Zero Turn Mowers
®
ZT60i & ZT72i (S/N 748110+)
Accu-Z
33758
357-552M
Operator’s Manual
Read the Operator’s Manual entirely. When you
see this symbol, the subsequent instructions and
warnings are serious - follow without exception.
Your life and the lives of others depend on it!
!
Cover photo may show optional equipment
not supplied with standard unit.
2/06/14
© Copyright 2014 Printed
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
Important Safety Information
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Look For The Safety Alert Symbol
Safety at All Times
Thoroughly read and understand
the instructions given in this
manual before operation. Refer to
the “Safety Label” section, read all
instructions noted on them.
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and
extra safety precaution must be taken. When you
see this symbol, be alert and carefully read the
message that follows it. In addition to design and
configuration of equipment, hazard control, and
accident prevention are dependent upon the
awareness, concern, prudence, and proper training
of personnel involved in the operation, transport,
maintenance, and storage of equipment.
Do not allow anyone to operate
this equipment who has not fully
read and comprehended this
manual and who has not been
properly trained in the safe
operation of the equipment.
!
ꢀ Operator should be familiar with all
!
Be Aware of
Signal Words
WARNING
functions of the mower.
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury, and
includes hazards that are exposed
when guards are removed. It may also
be used to alert against unsafe
practices.
ꢀ The operator must not use drugs
or alcohol as they can change the
alertness or coordination of that
person while operating equipment.
The operator should, if taking
A Signal word designates a degree or
level of hazard seriousness. The
signal words are:
over-the-counter drugs, seek
medical advice on whether he/she
can safely operate the equipment.
!
DANGER
Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury. This
signal word is limited to the most
extreme situations, typically for
machine components that, for
functional purposes, cannot be
guarded.
!
CAUTION
ꢀ Operate mower from the driver’s
Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
seat only.
ꢀ Make sure all guards and shields
are in place and secured before
operating the mower.
ꢀ Do not leave mower unattended
with engine running.
ꢀ Dismounting from a moving
mower could cause serious injury
or death.
ꢀ Do not allow anyone to stand
between mower and equipment
while backing up to hitch mower to
the equipment.
For Your Protection
ꢀ Thoroughly read and understand
the “Safety Label” section, read all
instructions noted on them.
Shutdown and Storage
ꢀ Put mower in park, turn off engine,
and remove key.
ꢀ Store mower in a area where
ꢀ Keep hands, feet, and clothing
children normally do not play.
away from power-driven parts.
ꢀ Wear snug fitting clothing to avoid
entanglement with moving parts.
ꢀ Watch out for wires, rocks trees,
etc., when using the mower. Make
sure all persons are clear of
working area.
OFF
ꢀ Do not carry passengers on the
mower at any time.
ꢀ Turning mower too tight may
cause hitched machinery to ride
up on the wheels. This could result
in injury or equipment damage.
Parts Manual QR Locator
Dealer QR Locator
The QR (Quick Reference) code on the
front cover and to the left will take you to
the Parts Manual for this equipment.
Download the appropriate App on your
smart phone, open the App, point your
phone on the QR code, and take a picture.
The QR code on the left will
link you to available dealers
for Land Pride products.
Refer to Parts Manual
QR Locator on this page for
detailed instructions.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
ꢀ Repairs or maintenance requiring engine
Practice Safe Maintenance
power should be performed by trained
ꢀ Understand safe and correct maintenance
procedures before doing work. Use proper
tools and equipment, refer to Operator’s
Manual for additional information.
personnel only.
ꢀ Allow mower to cool completely before
performing maintenance.
ꢀ Disconnect battery ground cable (-) before
servicing or adjusting electrical systems or
welding on the mower.
ꢀ Work in a clean dry area.
ꢀ Never run mower in an enclosed area. Mower
engine exhaust emits carbon monoxide and
other poisonous gases.
ꢀ Observe safe fuel handling precautions. Fuel is
flammable and vapors are very explosive.
ꢀ Keep hands, feet, body extremities, and
clothing away from all moving parts such as
pulleys, belts, cutting blades, engine, and
wheels. Don’t wear loose fitting clothing while
operating or servicing mower.
ꢀ Put mower in neutral, set park brake,
disengage blades, turn off engine, remove
switch key and wait for all moving components
to stop before performing maintenance on the
mower.
ꢀ Do not grease or oil mower while in operation.
ꢀ Inspect all parts. Make sure parts are in good
condition and installed properly.
ꢀ Remove buildup of grease, oil, or debris.
ꢀ Replace all guards and floor pan before putting
mower back into service.
ꢀ Remove all tools and unused parts from
mower before operation.
Use Seat Belt and ROPS
Avoid High
Pressure Fluids Hazard
Keep Riders Off Mowers
ꢀ Operate only mowers equipped
with Roll-Over Protective
ꢀ Riders obstruct the operator’s
view, they could be struck by
foreign objects or thrown from the
machine.
ꢀ Never allow children under 16
years of age to operate
equipment.
ꢀ Escaping fluid under pressure can
penetrate the skin causing
serious injury.
ꢀ Avoid the hazard by relieving
pressure before disconnecting
hydraulic lines or performing work
on the system.
ꢀ Make sure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.
ꢀ Use a piece of paper or
cardboard, NOT BODY PARTS, to
check for suspected leaks.
Structure (ROPS) and seat belt.
ꢀ Fasten seat belt snugly and
securely to help protect operator
from being thrown, crushed, or
severely injured if a rollover
occurs; and from falling off the
mower and being ran over. Not
using the seat belt & ROPS can
result in serious injury or death.
ꢀ Wearing protective equipment
such as safety shoes, safety
glasses, hard hat, and ear plugs
is highly recommended.
ꢀ LOW STRUCTURES CAN FLIP
MOWER OVER BACKWARDS.
Lower ROPS to drive under low
structures such as tree limbs and
doorways.
ꢀ Wear protective gloves and safety
glasses or goggles when working
with hydraulic systems.
ꢀ DO NOT DELAY. If an accident
occurs, see a doctor familiar with
this type of injury immediately.
Any fluid injected into the skin
or eyes must be
treated within a few
hours or gangrene
may result.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Wear
Tire Safety
Prepare for Emergencies
Protective Equipment
ꢀ Tire changing can be dangerous
and should be preformed by
trained personnel using the
correct tools and equipment.
ꢀ When inflating tires, use a clip-on
chuck and extension hose long
enough to allow you to stand to
one side and NOT in front of or
over the tire assembly. Use a
safety cage if available.
ꢀ Be prepared if a fire starts.
ꢀ Keep a first aid kit and fire
ꢀ Wear protective clothing and
equipment appropriate for the job.
Avoid loose fitting clothing and
clothing with pull strings.
ꢀ Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
extinguisher handy.
ꢀ Keep emergency numbers for
doctor, ambulance, hospital, and
fire department near phone.
ꢀ When removing and installing
wheels, use wheel handling
equipment adequate for the
weight involved.
ꢀ Operating equipment safely
requires the full attention of the
operator. Avoid wearing radio
headphones while operating
machinery.
911
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
specified by Land Pride. When ordering new components
make sure the correct safety labels are included in the
request.
Safety Labels
Your Zero Turn Mower comes equipped with all safety labels in
place. They were designed to help you safely operate your
implement. Read and follow their directions.
4. Refer to this section for proper label placement.
To install new labels:
1. Keep all safety labels clean and legible.
a. Clean the area the label is to be placed.
2. Refer to this section for proper label placement. Replace
all damaged or missing labels. Order new labels from your
nearest Land Pride dealer. To find your nearest dealer,
3. Some new equipment installed during repair requires
safety labels to be affixed to the replaced component as
b. Spray soapy water on the surface where the label is to
be placed.
c. Peel backing from label. Press firmly onto the surface.
d. Squeeze out air bubbles with the edge of a credit card
or with a similar type straight edge.
818-543C
Danger: Guard Missing
(Beneath Seat Platform)
33759
838-303C
Danger: Battery
(Beneath Seat Platform)
33760
838-829C
Caution: Do Not Power Wash
33764
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
33761
838-307C
Warning: Moving Parts
33761
838-310C
Warning: General
838-815C
Warning: Rollover Hazard
33764
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
838-308C
33764
Warning: Rotating Blade Hazard
838-306C
Warning: Do not operator without deflector
33764
838-833C
Warning: Fuel (Imbedded in Fuel Tank)
33763
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
33762
818-543C
Danger: Guard Missing
3- Places
Beneath Floor platform & Pulley Shields
848-268C
Warning: Safe Operating Instructions
33764
838-444C
Danger: Muffler Hot
33763
(Both Sides of Engine)
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Introduction
Land Pride welcomes you to the growing family of new
product owners.
Terminology
“Right” or “Left” as used in this manual is determined by
facing forward while sitting in the operator seat unless
otherwise stated.
This Zero Turn Mower has been designed with care and
built by skilled workers using quality materials. Proper
assembly, maintenance, and safe operating practices will
help you get years of satisfactory use from this machine.
Definitions
Application
IMPORTANT: A special point of information related
to the following topic. Land Pride’s intention is this
information must be read & noted before continuing.
The Accu-Z ZT60i and ZT72i Zero Turn Mowers from
Land Pride are commercial duty mowers. They are very
maneuverable, extremely comfortable, highly productive,
and come in cutting configurations designed to meet the
needs of even the most discriminating owners and
custom operators. This makes the Zero Turn Mower
Series one of the premier choices of grass maintenance
machines for ranchers, farmers, large estate owners,
cemeteries, municipalities, campuses, and landscape
maintenance contractors.
NOTE: A special point of information that the
operator should be aware of before continuing.
Owner Assistance
The Online Warranty Registration should be completed
by the dealer at the time of purchase. This information is
necessary to provide you with quality customer service.
The Zero Turn Mower Series mowers come equipped
with a choice of either 60" or 72" cutting decks with high
blade tip speeds that range from 18,350 feet per minute
on the 60" deck to 18,800 feet per minute on the 72"
deck. The cutting decks adjust from 1" to 5" cutting height
in 1/4" increments. The 60" deck meet the needs of
customers who need to mow in tighter areas around
obstacles or want to maintain a lower cutting height over
undulating terrain. The more productive 72" cutting deck
will meet the needs of customers with more level and
open areas to cut and just want to get the mowing job
done faster. The Accu-Z is supplied with 27 hp Kawasaki
air cooled engines for proven performance, power, and
reliability.
The parts on your Zero Turn Mower have been specially
designed by Land Pride and should only be replaced with
genuine Land Pride parts. Contact a Land Pride dealer if
customer service or repair parts are required. Your Land
Pride dealer has trained personnel, repair parts, and
equipment needed to service the implement.
For parts and service to your mower engine, contact
your nearest engine dealer or call Customer Service
Hotline provided below.
Owner’s Manual Part No.
Twin-lever hydrostatic steering will enable the Land Pride
Accu-Z Zero Turn Mowers to turn within their overall
length. Couple this outstanding maneuverability with a
maximum 12 mph mowing speed and low center of
gravity and you’ve got mowing capability that’s fast, safe,
comfortable, and easy to transport that will meet your
commercial needs.
Kawasaki - 27 HP. . . . . . 99920-2232
Service Manual Part No.
Kawasaki - 27 HP. . . . . . 99924-2089-01
Service Hotline Phone No.
Kawasaki . . . . . . . . . . . . 1-800-433-5640
Serial Number
Model No. _____________Serial No. _______________
Using This Manual
For quick reference and prompt service, record model
number and serial number in the spaces provided above
and again on warranty page 60. Always provide model
number and serial number when ordering parts and in all
correspondences with your Land Pride dealer. Refer to
Figure 1 on page 9 for location of your serial number
• This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
• The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
• To order a new Operator’s or Parts Manual, contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge, from our website at
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Further Assistance
Your dealer wants you to be satisfied with your new
mower. If for any reason you do not understand any part
of this manual or are not satisfied with the service
received, the following actions are suggested:
1. Discuss the matter with your dealership service
manager making sure that person is aware of any
problems you may have and has had the opportunity
to assist you.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem, and request assistance.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
33761
Serial Number Plate Location
Figure 1
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Assembly & Set-up
Section 1: Assembly & Set-up
Uncrating Instructions
The shipping crate is assembled together with nails. It
can be disassembled by prying or cutting the lumber
apart. Be careful not to scratch, dent, or cut the mower
and seat during disassembly. It is best if two people are
present while disassembling the crate.
1. Remove end and side panels from shipping crate.
IMPORTANT: Do not drive mower off the crate floor,
as this can bend or break components underneath
the mower, especially the transaxles. Lift mower off
the crate floor with a hoist or other suitable lifting
device. Be careful not to damage the paint and seat
while lifting the unit off the crate floor.
2. Gently lift mower from crate floor with a hoist or other
suitable lifting device.
Torque Requirements
determine correct torque values for common bolts. See
“Additional Torque Values” at bottom of chart for
exceptions to standard torque values.
Seat Assembly
Refer to Figure 1-1:
Depending on seat option, the mower may be shipped
with seat attached. If not, the seat (#1) is shipped factory
mounted to the hinged seat platform (#4) and attached to
the shipping crate with lag bolts. It may have already
If not, remove it now.
IMPORTANT: Be careful not to cut seat material
when removing protective packing around the seat.
Cutting seat material will void its warranty.
1. Spread control levers (#2) fully apart before
attaching seat platform to mower frame.
2. Insert flange bushing (#7) into holes “A” as shown.
3. Attach platform (#4) with 3/8"-16 shoulder bolt (#5)
and hex flange lock nut (#6) as shown. Tighten lock
nuts to the correct torque.
4. Connect mower switch wires to the seat switch
located under the seat.
5. Zip tie wire for seat switch to seat pan.
6. Hinge seat platform down. The platform will catch
automatically under the spring loaded latch (#3).
7. Being careful not to cut seat material, remove
protective packing around seat.
33766
Control Lever & Seat Assembly (Standard Seat Shown)
Figure 1-1
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Assembly & Set-up
Discharge Chute Assembly
Refer to Figure 1-2:
The Zero Turn Mower is shipped with carriage bolts (#2)
and hex flange locknuts (#3) attached to the deck in the
location shown. Remove carriage bolts from deck and
attach discharge chute to the deck as follows:
1. Attach discharge chute (#1) to the deck by inserting
3/8"-16 x 1" GR5 carriage bolts (#2) up through deck
bottom as shown.
2. Secure with hex flange locknuts (#3). Tighten lock
nuts to correct torque.
33765
Discharge Chute Assembly
Figure 1-2
Seat Belt Assembly
Seat Belt Retractor (#6) Must Be Mounted This
Side Of Mounting Hole “C” To Keep Retractor
From Interfering With Right Side Fuel Tank.
Refer to Refer to Figure 1-3:
The seat belt is factory assembled when seat is shipped
attached to the mower. Seats lag screwed to the crate
will need the seat belt assembled to the seat.
1. Insert seat belt clip (#4) with push button “A” into clip
sleeve (#5).
2. Make sure push button “A” is facing out as shown.
Insert 7/16" bolt (#1A) through flat washer (#3), seat
belt clip & sleeve (#4 & #5), mounting hole “B” and
flat washer (#3). Secure bolt with nylock nut (#2).
Rotate seat belt up to the approximate angle shown
and tighten nylock nut to 36 ft-lbs. of torque.
3. Orient seat belt retractor (#6) with spring retractor
facing out as shown. Insert 7/16" bolt (#1B) through
flat washer (#3), mounting hole “C”, seat belt
retractor (#6) and flat washer (#3). Secure bolt with
nylock nut (#2). Rotate seat belt retractor to the
approximate angle shown and tighten nylock nut to
36 ft-lbs. of torque.
Spring Retractor
30213
Seat Belt Assembly (Deluxe Seat Shown)
Suspension Seat Includes Seat Belt Mounting holes (B)
Figure 1-3
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Assembly & Set-up
Folding ROPS Installation
In most instances your ROPS (Roll Over Protection
System) will come factory installed with ROPS folded
down at the hinge. Refer to “Unfolding The ROPS”
instructions below if mower is shipped with ROPS
attached. If mower is shipped with ROPS unattached,
!
DANGER
Low structures can make contact with the ROPS and flip the
mower over backwards. Fold ROPS down when driving under
low structures such as tree limbs and doorways.
!
CAUTION
Keep hands and other body extremities away from hinged
pinch points while folding and unfolding ROPS.
Unfolding The ROPS
Refer to Figure 1-4:
ROPS locking knobs (#1) are included in an attached
parts bag.
33824
Folding ROPS Bar Assembly
Figure 1-4
1. Remove hitch pins (#2).
2. Rotate upper ROPS frame up to position shown.
3. Reinsert hitch pins (#2) and secure with attached
hairpins.
4. Install locking knobs (#1) and hand tighten.
Folding ROPS Assembly
Refer to Figure 1-5:
1. Attach lower right-hand ROPS tube (#6) to mounting
bracket “A”. Make sure hinge at the top faces back.
2. Insert two 1/2"-13 x 3" GR5 carriage bolts (#11)
through mounting bracket “A” and ROPS tube (#6).
Secure with 1/2" hex flange lock nuts (#10). Draw
lock nuts up snug, do not tighten.
3. Attach lower left-hand ROPS tube (#5) to mounting
bracket “B”. Make sure hinge at the top faces back.
4. Insert two 1/2"-13 x 3" GR5 carriage bolts (#11)
through mounting bracket “B” and ROPS tube (#5).
