BILLY GOAT ® MV650H PUSH Vacuum
Owner’s Manual
Accessories
Caster Kit
Use on hard surface
for maneuverability.
Hose Kit
For vacuuming hard
to reach areas.
Bag Liner Kit
To collect leaves,
thatch, and grass.
Felt Bag Kit
Use on all dusty
conditions.
P/N 840129
P/N 840116
P/N 840134
P/N 840194
Part No 840186
1
Form No F030106A
MV650H PUSH Vacuum Owner’s Manual
SERIAL PLATE DATA
Record the model number, serial number, date of
purchase, and where purchased.
Purchase Date:
Purchased From:
MV 650 SERIES SPECIFICATIONS
MV650
Honda GSV190AA1A
Engine Type
Horsepower
6.5 (4.85 kW)
Fuel Capacity
1.6 qt (1.5 L)
Oil Capacity
0.69 qt (0.65L)
28 lbs (12.7 kg)
157 lbs (71.2 kg)
180 lbs (81.7 kg)
28” Wide x 62.5” Long x 45.5” High
20°
Engine Weight
Unit Weight
Shipping Weight
Overall Dimensions
Maximum Operating Slope
COMMON REPLACEMENT PARTS
• Bag. P/N 840189. Original equipment replacement bag.
• Skid. P/N 840041. Nozzle wear guard skid.
Form No F030106A
3
Part No 840186
MV650H PUSH Vacuum Owner’s Manual
GENERAL SAFETY INSTRUCTIONS and SYMBOLS
The safety symbols shown below are used throughout this manual. You should become familiar with them
before assembling, operating or servicing this equipment.
This symbol indicates important information that will prevent injury to yourself or others.
This symbol indicates ear protection is recommended when operating this equipment.
This symbol indicates eye protection is recommended when operating this equipment.
This symbol indicates gloves should be worn when servicing this equipment.
This symbol indicates that this manual and the engine manufacturer’s manual should be read
carefully before assembling, operation, or servicing this equipment.
This symbol indicates important information that will prevent damage to your BILLY GOAT ®
MV Vacuum.
This symbol indicates the engine oil level should be checked before operating this
equipment.
Read and make sure you thoroughly understand the following safety precautions before assembling, operating
or servicing this equipment:
READ this manual and the engine manufacturer’s manual carefully before assembling,
operating, or servicing this equipment.
EAR PROTECTION is recommended when operating this equipment.
EYE PROTECTION is recommended when operating this equipment.
EXHAUST from this product contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
DO NOT operate this equipment on any unimproved forested, brushy, or grass covered land
unless a spark arrester is installed on the muffler as required by Section 4442 of the
California Public Resources Code. The arrester must be maintained in good working order.
Other states may have similar laws. Federal laws apply on federal lands.
DO NOT run engine in an enclosed area. Exhaust gases contain carbon monoxide, an
odorless and possibly fatal poison.
Part No 840186
4
Form No F030106A
MV650H PUSH Vacuum Owner’s Manual
DO NOT run this equipment indoors or in any poorly ventilated area. Refueling outdoors
is recommended.
DO NOT refuel this equipment while the engine is running. Allow engine to cool for at
least two minutes before refueling.
DO NOT store gasoline near an open flame.
DO NOT remove gas cap while engine is running.
DO NOT start or operate engine if strong odor of gasoline is present.
DO NOT start or operate engine if gasoline is spilled. Move equipment away from spill
until gasoline has completely evaporated.
DO NOT smoke while filling the fuel tank.
DO NOT check for spark with spark plug or spark plug wire removed. Use an approved
spark tester.
DO NOT operate engine without a muffler. Inspect muffler periodically and replace if
necessary. If equipped with muffler deflector, inspect deflector periodically and replace if
necessary.
DO NOT operate engine with grass, leaves or other combustible material near the
muffler.
