Husqvarna Lawn Mower 531 30 96 85 User Manual
03002  
LGT2554  
Owner's Manual / 96045001500 / 2009-01  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY RULES  
Safe Operation Practices for Ride-On Mowers  
GENERAL SERVICE  
III. CHILDREN  
•
Never operate machine in a closed area.  
Keep all nuts and bolts tight to be sure the equipment  
is in safe working condition.  
Tragic accidents can occur if the operator is not alert to  
the presence of children. Children are often attracted to  
the machine and the mowing activity. Never assume that  
children will remain where you last saw them.  
•
•
•
Never tamper with safety devices. Check their proper  
operation regularly.  
•
•
•
•
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Never allow children to operate the machine.  
Useextracarewhenapproachingblindcorners,shrubs,  
trees, or other objects that may block your view of a  
child.  
Keep machine free of grass, leaves, or other debris  
build-up. Cleanoilorfuelspillageandremoveanyfuel-  
soaked debris. Allow machine to cool before storing.  
If you strike a foreign object, stop and inspect the  
machine. Repair, if necessary, before restarting.  
Nevermakeanyadjustmentsorrepairswiththeengine  
running.  
Check grass catcher components and the discharge  
guard frequently and replace with manufacturer's rec-  
ommended parts, when necessary.  
Mower blades are sharp. Wrap the blade or wear  
gloves, and use extra caution when servicing them.  
Check brake operation frequently. Adjust and service  
as required.  
Maintain or replace safety and instruction labels, as  
necessary.  
•
•
•
•
•
•
•
•
IV. TOWING  
•
Tow only with a machine that has a hitch designed for  
towing. Do not attach towed equipment except at the  
hitch point.  
•
•
•
•
Follow the manufacturer's recommendation for weight  
limits for towed equipment and towing on slopes.  
Never allow children or others in or on towed equip-  
ment.  
•
Be sure the area is clear of bystanders before operat-  
ing. Stop machine if anyone enters the area.  
Never carry passengers.  
On slopes, the weight of the towed equipment may  
cause loss of traction and loss of control.  
Travel slowly and allow extra distance to stop.  
•
•
Do not mow in reverse unless absolutely necessary.  
Always look down and behind before and while back-  
ing.  
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Mow up and down slopes (15° Max), not across.  
Choose a low ground speed so that you will not have  
to stop or shift while on the slope.  
Avoid starting, stopping, or turning on a slope. If the  
tires lose traction, disengage the blades and proceed  
slowly straight down the slope.  
V. SERVICE  
SAFE HANDLING OF GASOLINE  
To avoid personal injury or property damage, use extreme  
careinhandlinggasoline. Gasolineisextremelyflammable  
and the vapors are explosive.  
•
•
Extinguish all cigarettes, cigars, pipes, and other  
sources of ignition.  
•
•
•
•
•
Use only approved gasoline container.  
Never remove gas cap or add fuel with the engine  
running. Allow engine to cool before refueling.  
Never fuel the machine indoors.  
•
•
Never store the machine or fuel container where there  
is an open flame, spark, or pilot light such as on a water  
heater or other appliances.  
•
•
•
•
Never fill containers inside a vehicle or on a truck or  
trailer bed with plastic liner. Always place containers  
on the ground away from your vehicle when filling.  
Remove gas-powered equipment from the truck or  
trailer and refuel it on the ground. If this is not possible,  
then refuel such equipment with a portable container,  
rather than from a gasoline dispenser nozzle.  
Keepthenozzleincontactwiththerimofthefueltankor  
container opening at all times until fueling is complete.  
Do not use a nozzle lock-open device.  
If fuel is spilled on clothing, change clothing immedi-  
ately.  
Never overfill fuel tank. Replace gas cap and tighten  
securely.  
•
•
•
If machine stops while going uphill, disengage blades,  
shift into reverse and back down slowly.  
Do not turn on slopes unless necessary, and then, turn  
slowly and gradually downhill, if possible.  
•
•
•
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT SPECIFICATIONS  
CUSTOMER RESPONSIBILITIES  
•
•
Read and observe the safety rules.  
Gasoline Capacity  
and type:  
4 Gallons  
Unleaded Regular  
Follow a regular schedule in maintaining, caring for  
and using your tractor.  
Oil Type (API-SG-SL):  
SAE 30 (above 32°F)  
SAE 5W-30 (below 32°F)  
•
Follow the instructions under “Maintenance” and “Stor-  
age” sections of this owner’s manual.  
Oil Capacity:  
Spark Plug:  
W/ Filter:  
64 oz  
Champion RC12YC  
(Gap: .030")  
WARNING: This tractor is equipped with an internal com-  
bustion engine and should not be used on or near any un-  
improved forest-covered, brush-covered or grass-covered  
land unless the engine’s exhaust system is equipped with  
a spark arrester meeting applicable local or state laws (if  
any). If a spark arrester is used, it should be maintained  
in effective working order by the operator.  
Ground Speed (MPH):  
Forward:  
Reverse:  
0 - 5.5  
0 - 2.4  
Charging System:  
Battery:  
15 AMPS @ 3600 RPM  
AMP/HR:  
28  
230  
U1R  
MIN. CCA:  
Case Size:  
In the state of California the above is required by law  
(Section 4442 of the California Public Resources Code).  
Other states may have similar laws. Federal laws apply  
on federal lands.  
Blade Bolt Torque:  
45-55 FT. LBS.  
A spark arrester for the muffler is available through your  
nearestauthorizedservicecenter/department (SeeREPAIR  
PARTS section of this manual).  
CONGRATULATIONS on your purchase of a new tractor.  
Ithasbeendesigned,engineeredandmanufacturedtogive  
you the best possible dependability and performance.  
Shouldyouexperienceanyproblemyoucannoteasilyrem-  
edy, please contact your nearest authorized servicecenter/  
department We have competent, well-trained technicians  
and the proper tools to service or repair this tractor.  
Please read and retain this manual. The instructions will  
enable you to assemble and maintain your tractor properly.  
Always observe the “SAFETY RULES”.  
TABLE OF CONTENTS  
SAFETY RULES .........................................................2-3  
PRODUCT SPECIFICATIONS....................................... 4  
CUSTOMER RESPONSIBILITIES................................. 4  
ASSEMBLY.................................................................5-8  
OPERATION .............................................................9-15  
MAINTENANCE SCHEDULE ...................................... 16  
MAINTENANCE..................................................... 16-19  
SERVICE AND ADJUSTMENTS............................20-24  
STORAGE.................................................................... 25  
TROUBLESHOOTING............................................26-27  
REPAIR PARTS ......................................................28-42  
WARRANTY.............................................BACK COVER  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
UNASSEMBLED PARTS  
Mower  
Mower Front Wheel  
(5) Large Retainer  
Springs - 7/16  
(1) 3/4 O.D. Washers  
(1) Wheel  
(1) 1-1/4 O.D. Washer  
(2) Smaller Retainer  
Springs - 5/16  
(1) Locknut  
(1) Shoulder Bolt  
3/8-16  
(3) 1-3/16 O.D. Washers  
(1) Anti-Sway Bar  
Slope Sheet  
(1) Oil Drain Tube  
For Future Use  
Keys  
(2) Rear Lift Link  
Assemblies  
(2) Keys  
ASSEMBLY  
Yournewtractorhasbeenassembledatthefactorywithex-  
ceptionofthosepartsleftunassembledforshippingpurposes.  
BEFORE REMOVING TRACTOR FROM  
SKID  
TOOLS REQUIRED FOR ASSEMBLY  
A socket wrench set will make assembly easier. Standard  
wrench sizes are listed.  
TO CHECK BATTERY (See Fig. 1)  
•
Lift hood to raised position.  
NOTE: If this battery is put into service after month and  
year indicated on label (label is located between terminals)  
charge battery for minimum of one hour at 6-10 amps.  
(See "BATTERY" in Maintenance section of this manual  
for charging instructions).  
(2) 7/16" wrenches  
(1) 1/2" wrench  
(1) 3/4" wrench  
Utility knife  
Tire pressure gauge  
Pliers  
(1) 3/4" socket w/drive ratchet  
Whenrightorlefthandismentionedinthismanual,itmeans  
when you are in the operating position (seated behind the  
steering wheel).  
•
For battery and battery cable installation see "RE-  
PLACINGBATTERY"inthe"ServiceandAdjustments"  
section in this manual.  
TO REMOVE TRACTOR FROM  
CARTON  
LABEL  
UNPACK CARTON  
•
Remove all accessible loose parts and parts cartons  
from carton .  
•
Cut along dotted lines on all four panels of carton.  
Remove end panels and lay side panels flat.  
•
•
Remove mower and packing materials.  
Check for any additional loose parts or cartons and  
remove.  
Fig. 1  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
TO ADJUST SEAT (See Fig. 2):  
TO INSTALL MOWER (See Figs. 4-12)  
Besuretractorisonlevelsurfaceandengageparkingbrake.  
•
Grasp adjustment handle(A) and pull up, slide seat to  
desired position and release adjustment handle.  
•
Lower attachment lift lever to it's lowest position.  
CAUTION: Lift lever is spring loaded.  
Have a tight grip on lift lever, lower it  
slowly and engage in lowest position.  
•
Turn steering wheel to the left as far as it will go and  
position mower on right side of tractor with deflector  
shield to the right.  
A
Fig. 2  
NOTE:Youmaynowrollyourtractorofftheskid. Followthe  
instructions below to remove the tractor from the skid.  
02965  
WARNING:Beforestarting,read,understandandfollow  
all instructions in the Operation section of this manual. Be  
sure tractor is in a well-ventilated area. Be sure the area in  
front of tractor is clear of other people and objects.  
Fig. 4  
NOTE:Besuremowersidesuspensionarms(A)arepointing  
forward before sliding mower under tractor.  
•
Slide mower under tractor until it is centered under  
tractor.  
TOROLLTRACTOROFFSKID (SeeOperation  
section for location and function of controls)  
•
•
•
Raise attachment lift lever to its highest position.  
Releaseparkingbrakebydepressingclutch/brakepedal.  
Place freewheel control in "transmission disengaged"  
position (See “TO TRANSPORT” in the Operation  
section of this manual).  
•
Roll tractor forward off skid.  
Continue with the instructions that follow.  
ASSEMBLE FRONT WHEEL TO MOWER  
(See Fig. 3)  
A
•
Using shoulder bolt, washer and locknut from parts  
bag,assemblefrontwheeltomowerasshown.Tighten  
securely.  
Fig. 5  
•
FIRST INSTALL ANTI-SWAY BAR (S).  
•
From right side of mower, insert anti-sway bar into  
hole in transmission bracket (T).  
S
T
A
Fig. 3  
Fig. 6  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
•
•
Pivot bar towards you and insert other end of bar  
into hole in rear mower bracket (D). Move mower  
A
as needed to insert bar.  
Secure with washer and retainer spring as shown  
D
B
Fig. 8  
•
•
ATTACH REAR LIFT LINKS (C) - Lift rear corner of  
mower and position slot in link assembly over pin on  
rear mower bracket (D) and secure with washer and  
retainer spring.  
Repeat on opposite side of tractor.  
Fig. 7  
C
•
•
ATTACH MOWER SIDE SUSPENSION ARMS (A) TO  
CHASSIS - Position hole in arm over pin (B) on outside  
of tractor chassis and secure with washer and retainer  
spring.  
D
Repeat on opposite side of tractor.  
Fig. 9  
L
B
M
F
K
A
E
H
S
C
C
D
D
Fig. 10  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
•
•
Turnsteeringwheeltopositionwheelsstraightforward.  
CHECK FOR PROPER POSITION OF ALL  
ATTACH FRONT LINK (E) - Work from left side of trac-  
tor. Insert rod end of link assembly through front hole  
in tractor front suspension bracket (F) and secure with  
retainer spring (G) through hole in link located behind  
the bracket.  
Insertotherendoflink(E)intoholeinfrontmowerbracket  
(H) and secure with washer and retainer spring (J).  
BELTS  
See the Fig. ures that are shown for replacing motion and  
mower blade drive belts in the Service and Adjustments  
section of this manual. Verify that the belts are routed  
correctly.  
•
•
CHECK BRAKE SYSTEM  
Afteryoulearnhowtooperateyourtractor,checktoseethat  
the brake is operating properly. See “TO CHECK BRAKE”  
in the Service and Adjustments section of this manual.  
Disengagebelttensionrod(K)fromlockingbracket(L).  
E
H
J
✓CHECKLIST  
BEFORE YOU OPERATE YOUR NEW TRACTOR, WE  
WISH TO ASSURE THAT YOU RECEIVE THE BEST  
PERFORMANCE AND SATISFACTION FROM THIS  
QUALITY PRODUCT.  
F
G
PLEASE REVIEW THE FOLLOWING CHECKLIST:  
✓ All assembly instructions have been completed.  
✓ No remaining loose parts in carton.  
Fig. 11  
•
Install belt onto engine clutch pulley (M).  
✓ Battery is properly prepared and charged.  
✓ Seat is adjusted comfortably and tightened securely.  
M
✓ All tires are properly inflated. (For shipping purposes,  
the tires were overinflated at the factory).  
✓ Be sure mower deck is properly leveled side-to-side/  
front-to-rear for best cutting results. (Tires must be  
properly inflated for leveling).  
✓ Check mower and drive belts. Be sure they are routed  
Fig. 12  
properly around pulleys and inside all belt keepers.  
IMPORTANT: Check belt for proper routing in all mower  
pulley grooves.  
•
✓ Check wiring. See that all connections are still secure  
Engage belt tension rod (K) on locking bracket (L).  
and wires are properly clamped.  
✓ Before driving tractor, be sure freewheel control is in  
“transmission engaged” position (see “TO TRANS-  
PORT” in the Operation section of this manual).  
CAUTION: Belt tension rod is spring  
loaded. Have a tight grip on rod and  
engage slowly.  
WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY  
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT  
ITEMS:  
•
•
Raise attachment lift lever to highest position.  