Secure with 1/2" hex flange lock nuts (#10). Draw
lock nuts up snug, do not tighten.
5. Attach upper ROPS tube (#4) to lower left ROPS
tube (#5) with 1/2"-13 x 3 1/4" GR5 cap screw (#8)
and hex lock nut (#9). Do not tighten.
6. Attach upper ROPS tube (#4) and ROPS stop (#3) to
lower right ROPS tube (#6) with 1/2" x 3 3/4" GR5
cap screws (#7) and hex lock nut (#9). Do not tighten.
7. Tighten hex flange lock nuts (#10) to 76 ft-lbs. Draw
hex lock nuts (#9) up snug. Do not tighten.
8. Rotate ROPS loop end (#4) up and insert locking
pins (#2). Secure locking pins with hair pin clips
attached to locking pins.
30137
Folding ROPS Bar Assembly
Figure 1-5
9. Install locking knobs (#1) and hand tighten.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Assembly & Set-up
Electrical Cable Connection
Refer to Figure 1-6:
Red Battery
Cable (+)
!
WARNING
Positive Post
Negative Post
Incorrect battery cable connections can damage the mower’s
electrical system and cause battery cables to spark. Sparks
around a battery can result in a battery gas explosion and
personal injury.
Black Battery
Cable (-)
• Always disconnect negative (black) cable from battery
before disconnecting positive (red) cable.
• Always reconnect positive (red) cable to the battery’s
positive (+) post before reconnecting negative (black) cable
to the battery’s negative (-) post.
!
WARNING
Keep battery terminals from touching any metal mower parts
when removing or installing battery. Do not allow metal tools
to short between battery terminals and metal mower parts.
Shorts caused by battery terminals or metal tools touching
metal mower components can cause sparks. Sparks can cause
a battery gas explosion which can result in personal injury.
IMPORTANT: The black negative battery cable is
disconnected before leaving the factory and is to be
disconnected after initial dealer set-up to prevent
battery discharge while sitting on the dealer lot.
33760
Connecting Black Cable To Negative Battery Post
Figure 1-6
Attach black battery cable (#3) to the negative post with
1/4"-20 x 3/4" GR5 serrated screw (#1) and hex whiz
nut (#2). Tighten whiz nut to the correct torque.
Engine Preparations
1. Check engine oil level at the dipstick. Add oil if below
full mark. Do not overfill. Refer to Engine Operator’s
Manual for oil recommendation and to “Engine Oil &
NOTE: Mowers are shipped from the factory
without fuel in the fuel tanks.
stabilizer to the fuel tank.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Operating Procedures
Section 2: Operating Procedures
Mower Features
Refer to Figure 2-1:
Your Zero Turn Mower is designed with innovative and
state-of-the-art features. Knowing the location and how
these features work will make handling your mower more
comfortable. Below is a list of major features to be
reviewed in this section. Not all features listed will be
reviewed.
11
12
13
10
9
4
5
6
8
7
3
2
1
14
13
21
23
22
24
20
15
19
16
14
31
30
29
28
27
3
17
4
7
6
26
10
5
13
18
25
33768
1. Rear Bumper & Engine Guard
2. Battery
3. Fuel Tank
4. Hydraulic Oil Expansion Tank Cap
5. Drive Wheels
6. Tethered Fuel Cap
7. Fuel Vent Valve
8. Park Brake Lever
9. Cup Holders
10. Control Levers
12. 60" or 72" Mower Deck
13. Anti-Scalp Wheels
14. Caster Wheels
15. Floor Platform (Guard)
16. Adjustable Deck Lift Pedal
17. Deck Height Gauge Bar
18. Right Deck spindle Cover (Guard)
19. Deck Height Indicator
20. Operator Seat
23. Seat Release Latch (Behind Seat)
24. Operator Pressure Switch
(Located under seat)
25. Discharge Chute (Guard)
26. Control Panel
(See Figure 2-2 on page 15)
27. Oil Fill / Dip Stick
28. Oil Filter
29. Gas Engine
30. Engine Air filter
31. Engine Exhaust Muffler
21. Seat Platform (Guard)
22. Left/Right Fuel Tank Select Switch
11. Left Deck spindle Cover (Guard)
ZST Mower Features (ZT60i Shown)
Figure 2-1
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Operating Procedures
pulling back on the control levers. Reduce engine rpm
only when mower is not traveling and just before
engaging the cutting blades.
Operating Checklist
Hazard control and accident prevention are dependent
upon awareness, concern, prudence and proper training
involved in operation, transport, maintenance, and
storage of the riding mower. Therefore, it is absolutely
essential that no one operates the mower without first
having read, fully understood, and become totally
familiar with the Operator’s Manual. Make sure the
operator has paid particular attention to:
IMPORTANT: Always operate throttle at full engine
rpm while traveling and cutting grass. Operating
engine at a slow rpm may overheat engine and
transaxles.
Blade Engagement Clutch
Engine Light
Ignition Switch
Hour Meter
The following Operating Checklist should be performed
before operating your mower:
Throttle
Operating Checklist
ꢀ Check
Reference
Choke
33178
Control Panel
Figure 2-2
Choke
A cable is linked from the choke control knob to the
engine for choking the engine during starting. Pull up on
knob to turn choke (ON). Push down on knob once
engine is running to shut choke (OFF).
Check mower safety start interlock system daily
prior to operation.
IMPORTANT: DO NOT operate mower with choke
on.
Make sure there are no hydraulic leaks on the unit. Page 2
Refer to “Avoid High Pressure Fluids Hazard”.
Blade Engagement Switch
The blade engagement switch engages the deck blades.
Pull switch up (ON) to engage blades and push switch
down (OFF) to disengage blades.
Control Panel
IMPORTANT: With mower stopped and engine at
half throttle, engage cutting blades. Increase throttle
to full engine speed and then operate control levers
to move mower. Clutch, belts and/or deck may be
damaged if blades are engaged at full engine speed.
Refer to Figure 2-2:
!
WARNING
Do not operate mower while smoking.
Ignition Switch
Hour Meter
A three position ignition switch: off, run, and start is
provided. With key inserted, rotate it clockwise to START
position; release key when engine starts and switch will
automatically return to RUN position. Turn key
The hour meter registers 1/10 hour increments up to
9,999.9 total hours. The meter is connected to the ignition
switch and records accumulative time only while the
engine is running. Remove plastic film covering over hour
meter before placing mower into service.
counterclockwise to OFF position to stop engine.
Throttle
Engine Light
A cable is linked from engine to throttle for controlling
engine speed. Move throttle lever toward fast position to
increase engine rpm and toward slow position to
decrease rpm. Always travel and cut grass with throttle
set at full engine rpm speed. Decrease travel speed by
The engine light when lit indicate low oil pressure. This
light will come on when starting engine and should go off
soon after engine is started. Shut engine off immediately
if light comes on during normal operation and investigate
cause before putting mower back into service.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Operating Procedures
Park Brake
33758
Refer to Figure 2-3 & Figure 2-4:
The park brake lever is linked to the wheel motors. The
rear wheels are kept from turning when park brake lever
is pulled back or to the (ON) position. Push lever forward
to (OFF) position to release park brakes.
Park Brake (ON)
Mower engine will stop running if park brake lever is set
to (ON) before spreading both control levers (OUT) or if
one or both control levers are moved (IN) before moving
park brake lever to (OFF).
Control Levers
Refer to Figure 2-3 & Figure 2-4:
Both Control Levers Must Be Spread Fully (OUT)
Before Park Brake Is Engaged (ON).
The control levers are used to steer, accelerate,
decelerate, stop, and change direction of travel.
Always move both control levers to neutral position and
then spread them fully (OUT) before setting park brake
lever to the (ON) position. Set park break to the (ON)
position. Always leave park brake and control levers in
this position until ready to start traveling. Move park
brake to (OFF) before pulling control levers (IN). Start
moving by moving control levers either forward or
rearward from neutral position.
Control Levers Fully OUT (in Park Position)
Figure 2-3
33769
Control Levers (IN)
Neutral Operating Position
description of operating the control levers.
Accessing Area Beneath Seat
Platform
Park Brake (OFF)
Refer to Figure 2-5:
The compartment below the seat platform (#2) is where
the control lever linkages, hydrostatic drives, belts, and
fuses are located. The seat is secured over this
compartment with a spring loaded seat latch (#1).
Neutral Slot
NOTE: A carriage bolt may be inserted through
square hole in latch (#1) and secured with a nut.
Torque nut tight to prevent people from easily lifting
the seat platform while mower is operating.
Control Levers Fully IN (In Neutral Position)
Figure 2-4
2
!
WARNING
The seat pan should always be latched in the down position
before starting mower. Not doing so can cause bodily injury.
1
1. Park unit on a flat level surface. Stop engine and
remove ignition key. Make sure blade engagement
switch is in the down (OFF) position. Spread
control levers fully apart and set park brake.
2. Pull latch arm (#1) to the left & lift seat platform (#2)
up to raise seat for viewing compartment below.
3. Close seat platform by lowering platform down until
latch arm catches on the seat platform. See “Seat
33770
Seat Release Latch
Figure 2-5
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Operating Procedures
Accessing Area Beneath Floor
Platform
Hand Holds
Refer to Figure 5-2:
Deck components located under the floor platform (#2)
can be accessed easily by raising the floor platform up
following the steps below.
!
WARNING
The floor pan must always be in the down position before
starting the mower. Not doing so can cause bodily injury.
1. Park unit on a flat level surface. Stop engine and
remove ignition key. Make sure blade engagement
switch is in the down (OFF) position and control
levers are spread fully apart and set park brake.
o
2. Rotate deck lift pedal (#1) back 90 as shown.
3. Using hand holds in floor platform, raise floor
platform (#2) up until resting on it front face as
shown.
33814
4. When finished working, lower floor platform down
using hand holds and rotate deck lift pedal (#10)
forward to normal operating position.
Hinge Floor Platform
Figure 2-6
Moving Mower with Stalled Engine
Refer to Figure 2-7:
Each hydro-drive is equipped with a bypass valve for the
purpose of moving the mower when engine is inoperable.
Both bypass valves are located under the hydro-drive
cooling fan facing towards the center of the mower in the
location shown.
1. Rotate bypass valve slot counterclockwise to vertical
(Bypass) position to allow drive wheel to rotate freely.
3. Position both control levers in neutral with handles
fully apart.
4. Release park brake lever.
5. Manually move mower by hand or with a winch.
IMPORTANT: Do not tow mower. Move it by hand or
use a winch and load it onto a trailer. Make certain
mower is properly secured to the trailer and its park
brake is locked.
PB
IMPORTANT: Following repairs, always make
certain both bypass valves are rotated horizontal
(run position) before operating mower.
Bypass Valve
33771
Bypass Valve (Operating or Run Position Shown)
Figure 2-7
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Operating Procedures
.
33772
Transport Height
Refer to Figure 2-8:
!
CAUTION
Disengage mower blades before changing deck height! Deck
stop pin could get into rotating parts if dropped.
1. Disengage blades, move control levers fully out, and
set park brake.
2. Push forward on deck lift pedal (#1) with your right
foot to raise deck fully up until transport lock (#2)
catches and holds deck up. Release deck lift pedal.
Cutting Height
Refer to Figure 2-8:
Deck Lift Pedal
Figure 2-8
IMPORTANT: The deck must be level and blades
disengaged before setting deck cutting height. See
instructions for “Deck Cutting Height and
Engine Starting
The safety start interlock system is designed to prevent
runaway or accidental entanglement.
IMPORTANT: The starter motor will engage only if
blade engagement switch is (OFF), control levers
are (OUT) , and park brake is (ON).
IMPORTANT: See deck stop (#3) in Figure 2-8.
To operate deck stop pin, push in center button on
head of pin to remove & insert pin.
The following steps are correct procedures for starting
the engine. If difficulty is encountered, contact your local
Land Pride dealer.
NOTE: Cutting height provided on deck height
indicator (#4) is from 1" to 5" in 1/4" increments.
1. Before starting engine, make sure:
a. Blade engagement switch is (OFF).
b. Both control levers are positioned (OUT).
c. Park brake is (ON).
Height” instructions above.
2. Push center button on head of deck stop pin (#3) and
insert pin into desired cutting height pin hole on
cutting height indicator (#4).
2. Set speed control to approximately 1/2 open throttle.
3. Push forward on deck lift pedal (#2) with your right
foot, pull back on transport lock handle (#1), and
slowly release deck lift pedal to gently lower deck
against deck stop pin (#3).
IMPORTANT: Use choke when engine is cold or if
warm and engine fails to start after 5 seconds of
cranking. Avoid engine flooding by pushing choke
control knob to (OFF) as soon as possible.
Clearing Obstacles
IMPORTANT: The engine starter should not be
operated for periods longer then 30 seconds at a
time. An interval of at least two minutes should be
allowed between such cranking periods to protect
the starter from overheating and burn-out.
IMPORTANT: It is best to mow around obstructions;
not over them. Beware, the front of the deck can
clear an obstacle and still make contact by high
centering on the obstacle. Mowing over obstacles
that make contact with the deck can bend/break
mower deck, mower blades, and blade spindles.
3. Insert key into ignition switch and rotate clockwise to
engage starter motor. Release key when engine
starts.
1. If it is necessary to drive over an obstruction, stop
mower, turn off blades, and raise deck fully up to
transport position.
4. Perform test to make sure safety start interlock
2. Move forward slowly to make certain deck clears the
obstruction.
3. Lower deck to cutting height after mower has passed
over obstruction, engage blades, and continue
mowing.
5. As soon as engine begins to run, check to make
certain oil warning light is off. If not, stop engine
immediately, and check for the cause. Refer to
6. Allow engine to idle a few minutes to warm up before
operating the mower.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Operating Procedures
2. Replace blade engagement switch if blades did not
Engine Shut-Down Sequence
run and no other cause such as damaged wiring can
be determined.
It is always best to go through proper shut-down
sequence before turning ignition switch key off. Not
following this sequence in the correct order will cause the
engine to stop running immediately.
Seat Switch
1. With engine running, park brake to (OFF), control
levers (IN), and blade engagement switch (ON),
slowly raise off the seat. The engine should stop
within five seconds.
1. Shut blade engagement switch (OFF).
2. Move both control levers to neutral and (OUT).
3. Throttle engine back to a low idle and wait for one
minute to allow accumulated raw fuel to escape
muffler during engine slow down.
2. Replace seat safety switch if switch did not operate
properly and if no other cause can be determined.
Park Brake Switch
4. Move park brake to the (ON) position.
1. Turn blade engagement switch (OFF) and move
control levers (OUT). Park brake must be (OFF).
5. Rotate ignition key counter-clockwise to (OFF) and
remove from ignition switch.
2. Try restarting engine. Starter motor should not turn.
Safety Start Interlock System
3. Replace park brake switch if starter motor did turn
and no other cause can be determined.
!
Control Lever Switches
1. With blade engagement switch (OFF), control levers
fully (OUT), and park brake (ON), restart engine.
WARNING
Do not bypass any safety switch. Bypassing a safety switch
can result in a serious injury or death.
The mower is equipped with a safety start interlock
system consisting of blade engagement switch, seat
switch, park brake switch, and control lever switches.
This system is an important safety feature designed to
prevent runaway or accidental entanglement.
2. With park brake (ON) and blade engagement switch
(OFF), pull right control lever in. The engine should
stop within five seconds.
3. Replace right control lever switch if switch failed to
operate properly and no other cause can be
determined.
IMPORTANT: The starter motor will engage only if
blade engagement switch is (OFF), control levers
are (OUT), , and park brake is (ON).
4. Return control arm to original setting and restart
engine.
5. With park brake (ON) and blade engagement switch
(OFF), pull left control lever in. The engine should
stop within five seconds.
Only after operator is seated and mower has been
started can park brake be moved to (OFF) and
control levers (IN) in that order or the engine will stop
running. The blade engagement switch can be pulled
(ON) only after park brake is moved to (OFF).
6. Replace left control lever switch if switch did not
operate properly and no other cause can be
determined.
Park brake positioned (ON) or (OFF) does not stop
engine when becoming unseated with both control
levers (OUT) and blade engagement switch (OFF).
Driving the Mower
The safety start interlock system should be checked daily
prior to operation and repaired immediately if it
malfunctions. Inspect system as follows:
!
DANGER
Never make sudden stops or sudden reversing of travel
direction, especially when going down a slope. The steering is
designed for sensitive response. Rapid movement of control
levers could result in a reaction that can cause serious injury.
IMPORTANT: The operator must be on the seat
when testing switches. Contact your local Land
Pride dealer if the problem cannot be resolved.
!
DANGER
1. Start mower engine per instructions in the section on
Never make sudden speed changes from reverse to forward.
Always push control levers forward gently to avoid sudden
change in speed. Any sudden forward speed change can cause
the front wheels to raise off the ground resulting in loss of
control, mower damage and/or personal injury.
2. With blade engagement switch (OFF), control levers
spread fully (OUT), and park brake (ON), slowly raise
off the seat. The engine should continue to run.
NOTE: When turning on soft wet turf, keep both
wheels rolling either forward or backward. Pivoting
on a stopped wheel can damage the turf.
Blade Engagement Switch
1. With engine running and operator sitting on the seat,
move park brake to (OFF), pull both control levers
(IN), and then turn blade engagement switch (ON).
