Husqvarna Lawn Mower YTH2754XP User Manual
03002  
YTH2754XP  
Owner's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY RULES  
Safe Operation Practices for Ride-On Mowers  
GENERAL SERVICE  
III. CHILDREN  
•
Never operate machine in a closed area.  
Keep all nuts and bolts tight to be sure the equipment  
is in safe working condition.  
Never tamper with safety devices. Check their proper  
operation regularly.  
Keep machine free of grass, leaves, or other debris  
build-up. Cleanoilorfuelspillageandremoveanyfuel-  
soaked debris. Allow machine to cool before storing.  
If you strike a foreign object, stop and inspect the  
machine. Repair, if necessary, before restarting.  
Nevermakeanyadjustmentsorrepairswiththeengine  
running.  
Check grass catcher components and the discharge  
guard frequently and replace with manufacturer's rec-  
ommended parts, when necessary.  
Tragic accidents can occur if the operator is not alert to  
the presence of children. Children are often attracted to  
the machine and the mowing activity. Never assume that  
children will remain where you last saw them.  
•
•
•
•
•
•
•
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Never allow children to operate the machine.  
Useextracarewhenapproachingblindcorners,shrubs,  
trees, or other objects that may block your view of a  
child.  
•
•
•
•
•
•
Mower blades are sharp. Wrap the blade or wear  
gloves, and use extra caution when servicing them.  
Check brake operation frequently. Adjust and service  
as required.  
Maintain or replace safety and instruction labels, as  
necessary.  
•
•
IV. TOWING  
•
Tow only with a machine that has a hitch designed for  
towing. Do not attach towed equipment except at the  
hitch point.  
•
•
•
•
Follow the manufacturer's recommendation for weight  
limits for towed equipment and towing on slopes.  
Never allow children or others in or on towed equip-  
ment.  
On slopes, the weight of the towed equipment may  
cause loss of traction and loss of control.  
Travel slowly and allow extra distance to stop.  
•
Be sure the area is clear of bystanders before operat-  
ing. Stop machine if anyone enters the area.  
Never carry passengers.  
Do not mow in reverse unless absolutely necessary.  
Always look down and behind before and while back-  
ing.  
•
•
V. SERVICE  
SAFE HANDLING OF GASOLINE  
•
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Mow up and down slopes (15° Max), not across.  
Choose a low ground speed so that you will not have  
to stop or shift while on the slope.  
Avoid starting, stopping, or turning on a slope. If the  
tires lose traction, disengage the blades and proceed  
slowly straight down the slope.  
To avoid personal injury or property damage, use extreme  
careinhandlinggasoline. Gasolineisextremelyflammable  
and the vapors are explosive.  
•
Extinguish all cigarettes, cigars, pipes, and other  
sources of ignition.  
•
•
•
•
•
Use only approved gasoline container.  
Never remove gas cap or add fuel with the engine run-  
ning. Allow engine to cool before refueling.  
Never fuel the machine indoors.  
Never store the machine or fuel container where there  
is an open flame, spark, or pilot light such as on a water  
heater or other appliances.  
•
•
•
•
•
•
Never fill containers inside a vehicle or on a truck or  
trailer bed with plastic liner. Always place containers  
on the ground away from your vehicle when filling.  
Removegas-poweredequipmentfromthetruckortrailer  
and refuel it on the ground. If this is not possible, then  
refuel such equipment with a portable container, rather  
than from a gasoline dispenser nozzle.  
Keep the nozzle in contact with the rim of the fuel tank  
orcontaineropeningatalltimesuntilfuelingiscomplete.  
Do not use a nozzle lock-open device.  
•
•
•
If machine stops while going uphill, disengage blades,  
shift into reverse and back down slowly.  
Do not turn on slopes unless necessary, and then, turn  
slowly and gradually downhill, if possible.  
•
•
•
If fuel is spilled on clothing, change clothing immedi-  
ately.  
Never overfill fuel tank. Replace gas cap and tighten  
securely.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT SPECIFICATIONS  
CUSTOMER RESPONSIBILITIES  
•
•
Read and observe the safety rules.  
Gasoline Capacity  
and type:  
4 Gallons  
Unleaded Regular  
Follow a regular schedule in maintaining, caring for  
and using your tractor.  
Oil Type (API-SG-SL):  
SAE 10W30 (above 32°F)  
SAE 5W-30 (below 32°F)  
•
Followtheinstructionsunder“Maintenance”and“Stor-  
age” sections of this owner’s manual.  
Oil Capacity:  
W/ Filter:  
1.8 QT  
Spark Plug:  
(Gap: .030")  
Champion RC12YC  
WARNING: This tractor is equipped with an internal com-  
bustion engine and should not be used on or near any  
unimprovedforest-covered,brush-coveredorgrass-covered  
land unless the engine’s exhaust system is equipped with  
a spark arrester meeting applicable local or state laws (if  
any). If a spark arrester is used, it should be maintained  
in effective working order by the operator.  
Ground Speed (MPH):  
Forward:  
Reverse:  
0 – 5.8  
0 – 2.1  
Charging System:  
Battery:  
15 AMPS @ 3600 RPM  
AMP/HR:  
MIN. CCA:  
Case Size:  
35  
280  
U1R  
A spark arrester for the muffler is available through your  
nearestauthorizedservicecenter/department (SeeREPAIR  
PARTS section of this manual).  
Blade Bolt Torque:  
45-55FT. LBS.  
CONGRATULATIONS on your purchase of a new tractor.  
Ithasbeendesigned,engineeredandmanufacturedtogive  
you the best possible dependability and performance.  
Shouldyouexperienceanyproblemyoucannoteasilyrem-  
edy, please contact your nearest authorized servicecenter/  
department We have competent, well-trained technicians  
and the proper tools to service or repair this tractor.  
Please read and retain this manual. The instructions will  
enable you to assemble and maintain your tractor properly.  
Always observe the “SAFETY RULES”.  
TABLE OF CONTENTS  
SAFETY RULES .........................................................2-3  
PRODUCT SPECIFICATIONS....................................... 4  
CUSTOMER RESPONSIBILITIES................................. 4  
ASSEMBLY.................................................................6-9  
OPERATION ...........................................................10-16  
MAINTENANCE SCHEDULE ...................................... 17  
MAINTENANCE..................................................... 17-20  
SERVICE AND ADJUSTMENTS ............................21-25  
STORAGE.................................................................... 26  
TROUBLESHOOTING............................................27-28  
REPAIR PARTS ......................................................30-43  
WARRANTY................................................................. 44  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
UNASSEMBLED PARTS  
Mower  
Mower Front Wheel  
(5) Large Retainer  
Springs - 7/16  
(1) 3/4 O.D. Washers  
(1) Wheel  
(1) 1-1/4 O.D. Washer  
(2) Smaller Retainer  
Springs - 5/16  
(1) Locknut  
3/8-16  
(5) 1-3/16 O.D. Washers  
(1) Shoulder Bolt  
Battery  
(2) Rear Lift Link  
Assemblies  
(1) Anti-Sway Bar  
(2) Keps Nut 1/4-20  
(2) Hex Bolts 1/4-20 x 3/4  
(1) Front Link Assembly  
Slope Sheet  
Keys  
(1) Oil Drain Tube  
For Future Use  
(2) Keys  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping pur-  
poses.  
ADJUST SEAT (See Fig. 2)  
TOOLS REQUIRED FOR ASSEMBLY  
•
•
Sit in seat.  
A socket wrench set will make assembly easier. Standard  
wrench sizes are listed.  
Lift up adjustment lever (A) and slide seat until a com-  
fortable position is reached which allows you to press  
clutch/brake pedal all the way down.  
(1) 3/4" wrench  
(1) Utility knife  
(1) 9/16" wrench  
(2) 7/16" wrenches  
(1) Pliers  
•
Release lever to lock seat in position.  
(1) Tire Pressure Gauge  
When right or left hand is mentioned in this manual, it  
means from your point of view, when you are in the operat-  
ing position (seated behind the steering wheel).  
TO REMOVE TRACTOR FROM  
CARTON  
A
UNPACK CARTON  
•
Remove all accessible loose parts and parts cartons  
from carton .  
•
Cut along dashed lines on all four panels of carton.  
Remove end panels and lay side panels flat.  
•
•
Remove mower and packing materials.  
Check for any additional loose parts or cartons and  
remove.  
FIG. 2  
NOTE: You may now roll or drive your tractor off the skid.  
Follow the appropriate instruction below to remove the  
tractor from the skid.  
CONNECT BATTERY (See Figs. 1)  
WARNING:Beforestarting,read,understandandfollow  
all instructions in the Operation section of this manual. Be  
sure tractor is in a well-ventilated area. Be sure the area in  
front of tractor is clear of other people and objects.  
CAUTION: Do not short battery ter-  
minals by allowing a wrench or any  
other object to contact both terminals  
at the same time. Before connect-  
ing battery, remove metal bracelets,  
wristwatch bands, rings, etc.  
TO ROLL TRACTOR OFF SKID (See Op-  
eration section for location and function of  
controls)  
Positive terminal must be connected  
first to prevent sparking from acci-  
dental grounding.  
•
•
•
Raise attachment lift lever to its highest position.  
Release parking brake by depressing brake pedal.  
Place freewheel control in disengaged position to dis-  
engage transmission (See “TO TRANSPORT” in the  
Operation section of this manual).  
•
•
•
Lift hood to raised position.  
Remove terminal protective caps and discard.  
If this battery is put into service after month and year  
indicatedonlabel(L)(labellocatedbetweenterminals)  
charge battery for minimum of one hour at 6-10 amps.  
(See "BATTERY" in the Maintenance section of this  
manual for charging instructions).  
First connect RED battery cable to positive (+) terminal  
with hex bolt and keps nut as shown. Tighten securely.  
Slide terminal cover over terminal.  
•
Roll tractor forward off skid.  
TO DRIVE TRACTOR OFF SKID (See Op-  
eration section for location and function of  
controls)  
•
•
•
Be sure all the above assembly steps have been com-  
pleted.  
Check engine oil level and fill fuel tank with gasoline.  
Place freewheel control in "transmission engaged"  
position (see "TO TRANSPORT" in Operation section  
of this manual).  
•
•
Connect BLACK grounding cable to negative (-) ter-  
minal with remaining hex bolt and keps nut. Tighten  
securely.  
•
Sit on seat in operating position, depress brake pedal  
and set the parking brake.  
L
•
•
Raise attachment lift lever to its highest position.  
Remove key from bag and start the engine (see "TO  
START" in the Operation section of this manual). After  
engine has started, move throttle control to idle (slow)  
position.  
02954  
•
Release parking brake.  
FIG. 1  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
•
Slowly depress forward drive pedal and drive tractor  
off skid.  
•
•
Apply brake to stop tractor and set parking brake.  
Turn ignition key to "STOP" position.  
Continue with the instructions that follow.  
ASSEMBLE FRONT WHEEL TO  
MOWER (See Fig. 3)  
•
Using shoulder bolt, washer and locknut from parts  
bag,assemblefrontwheeltomowerasshown.Tighten  
securely.  
A
FIG. 5  
NOTE: Be sure mower side suspension arms (A) are point-  
ing forward before sliding mower under tractor.  
•
•
Slide mower under tractor until it is centered under  
tractor.  
FIRST INSTALL ANTI-SWAY BAR (S).  
- From right side of mower, insert anti-sway bar into  
hole in transmission bracket (T).  
FIG. 3  
T
INSTALL MOWER AND DRIVE BELT  
S
(See Figs. 4-12)  
See MOWER AND DRIVE BELT ASSEMBLY Supplement  
Sheet for additional guidance on this assembly.  
Be sure tractor is on level surface and engage parking  
brake.  
•
Lower attachment lift lever to it's lowest position.  
CAUTION:Liftleverisspringloaded.Have  
a tight grip on lift lever, lower it slowly and  
engage in lowest position.  
A
02995  
•
Turn steering wheel to the left as far as it will go and  
position mower on right side of tractor with deflector  
shield to the right.  
FIG. 6  
- Pivot bar towards you and insert other end of bar  
into hole in rear mower bracket (D). Move mower as  
needed to insert bar.  
- Secure with washer and retainer spring as shown  
using small 5/16 retainer spring.  
D
02965  
FIG. 4  
•
Remove plastic tie securing belt, bring belt forward  
and check belt for proper routing in all mower pulley  
grooves.  