If necessary, adjust gauge wheels before operating  
mower as shown in the Operation section of this  
manual.  
✓ Engine oil is at proper level.  
✓ Fuel tank is filled with fresh, clean, regular unleaded  
MOWER DRIVE BELT INSTALLATION  
gasoline.  
Follow procedure described in “TO REPLACE MOWER  
BLADE DRIVE BELT ” in the "Service and Adjustments"  
section of this manual.  
✓ Become familiar with all controls, their location and  
function. Operate them before you start the engine.  
CHECK TIRE PRESSURE  
The tires on your tractor were overinflated at the factory  
for shipping purposes. Correct tire pressure is important  
for best cutting performance.  
✓ Be sure brake system is in safe operating condition.  
✓ Be sure Operator Presence System and Reverse Op-  
eration System (ROS) are working properly (See the  
Operation and Maintenance sections in this manual).  
•
Reduce tire pressure to PSI shown on tires.  
✓ It is important to purge the transmission before op-  
erating your tractor for the first time. Follow proper  
starting and transmission purging instructions (See  
“TOSTARTENGINE”and“PURGETRANSMISSION”  
in the Operation section of this manual).  
CHECK DECK LEVELNESS  
For best cutting results, mower housing should be prop-  
erly leveled. See “TO LEVEL MOWER HOUSING” in the  
Service and Adjustments section of this manual.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.  
FAST  
SLOW  
REVERSE  
HIGH  
LOW  
NEUTRAL  
CHOKE  
IGNITION SWITCH  
MOWER LIFT  
ENGINE START  
MOWER HEIGHT  
ENGINE ON  
PARKING BRAKE  
REVERSE  
OPERATION  
SYSTEM (ROS)  
ENGINE OFF  
CLUTCH/BRAKE  
PEDAL  
LIGHTS ON  
CRUISE CONTROL  
BATTERY  
REVERSE  
FUEL  
FORWARD  
15  
15  
ATTACHMENT  
CLUTCH ENGAGED  
DANGER, KEEP HANDS  
AND FEET AWAY  
ATTACHMENT  
CLUTCH DISENGAGED  
SLOPE HAZARDS  
KEEP AREA CLEAR  
(SEE SAFETY RULES SECTION)  
DANGER indicates a hazard which, if not avoided,  
will result in death or serious injury.  
WARNING indicates a hazard which, if not avoided,  
could result in death or serious injury.  
FREE WHEEL  
(Automatic Models only)  
CAUTION indicates a hazard which, if not avoided,  
might result in minor or moderate injury.  
CAUTION when used without the alert symbol,  
indicates a situation that could result in damage  
to the tractor and/or engine.  
Failure to follow instructions  
could result in serious injury or  
death. The safety alert symbol  
is used to identify safety inform-  
ation about hazards which can  
result in death, serious injury  
and/or property damage.  
HOT SURFACES indicates a hazard which,  
if not avoided, could result in death, serious injury  
and/or property damage.  
FIRE indicates a hazard which, if not avoided,  
could result in death, serious injury and/or  
property damage.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOW YOUR TRACTOR  
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR  
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.  
Save this manual for future reference.  
D
H
P
G
E
N
F
B
Q
A
C
J
M
Fig. 13  
Our tractors conform to the applicable safety standards of the American National Standards Institute.  
(A) ATTACHMENT LIFT LEVER - Used to raise and lower  
(G) REVERSE OPERATION SYSTEM (ROS) "ON"  
POSITION - Allows operation of mower or other powered  
attachment while in reverse.  
the mower or other attachments mounted to your tractor.  
(B) BRAKE PEDAL - Used for braking the tractor and  
starting the engine.  
(H) LIGHT SWITCH - Turns the headlights on and off.  
(C) PARKING BRAKE - Locks clutch/brake pedal into the  
brake position.  
(J) MOTION CONTROL LEVER - Selects the speed and  
direction of the tractor.  
(D)THROTTLECONTROL-Usedtocontrolenginespeed.  
(M) FREEWHEEL CONTROL - Disengages transmission  
for pushing or slowly towing the tractor with the engine off.  
(E) ATTACHMENT CLUTCH SWITCH - Used to engage  
the mower blades, or other attachments mounted to your  
tractor.  
(N)CHOKECONTROL-Usedwhenstartingacoldengine.  
(P) SERVICE REMINDER/HOUR METER - Indicates  
when service is required for the engine and mower.  
(F) IGNITION SWITCH - Used for starting and stopping  
the engine.  
(Q)12-VOLTPOWERPORT-Usedfor12-voltaccessories.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The operation of any tractor can result in foreign objects thrown into the eyes, which can result  
in severe eye damage. Always wear safety glasses or eye shields while operating your tractor  
or performing any adjustments or repairs. We recommend standard safety glasses or a wide  
vision safety mask worn over spectacles.  
NOTE:Failuretomovethrottlecontrolbetweenhalfandfull  
HOW TO USE YOUR TRACTOR  
speed (fast) position, before stopping, may cause engine  
to “backfire”.  
TO SET PARKING BRAKE(See Fig. 14)  
•
Turn ignition key (F) to “STOP” position and remove  
key.Alwaysremovekeywhenleavingtractortoprevent  
unauthorized use.  
Your tractor is equipped with an operator presence sens-  
ing switch. When engine is running, any attempt by the  
operator to leave the seat without first setting the parking  
brake will shut off the engine.  
•
Never use the choke to stop the engine.  
•
•
Depress brake pedal (B) all the way down and hold.  
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY  
POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY  
TO DISCHARGE AND GO DEAD.  
Pull parking brake lever (C) up and hold, release pres-  
sure from brake pedal (B), then release parking brake  
lever. Pedal should remain in brake position. Make  
sure parking brake will hold tractor secure.  
NOTE: Under certain conditions when tractor is standing  
idlewiththeenginerunning, hotengineexhaustgasesmay  
cause “browning” of grass. To eliminate this possibility, al-  
ways stop engine when stopping tractor on grass areas.  
C
CAUTION: Always stop tractor com-  
pletely, as described above, and set  
parkingbrakebeforeleavingtheopera-  
tor's position.  
B
TO USE THROTTLE CONTROL (See Fig. 16)  
Always operate engine at full speed (fast).  
Fig. 14  
•
Operating engine at less than full speed (fast) reduces  
engines operating efficiency.  
STOPPING (See Fig. X)  
•
Full speed (fast) offers the best bagging and mower  
performance.  
MOWER BLADES -  
•
To stop mower blades, place attachment clutch control  
in the “DISENGAGED” position ( ).  
D
N
(
) ATTACHMENT  
CLUTCH SWITCH  
“DISENGAGED”  
(
) ATTACHMENT  
CLUTCH SWITCH  
“ENGAGED”  
F
Fig. 16  
Fig. 15  
TO USE CHOKE CONTROL (See Fig. 16)  
GROUND DRIVE -  
Usechokecontrolwheneveryouarestartingacoldengine.  
•
To stop ground drive, depress brake pedal all the way  
down.  
Do not use to start a warm engine.  
•
To engage choke control, pull knob out. Slowly push  
knob in to disengage.  
•
Move motion control lever (J) to neutral position.  
ENGINE -  
Move throttle control (D) between half and full speed  
(fast) position.  
•
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO MOVE FORWARD AND BACKWARD  
TO ADJUST GAUGE WHEELS (See Fig. 19)  
(See Fig. 17)  
Gaugewheels areproperlyadjustedwhentheyareslightly  
offthegroundwhenmowerisatthedesiredcuttingheightin  
operatingposition.Gaugewheelsthenkeepthedeckinprop-  
erpositiontohelppreventscalpinginmostterrainconditions.  
The direction and speed of movement is controlled by the  
motion control lever. (J)  
NOTE: Adjust gauge wheels with tractor on a flat level  
surface.  
J
•
Adjustmowertodesiredcuttingheight(See“TOADJUST  
MOWERCUTTINGHEIGHT”inthissectionofmanual).  
•
With mower in desired height of cut position, gauge  
wheels should be assembled so they are slightly off  
the ground. Install gauge wheel in appropriate hole.  
Tighten securely.  
•
Repeat for all, installing gauge wheel in same adjust-  
ment hole.  
Fig. 17  
•
•
•
Starttractorwithmotioncontrolleverinneutralposition.  
Release parking brake.  
Slowly move motion control lever to desired position.  
Fig. 19  
TO ADJUST MOWER CUTTING HEIGHT  
(See Fig. 18)  
TO OPERATE MOWER  
Your tractor isequipped withan operator presencesensing  
switch. Any attempt by the operator to leave the seat with  
the engine running and the attachment clutch engaged will  
shut off the engine. You must remain fully and centrally  
positioned in the seat to prevent the engine from hesitat-  
ing or cutting off when operating your equipment on rough,  
rolling terrain or hills.  
The position of the attachment lift lever (A) determines the  
cutting height.  
A
•
•
Select desired height of cut with attachment lift lever.  
Start mower blades by engaging attachment clutch  
control.  
TO STOP MOWER BLADES -  
•
disengage attachment clutch control.  
CAUTION:Donotoperatethemowerwithout  
either the entire grass catcher, on mowers  
so equipped, or the deflector shield (S) in  
place (See Fig. 20).  
Fig. 18  
•
Put attachment lift lever in desired cutting height slot.  
The cutting height range is approximately 1" to 4". The  
heights are measured from the ground to the blade tip with  
the engine not running. These heights are approximate  
and may vary depending upon soil conditions, height of  
grass and types of grass being mowed.  
S
•
Theaveragelawnshouldbecuttoapproximately2-1/2  
inches during the cool season and to over 3 inches  
during hot months. For healthier and better looking  
lawns, mow often and after moderate growth.  
•
For best cutting performance, grass over 6 inches  
in height should be mowed twice. Make the first cut  
relatively high; the second to desired height.  
Fig. 20  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO TRANSPORT (See Fig. 13 and 21)  
REVERSE OPERATION SYSTEM (ROS)  
(See Fig. 22)  
When pushing or towing your tractor, be sure to disengage  
transmission by placing freewheel control in freewheeling  
position. Free wheel control is located at the rear drawbar  
of tractor.  
Your tractor is equipped with a Reverse Operation System  
(ROS). Any attempt by the operator to travel in the reverse  
direction with the attachment clutch engaged will shut off  
the engine unless ignition key is placed in the ROS "ON"  
position.  
•
Raiseattachmentlifttohighestpositionwithattachment  
lift control.  
•
Pull freewheel control out and down into the slot and  
release so it is held in the disengaged position.  
Do not push or tow tractor at more than two (2) MPH.  
To reengage transmission, reverse above procedure.  
WARNING: Backing up with the attachment clutch en-  
gaged while mowing is strongly discouraged. Turning the  
ROS "ON", to allow reverse operation with the attachment  
clutch engaged, should only be done when the operator  
decides it is necessary to reposition the machine with the  
attachment engaged. Do not mow in reverse unless  
absolutely necessary.  
•
•
NOTE: To protect hood from damage when transporting  
your tractor on a truck or a trailer, be sure hood is closed  
and secured to tractor. Use an appropriate means of tying  
hood to tractor (rope, cord, etc.).  
USING THE REVERSE OPERATION SYSTEM -  
Only use if you are certain no children or other bystanders  
will enter the mowing area.  
TRANSMISSION ENGAGED  
•
•
Move motion control lever to neutral (N) position.  
Withenginerunning,turnignitionkeycounterclockwise  
to ROS "ON" position.  
•
•
Look down and behind before and while backing.  
Slowly move motion control lever to reverse (R) posi-  
tion to start movement.  
•
When use of the ROS is no longer needed, turn the  
ignition key clockwise to engine "ON" position.  
TRANSMISSION DISENGAGED  
Fig. 21  
TOWING CARTS AND OTHER ATTACHMENTS  
Tow only the attachments that are recommended by and  
comply with specifications of the manufacturer of your trac-  
tor. Use common sense when towing. Too heavy of a load,  
while on a slope, is dangerous. Tires can lose traction with  
the ground and cause you to lose control of your tractor.  
ROS "ON"  
POSITION  
ENGINE "ON" POSITION  
(NORMAL OPERATING)  
Fig. 22  
TO OPERATE ON HILLS  
SERVICE REMINDER/HOUR METER  
CAUTION:Donotdriveupordownhills  
with slopes greater than 15° and do not  
drive across any slope.  
Serviceremindershowsthetotalnumberofhourstheengine  
has run and flashes to indicate that the engine or mower  
needs servicing. When service is required, the service  
reminder will flash for two hours. To service engine and  
mower, see the Maintenance section of this manual.  
•
Choose the slowest speed before starting up or down  
hills.  
NOTE: Service reminder runs when the ignition key is in  
any position but "STOP". For accurate reading, be sure key  
remainsinthe"STOP"positionwhenengineisnotrunning.  
•
•
Avoid stopping or changing speed on hills.  
If slowing is necessary, move throttle control lever to  
slower position.  
•
If stopping is absolutely necessary, push clutch/brake  
pedalquicklytobrakepositionandengageparkingbrake.  
•
Move motion control lever to neutral position.  
IMPORTANT: THE MOTION CONTROL LEVER DOES NOT  
RETURN TO NEUTRAL POSITION WHEN THE BRAKE PEDAL  
IS DEPRESSED.  
•
Torestartmovement, slowlyreleaseparkingbrakeand  
clutch/brake pedal.  
•
•
Slowly move motion control lever to slowest setting.  
Make all turns slowly.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO START ENGINE (See Fig. 13)  
BEFORE STARTING THE ENGINE  
When starting the engine for the first time or if the engine  
has run out of fuel, it will take extra cranking time to move  
fuel from the tank to the engine.  
CHECK ENGINE OIL LEVEL  
The engine in your tractor has been shipped, from the  
factory, already filled with summer weight oil.  
•
Besurefreewheelcontrolisinthetransmissionengaged  
position.  
•
•
Check engine oil with tractor on level ground.  
•
Sit on seat in operating position, depress brake pedal  
and set parking brake.  