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Operating Procedures
Front of Mower Faces This Direction
2
3
1
4
5
6
7
25880
Figure 2-9
To Start and Increase Speed
To Steer
Refer to Figure 2-9 on page 20:
Refer to Figure 2-9:
After starting the engine, release park brake, and engage
control levers by moving handles fully (IN). This makes
the levers ready for steering while traveling. Moving
control levers an equal distance away from neutral will
increase travel speed.
• To Steer Straight While Traveling Forward
(Ref. Frame #3):
Push control levers forward an equal distance.
• To Steer Straight While Backing Up (Ref. Frame #4):
Pull control levers rearward an equal distance.
• Start forward travel by gently pushing on the control
levers. The further forward the control levers are
pushed the faster the travel speed.
• To Turn Left While Traveling Forward (Ref. Frame #5):
Move right control lever farther forward from neutral
than the left control lever.
• Start backing up by gently pulling on the control levers.
The further back the control levers are pulled the faster
the travel speed.
• To Turn Right While Traveling Forward:
Move left control lever farther forward from neutral
than the right control lever.
To Decrease Speed and Stop
Refer to Figure 2-9:
• To Turn Right While Backing Up (Ref. Frame #6):
Move left control lever farther back from neutral
than the right control lever.
!
WARNING
In the event of a system shutdown while mowing, move control
levers to neutral, and spread them fully apart. Also, engage
the park brake lever to aid in slowing and stopping the mower.
• To Turn Left While Backing Up:
Move right control lever farther back from neutral
than left control lever.
• When moving forward, pull back gently on control
• To Make A Pivot Turn (Ref. Frame #7):
levers to decrease speed until neutral is reached.
Move one control lever forward and the other
control lever back of neutral, this will allow the drive
wheels to counter-rotate.
• When backing up, push forward gently on control
levers to decrease speed until neutral is reached.
• Move control levers to neutral to stop. (Ref. Frame #2)
• Spread both control levers fully apart and engage park
brake when stopped for awhile. (Ref. Frame #1)
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Operating Procedures
Safe Operating Instructions
!
The safe operation of any machinery is a big concern to
all consumers. Your Zero Turn Mower has been designed
with many built-in safety features. However, no one
should operate this mower before carefully reading this
Operator’s Manual and all instructions noted on the
safety decals.
WARNING
Mower deck and floor pan can be slippery when wet. Always
step on anti-slip pads when possible. Never hurry. Always
make sure your footing and hand hold is secure when climbing
onto the mower to be seated.
!
WARNING
!
The tailpipe and muffler are very hot and can ignite dry
grasses, brush and other flammable materials. Always keep
area around muffler and tailpipe clear of debris. Allow muffler
and tail pipe to cool completely before removing any debris to
prevent sever burns to the body. Make sure all debris around
the muffler have been removed before parking mower inside a
building or garage.
DANGER
Prior to operating the mower, the operator should be
thoroughly familiar with proper use and operation of the
machine, should read the manual completely and thoroughly,
and should have attempted slow moving maneuvers to become
familiar with the operation of the machine before attempting
normal speed operation. An inexperienced operator should
not mow on slopes or on uneven terrain.
!
WARNING
!
Always wear hearing protection, safety glasses, clothing that
does not hang loosely, and shoes or boots when operating this
machine. All shirts should be buttoned up the front and tucked
in the trousers, long sleeve shirts should be buttoned at the
cuffs. Some conditions may warrant extra safety gear be worn
such as dust masks for dust inhalation and safety helmets.
DANGER
All guards including floor pan and seat platform must be
installed and in good condition at all times during operation.
!
DANGER
Always use seat belt with the Roll Over Protection System
(ROPS). The ROPS can offer protection to the operator in a
rollover situation only if that person is contained within the
ROPS perimeter. Not using the seat belt in a rollover situation
can throw the operator from the mower causing serious injury
or death.
!
CAUTION
Always check area to be mowed for rocks and other debris
before mowing.
ꢀ Be familiar with all functions of this mower.
ꢀ Do not operate mower with damaged parts. Repair all
damaged and defective parts before putting mower
back in to service.
!
DANGER
Never place hands or feet under the deck or attempt to make
any adjustments to the mower deck while the engine is running
or when blades are engaged. Mower blades rotating at a high
speed cannot be seen and are located very close to the deck
housing. Fingers and toes can be cut off instantly.
ꢀ Keep all bystanders away from this mower during
operation.
ꢀ Do not allow anyone to operate this mower who has
not fully read and comprehended this manual and has
not been properly trained in its safe operation.
!
ꢀ Do not allow anyone under 16 years of age to operate
DANGER
Do not mow with people present in the mowing area.
Projectiles can suddenly, without warning, discharge from
under the mower deck causing serious injury or death.
this mower.
ꢀ Do not carry riders on the mower or in a cart towed
behind the mower. Carrying riders can result in serious
injury and/or death to rider and operator.
ꢀ Do not operate mower while drinking or under the
!
DANGER
influence of alcohol or drugs.
Never direct discharge of material from mower deck towards
people, animals or buildings. Keep discharge chute in its
lowest position and never remove discharge chute unless a
complete grass collection system is in place. Projectiles can
suddenly, without warning, discharge from under the mower
deck causing serious injury or death.
ꢀ Always operate mower at a safe travel speed that will
maintain control. Allow time to react to obstacles in the
mower’s path. Reduce speed on rough, wet, slick or
unstable ground. Take care when driving around trees
so as not to scrape them. Do not make sudden
uncontrolled changes with control levers. Change
speed and direction with steady controlled movements
of the control levers. Never drive recklessly.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Operating Procedures
ꢀ Drive Zero Turn Mowers up and down slopes, not
across slopes. Use a walk behind mower when
mowing across slopes.
ꢀ Battery fumes are explosive. A spark will ignite battery
fumes. Wear a face shield when charging or jumping a
battery. Follow all battery safety rules in this manual.
ꢀ Do not operate Zero Turn Mowers on slopes greater
than 15 degrees. They are heavy and can crush a
person if they rollover sideways or flip over backwards.
ꢀ Avoid battery acid spills. Do not get battery acid on
eyes, face, or other body parts. Flush eyes and other
body parts immediately with water for at least 15
minutes if battery acid has gotten on them.
ꢀ Stay two or more mower widths away from drop-offs
such as ditches and retaining walls. Use a walk behind
mower or string trimmer close to drop-offs.
ꢀ Never modify engine RPM or any parts on the mower
without authorization. Unauthorized modifications will
void warranty to all parts directly and indirectly affected
by the modification.
ꢀ Do not drive too close to water. The surface near water
is often soft, wet and unstable. The grass can be wet
and slippery. Use a walk behind mower or string
trimmer when close to water.
ꢀ Do not pull a trailer or implement with mower. Loss of
control and damage to mower may result.
ꢀ Be aware of and avoid overhead hazards such as guy
wires, tree limbs and brush that have the potential of
stopping the mower or hitting and/or poking one while
riding the mower. Mark any potential hazards and be
alert to their presence.
ꢀ Do not push other equipment with front of mower.
ꢀ Do not tow mower with its wheels on the ground.
Always tow mower loaded on a trailer. Make certain
the mower is properly secured to the trailer and its
park brake is locked.
ꢀ Thoroughly inspect area to be mowed for unforeseen
hazards in the grass such as rocks and other debris.
Mark potential hazards that cannot be removed and be
alert to their presence.
ꢀ Do not smoke or use electrical devices including cell
phones while refueling.
ꢀ When refueling use a UL listed container that has a
screen or filter. Set container on the ground before
fueling to eliminate static discharge. Do not use
Methanol fuel.
ꢀ Always operate mower with belt guards installed. Do
not operate mower with floor pan removed exposing
pulleys and belts.
ꢀ Always maintain proper tire inflation. See “Tire
Inflation Chart” on page 59.
ꢀ Always wear long pants, ear plugs, safety glasses and
safety shoes for personal protection. Some conditions
may warrant extra safety gear be worn such as dust
masks and safety helmets.
ꢀ Always disconnect negative battery terminal before
making adjustments to the mower’s electrical system
or welding on the mower.
ꢀ Keep hands, feet, long hair, clothing, and jewelry away
from moving parts and obvious pinch points to avoid
entanglement. Clothing should be snug-fitting,
buttoned and tucked in the trousers.
ꢀ Support this mower securely before working beneath.
Chock wheels to prevent mower from rolling.
ꢀ Always check wheel lug nut torque values two hours
after initial operation and two hours after each tire
repair and/or replacement. Routinely check lug nut
torque valves every 50 hours of operation. See also
ꢀ Do not leave mower unattended with engine running..
ꢀ Use extreme caution when driving through dry grass,
brush and other fire hazard materials. Never stop or
park over combustible materials. Keep grass and
brush from collecting on and around engine and
muffler parts.
Good Operating Practices
ꢀ Use extreme caution when cresting hills or when
visibility is limited. Proceed slowly until you are sure
conditions immediately ahead are safe.
Engage blades with engine running at medium
speed. Pull up on blade engagement switch to start
blades turning. Once blades are fully engaged and
turning, increase engine speed to maximum engine
operating speed.
ꢀ Do not operate mower at night. With poor visibility,
night operation can lead to a serious accident.
ꢀ Do not operate mower on streets, highways, public
roads, or where it may be a hazard to faster moving
traffic.
NOTE: Engaging blades when under heavy load
(i.e. tall grass) or at high engine rpm can cause
premature belt wear and/or belt damage.
ꢀ Always park on level ground with control levers fully
apart in neutral, park brake set, engine shut off, and
switch key removed before leaving mower unattended.
Cut grass with blades operating at full speed. Your
Zero Turn Mower operates at peak mowing performance
and gives the best cut when the throttle is set at full rpm.
This gives maximum power to the drive wheels and
cutting blades when needed. Use control levers to
control ground speed rather than engine rpm.
ꢀ Do not touch engine, engine exhaust pipe and/or
muffler while they are hot.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Operating Procedures
The mower’s control levers are very responsive. For
smooth operation, move levers slowly, avoid sudden
movement. Skill and ease of operation come with
practice and experience. Inexperienced operators may
have a tendency to over-steer and lose control.
Slow-moving practice maneuvers are recommended to
become familiar with these characteristics before
attempting normal speed operation.
With the engine at half throttle, release the parking brake
by pushing the lever forward and down all the way. Then
reach forward and bring both steering levers equally
together in the neutral position just in front of you. It’s now
time to test your steering skills. Gently push both steering
levers equally forward. The farther forward you push the
levers the faster you will go. Pull back equally and you will
slow down coming to a stop when you reach the neutral
position. Now slowly pull the levers back toward your
body past neutral position. The mower will reverse
direction and increase in speed as you pull further back.
If you push one lever forward and pull one lever back the
mower will do a zero turn in the direction of the steering
lever closest to your body. Now take a few moments in a
safe open area to practice maneuvering and steering
your mower with the engine still at half throttle. Gradually
increase your throttle speed until you feel totally
Approach depressions & raised obstacles carefully.
Sharp depressions or raised obstacles (such as gutters
or curbs) should not be directly approached at high
speed in an attempt to jump them as the operator could
be thrown from the mower. Approach at a slow speed
and angle one drive wheel at the obstruction. Continue at
an angle until both wheels clear the obstruction.
Protect turf by keeping both drive wheels rolling
when making turns. When turning on soft wet turf, keep
both drive wheels rolling either forward or backward.
Pivoting on a stopped drive wheel can damage the turf.
confident of your mower steering and handling ability
around obstacles and in tight areas.
It’s now time to cut the grass. Hopefully, you have already
removed any obstacles from the lawn that you do not
want run over. With your mower at half throttle, place your
right foot on the deck lift pedal and release and lower the
deck to your preset cutting height. With your right hand,
pull up on the cutting blade engagement knob and
increase the engine speed to full throttle. You may now
begin mowing. When you are done mowing or just want
to take a break, make sure you do all of the following.
Select a mowing pattern that discharges cut grass
away from uncut grass. Use a pattern utilizing left turns
because cut grass is discharged to the right. Avoid
discharging cut grass onto uncut areas as grass is then
mowed twice. Mowing twice puts an unnecessary load
on the mower and reduces mowing efficiency.
Keep blades sharp. Many problems with incorrect
cutting patterns are due to dull blades or blades which
have been sharpened incorrectly. Information on
sharpening blades is listed in this manual’s maintenance
section. In addition, most communities have individuals
or companies which specialize in sharpening mower
blades. Blade sharpness should be checked daily.
• Park on level ground if possible.
• Disengage cutting blades.
• Throttle back.
• Place steering levers in wide-open neutral position.
• Engage park brake lever.
• Turn engine off and remove switch key.
General Operating Information
After thoroughly familiarizing yourself with the Operator’s
Manual and completing the Operator’s Checklist, you are
almost ready to begin mowing.
• Step carefully off the left side of the operator’s
platform.
• You may want to chock the wheels as an added
measure of safety, if and when you must park on an
incline.
Approach the mower from the front and spread the
steering levers fully apart. Stand just to the outside rear
of the left front anti-scalp wheel and with your right hand
grab the left side steering lever for support. Taking care
not to slip on the mower deck, step up onto the operator’s
platform and comfortably seat yourself. The park brake
lever just to your left and adjacent to the operator’s seat
should be fully raised and in the (ON) position. With both
steering levers still wide apart now reach for the throttle
and choke control to your right side. Position the throttle
control at half throttle and pull the choke to the “up/on”
position. Insert your ignition key and rotate the ignition
key clockwise until you hear the engine begin to start.
Release the ignition key and push the choke to
In the unlikely event that you lose electrical power and
the Zero Turn Mower shuts completely down, you will
lose hydrostatic steering capability. Should the engine
fail for any reason and you need to push or pull the unit a
short distance for loading or servicing, make sure you
open bypass valves on the transaxles.
The Land Pride Zero Turn Mowers are designed to
deliver professional cutting quality, while delivering high
productivity and sustained comfort over extended
periods of operation. With just a little bit of practice you
should become very good at operating your mower. See
the “Features and Benefits” section of this manual for
additional product information and performance
enhancing options.
“down/off” position. Allow the engine to warm up
momentarily. If your mower has just been running and the
engine is already warm, using the choke is probably not
necessary.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Adjustments
Section 3: Adjustments
!
WARNING
Unless specifically required, Do Not have engine running
when servicing or making adjustments to the mower. Place
both control levers in the park position and remove ignition
switch key. Read and observe all “Safety Warnings” and
“Important Notes” in this manual.
Repairs or maintenance requiring engine power should be
performed by trained personnel only. To prevent carbon
monoxide poisoning, be sure proper ventilation is available
when engine must be operated in an enclosed area.
Your Zero Turn Mower was adjusted before it left the
factory and checked for proper operation during
pre-delivery set-up. However, break-in wear and
continued use can cause some adjustments to change.
• Be alert for unusual noises while operating the mower.
They could be signaling a problem.
• Visually inspect for abnormal wear or damage while
servicing and making adjustments to the mower.
Proper servicing and adjustment is the key to the long life
of any implement. With careful inspection and routine
maintenance, you can avoid costly downtime and repair.
33817
Park Brake Adjustment
Figure 3-1
!
WARNING
Refer to Figure 3-1:
Keep your mower clean. Remove heavy trash and clippings
from mower. Keep all moving parts, hydraulic system, engine
cooling system, and exhaust system clean of trash and
clippings. Accumulation of trash and/or clippings can cause
fires, hydraulic overheating and excessive belt wear.
1. Check distance nut (#5) is from end of threaded
mount (#6). If distance is about 1/8", skip to step 4.
2. Back nut (#5) away from engine platform until about
1/8" from end of threaded mount (#6).
Clear away heavy build-up of grease, oil, and dirt.
Especially clean in the areas around oil openings, fuel
openings, and air inlets. Minute dust particles are
abrasive to close-tolerance engine and hydraulic
components.
3. Tighten jam nut (#4) against engine support plate.
4. Loosen nut (#2) 5 or 6 turns.
Some repairs require the assistance of a trained service
mechanic and should not be attempted by unskilled
personnel. Consult your Land Pride service center when
assistance is needed.
a. Tighten nut (#3) one-half turn at a time until
applied pressure at break lever (#1) is
satisfactory.
b. Tighten nut (#2) against lever housing.
Torque Requirements
c. Ensure cable adjustment allows linkage (#7) to
return fully to disengaged position. Not doing so
may cause premature wear and unnecessary
heat in the transaxle.
“Additional Torque Values” at bottom of chart for
exceptions to standard torque values.
d. Move mower to an incline and recheck break lever
to make certain park breaks will hold mower on an
breaks will hold on an incline.
Tire Pressure
Before considering any adjustment, check air pressure in
the tires. Unequal tire pressure will cause mower to drift
to one side and cut grass at unequal heights. Refer to
“Tire Inflation Chart” on page 59.
6. If break lever (#1) applies too hard, continue with
a. Loosen nut (#3) one-half turn at a time until
applied pressure at break lever (#1) is
satisfactory.
Park Brake Adjustment
Over time, the park brake cable can stretch changing the
effectiveness of the park brakes. Adjust park brakes if
they do not hold on an incline or if the park brake lever
applies too easy or too hard.
b. Tighten nut (#2) against lever housing.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Adjustments
c. Ensure cable adjustment allows linkage (#7) to
return fully to disengaged position. Not doing so
may cause premature wear and unnecessary
heat in the transaxle.
d. Move mower to an incline and recheck break lever
to make certain park breaks will hold mower on an
hold on an incline.