02996  
FIG. 7  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
•
•
ATTACH MOWER SIDE SUSPENSIONARMS (A) TO  
•
Turn steering wheel to position wheels straight for-  
CHASSIS - Position hole in arm over pin (B) on outside  
of tractor chassis and secure with washer and retainer  
spring.  
ward.  
•
ATTACH FRONT LINK (E) - Work from left side of  
tractor. Insert rod end of link assembly through front  
hole in tractor front suspension bracket (F) and secure  
with7/16 retainer spring (G) through hole in link located  
behind the bracket.  
Repeat on opposite side of tractor.  
•
Insert other end of link (E) into hole in front mower  
bracket (H) and secure with washer and 5/16 retainer  
spring (J).  
A
5/16  
H
E
J
B
FIG. 8  
F
G
•
•
ATTACH REAR LIFT LINKS (C) - Insert rod end of link  
assembly into hole in tractor lift shaft suspension arm  
(L) and pivot link down to mower. Lift rear corner of  
mower and position slot in link assembly over pin on  
rear mower bracket (D) and secure with washer and  
retainer spring.  
7/16  
FIG. 10  
•
•
Disengage belt tension rod (K) from locking bracket  
(L).  
Install belt onto engine clutch pulley (M).  
Repeat on opposite side of tractor.  
IMPORTANT: Check belt for proper routing in all mower  
pulley grooves.  
L
C
D
FIG. 9  
L
B
M
K
F
A
E
H
S
C
D
FIG. 11  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
✓CHECKLIST  
M
BEFORE YOU OPERATE YOUR NEW TRACTOR, WE  
WISHTO ASSURETHATYOU RECEIVETHE BEST PER-  
FORMANCE AND SATISFACTION FROMTHIS QUALITY  
PRODUCT.  
PLEASE REVIEW THE FOLLOWING CHECKLIST:  
✓
All assembly instructions have been completed.  
✓
✓
✓
✓
No remaining loose parts in carton.  
Battery is properly prepared and charged.  
Seat is adjusted comfortably and tightened securely.  
All tires are properly inflated. (For shipping purposes,  
the tires were overinflated at the factory).  
FIG. 12  
•
Engage belt tension rod (K) on locking bracket (L).  
✓
Be sure mower deck is properly leveled side-to-side/  
front-to-rear for best cutting results. (Tires must be  
properly inflated for leveling).  
Check mower and drive belts. Be sure they are routed  
properly around pulleys and inside all belt keepers.  
Check wiring. See that all connections are still secure  
and wires are properly clamped.  
Before driving tractor, be sure freewheel control is in  
“transmission engaged” position (see “TO TRANS-  
PORT” in the Operation section of this manual).  
CAUTION: Belt tension rod is spring  
loaded. Have a tight grip on rod and en-  
gage slowly.  
✓
✓
✓
•
•
Raise attachment lift lever to highest position.  
If necessary, adjust gauge wheels before operating  
mower as shown in the Operation section of this  
manual.  
WHILE LEARNING HOW TO USEYOUR TRACTOR, PAY  
EXTRAATTENTION TO THE FOLLOWING IMPORTANT  
ITEMS:  
CHECK TIRE PRESSURE  
The tires on your tractor were overinflated at the factory  
for shipping purposes. Correct tire pressure is important  
for best cutting performance.  
✓
Engine oil is at proper level.  
✓
Fuel tank is filled with fresh, clean, regular unleaded  
gasoline.  
•
Reduce tire pressure to PSI shown on tires.  
✓
Become familiar with all controls, their location and  
function. Operate them before you start the engine.  
CHECK DECK LEVELNESS  
For best cutting results, mower housing should be properly  
leveled. See“TOLEVELMOWERHOUSING”intheService  
and Adjustments section of this manual.  
✓
✓
Be sure brake system is in safe operating condition.  
Be sure Operator Presence System and Reverse Op-  
eration System (ROS) are working properly (See the  
Operation and Maintenance sections in this manual).  
✓
It is important to purge the transmission before oper-  
ating your tractor for the first time. Follow proper start-  
ing and transmission purging instructions (See “TO  
START ENGINE” and “PURGE TRANSMISSION” in  
the Operation section of this manual).  
CHECK FOR PROPER POSITION OF ALL  
BELTS  
See the figures that are shown for replacing motion and  
mower blade drive belts in the Service and Adjustments  
section of this manual. Verify that the belts are routed  
correctly.  
CHECK BRAKE SYSTEM  
Afteryoulearnhowtooperateyourtractor,checktoseethat  
the brake is operating properly. See “TO CHECK BRAKE”  
in the Service and Adjustments section of this manual.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean-  
ing.  
FAST  
SLOW  
REVERSE  
HIGH  
LOW  
NEUTRAL  
CHOKE  
IGNITION SWITCH  
MOWER LIFT  
ENGINE START  
MOWER HEIGHT  
ENGINE ON  
PARKING BRAKE  
REVERSE  
OPERATION  
SYSTEM (ROS)  
ENGINE OFF  
CLUTCH/BRAKE  
PEDAL  
LIGHTS ON  
CRUISE CONTROL  
BATTERY  
REVERSE  
FUEL  
FORWARD  
15  
15  
ATTACHMENT  
CLUTCH ENGAGED  
DANGER, KEEP HANDS  
AND FEET AWAY  
ATTACHMENT  
CLUTCH DISENGAGED  
SLOPE HAZARDS  
KEEP AREA CLEAR  
(SEE SAFETY RULES SECTION)  
DANGER indicates a hazard which, if not avoided,  
will result in death or serious injury.  
WARNING indicates a hazard which, if not avoided,  
could result in death or serious injury.  
FREE WHEEL  
(Automatic Models only)  
CAUTION indicates a hazard which, if not avoided,  
might result in minor or moderate injury.  
CAUTION when used without the alert symbol,  
indicates a situation that could result in damage  
to the tractor and/or engine.  
Failure to follow instructions  
could result in serious injury or  
death. The safety alert symbol  
is used to identify safety inform-  
ation about hazards which can  
result in death, serious injury  
and/or property damage.  
HOT SURFACES indicates a hazard which,  
if not avoided, could result in death, serious injury  
and/or property damage.  
FIRE indicates a hazard which, if not avoided,  
could result in death, serious injury and/or  
property damage.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOW YOUR TRACTOR  
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR  
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.  
Save this manual for future reference.  
P
H
D
E
G
K
L
N
B
F
J
C
A
M
FIG. 13  
Our tractors conform to the applicable safety standards of the American National Standards Institute.  
(A) ATTACHMENT LIFT LEVER – Used to raise and lower the  
mower or other attachments mounted to your tractor.  
(B) BRAKE PEDAL – Used for braking the tractor and starting  
the engine.  
(H) LIGHT SWITCH – Turns the headlights on and off.  
(J) CRUISE CONTROL LEVER – Used to set forward  
movement of tractor at desired speed without holding the  
forward drive pedal.  
(C) PARKING BRAKE – Locks clutch/brake pedal into the  
brake position.  
(K) FORWARD DRIVE PEDAL – Used for forward movement  
of tractor.  
(D) THROTTLE CONTROL – Used to control engine speed.  
(E) ATTACHMENT CLUTCH SWITCH – Used to engage the  
mower blades, or other attachments mounted to your tractor.  
(F) IGNITION SWITCH – Used for starting and stopping the  
engine.  
(G) REVERSE OPERATION SYSTEM (ROS) "ON" POSITION  
– Allows operation of mower or other powered attachment  
while in reverse.  
(L) REVERSE DRIVE PEDAL – Used for reverse movement of  
tractor.  
(M) FREEWHEEL CONTROL – Disengages transmission for  
pushing or slowly towing the tractor with the engine off.  
(N) CHOKE CONTROL – Used when starting a cold engine.  
(P) SERVICE REMINDER / HOUR METER – Indicates when  
service is required for the engine and mower.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The operation of any tractor can result in foreign objects thrown into the eyes, which can result  
in severe eye damage. Always wear safety glasses or eye shields while operating your tractor  
or performing any adjustments or repairs. We recommend standard safety glasses or a wide  
vision safety mask worn over spectacles.  
IMPORTANT: Leaving the ignition switch in any position  
HOW TO USE YOUR TRACTOR  
other than "STOP" will cause the battery to discharge and  
go dead.  
TO SET PARKING BRAKE(See Fig. 14)  
NOTE: Under certain conditions when tractor is standing  
idlewiththeenginerunning, hotengineexhaustgasesmay  
cause “browning” of grass. To eliminate this possibility, al-  
ways stop engine when stopping tractor on grass areas.  
Your tractor is equipped with an operator presence sens-  
ing switch. When engine is running, any attempt by the  
operator to leave the seat without first setting the parking  
brake will shut off the engine.  
•
•
Depress brake pedal (B) all the way down and hold.  
CAUTION: Always stop tractor com-  
pletely, as described above, before  
leaving the operator's position.  
Pull parking brake lever (C) up and hold, release pres-  
sure from brake pedal (B), then release parking brake  
lever. Pedal should remain in brake position. Make  
sure parking brake will hold tractor secure.  
D
B
N
F
C
FIG. 14  
FIG. 16  
STOPPING  
MOWER BLADES  
TO USE THROTTLE CONTROL -D(See Fig.  
16)  
•
To stop mower blades, push attachment clutch switch in  
to disengaged position (o).  
Always operate engine at full speed (fast).  
•
•
Operating engine at less than full speed (fast) reduces  
engines operating efficiency.  
Full speed (fast) offers the best bagging and mower  
performance.  
TO USE CHOKE CONTROL -N (See Fig. 16)  
Usechokecontrolwheneveryouarestartingacoldengine.  
Do not use to start a warm engine.  
(l) ATTACHMENT  
(o) PUSH-IN TO  
CLUTCH SWITCH  
“DISENGAGED”  
PULL OUT TO “ENGAGE”  
•
To engage choke control, pull knob out. Slowly push  
knob in to disengage.  
FIG. 15  
GROUND DRIVE -  
TO MOVE FORWARD AND BACKWARD  
(See Fig. 17)  
The direction and speed of movement is controlled by the  
forward and reverse drive pedals.  
•
To stop ground drive, depress brake pedal all the way  
down.  
ENGINE -  
Move throttle control (D) between half and full speed  
(fast) position.  
•
•
•
Start tractor and release parking brake.  
Slowlydepressforward(K)orreverse(L)drivepedalto  
begin movement. Ground speed increases the further  
down the pedal is depressed.  
NOTE: Failure to move throttle control between half and  
full speed (fast) position, before stopping, may cause en-  
gine to “backfire”.  
•
Turn ignition key (F) to “STOP” position and remove  
key. Alwaysremovekeywhenleavingtractortoprevent  
unauthorized use.  
•
Never use choke (N) to stop engine.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
•
Theaveragelawnshouldbecuttoapproximately2-1/2  
inches during the cool season and to over 3 inches  
during hot months. For healthier and better looking  
lawns, mow often and after moderate growth.  
•
For best cutting performance, grass over 6 inches  
in height should be mowed twice. Make the first cut  
relatively high; the second to desired height.  
J
TO ADJUST GAUGE WHEELS (See Fig. 19)  
Gaugewheels areproperlyadjustedwhentheyareslightly  
off the ground when mower is at the desired cutting height  
in operating position. Gauge wheels then keep the deck  
in proper position to help prevent scalping in most terrain  
conditions.  
K
L
FIG. 17  
NOTE: Adjust gauge wheels with tractor on a flat level  
surface.  
TO USE CRUISE CONTROL -J (See Fig. 17)  
The cruise control feature can be used for forward travel  
only.  
•
Adjust mower to desired cutting height (See “TO AD-  
JUST MOWER CUTTING HEIGHT” in this section of  
manual).  
SYSTEM CHARACTERISTICS  
•
With mower in desired height of cut position, gauge  
wheels should be assembled so they are slightly off  
the ground. Install gauge wheel in appropriate hole.  
Tighten securely.  
The cruise control should only be used while mowing or  
transporting on relatively smooth, straight surfaces. Other  
conditions such as trimming at slow speeds may cause the  
cruise control to disengage. Do not use the cruise control  
on slopes, rough terrian or while trimmimg or turning.  
•
Repeat for all, installing gauge wheel in same adjust-  
ment hole.  
•
With forward drive pedal depressed to desired speed,  
pull cruise control lever (J) up and hold while lifting  
your foot off the pedal, then release the lever.  