DO NOT touch muffler, cylinder, or cooling fins when hot. Contact with hot surfaces may
cause severe burns.
DO NOT leave equipment unattended while in operation.
DO NOT park equipment on a steep grade or slope.
DO NOT operate equipment with bystanders in or near the work area.
DO NOT allow children to operate this equipment.
DO NOT operate equipment with guards removed.
DO NOT operate equipment near hot or burning debris or any toxic or explosive
materials.
DO NOT operate equipment on slopes greater than specified in Specifications section of
this manual.
ALWAYS remove spark plug wire when servicing equipment to prevent accidental
starting.
ALWAYS check fuel lines and fittings frequently for cracks or leaks. Replace if
necessary.
ALWAYS keep hands and feet away from moving or rotating parts.
ALWAYS store fuel in approved safety containers.
Form No F030106A
5
Part No 840186
MV650H PUSH Vacuum Owner’s Manual
SOUND DATA
SOUND LEVEL 105 Dba at Operator Position
Sound tests were conducted in accordance with 2000/14/EEC and were performed on 12-12-2005 under the
conditions listed below.
Sound power level listed is the highest value for any model covered in this manual. Please refer to
serial plate on the unit for the sound power level for your model.
General Conditions:
Temperature:
Sunny
41oF (5oC)
Wind Speed:
Wind Direction:
Humidity:
9.2 mph (14.8kph)
Northwest
59%
Barometric Pressure:
30.13” Hg (765mm Hg)
VIBRATION DATA
VIBRATION LEVEL 2.3g
Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using
calibrated vibration test equipment. Tests were performed on 12-12-2005 under the conditions listed below.
General Conditions:
Temperature:
Sunny
41oF (5oC)
Wind Speed:
Wind Direction:
Humidity:
9.2 mph (14.8kph)
Northwest
59%
Barometric Pressure:
30.13” Hg (765mm Hg)
INTENDED USE
Your BILLY GOAT ® MV Vacuum is designed for vacuuming leaves, grass clippings, and other types of organic
litter, as well as, debris mixed with cans, bottles and small amounts of sand; however, vacuuming cans, bottles
and sand will affect the longevity of your machine.
Like all mechanical tools, reasonable care must be used when operating the machine.
Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and
check for damaged or worn impeller, loose impeller bolt, loose impeller key, loose engine or lodged foreign
objects. Note: See parts list for proper impeller bolt torque specifications. (See trouble shooting section on page
25).
Part No 840186
6
Form No F030106A
MV650H PUSH Vacuum Owner’s Manual
INSTRUCTION LABELS
®
The labels shown below were installed on your BILLY GOAT MV Vacuum. If any labels are damaged or
missing, replace them before operating this equipment. Item numbers from the Illustrated Parts List and part
numbers are provided for convenience in ordering replacement labels. The correct position for each label may
be determined by referring to the Figure and Item numbers shown.
PN 400268
PN 890254
PN 840054
(See Figure 3 Item 55)
(See Figure 4 Item 162)
(See Figure 1 Item 34)
PN 400424
PN 810736
PN 890301
(See Figure 1 Item 11)
(See Figure 4 Item 174)
(See Figure 4 Item 163)
PN 840080
(See Figure 4 Item 175)
ENGINE LABELS
CONTROLS
PN 840045
(See Figure 3 Item 57)
Form No F030106A
7
Part No 840186
MV650H PUSH Vacuum Owner’s Manual
MV Vacuum Assembly Drawing
Part No 840186
8
Form No F030106A
MV650H PUSH Vacuum Owner’s Manual
PARTS LIST
Form No F030106A
9
Part No 840186
MV650H PUSH Vacuum Owner’s Manual
ASSEMBLY INSTRUCTIONS
Your BILLY GOAT ® MV Vacuum was shipped in one carton, completely assembled except for the Hood/Upper
Handle Assembly. Mounting hardware for the Hood/Upper Handle Assembly is temporarily installed on the lower
handle and the Housing assembly.
