Dixon Lawn Mower ZTR 428 User Manual

TECHNICAL DATA BROCHURE - ZTR 428 & 429  
DATE 8/89 (Rev.)  
PAGE  
1
of 11  
MPORTANT -- READ OPERATOR’S MANUAL BEFORE OPERATING OR MAKING ADJUSTMENTS.  
Deluxe Seat Adjustment  
Easy hand lever action allows forward and backward movement, of seat.  
No bolts to loosen or tighten.  
Mower Blade Operation  
1.  
To start mower blades, pull up slightly on blade drive switch handle  
and move it forward to the "ON" position.  
To stop mower blades, move switch handle to the "OFF" position.  
2.  
Body Removal  
1.  
Disconnect throttle cable from engine.  
2.  
Disconnect rear wiring loon from the body-by turning the threaded collar  
on connector in a counterclockwise direction. This plug is located at  
the right rear of body.  
3.  
4.  
5.  
6.  
Remove the four control lever bolts and remove upper control levers  
(P/N 9079 A 9080).  
Remove the two acorn nuts on floor of body and release latches on  
the rear of body near each side.  
Place height adjustment lever in the vertical position, engage the  
parking brake and carefully lift body off the chassis.  
Reverse above procedures to install body.  
Safety Checks -- "Important"  
1.  
After reassembly of body onto chassis and while seated on the mower,  
attempt to start the engine with mower deck engaged. The engine should  
not start. If engine does start, return mower to an Authorized Dixon Dealer  
for adjustment or repair.  
2.  
Disengage mower deck and start engine with the operator in a normal seated  
position on the mower. Engage mower deck and remove weight from the  
seat. The engine should stop. If engine does not stop when operator rises  
from seat, return mower to an Authorized Dixon Dealer for adjustment or  
repair.  
Parking Brake Adjustment  
1.  
2 .  
Remove body as described above.  
Adjustment points are located at rear of transaxle on each side.  
Remove roll pins from swivel fitting (P/N 2172). Turn swivel fitting on  
brake rod (P/N 6100) in, to tighten. Just enough to prevent brake from  
slipping when engaged. 3.  
Reinstall roll pin.  
CAUTION: Over tightening may cause premature wear, on brake band  
(P/N 6085).  
Dixon Industries, INC  
.
Box 1569  
Coffeyville, Kansas 67337-0945 (316)251-2000  
Airport Industrial Park  
TELEX: 417109  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHASSIS ASSEMBLY (MODEL 429 & 428)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BODY ASSEMBLY (MODEL 429 & 428)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ENGINE ASSEMBLIES (MODEL 429 & 428)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIRING (MODEL 429 & 428)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

American Lawn Mower Co Lawn Mower UT13120 User Manual
Cisco Systems Lawn Mower MM275 User Manual
Cub Cadet Lawn Mower 190 190 100 User Manual
Hustler Turf Lawn Mower 114675_0311 C 1 User Manual
Snapper Lawn Mower 19E07B User Manual
Snapper Lawn Mower 06125 User Manual
Snapper Lawn Mower Conquest 2700 User Manual
Snapper Lawn Mower FM7300 User Manual
Snapper Lawn Mower MR216017B User Manual
Snapper Lawn Mower ZF5200M User Manual