Seat Reach Adjustment
The seat should be adjusted forward or rearward to a
comfortable position to operate the deck lift pedal.
33773
1. With operator sitting in the seat, place his or her right
foot on the deck lift pedal.
Deluxe Seat Reach Adjustment
Figure 3-2
2. Press down on the pedal as if to change the cutting
height to determine if the seat is too close to the
pedal, too far away, or at the correct distance.
Pedal Adjustment” below.
4. If seat needs adjusting, pull spring loaded seat latch
(#1) to the left and move seat forward or rearward to
a comfortable setting.
5. Release spring loaded seat latch and recheck your
reach from seat to deck lift pedal to make sure it is
comfortable.
6. If the operator is still uncomfortable with his or her
reach to the deck lift pedal, then adjust the deck lift
pedal as instructed below.
33773
Suspension Seat Weight Adjustment
Refer to Figure 3-3:
Suspension Seat Reach Adjustment
Figure 3-3
The Suspension Set can be adjusted to accommodate
different weights to idividualize the operator’s own
comfort ride while mowing over uneven terrain.
1. Dial knob (#2) under the seat clockwise to
accommodate more weight and counterclockwise to
accommodate less weight.
Deck Lift Pedal Adjustment
Refer to Figure 3-4:
The deck lift pedal has three positions it can be adjusted
to suit operator comfort.
1. Loosen carriage bolt (#5). Do not remove.
2. Unscrew hex flange nut (#4) and remove carriage
bolt (#3) from lift arm (#2).
3. Rotate deck lift pedal to the preferred square hole
and reinsert carriage bolt (#3). Secure carriage bolt
with hex flange nut (#4).
33774
Deck Lift Pedal Reach Adjustment
Figure 3-4
4. Tighten 3/8"-16 x 1 1/4" GR5 carriage bolts (#3 & #5)
to the correct torque.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Adjustments
Steering Adjustments
The lower and upper steering levers may require
readjusting to make operating the mower more
comfortable.
Lower Control Lever
Refer to Figure 3-5:
The hydrostatic drive system is designed with spring
return pump arms (#5) that will return the lower steering
control levers (#2) to neutral when released from reverse
position. If control levers do not return to neutral position
when released from reverse position, adjust length of
pump linkage rods (#1) as follows:
!
WARNING
Make sure mower is turned (OFF) before making adjustments
to pump linkage rods.
1. Push blade engagement switch to (OFF) and turn
ignition switch (OFF).
2. Position control levers in neutral position as shown.
Neutral
Parking Slot
NOTE: Step 3 is not required but may be done if
transaxle fan blades (#4) interfere with loosening
jam nuts (#3).
3. If needed, remove fan mounting hardware and
fan (#4) if jam nuts (#3) are not easily accessible.
4. Loosen jam nuts (#3) at both ends of linkage rod (#1)
by 5 or more full turns (approximately 1/4"). One jam
nut will be right-hand thread and the other will be
left-hand thread.
5. Using the flat area (#1) on the linkage rod, rotate rod
to lengthen or shorten it until lever arm (#2) aligns
with neutral parking slot.
33775
6. Tighten jam nuts (#3) at both ends to lock linkage rod
in place.
Steering Control Linkage
Figure 3-5
8. If transaxle fans were removed, reinstall them and
tighten their hardware to the correct torque.
9. Start mower engine and test control lever alignment
by moving levers forward and backward before
returning them to neutral position. The pump linkage
rods (#1) are properly adjusted if the lower control
levers (#2) are aligned with neutral parking slots in
the mower housing when released.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Adjustments
Upper Control Lever
IMPORTANT: Make sure lower control levers have
been adjusted before adjusting upper control levers.
See page 26 for lower control lever adjustments.
The upper control levers may be adjusted while in neutral
position for height, reach, and forward travel to fit the
operator’s steering comfort zone.
Height Adjustment
Refer to Figure 3-6:
1. Adjust upper control levers (#2) vertically by removing
bolts (#3), and hex flange locknuts (#4) that attach
upper levers to the lower steering arms (#1).
2. Reposition upper control levers in holes A, B & C to a
height that fits the operator’s personal preference.
3. Reassemble bolts and hex flange locknuts in the
same order they were removed without tightening
them.
Reach Adjustment
Refer to Figure 3-6:
The upper control levers (#2) can be adjusted forward or
rearward to make steering more comfortable.
NOTE: Adjust seat reach to operate the deck pedal
comfortably before making “Reach Adjustment” to
the upper control levers. See “Seat Reach
33776
Control Lever Adjustment
Figure 3-6
1. Loosen hex flange locknuts (#4) and pivot upper
control levers (#2) forward or backward to fit
operator’s personal reach preference.
3. You can either adjust the trailing lever forward by the
distance it was trailing or adjust the leading lever
back by the distance it was leading.
2. Verify that the control levers align with each other
when in neutral and tighten hex flange locknuts (#4)
to the correct torque.
a. Loosen hex flange locknuts (#4) on the side to be
adjusted.
Forward Travel Adjustment
Refer to Figure 3-6:
b. Reposition the lever forward or backward by the
distance it was trailing or leading.
“Reach Adjustment” instructions adjust upper control
levers to be equally aligned while in neutral. However,
with this adjustment, the mower may want to steer
slightly to the right or left when pushing the levers equally
forward.
c. Retighten hex flange locknuts (#4) to the correct
torque.
Example:
If the right control lever is one inch ahead of the left
control lever, stop unit and either adjust the right
upper control lever back one inch or adjust the left
upper control lever forward one inch.
Make the following adjustments if you prefer to have
upper control levers equally aligned while in forward
travel position instead of neutral position:
1. While driving forward, make necessary steering
correction required to make the unit go straight and
take careful notice of how the upper control levers
are positioned. (The distance one lever is ahead of
the other to make the mower travel straight.)
2. Stop mower on a level surface, place control levers in
neutral, set park brake (ON), shut power off and
remove switch key.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Adjustments
Belt Tensioning
There are two drive belts on the ZTi mower. The ground
drive belt is the upper belt that powers the mower’s rear
wheels (see Figure 3-7). The deck drive belt is the lower
belt that powers the mower deck blades (see Figure 3-9).
IMPORTANT: Do not over tension drive belts to
compensate for a badly worn belt or pulley.
An over tensioned belt can cause the belt and drive
components to break prematurely resulting in a
safety hazard to the operator and bystanders.
An under tensioned belt can cause the belt to slip
and become damaged.
Ground Drive Belt Tensioning
Refer to Figure 3-7:
The ground drive belt (#5) remains in constant tension by
means of a spring tensioned idler (#1). If belt slips under
normal operating load conditions, retention spring (#4)
by tightening eyebolt (#2). Replace belt when it becomes
excessively worn or damaged. Instructions for replacing
the ground drive belt are provided on page 38.
33777
Ground Drive Belt Adjustment
Figure 3-7
1. Check length of ground drive extension spring (#4) to
verify if belt tension is correct. Installed spring length
should be 7" +/- 1/8" (See Figure 3-8).
2. Adjust belt tension as follows:
a. Loosen hex whiz nut (#3A).
Spring Length = 7" +/- 1/8"
33200
b. Tighten or loosen whiz nut (#3B) until spring
length is 7" as shown in Figure 3-8.
Take-up Spring Length
Figure 3-8
c. When adjustment is complete, hold hex whiz
nut (#3B) still while tightening hex whiz nut (#3A).
Deck Drive Belt Tensioning
Refer to Figure 3-9:
The deck belt (#9) remains in constant tension by means
of the spring tensioned idler (#8). If belt slips under
normal operating load conditions, re-tension spring (#4)
by tightening up eyebolt (#2). Replace deck belt when it
becomes excessively worn or damaged. Instructions for
replacing the deck drive belt are provided on page 37.
Vary spring length by adjusting length of eye bolt (#2).
Additional adjustments to the spring length can be made
by changing which hole in Arm (#1) the spring is
attached. There are two holes for this adjustment.
1. With deck cutting height set at 3", check length of
extension spring (#4) to verify proper belt tension.
Installed spring length should be 7" +/- 1/8" (See
Figure 3-8).
2. Adjust belt tension as follows:
a. Loosen hex whiz nut (#3A).
b. Tighten or loosen whiz nut (#3B) until spring
length is 7" as shown in Figure 3-8.
33778
c. When adjustment is complete, hold hex whiz
nut (#3B) still while tightening hex whiz nut (#3A).
Deck Drive Belt Adjustment
Figure 3-9
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Adjustments
Refer to Figure 3-11 on page 30:
Deck Cutting Height and Leveling
Refer to Figure 3-10:
6. Remove tension on deck lift assist springs (#7) so
that the deck can properly rest on the support blocks
!
WARNING
Make sure blade engagement switch is (OFF), switch key is
(OFF) and removed from ignition switch, control levers are
(OUT), and park brake is (ON) before making adjustments.
b. Back jam nuts (#4) and adjusting nuts (#5)
counterclockwise to the end of the eyebolt to
remove spring tension.
IMPORTANT: See deck stop (#4) in Figure 3-9.
To operate deck stop pin, push in center button on
head of pin to remove & insert pin.
Refer to Figure 3-10:
7. Loosen upper hex whiz nuts (#3A) on both sides
(4-places) of mower deck until deck is completely
resting on support blocks (#7).
When level, the bottom edge of the deck should be 3"
above ground level with deck stop pin (#4) inserted in
Deck Leveling hole (#5) (3.25" hole). If needed, readjust
deck height:
8. Insert stop pin (#4) into 3 1/4" “Deck Level Hole” (#5).
9. Push forward on deck lift pedal (#1) with your right
foot, pull back on transport lock handle (#2) and
slowly release deck lift pedal to gently lower deck
against stop pin (#4).
1. Check tire pressures to make certain they are
properly inflated. See “Tire Inflation Chart” on page
59 for correct tire pressures.
2. Park unit on a flat level surface.
10. Adjust lower 3/8" hex whiz nuts (#3B) up or down on
both sides of mower deck (4-places) until deck is fully
resting on all support blocks, deck lift pedal is fully
against deck stop pin (#4), and eye bolts (#6) are
tight with no slack in support chains above eye bolts.
3. Push forward on deck lift pedal (#1) with your right
foot to raise deck fully up until transport lock (#2)
catches and holds deck up. Deck should stay up after
releasing your right foot.
11. Hold hex whiz nuts (#3B) from turning and tighten
hex whiz nuts (#3A) to the correct torque on both
sides (4-places) of the mower deck.
NOTE: Two 2" x 4" x 5" or longer boards may be
stacked to make one 3" high support block.
4. Place two 3" high blocks (#7) under the deck’s front
edge in-line with the left and right blade spindles.
12. Readjust deck lift assist springs. Refer to “Deck Lift
5. Place two 3" high blocks (#8) under the deck’s back
edge in-line with the left and right blade spindles.
3"
33779
Deck Cutting Height & Leveling (48" Deck Shown)
Figure 3-10
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Adjustments
Deck Lift Assist Springs
Refer to Figure 3-11:
There are two deck lift assist springs (#7). They are
located under the floor platform and will require
adjustment when the linkage to hold the deck at its
cutting height will not stay against deck stop pin (#6) or
when the force to push the deck lift pedal (#2) is too
great.
1. Lower deck to its lowest mowing position to ensure
deck is still tight against stop pin (#6).
3. Back jam nuts (#4) away from adjusting nuts (#5).
• Turn adjusting nuts (#5) clockwise an equal
amount to increase spring tension and to make
lifting the deck easier.
• Turn adjusting nuts (#5) counterclockwise to
decrease springs tension and to increase deck
weight against stop pin (#6).
4. After adjusting nuts (#5) has been properly adjusted
for both springs (#7), tighten jam nuts (#4) against
adjusting nuts (#5).
5. Replace floor platform and return deck lift pedal to
operating position.
Spring tension eyebolts (#3) may need
adjusted for customer preference.
33815
Deck Adjustment (Left Side Shown)
Figure 3-11
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Adjustments
1. Position mower and deck on a flat level surface.
Anti-Scalp Rollers
2. Set deck to the preferred mowing height. (Refer to
Refer to Figure 3-12:
The mower has four anti-scalping rollers. Their purpose
is to minimize scalping of the ground when mowing on
rough uneven terrain. Their height should be adjusted
after setting stop pin to the preferred cutting height.
3. At middle bracket (#2), remove 1/2" hex nylock jam
nut (#6) and remove carriage bolt (#5).
4. Reposition both anti-scalp rollers (#8B & #8C) up or
down in mounting bracket (#2) until rollers are in the
lowest hole possible without rollers touching the
ground. See important note on this page.
IMPORTANT: The anti-scalp rollers will extend
below deck bottom the distance shown below when
mounted in the following holes:
5. Reinstall carriage bolt (#5) through anti-scalp
rollers (#8B & #8C) and secure to mounting
bracket (#2) with flat washer (#7) and hex nylock
nut (#6). Tighten nylock nut to the correct torque.
• Top hole: rollers are even with deck bottom.
• 2nd hole: rollers are 1/2" below deck bottom.
• 3rd hole: rollers are 1" below deck bottom.
• 4th hole: rollers are 1 1/2" below deck bottom.
• Bottom hole: rollers are 2" below deck bottom.
6. At end brackets (#3), remove nylock jam nut (#6) and
remove carriage bolts (#4).
7. Reposition end anti-scalp rollers (#8A) and
spacers (#1) on end brackets (#3) up or down until
rollers are in the lowest possible mounting hole
without rollers touching the ground. See important
note on this page.
For protection of deck and blades, it is best if the anti-
scalp rollers are mounted in the lowest holes
possible without them touching the ground.
For example:
If deck cutting height is set 1 1/2" above ground, the
rollers should be mounted in the 3rd hole down or 1"
below the deck bottom.
8. Reinstall carriage bolt (#4) through anti-scalp
rollers (#8A) and spacer (#1) to end mounting
brackets (#3) with flat washer (#7) and hex nylock
nuts (#6). Tighten nylock nuts to the correct torque
33780
Anti-Scalp Roller Adjustment
Figure 3-12
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Options & Accessories
Section 4: Options & Accessories
Folding Soft Top Canopy
Refer to Figure 4-1:
Keep the sun off with this easily assembled, ROPS
attached canopy. Made with a lightweight aluminum
frame and acrylic coated polyester, you’ll be more
comfortable during those sunny afternoons.
Soft Top Canopy . . . . . . . . . . . . . . . . . . . . . . 357-194A
Inductive Tachometer
890-909C TACHOMETER, INDUCTIVE
Attaches to the spark plug on single and twin cylinder
engines for checking engine speed. Engines operating at
optimal speed stay cooler and preform better.
25686
35490
Folding Soft Top Canopy
Figure 4-1
Head Light Kit
Refer to Figure 4-2:
Make seeing easier when completing a job after
sundown and when parking your mower in a shed that is
not well lit by attaching Land Pride’s Light Kit.
Z Mower Light Kit . . . . . . . . . . . . . . . . . . . . . 357-160A
Light Kit
Figure 4-2
Mulching Kit & Blades
Refer to Figure 4-3:
Give your lawn that fresh cut grass look without those
unsightly grass clippings showing by installing mulching
blades (item #9) and Mulching Kit (Items #1 to #8) on
your mower deck.
NOTE: Mulching Kit includes baffles and mounting
hardware only. (Mulching Blades sold separately)
For ZT60i mowers with S/N 748110+
ZT60i Mulching Blades (Set of 3 blades) . . . . 310-469A
ZT60i Mulching Kit (Baffles & Hardware). . . . 357-573A
For ZT72i mowers with S/N 748110+
ZT72i Mulching Blades (Set of 3 blades). . . . 310-473A
ZT72i Mulching Kit (Baffles & Hardware). . . . 357-577A
33822
Mulching Kit (Mulching Blades Shown)
Figure 4-3
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
Section 5: Maintenance & Lubrication
Maintenance
Regular maintenance is the best prevention for costly
downtime or expensive, premature repair. The following
pages contain suggested maintenance information and
schedules which the operator should follow on a routine
basis.
!
DANGER
Exercise caution when working under the deck as the mower
cutting blades are extremely sharp. Wearing gloves is
advisable when working around or with cutting blades.
Check initially and periodically for loose bolts and pins.
signaling a problem. Visually inspect machine for any
abnormal wear or damage. A good time to detect
potential problems is while performing scheduled
maintenance. Correcting problems as quickly as
possible is the best insurance.
!
WARNING
Read and observe all safety warnings in this manual and in the
engine service manual.
!
WARNING
Except when checking or changing components, always keep
protective shields on for safety as well as for cleanliness.
Clear away heavy build-up of grease, oil, and dirt,
especially around the engine and under the seat
platform. Minute dust particles are abrasive to
close-tolerance engines and hydraulic assemblies.
!
WARNING
Keep your machine clean. Remove all deposits of trash and
clippings. A dirty machine can cause engine fires and
hydraulic overheating as well as excessive belt wear.
Inspect mower daily for grass clippings, tangled wire and
string. The underside of the mower deck will collect a
build-up of grass clippings and dirt, especially when
grass is wet or has high moisture content. This build-up
will harden, restricting blade and air movement and will
usually produce a poor quality of cutting. Therefore,
debris should be routinely removed from under the deck.
To do this, it will be necessary to raise and block the deck
in the full up position before scrapping build-up from
underneath.
!