To disengage the cruise control, depress the brake pedal  
or tap on forward drive pedal.  
TO ADJUST MOWER CUTTING HEIGHT  
(See Fig. 18)  
The position of the attachment lift lever (A) determines the  
cutting height.  
FIG.19  
A
TO OPERATE MOWER  
Yourtractorisequippedwithanoperatorpresencesensing  
switch. Any attempt by the operator to leave the seat with  
the engine running and the attachment clutch engaged  
will shut off the engine. You must remain fully and centrally  
positioned in the seat to prevent the engine from hesitating  
or cutting off when operating your equipment on rough,  
rolling terrain or hills.  
FIG. 18  
1. Select desired height of cut with attachment lift lever.  
2. Start mower blades by engaging attachment clutch  
control.  
•
Put attachment lift lever in desired cutting height slot.  
The cutting height range is approximately 1" to 4". The  
heights are measured from the ground to the blade tip with  
theenginenotrunning. Theseheightsareapproximateand  
may vary depending upon soil conditions, height of grass  
and types of grass being mowed.  
TO STOP MOWER BLADES -  
disengage attachment clutch control.  
CAUTION: Do not operate the mower  
without either the entire grass catcher,  
onmowerssoequipped,orthedeflector  
shield (S) in place.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
•
•
•
Torestartmovement, slowlyreleaseparkingbrakeand  
brake pedal.  
Slowly depress appropriate drive pedal to slowest set-  
ting.  
Make all turns slowly.  
S
TO TRANSPORT (See Figs. 13 and 21)  
When pushing or towing your tractor, be sure to disengage  
transmission by placing freewheel control in freewheeling  
position. Free wheel control is located at the rear drawbar  
of tractor.  
FIG. 20  
•
•
•
•
Raiseattachmentlifttohighestpositionwithattachment  
lift control.  
Pull freewheel control out and down into the slot and  
release so it is held in the disengaged position.  
Do not push or tow tractor at more than two (2)  
MPH.  
To reengage transmission, reverse above procedure.  
REVERSE OPERATION SYSTEM (ROS)  
Your tractor is equipped with a Reverse Operation System  
(ROS). Any attempt by the operator to travel in the reverse  
direction with the attachment clutch engaged will shut off  
the engine unless ignition key is placed in the ROS "ON"  
position.  
NOTE: To protect hood from damage when transporting  
your tractor on a truck or a trailer, be sure hood is closed  
and secured to tractor. Use an appropriate means of tying  
hood to tractor (rope, cord, etc.).  
WARNING: Backing up with the attachment clutch en-  
gaged while mowing is strongly discouraged. Turning the  
ROS "ON", to allow reverse operation with the attachment  
clutch engaged, should only be done when the operator  
decides it is necessary to reposition the machine with the  
attachment engaged. Do not mow in reverse unless  
absolutely necessary.  
Transmission Engaged  
USING THE REVERSE OPERATION SYSTEM -  
Only use if you are certain no children or other bystanders  
will enter the mowing area.  
•
•
Depress brake pedal all the way down.  
Withenginerunning,turnignitionkeycounterclockwise  
to ROS "ON" position.  
•
•
Look down and behind before and while backing.  
Slowly depress reverse drive pedal to start move-  
ment.  
When use of the ROS is no longer needed, turn the  
ignition key clockwise to engine "ON" position.  
Transmission Disengaged  
FIG. 21  
•
SERVICE REMINDER/HOUR METER  
Service reminder shows the total number of hours the  
engine has run and flashes to indicate that the engine  
or mower needs servicing. When service is required, the  
service reminder will flash for two hours. To service engine  
and mower, see the Maintenance section of this manual.  
ROS "ON" POSITION  
ENGINE "ON" POSITION  
(NORMAL OPERATING)  
NOTE: Service reminder runs when the ignition key is in  
any position but "STOP". For accurate reading, be sure  
key remains in the "STOP" position when engine is not  
running.  
TOWING CARTS AND OTHER ATTACHMENTS  
Tow only the attachments that are recommended by and  
complywithspecificationsofthemanufacturerofyourtrac-  
tor. Use common sense when towing. Too heavy of a load,  
while on a slope, is dangerous. Tires can lose traction with  
the ground and cause you to lose control of your tractor.  
TO OPERATE ON HILLS  
CAUTION: Donotdriveupordownhills  
with slopes greater than 15° and do not  
drive across any slope.  
•
Choose the slowest speed before starting up or down  
hills.  
•
•
Avoid stopping or changing speed on hills.  
If stopping is absolutely necessary, push brake pedal  
quickly to brake position and engage parking brake.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
•
Insertkeyintoignitionandturnkeyclockwiseto“START”  
BEFORE STARTING THE ENGINE  
positionandreleasekeyassoonasenginestarts.Donot  
run starter continuously for more than fifteen seconds  
per minute. If the engine does not start after several  
attempts, pushchokecontrolin, waitafewminutesand  
try again. If engine still does not start, pull the choke  
control out and retry.  
CHECK ENGINE OIL LEVEL  
The engine in your tractor has been shipped, from the  
factory, already filled with summer weight oil.  
•
•
Check engine oil with tractor on level ground.  
Unthread and remove oil fill cap/dipstick; wipe oil off.  
Reinsert the dipstick into the tube and rest oil fill cap on  
the tube. Do not thread the cap onto the tube. Remove  
and read oil level. If necessary, add oil until “FULL”  
mark on dipstick is reached. Do not overfill.  
WARM WEATHER STARTING (50° F and above)  
•
When engine starts, slowly push choke control in until  
the engine begins to run smoothly. If the engine starts  
to run roughly, pull the choke control out slightly for a  
few seconds and then continue to push the control in  
slowly.  
The attachments and ground drive can now be used. If  
the engine does not accept the load, restart the engine  
and allow it to warm up for one minute using the choke  
as described above.  
•
•
For cold weather operation you should change oil for  
easier starting (See “OIL VISCOSITY CHART” in the  
Maintenance section of this manual).  
To change engine oil, see the Maintenance section in  
this manual.  
•
ADD GASOLINE  
COLD WEATHER STARTING (50° F and below)  
•
Fill fuel tank to bottom of filler neck. Do not overfill. Use  
fresh,clean,regularunleadedgasolinewithaminimumof  
87 octane. (Use of leaded gasoline will increase carbon  
and lead oxide deposits and reduce valve life). Do not  
mix oil with gasoline. Purchase fuel in quantities that can  
be used within 30 days to assure fuel freshness.  
•
When engine starts, slowly push choke control in until  
the engine begins to run smoothly. Continue to push  
the choke control in small steps allowing the engine to  
acceptsmallchangesinspeedandload,untilthechoke  
control is fully in. If the engine starts to run roughly, pull  
thechokecontroloutslightlyforafewsecondsandthen  
continue to push the control in slowly. This may require  
an engine warm-up period from several seconds to  
several minutes, depending on the temperature.  
CAUTION: Wipe off any spilled oil or  
fuel. Do not store, spill or use gasoline  
near an open flame.  
AUTOMATIC TRANSMISSION WARM UP  
•
Beforedrivingtheunitincoldweather,thetransmission  
should be warmed up as follows:  
IMPORTANT: WHEN OPERATING IN TEMPERATURES  
BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE  
GASOLINE TO HELP INSURE GOOD COLD WEATHER  
STARTING.  
•
•
Be sure the tractor is on level ground.  
Release the parking brake and let the brake slowly  
return to operating position.  
CAUTION: Alcohol blended fuels (called gasohol or  
usingethanolormethanol)canattractmoisturewhich  
leads to separation and formation of acids during  
storage. Acidic gas can damage the fuel system of  
anenginewhileinstorage. Toavoidengineproblems,  
the fuel system should be emptied before storage  
of 30 days or longer. Drain the gas tank, start the  
engineandletitrununtilthefuellinesandcarburetor  
are empty. Use fresh fuel next season. See Storage  
Instructions for additional information. Never use  
engine or carburetor cleaner products in the fuel  
tank or permanent damage may occur.  
•
Allowoneminutefortransmissiontowarmup. This  
can be done during the engine warm up period.  
•
Theattachmentscanbeusedduringtheenginewarm-up  
period after the transmission has been warmed up and  
may require the choke control be pulled out slightly.  
NOTE: If at a high altitude (above 3000 feet) or in cold  
temperatures (below 32 F) the carburetor fuel mixture may  
need to be adjusted for best engine performance. See “TO  
ADJUST CARBURETOR” in the Service and Adjustments  
section of this manual.  
PURGE TRANSMISSION  
TO START ENGINE (See Fig. 13)  
When starting the engine for the first time or if the engine  
has run out of fuel, it will take extra cranking time to move  
fuel from the tank to the engine.  
CAUTION: Never engage or disengage  
freewheel lever while the engine is run-  
ning.  
•
Besurefreewheelcontrolisinthetransmissionengaged  
position.  
To ensure proper operation and performance, it is recom-  
mended that the transmission be purged before operating  
tractor for the first time. This procedure will remove any  
trapped air inside the transmission which may have de-  
veloped during shipping of your tractor.  
IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE  
REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD  
BE PURGEDAFTER REINSTALLATION BEFORE OPERATING  
THE TRACTOR.  
•
Sit on seat in operating position, depress brake pedal  
and set parking brake.  
Move attachment clutch to “DISENGAGED” position.  
Move throttle control to fast position  
Pull choke control out for a cold engine start attempt.  
For a warm engine start attempt the choke control may  
not be needed.  
•
•
•
NOTE: Before starting, read the warm and cold starting  
procedures below.  
•
Place tractor safely on level surface with engine off and  
parking brake set.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
•
•
•
Disengage transmission by placing freewheel control  
infreewheelingposition(See“TOTRANSPORT”inthis  
section of manual).  
Sitting in the tractor seat, start engine. After the en-  
gine is running, move throttle control to slow position.  
Disengage parking brake  
Depress forward drive pedal to full forward position,  
hold for five (5) seconds and release pedal. Depress  
reverse drive pedal to full reverse position, hold for five  
(5) seconds and release pedal. Repeat this procedure  
three (3) times.  
FIG. 22  
NOTE: During this procedure there will be no movement  
of drive wheels. The air is being removed from hydraulic  
drive system.  
•
If grass is extremely tall, it should be mowed twice to  
reduce load and possible fire hazard from dried clip-  
pings. Make first cut relatively high; the second to the  
desired height.  
Do not mow grass when it is wet. Wet grass will plug  
mower and leave undesirable clumps. Allow grass to  
dry before mowing.  
Always operate engine at full throttle when mow-  
ing to assure better mowing performance and proper  
discharge of material. Regulate ground speed by se-  
lecting a low enough gear to give the mower cutting  
performance as well as the quality of cut desired.  
When operating attachments, select a ground speed  
that will suit the terrain and give best performance of  
the attachment being used.  
•
•
Shut- off engine and set parking brake.  
Engage transmission by placing freewheel control in  
engaged position (See “TO TRANSPORT” in this sec-  
tion of manual).  
•
•
•
•
Sitting in the tractor seat, start engine.After the engine  
is running, move throttle control to half (1/2) speed.  
Disengage parking brake.  
Drive tractor forward for approximately five feet then  
backwards for five feet. Repeat this driving procedure  
three times.  
•
Your transmission is now purged and now ready for normal  
operation.  
MOWING TIPS  
•
Mowershouldbeproperlyleveledforbestmowingper-  
formance. See“TOLEVELMOWERHOUSING”inthe  
Service and Adjustments section of this manual.  
•
•
The left hand side of mower should be used for trim-  
ming.  
Drive so that clippings are discharged onto the area  
that has been cut. Have the cut area to the right of the  
machine. This will result in a more even distribution of  
clippings and more uniform cutting.  
Whenmowinglargeareas,startbyturningtotherightso  
that clippings will discharge away from shrubs, fences,  
driveways, etc. After one or two rounds, mow in the  
opposite direction making left hand turns until finished  
(See Fig. 22).  