Removeoilfillcap/dipstickandwipeclean, reinsert the  
dipstick and screw cap tight, wait for a few seconds,  
remove and read oil level. If necessary, add oil until  
“FULL” mark on dipstick is reached. Do not overfill.  
•
•
•
Move attachment clutch to “DISENGAGED” position.  
Move throttle control to fast position  
Pull choke control out for a cold engine start attempt.  
For a warm engine start attempt the choke control may  
not be needed.  
•
•
For cold weather operation you should change oil for  
easier starting (See “OIL VISCOSITY CHART” in the  
Maintenance section of this manual).  
To change engine oil, see the Maintenance section in  
this manual.  
NOTE: Before starting, read the warm and cold starting  
procedures below.  
•
Insert key into ignition and turn key clockwise to  
“START” position and release key as soon as engine  
starts. Do not run starter continuously for more than  
fifteen seconds per minute. If the engine does not start  
after several attempts, push choke control in, wait a  
few minutes and try again. If engine still does not start,  
pull the choke control out and retry.  
ADD GASOLINE  
•
Fill fuel tank to bottom of filler neck. Do not overfill. Use  
fresh,clean,regularunleadedgasolinewithaminimumof  
87 octane. (Use of leaded gasoline will increase carbon  
and lead oxide deposits and reduce valve life). Do not  
mix oil with gasoline. Purchase fuel in quantities that can  
be used within 30 days to assure fuel freshness.  
WARM WEATHER STARTING (50° F and above)  
•
When engine starts, slowly push choke control in until  
theenginebeginstorunsmoothly.Iftheenginestartsto  
run roughly, pull the choke control out slightly for a few  
secondsandthencontinuetopushthecontrolinslowly.  
CAUTION: Wipe off any spilled oil or  
fuel. Do not store, spill or use gasoline  
near an open flame.  
IMPORTANT: WHENOPERATINGINTEMPERATURESBELOW  
32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE  
TO HELP INSURE GOOD COLD WEATHER STARTING.  
•
The attachments and ground drive can now be used. If  
the engine does not accept the load, restart the engine  
and allow it to warm up for one minute using the choke  
as described above.  
CAUTION: Alcohol blended fuels (called gasohol  
or using ethanol or methanol) can attract moisture  
which leads to separation and formation of acids  
during storage. Acidic gas can damage the fuel  
systemofanenginewhileinstorage. Toavoidengine  
problems, the fuel system should be emptied before  
storage of 30 days or longer. Drain the gas tank,  
start the engine and let it run until the fuel lines and  
carburetor are empty. Use fresh fuel next season.  
See Storage Instructions for additional information.  
Never use engine or carburetor cleaner products in  
the fuel tank or permanent damage may occur.  
COLD WEATHER STARTING (50° F and below)  
•
When engine starts, slowly push choke control in until  
the engine begins to run smoothly. Continue to push  
the choke control in small steps allowing the engine to  
acceptsmallchangesinspeedandload,untilthechoke  
control is fully in. If the engine starts to run roughly, pull  
the choke control out slightly for a few seconds and  
then continue to push the control in slowly. This may  
requireanenginewarm-upperiodfromseveralseconds  
to several minutes, depending on the temperature.  
AUTOMATIC TRANSMISSION WARM UP  
•
Beforedrivingtheunitincoldweather,thetransmission  
should be warmed up as follows:  
•
•
Be sure the tractor is on level ground.  
Release the parking brake and let the brake slowly  
return to operating position.  
•
Allowoneminutefortransmissiontowarmup.This  
can be done during the engine warm up period.  
•
The attachments can be used during the engine warm-  
up period after the transmission has been warmed up  
andmayrequirethechokecontrolbepulledoutslightly.  
NOTE: If at a high altitude (above 3000 feet) or in cold  
temperatures (below 32 F) the carburetor fuel mixture may  
need to be adjusted for best engine performance. See “TO  
ADJUST CARBURETOR” in the Service and Adjustments  
section of this manual.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
PURGE TRANSMISSION  
MOWING TIPS  
•
Mower should be properly leveled for best mowing  
performance. See “TO LEVEL MOWER HOUSING” in  
the Service and Adjustments section of this manual.  
CAUTION: Never engage or disengage  
freewheelleverwhiletheengineisrunning.  
•
•
The left hand side of mower should be used for  
trimming.  
To ensure proper operation and performance, it is recom-  
mended that the transmission be purged before operating  
tractor for the first time. This procedure will remove any  
trapped air inside the transmission which may have devel-  
oped during shipping of your tractor.  
IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE  
REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD  
BEPURGEDAFTERREINSTALLATIONBEFOREOPERATING  
THE TRACTOR.  
Drive so that clippings are discharged onto the area  
that has been cut. Have the cut area to the right of the  
machine. This will result in a more even distribution of  
clippings and more uniform cutting.  
•
When mowing large areas, start by turning to the right  
so that clippings will discharge away from shrubs,  
fences, driveways, etc. After one or two rounds, mow  
in the opposite direction making left hand turns until  
finished (See Fig. 23).  
1. Place tractor safely on a level surface - that is clear  
and open - with engine off and parking brake set.  
2. Disengage transmission by placing freewheel control  
in freewheeling position (See “TO TRANSPORT” in  
this section of manual).  
3. Sitting in the tractor seat, start engine. After the engine  
is running, move throttle control to slow position. With  
motioncontrolleverinneutralposition,slowlydisengage  
clutch/brake pedal.  
CAUTION: Atanytime,duringstep4,there  
may be movement of the drive wheels.  
Fig. 23  
•
If grass is extremely tall, it should be mowed twice to  
reduce load and possible fire hazard from dried clip-  
pings. Make first cut relatively high; the second to the  
desired height.  
Do not mow grass when it is wet. Wet grass will plug  
mower and leave undesirable clumps. Allow grass to  
dry before mowing.  
Always operate engine at full throttle when mow-  
ing to assure better mowing performance and proper  
discharge of material. Regulate ground speed by  
selecting a low enough gear to give the mower cutting  
performance as well as the quality of cut desired.  
When operating attachments, select a ground speed  
that will suit the terrain and give best performance of  
the attachment being used.  
4. Move motion control lever to full forward position and  
hold for five (5) seconds. Move lever to full reverse  
position and hold for five (5) seconds. Repeat this  
procedure three (3) times.  
5. Move motion control lever to neutral position. Shut- off  
engine and set parking brake.  
6. Engage transmission by placing freewheel control in  
engaged position (See “TO TRANSPORT” in this sec-  
tion of manual).  
7. Sitting in the tractor seat, start engine. After the engine  
is running, move throttle control to half (1/2) speed.  
With motion control lever in neutral position, slowly  
disengage clutch/brake pedal.  
8. Slowly move motion control lever forward, after the  
tractor moves approximately five (5) feet, slowly move  
motion control lever to reverse position. After the trac-  
tor moves approximately five (5) feet return the motion  
control lever to the neutral position. Repeat this proce-  
dure with the motion control lever three (3) times.  
•
•
•
Your transmission is now purged and now ready for normal  
operation.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
BEFORE  
EACH  
USE  
EVERY  
8
HOURS  
EVERY  
25  
HOURS  
EVERY  
50  
HOURS  
EVERY  
100  
HOURS  
EVERY  
SEASON  
BEFORE  
STORAGE  
MAINTENANCE  
SCHEDULE  
Check Brake Operation  
T Check Tire Pressure  
R Check Operator Presence & ROS Systems  
A Check for Loose Fasteners  
Check/Replace Mower Blades  
3
4
C
T
0
Lubrication Chart  
Check Battery Level  
Clean Battery and Terminals  
Check Transaxle Cooling  
Check Mower Levelness  
Check V-Belts  
R
Check Engine Oil Level  
1,2  
Change Engine Oil (with oil filter)  
1,2  
E Change Engine Oil (without oil filter)  
N Clean Air Filter  
2
2
G Clean Air Screen  
Inspect Muffler/Spark Arrester  
I
N
1,  
2
2
Replace Oil Filter (If equipped)  
E Clean Engine Cooling Fins  
Replace Spark Plug  
Replace Air Filter Paper Cartridge  
Replace Fuel Filter  
2
1 - Change more often when operating under a heavy load or  
in high ambient temperatures.  
3 - Replace blades more often when mowing in sandy soil.  
4 - Not required if equipped with maintenance-free battery.  
2 - Service more often when operating in dirty or dusty conditions.  
LUBRICATION CHART  
GENERAL RECOMMENDATIONS  
The warranty on this tractor does not cover items that have  
beensubjectedtooperatorabuseornegligence. Toreceive  
full value from the warranty, operator must maintain tractor  
as instructed in this manual.  
SPINDLE ZERK  
SPINDLE ZERK  
➀
➀
➀
FRONT  
WHEEL  
BEARING  
ZERK  
➀
FRONT  
WHEEL  
BEARING  
ZERK  
Some adjustments will need to be made periodically to  
properly maintain your tractor.  
At least once a season, check to see if you should make  
any of the adjustments described in the Service and  
Adjustments section of this manual.  
STEERING  
SECTOR  
GEAR  
➀
ENGINE  
➁
•
At least once a year you should replace the spark plug,  
clean or replace air filter, and check blades and belts  
for wear. A new spark plug and clean air filter assure  
proper air-fuel mixture and help your engine run better  
and last longer.  
TEETH  
BEFORE EACH USE  
01965  
•
•
•
•
Check engine oil level.  
Check brake operation.  
Check tire pressure.  
Check operator presence and ROS systems for proper  
operation.  
General Purpose Grease  
➀
➁
Refer to Maintenance “ENGINE” Section  
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS  
WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS  
LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL  
SHORTENTHELIFEOFTHESELF-LUBRICATINGBEARINGS.  
IFYOUFEELTHEYMUSTBELUBRICATED, USEONLYADRY,  
POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY.  
•
Check for loose fasteners.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
BLADE CARE  
Forbestresultsmowerbladesmustbekeptsharp. Replace  
bent or damaged blades.  
TRACTOR  
Always observe safety rules when performing any  
maintenance.  
CAUTION:Useonlyareplacementbladeap-  
provedbythemanufacturerofyourtractor.  
Using a blade not approved by the manu-  
facturer of your tractor is hazardous, could  
damageyourtractorandvoidyourwarranty.  
BRAKE OPERATION  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be checked and adjusted. (See  
“TO CHECK BRAKE” in the Service and Adjustments  
section of this manual).  
BLADE REMOVAL (See Fig. 25)  
TIRES  
•
Raisemowertohighestpositiontoallowaccesstoblades.  
•
•
•
Maintain proper air pressure in all tires (See the sides  
of tires for proper PSI).  
Keep tires free of gasoline, oil, or insect control  
chemicals which can harm rubber.  
Avoid stumps, stones, deep ruts, sharp objects and  
other hazards that may cause tire damage.  
NOTE: Protect your hands with gloves and/or wrap blade  
with heavy cloth.  
•
•
Remove blade bolt by turning counterclockwise.  
Install new or resharpened blade with stamped "THIS  
SIDE UP" facing deck and mandrel assembly.  
IMPORTANT:TOENSUREPROPERASSEMBLY,CENTERHOLE  
INBLADEMUSTALIGNWITHSTARONMANDRELASSEMBLY.  
NOTE: To seal tire punctures and prevent flat tires due  
to slow leaks, tire sealant may be purchased from your  
local parts dealer. Tire sealant also prevents tire dry rot  
and corrosion.  
•
Install and tighten blade bolt securely (45-55 Ft. Lbs.  
torque).  
IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.  
OPERATOR PRESENCE SYSTEM AND REVERSE  
OPERATION SYSTEM (ROS) (See Fig. 24)  
Be sure operator presence and reverse operation systems  
are working properly. If your tractor does not function as  
described, repair the problem immediately.  
MANDREL ASSEMBLY  
BLADE  
•
The engine should not start unless the brake pedal is  
fully depressed, and the attachment clutch control is  
in the disengaged position.  
BLADE BOLT  
STAR  
(SPECIAL)  
CHECK OPERATOR PRESENCE SYSTEM  
•
•
•
Whentheengineisrunning,anyattemptbytheoperator  
to leave the seat without first setting the parking brake  
should shut off the engine.  
When the engine is running and the attachment clutch  
is engaged, any attempt by the operator to leave the  
seat should shut off the engine.  
CENTER HOLE  
Fig. 25  
BATTERY  
Yourtractorhasabatterychargingsystemwhichissufficient  
for normal use. However, periodic charging of the battery  
with an automotive charger will extend its life.  
The attachment clutch should never operate unless  
the operator is in the seat.  
•
•
•
•
Keep battery and terminals clean.  
Keep battery bolts tight.  
Keep small vent holes open.  
Recharge at 6-10 amperes for 1 hour.  
CHECK REVERSE OPERATION (ROS) SYSTEM  
•
When the engine is running with the ignition switch in  
the engine "ON" position and the attachment clutch  
engaged, any attempt by the operator to shift into  
reverse should shut off the engine.  
NOTE:Theoriginalequipmentbatteryonyourtractorismain-  
tenancefree.Donotattempttoopenorremovecapsorcov-  
ers.Addingorcheckinglevelofelectrolyteisnotnecessary.  
•
When the engine is running with the ignition switch  
in the ROS "ON" position and the attachment clutch  
engaged, any attempt by the operator to shift into  
reverse should NOT shut off the engine.  
TO CLEAN BATTERY AND TERMINALS  
Corrosion and dirt on the battery and terminals can cause  
the battery to “leak” power.  
•
•
Raise seat/hood.  
Disconnect BLACK battery cable first then RED bat-  
tery cable and remove battery from tractor.  
•
•
Rinse the battery with plain water and dry.  
Cleanterminalsandbattery cableends withwirebrush  
until bright.  
ROS "ON"  
POSITION  
ENGINE "ON" POSITION  
(NORMAL OPERATING)  
•
•
Coat terminals with grease or petroleum jelly.  
Reinstall battery (See “REPLACING BATTERY" in the  
SERVICEANDADJUSTMENTSsectionofthismanual).  