WARNING
DO NOT have engine running when servicing or making
adjustments to the mower. Shut blade engagement switch off,
move both control levers out, set park brake on, shut engine off
and remove ignition switch key.
Some repairs require the assistance of a trained service
mechanic and should not be attempted by unskilled
personnel. Consult your Land Pride dealer when
assistance is needed.
!
WARNING
When possible, clean under the deck using a stick or similar
instrument making sure that no part of the body, especially
arms and hands are under the mower.
Maintenance Safety
!
WARNING
Keep mower properly maintained. Do not make unauthorized
modifications. An improperly maintained mower or one that
has been improperly modified can be dangerous to operate.
!
DANGER
Repairs or maintenance specifically requiring engine power
should be performed by trained personnel only. Control levers
should be out. If control levers are to be operated, the tires
should be properly supported off the floor. Enclosed areas
should be properly ventilated to prevent carbon monoxide
poisoning.
!
WARNING
Do not operate mower with loose pins, bolts, and nuts. Loose
hardware can result in a serious breakdown causing bodily
injury or death.
!
DANGER
Tires
Before working on or under the deck, make certain blade
engagement switch has been shut off, deck has been properly
blocked up, engine has been shut off, and ignition switch key
has been removed for maximum safety.
IMPORTANT: Use only tires recommended by Land
Pride. Solid fill tires are not to be used on Zero Turn
Mowers.
Repairs or maintenance requiring engine power
should be performed by trained personnel only.
It is important for your safety and the safety of others that
the tires have correct air pressure. Check air pressure in
all four tires before each use. Visually inspect tires for
loss of air throughout each day of operation. See “Tire
Inflation Chart” on page 59 for correct tire pressure.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
Maintenance Schedule
Every
25 Hrs
Every
50 Hrs
Every
Every
Every
Refer to
Page
Service at Intervals Indicated
100 Hrs 200 Hrs 500 Hrs
Clean Mower, Deck & Engine Cooling System
Verify Safety Start Interlock System
Inspect Unit For Loose Hardware & Damage
Visually Inspect Tires
Daily (After engine has cooled.)
Daily (Before each use)
Daily (Before each use)
Daily (Before each use)
59
Check Engine Oil Level
Daily (Before each use & every 4 hours thereafter)
Daily (Before each use & every 4 hours thereafter)
Daily (Before each use)
Clean Engine Air Intake Screen
Check Fuel Level
43
Inspect Fuel System For Leaks
Check Blades - Sharp & Securely Fastened
Daily (Before each use)
Daily (Before each use)
Check Discharge Chute -
Daily (Before each use)
Make Sure It Is Properly Secured In Place
Grease Blade Spindle Bearings
Change Engine Oil & Filter (1)
Clean Cylinder & Head Fins
Check Battery Connections
X
X
X
X
X
X
X
X
59
Check Tire Pressure
Clean Engine Exterior (3)
Check Transaxle Oil Level
58
Tighten Lug Nuts On Wheels (2)
Grease Front Suspension Pivot
Grease Caster Wheel Bearings
Check Ground & Deck Belt Tension (4)
Check Transaxle For Oil Leaks (5)
Change Fuel Filter (3)
X
X
X
X
X
Grease Deck Lift Points & Struts (8)
Replace Spark Plugs (3)
X/M
X
Replace Air Cleaner Paper Element (6)
Inspect Tethered Fuel Caps (8)
Change Transaxle Oil & Filter (7) (8)
Check & Adjust Parking Brakes (8)
X
X/A
X/A
X/A
NOTES:
1. Initial engine oil and oil filter change is after the first 5 hours of operation. Thereafter, change engine oil and oil filter
every 50 hours of operation. Change every 25 hours when operating the engine under dusty or dirty conditions,
heavy load, high temperatures, and hot weather periods. Refer to Engine Owner’s Manual.
2. Torque lug nuts initially and after first 2 hours of operation.
3. Remove cooling shrouds and clean cooling areas. Check oil cooler fins and clean as needed. Refer to Engine
Owner’s Manual.
4. Inspect ground and deck belt tensions every 6 months or 100 hours and replace if worn or cracking is noticed.
Otherwise, replace every 200 hours or 2 years whichever comes first.
5. Inspect transaxles for oil leaks. Have your nearest Land Pride Service center make repairs as needed.
6. Replace air cleaner filter element if damaged, every 200 hours or every season (whichever comes first). Replace
more frequently when used in dusty conditions.
7. Initial Transaxle oil and filter change is between 25 and 50 hours of operation.
8. X/M = Service per hours indicated in column or monthly (whichever comes first).
X/A = Service per hours indicated in column or annually (whichever comes first).
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
Torque Requirements
Electrical System
“Additional Torque Values” at the bottom of the chart
for exceptions to standard torque values.
Refer to Figure 5-2:
The mower is equipped with a 12 volt negative ground
electrical system powered by a battery located just left of
the engine. When worn out, replace battery with a
maintenance-free garden mower 12 volt BCI group
UL1HD with 245 cold cranking AMPs (CCA) or U1L-X
with 300 CCA. Follow manufacturer’s maintenance,
safety, storing, and charging specifications.
!
WARNING
Particular attention must be given to tightening the drive
wheel lug nuts, blade spindle bolts, electric clutch bolt and
transaxle mounting bolts and nuts. Not torquing these
components correctly can result in the loss of a wheel, blade
or burnt clutch. Any of the above situations can cause serious
damage to the equipment and/or personal injury.
Red Battery
Cable (+)
12 Volt Battery
It is recommended that the following be checked after the
first 2 hours of initial operation and after removal for
repair or replacement. Thereafter, they should be
checked every 50 hours of operation.
• Electric Clutch bolt (See item (#13) in Figure 5-6 on
page 37).
• Wheel lug nuts (See item (#6) Figure 5-7 on page 38)
• Transaxle mounting bolts (See item (#3) Figure 5-7 on
page 38)
Refer to Figure 5-1:
Black Battery Cable (-)
• Retighten choke and/or throttle cable clamp screws to
35 in-lbs if they work loose or are loosened to make
cable adjustments.
33760
Battery
Figure 5-2
• See engine owner’s manual for all other engine torque
values.
!
WARNING
Incorrect battery cable connections can damage the mower’s
electrical system and cause battery cables to spark. Sparks
around a battery can result in a battery gas explosion and
personal injury.
• Always disconnect negative (black) cable from battery
before disconnecting positive (red) cable.
• Always reconnect positive (red) cable to the battery’s
positive (+) post before reconnecting negative (black) cable
to the battery’s negative (-) post.
!
WARNING
Keep battery terminals from touching any metal mower parts
when removing or installing battery. Do not allow metal tools
to short between battery terminals and metal mower parts.
Shorts caused by battery terminals or metal tools touching
metal mower components can cause sparks. Sparks can cause
a battery gas explosion which can result in personal injury.
Tighten Choke and Throttle Cable
Clamp Screws to 35 in-lbs.
33901
Choke and Throttle Cable Clamp Screws
Figure 5-1
!
WARNING
Acid can cause serious injury to skin and eyes. Avoid skin
contact with battery acid and always wear eye protection
when checking the battery. Flush area with clean water and
call a physician immediately. Acid will also damage clothing.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
!
WARNING
Do not overfill battery. Electrolytes may overflow and damage
paint, wiring and structure. Use soap and water when
cleaning the battery. Be careful not to get soap and water into
the battery. Use soda mixed in water to clean corrosion off the
terminals.
20 Amp Fuse
White Wire Leads
10 Amp Fuse
Purple Wire Leads
!
WARNING
Do not allow an open flame near the battery when charging.
Hydrogen gas forms inside the battery. This gas is both toxic
and flammable and may cause an explosion if exposed to a
flame.
Common circuit problems are usually caused by
electrical shorts, corroded, or dirty terminals, loose
connections, defective wire insulation, or broken wires.
Switches, solenoids, and ignition components may also
fail, causing a short or open circuit.
Relay Switch
Wiring Harness Fuses
33902
Refer to Figure 5-3:
Figure 5-3
The relay switch is for the starter circuit. The electrical
system is protected by fuses located along the wire
harness beneath the seat pan latch near the relay switch.
The fuses are:
• Clutch Engagement - 10 Amp, blade type
• Main Electrical System - 20 Amp, blade type
Refer to Figure 5-4:
Uncovered Red
10 Amp Fuse
To diagnose the electrical system, a general
understanding of electrical servicing and use of basic
test equipment is necessary for troubleshooting and
making repairs. Major overhaul or repair of starter motor
and charging system should be performed by trained
technicians only. The following checks should be
preformed if an electrical problem exist.
Uncovered Amber
20 Amp Fuse
33903
Fuses Shown With Cover Removed
Figure 5-4
1. Remove fuse covers to access fuses. Visual inspect
each fuse for a broken circuit. A test light can be used
to check current across fuse terminals or remove the
fuse in question and use an ohm meter to check for
continuity across its terminals.
2. If fuses are good, use a voltmeter to check battery
voltage. Recharge or replace battery if battery
voltage is low.
3. If battery voltage is satisfactory, check cleanliness
and tightness of terminals and ground connections.
4. If terminals and ground connections are clean and
tight, visually inspect for defective wire insulation and
broken wires. If necessary, use a test light to check
for current to the component not operating.
Unplugged
Relay Switch
Refer to Figure 5-5:
Relay Switch
Receptacle
5. If the electrical problem is with the starter motor and
relay switch.
33904
Relay Switch Shown Unplugged
Figure 5-5
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
Deck Drive Belt Removal & Installation
Refer to Figure 5-6:
Belt Maintenance
1. Park mower on a flat surface.
!
DANGER
Before raising floor pan or removing pulley guards, make
certain blade engagement switch has been shut off, deck has
been properly blocked up, engine has been shut off, and switch
key has been removed for maximum safety. Replace all guards
and floor pan before putting mower back into service. Repairs
or maintenance requiring engine power should be performed
by trained personnel only.
2. Make sure blade engagement switch is (OFF),
control levers are fully (OUT), park brake is (ON) and
engine switch key is (OFF) and removed.
3. Place deck height in the lowest position.
4. Remove deck belt covers and raise floor platform.
5. Pull hitch pin (#2).
Refer to Figure 5-6:
6. Release deck belt tension by placing a socket
wrench with a 3/4" socket on the over-center-release
latch (#3) and turning counterclockwise. This will
relieve tension on idler extension spring (#5).
Replace belts that show signs of severe cuts, tears,
excessive weather checking, and cracking or burns
caused by slipping. Slight raveling of belt covering does
not indicate belt damage. Trim ravelings with a sharp
knife.
7. Pull belt tension idler arm (#6) away from deck drive
belt (#11) to provide maximum belt clearance and
remove belt from spring tensioned idler (#8).
Inspect belt pulley grooves and flanges for wear. A new
belt or one in good condition, should never run against
the bottom of the groove. Replace pulley when this is the
case, otherwise belt will lose power and slip excessively.
8. Remove existing belt (#11) from drive pulley (#14).
9. Remove existing belt (#11) from all remaining deck
pulleys.
Never pry belt onto a pulley as this will cut or damage
fibers in the belt covering.
10. Install new belt (#11) in reverse order the belt was
removed using belt routing shown in Figure 5-6.
Keep oil and grease away from belts, and never use belt
dressings. Any of these will destroy belt composition in a
very short time.
11. Re-tension idler pulley (#8) by turning the over-
center-release latch (#3) clockwise until over-center-
release locks in place. Check belt tension per “Deck
12. Re-install hitch pin (#2).
13. Re-install deck belt covers and lower floor platform.
1. Spring eyebolt bracket
2. Hitch Pin
3. Over-center latch
(Use 3/4" socket wrench)
4. Eyebolt
5. Idler extension spring
6. Belt tension Idler arm
7. Blade spindle drive pulleys
8. Idler pulleys
9. Ground drive pulley
10. 1/4" x 1/4" Key
11. Deck drive belt
12. Clutch Locking Bracket
13. Clutch bolt
14. Deck drive pulley with 12V
Electric Clutch (Engages
pulley #2)
15. Lock Washer
16. Thick Washer
17. Latch (Secures pulley
guards)
33781
Deck Drive Belt Layout
Figure 5-6
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
position.
Ground Drive Belt Removal & Installation
1. Park mower on a flat surface.
2. Make sure blade engagement switch is (OFF),
control levers are fully (OUT), park brake is (ON) and
engine switch key is (OFF) and removed.
!
WARNING
Make sure engine and engine muffler are completely cooled
before working on and around the drive belt. Severe burns to
the body could result if engine and muffler have not cooled.
released and tension is re-established.
4. Place deck height in the lowest position.
Refer to Figure 5-7:
be removed from any of the other deck pulleys.
11. Make sure deck drive belt is routed properly on all of
the deck pulleys and then re-tension deck belt idler
instructions on Page 37.
1. Take-up idler arm
2. Spring tension bracket
3. Transaxle mounting bolts
4. Take-up eye bolt
5. Take-up Whiz nuts
6. Wheel lug nuts
7. Take-up Spring
8. Take-up pulley
9. Ground drive pulley
10. Ground drive belt
11. Deck drive belt
12. Neutral return spring
13. Transaxle pump pulleys
14. Deck drive pulley with 12V
Electric Clutch
33782
Ground Drive Belt Layout
Figure 5-7
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
1. Park mower on a flat level surface. Make sure blade
engagement switch is (OFF), control levers are fully
(OUT), park brake is (ON) and engine switch key is
(OFF) and removed.
Hydrostatic Drive System
!
DANGER
Hydraulic fluid under pressure can penetrate skin. Wear
protective gloves and safety glasses or goggles when working
with hydraulic systems. Use a piece of cardboard or wood
rather than hands when searching for hydraulic leaks. If
hydraulic fluid is injected into the skin or eyes, it must be
treated by a doctor familiar with this type of injury within a
few hours or gangrene may result. DO NOT DELAY.
2. Clean transaxle exterior of any debris especially
around the fill port cap. A degreaser may be needed.
3. Remove fill port cap (#8).
4. Oil level should be at the “FULL COLD” line (36) or
about 3/8" deep in the bottom of expansion tank with
o
o
oil temperature between 50 and 100 F. If no oil is
present in the expansion tank, add hydraulic oil until
oil reaches the “FULL COLD” line. Do not overfill.
!
WARNING
5. Install top port cap (#8) and hand tighten.
Always wear adequate eye protection when servicing the
hydraulic system.
6. Recheck oil level once unit has been operating for
approximately 1 minute.
IMPORTANT: Do not use a high pressure washer on
or around the hydraulic transaxles. Water intrusion
will result and void the warranty.
IMPORTANT: The transaxles must be purged if no
oil was present in the expansion tank prior to adding
oil to remove any air that may have become trapped.
NOTE: The transaxle units are equipped with bypass
valves. For more information refer to “Moving Mower
The ZT60i & ZT72i mower are equipped with two
TM
independent Hydro-Gear ZT5400 Integrated Zero-
Turn transaxle units. The units are located beneath the
seat and require oil and filter changes on a regular basis.
Check oil level in the expansion tanks daily. Stop
operations immediately if transaxles are operating hot,
noisy, or lacks power after operating for a short time. Wait
for oil to properly cool and then check oil level in
expansion tanks. If expansion tanks are properly filled
with oil, have your nearest Authorized Land Pride
Service department check the units and make necessary
repairs before putting the mower back into service.
Transaxle Oil Check & Filling
Refer to Figure 5-8:
The mower has two independent hydrostatic transaxles.
Each transaxle will require separate oil checks. It is best
to check oil when oil in the transaxle is between
o
o
50 and 100 F. See page 51 for oil specifications.
IMPORTANT: A transaxle must be purged anytime
oil has been added to the unit or when unit has been
opened to facilitate maintenance.
IMPORTANT: Clean debris from around fill cap
before checking or adding oil to the unit.
33783
NOTE: Be certain to place control arms in the park
position before rotating seat platform up.
Transaxle Oil Check & Filling (Left-Hand Shown)
Figure 5-8
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
e. Tighten oil filter cover to specified torque. See
“Additional Torque Values” on page 58 for
specified torque value.
Transaxle Oil & Filter Change
The mower has two independent hydrostatic transaxle
systems. Each system will require separate oil and oil
filter changes. It is best to change oil soon after using the
mower while dirt particles are still suspended in the oil.
See page 51 for transaxle oil specifications.
Refer to Figure 5-8:
10. Remove top port vent plug (#4). This will allow the
transaxles to vent during oil fill.
Initially, change oil and oil filters after the first 25 to 50
hours of operation. Thereafter, change oil and filters
every 200 hours or every year whichever comes first. Two
filters are required with each oil change. They may be
purchased from your nearest Land Pride dealer. See
page 51 for filter part numbers.
11. Remove expansion tank cap (#8) and fill transaxle by
adding specified oil to expansion tank (#7) until oil
appears at the top port vent plug opening (#4). See
“Hydrostatic Transaxle Specifications &
Capacities” on page 51 for oil type and quantity.
12. Install top port vent plug (#4) and tighten.
13. Continue to add oil to the expansion tank until oil
reaches the full cold line (approximately 3/8" up from
the bottom of expansion tank).
IMPORTANT: The transaxles must be purged after
every oil change. See “Transaxle Purging
NOTE: Fill tube (#5) should be hand squeezed
several times to burp out air and to drain oil from the
expansion tank into the tube. Be careful not to
damage the tube while squeezing it. Use a
protective cloth wrapped around the tube if using a
tool to squeeze such as a pair of pliers.
