Agri Fab Lawn Mower 45 0438 User Manual
2008-01  
Illustrated  
Parts List  
I0807220  
531 30 83-24  
40 Inch Front Mount Dethatcher  
(45-0438)  
Repair Parts Manual  
Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment.  
Exercise caution at all times, when using power equipment.  
•
•
•
Read safety rules in the vehicle owners manual and  
know how to operate your equipment, before using the  
tine dethatcher.  
Never operate vehicle and tine dethatcher attachment  
without wearing substantial footwear, and do not allow  
anyone to ride or sit on the tine dethatcher.  
Never allow children to operate the tractor or  
dethatcherattachment,anddonotallowadultstooperate  
without proper instructions.  
•
•
When de-thatching do not drive too close to a creek or  
ditch and be alert for holes and other hazards which  
could cause you to lose control of the vehicle.  
Before operating vehicle on any grade (hill) refer to the  
safetyrulesinthevehicleownersmanualconcerningsafe  
operation on slopes. STAY OFF STEEP SLOPES.  
This equipment is not meant for street or highway use.  
Watch for traffic when de-thatching near highways.  
Vehicle and attachments should be stopped and  
inspected for damage after striking a foreign object.  
Check all nuts, bolts and screws frequently making sure  
they are tight and the equipment is in safe  
•
•
•
•
Eye Protection should be worn when operating the tine  
dethatcher.  
•
Always begin with transmission in first (low) gear,  
and gradually increase speed as conditions permit.  
Recommended maximum operating speed is 3 M.P.H.  
Always stop vehicle and lift dethatcher to transport  
position before making short turns.  
working condition.  
Follow the maintenance instructions as outlined in this  
owners manual.  
•
•
Lookforthissymboltopointoutimportantsafetyprecautions.Itmeans—Attention!!Become  
alert!! Your safety is involved.  
1/2”  
9/16”  
2
6
1
2
3
4
5
7
8
10  
12  
11  
9
REF PART NO. QTY DEsCRIPTION  
REF PART NO. QTY DEsCRIPTION  
1
2
3
4
5
6
44326  
43063  
43001  
43087  
43069  
12  
2
4
2
4
Carriage Bolt, 5/16-18 x 1"  
Hex Bolt, 5/16-18 x 1"  
Hex Bolt, 3/8-16 x 1"  
Hex Bolt, 3/8-16 x 1-1/4"  
Carriage Bolt, 3/8-16 x 1-1/2"  
Flat Washer, 5/8"  
7
8
9
10  
11  
12  
43343  
46838  
44044  
43055  
47810  
6
4
1
1
14  
10  
Hairpin Cotter, 1/8"  
Spacer, .8" x 1" x .5"  
Clevis Pin, 3/8" x 3/4"  
Hairpin Cotter, 3/32"  
Nylock Nut, 5/16-18  
Nylock Nut, 3/8-16  
R19212113  
4
HA21362  
17  
15  
14  
16  
13  
18  
22  
21  
23  
19  
20  
26  
25  
27  
24  
REF PART NO. QTY DEsCRIPTION  
REF PART NO. QTY DEsCRIPTION  
13  
14  
15  
16  
17  
18  
19  
20  
24876  
23668  
62600  
23666  
62601  
43943  
26168  
26043  
2
1
1
2
1
1
1
1
Mounting Arm  
Axle Bushing  
Lift Handle  
Angle Mount Bracket  
Lift Handle Bracket  
Plastic Grip  
21  
22  
23  
24  
25  
26  
27  
24043  
23673  
24874  
44148  
23676  
44213  
26044  
1
1
1
1
2
1
1
Lift Handle Arm  
Handle Lock Bracket  
Tine Shield  
Axle  
Keeper Plate  
Wheel  
Hitch Plate  
Mounting Shaft  
Frame Mount Bracket  
3
•
•
Remove any front mounted attachments which may  
be installed on your tractor.  
Stop engine and let muffler cool before  
attempting to install dethatcher hitch  
brackets.  
Mark all loose parts and save for reassembly.  
1
1
LEFT END  
17  
17  
1
23  
x 1  
x 2  
TINES POINT  
TO FRONT  
11  
x 2  
11  
2
23  
16  
1
16  
11  
x 2  
x 4  
1
x 4  
11  
3
13  
14  
4
14  
1
11  
x 1  
1
x 4  
x 2  
11  
12  
x 4  
12  
x 2  
4
13  
x 2  
4
4
26  
7
APPLY OIL  
24  
6
x 1  
x 1  
6
7
26  
24  
x 1  
x 2  
5
6
7
7
6
x 2  
x 1  
6
7
20  
x 1  
20  
7
x 2  
5
ATTACHING DETHATCHER TO TRACTOR  
7
•
If the front of your tractor has front mounting holes as  
shown in figure 7, continue on to figure 8.  
•
If the front of your tractor DOEs NOT have front  
mounting holes, go to figure 10.  
FRONT MOUNTING HOLES  
8
•
Remove two self threading bolts (if present) from  
front cross-member of tractor. Assemble bolts through  
lower slots in hitch bracket, then reinstall them back  
into front crossmember. (Make sure notches at top of  
hitch bracket and crossmember are aligned.)  
SELF THREADING BOLT  
FRONT  
•
•
From behind tractor's front crossmember, insert two  
3/8" x 1" hex bolts (3) through holes in crossmember  
and through upper slots in hitch bracket. Secure with  
two 3/8" nylock hex nuts (12).  
3
Go to figure 11 on page 7.  
12  
SELF THREADING BOLT  
19  
FIGURES 9 AND 10 ARE ONLY FOR TRACTORS WITHOUT FRONT MOUNTING HOLES. FOR  
ALL OTHER TRACTORS CONTINUE TO FIGURE 11.  
9
27  
27  
3
19  
x 1  
x 1  
3
19  
12  
12  
x 4  
x 4  
6