•
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
BEFORE  
EACH  
USE  
EVERY  
8
HOURS  
EVERY  
25  
HOURS  
EVERY  
50  
HOURS  
EVERY  
100  
HOURS  
EVERY  
SEASON  
BEFORE  
STORAGE  
MAINTENANCE  
SCHEDULE  
Check Brake Operation  
T Check Tire Pressure  
R Check Operator Presence & ROS Systems  
A Check for Loose Fasteners  
Check/Replace Mower Blades  
3
4
C
T
0
Lubrication Chart  
Check Battery Level  
Clean Battery and Terminals  
Check Transaxle Cooling  
Check Mower Levelness  
Check V-Belts  
R
Check Engine Oil Level  
1,2  
Change Engine Oil (with oil filter)  
1,2  
E Change Engine Oil (without oil filter)  
N Clean Air Filter  
2
2
G Clean Air Screen  
Inspect Muffler/Spark Arrester  
I
N
1,  
2
2
Replace Oil Filter (If equipped)  
E Clean Engine Cooling Fins  
Replace Spark Plug  
Replace Air Filter Paper Cartridge  
Replace Fuel Filter  
2
1 - Change more often when operating under a heavy load or  
in high ambient temperatures.  
3 - Replace blades more often when mowing in sandy soil.  
4 - Not required if equipped with maintenance-free battery.  
2 - Service more often when operating in dirty or dusty conditions.  
LUBRICATION CHART  
GENERAL RECOMMENDATIONS  
➀ SPINDLE ZERK  
➀ SPINDLE ZERK  
The warranty on this tractor does not cover items that have  
beensubjectedtooperatorabuseornegligence. Toreceive  
full value from the warranty, operator must maintain tractor  
as instructed in this manual.  
➀ FRONT  
WHEEL  
➀ FRONT  
WHEEL  
BEARING  
ZERK  
BEARING  
ZERK  
Some adjustments will need to be made periodically to  
properly maintain your tractor.  
➁ ENGINE  
At least once a season, check to see if you should make  
any of the adjustments described in the Service and  
Adjustments section of this manual.  
• At least once a year you should replace the spark plug,  
clean or replace air filter, and check blades and belts  
for wear. A new spark plug and clean air filter assure  
proper air-fuel mixture and help your engine run better  
and last longer.  
➀ STEERING  
SECTOR GEAR  
TETH  
➀ MANDREL  
ZERKS  
02956  
BEFORE EACH USE  
➀ General Purpose Grease  
•
•
•
•
Check engine oil level.  
➁ Refer to Maintenance “ENGINE” Section  
Check brake operation.  
Check tire pressure.  
Check operator presence and  
ROS systems for proper operation.  
Check for loose fasteners.  
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS  
WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS  
LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL  
SHORTENTHELIFEOFTHESELF-LUBRICATINGBEARINGS.  
IFYOUFEELTHEYMUSTBELUBRICATED,USEONLYADRY,  
POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY.  
•
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
BLADE CARE  
For best results mower blades must be sharp. Replace  
worn, bent or damaged blades.  
TRACTOR  
Always observe safety rules when performing any main-  
tenance.  
CAUTION: Use only a replacement  
blade approved by the manufacturer of  
your tractor. Using a blade not approved  
by the manufacturer of your tractor is haz-  
ardous,coulddamageyourtractorandvoid  
your warranty.  
BRAKE OPERATION  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be serviced. (See “TO CHECK  
BRAKE” in the Service and Adjustments section of this  
manual).  
BLADE REMOVAL (See Fig. 23)  
TIRES  
•
Raise mower to highest position to allow access to  
blades.  
•
•
•
Maintain proper air pressure in all tires (See PSI on  
tires).  
NOTE: Protect your hands with gloves and/or wrap blade  
with heavy cloth.  
Keep tires free of gasoline, oil, or insect control chemi-  
cals which can harm rubber.  
Avoid stumps, stones, deep ruts, sharp objects and  
other hazards that may cause tire damage.  
•
•
Remove blade bolt by turning counterclockwise.  
Install new blade with stamped "GRASS SIDE" facing  
the ground.  
NOTE: To seal tire punctures and prevent flat tires due to  
slow leaks, tire sealant may be purchased from your local  
parts dealer. Tire sealant also prevents tire dry rot and  
corrosion.  
IMPORTANT: To ensure proper assembly, center hole in  
blade must align with star on mandrel assembly.  
•
Install and tighten blade bolt securely (45-55 Ft. Lbs.  
torque).  
OPERATOR PRESENCE SYSTEM AND REVERSE OP-  
ERATION SYSTEM (ROS)  
IMPORTANT: Special blade bolt is heat treated.  
Be sure operator presence and reverse operation systems  
are working properly. If your tractor does not function as  
described, repair the problem immediately.  
MANDREL  
ASSEMBLY  
BLADE  
CENTER  
HOLE  
•
The engine should not start unless the brake pedal is  
fully depressed, and the attachment clutch control is  
in the disengaged position.  
BLADE BOLT  
(SPECIAL)  
CHECK OPERATOR PRESENCE SYSTEM  
025  
44  
•
•
•
Whentheengineisrunning,anyattemptbytheoperator  
to leave the seat without first setting the parking brake  
should shut off the engine.  
When the engine is running and the attachment clutch  
is engaged, any attempt by the operator to leave the  
seat should shut off the engine.  
STAR  
FIG. 23  
The attachment clutch should never operate unless  
the operator is in the seat.  
BATTERY  
Yourtractorhasabatterychargingsystemwhichissufficient  
for normal use. However, periodic charging of the battery  
with an automotive charger will extend its life.  
Engine "ON" Position  
ROS "ON" Position  
(Normal Operating)  
•
•
•
•
Keep battery and terminals clean.  
Keep battery bolts tight.  
Keep small vent holes open.  
Recharge at 6-10 amperes for 1 hour.  
NOTE: The original equipment battery on your tractor is  
maintenance free. Do not attempt to open or remove caps  
or covers. Adding or checking level of electrolyte is not  
necessary.  
CHECK REVERSE OPERATION (ROS) SYSTEM  
•
When the engine is running with the ignition switch in  
the engine "ON" position and the attachment clutch  
engaged, any attempt by the operator to shift into  
reverse should shut off the engine.  
TO CLEAN BATTERY AND TERMINALS  
Corrosion and dirt on the battery and terminals can cause  
the battery to “leak” power.  
•
When the engine is running with the ignition switch in  
the ROS "ON" position and the attachment clutch en-  
gaged, any attempt by the operator to shift into reverse  
should NOT shut off the engine.  
•
•
Remove terminal guard.  
Disconnect BLACK battery cable first then RED bat-  
tery cable and remove battery from tractor.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
TO CHANGE ENGINE OIL (See Figs. 24 and 25)  
•
•
Rinse the battery with plain water and dry.  
Clean terminals and battery cable ends with wire brush  
until bright.  
Determine temperature range expected before oil change.  
All oil must meet API service classification SG-SL.  
•
•
Coat terminals with grease or petroleum jelly.  
•
•
•
•
Be sure tractor is on level surface.  
Oil will drain more freely when warm.  
Catch oil in a suitable container.  
Remove oil fill cap/dipstick. Be careful not to allow dirt  
to enter the engine when changing oil.  
Remove yellow cap from end of drain valve and install  
the drain tube onto the fitting.  
Unlock drain valve by pushing inward and turning  
counterclockwise.  
Reinstall battery (See “REPLACING BATTERY" in  
the SERVICE AND ADJUSTMENTS section of this  
manual).  
V-BELTS  
•
•
Check V-belts for deterioration and wear after 100 hours  
of operation and replace if necessary. The belts are not  
adjustable. Replace belts if they begin to slip from wear.  
TRANSAXLE COOLING  
The transmission fan and cooling fins should be kept clean  
to assure proper cooling.  
OIL DRAIN VALVE  
Do not attempt to clean fan or transmission while engine  
is running or while the transmission is hot. To prevent pos-  
sible damage to seals, do not use high pressure water or  
steam to clean transaxle.  
CLOSED  
AND  
LOCKED  
POSITION  
•
Inspect cooling fan to be sure fan blades are intact and  
clean.  
•
Inspect cooling fins for dirt, grass clippings and other  
materials. To prevent damage to seals, do not use  
compressed air or high pressure sprayer to clean cool-  
ing fins.  
YELLOW  
CAP  
TRANSAXLE PUMP FLUID  
The transaxle was sealed at the factory and fluid mainte-  
nance is not required for the life of the transaxle. Should  
the transaxle ever leak or require servicing, contact your  
nearest authorized service center/department.  
FIG. 25  
•
•
To open, pull out on the drain valve.  
After oil has drained completely, close and lock the  
drain valve by pushing inward and turning clockwise  
until the pin is in the locked position as shown.  
Remove the drain tube and replace the cap onto to the  
bottom fitting of the drain valve.  
Refill engine with oil through oil fill dipstick tube. Pour  
slowly. Do not overfill. For approximate capacity see  
“PRODUCT SPECIFICATIONS” section of this man-  
ual.  
ENGINE  
LUBRICATION  
Only use high quality detergent oil rated with API service  
classification SG-SL. Select the oil’s SAE viscosity grade  
according to your expected operating temperature.  
•
•
SAE VISCOSITY GRADES  
•
Use gauge on oil fill cap/dipstick for checking level.  
Insert dipstick into the tube and rest the oil fill cap on  
the tube. Do not thread the cap onto the tube when  
taking reading. Keep oil at “FULL” line on dipstick.  
Tighten cap onto the tube securely when finished.  
10W30  
5W-30  
-20  
0
30  
32 40  
0
100  
60  
80  
F
C
-20  
10  
-30  
-10  
20  
30  
40  
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE  
oil_visc_chart4_e  
FIG. 24  
CLEAN AIR SCREEN  
Change the oil after every 50 hours of operation or at least  
once a year if the tractor is not used for 50 hours in one  
year.  
Air screen must be kept free of dirt and chaff to prevent  
engine damage from overheating. Clean with a wire brush  
or compressed air to remove dirt and stubborn dried gum  
fibers.  
Check the crankcase oil level before starting the engine  
and after each eight (8) hours of operation.  
AIR FILTER  
Your engine will not run properly using a dirty air filter.  
Service air cleaner more often under dusty conditions. See  
Engine Manual.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
ENGINE OIL FILTER  
Replace the engine oil filter every season or every other  
oil change if the tractor is used more than 100 hours in  
one year.  
CLAMP  
CLAMP  
FUEL FILTER  
MUFFLER  
Inspect and replace corroded muffler and spark arrester  
(if equipped) as it could create a fire hazard and/or dam-  
age.  
FIG. 26  
CLEANING  
SPARK PLUGS  
•
•
•
Clean engine, battery, seat, finish, etc. of all foreign  
Replace spark plugs at the beginning of each mowing  
season or after every 100 hours of operation, whichever  
occurs first. Spark plug type and gap setting are shown in  
“PRODUCT SPECIFICATIONS” section of this manual.  
matter.  
Keep finished surfaces and wheels free of all gasoline,  
oil, etc.  
Protect painted surfaces with automotive type wax.  
IN-LINE FUEL FILTER (See Fig. 26)  
The fuel filter should be replaced once each season. If fuel  
filter becomes clogged, obstructing fuel flow to carburetor,  
replacement is required.  
We do not recommend using a garden hose or pressure  
washer to clean your tractor unless the engine and trans-  
mission are covered to keep water out. Water in engine or  
transmission will shorten the useful life of your tractor. Use  
compressed air or a leaf blower to remove grass, leaves  
and trash from tractor and mower.  
•
•
•
•
With engine cool, remove filter and plug fuel line sec-  
tions.  
Place new fuel filter in position in fuel line with arrow  
pointing towards carburetor.  
Be sure there are no fuel line leaks and clamps are  
properly positioned.  
Immediately wipe up any spilled gasoline.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST-  
MENTS:  
•
•
•
•
•
Depress brake pedal fully and set parking brake.  
Place attachment clutch in “DISENGAGED” position.  
Turn ignition key to “STOP” and remove key.  
Make sure the blades and all moving parts have completely stopped.  
Disconnect spark plug wire from spark plug and place wire where it cannot come in contact  
with plug.  
•
From right side of mower, disconnect anti-sway bar (S)  
from right rear mower bracket (D) - remove retainer  
spring and washer and pull mower toward you until  
the bar falls from the hole in bracket.  
TRACTOR (See Fig. 27)  
TO REMOVE MOWER  
•
•
•
Place attachment clutch in “DISENGAGED” position.  
Lower attachment lift lever to its lowest position.  
Disengage belt tension rod (K) from lock bracket (L).  
•
•
Turn tractor steering wheel to the left as far as it will  
go.  