IMPORTANT: Refer to Figure 5-8 on page 39. Clean
debris from around oil filter cap (#1), oil fill vent port
plug (#4), and expansion tank cap (#8) before
removing any caps and draining hydraulic oil.
1. Park unit on a flat level surface. Stop engine and
remove ignition key. Make sure blade engagement
switch is (OFF). Spread control levers fully apart.
14. Reinstall expansion tank cap (#8) by hand. Be
careful to not overtighten.
Refer to Figure 5-8 on page 39:
15. Wipe off all excess oil. A degreaser may be needed
to remove excess oil.
2. Begin on the left side by placing an oil pan (12" or
more in diameter with approximately 8 qt. or more
capacity) beneath the transaxle oil filter cover (#1).
16. Repeat steps 1 thru 15 for the right side.
3. Clean transaxle exterior and expansion tank of any
debris. A degreaser may be needed.
Transaxle Purging Procedures
It is critical that air is purged from the hydrostatic drive
system to keep it efficient. This is because compression
and expansion rate of air is higher than that of oil.
NOTE: Drain old oil filters of all free flowing oil prior
to disposal. Place used oil and oil filter in
appropriate containers and deliver to an approved
collection facility.
This purge procedure should be implemented any time
the hydrostatic system has been opened to facilitate
maintenance or after oil has been changed.
4. Unscrew oil filter cover (#1) and allow oil to drain.
Symptoms of a hydrostatic system that has not been
purged may be:
5. Remove oil ring (#2) from oil filter cover (#1) and
dispose of oil ring properly.
1. Noisy operation.
6. Remove expansion tank cap (#8) to facilitate
drainage.
2. Lack of power after short term operation.
7. Allow oil to drain until it has slowed to a slow drip. Be
sure to properly dispose the oil.
3. High operation temperature and excessive
expansion of oil.
8. After oil has completely drained from transaxle
housing, remove used oil filter (#3) from transaxle
housing and dispose or properly.
Refer to Figure 5-8 on page 39:
Before purging system, make sure fill tubes (#5) are full
of oil and expansion tanks (#7) are filled to the cold full
line (#6). Squeeze all air from fill tubes and add oil if
expansion tanks are low. See “Hydrostatic Transaxle
Specifications & Capacities” on page 51 for oil
specifications. The following procedures are best
performed with mower drive wheels off the ground and
then repeated under normal operating conditions. If this
is not possible, the procedure should be performed in an
open area free of any objects or bystanders.
9. Install new oil filter per instructions below:
a. Insert new oil filter into transaxle housing.
b. With a clean rag, clean the inside surface of the oil
filter cover that the oil ring seats against.
c. Apply a thin coat of oil on new rubber oil ring (#2)
and install new O-ring onto filter cover (#1).
d. Screw oil filter cover on until it makes contact with
the surface it seats against.
1. Open both transaxle bypass valves (#9) by rotating
the valves counterclockwise to “BYPASS”.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
2. Start engine and place both control levers in neutral.
Slowly move control levers completely forward and
rearward 5 to 6 times.
IMPORTANT: The fuel system can be damaged if
the wrong fuel is used. Never use methanol, lead
gasoline, or unleaded gasoline containing more
than 10% ethanol. Do not mix oil with gasoline.
3. Close both bypass valves by rotating them clockwise
to “RUN”.
Land Pride recommends adding correct amounts of gas
stabilizer/conditioner in the fuel. For best results, follow
engine manufacturer’s directions. Using a fuel stabilizer/
conditioner in the fuel can provide benefits such as:
4. With engine running and control levers in neutral,
slowly move levers forward and reverse 5 to 6 times.
5. Stop engine and check fill tubes (#5) and expansion
tanks (#7). Squeeze all air from fill tubes and add oil
to expansion tanks if they are low.
1. Keeps gasoline fresh during storage of 90 days or
less. Drain fuel tank if storage is longer.
2. Cleans engine during operation.
IMPORTANT: The transaxle is considered purged
when transaxles are at the proper oil level, operate
at normal noise levels, oil temperatures are not
excessively high, and mower does not lack power.
3. Eliminates gum-like varnish build-up in the fuel system.
!
DANGER
6. It may be necessary to repeat Steps 1 to 5 until all air
is completely purged from the system, transaxle
operates at normal noise levels, and travels at
normal speeds.
• Replacement of fuel system parts (i.e. gas caps, hoses, fuel
tanks, fuel filters, etc.) must be the same as original parts.
Fire and/or explosion can occur if not followed.
• Observe safe fuel handling precautions. Fuel is flammable
and vapors are very explosive. An explosion or fire can
burn, destroy and kill property, animals and people.
• Do not fill tank with engine running or while engine is hot.
Allow engine to cool before filling. Fuel spilled over engine,
muffler, or hot objects may result in a fire or explosion.
• Allow engine to cool before servicing the fuel system.
• Do not smoke while handling fuel or around the fuel tanks.
• Do not fill fuel tanks to the top. Fuel will expand in hot
weather and seep out through the fuel tank vent system.
• Screw gas cap on immediately after filling a tank. Never
operate mower without gas caps installed.
Fuel Cap
Fuel Vent
Valve
• Clean up any gasoline spills immediately.
• Keep fuel away from open flame or spark.
• Store mower away from open flame and sparks.
Fuel Tank
• Refuel outdoors preferably, or in well ventilated areas.
• Never attempt to start the engine when there is a strong
odor of gasoline fumes present. Locate and correct cause.
• Never buy more than a 30 day supply of gasoline and store
it in an approved container out of children’s reach.
• Do not fill gasoline containers inside a vehicle, on a truck,
or on a trailer. Interior carpets and plastic truck bed liners
insulate the container and slow loss of static charge.
• When practical, remove equipment from the truck or trailer
and refuel the equipment with its wheels on the ground. If
this is not possible, then refuel the equipment on the truck or
trailer using a portable container and not a gasoline
dispenser nozzle. If a gasoline dispenser nozzle must be
used, keep nozzle in contact with rim of fuel tank or
container opening at all times until fueling is complete.
• Gasoline is a poison that is harmful or fatal if swallowed.
• Avoid prolonged breathing of vapors. Long-term exposure
to vapors can cause serious injury and illness.
Fuel Sight Gauge
33784
Fuel Tanks (Left Side Shown)
Figure 5-9
Fuel System
Refer to Figure 5-9:
The fuel tanks are located in the mower fenders. Total
capacity of each fuel tanks is 6 U.S. gallons. Fill tank
when fuel shows low in the fuel sight gauge. Before
filling, push blade engagement switch (OFF), move both
control levers (OUT), set park brake (ON), and turn
switch key (OFF). Allow engine to cool before filling tank.
Clean dirt from around fuel tank cap. Remove cap and
begin filling. Do not fill fuel tank to the top. Fuel will
expand in hot weather and seep out through the fuel tank
vent system. When finished, screw cap back on until it
makes a clicking noise and ratchet action that can be
heard and felt when tight. Wipe up any spilled gasoline.
Use regular unleaded gasoline with an (R+M)/2 octane
rating of 87 or higher.
• Keep face away from nozzle and gas tank opening.
• Keep gas away from eyes and skin.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
Evaporative Emission Control
System
Drain Fuel Tank
Refer to Figure 5-11:
Refer to Figure 5-11:
1. Park unit on a flat surface. Make sure blade
engagement switch is (OFF), both control levers are
(OUT) and park brake is (ON). Stop engine and
remove ignition key.
All Land Pride Zero Turn Mowers are EPA compliant as of
January 1, 2012 production date and include a decal
located on right side of engine stating the following: “This
Equipment meets U.S. EPA Evap. Standards”.
2. Disconnect negative battery cable from the battery.
3. Trace fuel line from tank to be drained to the
Left/Right Fuel Tank Valve located on right side of
seat. Remove fuel line hose clamp at the Left/Right
Fuel Tank Valve and remove fuel line.
This Evaporative Emission Control System requires no
regularly scheduled maintenance but should be
inspected periodically, and thoroughly examined at least
once a year at the beginning of the mowing season:
4. Place end of fuel line into a gas can or a drain pan to
drain fuel tank.
1. Inspect all fuel system components including tanks,
vents, hoses, clamps, fuel filter, valves, and fittings
for leaks, cracks, and loose connections. Make
repairs as necessary.
5. When fuel tank is drained, reattach fuel line to the
left/right fuel tank valve with previously removed
hose clamp.
2. The fuel tank is equipped with a tethered cap. Ensure
tether is present and secured to the cap.
3. The fuel cap has been designed to provide audible
and tactile feedback indicating that proper sealing
has been achieved. Ensure that this function is
present and that no fuel leaks from the filler neck
during usage. If fuel leakage is ever noticed at this
point, the fuel cap must be replaced immediately.
Fuel Filter
Refer to Figure 5-12 on page 43:
!
DANGER
Left/Right Fuel Tank Valve Center
Position “O” as Shown is OFF
Empty fuel tank before replacing fuel filter to keep fuel from
leaking out and creating a fire/explosion hazard.
The fuel filter is installed in the fuel line between the
fuel tank and engine fuel pump. Location of fuel filter will
vary depending on which engine your mower is equipped
with. See engine owner’s manuals for exact location of
fuel filter and instructions on removal and installation.
Hose Clamps
Refer to Figure 5-10:
Replace fuel filter annually at the beginning of each
mowing season or after every 100 hours of operation,
whichever occurs first. (A plugged filter is considered a
maintenance item.) This will keep the fuel filter from
becoming plugged causing poor engine performance
and unexpected downtime. Be sure to install filter with
Flow Arrow pointing towards engine side of fuel line.
Left Tank Fuel Line
Engine Fuel Line
Right Tank Fuel Line
33812
Fuel Lines (Raise Seat Platform to Access)
Figure 5-11
(Flow Arrow) Indicates direction
fuel must flow through the filter.
General Engine Maintenance
Detailed instructions and recommendations for break-in
and general maintenance are specified in the Engine
Operator’s Manual. Please refer to this manual for engine
servicing, lubricating oil levels with capacity and viscosity
recommendations, bolt torques, etc. The engine
warranty is backed by the engine manufacturer.
Special attention should be paid to applicable data which
is not duplicated here.
23803
Fuel Filter
Figure 5-10
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
Change Engine Oil
Refer to Figure 5-12:
Engine Oil & Oil Filter
Refer to Figure 5-12:
See “Engine Specifications & Capacities” on page 51
and “Engine Operator’s Manual” for oil type, capacity
and maintenance schedule. Check oil daily and after ever
4 hours of operation. Mower must be sitting level when
checking oil. Change engine oil and oil filter after the first
54 hours of operation and per engine manufacture’s
recommendations thereafter. Change oil more frequently
if mower is operated in extremely dirty conditions.
1. Park unit on a flat surface. Make sure blade
engagement switch is (OFF), both control levers are
(OUT) and park brake is (ON). Stop engine and
remove ignition key.
2. Place a suitable container on the ground beneath oil
drain valve (#3).
3. Unscrew oil drain valve (#3) until oil flows freely and
valve head offers some resistance. Do not unscrew
valve any farther.
IMPORTANT: Make certain engine is level and you
are inserting the dipstick correctly when checking
oil. Incorrect oil levels can cause engine problems.
4. Remove oil filter (#4) and let remaining oil drain out.
Make certain the existing O-ring is not stuck to filter
base (#2). Discard existing O-ring and filter in a
manner that is compatible with the environment.
Check Engine Oil
Refer to Figure 5-12:
5. Clean engine oil filter base (#2). Coat new oil filter
O-ring with clean engine oil and screw new oil filter
(#4) onto engine oil filter base.
1. Park on a level surface, shut engine off and allow
time for oil to cool and drain into the sump.
2. Clean area around oil fill cap/dipstick (#1) of dirt and
debris before removing it. Unscrew oil fill cap and
wipe dipstick clean.
6. Hand tighten new oil filter until O-ring seats against
oil filter base. Finish tightening by turning filter to the
specifications provided in the Engine Operator’s
Manual.
3. Check oil level on dipstick by insert dipstick fully in
without screwing it in and removing again to check
oil level.
7. Retighten drain valve (#3).
8. Dispose of used motor oil in a manner that is
compatible with the environment. Do not throw used
oil in the trash, pour it on the ground, or down a drain.
4. If oil level on the dipstick is near or below lower limit
mark on dipstick, add recommended oil until it
reaches the full mark. Do not overfill.
9. Fill engine with the correct oil and quantity provided
in the Engine Operator’s Manual and specifications
5. Reinstall oil filler cap/dipstick by screwing it in firmly.
10. Replace oil fill cap/dipstick, start engine and check
oil filter for leaks.
11. Stop engine and check oil level. See “Check Engine
Oil” on this page.
1. Oil Fill Cap/Dipstick
2. Oil Filter Base
3. Oil Drain Valve
4. Oil Filter
5. Oil Cooler
6. Tail Pipe Clamp
7. Muffler Tail Pipe
8. Cooling Fan
9. Rain Cap
10. Air filter
11. Burp Valve
12. Muffler
13. Fuel Filter
14. Starter
33816
Engine Components
Figure 5-12
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
Engine Air Filter
Refer to Figure 5-13:
Rain Cap - Positioned Vertically
on Top of Air Filter Canister.
A specially designed dry filter is standard equipment and
supplies clean combustion air to the engine. Perform
engine air filter maintenance per the Engine Operator’s
Air Filter Inner Element
Air Filter Outer Element
IMPORTANT: Do not operate engine with a
damaged air filter or without air filter elements. Dirt
will enter engine causing dust induced engine
damage.
Canister Cap
Canister
Open Ends of Filter
IMPORTANT: Do not block air intake to canister
such as placing an object in front of the air intake
opening.
Elements Face Canister
1. Replace filter element every 200 hours or every year,
(whichever comes first). Service more frequently
when used in dusty conditions.
Burp Valve - Position Below Air Filter Canister
27851
2. Release retaining clips and remove filter element.
Clean canister with a damp cloth.
Canister Air Filter Kawasaki Engine
Figure 5-13
3. Before installing a new filter element, inspect it by
placing a bright light inside and rotate the element
slowly, looking for any holes or tears in the paper.
Also check gaskets for cuts or tears. Do not attempt
to use a damaged element which will allow abrasive
particles to enter the engine.
IMPORTANT: Burp valve must be positioned below
the canister to make certain it drains water away
from the filter elements properly.
7. Reinstall canister cap with burp valve positioned
below the canister. Make sure it seals all around the
canister before latching retaining clips.
4. Inspect Burp Valve. Replace burp valve if it is
cracked, torn, stays open, or is missing. See also
“Burp Valve” on this page.
8. Check all fittings and clamps periodically for
tightness. Inspect hoses for holes or cracks.
5. Install new Inner element into the new outer element
as shown in Figure 5-13.
9. Periodically check engine intake hose for signs of
ingested dust. Locate and repair source of ingested
dirt.
6. Install new outer filter element by inserting the open
end in the canister first.
10. Never operate a machine without an air filter
installed.
Burp Valve
Refer to Figure 5-14:
The burp valve is a highly important part of your dust filter. It opens and shuts expelling collected dust and water as
the engine’s vacuum pressure pulsates. It also dumps dust collected in the filter canister when the engine stops
running. If the burp valve is damaged, dust that would normally be discharged from the canister can collect on the
filter element causing its life to be shortened. Replace the burp valve if it is open, cracked, torn, or missing.
27786
Normal
Open
Cracked
Torn
Missing
Figure 5-14
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
Improper Installation
Engine Air Filter Handling
Refer to Figure 5-13 on page 44:
Improper installation occurs when dust leaks past the
seals. The filter element must be aligned within the
canister and properly seated on both ends to prevent dirt
from entering the engine.
Prevent costly and non-warrantable premature engine
damage by maintaining the air filter properly. Many
engine problems are due to improper handling of the air
filter. Dust and dirt that gets past the air filter will damage
engine cylinder, piston and bearings in a few hours.
Avoiding the following common mishandling:
Damaged Air Filtering System
A damaged air filtering system occurs from mishandling
of the filter element and operating the mower in areas
that could damage the canister.
• Over servicing
• Improper installation
• Damaged air filtering system
• Incorrect air filter element
Over Servicing
Banging and/or bumping the filter element against a solid
object such as a tire or blowing the element with air can
damage the seals and/or force dust and dirt particles
through the filter media creating a hole for dirt to pass
through to the engine.
Over servicing occurs when an air filter element is
inspected and/or replaced too often. Dust and dirt can fall
off the filter element onto the canister where it can be
sucked into the intake system. Only a few grams of dirt
getting into an engine during each filter inspection can
prematurely produce dust induced engine damage. A
partially dirty air filter element is not harmful to the
engine.
Driving the mower carelessly over rough terrain, jutting
sticks, heavy brush and severe rocks can damage the air
cleaner canister. Periodically inspect the outside of the
air cleaner canister for external damage and replace if
necessary.
Incorrect Air Filter Element
The air filter must remain intact to block passage of dirt
and foreign particles. It must be of sufficient size and
construction to withstand stresses, caused by rapid
cycling of air volume demanded by the engine, without
cracking or tearing under fatigue and pressure. Its filter
elements must have the correct media composition, filter
area, micron size and dimensions to properly filter the air
of dirt while at the same time passing sufficient air to the
engine.
The air filter element should be changed before it
becomes too dirty and restricts air flow to the engine
hindering its performance. Replace the air filter element
immediately should this happen. Engines that do not get
proper amounts of air will draw in excessive amounts of
gas causing premature engine damage.
