove Nuts from Height Adjustment Straps and
remove shipping anchors from each side of mower.
Reinstall Nuts to Height Adjustment Straps, then
loosen 1/4 turn to allow straps to pivot freely.
Check all loose parts and bag contents against
Crate Contents and Bag Contents illustration on
page 5. If any part is missing or damaged contact
the store where you purchased the unit.
Insert Bolt and Washer through slot of Rear
Quadrant and hole in Towbar Tube.
Secure tightly with 3/8-16 Lock Nut then loosen Nut
1/4 turn to allow tube to pivot freely inside Rear
Quadrant.
•
•
•
NOTE: Towbar Tube must pivot freely inside Rear
Quadrant when latch is pulled from notch.
•
INSTALL CLUTCH CABLE AND WIRE
HARNESS TO TOWBAR TUBE.
•
•
•
Unwrap the Wire Harness and the Clutch Cable
from around the Engine.
Lay the Clutch Cable along the left side of the
Towbar Tube and lay the Wire Harness along the
right side of the Towbar Tube.
Install three 3/8" Cable Clips on the Clutch Cable
and three 1/2" Cable Clips onto the Wire Harness.
Align all six Cable Clips with the holes in the Towbar
Tube and secure them with three #10 Self-Tapping
Screws.
CAUTION: Before starting to
assemble mower, remove spark plug
wire from plug of mower engine.
•
•
OPERATOR ORIENTATION
INSTALL CLUTCH CABLE TO THE HITCH
ASSEMBLY
When right and left are mentioned in this manual, it
means your right and your left when you are seated
behind the wheel in the operating position.
•
•
Remove the 1/4" Lock Nut and 1/4" x 3/4" Bolt from
the Clutch Cable Eyelet.
ENGINE OIL
Screw one 5/16" Nut off the Clutch Cable Housing
and onto the bare cable wire. Screw the second
5/16" Nut all the way onto the Clutch Cable Hous-
ing. Insert the Clutch Cable Eyelet through the
slotted hole in the Cable Anchor on the Hitch
Assembly.
VERY IMPORTANT:
Engine must be filled with oil before operation. See OIL
& FUEL RECOMMENDATIONS in engine Owner's
Manual for correct filling instructions and oil fill capacity.
NOTE: The loose 5/16" Nut on the cable wire must be
cocked at an angle to fit through the slotted hole.
INSTALL TOWBAR TUBE TO REAR
QUADRANT
•
Fasten the Clutch Cable Eyelet to the Clutch Lever,
reusing the 1/4" x 3/4" Hex Bolt and 1/4" Lock Nut.
Tighten the 1/4" Lock Nut securely and then loosen
approximately two turns to allow the cable to pivot
freely on the bolt.
•
Cut and remove the Plastic Tie which holds the Wire
Harness and the Clutch Cable to the Rear
Quadrant. (See Fig. 1)
•
•
•
Remove two 3/8 Bolts, two 3/8 Lock Nuts and one
3/8 Flat Washer from the rear of the Towbar Tube.
Place tube into Rear Quadrant, align holes, insert
3/8-16 x 2-1/2 Hex Bolt through rear hole of tube.
Secure tightly with 3/8-16 Lock Nut then loosen Nut
1/4 turn to allow tube to pivot freely inside Rear
Quadrant.
•
Screw the loose 5/16" Nut back onto the Clutch
Cable Housing. Use the 5/16" Nuts to adjust the
cable to the proper tension.
VERY IMPORTANT
See DRIVE TENSION on page 16 in the SERVICE AND
ADJUSTMENTS Section of this manual for proper
Clutch Cable adjustment.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
I
O
•
•
•
•
•
Insert the ON/OFF Switch up through the Switch
Mounting Bracket and secure it by reinstalling the
Ring Nut.
FIG. 1
NOTE: The notch in the threads of the ON/OFF Switch
must face toward the "ON" of the ON/OFF Switch Decal
to insure proper ON/OFF control.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING DIAGRAM
SAFETY SEAT
AUTOMATIC GROUND
COUPLER
BLUE WIRE FROM MAGNETO GROUND
TO LOWER SPADE ON SWITCH
SAFETY SWITCH
(NORMALLY OPEN)
BLACK WIRE (A)
FROM MODULE TO SWITCH
(UPPER SPADE)
SWITCH
BLACK WIRE(D)
FROM MODULE TO SWITCH
(UPPER SPADE)
BLACK WIRE (E)
FROM MODULE TO
ENGINE GROUND
RED WIRE
RED WIRE (F) FROM MODULE
TO MAGNETO GROUND
FROM ON/OFF SWITCH
TO MAGNETO GROUND
ELECTRONIC CONTROL
MODULE
BLUE WIRE FROM SAFETY SEAT
TO LOWER SPADE OF SWITCH
ENGINE
BLACK WIRE
FROM ON/OFF SWITCH
TO ENGINE GROUND
SWITCH
ENGINE ON/OFF
OIL
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
FIG. 2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION:
Never operate the mower without discharge
chute cover in its proper place.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: Avoid prolonged mowing of ditches with
slopes greater than 15 degrees. Small engines become
starved for oil at angles greater than 15 degrees and
should only be used for brief periods on such slopes. Be
sure the engine is tilled to the maximum oil level when
mowing on slopes.