READ all safety instructions before assembling unit.
TAKE CAUTION when removing the unit from the box the Hood/Upper Handle Assembly is
attached to the unit by cables.
Remove unit from carton. Make sure the following items that have been packed with unit:
Parts bag P/N 840190
†
†
†
†
†
Owner’s Manual, P/N 840186
Honda Engine Manual
Warranty Card, P/N 400972
Ty-Wraps (2 ea)
Hardware Bag P/N 840190
DISCONNECT spark plug wire before assembling unit.
1. Attach hood assembly to the housing then hold in
place during the step 2.
2. Install item #170 center bolt first when aligned with a nut
on the housing.
3. Attach rest of hood assembly to the housing using
corresponding hardware.
NOTE: BE SURE ALL CABLES ARE ROUTED ON
THE UNDERSIDE OF THE HOOD AND HOUSING.
NOTE: You will have to insert the bolt/washer from the
inside by reaching through the hood.
- Two 7/16” wrenches.
Part No 840186
10
Form No F030106A
MV650H PUSH Vacuum Owner’s Manual
4. Attach upper handle brace to lower handle using
corresponding hardware. Then repeat this step on the
other side.
5. Attach rod end (164) to the nozzle door rod then
secure in place by tightening jam nut.
6. Attach nozzle door rod to the nozzle door using
corresponding hardware.
NOTE: It is easier to do this with nozzle door closed.
- Two 1/2” wrenches.
- Two 9/16” wrenches.
7. Attach rod end to rod (as in step 5).
9. Install cable ty wraps.
10. Reconnect spark plug wire.
11. Attach the bag.
8. Attach nozzle door rod to the lever with
nozzle door closed and lever in hose kit
position.
NOTE: Check to see nozzle door open and
close all the way (see page 15). Tighten or
loosen the rod end (164) for any
adjustments.
Two 9/16”
wrenches.
Form No F030106A
11
Part No 840186
MV650H PUSH Vacuum Owner’s Manual
OPERATION
DO NOT run engine in an enclosed area. Exhaust gases contain carbon monoxide, an
odorless and possibly fatal poison.
DO NOT start or operate engine if strong odor of gasoline is present.
DO NOT start or operate engine if gasoline is spilled. Move equipment away from spill
until gasoline has completely evaporated.
DO NOT operate engine without a muffler. Inspect muffler periodically and replace if
necessary. If equipped with muffler deflector, inspect deflector periodically and replace
if necessary.
DO NOT operate engine with grass, leaves, or other combustible material near the
muffler.
DO NOT touch muffler, cylinder or cooling fins while engine is running. Contact with hot
surfaces may cause severe burns.
DO NOT operate equipment with bystanders in or near the work area.
DO NOT operate equipment with guards removed.
DO NOT operate equipment in areas containing rock, glass, string-like material, wire,
rags, cans, metal, or other non-organic material.
DO NOT operate equipment on slopes greater than specified in Specifications section
of this manual.
DO NOT operate equipment near hot or burning debris or any toxic or explosive
materials.
DO NOT allow children to operate this equipment.
ALWAYS keep hands and feet away from moving or rotating parts.
EAR PROTECTION is recommended when operating this equipment.
EYE PROTECTION is recommended when operating this equipment.
Part No 840186
12
Form No F030106A
MV650H PUSH Vacuum Owner’s Manual
OPERATOR CONTROLS
The operator’s position is at the rear of the machine between the handlebars. The operator should STAND in a
position to allow both handlebars to be grasped firmly, which allows sufficient leverage to steer the machine.
Operator’s controls are shown below.
3
4
1
2
Operator Control Locations
1
2
3
Nozzle Door Adjuster
Bag Latch
Pull Starter
4
Throttle Control
STARTING
CHECK engine oil level before operating machine.