The frequency of the air filter needing changing is largely
determined by operating conditions. Dusty conditions will
require more frequent servicing.
Land Pride and the engine manufacturers have carefully
selected a reliable filter designed to fit these needs.
Always use genuine Land Pride filters. Failure to use
original equipment replacement parts is an
alteration and will not be considered for warranty in
the event of a dust induced engine damage. See
“Engine Specifications & Capacities” on page 51 for
Land Pride air filter replacement numbers.
A dirty filter element should always be replaced with a
new element. Improper cleaning procedures can get dust
on the inside of the filter causing dirt induced and engine
damage. The air filter warranty expires upon cleaning
or servicing a used filter in any manner. Land Pride
does not warranty a dust induced engine damage if a
used air filter element has been cleaned or serviced
in any manner.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
Blade Sharpening
Mower Blade Maintenance
Blade Inspection
Check mower blades daily, they are the key to power
efficiency and well groomed turf. Keep them sharp as a
dull blade will tear rather than cut grass, leaving a brown
ragged top on the grass within a few hours. A dull blade
also requires more power from the engine.
!
DANGER
Keep blades balanced when sharpening. An unbalanced blade
may come loose and fly out from under the deck. Also, an
unbalanced blade will shorten the spindle bearing’s life.
Replace any blade which is bent, cracked, or broken.
!
CAUTION
ALWAYS wear eye protection and gloves when sharpening a
blade.
!
WARNING
DO NOT try to straighten a blade that is bent. Never weld a
broken or cracked blade. ALWAYS replace with a new Land
Pride blade to assure safety.
NOTE: Care should be taken in order not to remove
any more material than necessary to sharpen blade.
1. Clean blade, blade washer and mounting surface of
all debris before inspecting blade and sharpening.
!
DANGER
Never work with blades while engine is running or with blades
engaged. Always push blade engagement switch down (OFF),
move both control levers to neutral and then fully (OUT), set
park brake (ON), and turn engine (OFF). Block up mower
when you must work under it. Wear gloves when handling
blades. Always check for blade damage if mower should strike
a rock, branch, or other foreign object during mowing.
Refer to Figure 5-16:
2. Lay blade on a flat surface and check blade to make
sure it is not warped. Replace any blade that is
warped.
Blade Removal
Refer to Figure 5-15:
Warped Blade (Replace)
Cutting Plane
IMPORTANT: Blade mounting bolts have right hand
threads. Turn blade bolts counterclockwise to loosen
and clockwise to tighten.
Straight Blade
24579
1. Remove mower blade (#4) by grasping blade end
with a rag or thick padded glove while loosening
blade bolt (#2) with a 3/4" wrench.
Comparison of Warped & Straight Blades
Figure 5-16
2. Remove 1/2" blade bolt (#2), blade washer (#3) and
mower blade (#4) from spindle assembly (#1).
Refer to Figure 5-17:
3. Lay blade on a flat surface and check both ends of
blade to make sure it is not twisted. Replace any
blade that is twisted.
24579
Cutting Edge
Twisted Blade (Replace)
Cutting
Plane
Cutting Edge
Cutting Edge
Straight Blade
Comparison End View of Twisted & Straight Blades
Figure 5-17
2
33813
4. Check blade cutting edge. Replace blade if nicks are
severe. Blade may be sharpened if cutting edge is
dull or slightly nicked.
Blade Removal & Installation Illustration
Figure 5-15
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
Refer to Figure 5-18:
Refer to Figure 5-20:
6. Remove an equal amount of material from each end
of the blade to keep blade in balance. Check blade
balance as follows:
NOTE: New mower blades are furnished with
cutting edge parallel with back of blade. Do not
sharpen blade to original parallel pattern. It is easier
to get a straight cutting edge by resharpening the
pattern to the one shown in Figure 5-19.
a. Positioning center of blade horizontally on a nail
or shaft. See Figure 5-20.
b. If either end of the blade rotates downward, grind
(remove) metal on that end until blade will
balance horizontally on the nail or shaft.
c. Resharpened blades can be installed after they
have been properly sharpened and balanced.
HORIZONTAL
Original Cutting Edge Pattern
NAIL OR SHAFT
Blade Balancing
19075
19046
Blade Resharpening
Figure 5-18
Figure 5-20
Refer to Figure 5-19:
5. Sharpen blade by following the grinding pattern
shown in Figure 5-19.
Blade Installation
Refer to Figure 5-15 on page 46:
a. Grind cutting edge at the same bevel as the
original angle. (27 1/2 degrees).
!
WARNING
b. Sharpen only the top of the cutting edge to
maintain sharpness.
When mounting blades, rotate them after installation to ensure
blade tips do not touch each other or sides of the mower.
c. Touch-up sharpening can be done with a file.
!
WARNING
Failure to torque blade bolt properly may result in the blade
coming loose and falling off causing a serious injury.
IMPORTANT: Replace mower blades with Land
Pride blades only.
Resharpening Cutting Edge Pattern
IMPORTANT: Always install blades with cutting
edge facing direction of blade spindle rotation and
with wing tips pointing up towards bottom of deck.
For correct blade rotation, see arrow in Figure 5-15.
19074
Blade Resharpening
Figure 5-19
IMPORTANT: Do not re-use blade bolts which have
stripped, worn or undercut threads. For proper blade
bolt torque value. see “Additional Torque Values”
on page 58.
1. Install resharpened or new blade (#4) with blade
washer (#3) and blade bolt (#2). Be careful not to
cross thread blade bolt while installing it.
2. Tighten blade bolt to the correct torque. See
“Additional Torque Values” on page 58 for correct
torque values.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
8. Store mower in a clean, dry place.
End of Season & Long Term Storage
Take the following steps when storing mower at the end
of the season and when unit will not be used for long
periods to ensure readiness for the next mowing season.
9. Block mower up so weight is off the tires.
NOTE: Do not deflate tires.
10. Protect battery from freezing temperatures.
Disconnect the negative ground wire from battery to
reduce chances of a slow electrical drain.
Occasionally recharging battery during storage will
extend battery life.
IMPORTANT: Do not use a high pressure washer on
or around the hydraulic transaxles. Water intrusion
will result and void the warranty.
1. Remove all grass, dirt, trash, and grease that may
have accumulated on the mower and moving parts.
New Season Preparation
The following service is required before starting the
mower after storing it for a season:
2. Scrape off compacted dirt, trash, and grass clippings
from the deck underside. A coating of oil may also be
applied to the deck underside to minimize oxidation.
3. Clean and touch up all scrapes with Land Pride spray
paint.
IMPORTANT: Do not use a high pressure washer on
or around the hydraulic transaxles. Water intrusion
will result and void the warranty.
4. Check blades and blade bolts for wear and replace if
necessary.
1. Clean mower, removing trash and dirt accumulation.
2. Check engine oil level.
5. Check thoroughly for any worn or damaged parts
that need replacing and order them from your
nearest Land Pride dealer.
3. Tighten any bolts that have loosened and make sure
all hair pins, cotter pins, and clevis pins are in place.
6. Thoroughly lubricate machine, according to
lubrication instructions.
4. Install all safety shields and review safety
precautions listed in this manual.
7. Prepare engine for storage:
5. Check and inflate tires to correct psi provided in
a. Run engine for a minimum of 15 minutes.
“Tire Inflation Chart” on page 59.
b. Drain oil from crankcase while engine is still
warm.
6. Fill fuel tank with fresh gasoline.
7. Reconnect spark plug leads to spark plug.
c. Refill with fresh oil of proper viscosity. Refer to
51.
8. Run machine at half speed for 5 minutes, checking
operation of the control levers. Stop engine and
check for oil leaks, loose fittings, and so forth.
d. Drain fuel tank and run engine until it stops from
lack of fuel. Gasoline evaporates if left in
carburetor for long periods, forming gum and
varnish deposits in the carburetor. These deposits
will cause engine flooding and loss of power.
f. Remove and replace fuel filter if not done in the
previous 100 hours.
g. Remove spark plugs and pour a tablespoon of
engine oil into each spark plug hole. Install plugs,
but do not reconnect plug leads.
h. Crank engine with starter at least a dozen
revolutions to distribute oil over cylinder walls and
valve mechanism.
i. Clean dirt and chaff from cylinder fins, blower
housing and muffler.
j. Clean exterior surface of engine. Spread a light
film of oil over any exposed metal surfaces of
engine that are subject to corrosion.
k. Check oil fill cap and fuel tank caps to make
certain they are securely in place.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
Lubrication Points
Lubrication
Legend
Multi-purpose
spray lube
Multi-purpose
grease lube
Multi-purpose
oil lube
50
hrs
Intervals in hours at which
lubrication is required
25
Hours
Left Blade Spindle
Access through rubber slit in pulley cover.
1 - Zerk
Type of Lubrication: Multi-purpose Grease
Quantity = As required
33764
25
Hours
Right Blade Spindle
Access through rubber slit in pulley cover.
1 - Zerk
Type of Lubrication: Multi-purpose Grease
Quantity = As required
33761
33818
25
Hours
Center Blade Spindle
Lower Deck fully down to access under floor platform
1 - Zerk
Type of Lubrication: Multi-purpose Grease
Quantity = As required
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance & Lubrication
33818
100
Hours
Deck Struts
Located beneath floor platform
2 - Zerks (One on each deck strut)
Type of Lubrication: Multi-purpose Grease
Quantity = As required
33819
100/M
Hours
Deck Lift Points
Locate above deck (Deck removed for clarity)
4 - Zerks (2 per side)
Type of Lubrication: Multi-purpose Grease
Quantity = As required every 100 hours or monthly,
whichever comes first.
25
Hours
Front Suspension Pivot
Front Suspension Pivot
Located on front suspension pivot caster
2 - Zerks (One on each front suspension pivot caster)
Type of Lubrication: Multi-purpose Grease
Quantity = As required
Caster Wheel Bearing
100
Hours
Caster Wheel Bearing
Located on hub of caster wheels
2 - Zerks (One on each caster wheel)
Type of Lubrication: Multi-purpose Grease
Quantity = As required
33820
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Specifications & Capacities
Section 6: Specifications & Capacities
Engine Specifications & Capacities
Mower Models
Engine Manufacture
Horsepower
ZT60i & ZT72i
Kawasaki
27
Engine Model Type
Max Torque
FX850V
54.3 ft. lbs.
(73.6 N.m)
Charging System
Starter
12-volt, 13 amp w/Kawaski Engine
12-volt (.8 KW) electric starter w/Kawaski Engine
Ignition
Electronic
Governor
Mechanical
Unleaded gasoline with octane rating of 87 or higher
Oil Cooler
Fuel Type
Oil Cooling
Engine Cooling
Engine Type
No of Cylinders
Displacement
Air cooled, Fly-wheel fan
4-stroke OHV, V-twin cylinder, gasoline
2
52 cu. in.
(852cc)
Compression Ratio
Spark Plug No.
8.2:1
BPR4ES (NGK)
2.1 US quarts
SAE 10W-30
831-034C
Oil Capacity with Filter Change
Oil Type
Oil Filter Part No.
Fuel Filter Part No.
831-031C
Commercial Remote Air Filter:
Inner Filter Part No.
839-973C
839-974C
Outer Filter Part No.
Hydrostatic Transaxle Specifications & Capacities
Mower Models
ZT60i & ZT72i
TM
Transaxle Model Nos.
Gear Type
ZT-5400
Cut Steel Gears
5
Number of Wheel Lugs
Traction Drive Type
Dual Hydrostatic Transmission
Two variable displacement, axial piston type.
V-belt drive from engine crankshaft
71943
Hydraulic Motor/Pumps
Hydraulic Motor/Pump Drive
Hydraulic Oil Filter Part Number
Hydraulic Oil Type
SAE 20W-50 engine oil
Hydraulic Oil Capacity - Per Side
164.8 -166.5 fl. oz. (1.287 - 1.301 gals.) to fill transaxle
General Specifications & Capacities
Mower Models
ZT60i
ZT72i
Weight
1130 lbs. w/vinyl seat
1150 lbs. w/deluxe seat
1150 lbs. w/vinyl seat
1170 lbs. w/deluxe seat
Width of Cut
60"
72"
Cutting Height
1" to 5" in 1/4" increments
Trim Capacity (left side)
8 1/4"
13 1/2"
Specifications to continue on next page.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
Download from Www.Somanuals.com. All Manuals Search And Download.
2/06/14
51
Section 6: Specifications & Capacities
General Specifications & Capacities
Mower Models
Overall width (Chute down)
Overall Width
ZT60i
74 1/4"
ZT72i
86 1/2"
At Rear Tires
AT Deck
52"
74 1/4"
52"
86 1/2"
Overall Length
Overall Height
With ROPS Up
With ROPS Down
88"
91 1/2"
With ROPS Up
75"
With ROPS Down
49 3/4"
Roll Over Protective Structure
Drive Tires
Certified ROPS, includes seat belt
24 x 12.00 - 12, Turf tread
13x6.5 - 6, Rib tire
Front Tires
Hour Meter
Standard equipment
Fuel Capacities
Twin 6 US GAL. tanks (Total fuel capacity = 12 US GAL.)
Twin lever steering provides independent control of each drive wheel
Speed, forward, reverse, brake, and turns
Steering Type
Twin Lever Steering Controls
Steering Turning Radius
Hydraulic Brake Service
Park Brakes
True zero degree. Turns with counter-rotating independent drive wheels
Hydrostatic dynamic braking
Internal wet disk, manual activated
Ground Speed
Forward: 0-12 MPH
Reverse: 0-6 MPH
Wheel Drive
Single V-belt with spring tension idler pulley
Electrical Operated Logic-Control Safety Electric logic-control system governs blade engagement, forward & reverse motion,
Features
engine starting & running, and parking brake functions.
Evaporative Emission Control System
on EPA Compliant Mowers
This equipment uses a sealed fuel system which incorporates a non-vented fuel
cap. Evaporative emissions are vented to the engine where they are combusted
during normal engine operation.
Seat Options
Deluxe cushion seat with arm rests
Optional Suspension seat with arm rest
Mainframe Construction
Drive Motor Mount
Front Caster Wheels
Front Caster Forks
Deck Thickness
Welded steel
Fabricated from 3/16" steel plate
Free turning with sealed for life roller bearings
3/8” steel
3/16" deck with 3/16" reinforcement plate connecting spindle housing mounts
3/16" with solid 1" x 1/4" steel bar for reinforcement.
Solid 1” x 1/4” steel bar for reinforced trim edge.
5 3/16” deep, (room for high-capacity mowing)
Box-Section Reinforced Front Edge
Deck Trim Edges
Deck Housing Depth
Deck Lift
Foot-operated deck height adjustment with transport position
Pin for setting height
Hand Operated Controls
Ignition switch, throttle lever, control levers, park brake lever,
blade engagement switch, choke knob and Fuel Tank Selector Valve
Indicators
Engine warning light and hour meter
Cup Holder
Two cup holders molded into the left side fuel tank
They accommodate nearly any cup size
Cutting Heights
Mowing Blades
Height adjustment in 1/4" increments from 1” to 5”
®
Heavy-duty, heat-treated, high-lift Fusion edge
.25" x 2 1/2" x 21"
18,350 FPM
.25 x 2 1/2” x 25”
18,800 FPM
Blade Tip Speed
Blade Drive
Electric clutch drive with single V-belt to three spindles and spring tension idler
pulley
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Specifications & Capacities
ZT60i = 74 1/4"
ZT72i = 86 1/2"
52"
ZT60i = 8 1/4" & ZT72i = 13 1/2"
88"
75"
49 3/4"
33821
91 1/2"
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Features & Benefits
Section 7: Features & Benefits
ZT60i & ZT72i Models (S/N 748110+)
Features
60" or 72" cutting width
1" to 5" Cutting height
Benefits
Sized right and priced right for ranch, estate owners, and commercial operators.
Provides a good range of cutting heights in 1/4’ increments for any type of turf grass.
57 3/4" Outside drive tire stance Provides excellent stability over uneven and hilly ground along with good maneuverability.
High ground speed Forward 12 mph and reverse 6 mph for high productivity.
Adjustable steering levers with Wide range of adjustments to accommodate almost any size of operator.
comfort grip handles Grips are designed for operator comfort and sustained productivity.
Spring suspension seat platform Helps smooth out the ride.
Strong deck design
New manufactured deck design has a great appearance on the outside, but tough parts on
the inside. 3/16" Deck with 3/16" doubler plate, and a reinforced front edge.
Rapid deck height adjustment
The foot operated with spring assist deck lift and deck stop locator makes for a quick and
easy precise cutting height adjustments.
Easy clean-out deck top
Snap-on Deck Belt Guards
Excellent trim capability
Mid-mount deck design
Floating deck design
Deck allows air and debris move across the top for improved belt cooling and easy clean out.
Deck belt guards can be hand removed easily without tools.
Provides for good trim capability.
Puts deck closer to the operator’s line of sight for more efficient and precise operation.
Chain suspension design provides excellent flotation over uneven terrain.
Two located on deck ends and two located toward mid-decks keeps scalping to a minimum.
Separate expansion tanks eliminating the possibility of cross contamination.
Four anti-scalp rollers
Completely independent
twin hydrostatic drives
Premium wide stance drive tires Provide excellent traction, outstanding side-hill stability and a smooth ride. (24x12.00-12
4ply)
Front ribbed tires mounted in
heavy duty pivoting caster forks
Provide for a quick and durable turning response. (13x6.5-6 ribbed tires)
Electric clutch control
Kevlar drive belts
Provides an easy smooth engagement of the mower blade drive system.