•
Mowing should be started with tractor in low gear
and speed increased only as mowing conditions will
safely permit.
•
•
Mower will perform at its best when engine throttle is
set for full throttle.
You will obtain better mowing results in grassy areas
if they are mowed when the grass is approximately
4" to 5" maximum height. While your mower will cut
grass taller than 5", you will notice a substantial
increase in engine power required and some change
in the finished appearance of the area mowed.
Mowing conditions will vary from place to place,
including the types of grass which are being
mowed, such as fine stalk, coarse stalk, and
dense or sparse grasses. When mowing tall grass
you may find that certain grasses may be pressed
downward under the wheels so that they will not
mow properly. If this condition exists you may have
to mow the area twice, the first mowing with the
mower raised and the second mowing at the
desired height. If it is practical, you will achieve
better results if the second mowing is at right
angle to the previous mowing.
•
•
•
Do not mow grass when it is wet. Wet grass will
plug mower and leave undesirable clumps. Allow
grass to dry before mowing.
Always operate mower engine at full throttle when
mowing to assure better mowing performance and
proper discharge of material. Regulate ground
speed by selecting a gear low enough to give the
best cutting performance and quality of cut.
When operating any attachment, select a ground
speed that will suit the terrain and give the best
performance for the attachment being used.
When mowing slopes, always mow them up and
down at slow speed. Never mow across slopes.
Refer to Slope Operation on page 3 and to the
Slope Guide on page 23.
•
•
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
ENGINE MAINTENANCE
Refer to engine manual when performing
maintenance on engine.
LUBRICATION
IMPORTANT: Do not oil or grease pivot points.
Viscous lubricants will attract dust and dirt that can
cause wear on pivot points. If you feel they must be
lubricated, use only a dry powdered graphite type
lubricant.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
When grinding, take care to maintain blade balance.
Check blade for proper balance before reinstalling
to mower.
To check and balance blade use a balancing
machine or, fixture as shown in figure 8. File mate-
rial off heavier end of blade until it is balanced.
CLEANING THE MOWER
CAUTION: Disconnect spark plug wire
from spark plug before working on under-
side of mower.
•
•
•
Clean the underside of your mower to remove build-
up of grass clippings.
Clean any gasoline, oil, or foreign matter from
engine, painted surfaces and wheels.
We do not recommend using a garden hose to
clean mower unless the electrical system, muffler,
air filter and carburetor are covered to keep water
out. Water in engine can result in shortening engine
life.
BLADE CARE
•
For best results, mower blade must be kept sharp.
The blades can be sharpened with a few strokes of
a file or on a grinding wheel. Do not attempt to
sharpen blades while blades are on mower.
•
To remove blade for sharpening, use wooden block
to hold blade while removing the blade mounting
nut. The nuts have right hand threads. (See Fig. 7.)
CAUTION: Do not handle mower blades
with bare hands. Careless or improper
handling may result in serious injury.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
REPAIR PARTS
CHECKING DRIVE TENSION
Your rotary mower has been produced with components
designed for your unit. Although standard V-belts,
bearings, blades pulleys etc. may look like the parts
used on your rotary mower, many are of a different
construction and could in some cases cause the mower
to malfunction.
•
•
Remove V-belt cover from right side of unit.
Place Blade Control Lever in the "ENGAGED"
position.
Check tension spring length. It should be 5-3/8" to
5-5/8" over the coils of the Spring Body. See Fig. 9.
•
ADJUSTING DRIVE TENSION
For continued satisfactory performance, use only repair
parts supplied by the manufacturer. See you Sears
Service Center for replacement parts.
To Increase Drive Spring Tension
•
Place blade clutch lever in the "DISENGAGED"
position.
Loosen the inner nut of the clutch cable.
Tighten the outer nut to increase spring tension.
CAUTION: Disconnect spark plug wire
from spark plug before replacing V-belt.
NOTE: For every 1/8" adjustment made to the cable
you will get approximately 1/8" movement on the
tension spring.
To Decrease Drive Spring Tension
•
Place blade clutch lever in the "DISENGAGED"
position.
•
•
Loosen the outer nut of the clutch cable.