Fig. 24  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
DECK WASHOUT PORT (See Fig. 26)  
TRANSAXLE MAINTENANCE  
Your tractor’s deck is equipped with a washout port on  
its surface as part of its deck wash system. It should be  
utilized after each use.  
The transmission fan and cooling fins should be kept clean  
to assure proper cooling.  
Do not attempt to clean fan or transmission while engine  
is running or while the transmission is hot. To prevent pos-  
sible damage to seals, do not use high pressure water or  
steam to clean transmission.  
1. Drivethetractortoalevel,clearspotonyourlawn,near  
enoughtoawaterspigotforyourgardenhosetoreach.  
IMPORTANT:Makecertainthetractor’sdischargechuteis  
directed AWAY from your house, garage, parked cars, etc.  
Remove bagger chute or mulch cover if attached.  
•
Inspect cooling fan to be sure fan blades are intact and  
clean.  
2. Make sure the PTO (Blade Engage) is not engaged,  
set the parking brake, and stop the engine.  
•
Inspect cooling fins for dirt, grass clippings and other  
materials. To prevent damage to seals, do not use  
compressed air or high pressure sprayer to clean  
cooling fins.  
3. Threadthenozzleadapter(packagedwithyourtractor’s  
Operator’s Manual) onto the end of your garden hose.  
4. Pull back the lock collar of the nozzle adapter and push  
the adapter onto the deck washout port at the left end  
of the mower deck. Release the lock collar to lock the  
adapter on the nozzle.  
TRANSAXLE PUMP FLUID  
The transaxle was sealed at the factory and fluid mainte-  
nance is not required for the life of the transaxle. Should  
the transaxle ever leak or require servicing, contact your  
nearest authorized service center/department.  
HOSE  
NOZZLE ADAPTER  
V-BELTS  
WASHOUT  
PORT  
Check V-belts for deterioration and wear after 100 hours  
of operation and replace if necessary. The belts are not  
adjustable. Replace belts if they begin to slip from wear.  
ENGINE  
LUBRICATION  
Only use high quality detergent oil rated with API service  
classification SG-SL. Select the oil’s SAE viscosity grade  
according to your expected operating temperature.  
SAE VISCOSITY GRADES  
Fig. 26  
10W30  
IMPORTANT: Tug hose ensuring connection is secure.  
5W-30  
5. Turn the water on.  
-20  
0
30  
32 40  
0
100  
60  
80  
F
6. While sitting in the operator’s position on the tractor,  
re-start the engine and place the throttle lever in the  
Fast " " position.  
C
-20  
10  
-30  
-10  
20  
30  
40  
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE  
IMPORTANT: Recheck the area making certain the area  
Change the oil after every 50 hours of operation or at least  
onceayearifthetractorisnotusedfor50hoursinoneyear.  
is clear.  
7. Move the tractor’s PTO (Blade Engage) to the ON  
position. Remain in the operator’s position with the  
cutting deck engaged until the deck is cleaned.  
Check the crankcase oil level before starting the engine  
and after each eight (8) hours of operation.  
8. Move the tractor’s PTO (Blade Engage) to the OFF  
position. Turn the ignition key to the STOP position to  
turn the tractor’s engine off. Turn the water off.  
9. Pull back the lock collar of the nozzle adapter to dis-  
connect the adapter from the nozzle washout port.  
10. Move the tractor to a dry area, preferably a concrete or  
pavedarea.EngagethemowerdeckPTOtoremoveex-  
cesswaterandtohelpdrybeforeputtingthetractoraway.  
ENGINE OIL FILTER  
Replace the engine oil filter every season or every other  
oil change if the tractor is used more than 100 hours in  
one year.  
WARNING: A broken or missing washout  
fitting could expose you or others to  
thrownobjectsfromcontactwiththeblade.  
•
•
Replace broken or missing washout fitting  
immediately, prior to using mower again.  
Pluganyholesinmowerwithboltsandlocknuts.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
TO CHANGE ENGINE OIL (See Fig. 27)  
Determine temperature range expected before oil change.  
All oil must meet API service classification SG-SL.  
AIR FILTER  
Your engine will not run properly using a dirty air filter.  
Service air cleaner more often under dusty conditions.  
See Engine Manual.  
•
•
•
•
Be sure tractor is on level surface.  
Oil will drain more freely when warm.  
Catch oil in a suitable container.  
Remove oil fill cap/dipstick. Be careful not to allow dirt  
to enter the engine when changing oil.  
CLEAN AIR SCREEN  
Air screen must be kept free of dirt and chaff to prevent  
enginedamagefromoverheating. Cleanwithawirebrushor  
compressedairtoremovedirtandstubborndriedgumfibers.  
•
Remove yellow cap from end of drain valve and install  
the drain tube onto the fitting.  
MUFFLER  
Inspect and replace corroded muffler and spark arrester (if  
equipped) as it could create a fire hazard and/or damage.  
OIL DRAIN VALVE  
SPARK PLUGS  
Replace spark plugs at the beginning of each mowing  
season or after every 100 hours of operation, whichever  
occurs first. Spark plug type and gap setting are shown in  
“PRODUCT SPECIFICATIONS” section of this manual.  
CLOSED  
AND  
LOCKED  
POSITION  
IN-LINE FUEL FILTER (See Fig. 28)  
The fuel filter should be replaced once each season. If fuel  
filter becomes clogged, obstructing fuel flow to carburetor,  
replacement is required.  
YELLOW  
CAP  
DRAIN  
TUBE  
•
•
Withenginecool,removefilterandplugfuellinesections.  
Place new fuel filter in position in fuel line with arrow  
pointing towards carburetor.  
Fig. 27  
•
•
Be sure there are no fuel line leaks and clamps are  
properly positioned.  
Immediately wipe up any spilled gasoline.  
•
Unlock drain valve by pushing inward and turning  
counterclockwise.  
To open, pull out on the drain valve.  
•
•
After oil has drained completely, close and lock the  
drain valve by pushing inward and turning clockwise  
until the pin is in the locked position as shown.  
CLAMP  
CLAMP  
•
•
Remove the drain tube and replace the cap onto to the  
bottom fitting of the drain valve.  
Refill engine with oil through oil fill dipstick tube. Pour  
slowly. Do not overfill. For approximate capacity  
see “PRODUCT SPECIFICATIONS” section of this  
manual.  
FUEL FILTER  
Fig. 28  
CLEANING  
•
Use gauge on oil fill cap/dipstick for checking level.  
Insert dipstick into the tube and rest the oil fill cap on  
the tube. Do not thread the cap onto the tube when  
taking reading. Keep oil at “FULL” line on dipstick.  
Tighten cap onto the tube securely when finished.  
•
•
Cleanengine,battery,seat,finish,etc.ofallforeignmatter.  
Keep finished surfaces and wheels free of all gasoline,  
oil, etc.  
•
Protect painted surfaces with automotive type wax.  
ENGINE COOLING SYSTEM  
To insure proper cooling, make sure the grass screen,  
cooling fins, and other external surfaces of the engine are  
kept clean at all times.  
We do not recommend using a garden hose or pressure  
washer to clean your tractor unless the engine and trans-  
mission are covered to keep water out. Water in engine or  
transmission will shorten the useful life of your tractor. Use  
compressed air or a leaf blower to remove grass, leaves  
and trash from tractor and mower.  
Every 100 hours of operation (more often under extremely  
dusty, dirty conditions), remove the blower housing and  
other cooling shrouds. Clean the cooling fins and external  
surfaces as necessary. Make sure the cooling shrouds  
are reinstalled.  
NOTE: Operating the engine with a blocked grass screen,  
dirtyorpluggedcoolingfins,and/orcoolingshroudsremoved  
will cause engine damage due to overheating.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:  
• Depress brake pedal fully and set parking brake.  
• Place attachment clutch in “DISENGAGED” position.  
• Turn ignition key to “STOP” and remove key.  
• Make sure the blades and all moving parts have completely stopped.  
• Disconnectsparkplugwirefromsparkplugandplacewirewhereitcannotcomeincontact withplug.  
TO REMOVE MOWER (See Fig. 29)  
TO LEVEL MOWER  
Make sure tires are properly inflated to the PSI shown on  
tires. If tires are over or under inflated, it may affect the  
appearance of your lawn and lead you to think the mower  
is not adjusted properly.  
•
•
•
Place attachment clutch in “DISENGAGED” position.  
Lower attachment lift lever to its lowest position.  
Disengage belt tension rod (K) from lock bracket (L).  
VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 30)  
CAUTION: Belt tension rod is spring  
loaded. Have a tight grip on rod and  
release slowly.  
•
Withalltiresproperlyinflatedandifyourlawnappearsun-  
evenlycut,determinewhichsideofmoweriscuttinglower.  
NOTE: As desired, you can raise the low side of mower  
•
•
Remove mower belt from electric clutch pulley (M).  
Disconnect front link (E) from mower - remove retainer  
spring and washer.  
Gotoeithersideofmoweranddisconnectmowersuspen-  
sion arm (A) from chassis and rear lift link (C) from rear  
mowerbracket(D)-removeretainerspringsandwashers.  
Go to other side of mower and disconnect the suspen-  
sion arm and rear lift link.  
or lower the high side.  
•
•
Go to side of mower you wish to adjust.  
With a 3/4" or adjustable wrench, turn lift link adjust-  
ment nut (A) to the left to lower the mower, or, to the  
right to raise the mower.  
•
•
CAUTION: After rear lift links are discon-  
nected, the attachment lift lever will be  
spring loaded. Have a tight grip on lift  
leverwhenchangingpositionofthelever.  
A
•
From right side of mower, disconnect anti-sway bar (S)  
from right rear mower bracket (D) - remove retainer  
spring and washer and pull mower toward you until the  
bar falls from the hole in bracket.  
•
•
Turn tractor steering wheel to the left as far as it will go.  
Slide mower out from under right side of tractor.  
Turn nut right  
Turn nut left  
to raise mower  
to lower mower  
TO INSTALL MOWER  
Follow procedure described in “INSTALL MOWER AND  
DRIVE BELT” in the Assembly section of this manual.  
Fig. 30  
F
L
B
M
K
A
E
H
S
C
C
D
D
Fig. 29  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
NOTE: Each full turn of adjustment nut will change mower  
height about 3/16".  
•
Test your adjustment by mowing some uncut grass  
and visually checking the appearance. Readjust, if  
necessary, until you are satisfied with the results.  
B
A
PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 31)  
•
With all tires properly inflated, park tractor on level  
ground or driveway.  
CAUTION: Blades are sharp. Protect  
your hands with gloves and/or wrap  
blade with heavy cloth.  
LOOSEN  
ADJUST NUT  
B TO LOWER  
MOWER  
TIGHTEN ADJUST  
•
•
Raise mower to its highest position.  
NUT B TO RAISE  
MOWER  
At both sides of mower, position blade at side and  
measure the distance (A) from bottom edge of blade  
to the ground. The distance should be the same on  
both sides.  
LOOSEN JAM NUT A FIRST  
Fig. 33  
02966  
NOTE: Each full turn of the adjustment nut will change  
mower height about 1/8".  
•
•
Recheck measurements, adjust if necessary until front  
tip of blade is 1/8" to 1/2" lower than the rear tip.  
A
A
Holdadjustmentnutinpositionwithwrenchandtighten  
jam nut securely against adjustment nut.  
Fig. 31  
TO CHECK BRAKE  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be serviced.  
•
•
If adjustment is necessary, see steps in Visual Adjust-  
ment instructions above.  
Recheck measurements, adjust if necessary until both  
sides are equal.  
You may also check brake by:  
FRONT-TO-BACK ADJUSTMENT (See Fig. 32 and 33)  
IMPORTANT: Deck must be level side-to-side.  
To obtain the best cutting results, the mower blades should  
be adjusted so the front tip is 1/8" to 1/2" lower than the  
rear tip when the mower is in its highest position.  
•
Park tractor on a level, dry concrete or paved surface,  
depress brake pedal all the way down and engage  
parking brake.  
•
Disengage transmission by placing freewheel control  
in “transmission disengaged” position. Pull freewheel  
control out and into the slot and release so it is held in  
the disengaged position.  
CAUTION: Blades are sharp. Protect  
your hands with gloves and/or wrap  
blade with heavy cloth.  
The rear wheels must lock and skid when you try to manu-  
ally push the tractor forward. If the rear wheels rotate,  
then the brake needs to be serviced. Contact a qualified  
service center.  
•
•
Raise mower to highest position.  
Position any blade so the tip is pointing straight forward.  
Measure distance (B) to the ground at front and rear tip  
of the blade.  
TO ADJUST STEERING WHEEL ALIGNMENT  
•
•
•
If front tip of blade is not 1/8" to 1/2" lower than the rear  
If steering wheel crossbars are not horizontal (left to right)  
whenwheelsarepositionedstraightforward,removesteer-  
ing wheel and reassemble per instructions in the Assembly  
section of this manual.  
tip, go to the front of tractor.  
With an 11/16" or adjustable wrench, loosen jam nut A  
several turns to clear adjustment nut B.  
With a 3/4" or adjustable wrench, turn front link adjust-  
ment nut (B) clockwise (ltighten) to raise the front of  
mower, or, counterclockwise (loosen) to lower the front  
mower.  
FRONT WHEEL TOE-IN/CAMBER  
Your new tractor front wheel toe-in and camber is set at the  
factory and is normal. The front wheel toe-in and camber  
are not adjustable. If damage has occurred to affect the  
factory set front wheel toe-in or camber, contact a qualified  
service center.  
02548  
B
B
Fig. 32  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
BELT REMOVAL -  
TO REPLACE MOWER BLADE DRIVE BELT  
(See Fig. 34)  
1. Remove mower (See “TO REMOVE MOWER” section  
in this manual).  
MOWER DRIVE BELT REMOVAL  
NOTE: Observe entire motion drive belt and position of all  
•
•
•
Park tractor on a level surface. Engage parking brake.  
Lower attachment lift lever to its lowest position.  
Disengage belt tension rod (K) from lock bracket (L).  
belt guides and keepers.  
