Agri Fab Lawn Aerator 45 03431 User Manual

OWnERS  
mAnuAl  
model no.  
45-03431  
DETHATCHER  
FOR SWEEPERS  
CAUTION:  
Read Rules for  
Safe Operation  
and Instructions  
Carefully  
Safety  
Assembly  
Operation  
Maintenance  
Parts  
the fastest way to purchase parts www.speedepart.com  
PRINTED IN U.S.A.  
FORM NO. 42025 (05/27/09)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HARDWARE PACKAGE - Full SiZE  
8
5
6
7
9
13  
14  
15  
12  
16  
17  
11  
10  
18  
NOT SHOWN FULL SIZE  
24  
22  
20  
19  
23  
21  
REF. PART nO. qTY.  
DESCRiPTiOn  
REF. PART nO. qTY.  
DESCRiPTiOn  
5
6
7
8
9
10  
11  
12  
13  
14  
46526  
44292  
43085  
48813  
48811  
3
2
7
2
1
2
2
Hex Bolt, 1/2-13 x 3-1/2"  
Hex Bolt, 5/16-18 x 2-1/2"  
Hex Bolt, 5/16-18 x 1-1/2"  
U-Bolt, 1/4-20  
Hook, Transport  
Washer, 5/16"  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
47810  
43019  
48115  
48812  
44481  
48917  
25054  
46499  
741-0248  
42212  
9
1
3
2
2
2
2
2
4
1
Nylock Nut, 5/16-18  
Jam Nut, Plain 1/2-13  
Jam Nut, Nylock 1/2-13  
Clevis Pin, 5/16" x 1-3/8"  
Vinyl Cap  
43081  
Clamp  
R19171616  
43070  
Washer, 1/2"  
Bracket, U-Bolt Clamp  
Spacer, .8 x 1 x 2.55"  
Flange Bearing  
14 Washer, 3/8"  
2
4
43055  
47189  
Hair Cotter Pin, 3/32"  
Nylock Nut, 1/4-20  
SMARTSweep Hook  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEmBlY (All mODElS)  
ASSEmBlY (nOn-SmARTSWEEP mODElS)  
1. Assemble seven spring tines to the top of the frame  
tube. Use a 5/16" x 1-1/2" hex bolt, two 3/8" flat  
washers and a 5/16" nylock nut for each spring tine.  
Place one 3/8" flat washer on top of the frame tube  
and the second 3/8" flat washer on top of the spring  
tine. See figure 1.  
1. Assemble a conduit clamp onto each end of the  
sweeper height adjustment tube so that the straight  
part of the clamp is on top of the tube. See figure 3.  
2. Remove the hitch brackets and the bolts, if present,  
from the ends of the sweeper's hitch tubes. Slide the  
transport hook onto the L.H. hitch tube as shown in  
figure 3.  
nOTE: On sweepers smaller than 42", use only five spring  
tines.  
3. Reassemble the hitch brackets and bolts to the hitch  
tubes. Refer to your sweeper owner's manual.  
2. Assemble a vinyl cap onto each end of the frame  
tube. See figure 1.  
5/16" x 1-1/2"  
HEX BOLT  
VINYL CAP  
3/8" WASHER  
TRANSPORT  
HOOK  
CONDUIT  
CLAMP  
FiGuRE 3  
5/16" NYLOCK NUT  
FiGuRE 1  
4. Connect the sweeper to the tractor. Set the sweeper  
height adjustment handle to about the middle of it's  
adjustment range.  
5. Place the dethatcher in front of the sweeper housing,  
underneath the hitch tubes.  
6. Connect the dethatcher to the conduit clamp using  
two 5/16" x 1-3/8" clevis pins, 5/16" washers and  
3/32" hair cotter pins. See figure 4.  
3. Assemble a 1/2" washer, the wheel, another 1/2"  
washer and a 1/2" plain jam nut onto the 1/2" x 3-1/2"  
hex bolt. See figure 2.  
4. Insert the bolt through the welded bracket and  
assemble a 1/2" nylock jam nut onto the bolt. Adjust  
nuts so that there is no end play in the wheel and  
then tighten securely against the welded bracket.  