Tighten the inner nut to decrease spring tension.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
CAUTION: Disconnect spark plug wire
from spark plug before working on under-
side of mower.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
19
Download from Www.Somanuals.com. All Manuals Search And Download.
42" TOW BEHIND MOWER - MODEL NO. 486.243292
,
20
Download from Www.Somanuals.com. All Manuals Search And Download.
42" TOW BEHIND MOWER - MODEL NO. 486.243292
Item
No.
Qty.
Req.
Item
No.
Qty.
Req.
Part No.
Description
Part No.
Description
1.
2.
3.
4.
5.
6.
7.
8.
HA23834
HA23598
49112
43081*
43064*
HA23519
HA23516
HA23246
HA124634*
HA20129
HA23193
HA22981
HA64064
HA22987
HA120389
HA23518
43262*
HA22948
47134
44180
HA23196
HA23258
HA15015
HA6979
41576*
HA23197
43082*
HA17322
HA9411666*
43648*
Mower Deck Pan ........................................ 1
Rod- Deflector Mounting ............................ 1
Pulley (included with item 41) .................... 2
Washer, 3/8" x 7/8" x .08" .......................... 3
Nut - 5/16-18 Hex Lock .............................. 8
Hitch Assembly .......................................... 1
Mower Blade .............................................. 2
Belleville Washer ....................................... 2
Nut, 9/16-18 Hex ........................................ 2
Flat Washer ................................................ 2
Screw, 3/8-16 x 1-1/4 Thread Forming .... 25
Belt Guide .................................................. 4
Brake Spring Assembly.............................. 1
Brake Rod .................................................. 1
Washer, 1/2" x 1-1/4" x .083" ..................... 2
Clutch Bellcrank ......................................... 1
Nut, 1/2-13 Hex Lock ................................. 6
Brake Release Rod .................................... 1
Hair Cotter Pin ........................................... 5
Bolt, 5/16-18 x 2" Hex Head Grade 5 ........ 3
Idler Tension Spring ................................... 1
Idler Bracket ............................................... 1
Idler Pulley ................................................. 1
Flat Washer ................................................ 8
Bolt, 3/8-16 x 1-3/4" Hex Head.................. 1
Interlock Bracket ........................................ 1
Nut, 3/8-16 Hex Lock ................................. 4
Interlock Switch .......................................... 1
Screw, #10-16 x 1/2" Self Tapping............. 6
Bolt, 1/4-20 x 1-1/2" Hex Head.................. 1
Nut, 1/4-20 Hex Lock ................................. 8
Extension Spring ........................................ 1
Clutch Cable............................................... 1
Module Connector...................................... 1
Module........................................................ 1
67.
68.
69.
70.
71.
72.
73.
74.
75.
76.
77.
78.
79.
80.
81.
82.
83.
84.
85.
86.
87.
88.
89.
90.
91.
92.
93.
94.
95.
96.
97.
98.
99.
HA23526
48840
Hitch Tube ................................................. 1
Self Tapping Screw ................................... 8
Danger Decal ............................................ 1
Left Hand Wheel Mounting Bracket.......... 1
Right Hand Wheel Mounting Bracket ....... 1
Cotter Pin .................................................. 8
Clevis Pin .................................................. 2
Wheel ........................................................ 2
Flat Washer, 13/16" x 1-1/2" x .134"......... 2
Flat Washer ............................................... 2
Hub Cap .................................................... 2
Height Adjustment Strap ........................... 2
Cotter Pin, 3/32" x 3/4" ............................. 1
Strap, Latch ............................................... 2
Spring, Latch ............................................. 2
Clip - Hose/Cable 1/2" .............................. 3
Clip - Hose/Cable 3/8" .............................. 3
Lever - Clutch ............................................ 1
Washer, 13/32" x 1-3/16" x 3/16" .............. 2
Bolt, 3/8-16 x 1-1/2" Hex Head................. 1
Spring ........................................................ 1
Bolt, 1/4-20 x 3/4" Hex Head.................... 2
Wire ........................................................... 1
Operator's Presence Seat ........................ 1
Cord Clip ................................................... 2
Washer, 1/4" Std. ...................................... 4
Grip - Handle ............................................. 2
Bolt, 7/16-20 x 1-1/4" Hex Head............... 1
Washer, 1" x 13/16" Thick ......................... 2
Washer, 1.59" x 1.032" x .06" ................... 1
Washer, 1/2" x 1-1/4" x .083" .................... 3
Tank, Gasoline .......................................... 1
Cap, Gasoline Tank................................... 1
Fuel Line ................................................... 1
Clamp, Fuel Line ....................................... 2