1. Place equipment on a level, firm surface that is free of rocks or other debris.
2. Place throttle in CHOKE position.
Throttle
DO NOT START equipment without the debris bag in place.
Form No F030106A
13
Part No 840186
MV650H PUSH Vacuum Owner’s Manual
3. Pull starter rope to start engine.
PULL STARTER CORD slowly until resistance is felt. Then pull cord rapidly to avoid
kickback.
4. Move throttle control back to RUN position and allow engine to reach correct operating speed.
VACUUM NOZZLE HEIGHT ADJUSTMENT
FOR MAXIMUM PICKUP: Adjust nozzle height as close to debris as possible, but without blocking airflow into
the nozzle. NOTE: Never bury nozzle into debris. The vacuum nozzle is raised and lowered by turning the crank
handle clockwise and counter-clockwise.
Part No 840186
14
Form No F030106A
MV650H PUSH Vacuum Owner’s Manual
VACUUM NOZZLE DOOR ADJUSTMENT
The vacuum nozzle door adjusts for the maximum performance under various applications.
Nozzle fully opened. This is ideal for turf application
Nozzle half way opened. This is ideal for hard surface application
Nozzle closed for OPTIONAL hose kit. This is ideal TO USE WITH THE HOSE KIT.
Form No F030106A
15
Part No 840186
MV650H PUSH Vacuum Owner’s Manual
VACUUMING OPERATION
This machine is designed for vacuuming leaves, grass clippings, and other types of organic litter.
Debris mixed with cans, bottles, and small amounts of sand can be vacuumed; however, it is not this
machine's primary purpose. Vacuuming cans, bottles, and sand will affect the longevity of your machine. In
dusty conditions it maybe necessary to purchase Felt Bag Kit (P/N 840022).
Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and
check for damaged or worn impeller, loose impeller bolt, loose impeller key, loose engine or lodged foreign
objects. Note: See parts list for proper impeller bolt torque specifications. (See trouble shooting section on
page 22).
SHUT DOWN
1. Pull Throttle Control all the way back to the STOP position.
CLEARING A CLOGGED NOZZLE
DISCONNECT spark plug wire before servicing unit.
1. Shut engine off and wait for impeller to stop completely.
2. Disconnect spark plug wire.
3. Wearing durable gloves, remove clog.
WEAR durable gloves. Clog may contain sharp materials.
4. Reconnect spark plug wire.
DEBRIS BAG
Debris bags are normal replaceable wear items.
Frequently empty debris to prevent bag overloading with more weight than you
can lift.
Bag liners are available for use in various conditions where debris will be vacuumed. (see Bag Liner Options
shown on page 1).
DO NOT place bag on or near hot surface, such as engine.
Be sure engine has come to a complete stop before removing or emptying bag!!.
This vacuum is designed for picking up trash, organic material and other similar debris (see Safety
Warnings page 4-5).
Many vacuums are used where dust is mixed with trash. Your unit can intermittently vacuum in dusty areas.
However, following these rules will help maintain your machine's ability to vacuum in dusty conditions:
•Run machine at idle to quarter throttle.
•Machine or pressure-wash debris bag if normal cleaning does not fully clean bag. Bag should be
thoroughly dry before use.
Part No 840186
16
Form No F030106A
MV650H PUSH Vacuum Owner’s Manual
Having one or more spare bags (840189) is a good way to reduce down time while dirty bags are being
cleaned.
Felt Bag (840194) accessory is great when used in dusty conditions.
Hint!
HANDLING and TRANSPORTING
Using two people to lift unit is recommended. Lift holding the handle and front of nozzle. Make sure equipment
is properly secured before transporting.
NEVER lift the machine while the engine is running.
STORAGE
DO NOT store engine in an enclosed or poorly ventilated area where fuel fumes may
reach an open flame or spark from a furnace, water heater, clothes dryer or similar
devices.
DO NOT drain fuel in an enclosed or poorly ventilated area.