Make sure the wheel still turns freely. See figure 2.  
HEIGHT ADJUSTMENT  
MIDDLE SETTING  
5/16" x 1-3/8"  
CLEVIS PIN  
Use this hole for  
42" & 46" sweepers  
5/16" WASHER  
Use this hole for  
smaller sweepers and  
SMARTSweepers  
1/2" NYLOCK  
JAM NUT  
1/2" JAM NUT  
1/2" WASHER  
1/2" x 3-1/2" HEX BOLT  
3/32" HAIR  
COTTER PIN  
FiGuRE 2  
FiGuRE 4  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
if you have a 30" sweeper, skip steps 7 through 9.  
7. Make sure the sweeper height adjustment handle is  
still set to about the middle of it's adjustment range.  
8. Center the dethatcher with the sweeper.  
ASSEmBlY (SmARTSWEEP mODElS)  
nOTE: The dethatcher attaches to the SMARTSweep  
9. Assemble the keeper brackets (bend to the inside)  
to the sweeper's hitch tube, outside of the conduit  
clamps. Use a u-bolt and two 1/4" nylock nuts  
offset tube. This prevents you from offsetting the sweeper.  
per bracket. Position the keeper brackets against  
the sides of the conduit clamps, approximately  
perpendicular to the ground. Tighten the nylock nuts  
without bending the keeper brackets. See figure 5.  
1. Assemble the four bearings to the two .8 x 1 x 2.55"  
spacers and then slide each through a clamp. See  
figure 7.  
CLAMP  
KEEPER BRACKET  
U-BOLT  
BEARING  
BEARING  
.8 x 1 x 2.55"  
SPACER  
FiGuRE 7  
1/4" NYLOCK NUT  
2. Attach each of the bearing, spacer, and clamp  
assemblies to a mount bracket using a 1/2 x 3-1/2" hex  
bolt and 1/2" nylock jam nut. See figure 8.  
FiGuRE 5  
10. Lift the front of the dethatcher and secure it in  
transport position using the transport hook. See  
figure 6.  
TRANSPORT HOOK  
1/2 x 3-1/2" HEX BOLT  
1/2" NYLOCK  
JAM NUT  
FiGuRE 8  
FiGuRE 6  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Fasten each clamp to the spring mount frame  
assembly using one 5/16 x 1-3/8" clevis pin, 5/16"  
washer, and 3/32" hair cotter pin.  
OPERATiOn  
RAiSinG/lOWERinG THE DETHATCHER  
1. To raise the dethatcher for transport, lift up on the  
front of the dethatcher and secure it with the transport  
or SMARTSweep hook. Lower the dethatcher by  
releasing the hook.  
5/16 x 1-3/8"  
CLEVIS PIN  
5/16" WASHER  
SETTinG THE OPERATinG POSiTiOn  
1. The operating height of the dethatcher is controlled  
by the gauge wheel at the front of the dethatcher  
and is not adjustable. The correct wheel position  
was determined in figure 2 when you assembled the  
wheel.  
3/32" HAIR  
COTTER PIN  
2. Set the sweeper to the desired operating height. (The  
best height is usually with the brushes set about 1/2"  
down into the grass.) Refer to your sweeper owner's  
manual for sweeper.  
FiGuRE 9  
4. Secure the two mount brackets to the inner holes of  
the drawbar offset tube of the sweeper using two 5/16  
x 2-1/2" hex bolts and 5/16" nylock nuts. See figure 10.  
uSinG THE DETHATCHER  
Regular removal of thatch is critical to the maintenance of  
a healthy lawn.Thatch is layer of stems, clippings, runners,  
roots and leaves that have not decayed. Excessive thatch  
prevents air, water and fertilizer from reaching the roots.  
The dethatcher will effectively dislodge excessive thatch  
5/16" x 2-1/2"  
HEX BOLT  
from your lawn.  
1. Start with the tractor in low gear. Vary the forward  
speed to determine the best speed for maximum  
dethatcher performance.  