2. Disconnect clutch wire harness (A).  
3. Remove anti-rotation link (B) on right side of tractor.  
CAUTION: Belt tension rod is spring  
loaded. Have a firm grip on rod and  
release slowly.  
4. Remove belt from stationary idler (C) and clutching  
idler (D).  
5. Remove belt from centerspan idler (E).  
6. Pull belt slack toward rear of tractor. Carefully re-  
move belt upwards from transmission input pulley and  
over cooling fan blades (F).  
•
•
•
Remove screws (P) from mandrel covers (Q) and  
remove covers.  
Removeanydirtorgrassclippingswhichmayhaveaccu-  
mulatedaroundmandrelsandentireupperdecksurface.  
Remove belt from electric clutch pulley (M), both man-  
drel pulleys (R) and all idler pulleys (V).  
7. Remove belt downward from engine pulley and  
around electric clutch (G).  
8. Slide belt toward rear of tractor, off the steering plate  
(H) and remove from tractor.  
P
P
G
H
M
P
L
Q
Q
K
R
A
B
C
E
J
R
V
D
R
F
Fig. 34  
MOWER DRIVE BELT INSTALLATION  
02953  
electric  
•
Install belt around all mandrel pulleys (R) and around  
idler pulleys (V) as shown.  
Fig. 35  
•
Install belt onto electric clutch pulley (M).  
BELT INSTALLATION -  
IMPORTANT: Check belt for proper routing in all mower  
pulley grooves.  
•
•
1. Install new belt from tractor rear to front, over the steer-  
ing plate (H) and above clutch brake pedal shaft (J).  
Reassemble mandrel covers (Q). Securely tighten all  
screws.  
Engage belt tension rod (K) on locking bracket (L).  
2. Pull belt toward front of tractor and roll belt around  
electric clutch and onto engine pulley (G).  
3. Pull belt toward rear of tractor. Carefully work belt  
down around transmission cooling fan and onto the  
input pulley (F). Be sure belt is inside the belt keeper.  
4. Install belt on centerspan idler (E).  
5. Install belt through stationary idler (C) and clutching  
CAUTION: Belt tension rod is spring  
loaded. Have a tight grip on rod and  
engage slowly.  
idler (D).  
•
Raise attachment lift lever to highest position.  
6. Reinstall anti-rotation link (B) on right side of tractor.  
Tighten securely.  
7. Reconnect clutch harness (A).  
TO REPLACE MOTION DRIVE BELT  
(See Fig. 35)  
Park the tractor on level surface. Engage parking brake.  
For assistance, there is a belt installation guide decal on  
bottom side of left footrest.  
8. Make sure belt is in all pulley grooves and inside all  
belt guides and keepers.  
9. Install mower (See “TO INSTALL MOWER” section in  
this manual).  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REMOVE WHEEL (See Fig. 36)  
MOTION CONTROL  
LEVER  
NEUTRAL  
LOCK  
•
Block up axle securely.  
GATE  
•
Removeaxlecover,retainingringandwasherstoallow  
wheel removal (rear wheel contains a square key - Do  
not lose).  
•
•
Repair tire and reassemble.  
On rear wheels only: align grooves in rear wheel hub  
and axle. Insert square key.  
ADJUSTMENT  
BOLT  
FIG. 37  
•
Replace washers and snap retaining ring securely in  
axle groove.  
Replace axle cover.  
TO START ENGINE WITH A WEAK BATTERY  
(See Fig. 38)  
•
NOTE:Tosealtirepuncturesandpreventflattiresduetoslow  
leaks, tire sealant may be purchased from your local parts  
dealer. Tire sealant also prevents tire dry rot and corrosion.  
WARNING: Lead-acid batteries gen-  
erate explosive gases. Keep sparks,  
flameandsmokingmaterialsawayfrom  
batteries. Always wear eye protection  
when around batteries.  
WASHERS  
RETAINING  
RING  
If your battery is too weak to start the engine, it should be  
recharged. (See "BATTERY" in the MAINTENANCE sec-  
tion of this manual).  
AXLE  
COVER  
If “jumper cables” are used for emergency starting, follow  
this procedure:  
SQUARE KEY (REAR  
WHEEL ONLY)  
IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12  
VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12  
VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO  
START OTHER VEHICLES.  
Fig. 36  
TO ATTACH JUMPER CABLES -  
TRANSAXLE MOTION CONTROL LEVER  
NEUTRAL ADJUSTMENT (See Fig. 37)  
•
Connect one end of the RED cable to the POSITIVE  
(+) terminal of each battery(A-B), taking care not to  
short against tractor chassis.  
The motion control lever has been preset at the factory  
and adjustment should not be necessary.  
•
•
ConnectoneendoftheBLACKcabletotheNEGATIVE  
(-) terminal (C) of fully charged battery.  
Connect the other end of the BLACK cable (D) to good  
chassis ground, away from fuel tank and battery.  
•
•
•
•
•
•
Loosen adjustment bolt in front of the right rear wheel,  
and lightly tighten.  
Start engineandmove motion control leveruntil tractor  
does not move forward or backward.  
Holdmotioncontrolleverinthatpositionandturnengine  
off.  
While holding motion control lever in place, loosen the  
adjustment bolt.  
TO REMOVE CABLES, REVERSE ORDER -  
•
BLACK cable first from chassis and then from the fully  
charged battery.  
•
RED cable last from both batteries.  
Move motion control lever to the neutral (lock gate)  
position.  
Tighten adjustment bolt securely.  
NOTE: Ifadditionalclearanceisneededtogettoadjustment  
bolt, move mower deck height to the lowest position.  
After above adjustment is made, if the tractor still creeps  
forward or backward while motion control lever is in neutral  
position, follow these steps:  
WEAK OR DEAD  
BATTERY  
FULLY CHARGED  
BATTERY  
•
•
Loosen the adjustment bolt.  
Move the motion control lever 1/4 to 1/2 inch in the  
direction it is trying to creep.  
Fig. 38  
•
•
•
Tighten adjustment bolt securely.  
Start engine and test.  
If tractor still creeps, repeat above steps until satisfied.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
REPLACING BATTERY (See Fig. 39)  
TO REMOVE HOOD AND GRILL ASSEMBLY  
(See Fig. 40)  
WARNING: Do not short battery termi-  
nals by allowing a wrench or any other  
object to contact both terminals at the  
same time. Before connecting battery,  
remove metal bracelets, wristwatch  
bands, rings, etc. Positive terminal  
must be connected first to prevent  
sparking from accidental grounding.  
•
•
•
Raise hood.  
Unsnap headlight wire connector.  
Standinfrontoftractor. Grasphoodatsides, tilttoward  
engine and lift off of tractor.  
•
To replace, reverse above procedure.  
HOOD  
•
•
•
Lift hood to raised position.  
Remove terminal cover.  
Disconnect BLACK battery cable then RED battery  
cable and carefully remove battery from tractor.  
Install new battery with terminals in same position as  
old battery.  
HEADLIGHT  
WIRE  
CONNECTOR  
•
•
•
Reinstall terminal cover.  
First connect RED battery cable to positive (+) battery  
terminal with bolt and nut as shown. Tighten securely.  
02778  
•
•
ConnectBLACKgroundingcabletonegative(-)battery  
terminal with remaining bolt and nut. Tighten securely  
Close hood.  
Fig. 40  
NEGATIVE  
(BLACK)  
CABLE  
TRANSMISSION  
REMOVAL/REPLACEMENT  
TERMINAL  
COVER  
Should your transmission require removal for service or  
replacement, it should be purged after reinstallation and  
beforeoperatingthetractor. See“PURGETRANSMISSION”  
in the Operation section of this manual.  
ENGINE  
POSITIVE  
(RED)  
CABLE  
TO ADJUST THROTTLE CONTROL CABLE  
The throttle control has been preset at the factory and  
adjustment should not be necessary. If adjustment is nec-  
essary, see engine manual.  
Fig. 39  
TO ADJUST CHOKE CONTROL  
Thechokecontrolhasbeenpresetatthefactoryandadjust-  
ment should not be necessary. If adjustment is necessary,  
see engne manual.  
TO REPLACE HEADLIGHT BULB  
•
•
Raise hood.  
Pull bulb holder out of the hole in the backside of the  
grill.  
Replace bulb in holder and push bulb holder securely  
back into the hole in the backside of the grill.  
Close hood.  
•
•
TO ADJUST CARBURETOR  
Your carburetor is not adjustable. If your engine does not  
operate properly due to suspected carburetor problems,  
take your tractor to an authorized service center for repair  
and/or adjustment.  
INTERLOCKS AND RELAYS  
Loose or damaged wiring may cause your tractor to run  
poorly, stop running, or prevent it from starting.  
•
Check wiring. See electrical wiring diagram in the  
Repair Parts section.  
TO REPLACE FUSE  
Replace with 20 amp automotive-type plug-in fuse. The  
fuse holder is located behind the dash.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STORAGE  
Immediately prepare your tractor for storage at the end  
of the season or if the tractor will not be used for 30 days  
or more.  
ENGINE  
FUEL SYSTEM  
IMPORTANT: ITISIMPORTANTTOPREVENTGUMDEPOSITS  
FROMFORMINGINESSENTIALFUELSYSTEMPARTSSUCH  
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK  
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT  
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING  
ETHANOLORMETHANOL)CANATTRACTMOISTUREWHICH  
LEADSTOSEPARATIONANDFORMATIONOFACIDSDURING  
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM  
OF AN ENGINE WHILE IN STORAGE.  
WARNING: Neverstorethetractorwith  
gasoline in the tank inside a building  
where fumes may reach an open flame  
orspark. Allowtheenginetocoolbefore  
storing in any enclosure.  
TRACTOR  
•
•
•
Empty the fuel tank by starting the engine and let it run  
until the fuel lines and carburetor are empty.  
Never use engine or carburetor cleaner products in  
the fuel tank or permanent damage may occur.  
Remove mower from tractor for winter storage. When  
mower is to be stored for a period of time, clean it thor-  
oughly, remove all dirt, grease, leaves, etc. Store in a  
clean, dry area.  
Use fresh fuel next season.  
•
Clean entire tractor (See “CLEANING” in the Mainte-  
nance section of this manual).  
NOTE: Fuel stabilizer is an acceptable alternative in mini-  
mizing the formation of fuel gum deposits during storage.  
Add stabilizer to gasoline in fuel tank or storage container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to  
allow the stabilizer to reach the carburetor. Do not empty  
the gas tank and carburetor if using fuel stabilizer.  
•
Inspect and replace belts, if necessary (See belt re-  
placement instructions in the Service and Adjustments  
section of this manual).  
•
•
Lubricate as shown in the Maintenance section of this  
manual.  
Be sure that all nuts, bolts and screws are securely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
ENGINE OIL  
Drain oil (with engine warm) and replace with clean engine  
oil. (See “ENGINE” in the Maintenance section of this  
manual).  
•
Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
BATTERY  
CYLINDER(S)  
•
•
Fully charge the battery for storage.  
•
•
Remove spark plug(s).  
After a period of time in storage, battery may require  
recharging.  
Pour one ounce of oil through spark plug hole(s) into  
cylinder(s).  
•
To help prevent corrosion and power leakage during  
long periods of storage, battery cables should be dis-  
connected and battery cleaned thoroughly (see “TO  
CLEAN BATTERY AND TERMINALS” in the Mainte-  
nance section of this manual).  
After cleaning, leave cables disconnected and place  
cables where they cannot come in contact with battery  
terminals.  
•
•
Turn ignition key to “START” position for a few seconds  
to distribute oil.  
Replace with new spark plug(s).  
OTHER  
•
•
•
•
Do not store gasoline from one season to another.  
Replace your gasoline can if your can starts to rust.  
Rust and/or dirt in your gasoline will cause problems.  
If possible, store your tractor indoors and cover it to  
give protection from dust and dirt.  
Cover your tractor with a suitable protective cover that  
does not retain moisture. Do not use plastic. Plastic  
cannot breathe which allows condensation to form and  
will cause your tractor to rust.  
If battery is removed from tractor for storage, do not  
store battery directly on concrete or damp surfaces.  
•
•
IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE  
AND EXHAUST AREAS ARE STILL WARM.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
1. Out of fuel.  
1. Fill fuel tank.  
Will not start  
2. Engine not “CHOKED” properly.  
3. Engine flooded.  
4. Bad spark plug.  
5. Dirty air filter.  
2. See “TO START ENGINE” in Operation section.  
3. Wait several minutes before attempting to start.  
4. Replace spark plug.  
5. Clean/replace air filter.  
6. Dirty fuel filter.  
6. Replace fuel filter.  
7. Water in fuel.  
7. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
8. Loose or damaged wiring.  
8. Check all wiring.  
9. Carburetor out of adjustment.  
9. See “To Adjust Carburetor” in Service Adjustments  
section.  
10. Engine valves out of adjustment.  
10. Contact an authorized service center/department.  
1. Dirty air filter.  
2. Bad spark plug.  
1. Clean/replace air filter.  
2. Replace spark plug.  
Hard to start  
3. Weak or dead battery.  
4. Dirty fuel filter.  
3. Recharge or replace battery.  
4. Replace fuel filter.  
5. Stale or dirty fuel.  
6. Loose or damaged wiring.  
7. Carburetor out of adjustment.  
5. Empty fuel tank and refill tank with fresh, clean gas.  
6. Check all wiring.  
7. See “To Adjust Carburetor” in Service Adjustments  
section.  