Slide mower out from under right side of tractor.  
CAUTION: Belt tension rod is spring  
loaded. Have a tight grip on rod and  
release slowly.  
TO INSTALL MOWER  
Follow procedure described in “INSTALL MOWER AND  
DRIVE BELT” in the Assembly section of this manual.  
•
•
Remove mower belt from electric clutch pulley (M).  
Disconnect front link (E) from mower - remove retainer  
spring and washer.  
Go to either side of mower and disconnect mower  
suspension arm (A) from chassis and rear lift link (C)  
from rear mower bracket (D) - remove retainer springs  
and washers.  
TO LEVEL MOWER  
Make sure tires are properly inflated to the PSI shown on  
tires. If tires are over or under inflated, it may affect the  
appearance of your lawn and lead you to think the mower  
is not adjusted properly.  
•
VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 28)  
•
Go to other side of mower and disconnect the suspen-  
sion arm and rear lift link.  
•
With all tires properly inflated and if your lawn appears  
unevenly cut, determine which side of mower is cutting  
lower.  
CAUTION: After rear lift links are dis-  
connected,theattachmentliftleverwill  
be spring loaded. Have a tight grip on  
lift lever when changing position of  
the lever.  
NOTE: As desired, you can raise the low side of mower or  
lower the high side.  
L
B
M
K
F
A
E
H
S
C
D
FIG. 27  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
•
•
Go to side of mower you wish to adjust.  
FRONT-TO-BACK ADJUSTMENT (See Figs. 30 and 31)  
IMPORTANT: Deck must be level side-to-side.  
With a 3/4" or adjustable wrench, turn lift link adjust-  
ment nut (A) to the left to lower the mower, or, to the  
right to raise the mower.  
To obtain the best cutting results, the mower blades should  
be adjusted so the front tip is 1/8" to 1/2" lower than the  
rear tip when the mower is in its highest position.  
CAUTION: Blades are sharp. Protect  
your hands with gloves and/or wrap  
blade with heavy cloth.  
A
•
•
Raise mower to highest position.  
Positionanybladesothetipispointingstraightforward.  
Measure distance (B) to the ground at front and rear  
tip of the blade.  
•
•
•
If front tip of blade is not 1/8" to 1/2" lower than the rear  
tip, go to the front of tractor.  
With an 11/16" or adjustable wrench, loosen jam nut  
A several turns to clear adjustment nut B.  
With a 3/4" or adjustable wrench, turn front link adjust-  
ment nut (B) clockwise (tighten) to raise the front of  
mower, or, counterclockwise (loosen) to lower the front  
mower.  
Turn nut left  
to lower mower  
Turn nut right  
to raise mower  
02948  
FIG. 28  
02548  
NOTE: Each full turn of adjustment nut will change mower  
height about 3/16".  
•
Test your adjustment by mowing some uncut grass  
and visually checking the appearance. Readjust, if  
necessary, until you are satisfied with the results.  
B
B
PRECISION SIDE-TO-SIDE ADJUSTMENT  
(See Fig. 29)  
FIG. 30  
•
With all tires properly inflated, park tractor on level  
ground or driveway.  
CAUTION: Blades are sharp. Protect  
your hands with gloves and/or wrap  
blade with heavy cloth.  
B
•
•
Raise mower to its highest position.  
A
At both sides of mower, position blade at side and  
measure the distance (A) from bottom edge of blade  
to the ground. The distance should be the same on  
both sides.  
•
•
If adjustment is necessary, see steps 2 and 3 in Visual  
Adjustment instructions above.  
Recheck measurements, adjust if necessary until both  
sides are equal.  
Tighten adjust nut  
B to raise mower  
Loosen adjust nut  
B to lower mower  
02966  
02950  
Loosen jam nut A first  
A
A
FIG. 31  
FIG. 29  
NOTE: Each full turn of the adjustment nut will change  
mower height about 1/8".  
•
•
Recheck measurements, adjust if necessary until front  
tip of blade is 1/8" to 1/2" lower than the rear tip.  
Holdadjustmentnutinpositionwithwrenchandtighten  
jam nut securely against adjustment nut.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REPLACE MOWER BLADE DRIVE BELT  
TO CHECK BRAKE  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be serviced.  
MOWER DRIVE BELT REMOVAL (See Fig. 32)  
•
Park tractor on a level surface. Engage parking  
brake.  
•
•
Lower attachment lift lever to its lowest position.  
Disengage belt tension rod (K) from lock bracket (L).  
You may also check brake by:  
•
Park tractor on a level, dry concrete or paved surface,  
depress brake pedal all the way down and engage  
parking brake.  
CAUTION: Belt tension rod is spring  
loaded. Have a firm grip on rod and  
release slowly.  
•
Disengage transmission by placing freewheel control  
in “transmission disengaged” position. Pull freewheel  
control out and into the slot and release so it is held in  
the disengaged position.  
•
•
Remove screws (P) from mandrel covers (Q) and re-  
move covers.  
Remove any dirt or grass clippings which may have  
accumulated around mandrels and entire upper deck  
surface.  
The rear wheels must lock and skid when you try to manu-  
ally push the tractor forward. If the rear wheels rotate, then  
the brake needs to be serviced. Contact a qualified service  
center.  
•
Remove belt from electric clutch pulley (M), both man-  
drel pulleys (R) and all idler pulleys (S).  
TO REPLACE MOTION DRIVE BELT  
(See Fig. 33)  
Park the tractor on level surface. Engage parking brake.  
For assistance, there is a belt installation guide decal on  
bottom side of left footrest.  
MOWER DRIVE BELT INSTALLATION  
•
Install belt around all mandrel pulleys (R) and around  
idler pulleys (S) as shown.  
•
Install belt onto electric clutch pulley (M).  
IMPORTANT: Check belt for proper routing in all mower  
BELT REMOVAL -  
pulley grooves.  
•
Remove mower (See “TO REMOVE MOWER” in this  
section of manual).  
•
•
Reassemble mandrel covers (Q). Securely tighten all  
screws.  
Engage belt tension rod (K) on locking bracket (L).  
NOTE: Observe entire motion drive belt and position of all  
belt guides and keepers.  
•
•
•
Disconnect clutch wire harness (A).  
Remove anti-rotation link (B) on right side of tractor.  
Remove belt from stationary idler (C) and clutching  
idler (D).  
CAUTION: Belt tension rod is spring  
loaded. Have a tight grip on rod and  
engage slowly.  
•
•
Remove belt from centerspan idler (E).  
•
Raise attachment lift lever to highest position.  
Pull belt slack toward rear of tractor. Carefully remove  
belt upwards from transmission input pulley and over  
cooling fan blades (F).  
P
Q
•
•
Removebeltdownwardfromenginepulleyandaround  
electric clutch (G).  
Slide belt toward rear of tractor, off the steering plate  
(H) and remove from tractor.  
M
L
P
R
K
BELT INSTALLATION -  
Q
•
•
•
Install new belt from tractor rear to front, over the steer-  
ing plate (H) and above clutch brake pedal shaft (J).  
Pull belt toward front of tractor and roll belt around  
electric clutch and onto engine pulley (G).  
Pullbelttowardrearoftractor.Carefullyworkbeltdown  
around transmission cooling fan and onto the input  
pulley (F). Be sure belt is inside the belt keeper.  
Install belt on centerspan idler (E).  
Install belt through stationary idler (C) and clutching  
idler (D).  
R
S
•
•
R
•
Reinstall anti-rotation link (B) on right side of tractor.  
Tighten securely.  
FIG. 32  
•
•
Reconnect clutch harness (A).  
Make sure belt is in all pulley grooves and inside all  
belt guides and keepers.  
•
Install mower (See “TO INSTALL MOWER” in this sec-  
tion of manual).  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
•
Replace axle cover.  
NOTE: To seal tire punctures and prevent flat tires due to  
slow leaks, tire sealant may be purchased from your local  
parts dealer. Tire sealant also prevents tire dry rot and  
corrosion.  
G
H
WASHERS  
RETAINING  
RING  
B
A
AXLE COVER  
C
J
D
E
SQUARE KEY (REAR  
WHEEL ONLY)  
FIG. 34  
F
TO START ENGINE WITH A WEAK BATTERY  
(See Fig. 35)  
02953  
electric  
WARNING: Lead-acid batteries gen-  
erate explosive gases. Keep sparks,  
flameandsmokingmaterialsawayfrom  
batteries. Always wear eye protection  
when around batteries.  
FIG. 33  
TO CHECK BRAKE  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be serviced.  
If your battery is too weak to start the engine, it should be  
recharged. (See "BATTERY" in the MAINTENANCE sec-  
tion of this manual).  
If “jumper cables” are used for emergency starting, follow  
this procedure:  
IMPORTANT: YOURTRACTORISEQUIPPEDWITHA12VOLT  
SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT  
SYSTEM.DONOTUSEYOURTRACTORBATTERYTOSTART  
OTHER VEHICLES.  
You may also check brake by:  
•
Park tractor on a level, dry concrete or paved surface,  
depress brake pedal all the way down and engage  
parking brake.  
Disengage transmission by placing freewheel control  
in “transmission disengaged” position. Pull freewheel  
control out and into the slot and release so it is held in  
the disengaged position.  
•
TO ATTACH JUMPER CABLES -  
•
Connect one end of the RED cable to the POSITIVE  
(+) terminal of each battery(A-B), taking care not to  
short against tractor chassis.  
The rear wheels must lock and skid when you try to manu-  
ally push the tractor forward. If the rear wheels rotate, then  
the brake needs to be serviced. Contact a qualified service  
center.  
•
•
ConnectoneendoftheBLACKcabletotheNEGATIVE  
(-) terminal (C) of fully charged battery.  
Connect the other end of the BLACK cable (D) to good  
chassis ground, away from fuel tank and battery.  
FRONT WHEEL TOE-IN/CAMBER  
Your new tractor front wheel toe-in and camber is set at the  
factory and is normal. The front wheel toe-in and camber  
are not adjustable. If damage has occurred to affect the  
factory set front wheel toe-in or camber, contact a qualified  
service center.  
TO REMOVE CABLES, REVERSE ORDER -  
•
BLACK cable first from chassis and then from the fully  
charged battery.  
•
RED cable last from both batteries.  
TO REMOVE WHEEL FOR REPAIRS  
(See Fig. 34)  
•
•
Block up axle securely.  
Removeaxlecover,retainingringandwasherstoallow  
wheel removal (rear wheel contains a square key - Do  
not lose).  
•
•
Repair tire and reassemble.  
On rear wheels only: align grooves in rear wheel hub  
and axle. Insert square key.  
WEAK OR DEAD  
BATTERY  
FULLY CHARGED  
BATTERY  
•
Replace washers and snap retaining ring securely in  
axle groove.  
FIG. 35  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REPLACE HEADLIGHT BULB  
•
•
Raise hood.  
HOOD  
Pull bulb holder out of the hole in the backside of the  
grill.  
•
•
Replace bulb in holder and push bulb holder securely  
back into the hole in the backside of the grill.  
Close hood.  
HEADLIGHT  
WIRE  
CONNECTOR  
INTERLOCKS AND RELAYS  
Loose or damaged wiring may cause your tractor to run  
poorly, stop running, or prevent it from starting.  
•
Check wiring. See electrical wiring diagram in the  
Repair Parts section.  
02778  
TO REPLACE FUSE  
Replace with 20 amp automotive-type plug-in fuse. The  
fuse holder is located behind the dash.  
FIG. 36  
TO REMOVE HOOD AND GRILL ASSEMBLY  
(See Fig. 36)  
•
•
•
Raise hood.  
ENGINE  
Unsnap headlight wire connector.  
Standinfrontoftractor. Grasphoodatsides, tilttoward  
engine and lift off of tractor.  
TO ADJUST THROTTLE CONTROL CABLE  
The throttle control has been preset at the factory and  
adjustment should not be necessary. If adjustment is nec-  
essary, see engine manual.  
•
To replace, reverse above procedure.  
TO ADJUST CHOKE CONTROL  
The choke control has been preset at the factory and ad-  
justment should not be necessary. If adjustment is neces-  
sary, see engne manual.  
TO ADJUST CARBURETOR  
Your carburetor is not adjustable. If your engine does not  
operate properly due to suspected carburetor problems,  
take your tractor to an authorized service center for repair  
and/or adjustment.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STORAGE  
Immediately prepare your tractor for storage at the end  
of the season or if the tractor will not be used for 30 days  
or more.  