2. Use a crisscross pattern to achieve the most even  
removal of thatch.  
3. On slopes, always operate in an up and down  
direction only.  
4. Avoid extremely sharp turns.  
5/16" NYLOCK NUT  
5. Avoid towing the dethatcher across sudden steep  
dips in the ground while dethatching. Loss of ground  
contact with the gauge wheel could cause the  
dethatcher to be pulled back underneath the sweeper.  
FiGuRE 10  
5. Slide the SMARTSweep hook onto the sweeper hitch.  
Lift up the front of the dethatcher and slide it into the  
two bottom hooks to secure it in the transport position.  
mAinTEnAnCE  
1. Before each use, check all nuts and bolts for  
tightness.  
2. Clean after each use to help prevent rust.  
3. If rust appears on the spring tines, sand lightly and  
coat with enamel paint.  
SMARTSWEEP HOOK  
STORAGE  
1. Always store in a dry area, and coat exposed metal  
with light oil when not in use.  
FiGuRE 10  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAiR PARTS FOR mODEl 45-03431 DETHATCHER FOR SWEEPERS  
6
5
4
17  
7
12  
15  
18  
10  
20  
23  
24  
2
23  
22  
12  
13  
19  
18  
1
15  
10  
20  
17  
8
16  
21  
14  
11  
13  
11  
3
9
19  
5
REF. PART nO. qTY.  
DESCRiPTiOn  
REF. PART nO. qTY.  
DESCRiPTiOn  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
64650  
46761  
48098  
26624  
46526  
44292  
43085  
48813  
48811  
43081  
R19171616  
43070  
43055  
1
7
1
2
3
2
7
2
1
2
2
Spring Mount Frame Assem.  
Spring Tine  
Gauge Wheel  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
47189  
47810  
43019  
48115  
48812  
44481  
48917  
25054  
46499  
741-0248  
42212  
42025  
4
9
1
3
2
2
2
2
2
4
1
1
Nylock Nut, 1/4-20  
Nylock Nut, 5/16-18  
Jam Nut, Plain 1/2-13  
Jam Nut, Nylock 1/2-13  
Clevis Pin, 5/16" x 1-3/8"  
Vinyl Cap  
Mount Bracket  
Hex Bolt, 1/2-13 x 3-1/2"  
Hex Bolt, 5/16-18 x 2-1/2"  
Hex Bolt, 5/16-18 x 1-1/2"  
U-Bolt, 1/4-20  
Hook, Transport  
Washer, 5/16"  
Clamp  
Bracket, U-Bolt Clamp  
Spacer, .8 x 1 x 2.55"  
Flange Bearing  
SMARTSweep Hook  
Owner's Manual  
Washer, 1/2"  
14 Washer, 3/8"  
Hair Cotter Pin, 3/32"  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
the fastest way to purchase parts www.speedepart.com  
REPAiR PARTS  
Agri-Fab, Inc.  
303 West Raymond  
Sullivan, IL. 61951  
217-728-8388  
This document (or manual) is protected under the U.S. Copyright Laws and the copyright laws of foreign countries,  
pursuant to the Universal Copyright Convention and the Berne convention. No part of this document may be reproduced  
or transmitted in any form or by any means, electronic or mechanical, including photocopying or recording, or by any  
information storage or retrieval system, without the express written permission of Agri-Fab, Inc. Unauthorized uses and/or  
reproductions of this manual will subject such unauthorized user to civil and criminal penalties as provided by the United  
States Copyright Laws.  
© 2003 Agri-Fab, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Alamo Lawn Mower 00756179P User Manual
Bolens Lawn Mower 5264D User Manual
Cub Cadet Lawn Mower 11A 702A101 User Manual
Cub Cadet Lawn Mower SLT X1050 SLTX1054 User Manual
Dixon Lawn Mower ZTR Mowers User Manual
Rover Lawn Mower 405606x108A User Manual
Scag Power Equipment Lawn Mower SFW36 16BV User Manual
Snapper Lawn Aerator 4084 page
Snapper Lawn Mower BH600 User Manual
Snapper Lawn Mower SPXV2270HW User Manual