DO NOT smoke when draining fuel.
DO NOT remove gas cap while engine is running.
DO NOT park equipment on a steep grade or slope.
ALWAYS remove spark plug wire when servicing equipment to prevent accidental
starting.
ALWAYS keep hands and feet away from moving or rotating parts.
ALWAYS store fuel in approved safety containers.
If the equipment will not be used for 30 days or more, prepare as follows:
1. Make sure engine is cool.
2. Drain gasoline from carburetor and fuel tank to prevent formation of gum deposits.
3. Run engine until tank is empty and engine runs out of gas.
Fuel stabilizer (such as Sta-Bil TM) is an acceptable alternative for minimizing the formation of
gum deposits during storage. Add stabilizer to gasoline in storage container or fuel tank. Follow
stabilizer manufacturer’s instructions to determine proper mix ratio. Run engine at least 10
minutes after adding stabilizer to allow it to reach carburetor.
Form No F030106A
17
Part No 840186
MV650H PUSH Vacuum Owner’s Manual
MAINTENANCE
PERIODIC MAINTENANCE
Periodic maintenance should be performed at the following intervals:
Maintenance Operation
Every Use
Daily or Every 5 Every 25 Hours
Hours
Every 50
Hours
Every 100-150
Hours
z
Inspect for worn or damaged parts.
Check for excessive vibration
Inspect for loose parts.
z
z
z
Clean Debris Bag
z
Lubricate throttle control cable and linkage.
NOTE: Use white lithium grease or equivalent
IMPELLER REMOVAL
READ all safety instructions before servicing unit.
DISCONNECT spark plug wire before servicing unit.
Tools required:
-
-
-
-
-
1/2” socket, 3/8” drive and 3/8” ratchet
drive extension, 3/8” drive
universal joint, 3/8” drive
pry bar or long screwdriver
jack stands or similar device adequate to support weight of machine.
1. Wait for engine to cool and disconnect spark plug.
2. Drain fuel and oil from the engine.
3. Remove engine, impeller and mounting plate by removing bolts around outside of housing.
4. Leaving engine fastened to plate, remove impeller bolt and lock washer and slide impeller off crankshaft
(A puller may be required). CAUTION: Do not drop impeller.
5. If impeller does not slide off crankshaft, place two crowbars between impeller and housing on opposite
sides. Pry impeller away from engine until it loosens. Using a penetrating oil can help loosen a stuck
impeller.
6. If the impeller cannot be loosened, obtain a 3/8-24x3 ¾” longer bolt of the same diameter and thread type
as the impeller bolt. Invert engine and impeller and support engine above ground to prevent recoil
damage. Thread longer bolt by hand into the crankshaft until bolt bottoms. Using a suitable gear or
wheel puller against the bolt head and the impeller back-plate (near the blades), remove impeller from
shaft.
7. To reinstall impeller, use a new impeller bolt and lockwasher
8. Tighten impeller bolt. Torque impeller bolt to 50 Ft. Lbs. (68 N.m).
9. Reinstall engine, impeller, and mounting plate onto housing in reverse order of removal.
10. Before connecting spark plug wire, slowly pull engine starting rope to insure that impeller rotates freely.
11. Reconnect spark plug wire.
Part No 840186
18
Form No F030106A
MV650H PUSH Vacuum Owner’s Manual
WIRING DIAGRAMS
Bag Switch Circuit Schematic Diagram
TROUBLESHOOTING
Problem
Will not vacuum or has poor vacuum
performance.
Possible Cause
· Dirty or full debris bag or filter.
Solution
· Clean debris bag and filter. Shake bag clean or
wash.
· Nozzle height set too high or too low.
· Hose kit cap missing.
· Adjust nozzle height (see page 14).
· Check for hose kit cap.
· Clogged nozzle or exhaust.
· Excessive quantity of debris.
· Unclog nozzle or exhaust (see page 16)
· Allow air to feed with debris.