8. Engine valves out of adjustment.  
8. Contact an authorized service center/department.  
1. Brake pedal not depressed.  
2. Attachment clutch is engaged.  
3. Weak or dead battery.  
1. Depress brake pedal.  
Engine will not  
turn over  
2. Disengage attachment clutch.  
3. Recharge or replace battery.  
4. Replace fuse.  
4. Blown fuse.  
5. Corroded battery terminals.  
6. Loose or damaged wiring.  
7. Faulty ignition switch.  
8. Faulty solenoid or starter.  
9. Faulty operator presence switch(es).  
5. Clean battery terminals.  
6. Check all wiring.  
7. Check/replace ignition switch.  
8. Check/replace solenoid or starter.  
9. Contact an authorized service center/department.  
1. Weak or dead battery.  
1. Recharge or replace battery.  
2. Clean battery terminals.  
3. Check all wiring.  
Engine clicks but  
will not start  
2. Corroded battery terminals.  
3. Loose or damaged wiring.  
4. Faulty solenoid or starter.  
4. Check/replace solenoid or starter.  
1. Cutting too much grass/too fast.  
2. Throttle in “CHOKE” position.  
1. Raise cutting height/reduce speed.  
2. Adjust throttle control.  
Loss of power  
3. Build-upofgrass,leaves,trashundermower. 3. Clean underside of mower housing.  
4. Dirty air filter.  
4. Clean/replace air filter.  
5. Low oil level/dirty oil.  
6. Faulty spark plug.  
7. Dirty fuel filter.  
5. Check oil level/change oil.  
6. Clean and regap or change spark plug.  
7. Replace fuel filter.  
8. Stale or dirty fuel.  
9. Water in fuel.  
8. Empty fuel tank and refill tank with fresh, clean gas.  
9. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
10. Spark plug wire loose.  
10. Connect and tighten spark plug wire.  
11. Dirty engine air screen/fins.  
12. Dirty/clogged muffler.  
11. Clean engine air screen/fins.  
12. Clean/replace muffler.  
13. Loose or damaged wiring.  
14. Carburetor out of adjustment.  
15. Engine valves out of adjustment.  
13. Check all wiring.  
14. See “To Adjust Carburetor” in Service Adjustments  
15. Contact an authorized service center/department.  
1. Worn, bent or loose blade.  
2. Bent blade mandrel.  
3. Loose/damaged part(s).  
1. Replace blade. Tighten blade bolt.  
2. Replace blade mandrel.  
3. Tighten loose part(s). Replace damaged parts.  
Excessive  
vibration  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
1. Faulty operator-safety presence control  
system.  
1. Check wiring, switches and connections. If not  
corrected, contact an authorized service center/  
department.  
Engine continues  
to run when oper-  
ator leaves seat  
with attachment  
clutch engaged  
1. Worn, bent or loose blade.  
2. Mower deck not level.  
1. Replace blade. Tighten blade bolt.  
2. Level mower deck.  
Poor cut - uneven  
3. Buildup of grass, leaves, trash under mower. 3. Clean underside of mower housing.  
4. Bent blade mandrel.  
4. Replace blade mandrel.  
5. Clogged mower deck vent holes from  
buildup of grass, leaves, and trash around  
mandrels.  
5. Clean around mandrels to open vent holes.  
1. Obstruction in clutch mechanism.  
2. Worn/damaged mower drive belt.  
3. Frozen idler pulley.  
1. Remove obstruction.  
2. Replace mower drive belt.  
3. Replace idler pulley.  
Mower blades will  
not rotate  
4. Frozen blade mandrel.  
4. Replace blade mandrel.  
1. Engine speed too slow.  
2. Travel speed too fast.  
3. Wet grass.  
4. Mower deck not level.  
5. Low/uneven tire air pressure.  
6. Worn, bent or loose blade.  
1. Place throttle control in “FAST” position.  
2. Shift to slower speed.  
3. Allow grass to dry before mowing.  
4. Level mower deck.  
5. Check tires for proper air pressure.  
6. Replace blade. Tighten blade bolt.  
Poor grass  
discharge  
7. Buildup of grass, leaves, trash under mower. 7. Clean underside of mower housing.  
8. Mower drive belt worn.  
9. Blades improperly installed.  
10. Improper blades used.  
8. Replace mower drive belt.  
9. Reinstall blades sharp edge down.  
10. Replace with blades listed in parts manual.  
11. Cloggedmowerdeckventholesfrombuildup 11. Clean around mandrels to open vent holes.  
of grass, leaves, trash around mandrels.  
1. Switch is “OFF”.  
1. Turn switch “ON”.  
Headlight(s) not  
working  
(if so equipped)  
2. Bulb(s) or lamp(s) burned out.  
3. Faulty light switch.  
4. Loose or damaged wiring.  
5. Blown fuse.  
2. Replace bulb(s) or lamp(s).  
3. Check/replace light switch.  
4. Check wiring and connections.  
5. Replace fuse.  
1. Bad battery cell(s).  
1. Replace battery.  
2. Check/clean all connections.  
3. Replace regulator.  
Battery will not  
charge  
2. Poor cable connections.  
3. Faulty regulator (if so equipped).  
4. Faulty alternator.  
4. Replace alternator.  
1. Freewheel control in “disengaged” position.  
2. Motion drive belt worn, damaged, or broken. 2. Replace motion drive belt.  
1. Place freewheel control in “engaged” position.  
Loss of drive  
3. Air trapped in transmission during  
shipment or servicing.  
3. Purge transmission.  
1. Engine throttle control not set between  
half and full speed (fast) position before  
stopping engine.  
1. Move throttle control between half and full speed  
(fast) position before stopping engine.  
Engine "back-  
fires” when turn-  
ing engine “OFF”  
1. Reverse operation system (ROS) is not  
"ON" while mower or other attachment is  
engaged.  
1. Turn ignition key to ROS "ON" position. See  
Operation section.  
Engine dies when  
tractor is shifted  
into reverse  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. LGT2554 (96045001500), PRODUCT NO. 960 45 00-15  
DECALS  
15  
16  
17  
16  
4
1
14  
14  
9
8
5
2
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
15  
16  
17  
- -  
- -  
- -  
532 18 09-41 Decal, Panel Side  
532 42 20-12 Decal, Hood Logo  
532 42 34-96 Decal, Replacement  
532 16 69-60 Decal, Bypass  
532 40 17-71 Pad, Footrest, LH  
532 40 17-70 Pad, Footrest, RH  
1
532 41 91-38 Decal, Warning  
2
532 42 38-30 Decal, Ethanol E85  
532 19 15-54 Decal, Hood Cust Resp  
532 17 84-55 Decal, Caution  
4
5
8
532 19 87-85 Decal, Mower Sch.  
532 14 50-05 Decal, Battery Dnge/Poi  
532 42 36-38 Decal, Panel Side  
9
14  
KEY  
NO.  
PART  
NO.  
WHEELS AND TIRES  
DESCRIPTION  
1
1
532 05 91-92 Cap, Valve, Tire  
2
532 06 51-39 Stem, Valve  
11  
2
3
3
532 14 45-09 Rim Assembly, Front  
532 00 81-34 Tube, Front (Service Item Only)  
532 10 62-30 Tire, Front  
532 12 49-57 Fitting, Grease (Front Wheel Only)  
532 12 49-59 Bearing,Flange(FrontWheelOnly)  
532 17 50-39 Cap, Axle (Front Wheel Only)  
532 18 47-08 Tire, Rear  
4
4
10  
5
7
6
5
7
9
8
6
8
9
10  
11  
- -  
532 00 71-54 Tube, Rear (Service Item Only)  
532 40 17-82 Rim Assembly, Rear  
532 14 43-34 Sealant, Tire (10 oz. Tube)  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
wheel_art_1-tex  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. LGT2554 (96045001500), PRODUCT NO. 960 45 00-15  
SCHEMATIC  
SCH12  
BATTERY  
SOLENOID  
STARTER  
RED  
A
M
RED  
FUSE  
AMMETER  
(OPTIONAL)  
BLACK  
ELECTRIC CLUTCH  
WHITE  
BLACK  
WHITE  
PTO SWITCH  
(DISENGAGED)  
S
H
WHITE  
BLACK  
RED  
M
B
G
C
A
B
A1  
GRAY  
A2  
L
RED  
CLUTCH/BRAKE  
(PEDAL UP)  
D
E
REVERSE SWITCH  
(NOT IN REVERSE)  
BLACK  
BLACK  
BLACK  
2
BLACK  
BLACK  
SEAT SWITCH  
(NOT OCCUPIED)  
BLACK  
BLACK  
3
1
GRAY  
6
JUNCTION  
CONNECTOR  
SHORTING  
CONNECTOR  
CHASSIS  
HARNESS  
H
G
C F  
SPARK  
IGNITION  
UNIT  
PLUGS GAP  
(2 PLUGS ON  
TWIN CYL. ENGINES)  
B
A
E
(OPTIONAL)  
BLUE  
BLACK  
HOUR  
METER  
D
BLACK  
BLUE  
FUEL  
LINE  
12V  
PTO SWITCH  
(MATING SIDE)  
POWER OUTLET  
(OPTIONAL)  
BLUE  
CHARGING SYSTEM OUTPUT  
9 - 1 6 AMP DC @ 3600 RPM  
FUEL SHUT-OFF  
SOLENOID  
(IF EQUIPPED)  
RED  
REGULATOR  
STATOR  
28 VOLTS AC @ 3600 RPM (REGULATOR DISCONNECTED)  
BLACK  
BROWN  
LIGHT  
SWITCH  
HEADLIGHTS  
WIRING INSULATED CLIPS  
NOTE: IF WIRING INSULATED  
CLIPS WERE REMOVED FOR  
SERVICING OF UNIT, THEY  
SHOULD BE RE-INSTALLED TO  
PROPERLY SECURE YOUR  
WIRING.  
3
6
6
5
3
2
IGNITION SWITCH  
NON-REMOVABLE  
CONNECTIONS  
2
1
5
4
POSITION CIRCUIT “MAKE”  
4
1
OFF  
M+G+A1  
B+A1  
RUN/OVERRIDE  
REMOVABLE  
CONNECTIONS  
CHASSIS HARNESS  
CONNECTOR  
DASH HARNESS  
CONNECTOR  
RUN  
B+A1  
L+A2  
START  
B + S + A1  
(MATING SIDE)  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. LGT2554 (96045001500), PRODUCT NO. 960 45 00-15  
ELECTRICAL  
T07S  
33  
22  
90  
30  
79  
21  
27  
2
1
24  
91  
99  
100  
34  
8
27  
43  
42  
41  
40  
26  
25  
55  
28  
16  
With 12V Outlet Option  
103  
71  
59  
94  
29  
With Service Minder Option  
92  
46  
93  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. LGT2554 (96045001500), PRODUCT NO. 960 45 00-15  
ELECTRICAL  
KEY PART  
NO. NO.  
DESCRIPTION  
1
532 16 34-65 Battery  
874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4  
532 18 64-91 Battery Box  
2
8
16  
21  
22  
24  
25  
26  
27  
28  
29  
30  
33  
34  
40  
41  
42  
43  
46  
50  
55  
59  
71  
79  
90  
91  
92  
93  
94  
99  
532 17 61-38 Switch Interlock  
532 18 37-59 Harness Socket Light  
532 00 41-52 Bulb, Light #1156  
532 40 02-53 Cable Battery  
532 41 28-95 Cable Starter  
532 17 51-58 Fuse  
873 51 04-00 Nut Keps Hex 1/4-20 unc  
532 14 54-91 Cable Ground 21" Blk 6 Ga.  
532 40 15-45 Switch Seat  
532 19 33-50 Switch Ign  
532 41 19-33 Key/Chain  
532 11 07-12 Switch Light/Reset  
532 40 11-04 Harness Ign. Dash  
817 72 04-08 Screw Thd Cut 1/4-20 x 1/2  
532 13 15-63 Cover Terminal Red  
532 19 25-07 Solenoid  
532 40 17-63 Gauge Hourmeter  
532 19 61-12 Switch PTO  
817 06 05-12 Screw Thdrol 5/16-18 x 3/4  
532 40 03-03 Outlet 12-Volt  
532 19 42-76 Harness Ign Chassis  
532 17 52-42 Socket Asm Bulb  
532 40 07-24 Cover Terminal Battery  
532 19 02-70 Strap Battery  
532 19 66-15 Harness Pigtail Reverse Switch  
532 19 25-40 Screw Plastite 10-14 X 2.00  
532 19 18-34 Module Reverse ROS  
817 67 04-12 Screw Hexwsh Thdrol 1/4-20 x 3/4  
100 819 09 14-16 Washer 9/32 x 7/8 x 16 Ga.  
103 532 40 79-62 Harness Pigtail 12 V Outlet  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. LGT2554 (96045001500), PRODUCT NO. 960 45 00-15  
CHASSIS  
15  
208  
299  
204  
18  
210  
298  
212  
296  
25  
214  
203  
130  
14  
234  
207  
206  
181  
211  
130  
209  
5
137  
176  
202  
234  
137  
205  
178  
176  
177  
175  
150  
289  
196  
176  
176  
182  
221  
36  
130  
236  
37  
235  
34  
68  
194  
36  
213  
162  
130  
180  
213  
218  
194  
199  
68  
165  
68  
183  
162  
189  
228  
68  
194  
217  
152  
233  
189  
228  
58  
52  
189  
189  
chassis-tex_TEX GT HUSQ_40_r1  
233  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. LGT2554 (96045001500), PRODUCT NO. 960 45 00-15  
CHASSIS  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
5
532 40 87-01 Dash  
203 532 40 30-76 Vent Side Hood LH  
204 532 41 66-13 Vent Asm Hood Top  
205 532 40 17-09 Skirt Hood Side RH  
206 532 40 17-11 Skirt Hood Side LH  
207 532 19 71-98 Bezel RH  
14  
15  
18  
25  
34  
36  
37  
52  
58  
68  
532 41 10-46 Hood Asm.  
532 19 89-07 Lens LH  
532 40 86-07 Grille Asm.  