ENGINE  
FUEL SYSTEM  
IMPORTANT: ITISIMPORTANTTOPREVENTGUMDEPOSITS  
FROMFORMINGINESSENTIALFUELSYSTEMPARTSSUCH  
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK  
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT  
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING  
ETHANOLORMETHANOL)CANATTRACTMOISTUREWHICH  
LEADSTOSEPARATIONANDFORMATIONOFACIDSDURING  
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM  
OF AN ENGINE WHILE IN STORAGE.  
WARNING: Neverstorethetractorwith  
gasoline in the tank inside a building  
where fumes may reach an open flame  
orspark. Allowtheenginetocoolbefore  
storing in any enclosure.  
TRACTOR  
Removemowerfromtractorforwinterstorage. Whenmower  
istobestoredforaperiodoftime,cleanitthoroughly,remove  
all dirt, grease, leaves, etc. Store in a clean, dry area.  
•
•
•
Empty the fuel tank by starting the engine and let it run  
until the fuel lines and carburetor are empty.  
Never use engine or carburetor cleaner products in the  
fuel tank or permanent damage may occur.  
•
Clean entire tractor (See “CLEANING” in the Mainte-  
nance section of this manual).  
Inspect and replace belts, if necessary (See belt re-  
placement instructions in the Service andAdjustments  
section of this manual).  
Lubricate as shown in the Maintenance section of this  
manual.  
Be sure that all nuts, bolts and screws are securely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
Use fresh fuel next season.  
NOTE: Fuel stabilizer is an acceptable alternative in mini-  
mizing the formation of fuel gum deposits during storage.  
Add stabilizer to gasoline in fuel tank or storage container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to  
allow the stabilizer to reach the carburetor. Do not empty  
the gas tank and carburetor if using fuel stabilizer.  
•
•
•
ENGINE OIL  
Drain oil (with engine warm) and replace with clean en-  
gine oil. (See “ENGINE” in the Maintenance section of  
this manual).  
•
Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
BATTERY  
CYLINDER(S)  
•
•
Fully charge the battery for storage.  
•
•
Remove spark plug(s).  
Pour one ounce of oil through spark plug hole(s) into  
cylinder(s).  
After a period of time in storage, battery may require  
recharging.  
To help prevent corrosion and power leakage during  
long periods of storage, battery cables should be dis-  
connected and battery cleaned thoroughly (see “TO  
CLEAN BATTERY AND TERMINALS” in the Mainte-  
nance section of this manual).  
•
•
•
Turn ignition key to “START” position for a few seconds  
to distribute oil.  
Replace with new spark plug(s).  
•
•
After cleaning, leave cables disconnected and place  
cables where they cannot come in contact with battery  
terminals.  
If battery is removed from tractor for storage, do not  
store battery directly on concrete or damp surfaces.  
OTHER  
•
•
Do not store gasoline from one season to another.  
Replace your gasoline can if your can starts to rust.  
Rust and/or dirt in your gasoline will cause problems.  
•
•
If possible, store your tractor indoors and cover it to  
give protection from dust and dirt.  
Cover your tractor with a suitable protective cover that  
does not retain moisture. Do not use plastic. Plastic  
cannot breathe which allows condensation to form and  
will cause your tractor to rust.  
IMPORTANT: NEVERCOVERTRACTORWHILEENGINE AND  
EXHAUST AREAS ARE STILL WARM.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
Will not start  
CAUSE  
CORRECTION  
1. Out of fuel.  
1. Fill fuel tank.  
2. Engine not “CHOKED” properly.  
3. Engine flooded.  
4. Bad spark plug.  
5. Weak or dead battery.  
6. Dirty air filter.  
2. See “TO START ENGINE” in Operation section.  
3. Wait several minutes before attempting to start.  
4. Replace spark plug.  
5. Recharge or replace battery.  
6. Clean/replace air filter.  
7. Dirty fuel filter.  
7. Replace fuel filter.  
8. Water in fuel.  
8. Empty fuel tank and carburetor, refill tank with  
fresh gasoline and replace fuel filter.  
9. Check all wiring.  
9. Loose or damaged wiring.  
10. Carburetor out of adjustment.  
10. See “To Adjust Carburetor” in Service Adjust  
ments section.  
11. Engine valves out of adjustment.  
11. Contact an authorized service center/  
department.  
Hard to start  
1. Dirty air filter.  
1. Clean/replace air filter.  
2. Replace spark plug.  
3. Recharge or replace battery.  
4. Replace fuel filter.  
2. Bad spark plug.  
3. Weak or dead battery.  
4. Dirty fuel filter.  
5. Stale or dirty fuel.  
5. Empty fuel tank and refill tank with fresh, clean  
gasoline.  
6. Loose or damaged wiring.  
7. Carburetor out of adjustment.  
6. Check all wiring.  
7. See “To Adjust Carburetor” in Service Adjust  
ments section.  
8. Engine valves out of adjustment.  
8. Contact an authorized service center/  
department.  
Engine will not  
turn over  
1. Brake pedal not depressed.  
2. Attachment clutch is engaged.  
3. Weak or dead battery.  
1. Depress brake pedal.  
2. Disengage attachment clutch.  
3. Recharge or replace battery.  
4. Replace fuse.  
4. Blown fuse.  
5. Corroded battery terminals.  
6. Loose or damaged wiring.  
7. Faulty ignition switch.  
8. Faulty solenoid or starter.  
9. Faulty operator presence switch(es).  
5. Clean battery terminals.  
6. Check all wiring.  
7. Check/replace ignition switch.  
8. Check/replace solenoid or starter.  
9. Contact an authorized service center/  
department.  
Engine clicks but  
will not start  
1. Weak or dead battery.  
1. Recharge or replace battery.  
2. Clean battery terminals.  
3. Check all wiring.  
2. Corroded battery terminals.  
3. Loose or damaged wiring.  
4. Faulty solenoid or starter.  
4. Check/replace solenoid or starter.  
Loss of power  
1. Cutting too much grass/too fast.  
2. Throttle in “CHOKE” position.  
1. Raise cutting height/reduce speed.  
2. Adjust throttle control.  
3. Build-up of grass, leaves and trash under mower. 3. Clean underside of mower housing.  
4. Dirty air filter.  
4. Clean/replace air filter.  
5. Low oil level/dirty oil.  
6. Faulty spark plug.  
7. Dirty fuel filter.  
5. Check oil level/change oil.  
6. Clean and regap or change spark plug.  
7. Replace fuel filter.  
8. Stale or dirty fuel.  
8. Empty fuel tank and refill tank with fresh, clean  
gasoline.  
9. Water in fuel.  
9. Empty fuel tank and carburetor, refill tank with  
fresh gasoline and replace fuel filter.  
10. Connect and tighten spark plug wire.  
11. Clean engine air screen/fins.  
12. Clean/replace muffler.  
10. Spark plug wire loose.  
11. Dirty engine air screen/fins.  
12. Dirty/clogged muffler.  
13. Loose or damaged wiring.  
14. Carburetor out of adjustment.  
13. Check all wiring.  
14. See “To Adjust Carburetor” in Service Adjust  
ments section.  
15. Engine valves out of adjustment.  
15. Contact an authorized service center/  
department.  
Excessive vibration  
1. Worn, bent or loose blade.  
2. Bent blade mandrel.  
1. Replace blade. Tighten blade bolt.  
2. Replace blade mandrel.  
3. Loose/damaged part(s).  
3. Tighten loose part(s). Replace damaged parts.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Engine dies when  
tractor is shifted  
into reverse  
1. Reverse operation system  
(ROS) is not "ON" while  
mower or other attachment  
is engaged.  
1. Turn ignition key to  
ROS "ON" position.  
See Operation section.  
Engine continues to  
run when operator  
leaves seat with  
attachment clutch  
engaged  
1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not  
corrected, contact an authorized service center/  
department.  
Poor cut - uneven  
1. Worn, bent or loose blade.  
2. Mower deck not level.  
1. Replace blade. Tighten blade bolt.  
2. Level mower deck.  
3. Buildup of grass, leaves, and trash under mower. 3. Clean underside of mower housing.  
4. Bent blade mandrel.  
5. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
4. Replace blade mandrel.  
5. Clean around mandrels to open vent holes.  
Mower blades will not  
rotate  
1. Obstruction in clutch mechanism.  
2. Worn/damaged mower drive belt.  
3. Frozen idler pulley.  
1. Remove obstruction.  
2. Replace mower drive belt.  
3. Replace idler pulley.  
4. Frozen blade mandrel.  
4. Replace blade mandrel.  
Poor grass discharge  
1. Engine speed too slow.  
2. Travel speed too fast.  
3. Wet grass.  
4. Mower deck not level.  
5. Low/uneven tire air pressure.  
6. Worn, bent or loose blade.  
1. Place throttle control in “FAST” position.  
2. Shift to slower speed.  
3. Allow grass to dry before mowing.  
4. Level mower deck.  
5. Check tires for proper air pressure.  
6. Replace blade. Tighten blade bolt.  
7. Buildup of grass, leaves and trash under mower. 7. Clean underside of mower housing.  
8. Mower drive belt worn.  
9. Blades improperly installed.  
10. Improper blades used.  
8. Replace mower drive belt.  
9. Reinstall blades sharp edge down.  
10. Replace with blades listed in this manual.  
11. Clogged mower deck vent holes from buildup of 11. Clean around mandrels to open vent holes.  
grass, leaves, and trash around mandrels.  
Headlight(s) not  
working  
(if so equipped)  
1. Light switch is “OFF”.  
2. Bulb(s) or lamp(s) burned out.  
3. Faulty light switch.  
4. Loose or damaged wiring.  
5. Blown fuse.  
1. Turn light switch “ON”.  
2. Replace bulb(s) or lamp(s).  
3. Check/replace light switch.  
4. Check wiring and connections.  
5. Replace fuse.  
Battery will not charge 1. Bad battery cell(s).  
2. Poor cable connections.  
1. Replace battery.  
2. Check/clean all connections.  
3. Replace regulator.  
4. Replace alternator.  
3. Faulty regulator (if so equipped).  
4. Faulty alternator.  
Loss of drive  
1. Freewheel control in “disengaged” position.  
2. Motion drive belt worn, damaged, or broken.  
3. Air trapped in transmission during shipment  
or servicing.  
1. Place freewheel control in “engaged” position.  
2. Replace motion drive belt.  
3. Purge transmission.  
Engine “backfires”  
when turning  
engine “OFF”  
1. Engine throttle control not set between half and 1. Move throttle control between half and full speed  
full speed (fast) position before stopping engine.  
(fast) position before stopping engine.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05  
SCHEMATIC  
02928-194276_Regulated-Tex  
BATTERY  
SOLENOID  
STARTER  
RED  
A
M
RED  
FUSE  
AMMETER  
(OPTIONAL)  
BLACK  
ELECTRIC CLUTCH  
WHITE  
BLACK  
WHITE  
S
WHITE  
M
B
A1  
G
GRAY  
A2  
L
RED  
RED  
CLUTCH/BRAKE  
(PEDAL UP)  
BLACK  
REVERSE SWITCH  
(NOT IN REVERSE)  
PTO SWITCH  
(DISENGAGED)  
BLACK  
BLACK  
BLACK  
2
BLACK  
BLACK  
SEAT SWITCH  
(NOT OCCUPIED)  
BLACK  
BLACK  
3
1
GRAY  
6
JUNCTION  
CONNECTOR  
SHORTING  
CONNECTOR  
CHASSIS  
HARNESS  
SPARK  
IGNITION  
UNIT  
PLUGS GAP  
(2 PLUGS ON  
TWIN CYL. ENGINES)  
(OPTIONAL)  
BLUE  
BLACK  
HOUR  
METER  
FUEL  
LINE  
12V  
POWER OUTLET  
(IF SO EQUIPPED)  
BLUE  
CHARGING SYSTEM OUTPUT  
15 AMP DC @ 36 RPM  
FUEL SHUT-OFF  
SOLENOID  
(IF SO EQUIPPED)  
REGULATOR  
RED  
STATOR  
28 VOLTS AC @ 3600 RPM (REGULATOR DISCONNECTED)  
BLACK  
BROWN  
LIGHT  
SWITCH  
HEADLIGHTS  
WIRING INSULATED CLIPS  
NOTE: IF WIRING INSULATED  
CLIPS WERE REMOVED FOR  
SERVICING OF UNIT, THEY  
SHOULD BE REPLACED TO  
PROPERLY SECURE YOUR  
WIRING.  