Abnormal vibration.
Engine will not start.
· Loose or out of balance impeller.
· Loose engine.
· Check impeller and replace if required.
· Check engine (see page 24 ).
· Throttle in off position.
· Check throttle control (see page 13).
· Engine not in full choke position.
· Check throttle, choke position (see page 13).
· Out of gasoline or bad, old gasoline.
· Spark Plug wire disconnected.
· Gas valve off.
· Check gasoline.
· Connect spark plug wire.
· Turn on gas valve.
· Dirty air cleaner.
· Clean or replace air cleaner. Contact a qualified
service person.
· Safety Interlock disengaged on bag plate.
· Latch the bag properly or check thr bag rod to see
if it's bent.
Engine is locked, will not pull over.
· Impeller plugged or clogged.
· Engine problem.
· Remove debris (see page 16).
· Contact an engine servicing dealer for engine
problems.
Form No F030106A
19
Part No 840186
MV650H PUSH Vacuum Owner’s Manual
ENGINE MAINTENANCE AND REPAIR
Refer to the engine manufacturer’s manual for maintenance and service information. Warranty coverage on the
engine is the responsibility of the engine manufacturer. If your engine requires warranty repair contact your local
servicing engine dealer. Have your engine model number and serial number ready when you contact the dealer.
If you cannot locate a servicing dealer in your area, you may contact the manufacturer’s national service
organization at the following numbers:
American Honda
(800) 426-7701
WARRANTY CLAIM PROCEDURE
Should a BILLY GOAT ® machine fail due to a defect in material and/or workmanship, the owner should make a
warranty claim as follows:
•
•
•
The machine must be taken to the dealer from whom it was purchased or to an authorized Servicing
BILLY GOAT Dealer.
The owner must present the remaining half of the Warranty Registration Card, or, if this is not available,
the invoice or receipt.
The Warranty Claim will be completed by the authorized BILLY GOAT Dealer and submitted to their
respective BILLY GOAT Distributor for their territory Attention: Service Manager. Any parts replaced
under warranty must be tagged and retained for 90 days. The model number and serial number of the
unit must be stated in the Warranty Claim.
•
•
The distributor service manager will sign off on the claim and submit it to BILLY GOAT for consideration.
The Technical Service Department at BILLY GOAT will study the claim and may request parts to be
returned for examination. BILLY GOAT will notify their conclusions to the distributor service manager
from whom the claim was received.
•
The decision by the Technical Service Department at BILLY GOAT to approve or reject a Warranty
Claim is final and binding.
Part No 840186
20
Form No F030106A
MV650H PUSH Vacuum Owner’s Manual
MAINTENANCE RECORD
Date
Service Performed
Form No F030106A
21
Part No 840186
MV650H PUSH Vacuum Owner’s Manual
ILLUSTRATED PARTS LIST
Nozzle Assembly
Figure 1
Part No 840186
22
Form No F030106A
MV650H PUSH Vacuum Owner’s Manual
Nozzle Assembly Parts List
PART
MV650H
ITEM NO. NUMBER DESCRIPTION
QTY.