Cover, Gas Tank ....................................... 1
Bracket, Tank Mounting ............................ 2
Screw, 1/4" x 1-1/4" Self Tapping ............. 4
Bolt, Hex 5/16-18 x 3/4" ............................ 4
Owner's Manual
HA12314
HA22996
HA22997
714-0121
HA23638
47081
HA456151
HA23263
HA23229
HA23646
44101*
HA24441
HA20186
HA23760
HA23761
HA23527
HA15200
43062*
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41
HA19445
43012*
HA23832
HA23586
HA11947
43088
47707
HA181668*
HA4143
43601
HA120389
HA23732
HA23733
43013*
HA3293
HA24617
HA23253
HA23252
45040*
736-0722*
712-0121*
HA23513
100. 48837
101. HA23792
Screw, #10-24 x 1/2" Pan Head................ 2 102. 25051
Washer, #10 Med. Lock ............................. 2
Nut, #10-24 Hex ......................................... 2
Engine Mounting Plate............................... 1
103. 25052
104. 48795
105. 43182
212702-0114-E1 8 HP Engine ............................................... 1
64675
NP
48839
Spindle Assembly (see page 22) ............... 2
Pulley.......................................................... 1
Set Screw, 5/16-18 x 5/16" Socket Hd. ..... 2
Square Key ................................................ 1
Danger Decal ............................................. 2
Danger Decal ............................................. 2
V-Belt .......................................................... 1
Bolt, 3/8-16 x 1" Hex Head........................ 1
Rubber Grommet ....................................... 1
Clevis Pin ................................................... 2
Towbar Assembly ....................................... 1
Hitch Pin ..................................................... 1
Hair Cotter Pin ........................................... 1
On/Off Switch ............................................. 1
Decal - Engine Shut Off ............................. 1
Clutch Lever Decal..................................... 1
Wire Harness ............................................. 1
Deflector ..................................................... 1
Decal - Operation ....................................... 1
Mower Roller .............................................. 1
Bolt, 1/2-13 x 7" Hex Head....................... 1
Nut, Special (included with item 41) .......... 2
Bolt, 3/8-16 x 2-1/2" Hex Head.................. 4
Deflector Spring ......................................... 1
Sears Logo Decal ...................................... 1
Belt Cover .................................................. 2
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
66.
HA22994
HA115321*
HA3073
HA17285
HA12315
HA22980
43001*
HA19484
HA23636
HA23644
HA20988
714-0117
45084
HA23262
HA23647
HA23612
HA23597
HA23755
HA12138
HA126145*
49110
*Standard Hardware - Purchased Locally
43432*
HA12988
44059
HA23645
21
Download from Www.Somanuals.com. All Manuals Search And Download.
42" TOW BEHIND MOWER - MODEL NO. 486.243292
Item
Qty.
No. Part No.
Description
Req.
1-6 64675
Spindle Assembly ..................... 1
Nut, 9/16-18 Special ................ 1
Pulley ........................................ 1
Jackshaft .................................. 1
Spacer ...................................... 1
Housing & Bearing Assembly ... 1
Blade Adapter ........................... 1
Mower Blade............................. 1
Belleville Washer ...................... 1
Thrust Washer .......................... 1
Nut, 9/16-18.............................. 1
1.
2.
3.
4.
5.
6.
7.
8.
9.
49110
49112
49109
49111
HA23242
HA23245
HA23516
HA23246
HA20129
10. HA124634
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SLOPE GUIDE
(Keep this sheet in a safe place for future reference.)
Use this guide to determine if a slope is safe for the operation of your tractor and TOW
BEHIND MOWER. Refer also to the instructions in your vehicle owners manual.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Get it fixed, at your home or ours!
For repair of major brand appliances in your own home…
no matter who made it, no matter who sold it!
1-800-4-MY-HOMESM Anytime, day or night
(1-800-469-4663)
To bring in products such as vacuums, lawn equipment and electronics
Sears Parts & Repair Center.
for repair, call for the location of your nearest
1-800-488-1222 Anytime, day or night
For the replacement parts, accessories and owner’s manuals
that you need to do-it-yourself, call Sears PartsDirectSM
!
1-800-366-PART 6 a.m. – 11 p.m. CST,
(1-800-366-7278)
7 days a week
To purchase or inquire about a Sears Service Agreement:
1-800-827-6655
7 a.m. – 5 p.m. CST, Mon. – Sat.
Para pedir servicio de reparación a domicilio,
y para ordenar piezas con entrega a domicilio:
Au Canada pour service en français:
SM
1-877-LE-FOYER
SM
1-888-SU-HOGAR
(1-877-533-6937)
(1-888-784-6427)
SM
HomeCentral
® Registered Trademark / ™ Trademark of Sears, Roebuck and Co.
® Marca Registrada / ™ Marca de Fábrica de Sears, Roebuck and Co.
© Sears, Roebuck and Co.
Download from Www.Somanuals.com. All Manuals Search And Download.
|