532 19 89-06 Lens RH  
532 19 61-25 Plate Engine  
817 06 05-12 Screw 5/16-18 x 3/4  
532 40 18-25 Fender  
208 532 19 71-99 Bezel LH  
209 532 19 91-30 Insert Hex Top RH  
210 532 19 91-31 Insert Hex Top LH  
211 532 19 91-32 Insert Hex Bottom RH  
212 532 19 91-33 Insert Hex Bottom LH  
213 874 76 05-12 Bolt Hex Hd 5/16-18 unc x 3/4  
214 532 19 91-45 Clip Retainer  
217 532 40 91-67 Rod Pivot  
873 68 05-00 Nut Crown Lock 5/16-18  
532 19 43-14 Bracket Fender  
817 49 05-08 Screw 5/16-18 x 1/2  
130 532 41 63-58 Screw #10 x .750 BOS Thread  
137 532 40 75-90 Bumper Dash  
150 532 19 85-12 Duct Heat Hood  
218 532 19 63-95 Hood Stop  
152 532 19 95-35 Shield Browning/Debris  
162 532 14 24-32 Screw Hex Wsh Hi-Lo 1/4 x 1/2  
165 532 19 68-26 Bracket Support Tank  
175 532 19 63-04 Crossmember  
176 532 40 07-76 Screw 10-24 x 5/8  
177 532 19 52-27 Bushing Steering  
178 532 19 97-82 Cargo Asm. Net  
180 532 19 54-77 Chassis  
181 532 40 30-25 Bushing Mtg. Fender Crgo.  
182 532 40 68-59 Dash Lower  
221 532 19 89-09 Reflector LH  
228 532 19 51-61 Stud Fastener  
233 532 19 65-39 Bolt, Shoulder  
234 532 40 47-42 Bumper Hood  
235 532 40 61-29 Spacer Fender  
236 873 93 05-00 Nut Center Lock 5/16-18 unc  
289 532 40 35-71 Plug Cruise/Phone  
296 532 40 86-06 Trim  
298 532 11 04-52 Nut Push  
299 532 40 50-12 Logo  
183 874 78 05-20 Bolt Fin Hex 5/16-18 unc x 1-1/4  
189 817 00 05-12 Screw 5/16-18 x 3/4  
194 873 80 05-00 Nut Lock Hex Flange 5/16-18  
196 532 40 02-99 Console Asm. Deck Lift  
199 532 19 82-59 Plate Deck Lift  
NOTE: All component dimensions given in U.S. inches  
202 532 40 30-48 Vent Side Hood RH  
1 inch = 25.4 mm  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. LGT2554 (96045001500), PRODUCT NO. 960 45 00-15  
DRIVE  
74  
56  
220  
70  
185  
74  
216  
143  
221  
184  
197  
196  
35  
125  
42  
125  
80  
125  
64  
167  
159  
125  
170  
231  
160  
29  
51  
226  
188  
159  
185  
211  
17  
186  
187  
49  
189  
174  
233  
279  
15  
176  
166  
161  
23  
276  
50  
153  
190  
175  
178  
51  
125  
225  
33  
9
52  
51  
116  
7
22  
166  
162  
2
116  
205  
162  
230  
183  
9
183  
2
7
1
205  
33  
73  
99  
73  
230  
drive-tex_K46_fender_6  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. LGT2554 (96045001500), PRODUCT NO. 960 45 00-15  
DRIVE  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
532406206  
Transaxle, TUFFTORQ K46 AW  
(Internal parts not available)  
170 532 41 34-30 Keeper Belt Centerspan  
174 532 19 72-89 Nut Push  
2
532 18 62-11 Key  
175 532 40 62-08 Shaft Asm Shift  
176 532 19 62-14 Arm Clevis Rod Shift  
178 532 19 74-56 Spring Shift  
7
532 19 98-44 HubAsm.WheelRear22"TXGT.06  
532 14 00-80 Bolt Hub Wheel Rear  
819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.  
532 41 36-78 Spring Brake  
9
15  
17  
22  
23  
29  
33  
35  
42  
49  
50  
51  
52  
56  
64  
70  
73  
74  
80  
99  
183 532 40 04-24 Spacer Split  
184 532 40 31-18 Handle Parking Brake  
185 872 11 06-22 Bolt Rdhd Sqnk 3/8-16 x 2-3/4  
Gr. 5  
532 19 73-29 Rod Shift  
532 14 08-45 Knob  
532 40 38-06 Rod, Brake  
186 532 19 43-21 Spacer Retainer  
187 819 13 32-10 Washer  
812 00 00-01 Ring E  
532 19 95-91 Rod Brake Park  
532 12 48-72 Cover Foot Pedal  
872 11 06-14 Bolt  
188 532 19 43-23 Link Clutch Ground Drive  
189 532 19 43-17 Bellcrank Ground Drive  
190 532 19 43-18 Keeper Bellcrank Ground Drive  
196 817 00 06-16 Screw 3/8-16 x 1  
197 532 19 97-69 Link Clutch Anti-Rotation  
205 532 12 17-48 Washer  
532 19 43-27 Pulley Idler Flat  
873 90 06-00 Lock Nut 3/8-16  
532 19 43-26 Idler V-Groove 910" Offset  
532 13 09-69 V-Belt Drive  
211 532 19 62-12 Bushing Brake Shaft  
216 532 19 61-31 Bracket Pulley Idler  
220 532 19 89-08 Reflector RH  
532 19 62-00 Shaft Asm. Pedal Brake Control  
532 40 02-98 Console Asm.  
874 49 05-44 Bolt Hex Flghd 5/16-18 Gr. 5  
532 14 24-32 Screw 1/4 x 1/2  
532 41 00-24 Strap Torque  
221 532 40 31-87 Retainer Spring Clip Handle  
225 532 40 33-19 Keeper Belt Trans.  
226 532 40 08-31 Bracket Mount Torque  
230 532 18 89-67 Washer Hardened  
231 532 40 72-87 Idler V-Groove 1.688" Offset  
233 532 40 52-96 Washer Serrated  
276 874 78 07-16 Bolt 7/16-14 x 1 Gr. 5  
279 532 40 62-07 Link Shift  
532 41 57-43 Rod Bypass  
116 873 90 05-00 Nut Lock Hex Flange 5/16-18  
125 817 00 05-12 Screw 5/16-18 x 3/4  
143 817 49 05-08 Screw 5/16-18 x 1/2  
153 532 12 47-88 Retainer Spring  
159 876 02 04-12 Pin Cotter 1/8 x 3/4  
160 532 16 94-84 Retainer Clip  
282 532 40 04-24 Spacer Split .800 X .350 22" T  
161 532 10 57-09 Spring Return Clutch  
162 532 19 57-85 Spacer Transaxle 18 and 22  
166 532 19 72-90 Nut Push  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
167 532 40 52-57 Latch Brake Parking  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. LGT2554 (96045001500), PRODUCT NO. 960 45 00-15  
ENGINE  
21  
1
20  
22  
81  
87  
82  
18  
84  
45  
62  
15  
37  
69  
12  
28  
69  
37  
11  
71  
70  
91  
79  
41  
2
29  
42  
85  
9
90  
SPARK ARRESTER KIT  
Engine-tex_Kohl-2cyl_1_r2  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
Engine Kohl Model No. SV730  
DESCRIPTION  
62  
69  
70  
71  
79  
81  
82  
84  
85  
87  
90  
91  
532 14 66-29 Shield Heat Muffler  
1
- - - - - -  
532 14 97-23 Muffler  
- - - - - - - - -  
Gasket  
2
532 14 66-99 Tube Exhaust LH  
532 46 67-00 Tube Exhaust RH  
9
532 19 43-20 Keeper Belt Engine  
532 17 93-35 Clutch Electric  
11  
12  
15  
18  
20  
21  
22  
28  
29  
37  
41  
42  
45  
532 19 23-34 Screw Socket Head 5/16-18 x .75  
532 14 84-56 Tube Drain Oil Easy  
532 18 16-54 Plug Drain Oil  
532 19 43-43 Pulley Engine  
532 19 34-99 Tank Fuel 4.0  
532 19 42-67 Cap Asm  
817 12 06-16 Screw 3/8-16 x 1  
532 18 29-37 Control Throttle  
532 41 63-58 Screw #10 x .750 BOS Thread  
532 19 15-96 Control Choke  
532 17 99-53 Bolt Hex 7/16-20 x 3.75 Gr. 5  
532 19 82-39 Bolt 5/16-18 unc x 1 w/Sems  
817 00 06-16 Screw 3/8-16 x 1  
532 40 11-35 Fuel Line  
532 18 74-95 Bushing  
532 13 71-80 Spark Arrester Kit  
532 12 34-87 Clamp Hose  
532 12 61-97 Washer 1-1/2 OD x 15/32 ID x .250  
810 04 07-00 Washer Lock 7/16  
873 51 04-00 Nut Keps Hex 1/4-20 unc  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. LGT2554 (96045001500), PRODUCT NO. 960 45 00-15  
SEAT ASSEMBLY  
1
8
7
8
8
7
8
41  
40  
10  
21  
6
37  
37  
6
2
44  
43  
21  
3
seat-tex_6.5SL_3  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
37  
40  
41  
43  
44  
873 80 05-00 Nut, Lock 5/16-18 unc  
532 19 76-61 Handle Slide Seat  
532 19 82-00 Spring Latch Seat  
874 76 06-12 Bolt 3/8-16 x 3/4  
1
532 40 66-21 Seat  
2
532 18 01-66 Bracket Pivot Fender  
532 14 06-75 Strap, Asm Fender  
873 80 06-00 Nut, Lock w/Ins. 3/8-16 unc  
532 12 41-81 Spring, Seat Cprsn  
532 17 18-77 Bolt 5/16-18 unc x 3/4 w/Sems  
532 19 69-77 Pan, Seat  
3
6
819 13 38-12 Washer 13/32 x 2-3/8 x 12 Ga.  
7
8
10  
21  
NOTE: All component dimensions given in U.S. inches  
532 17 18-52 Bolt, Shoulder 5/16-18  
1 inch = 25.4 mm  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. LGT2554 (96045001500), PRODUCT NO. 960 45 00-15  
STEERING ASSEMBLY  
HUSQ SR  
PREM 2  
*
*
45  
51  
26  
26  
1
228  
1
*
21  
13  
16  
64  
28  
22  
60  
63  
28  
9
66  
8
63  
57  
7
67  
2
59  
19  
35  
9
8
7
6
58  
4
67  
6
5
15  
62  
13  
61  
14  
8
14  
15  
69  
70  
68  
13  
53  
steering-tex_special_13_r1  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. LGT2554 (96045001500), PRODUCT NO. 960 45 00-15  
STEERING ASSEMBLY  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
51  
53  
57  
58  
59  
60  
61  
62  
63  
64  
66  
67  
68  
69  
70  
873 94 08-00 Nut Hex Jam Toplock 1/2-20 unf  
532 18 89-67 WasherHardened.793x1.637x.060  
532 19 72-46 Bracket Upstop  
532 19 47-47 Bolt Shoulder Sector Pivot CFM  
532 19 47-48 Washer Thrust Sector Steering  
873 97 10-00 Nut Flange Lock 5/8-11  
532 19 47-40 Draglink, LH  
532 19 47-41 Draglink, RH  
817 00 05-12 Screw 5/16-18 x 3/4  
532 19 98-49 Retainer Clip Spring Steering  
871 02 07-48 Bolt Hex Fghd 7/16-14 x 3 Serr  
532 19 47-37 Bushing PM Front Axle  
873 90 07-00 Nut Lock Flange 7/16-14 Gr. 5  
532 19 91-62 Washer 1.5 x .505 x .118  
532 19 61-97 Bracket Deck Susp. Front  
1
532 42 34-69 Wheel, Steering  
2
532 19 59-68 Axle Asm., Front  
4
532 40 30-89 Spindle Asm., LH  
532 40 30-90 Spindle Asm., RH  
532 12 49-31 Bearing, Race Thrust Harden  
532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.  
812 00 00-29 Ring, Clip #T5304-75  
532 12 12-32 Cap, Spindle  
532 12 17-49 Washer 25/32 x 1-1/4 x 16 Ga.  
810 04 06-00 Washer, Lock Hvy Hlcl Spr 3/8  
873 54 06-00 Nut, Crown Lock 3/8-24 unf  
532 40 82-19 Shaft Steering  
532 19 47-29 Plate Steering  
532 18 67-37 Adapter, Wheel Steering  
532 19 48-45 Bushing, Strg. Blk  
5
6
7
8
9
13  
14  
15  
16  
19  
21  
22  
26  
28  
35  
45  
532 41 59-87 Insert, Wheel Steering  
817 00 06-12 Screw 3/8-16 x 3/4  
532 19 47-32 Gear, Sector Plate  
819 18 38-12 Washer 9/16 x 2-3/8 x 12 Ga.  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. LGT2554 (96045001500), PRODUCT NO. 960 45 00-15  
MOWER DECK  
46  
46  
47  
185  
39  
6
34  
192  
49  
46  
21  
122  
52  
7
114  
43  
196  
49  
97  
33  
31  
33  
98  
32  
52  
32  
241  
33  
31  
1
242  
30  
116  
117  
120  
49  
29  
50  
25  
113  
21  
26  
24  
194  
12  
59  
16  
19  
27  
21  
60  
18  
15  
18  
58  
190  
14  
189  
21  
18  
190  
13  
11  
187  
188  
8
187  
mower_deck 54-tex_16  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. LGT2554 (96045001500), PRODUCT NO. 960 45 00-15  
MOWER DECK  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
532 40 31-25 Deck Weldment Mower  
532 19 60-66 Cover Mandrel LH  
532 19 71-81 Cover Mandrel RH  
532 19 30-03 Bolt 7/16 Asm. Blade  
532 18 72-56 Blade Bagging  
58  
59  
60  
97  
98  
532 18 73-42 Baffle Right  
532 18 73-44 Baffle Left  
532 18 76-07 Baffle Center  
532 17 85-15 Washer Hardened  
532 19 61-05 Spring Drive  
6
7
8
11  
- -  
12  
13  
14  
16  
15  
18  
19  
21  
24  
25  
26  
27  
29  
30  
31  
32  
33  
34  
39  
43  
46  
47  
49  
50  
52  
532 18 72-55 Blade Mulching  
113 872 11 05-08 Bolt Rdhd Sqnk 5/16-18 x 3/4  
114 532 18 75-56 Rod Tension Relief  
116 532 19 34-06 Bolt, Shoulder  
532 40 48-51 Rod Anti Sway  
532 18 72-91 Shaft Asm. w/Lower Bearing  
532 18 72-81 Housing, Mandrel  
819 13 13-12 Washer 3/8  
117 532 17 48-73 Gauge Wheel  
120 819 13 20-12 Washer 13/32 x 1-1/4 x 12 Ga.  