1
1
2
2
2
1
3
1
2
3
1
2
2
2
1
1
1
2
1
1
1
1
2
1
1
1
1
2
1
1
1
1
8
1
2
1
3
3
1
350127 YOKE 1/2 - 20
2
350128 PIN YOKE 1/2"
3
4
8024060 BOLT CARRIAGE 3/8-16X1 1/2" ZP
8172009 WASHER 3/8" SAE ZP
5
6
7
8
8161042 NUT LOCK 3/8-16 LT WT THIN ZP
8041038 SCREWCAP 5/16 -18 x 3 1/2
8160002 NYLON INSERT LOCKNUT 5/16-18 UNC
8172020 WASHER FLAT FENDER 5/16
8161044 NYLON INSERT LOCKNUT 1/2-13 UNC THIN
8171002 WASHER 1/4" FC ZP
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
400424 LABEL WARNING OPEI
8024050 BOLTCARRIAGE 5\16-18X3 1\2
520156 ROLL PIN 1/4 X 1 LONG
8172011 WASHER 1/2" SAE ZP
840118 NOZZLE MV VAC ASSEMBLY
840019 CAP 5 IN HOSE VAC
840024 HANDLE LOWER MV VAC
840101 WHEEL 14" ASSEMBLY WITH BEARING AND TIRE
840104 AXLE FRONT WA MV VAC
840155 HGT ADJ WA W/LABEL MV VAC
8041004 SCREWCAP 1/4 - 20 x 0.75 HWH
840034 LINK HGT ADJ MV VAC
840041 BRACKET NOZZLE WEAR GUARD MV VAC
840029 ROD CONNECT HGT ADJ
840073 BUSHING 0.5" ID 0.625 OD X X 0.250
840119 ROD HANDLE CRANK ASSEMBLY
840057 HANDLE CRANK 0.5 ID X 3.72 LONG
840078 BUSHING 3/8" ID 1/2" OD X 3/8" LONG
840158 WASHER LOCK 1/4" TWISTED TOOTH
840089 NUT PAL 1/2" DIA
804135 NOZZLE COVER MV VAC
840055 LABEL PRODUCT DECAL MV
840035 SCREW PLASTIC
840054 LABEL HGT ADJ MV VAC
8122082 SCREW SELF-TAP 5/16 NC X 3/4 HEX
840088 BRACKET NOZZLE COVER REINFORMENT MV
8024021 BOLT CARRIAGE 1/4-20X0.75
900455 NUT FLANGE 1/4-20
Form No F030106A
23
Part No 840186
MV650H PUSH Vacuum Owner’s Manual
Engine Assembly
Figure 3
Part No 840186
24
Form No F030106A
MV650H PUSH Vacuum Owner’s Manual
Engine Assembly Parts List
ITEM
NO.
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
PART
MV650H
QTY.
1
NUMBER DESCRIPTION
840069 ENGINE HONDA 6.5 VERTICAL GSV190
840137 IMPELLER ASSEMBLY PUSH MV VAC
840111 PLATE TOP WA PUSH MV VAC
840003 HOUSING PLASTIC VAC
400502 WASHER LOCK 3/8 TWISTED TOOTH
400268 LABEL HOT ENGINE
1
1
1
1
1
1
1
1
6
6
6
1
3
6
1
2
9201087 SQ KEY 2.125 X .187
840045 CONTROL THROTTLE MV VAC
8160001 NYLON INSERT LOCKNUT 1/4-20 UNC
8172007 WASHER 1/4" SAE ZP
8172019 WASHER FENDER 1/4 ZP
8041004 SCREWCAP 1/4 - 20 x 0.75 HWH
790167 SCREWCAP 3/8-24X2 3/4" W/PATCH LOCK
900564 SCREWCAP 3/8"-16X2 1/2" TAPTITE
890359 SCREWCAP 1/4 - 20 x 5/8 HWH
8041018 SCREWCAP 1/4"-20X4" HCS ZP
8171002 WASHER 1/4" FC ZP
840083 SPACER 1.50OD X .875ID X .5 THK
1
Form No F030106A
25
Part No 840186
MV650H PUSH Vacuum Owner’s Manual
Hood Assembly
Figure 4
Part No 840186
26
Form No F030106A
MV650H PUSH Vacuum Owner’s Manual
Hood Assembly
ITEM
NO .
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
188
189
190
191
192
193
PART
NUM B ER DESCRIPTIO N
M V650H
Q TY.