TM
Drive belts made with Kevlar fiber provide long belt life. One hydrostatic pump drive belt
and one deck drive belt.
Stored wrench for assisting belt A wrench stored under the floor platform with 3/4" and 9/16" openings makes belt removal
removal and installation
and replacement easy and possible without carrying extra wrenches.
1" blade spindles mounted in
ductile iron housings
Additional 3/16" plate steel is added to the deck connecting the blade spindle housing
mounts.
Blade spindles, spindle housings and mounts are designed to handle heavy shock loads.
Accessible blade spindle zerks Makes greasing the blade spindles easy.
®
Heavy duty heat treated Fusion Made from highest quality .25” thick fusion treated steel for high wear and increase blade life.
high lift blades
High lift design stands grass up before cutting.
High blade tip speed
Rear side mounted battery
Kawasaki engine
Provides a clean quality cut. (60" deck = 18,350 fpm & 72" deck = 18,800 fpm)
Easy access to battery for servicing and maintaining.
Proven engine to meet customer preferences with power and performance to spare.
Electric start with choke control Keyed ignition and manual choke control are placed for one-handed starting convenience.
Engine oriented for easy access Spark plugs, air filter, oil filter, & oil drain are placed easily within reach.
Center Mounted Rear Engine
Provides maximum mower stability, easy service access, increased leg room, and increased
air flow around engine fins to extend engine life.
Remote Air Intake
All engines come standard with cyclonic type remote air intake to keep engines running clean
and running longer.
Engine oil cooler
Keeps engine running at peak performance in warm weather conditions.
Isolated exhaust muffler
Muffler is hidden and tucked down under to reduce noise and provide protection against
burns.
Ergonomically designed
control console
Instrumentation and console controls are positioned for easy visual or fingertip access.
Hour meter
Measure actual engine run time to monitor service intervals.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Features & Benefits
ZT60i & ZT72i Models (S/N 748110+)
Benefits
Features
Sleek styling EPA approved twin 12 Gallon fuel capacity for plenty of operating range and decreased downtime.
six gallon fuel tanks with sight Extra large fuel openings for easy fueling. Fuel caps are EPA approved, non vented, placed
gauge, extra large tethered fuel inboard and center mounted to protect caps from damage and prevent overflow spills on
caps and vent valve
inclines. EPA vent valve help stops fuel leaks in rollover accidents and sight gauge makes it
easy to see low fuel level in tanks.
Fuel tanks are vented to the
engine carburetor
Engine burns fuel vapors instead of vapors leaking into the atmosphere.
Fuel selector/shutoff valve
Provides on the go switching from one tank to another giving the operator time to finish the
mowing job and to return to the refueling source before the mower stops running. Both tanks
can be shutoff with this valve for servicing and storage.
Molded-in dual cup holders and Tanks are molded with cup holders that fit a wide variety of cups and are in easy access to
storage compartments
the driver. A storage compartment molded next to the cups offer additional operator
convenience.
Lever activated park brake
A manually activated over-center park brake lever located next to the operator’s left side for
easy activation and release of internal wet disk brakes. Mower will not move until brake is
released.
Hinged bayonet mount seat
platform
Tilts up for easy access to battery and drive components.
Comfortable adjustable seat
Deluxe Cushion or Molded Vinyl with suspension and adjustable positioning for operator
comfort and sustained productivity.
Seat safety interlocks
Rising off of the seat with blades engaged will cut engine power and stop blade rotation.
Engine cannot be started with blade engagement switch in “on” position.
Hinged floor platform
Certified ROPS
Provides quick and convenient service access to topside deck components without tools.
Certified ROPS for added operator protection.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 8: Troubleshooting
Section 8: Troubleshooting
Troubleshooting Chart
Probable Causes
Symptoms
Suggested Remedies
Control levers are not in neutral position Place control lever in neutral and fully out.
and fully out.
Starting motor does not crank
engine.
Park brake not engaged (ON).
Engage park brake.
Control lever interlock switch is not
adjusted correctly.
Have your dealer re-adjust the interlock switch.
Blade Engagement switch is engaged.
Weak or dead battery.
Disengage blade switch.
Recharge or replace.
Loose or broken switches
and/or damaged electrical wiring.
Repair or replace switches and electrical
wiring.
Other causes
See Engine Operator’s Manual.
Fill tank.
No fuel in the fuel tanks.
Fuel filter and/or fuel line plugged.
Other causes
Engine cranks but does not start.
Replace fuel filter and/or fuel line.
See Engine Operator’s Manual.
See Engine Operator’s Manual.
Other causes
Engine runs with continuous
misfiring, runs unevenly or runs
erratically.
Dull, bent, or broken cutting blades.
Deck full of wet sticky grass.
Sharpen or replace cutting blades.
Clean underside of deck.
Grass cutting is ragged or uneven
Cutting Blades are not operating at full
engine speed.
Increase engine rpms to full speed (3600 rpm)
Check engine speed with Land Pride Inductive
Tachometer, Part No. 890-909C.
Belt over center take-up is loose.
Worn or broken belt.
Tension over center take-up.
Replace worn and broken belt. See “Belt
Maintenance” on page 37.
Deck is not level.
Check air pressure in all 4 tires
Make level adjustments to the deck.
See “Deck Cutting Height and Leveling” on
Bypass valve is open.
Close bypass valve. See “Moving Mower
with Stalled Engine” page 17.
Loss of power or system will not
operate in either direction.
Bypass assembly is sticking.
Mower is loaded excessively.
Steering hardware is loose or lost.
See your dealer.
Reduce load on mower.
Replace steering hardware.
Bad ground drive belt and/or pump idler Replace belt and/or idler pulley Tighten idler
pulley. pulley if loose.
Loose, lost, or broken belt take-up spring. Reattach or replace belt take-up rod.
Restrictions in air cleaner.
Service air cleaner.
See your dealer.
Internal interference or leakage in
transaxle.
Oil level in transaxle is low.
Poor compression.
Fill transaxle to the correct level.
See your dealer.
Steering linkage is bent or needs
adjustment.
Adjust linkage. See “Steering Adjustments”
Air is trapped in the hydraulic system.
Other causes
Purge transaxle of air or see your dealer.
See Engine Operator’s Manual.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 8: Troubleshooting
Troubleshooting Chart
Probable Causes
Symptoms
Suggested Remedies
Air intake screen or cleaning fins clogged. Clean screen and fins.
Engine is overheating
Not operating engine at rated speed.
Other causes.
Increase engine speed to 3600 rpm.
See Engine Operator’s Manual.
Add oil.
Low oil level.
Low engine oil pressure
(Indicated by oil light being on while
engine is running.)
Oil diluted or too light.
Change oil and check for source of
contamination.
Other causes.
See your dealer.
High engine oil consumption
Steering linkage is bent or needs
adjustment.
Adjust linkage. See “Steering Adjustments”
Mower is jerky when starting to
travel.
Drive belt is slipping.
Retention or replace drive belt.
Replace worn and damaged pulleys.
See your dealer.
Pulleys are worn or damage.
Transaxle is faulty.
Steering linkage is out of adjustment.
Adjust linkage. See “Steering Adjustments”
Steering levers do not return to
neutral.
Steering linkage is bent, broken, or
missing.
Replace steering linkage.
See item 1 on page 26.
Transaxle neutral return spring is broken Replace transaxle neutral return spring.
or missing.
Steering linkage is out of adjustment.
Adjust linkage See “Steering Adjustments”
Mower creeps when steering
control levers are in neutral.
Tires are not inflated properly.
Inflate tires to the correct tire pressure.
Mower circles or veers in one
direction.
Steering linkage is bent or needs
adjustment.
Adjust linkage See “Steering Adjustments”
Bypass assembly is sticking.
See your dealer.
Steering linkage is bent or needs
adjustment.
Repair or replace linkage.
Mower travels only in one direction
Transaxle is noisy
Drive belt is slipping.
Retention or replace drive belt.
Replace worn and damaged pulleys.
See your dealer.
Pulleys are worn or damage.
Transaxle is faulty.
Oil level in transaxle is low.
Oil is contaminated.
Fill transaxle to the correct level.
See your dealer.
Transaxle has some loose parts.
Bypass assembly is sticking.
Air is trapped in the hydraulic system.
See your dealer.
Purge transaxle of air or see your dealer.
Seals, housing, or gaskets are damaged. See your dealer.
Transaxle leaks oil
Air is trapped in hydraulic system.
Hydro-drive faulty.
Purge transaxle of air or see your dealer.
See your dealer.
Transaxles operates hot.
Not operating engine at rated speed.
Increase engine speed to 3600 rpm.
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 9: Torque & Tire Inflation Charts
Section 9: Torque & Tire Inflation Charts
Torque Values Chart
Bolt He a d Id e ntific a tion
Bolt He a d Id e ntific a tion
8.8
10.9
Class 10.9
5.8
Bolt Size
(Inc he s)
Bolt Size
(Me tric )
Class 5.8
Class 8.8
Grade 2
Grade 5
Grade 8
1
2
3
4
in-tpi
N m ft-lb
N·m ft-lb N·m ft-lb mm x pitch
N·m ft-lb N·m ft-lb N·m ft-lb
1/4" - 20
7.4
8.5
15
5.6
11
8
16
12
M 5 X 0.8
4
3
6
5
9
7
1/4" - 28
5/16" - 18
5/16" - 24
3/8" - 16
3/8" - 24
7/16" - 14
7/16" - 20
1/2" - 13
1/2" - 20
9/16" - 12
9/16" - 18
5/8" - 11
5/8" - 18
3/4" - 10
3/4" - 16
7/8" - 9
6
13
10
18
14
M 6 X 1
7
5
11
8
15
11
11
24
17
33
25
M 8 X 1.25
M 8 X 1
17
12
26
19
36
27
17
13
26
19
37
27
18
13
28
21
39
29
27
20
42
31
59
44
M10 X 1.5
M10 X 0.75
M12 X 1.75
M12 X 1.5
M12 X 1
33
24
52
39
72
53
31
22
47
35
67
49
39
29
61
45
85
62
43
32
67
49
95
70
58
42
91
67
125
130
145
200
l215
315
335
405
485
610
900
93
49
36
75
55
105
145
165
210
235
285
325
510
570
820
905
78
60
44
95
70
97
66
49
105
115
150
165
205
230
360
405
585
640
875
955
76
105
120
155
170
210
240
375
420
605
670
90
66
105
145
155
225
240
310
350
440
650
760
830
77
105
150
160
230
245
300
355
450
665
75
55
85
M14 X 2
92
68
105
115
165
180
230
260
325
480
560
610
95
70
110
120
150
170
265
295
430
475
645
705
M14 X 1.5
M16 X 2
99
73
105
130
150
235
260
225
250
340
370
480
540
680
750
890
79
145
155
195
220
280
310
480
525
960
105
115
145
165
205
230
355
390
705
97
M16 X 1.5
M18 X 2.5
M18 X 1.5
M20 X 2.5
M20 X 1.5
M24 X 3
110
170
190
165
185
250
275
355
395
500
555
655
7/8" - 14
1" - 8
1050 780
1150 845
1230 910
1350 995
1750 1290
1960 1440
M24 X 2
1" - 12
M30 X 3.5
M30 X 2
1510 1120 2100 1550
1680 1240 2320 1710
1-1/8" - 7
1 1/8" - 12
1 1/4" - 7
1 1/4" - 12
1 3/8" - 6
1 3/8" - 12
1 1/2" - 6
1 1/2" - 12
1080 795
1210 890
1060 785
M36 X 3.5
1730 1270 2650 1950 3660 2700
1880 1380 2960 2190 4100 3220
1520 1120 2460 1820
1680 1240 2730 2010
1990 1470 3230 2380
2270 1670 3680 2710
2640 1950 4290 3160
2970 2190 4820 3560
M36 X 2
1
in-tpi = nominal thread diameter in inches-threads per inch
N·m = newton-meters
2
3
4
1010 745
1180 870
1330 980
ft-lb= foot pounds
mm x pitch = nominal thread diameter in millimeters x thread
pitch
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.
Additional Torque Values
Drive Wheel Lug Nuts (1/2"-20 UNF)
75 ft-lbs.
102 N-m
Blade Spindle bolts (1/2"-20 UNF x 2 1/2" GR8)
Spindle Housing Flange Bolts
60 to 70 ft-lbs.
55 ft-lbs
82 to 95 N-m
75 N-m
Idler Pulley Bolts (5/8"-11 UNC GR5)
Electric Clutch Bolt (7/16"- 20 UNF GR8)
Hydro-Gear Top Port Plug (See Figure 5-8 on page 39, Item 4.)
Chock & Throttle Cable Clamp Screws
Transaxle Oil Filter Cap
130 ft-lbs.
176 N-m
50 to 55 ft-lbs.
15 ft-lbs.
68 to 75 N-m
20 N-m
35 in-lbs.
3.9 N-m
480-580 in-lbs.
54.23-65.53 N-m
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 9: Torque & Tire Inflation Charts
Tire Inflation Chart
Tire
Inflation PSI
Drive Wheels
Caster Wheels
8 to 12
8 to 12
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 10: Warranty
Section 10: Warranty
Warranty
Land Pride warrants to the original purchaser that this Land Pride product will be free from
defects in material and workmanship beginning on the date of purchase by the end user according
to the following schedule when used as intended and under normal service and conditions for
personal use.
Overall unit: 3 years limited warranty on Parts and Labor.
Kawasaki Engine: 3 years limited warranty through Engine manufacturer.
Transaxles: 3 years on Parts and Labor.
Evaporative Emission Control System: 2 years limited warranty from point of first retail sale.
Land Pride warrants to the original purchaser and any subsequent purchaser that this new non
road equipment, including its Evaporative Emission Control system, is designed, built, and
equipped so it conforms at the time of sale to the original purchaser with the requirements of Code
Of Federal Regulations title 40 part 1060, and is free from defects in materials and workmanship
Land Pride determines to be defective, will be repaired or replaced free of charge.
Blade Spindle bearings: 3 years Parts and Labor.
Front Caster Wheel Yoke Bearings: 3 years Parts and Labor
Battery: 1 year limited warranty.
Rental Units: Limited warranty on all materials and workmanship for a period of 90 days.
Belts, blades, and tires are considered wear items.
Filters and Plugs are considered maintenance items.
This Warranty is limited to the repair or replacement of any defective part by Land Pride and
the installation by the dealer of any such replacement part, and does not cover common wear
items such as blades, belts, tines, etc. Land Pride reserves the right to inspect any equipment or
parts which are claimed to have been defective in material or workmanship.
This Warranty does not apply to any part or product which in Land Pride’s judgment shall have
been misused or damaged by accident or lack of normal maintenance or care, or which has been
repaired or altered in a way which adversely affects its performance or reliability, or which has
been used for a purpose for which the product is not designed. Misuse also specifically includes
failure to properly maintain oil levels, grease points, and driveline shafts.
Claims under this Warranty must be made to the dealer which originally sold the product and
all warranty adjustments must be made through such dealer. Any action for breach of warranty
must be commenced within 37 months following delivery in non-rented application, and within 120
days following delivery in rented application.
This Warranty shall not be interpreted to render Land Pride liable for damages of any kind,
direct, consequential, or contingent to property. Furthermore, Land Pride shall not be liable for
damages resulting from any cause beyond its reasonable control. This Warranty does not extend
to loss of crops, any expense or loss for labor, supplies, rental machinery or for any other reason.
No other warranty of any kind whatsoever, express or implied, is made with respect to
this sale; and all implied warranties of merchantability and fitness for a particular purpose
which exceed the obligations set forth in this written warranty are hereby disclaimed and
excluded from this sale.
This Warranty is not valid unless registered with Land Pride within 30 days from the date of
purchase by the end user.
IMPORTANT: The Online Warranty Registration should be completed by the dealer at the time of
purchase. This information is necessary to provide you with quality customer service.
Model Number ____________________
Serial Number ____________________
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 10: Warranty
Evaporative Emission Control Components
Refer to Figure 10-1:
1. CAP,NON-VENTED FUEL
2. GAS TANK FITTING W/NUT&WASHER
3. CLAMP PINCH FOR .50 OD HOSE
4. CLAMP WRM DRV (.21-.63)
5. HFSS 3/8-16X5/8 GR5 YELLOW DIE
6. LH FUEL TANK, COMPLIANT
7. RH FUEL TANK, COMPLIANT
8. VALVE,FUEL SELECTOR
9. TEE 1/4HB POLYPROP
10. FUEL FILTER Z
11. HOSE RUBBER.25ID/.5 OD SAE30R7
12. HOSE RUBBER.25ID/.5 OD SAE30R7
13. HOSE RUBBER.25ID/.5 OD SAE30R7
14. HOSE RUBBER.25ID/.5 OD SAE30R7
15. HOSE RUBBER.25ID/.5 OD SAE30R7
16. HOSE RUBBER.25ID/.5 OD SAE30R7
17. GROMMET, FUEL TANK FITTING
18. ROV ASY
19. SV KIT, EPA VALVE & GROMMET
33823
Evaporative Emission Control Components
Figure 10-1
®
ZT60i & ZT72i (S/N 748110+) Accu-Z Zero Turn Mowers 357-552M
2/06/14
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|