122 532 18 75-57 Bushing Tension Relief  
185 873 90 07-00 Nut Lock Flange 7/16-14 Gr. 5  
187 532 19 51-61 Stud Fastener w/"D" Anti-Rotation  
188 873 90 05-00 Nut Lock Hex Flange  
189 532 19 51-85 Arm Susp. Mower Rear  
190 532 19 65-39 Bolt Shoulder  
532 11 04-85 Bearing, Ball, Mandrel  
872 14 05-05 Bolt Carriage 5/16-18 x 5/8  
532 19 42-08 Pin Cotter 5/16 Bowtie  
873 68 05-00 Nut, Crownlock 5/16-18 unc  
532 10 53-04 Cap Sleeve  
532 17 81-02 Spring, Torsion  
532 11 04-52 Nut, Push  
192 532 19 84-68 Keeper Belt Idler  
532 18 89-38 Deflector Shield  
194 872 14 07-16 Bolt Carr Sqnk 7/16-24 x 2  
196 872 14 06-20 Bolt Rdhd 3/8-16 x 2-1/2 Gr. 5  
241 532 15 29-27 Screw  
532 13 14-91 Rod, Hinge  
532 17 39-84 Screw, Thdroll Washer Head  
532 18 76-90 Washer, Spacer Mower Vented  
532 15 35-35 Pulley, Mandrel  
242 532 41 55-98 Washout Port  
- -  
- -  
532 41 64-05 Coupling, Quick Connect  
532 18 72-92 Mandrel Assembly (Includes  
housing, shaft assembly, and  
532 40 02-34 Nut, Flg. Top Lock  
873 68 06-00 Nut Crownlock 3/8-16 unc  
532 19 73-80 Pulley, Idler, Stationary LH  
532 19 60-65 Arm, Idler  
532 13 77-29 Screw, Thdroll. 1/4-20 x 5/8  
532 19 61-03 Belt Deck Drive  
873 90 06-00 Nut, Lock Flg. 3/8-16 unc  
872 11 06-16 Bolt Rdhd Sqnk 3/8-16 unc x 2  
532 19 73-79 Pulley Idler  
bearing only - pulley/nut/washer  
and blade bolt/washers not in-  
cluded)  
- -  
532 19 93-00 Replacement Mower, Complete  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - MODEL NO. LGT2554 (96045001500), PRODUCT NO. 960 45 00-15  
MOWER LIFT  
7
87  
87  
90  
98  
89  
3
10  
88  
97  
2
97  
91  
87  
89  
lift-tex_3  
89  
87  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
2
532 19 52-23 Shaft Asm., Lift  
532 19 52-30 Lever Asm., Lift RH  
532 41 15-55 Grip, Lever  
90  
91  
97  
98  
532 19 42-08 Pin Cotter 5/16 Bow Tie Lock  
532 40 34-07 Link Lift Susp Mower Rear  
817 00 06-12 Screw 3/8-16 x 3/4  
3
7
10  
87  
88  
89  
532 19 63-14 Spring Torsion  
532 19 52-64 Link Lift Susp. Front Mower  
532 19 42-09 Pin Cotter 7/16 Bow Tie Lock  
532 19 53-04 Spring Lift Assist  
819 17 19-12 Washer Clear Zinc  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HUSQVARNA PRODUCT REGISTRATION INFORMATION & WARRANTY STATEMENT  
All Husqvarna products can be registered online at www.usa.husqvarna.com quickly and easily regardless of their model year. Click the Support tab,  
then click on the Online Product Registration link, and fill out the electronic form and submit. Ask about Husqvarna s extended service plan!  
SECTION 1: LIMITED WARRANTY  
Husqvarna Professional Products, Inc (“Husqvarna”) warrants the original purchaser the Husqvarna branded product to which this warranty apply (the “Product”) that the Product shall be free from defects in material and workmanship  
from the date of purchase for the period of the applicable “Warranty Schedule” of the Product as set forth below. Additional limitations are described in Section 2 through 6, inclusive.  
COMMERCIAL /  
PROFESIONAL  
WARRANTY SCHEDULE  
RENTAL  
WARRANTY  
SCHEDULE  
CONSUMER  
WARRANTY SCHEDULE*  
PRODUCT CATEGORY  
Reconditioned Products: Reconditioned chainsaws, trimmers, brushcutters, clearing saws, handheld blowers,  
backpack blowers, hedge trimmers, and electrical products.  
90 Days  
2 Years  
2 Years  
2 Years  
N/A  
N/A  
Chain Saws Lifetime Ignition Warranty (Parts Only). One Year Conditional Crankshaft Warranty for Commercial/Professional use when operated with  
90 Days  
1 Year  
1 Year  
90 Days  
Husqvarna XP 2 cycle oil (Parts & Labor).  
100 Series Trimmers, Stick Edgers, Hedge Trimmers  
Lifetime Ignition Warranty (Parts Only). Lifetime Shaft Warranty.  
90 Days  
90 Days  
200 & 300 Series Trimmers, Brushcutters, Clearing Saws, Stick Edgers, Hovering Trimmers & Hedge Trimmers  
Lifetime Ignition Warranty (Parts Only) and Lifetime Shaft Warranty apply to these products (excludes Hovering Trimmers).  
2 Years  
1 Year  
2 Years  
1 Year  
N/A  
90 Days  
90 Days  
N/A  
Blowers (Lifetime Ignition Warranty - Parts Only)  
Pole Pruners, Pole Saws, Pole Hedge Trimmers (Lifetime Ignition Warranty - Parts Only)  
Residential Walk-Behind Mowers, Tillers, LE389 Edger †  
LE475 Edger †  
2 Years  
2 Years  
90 Days  
90 Days  
LT, LTH, LS, XLS, GLS, YT, YTH, GT, GTH, 16H, Pro15, 155 ProFlex Series Lawn & Garden Riders and  
Residential Zero Turn Mowers †  
2 Years  
N/A  
N/A  
2 Years ¥  
2 Years ¥  
1 Year  
90 Days  
90 Days  
90 Days  
1 Year  
MZ and EZ Series Zero Turn Riders †  
iZ, LZ, BZ Series Zero Turn Riders † (Applies to units factory-equipped with Roll Over Protection System.)  
Commercial Walk Mowers † (includes 21” & wide area)  
Commercial Turf Specialty Equipment †  
Zero Turn & Commercial Turf Specialty Attachments  
Power Cutters (Lifetime Ignition Warranty - Parts Only)  
Automatic Mower (1 Year Battery Warranty)  
2 Years ¥  
2 Years ¥  
1 Years  
2 Years ¥  
1 Years  
2 Years  
1 Year  
1 Year  
90 Days  
90 Days  
N/A  
90 Days  
1 Year (K750 only)  
2 Years  
2 Years  
N/A  
90 Days  
90 Days  
Snow Throwers †  
2 Years  
2 Years  
N/A  
N/A  
Pressure Washers †  
(Excludes 5525PW)  
2 Years  
2 Years – 1365GN only  
(2nd Year Parts only)  
(2nd Year Parts Only)  
Generators (Husqvarna s warranty does not cover Engine & Generator Parts, which are warrantied by responsible manufacturer.) †  
Grass Catchers & Bumpers Purchased with New Units  
Spreaders  
Same Warranty As Unit When Purchased with Unit  
1 Year  
30 days  
Parts & Accessories Purchased Separately  
2 Year or 2,000 Hour Powertrain & 1 Year or 1,000 Hour Body Warranty  
Husqvarna Utility Vehicles**(Engines/transmissions shall be warrantied through Husqvarna.)  
HUV Batteries: 4210E Versions  
4 Year Pro-rated  
90-day  
Husqvarna Safety Apparel***  
1 year  
N/A  
Batteries**** (Consumer Products where applicable)  
Replacement Parts, Accessories including Bars and Chains, Tools and Display Items. Emission Control System Components necessary to  
comply with CARB-TIER II and EPA Regulations (Excludes components which are part of engine systems manufactured by third part engine manufacturers for  
which the purchaser has received a separate warranty with product at time of purchase.)  
30 Day Warranty  
Download from Www.Somanuals.com. All Manuals Search And Download.  
† Refer to Section 3 for items not covered by this warranty  
*All consumer product use must have been limited to the owner s residence. Warranted for noncommercial, nonprofessional, noninstitutional and nonincome producing use.  
**HUV 2 Year or 2,000 Hour Powertrain (The engine assembly, unitized transaxle assembly (gasoline vehicle), motor, and main frame assembly are warranted with respect to parts and labor against defects in material and  
workmanship or a period of two years or 2000 hours of operation, whichever first occurs, from the date of purchase.) & 1 Year or 1,000 Hour Body Warranty (All remaining components of the vehicle not specified otherwise and all  
other original equipment options and accessories supplied by Husqvarna are warranted with respect to parts and labor against defects in material and workmanship for a period of one year or 1000 hours of operation, whichever first  
occurs, from the date of purchase.)  
HUV s Gas & Diesel Powered Battery: 0 – 6 months free replacement and 7 – 12 months prorated  
HUV s Electric Powered – 4 year or 16,000 Energy Unit Limited Warranty Period  
***Husqvarna safety apparel warranty is from the date of the customer s original purchase for defects in material and workmanship. Normal wear, tear or abuse is not covered under warranty. All care and maintenance instructions  
must be followed as stated by the manufacturer on the care label. The fit of the protective apparel/boot is not covered under warranty.  
****Battery 1 Year prorated limited warranty with 100% replacement during the first 6 months.  
¥ Effective manufacturing date 2/1/09. Units with serial number started 0905XXXXX or greater are affected.  
Lifetime Warranty (Parts and Labor): All tiller tines and trimmer shafts against breakage. Proof of purchase required.  
Lifetime Warranty (“PARTS ONLY” after initial warranty expiration): Ignition coils and modules on handheld product. Proof of purchase required.  
SECTION 2: HUSQVARNA S OBLIGATIONS UNDER THE WARRANTY  
Husqvarna will repair or replace defective components without charge for parts or labor if a component fails because of a defect in material or workmanship during the warranty period.  
SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY  
The following items are not covered by this warranty:  
(1) Normal customer maintenance items which become worn through normal regular use, including, but not limited to, belts, blades, blade adapters, bulbs, clutches, clutch drums, filters (fuel line, fuel filters, air filters, oil filters),  
sprockets, guide bars, lubricants, rewind springs, saw chain, spark plugs, starter ropes and tiller tines;  
(2) Natural discoloration of material due to ultraviolet light;  
(3) Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective manufacturer s warranty as provided in writing with the product information supplied at the time of purchase; all claims must be  
sent to the appropriate manufacturer.  
(4) Lawn and garden attachments that are covered by a third party which gives a warranty, all claims for warranty should be sent to the manufacturer.  
(5) Commercial or consumer mowing decks with sand abrasion damage.  
(6) Emission Control System components necessary to comply with CARB-TIER II and EPA regulations which are manufactured by third party engine manufacturer.  
SECTION 4: EXCEPTIONS AND LIMITATIONS  
This warranty shall be inapplicable to defects resulting from the following:  
(1) Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any adverse reaction due to incorrect storage or use habits;  
(2) Failure to operate or maintain the unit in accordance with the Owner s/Operator s manual or instruction sheet furnished by Husqvarna;  
(3) Alterations or modifications that change the intended use of the product or affects the product s performance, operation, safety, or durability, or causes the product to fail to comply with any applicable laws; or:  
(4) Additional damage to parts or components due to continued use occurring after any of the above.  
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES  
FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A  
PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO THE WARRANTY PERIOD AS DEFINED IN THE LIMITED WARRANTY STATEMENT. HUSQVARNA RESERVES THE RIGHT TO CHANGE OR  
IMPROVE THE DESIGN OF THE PRODUCT WITHOUT NOTICE, AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY MANUFACTURED PRODUCTS.  
Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal  
rights, and you may also have other rights which vary by state.  
SECTION 5: CUSTOMER RESPONSIBILITIES  
The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written in the maintenance section of the Owner s/Operator s manual. Should an operational problem or failure occur, the product  
should not be used. Failure caused by continued use is not covered by warranty. Product should be delivered, at owners expense, as is, to an authorized Husqvarna Servicing Retailer for evaluation. Proof of purchase, as explained  
in section 6, rests solely with the customer.  
SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION  
It is the Owner s and Retailer s responsibility to make certain that the Warranty Registration Card is properly filled out and mailed to Husqvarna. This card should be mailed within ten (10) days from the date of purchase in order to  
confirm the warranty and to facilitate post-sale service. Proof of purchase must be presented to the authorized Husqvarna retailer in order to obtain warranty service. This proof must include date purchased, model number, serial  
number, and complete name and address of the selling retailer. To obtain the benefit of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna retailer in a timely manner, no later than thirty  
(30) days from date of the operational problem or failure. The product must be delivered at the owner s expense. Downtime, pick-up and delivery charges are not covered by this warranty. An authorized Husqvarna retailer can be  
located by calling 1-800-HUSKY-62 or visiting www.husqvarna.com  
Subject to change without notice.  
HUSQVARNA 7349 Statesville Road, Charlotte, NC 28269  
Part # 531 30 96-85  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Bolens Lawn Mower 117 530A User Manual
Craftsman Lawn Mower Accessory 61024600 User Manual
Dixon Lawn Mower ZTR 2301 User Manual
Hayter Mowers Lawn Mower 410D User Manual
Hayter Mowers Lawn Mower E131B User Manual
Hubbell Lawn Mower UH18 User Manual
Husqvarna Lawn Mower 532 42 62 26 User Manual
Poulan Lawn Mower 177937 User Manual
Scag Power Equipment Lawn Mower SW32 15KAI User Manual
Snapper Lawn Mower N281016BE User Manual