840141
840153
840196
840037
840038
840154
840152
840195
840138
840061
840062
850190
840058
840077
HO O D ASSY W / LABEL M V VAC
BRACKET BAG CHANNEL RH W /SEAL M V VAC
SEAL BAG M V VAC
TU BE HANDLE BRAC E RH M V VAC
TU BE HANDLE BRAC E LH M V VAC
BRACKET BAG CHANNEL RH W /SEAL M V VAC
BRACKET NO ZZLE DO O R ADJ W /LABEL M V VAC
BAG ASSEM BLY M V VAC
BAR LIFT NO ZZLE D O O R W / G RIP M V VAC
RO D LIFT NO ZZLE DO O R SP VAC
PLATE BAG LATCH M V VAC
G RIP LEVER LIFT
SW ITCH INTERLO CK VAC
1
1
1
1
1
1
1
1
1
1
2
1
1
1
7
9
8
4
8
4
6
1
11
3
1
1
1
HARNESS W IR E ASSY M V VAC
8024025 BO LT CARRIAG E 1/4-20 X 1.75
8171002 W ASHER 1/4" FC ZP
8160001 NYLO N IN SERT LO CKNUT 1/4-20 UNC
520018
SCREW HEX HEAD #10-24 X 1"
8172005 W ASHER #10 SAE ZP
8164005 NYLO N IN SERT LO CKNUT 10-24 UNC
900407
610347
TY W RAP
PIN SCREW 1/4-28
8171003 W ASHER 5/16 FLATW ASH ER Z/P
8160002 NYLO N IN SERT LO CKNUT 5/16-18 UNC
610429
610348
SPR ING LEVER G Z
FIBRE W ASHER
8041032 SCREW CAP 5/16"-18 X 2 ZP
8041031 SCREW CAP 5/16-18 X 1.75 ZP
8172007 W ASHER 1/4" SAE ZP
2
4
1
1
2
1
2
1
1
2
3
2
1
2
1
1
2
890254
890301
400886
LABEL EAR EYE BR EATH ING
LABEL READ
RO D END BALL JO INT 3/8 NF
8041052 SCREW CAP 3/8-16X1 1/2 ZP
8160003 NYLO N IN SERT LO CKNUT 3/8-16 UNC
8041056 SCREW CAP 3/8"-16X2 1/2" ZP
840197
SEAL BAG FR O NT HO O D 20.5 LO NG
8149003 NUT REG 3/8-24 NF
8041004 SCREW CAP 1/4"-20X3/4" HC S ZP
8172019 W ASHER FENDER 1/4 ZP
8041018 SCREW CAP 1/4"-20X4" HC S ZP
840071
810736
840080
840113
840114
840040
840139
360203
840189
NUT AC O RN 1/4-20
LABEL DANG ER FLYIN G DEBRIS
LABEL NO ZZLE DO O R M V VAC
PLUG SNAP RIVET 0.166 D IA
PLUG SNAP RIVET 0.232 D IA
RO D BAG W A M V VAC
LATCH R UBBER ASSEM BLY M V VAC
PAL N UT 0.312
BAG DEBRIS M V VAC
1
2
2
1
Form No F030106A
27
Part No 840186
MV650H PUSH Vacuum Owner’s Manual
Rear Axle Assembly
Figure 2
Rear Axle Assembly Parts List
ITEM
PART
MV650H
NO. NUMBER DESCRIPTION
QTY.
200
201
202
203
204
205
206
207
8172011 WASHER FLAT 1/2" SAE
8024046 BOLT CARRIAGE 5/16-18X2 1/2
8171002 WASHER 1/4" FC ZP
8160002 NYLON INSERT LOCKNUT 5/16-18 UNC
8161044 NYLON INSERT LOCKNUT 1/2-13 UNC THIN
840091 SHAFT REAR AXLE PUSH VAC
840090 BRACKET REAR AXLE MOUNT PUSH MV VAC
840101 WHEEL 14" ASSEMBLY WITH BEARING AND TIRE
2
4
4
4
2
1
2
2
Part No 840186
28
Form No F030106A
|