3
6
6
5
3
2
IGNITION SWITCH  
NON-REMOVABLE  
CONNECTIONS  
2
1
5
4
POSITION CIRCUIT “MAKE”  
4
1
OFF  
RUN/OVERRIDE  
M+G+A1  
B+A1  
REMOVABLE  
CONNECTIONS  
CHASSIS HARNESS  
CONNECTOR  
DASH HARNESS  
CONNECTOR  
RUN  
B+A1  
L+A2  
START B + S + A1  
02928  
(MATING SIDE)  
(MATING SIDE)  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05  
ELECTRICAL  
22  
90  
21  
41  
24  
43  
42  
40  
27  
33  
30  
25  
34  
46  
27  
50  
2
1
26  
91  
99  
100  
16  
8
71  
29  
55  
28  
194276D  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05  
ELECTRICAL  
KEY PART  
NO. NO.  
DESCRIPTION  
1
532 14 49-27 Battery  
2
874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4  
532 18 64-91 Battery Box  
8
16  
21  
22  
24  
25  
26  
27  
28  
29  
30  
33  
34  
40  
41  
42  
43  
46  
50  
55  
71  
90  
91  
99  
532 17 61-38 Switch Interlock  
532 18 37-59 Harness Socket Light  
532 00 41-52 Bulb, Light # 1156  
532 40 02-53 Cable Battery  
532 19 88-93 Cable Starter  
532 17 51-58 Fuse  
873 51 04-00 Nut Keps Hex 1/4-20 unc  
532 14 54-91 Cable Ground 21" Blk 6 Ga.  
532 40 15-45 Switch Seat  
532 19 33-50 Switch Ignition  
532 14 04-01 Key Ignition Molded Generic  
532 11 07-12 Switch Light/Reset  
532 40 11-05 Harness Ignition Dash  
871 72 04-08 Screw Thd Cut 1/4-20 x 1/2  
532 13 15-63 Cover Terminal Red  
532 19 25-07 Solenoid  
532 19 81-38 Gauge Hourmeter  
532 17 46-51 Switch PTO  
817 49 05-12 Screw Thdrol 5/16-18 x 3/4  
532 19 42-76 Harness Ignition Chassis  
532 18 04-49 Cover Terminal Battery  
532 19 02-70 Strap Battery  
817 67 04-12 Screw Hexwsh Thdrol 1/4-20 x 3/4  
100 819 09 14-16 Washer 9/32 x 7/8 x 16 Ga.  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05  
CHASSIS  
15  
208  
204  
18  
210  
212  
214  
203  
25  
14  
207  
130  
211  
206  
209  
130  
5
176  
202  
176  
205  
176  
175  
177  
150  
178  
161  
196  
221  
176  
37  
176  
182  
36  
162  
199  
130  
184  
194  
181  
34  
68  
36  
194  
130  
52  
218  
180  
52  
165  
213  
139  
68  
162  
189  
213  
139  
183  
217  
228  
152  
181  
52  
58  
189  
228  
68  
189  
189  
99  
1
chassis-tex_10-gt-husq  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05  
CHASSIS  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
5
532 40 18-23 Dash  
184 532 19 57-80 Spacer Fender  
185 872 11 05-10 Bolt Carr. 5/16-18 x 1-1/4 Gr.5  
189 817 00 05-12 Screw 5/16-18 x 3/4  
194 873 90 05-00 Nut Lock Hex Flange 5/16-18  
196 532 40 02-99 Console Asm. Deck Lift  
199 532 19 82-59 Plate Deck Lift  
14  
15  
18  
25  
34  
37  
52  
58  
68  
99  
532 40 18-24 Hood  
532 19 89-07 Lens LH  
532 40 02-97 Grille  
532 19 89-06 Lens RH  
532 19 61-25 Plate Engine  
532 40 18-25 Fender  
202 532 40 30-48 Vent Side Hood RH  
203 532 40 30-76 Vent Side Hood LH  
204 532 19 89-04 Vent Asm Hood Top  
205 532 40 17-09 Skirt Hood Side RH  
206 532 40 17-11 Skirt Hood Side LH  
207 532 19 71-98 Bezel RH  
873 68 05-00 Nut Crown Lock 5/16-18  
532 19 43-14 Bracket Fender  
817 49 05-08 Screw 5/16-18 x 1/2  
532 19 82-53 Rod Bypass Asm.  
130 532 19 16-11 Screw 10 x 3/4 Single Lead Hex  
139 532 17 18-73 Bolt Shoulder 5/16-18  
150 532 19 85-12 Duct Heat Hood  
208 532 19 71-99 Bezel LH  
209 532 19 91-30 Insert Hex Top RH  
210 532 19 91-31 Insert Hex Top LH  
211 532 19 91-32 Insert Hex Bottom RH  
212 532 19 91-33 Insert Hex Bottom LH  
213 874 76 05-12 Bolt Hex Hd 5/16-18 unc x 3/4  
214 532 19 91-45 Clip Retainer  
152 532 19 95-35 Shield Browning  
156 817 00 05-12 Screw 5/16-18 x 3/4  
161 532 40 18-26 Console Fuel Window  
162 532 14 24-32 Screw Hex Wsh Hi-Lo 1/4 x 1/2  
165 532 19 68-26 Bracket Support Tank  
175 532 19 63-04 Crossmember  
176 532 40 07-76 Screw 10-24 x 5/8 RND Qdrx  
177 532 19 52-27 Bushing Steering  
178 532 19 97-82 Cargo Asm. Net  
217 532 15 65-24 Rod Pivot  
218 532 19 63-95 Hood Stop  
221 532 19 89-09 Reflector LH  
228 532 19 51-61 Stud Fastener  
180 532 40 15-59 Chassis  
181 532 40 30-25 Bushing Mtg. Fender Crgo.  
182 532 19 47-87 Dash Lower  
- -  
532 40 41-37 Plug Hole Dash Lower  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05  
DRIVE  
74  
221  
220  
56  
70  
213  
206  
125  
74  
207  
26  
209  
96  
218  
143  
197  
116  
196  
216  
219  
171  
125  
221 184  
42  
125  
35  
80  
160  
203  
64  
167  
160  
170  
188  
52  
185  
51  
214  
186  
189  
208  
210  
125  
153  
49  
15  
159  
15  
187  
50  
161  
211  
116  
29  
51  
163  
215  
190  
159  
211  
166  
52  
51  
33  
9
7
116  
17  
162  
169  
162  
2
205  
37  
183  
2
7
37  
169  
1
205  
183  
33  
drive-tex_6-husq-hydro-0610  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05  
DRIVE  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
166 532 19 72-90 Nut Push .625  
1
- - - - - -  
Transaxle, Hydro HG-0610  
(Order Parts from Transaxle Manu-  
facturer)  
167 532 19 62-11 Latch Brake Parking  
169 874 49 05-60 Bolt Hex Flghd 5/16-18 x 3.75  
170 532 19 43-22 Keeper Belt Centerspan  
171 872 11 06-16 Bolt  
2
532 18 62-11 Key 1/4 x 2.5  
7
532 19 98-44 Hub Asm. Wheel  
532 14 00-80 Bolt Hub Wheel  
819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.  
532 19 72-96 Spring, Brake  
183 532 40 04-24 Spacer Split  
9
184 532 40 31-18 Handle Parking Brake  
185 872 11 06-20 Bolt Rdhd Sqnk 3/8-16 x 2-1/2  
186 532 19 43-21 Spacer Retainer  
15  
17  
26  
29  
33  
35  
37  
42  
49  
50  
51  
52  
56  
64  
70  
74  
80  
96  
532 19 96-79 Spring Return Cruise  
532 19 94-67 Rod, Brake  
812 00 00-11 Ring E  
532 19 95-91 Rod, Brake, Park  
532 12 17-49 Washer  
532 12 48-72 Cover, Foot Pedal  
872 11 06-14 Bolt  
532 19 43-27 Pulley Idler Flat  
873 90 06-00 Lock Nut 3/8-16  
532 19 43-26 Idler V-Groove 910" Offset  
532 14 02-18 V-Belt, Drive  
532 19 78-65 Shaft Asm. Pedal Brake Control  
532 40 05-30 Control Asm.  
532 14 24-32 Screw 1/4 x 1/2  
532 40 05-07 Bracket Strap Torque  
874 76 05-20 Bolt Fin Hex 5/16-18 unc x 1.25  
187 819 13 32-10 Washer  
188 532 19 43-23 Link Clutch Ground Drive  
189 532 19 43-17 Bellcrank Ground Drive  
190 532 19 43-18 Keeper Bellcrank Ground Drive  
196 817 00 06-16 Screw 3/8-16 x 1  
197 532 19 97-69 Bracket Clutch Anti-Rotation  
203 819 11 11-16 Washer 11/32 x 11/16 x 16 Ga.  
205 532 12 17-48 Washer  
206 532 19 78-67 Bracket Mount Latch Cruise  
207 532 19 78-68 Latch Control Cruise  
208 532 19 78-69 Gear Sector Control Cruise  
209 532 19 95-92 Rod Control Cruise  
210 532 19 78-60 Rocker Asm. Pedal Control  
211 532 12 01-83 Bearing Nylon  
213 532 40 31-19 Knob Control Cruise  
214 532 40 17-22 Pedal Forward  
215 532 40 17-23 Pedal Reverse  
216 532 19 61-31 Bracket Pulley Idler  
218 874 78 05-20 Bolt Fin Hex 5/16-18 unc x 1-1/4  
219 532 19 57-80 Spacer Fender  
220 532 19 89-08 Reflector RH  
221 532 40 31-87 Retainer Spring Clip Handler  
116 873 90 05-00 Nut Lock Hex Flange 5/16-18  
125 817 00 05-12 Screw 5/16-18 x 3/4  
148 817 00 06-12 Screw 3/8-16 x 3/4  
153 532 12 47-88 Retainer Spring 1"  
159 876 02 04-12 Pin Cotter 1/8 x 3/4  
160 532 16 94-84 Retainer Clip  
161 532 19 54-03 Spring, Return, Clutch  
162 532 19 57-85 Spacer Transaxle  
163 532 19 90-00 Rod Pedal Control  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05  
STEERING ASSEMBLY  
26  
45  
51  
1
21  
63  
19  
60  
16  
9
7
57  
63  
6
61  
8
66  
67  
2
59  
9
8
7
4
35  
58  
64  
67  
6
28  
15  
70  
14  
5
13  
22  
69  
68  
62  
13  
14  
15  
8
53  
steering-tex_4-husq  
13  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
51  
53  
873 94 08-00 Nut Hex Jam Toplock 1/2-20 unf  
532 18 89-67 Washer Hardened .793 x 1.637 x  
.060  
1
532 19 36-51 Wheel, Steering  
532 19 59-68 Axle Asm., Front  
532 19 79-37 Spindle Asm., LH  
532 19 79-36 Spindle Asm., RH  
532 12 49-31 Bearing, Race Thrust Harden  
532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.  
812 00 00-29 Ring, Klip #T5304-75  
532 12 12-32 Cap, Spindle  
532 12 17-49 Washer 25/32 x 1-1/4 x 16 Ga.  
810 04 06-00 Washer, Lock Hvy Hlcl Spr 3/8  
873 54 06-00 Nut, Crown Lock 3/8-24 unf  
532 19 47-46 Shaft Steering  
532 19 47-29 Plate Steering  
532 18 67-37 Adapter, Wheel Steering  
532 19 48-45 Bushing, Strg. Blk  
532 19 36-52 Insert, Wheel Steering  
817 00 06-12 Screw 3/8-16 x 3/4  
532 19 47-32 Gear, Sector Plate  
819 18 38-12 Washer 9/16 x 2-3/8 x 12 Ga.  
2
4
57  
58  
59  
60  
61  
62  
63  
64  
66  
67  
68  
69  
70  
532 19 72-46 Bracket Upstop  
5
532 19 47-47 Bolt Shoulder Sector Pivot CFM  
532 19 47-48 Washer Thrust Sector Steering  
873 97 10-00 Nut Flange Lock 5/8-11  
532 19 47-40 Draglink LH  
6
7
8
9
532 19 47-41 Draglink, RH  
13  
14  
15  
16  
19  
21  
22  
26  
28  
35  
45  
817 00 05-12 Screw 5/16-18 x 3/4  
532 19 98-49 Retainer Clip Spring Steering  
871 02 07-48 Bolt Hex Fghd 7/16-14 x 3 Serr  
532 19 47-37 Bushing PM Front Axle  
873 90 07-00 Nut Lock Flange 7/16-14 Gr. 5  
532 19 91-62 Washer 1.5 x .505 x .118  
532 19 61-97 Bracket Deck Susp. Front  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05  
ENGINE  
1
21  
20  
87  
81  
82  
22  
18  
84  
62  
45  
15  
69  
37  
85  
12  
28  
31  
70  
11  
71  
37  
86  
41  
42  
2
9
29  
90  
SPARK ARRESTER KIT  
engine-tex_14-kohl  
KEY PART  
NO. NO.  
KEY PART  
DESCRIPTION  
Engine KOHL Model No. SV740  
NO. NO.  
DESCRIPTION  
1
- - - - - -  
70  
71  
81  
82  
84  
85  
86  
87  
90  
91  
532 14 66-99 Tube Exhaust LH  
2
532 14 97-23 Muffler  
532 14 67-00 Tube Exhaust RH  
9
532 19 43-19 Keeper Belt Engine  
532 17 93-35 Clutch Electric  
532 40 24-63 Pulley Engine  
532 14 84-56 Tube Drain Oil Easy  
532 18 16-54 Plug Drain Oil  
11  
12  
15  
18  
20  
21  
22  
28  
29  
31  
37  
41  
42  
45  
62  
69  
817 06 06-20 Screw 3/8-16 x 1 1/4  
532 17 99-53 Bolt Hex 7/16-20 x 3.75 Gr. 5  
532 18 43-62 Nut Hex Flange Toplock M8-1.25  
532 19 82-39 Bolt 5/16-18 unc x 1 w/Sems  
817 00 06-16 Screw 3/8-16 x 1  
532 19 34-99 Tank Fuel 4.0  
532 19 42-67 Cap Asm  
532 18 29-37 Control Throttle  
532 19 16-11 Screw 10 x 3/4 Single Lead Hex  
532 19 15-96 Control Choke  
532 14 21-58 Fuel Line  
532 18 74-95 Bushing  
NOTE: All component dimensions given in U.S. inches  
532 13 71-80 Spark Arrester Kit  
532 14 50-06 Clip Push-In  
1 inch = 25.4 mm  
For engine service and replacement parts, call the toll free  
number for your engine manufacturer listed below:  
Briggs & Stratton  
Kohler Co.  
Tecumseh Products  
Honda Engines  
Kawasaki  
532 12 34-87 Clamp Hose  
532 12 61-97 Washer 1-1/2 OD x 15/32 ID x .250  
810 04 07-00 Washer Lock 7/16  
873 51 04-00 Nut Keps Hex 1/4-20 unc  
532 14 66-29 Shield Heat Muffler  
1-800-233-3723  
1-800-544-2444  
1-800-558-5402  
1-800-426-7701  
1-949-460-5688  
- - - - - -  
Gasket (Order parts from engine  
manufacturer)  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05  
SEAT ASSEMBLY  
1
8
8
7
7
41  
40  
10  
21  
6
37  
5
37  
44  
43  
2
21  
3
seat-tex_5-husq  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
37  
40  
41  
43  
44  
873 80 05-00 Nut, Lock 5/16-18 unc  
532 19 76-61 Handle Slide Seat  
532 19 82-00 Spring Latch Seat  
874 76 06-12 Bolt 3/8-16 x 3/4  
1
532 19 75-26 Seat  
2
532 18 01-66 Bracket Pivot Fender  
532 14 06-75 Strap, Asm Fender  
532 14 50-06 Clip, Push In, Hinged  
873 80 06-00 Nut, Lock W/Ins. 3/8-16 unc  
532 12 41-81 Spring, Seat Cprsn  
532 17 18-77 Bolt 5/16-18 uncx 3/4 w/Sems  
532 19 69-77 Pan, Seat  
3
5
819 13 38-12 Washer 13/32 x 2-3/8 x 12 Ga.  
6
7
8
NOTE: All component dimensions given in U.S. inches  
10  
21  
1 inch = 25.4 mm  
532 17 18-52 Bolt, Shoulder 5/16-18  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05  
DECALS  
16  
13  
16  
2
11  
14  
14  
5
3
7
8
9
15  
15  
12  
6
10  
1
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
12  
13  
14  
15  
16  
- -  
- -  
- -  
- -  
- -  
532 16 88-69 Decal, Tick Mark  
1
532 15 97-37 Decal, Brake/Clutch Sym  
532 40 21-28 Decal, Hood Insert  
532 19 63-57 Decal, Warning Deflect. Cutfinger  
532 18 21-66 Decal, Cutfinger CE  
532 19 68-41 Decal, Warning Eng. Syms  
532 14 08-37 Decal Saddle Brake Parking  
532 19 87-85 Decal, Mower Sch.  
532 14 50-05 Decal, Battery Dnge/Poi  
532 17 83-02 Decal, Oper Cruise Sym  
532 40 03-89 Decal, Warning Sym CE  
532 40 44-84 Decal, Steering Whl  
532 40 55-22 Decal, Panel Side  
532 15 97-36 Decal Chassis Hot Muffler  
532 40 33-78 Decal, Hood Logo  
532 16 69-60 Decal, Bypass  
2
3
5
6
7
532 40 17-71 Pad, Footrest, LH  
532 40 37-73 Pad, Footrest, RH  
532 16-25-98 Decal, Drawbar Load  
532 40 33-87 Manual, Owner's (Eng)  
8
9
10  
11  
KEY  
NO.  
PART  
NO.  
WHEELS AND TIRES  
DESCRIPTION  
1
1
532 05 91-92 Cap, Valve, Tire  
2
532 06 51-39 Stem, Valve  
11  
2
3
3
532 14 45-09 Rim Assembly, Front  
532 00 81-34 Tube, Front (Service Item Only)  
532 10 62-30 Tire, Front  
532 00 02-78 Fitting, Grease (Front Wheel Only)  
532 00 90-40 Bearing, Flange (Front Wheel Only)  
532 17 50-39 Cap, Axle (Front Wheel Only)  
532 18 47-08 Tire, Rear  
4
4
10  
5
7
6
5
7
9
8
6
8
9
10  
11  
12  
- -  
532 00 71-54 Tube, Rear (Service Item Only)  
532 40 17-82 Rim Assembly, Rear  
532 00 68-56 Fitting, Grease  
12  
532 14 43-34 Sealant, Tire (10 oz. Tube)  
NOTE: All component dimensions given in U.S. inches  
wheel_art_1-vgt  
1 inch = 25.4 mm  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05  
MOWER DECK  
46  
46  
47  
185  
6
39  
34  
192  
49  
46  
21  
122  
52  
7
114  
43  
196  
49  
97  
33  
33  
98  
32  
52  
33  
32  
31  
31  
1
30  
116  
120  
49  
117  
29  
50  
25  
113  
26  
194  
12  
24  
27  
16  
19  
21  
21  
18  
60  
59  
15  
18  
58  
190  
14  
189  
21  
190  
13  
11  
187  
18  
184  
8
187  
mower_deck 54-tex_3  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05  
MOWER DECK  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
532 19 56-32 Deck Weldment Mower  
532 19 60-66 Cover Mandrel LH  
532 19 71-81 Cover Mandrel RH  
532 17 43-65 Bolt 7/16 Asm. Blade  
532 18 72-56 Blade Bagging  
50  
52  
58  
59  
60  
97  
98  
872 11 06-16 Bolt Rdhd Sqnk 3/8-16 unc x 2  
532 19 61-06 Pulley Idler  
6
7
8
532 18 73-42 Baffle Right  
532 18 73-44 Baffle Left  
11  
12  
- -  
- -  
13  
14  
15  
16  
18  
19  
21  
24  
25  
26  
27  
29  
30  
31  
32  
33  
34  
39  
43  
46  
47  
49  
532 18 76-07 Baffle Center  
532 17 85-15 Washer Hardened  
532 19 61-05 Spring Drive  
532 40 03-37 Rod Anti Sway  
532 18 72-55 Blade Mulching  
532 18 72-54 Blade Hi-Lift  
113 872 11 05-08 Bolt Rdhd Sqnk 5/16-18 x 3/4  
114 532 18 75-56 Rod Tension Relief  
116 532 19 34-06 Bolt, Shoulder  
117 532 17 48-73 Gauge Wheel  
532 18 72-91 Shaft Asm. w/Lower Bearing  
532 18 72-81 Housing, Mandrel  
532 11 04-85 Bearing, Ball, Mandrel  
819 13 13-12 Washer 13/32 x 13/16 x 12 Ga.  
872 14 05-05 Bolt RDHD SQNK 5/16-18 x 5/8  
532 19 42-08 Pin cotter 5/16 Bowtie Lock  
873 68 05-00 Nut, Crownlock 5/16-18 unc  
532 10 53-04 Cap Sleeve  
120 819 13 20-12 Washer 13/32 x 1-1/4 x 12 Ga.  
122 532 18 75-57 Bushing Tension Relief  
184 873 90 05-00 Nut Lock Hex Flange  
185 873 90 07-00 Nut Lock Flange 7/16-14 Gr. 5  
187 532 19 51-61 Stud Fastener w/"D" Anti-Rotation  
189 532 19 51-85 Arm Susp. Mower Rear  
190 532 19 65-39 Bolt Shoulder  
532 17 81-02 Spring, Torsion  
532 11 04-52 Nut, Push  
532 18 89-38 Deflector Shield  
192 532 19 84-68 Keeper Belt Idler  
532 13 14-91 Rod, Hinge  
194 872 14 07-16 Bolt Carr Sqnk 3/8-16 x 2-1/4  
196 872 14 06-20 Bolt Rdhd Sqnk 3/8-16 x 2-1/2 Gr.5  
532 17 39-84 Screw, Thdroll Washer Head  
532 18 76-90 Washer, Spacer Mower Vented  
532 17 34-36 Pulley, Mandrel  
- -  
532 18 72-92 Mandrel Asm. Service (Includes  
Key Nos. 13-15 and 33)  
532 19 93-00 Replacement Mower, Complete  
532 40 02-34 Nut, Flg. Top Lock  
873 68 06-00 Nut Crownlock 3/8-16 unc  
532 19 61-04 Pulley, Idler, Stationary LH  
532 19 60-65 Arm, Idler  
532 13 77-29 Screw, Thdroll. 1/4-20 x 5/8  
532 19 61-03 Belt Deck Drive  
873 90 06-00 Nut, Lock Flg. 3/8-16 unc  
- -  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. YTH2754XP (96041000501), PRODUCT NO. 960 41 00-05  
MOWER LIFT  
7
87  
87  
90  
98  
89  
3
10  
88  
97  
2
97  
91  
87  
89  
lift-tex_3  
89  
87  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
2
532 19 52-23 Shaft Asm., Lift  
90  
91  
97  
98  
532 19 42-08 Pin Cotter 5/16 Bow Tie Lock  
532 40 34-07 Link Lift Susp Mower Rear  
817 06 06-12 Screw 3/8-16 x .75 Smgml Tap/R.Z  
532 19 52-64 Link Lift Susp. Front Mower  
3
532 19 52-30 Lever Asm., Lift Rh  
532 19 64-92 Grip, Lever  
7
10  
87  
88  
89  
532 19 63-14 Spring Torsion  
532 19 42-09 Pin Cotter 7/16 Bow Tie Lock  
532 19 53-04 Spring Lift Assist  
819 19 19-12 Washer Clear Zinc  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
532 40 76-63 07.18.06  
Printed in U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Bolens Lawn Mower 18070S User Manual
Craftsman 196cc Lawn Mower Manual User Manual
Craftsman Lawn Mower 37654 User Manual
Scag Power Equipment Lawn Mower 70001 79999 User Manual
Sears Lawn Aerator S A T 4 0 B H User Manual
Sears Lawn Mower 917_27576 User Manual
Snapper Lawn Mower FRP216012E FRPS216015E NFRP216012E NFRP216012E User Manual
Snapper Lawn Mower NSPV22675HW (7800230) User Manual
Stiga Lawn Mower 13 2511 21 User Manual
Weed Eater Lawn Mower 96022000902 User Manual